2001 Toyota Corolla Owners Manual

increased when

(cid:1) Because stopping distance may be in- vehicle–to–vehicle distance creased, should be towing a trailer. For each 16 km/h (10 mph) of speed, allow at least one vehicle and trailer length between you and the ve- hicle ahead. Avoid sudden braking as you may skid, resulting in jackknifing and loss of control. This is especially true on wet or slippery surfaces.

(cid:1) Avoid jerky starts or sudden accelera- tion. If your vehicle has a manual transmission, prevent excessive clutch slippage by keeping engine rpm low and not racing the engine. Always start out in first gear.

(cid:1) Avoid jerky steering and sharp turns. The trailer could hit your vehicle in a tight turn. Slow down before making a turn to avoid the necessity of sudden braking.

TRAILER TOWING TIPS When towing a trailer, your vehicle will handle differently than when not tow- ing. The three main causes of vehicle– trailer accidents are driver error, exces- sive speed and improper trailer loading. Keep these in mind when towing: (cid:1) Before starting out, check operation of the lights and all vehicle–trailer connec- tions. After driving a short distance, stop and recheck the lights and con- nections. Before actually towing a trail- er, practice turning, stopping and back- ing with a trailer in an area away from traffic until you learn the feel.

(cid:1) Backing with a trailer is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This pro- cedure that when backing without a trailer). Also, just turn the steering wheel a little at time, avoiding sharp or prolonged turning. Have someone guide you when backing to reduce the risk of an acci- dent.

is generally opposite

to

MAINTENANCE (cid:1) If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. For this informa- tion, please the scheduled maintenance information in the “Sched- uled Maintenance Guide” or “Owner’s Manual Supplement”.

refer

to

(cid:1) Retighten all fixing bolts of the towing ball and bracket after approximately 1000 km (600 miles) of trailer driving.

PRE–TOWING SAFETY CHECK (cid:1) Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle has an abnormal nose–up or nose–down condition, and check improper tongue load, overload,worn suspension or other possible causes.

for

(cid:1) Make sure the trailer cargo is securely

loaded so that it can not shift.

(cid:1) Check that your rear view mirrors con- form to any applicable federal, state/ provincial or local regulations. If not, install the rear view mirrors required for towing purpose.

166

2001MY_COROLLA_U (OM12720U)

(cid:1) Remember that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Therefore, compensate for this by making a turning radius with your vehicle.

than normal

larger

(cid:1) Crosswinds and rough roads will ad- versely affect handling of your vehicle and trailer, causing sway. Pay attention to the rear from time to time to pre- pare yourself for being passed by large trucks or buses, which may cause your vehicle and trailer to sway. If swaying happens, firmly grip the steering wheel and immediately but gradually. Never increase speed. Steer straight ahead. If you make no extreme correction with the steering or brakes, the vehicle and trailer will stabilize.

reduce speed

(cid:1) Be careful when passing other ve- hicles. Passing requires considerable distance. After passing a vehicle, do not forget the length of your trailer and be sure you have plenty of room be- fore changing lanes.

’01 Corolla U (L/O 0005)

(cid:1) In order to maintain engine braking effi- ciency do not use fifth gear (manual transmission) or overdrive (automatic transmission).

(at

(cid:1) Because of the added load of the trail- er, your vehicle’s engine may overheat on hot days temperatures over 30(cid:2)C [85(cid:2)F]) when going up a long or steep grade with a trailer. If the engine coolant indicates overheating, immediately turn off the air conditioning (if in use), pull off the road and stop in a safe spot. Refer to “If your vehicle overheats” in Section 4.

temperature gauge

(cid:1) Always place wheel blocks under both the vehicle and trailer wheels when parking. Apply the parking brake firmly. Put the transmission in “P” (automatic) or in first or reverse (manual). Avoid parking on a slope with a trailer, but if it cannot be avoided, do so only after performing the following:

1. Apply the brakes and hold. 2. Have someone place wheel blocks un- der both the vehicle and trailer wheels. 3. When the wheel blocks are in place, the

release your brakes slowly until blocks absorb the load.

4. Apply the parking brake firmly. 5. Shift into first or reverse (manual) or “P” (automatic) and turn off the engine. When restarting out after parking on a slope: 1. With the transmission in “P” position the clutch pedal de- the engine. transmission, be the brake pedal de-

(automatic) or pressed (With an automatic sure pressed.)

(manual), start

to keep

2. Shift into gear. 3. Release the parking brake (also foot brake on automatic transmission ve- hicles) and slowly pull or back away from the wheel blocks. Stop and apply your brakes.

4. Have someone retrieve the blocks.

2001MY_COROLLA_U (OM12720U)

167

’01 Corolla U (L/O 0005)

CAUTION

speed

towing

(cid:1) Do not exceed 72 km/h (45 mph) or the posted lim- it,whichever is lower. Because insta- bility (swaying) of a towing vehicle– trailer in- creases as the speed increases, ex- ceeding 72 km/h (45 mph) may cause loss of control.

combination

usually

(cid:1) Slow down and downshift before descending steep or long downhill grades. Do not make sudden down- shifts.

long or

(cid:1) Avoid holding the brake pedal down too frequently. This could cause the brakes to overheat and result in reduced braking effi- ciency.

too

fuel

How to save fuel and make your vehicle last longer, too Getting more kilometers/mileage from a liter/gallon of take it is easy—just easy. It will help make your vehicle last longer, too. Here are some specific tips on how to save money on both fuel and repairs: (cid:1) Keep your tires inflated at the cor- rect pressure. Underinflation causes tire wear and wastes fuel. See Section 7–2 for instructions.

(cid:1) Do not carry unneeded weight

in your vehicle. Excess weight puts a heavier the engine, causing greater fuel consumption.

load on

(cid:1) Avoid lengthy warm–up idling. Once the engine is running smoothly, begin driving—but gently. Remember, howev- er, that on cold winter days this may take a little longer.

(cid:1) Keep

the automatic

transmission overdrive turned on when engine braking is not required. Driving with the overdrive off will reduce the fuel economy. (For details, see “Automatic transmission” in Section 1–6.)

(cid:1) Accelerate

slowly

smoothly. Avoid jackrabbit starts. Get into high gear as quickly as possible.

and

168

2001MY_COROLLA_U (OM12720U)

(cid:1) Avoid long engine idling. If you have a long wait and you are not in traffic, it is better to turn off the engine and start again later.

(cid:1) Avoid engine

lugging or over–rev- ving. Use a gear position suitable for the road on which you are travelling.

(cid:1) Avoid continuous speeding up and slowing down. Stop–and–go driving wastes fuel.

(cid:1) Avoid unnecessary stopping and braking. Maintain a steady pace. Try to time the traffic signals so you only need to stop as little as possible or take advantage of through streets to avoid traffic lights. Keep a proper dis- tance from other vehicles to avoid sud- den braking. This will also reduce wear on your brakes.

(cid:1) Avoid heavy traffic or traffic

whenever possible.

jams

(cid:1) Do not rest your foot on the clutch or brake pedal. This causes premature wear, overheating and poor fuel econo- my.

(cid:1) Maintain a moderate speed on high- ways. The faster you drive,the greater the fuel consumption. By reducing your speed, you will cut down on fuel con- sumption.

the

(cid:1) Keep

front wheels

in proper alignment. Avoid hitting the curb and slow down on rough roads. Improper alignment not only causes faster tire wear but also puts an extra load on the engine, which, in turn, wastes fuel. (cid:1) Keep the bottom of your vehicle free from mud, etc. This not only lessens weight but also helps prevent corro- sion.

(cid:1) Keep your vehicle tuned–up and in top shape. A dirty air cleaner, improp- er valve clearance, dirty plugs, dirty oil and grease,brakes not adjusted, etc. all lower engine performance and contrib- ute to poor fuel economy. For longer life of all parts and lower operating costs, keep all maintenance work on schedule, and if you often drive under severe conditions, see that your vehicle frequent maintenance. receives more (For scheduled maintenance informa- tion, please refer the “Scheduled Maintenance Guide” or “Owner’s Manu- al Supplement”.

to

’01 Corolla U (L/O 0005)

CAUTION

Never turn off the engine to coast down hills. Your power steering and brake booster will not function with- out the emission control system operates properly only when the engine is run- ning.

the engine running. Also,

2001MY_COROLLA_U (OM12720U)

169

’01 Corolla U (L/O 0005)

170

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

eU-5

Quick index (cid:1) If a service reminder indicator or warning buzzer comes on (cid:1) If your vehicle will not start (cid:1) If your engine stalls while driving (cid:1) If your vehicle overheats (cid:1) If you have a flat tire (cid:1) If your vehicle needs to be towed (cid:1) Tips for driving during break–in period (cid:1) How to start the engine (cid:1) General maintenance (cid:1) Complete index Gas station information Fuel type:

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

86
172
175
175
176
185
146
160
197
NO TAG

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

UNLEADED gasoline, Octane Rating 87 (Research Octane Number 91) or higher See page 146 for detailed information.

Fuel tank capacity:

50 L (13.2 gal., 11.0 lmp. gal.)

Engine oil:

API grade SJ, “Energy–Conserving” or ILSAC multigrade engine oil is recommended. See page 208 for detailed information.

Automatic transmission fluid:

Automatic transmission fluid D–II or DEXRON(cid:2)III (DEXRON(cid:2)II) See page 236 for detailed information.

Tire information: See pages 212 through 216. Tire pressure: See page 237.

2001MY_COROLLA_U (OM12720U)

Publication No. OM12720U Part No. 01999-12720
Printed in Japan 01–0005–00

( U)

’01 Corolla U (L/O 0005)

SECTION 4

IN CASE OF AN EMERGENCY If your vehicle will not start If your engine stalls while drivin If your vehicle overheats If you have a flat tire If your vehicle needs to be towe If you cannot shift automatic transmission selector leve If you lose your keys

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

172
175
175
176
185
187
188

2001MY_COROLLA_U (OM12720U)

171

’01 Corolla U (L/O 0005)

If the engine turns over at its normal speed but will not start— 1. Turn ignition key

the

to

“ACC” or the engine

“LOCK” and again.

try starting

2. If the engine will not start, the engine may be flooded because of repeated cranking. See “(b) Starting a flooded engine” for further instructions.

3. If the engine still will not start, it needs repair. Call a Toyota

adjustment or dealer or qualified repair shop.

(b) Starting a flooded engine If the engine will not start, your engine may be flooded because of repeated cranking. If this happens, turn the key to “START” the accelerator pedal held down. with Keep the key and accelerator pedal in these positions for 15 seconds and re- lease them. Then try starting the engine with your foot off the accelerator pedal. If the engine does not start after 15 sec- onds of cranking, release the key, wait a few minutes and try again. If the engine still will not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop for assistance.

NOTICE

Do not crank for more than 30 se- conds at a time. This may overheat the starter and wiring systems.

If your vehicle will not start— (a) Simple checks Before making these checks, make sure you have followed the correct starting pro- cedure given in “How to start the engine” in Section 3 and that you have sufficient fuel. If the engine is not turning over or is turning over too slowly— 1. Check the battery

terminals are

that

tight and clean.

2. If the battery terminals are O.K., switch

on the interior light.

3. If the light

is out, dim or goes out when the starter is cranked, the battery is discharged. You may try jump start- ing. See “(c) Jump starting” for further instructions.

If the light is O.K., but the engine still will not start, it needs adjustment or repair. Call a Toyota dealer or qualified repair shop.

NOTICE

Do not pull– or push–start the ve- hicle. It may damage the vehicle or cause a collision when the engine starts. Also the three–way catalytic converter may overheat and become a fire hazard.

172

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

(c) Jump starting To avoid serious personal injury and damage to your vehicle which might re- sult from battery explosion, acid burns, electrical burns, or damaged electronic components, these instructions must be followed precisely. If you are unsure about how to follow this procedure, we strongly that you seek the help of a competent me- chanic or towing service.

recommend

CAUTION

(cid:1) Batteries

contain

sulfuric

acid which is poisonous and corrosive. Wear protective safety glasses when jump starting, and avoid spilling acid on your skin, clothing, or ve- hicle.

(cid:1) The gas normally produced by a battery will explode if a flame or spark is brought near. Use only standardized jumper cables and do not smoke or light a match while jump starting.

NOTICE

The battery used for boosting must be 12 V. Do not jump start unless you are sure that the booster battery is correct.

JUMP STARTING PROCEDURE 1. If

the booster battery

installed in another vehicle, make sure the vehicles are not touching. Turn off all unneces- sary lights and accessories.

is

2. If required, remove all the vent plugs from the booster and discharged batter- ies. Lay a cloth over the open vents on the batteries. (This helps reduce the explosion hazard, personal injuries and burns.)

3. If the engine in the vehicle with the booster battery is not running, start it and let it run for a few minutes. During jump starting, run the engine at about 2000 rpm with the accelerator pedal lightly depressed.

(cid:1) If you should accidentally get acid on yourself or in your eyes, remove any contaminated clothing and flush the affected area with water imme- diately. Then get immediate medical attention. If possible, continue to apply water with a sponge or cloth while en route to the medical office.

2001MY_COROLLA_U (OM12720U)

173

’01 Corolla U (L/O 0005)

Discharged battery

Jumper cable

Booster battery

Positive terminal (“+” mark)

Jumper cable

Discharged battery

Positive terminal (“+” mark)

Negative terminal (“–” mark)

Booster battery

4. Make the cable connections in the or-

der a, b, c, d. a. Connect the clamp of the positive (red) jumper cable to the positive ( ) terminal on the discharged battery. b. Connect the clamp at the other end of the positive (red) jumper cable to the positive ( ) terminal on the booster battery.

c. Connect the clamp of the negative (black) jumper cable to the negative (–) terminal on the booster battery. d. Connect the clamp at the other end of the negative (black) jumper cable to a solid, stationary, unpainted, metallic point of the vehicle with the discharged battery. The recommended connecting point is shown in the following illustration:

174

2001MY_COROLLA_U (OM12720U)

Connecting point

Do not connect the cable to or near any part is cranked.

that moves when

the engine

CAUTION

the connections,

to When making avoid serious injury, do not lean over the battery or accidentally the jumper cables or clamps touch any- thing except the correct battery termi- nals or the ground.

let

’01 Corolla U (L/O 0005)

5. Start your engine in the normal way. After starting, run it at about 2000 rpm for several minutes with the accelerator pedal lightly depressed.

6. Carefully disconnect the cables in the exact reverse order: the negative cable and then the positive cable.

7. Carefully dispose of the battery cover cloths—they may now contain sulfuric acid.

8. If removed, replace all the battery vent

plugs.

If the cause of your battery discharging is not apparent (for example, lights left on), you should have it checked.

If your engine stalls while driving If your engine stalls while driving... 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Turn

ignition key

the

to try starting

“ACC” or the engine

“LOCK”, and again.

If the engine will not start, see “If your vehicle will not start”.

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

If your vehicle overheats If your engine coolant temperature gauge indicates overheating, if you ex- perience a loss of power, or if you hear a loud knocking or pinging noise, the engine has probably overheated. You should follow this procedure... 1. Pull safely off the road, stop the ve- turn on your emergency hicle and flashers. Put the transmission in “P” (automatic) or neutral (manual) and ap- ply the parking brake. Turn off the air conditioning if it is being used.

2. If coolant or steam is boiling out of the radiator or reservoir, stop the engine. Wait until the steam subsides before opening the hood. If there is no coolant boiling over or steam, leave the engine running and make sure the electric cooling fan is operating. If it is not, turn the ignition off.

CAUTION

injury, keep To help avoid personal the hood closed until there is no steam. Escaping steam or coolant is a sign of very high pressure.

2001MY_COROLLA_U (OM12720U)

175

’01 Corolla U (L/O 0005)

3. Look for obvious coolant leaks from the radiator, hoses,and under the vehicle. However, note that water draining from the air conditioning is normal if it has been used.

CAUTION

the engine

When is running, keep hands and clothing away from the moving fan and engine drive belts.

4. If the coolant is leaking, stop the en- gine immediately. Call a Toyota dealer for assistance.

5. If there are no obvious leaks, check the coolant reservoir. If it is dry, add coolant to the reservoir while the en- gine is running. Fill it about half full.

CAUTION

Do not attempt to remove the radiator cap when the engine and radiator are hot. Serious injury could result from scalding hot fluid and steam blown out under pressure.

6. After

the engine coolant

temperature has cooled to normal, again check the coolant level in the reservoir. If neces- sary, bring it up to half full again. Seri- ous coolant loss indicates a leak in the system. You should have it checked as soon as possible at your Toyota dealer.

If you have a flat tire— 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place well away from the traffic. Avoid stopping on the center divider of a highway. Park on a level spot with firm ground.

2. Stop

the engine and

turn on your

emergency flashers.

3. Firmly set the parking brake and put the transmission in “P” (automatic) or reverse (manual).

4. Have everyone get out of the vehicle

on the side away from traffic.

5. Read oughly.

the

following

instructions

thor-

CAUTION

When jacking, be sure to observe the following to reduce the possibility of personal injury: (cid:1) Follow jacking instructions.

176

2001MY_COROLLA_U (OM12720U)

(cid:1) Do not put any part of your body under the vehicle supported by the jack. Personal injury may occur.

(cid:1) Do not start or run the engine while is supported by the

your vehicle jack.

(cid:1) Stop the vehicle on a

the transmission

level firm ground, firmly set the parking brake in “P” and put (automatic) or (manual). Block the wheel diagonally opposite to the one being changed if neces- sary.

reverse

(cid:1) Make sure to set the jack properly in the jack point. Raising the ve- hicle with improperly posi- tioned will damage the vehicle or may allow the vehicle to fall off the jack and cause personal injury.

jack

(cid:1) Never get under the vehicle when the vehicle is supported by the jack alone.

’01 Corolla U (L/O 0005)

(cid:1) Use the jack only for lifting your

vehicle during wheel changing.

(cid:1) Do not raise the vehicle with some-

one in the vehicle.

(cid:1) When raising the vehicle, do not put an object on or under the jack. (cid:1) Raise the vehicle only high enough

to remove and change the tire.

NOTICE

Do not continue driving with a de- flated tire. Driving even a short dis- tance can damage a tire and wheel beyond repair.

Compact spare tire The compact spare tire is designed for temporary emergency use only. The compact spare tire is identified by the distinctive wording “TEMPORARY USE ONLY” molded into the side wall of the tire. The standard tire should be repaired and replaced as soon as possible. The compact spare tire saves space in your luggage compartment, and its lighter weight helps to improve fuel economy and permits easier installation in case of a flat tire.

2001MY_COROLLA_U (OM12720U)

177

’01 Corolla U (L/O 0005)

—Required tools and spare tire

The compact spare tire can be used many times, if necessary. It has tread life of up to 4800 km (3000 miles) depending on road conditions and your driving habits. When tread wear indicators appear on the tire, replace the tire. See also the tire section in Section 7–2
for details on the tread wear indicators and other service information.

CAUTION

NOTICE

Your ground clearance is reduced when the compact spare tire is installed so avoid driving over ob- stacles and drive slowly on rough, unpaved roads and speed bumps. Also, do not attempt to go through an automatic car wash as the vehicle may get caught, resulting in damage.

(cid:1) The compact spare

tire was de- signed especially for your Toyota. Do not use it on any other vehicle. (cid:1) Do not exceed 80 km/h (50 mph) the compact

when driving with spare tire.

Vehicles with compact spare tire

(cid:1) Avoid sudden acceleration, sudden deceleration and sharp turns with the compact spare tire.

178

2001MY_COROLLA_U (OM12720U)

Vehicles without compact spare tire

’01 Corolla U (L/O 0005)

the required

1. Get tire. Vehicles with compact spare tire

tools and spare

1. Jack handle 2. Wheel nut wrench 3. Jack 4. Spare tire

Vehicles without compact spare tire

1. Spare tire 2. Jack handle 3. Jack 4. Tool bag

To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their stor- age locations.

Turn the jack joint by hand. To remove: Turn the joint in direction 1
until the jack is free. To store: Turn the joint in direction 2 until the jack is firmly secured to prevent it flying forward during a collision or sudden braking.

To remove the spare tire: 1. Raise the luggage compartment floor. 2. On vehicles with compact spare tire,

take the tool holder with tools out.

3. Loosen the bolt with spacer and re-

move it.

Then take the spare tire out of the ve- hicle. When storing the spare tire, put it in place with the outer side of the wheel facing up. Then secure the above removal steps in reverse order to prevent forward during a collision or sudden braking.

repeating

tire by

flying

from

the

it

2001MY_COROLLA_U (OM12720U)

179

’01 Corolla U (L/O 0005)

—Blocking the wheel

—Removing wheel ornament

3. Remove the wheel ornament. Pry off the beveled end of the wheel nut wrench as shown.

the wheel ornament, using

CAUTION

Do not try to pull off the ornament by hand. Take due care in handling the ornament to avoid unexpected person- al injury.

Type A

2. Block the wheel diagonally opposite the flat tire to keep the vehicle from rolling when it is jacked up.

When blocking the wheel, place a wheel block from the front for the front wheels or from the rear for the rear wheels.

180

2001MY_COROLLA_U (OM12720U)

Type B

’01 Corolla U (L/O 0005)

—Loosening wheel nuts

—Positioning the jack

—Raising your vehicle

4. Loosen all the wheel nuts. Always loosen the wheel nuts before rais- ing the vehicle. Turn the wheel nuts counterclockwise to loosen. To get maximum leverage, fit the wrench to the nut so that the handle is on the right side, as shown above. Grab the wrench near the end of the handle and pull up on the handle. Be careful that the wrench does not slip off the nut. Do not remove the nuts yet—just unscrew them about one–half turn.

5. Position the jack at the correct jack

point as shown.

Make sure the jack level and solid place.

is positioned on a

6. After making sure that no one is in the vehicle, raise it high enough so that the spare tire can be installed. Remember you will need more ground clearance when putting on the spare tire than when removing the flat tire. To raise the vehicle, insert the jack handle into the jack (it is a loose fit) and turn it clockwise. As the jack touches the vehicle and begins to lift, double–check that it is properly positioned.

2001MY_COROLLA_U (OM12720U)

181

’01 Corolla U (L/O 0005)

—Changing wheels

CAUTION

Never get under the vehicle when the vehicle jack alone.

is supported by

the

7. Remove the wheel nuts and change

tires.

it

the flat

the spare wheel

tire straight off and put

Lift aside. Roll into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.

Before putting on wheels, remove any cor- rosion on the mounting surfaces with a wire brush or such. Installation of wheels without good metal–to–metal contact at the mounting surface can cause wheel nuts to loosen and eventually cause a wheel to come off while driving. Therefore after the first 1600 km (1000 miles), check to see that the wheel nuts are tight.

182

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

—Reinstalling wheel nuts

—Lowering your vehicle

CAUTION

When lowering the vehicle, make sure all portions of your body and all oth- er persons around will not be injured as the ground.

the vehicle

lowered

to

is

8. Reinstall all the wheel nuts finger

tight.

Reinstall the wheel nuts (tapered end in- ward) and tighten them as much as you can by hand. Press back on the tire and see if you can tighten them more.

9. Lower

the vehicle completely and

tighten the wheel nuts.

Turn the jack handle counterclockwise to lower the vehicle. Use only the wheel nut wrench to tighten the nuts. Do not use other tools or any additional leverage other than your hands, such as a hammer, pipe or your foot. is securely en- Make sure gaged over the nut. Tighten each nut a little at a time in the order shown. Repeat the process until all the nuts are tight.

the wrench

2001MY_COROLLA_U (OM12720U)

183

’01 Corolla U (L/O 0005)

10. Reinstall the wheel ornament. 1. Put the wheel ornament into position. On some models, align the cutout of the wheel ornament with the valve stem as shown. 2. Then tap it firmly with the side or heel

of your hand to snap it into place.

CAUTION

Take due care in handling the orna- ment to avoid unexpected personal injury.

—After changing wheels 11. Check the air pressure of the re-

placed tire.

Adjust the air pressure to the specification designed in Section 8. If the pressure is lower, drive slowly to the nearest service station and fill to the correct pressure. Do not forget to reinstall the tire inflation valve cap as dirt and moisture could get into the valve core and possibly cause air leakage. If the cap is missing, have a new one put on as soon as possible. 12. Restow all the tools, jack and flat

tire securely.

As soon after changing wheels as pos- sible, tighten the wheel nuts to the torque specified torque wrench. Have a technician repair the flat tire and replace the spare tire with it.

in Section 8 with a

CAUTION

Before driving, make sure all the tools, jack and flat tire are securely in place in their storage location to reduce the possibility of personal in- jury during a collision or sudden braking.

2001MY_COROLLA_U (OM12720U)

—Reinstalling wheel ornament

Type A

Type B

184

’01 Corolla U (L/O 0005)

If your vehicle needs to be towed—

(a) Towing with wheel lift type truck—

—From front

—From rear

(b) Using flat bed truck

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. In consultation with them, have your vehicle towed using either (a) or (b). Only when you cannot receive a towing service from a Toyota dealer or com- mercial tow truck service, tow your ve- hicle carefully in accordance with the instructions given in “—Emergency tow- ing” in this section. Proper equipment will help ensure that your vehicle is not damaged while being towed. Commercial operators are generally aware of local laws pertaining to towing. Your vehicle can be damaged is towed incorrectly. Although most operators know the correct procedure, it is possible to make a mistake. To avoid damage to your vehicle, make sure the following pre- cautions are observed. If necessary, show this page to the tow truck driver. TOWING PRECAUTIONS: Use a safety chain system for all towing, and abide by the state/provincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly.

the state/provincial and

it

if

(a) Towing with wheel lift type truck From front—Release the parking brake.

NOTICE

When lifting wheels, take care to en- sure adequate ground clearance for towing at the opposite end of the raised vehicle. Otherwise, the bumper and/or underbody of the towed vehicle will be damaged during towing.

From rear— (cid:1) Manual transmission:

We recommend using a towing dolly under the front wheels. If you do not use a towing dolly, place the ignition key in the “ACC” position and put the transmission in neutral.

NOTICE

Do not tow with the key removed or in the “LOCK” position when towing from the rear without a towing dolly. The steering lock mechanism is not strong enough to hold the front wheels straight.

2001MY_COROLLA_U (OM12720U)

185

(cid:1) Automatic transmission:

Use a wheels.

towing dolly under

the

front

NOTICE

Never tow a vehicle with an automatic transmission from the rear with the front wheels on the ground, as this may cause serious damage to the transmission.

(b) Using flat bed truck

’01 Corolla U (L/O 0005)

(c) Towing with sling type truck

—Emergency towing

(c) Towing with sling type truck

NOTICE

Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.

If towing is necessary, we recommend you to have it done by your Toyota dealer or a commercial tow truck ser- vice. If towing service is not available in an emergency, your vehicle may be tempo- rarily towed by a cable or chain se- cured to the emergency towing eyelet under the vehicle. Use extreme caution when towing vehicles.

186

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

If you cannot shift automatic transmission selector lever

NOTICE

NOTICE

Only use specified towing eyelet; otherwise your vehicle may be dam- aged.

A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard–surfaced roads for a short dis- tance and at the wheels, axles, drive train, steering and brakes must all be in good condition.

low speeds. Also,

CAUTION

Use extreme caution when towing ve- hicles. Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing eyelets and towing cable or chain. The eyelets and towing cable or chain may break and cause serious injury or damage.

Use only a cable or chain specifically intended for use in towing vehicles. Securely fasten the cable or chain to the towing eyelets provided.

Before towing, release the parking brake and put the transmission in neutral (manu- al) or “N” (automatic). The key must be in “ACC” (engine off) or “ON” (engine run- ning).

CAUTION

If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.

though

If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Turn

the brake pedal

ignition key

the

to “LOCK” the parking

position. Make sure brake is on.

2. Pry up the cover with a flat–bladed

screwdriver or equivalent.

2001MY_COROLLA_U (OM12720U)

187

’01 Corolla U (L/O 0005)

in “Keys”

the suggestion given

If you lose your keys You can purchase a new key at your Toyota dealer if you can give them the key number. See Section 1–2. If your keys are locked in the vehicle and you cannot get a duplicate, many Toyota dealers can still open the door for you, using If you must break a window in, we suggest breaking the smallest side window be- cause it is the least expensive to replace. Be extremely cautious to avoid cuts from the glass.

their special

to get

tools.

in

3. Insert your finger into the hole to push down the shift lock override button. You can shift out of “P” position only while pushing the but- ton.

4. Shift into “N” position. 5. Insert the cover. 6. Start the engine. For your safety,

keep the brake pedal depressed.

Be sure to have the system checked by your Toyota dealer as soon as possible.

188

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

SECTION 5

CORROSION PREVENTION AND APPEARANCE CARE Protecting your Toyota from corrosio Washing and waxing your Toyota Cleaning the interior

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

190
191
193

2001MY_COROLLA_U (OM12720U)

189

’01 Corolla U (L/O 0005)

(cid:1) Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.

(cid:1) High ambient temperatures can cause corrosion to those components of the vehicle which are prevented from quick–drying due to lack of proper ven- tilation.

The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: (cid:1) If you drive on salted roads

the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.

in

(cid:1) High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing them. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as these areas can cause corrosion.

trapped water

in

(cid:1) Wash the underside of the vehicle thor-

oughly when winter is over.

See “Washing and waxing your Toyota” for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.

the

Protecting your Toyota from corrosion Toyota, through its diligent research, de- sign and use of the most advanced technology available, has done its part to help prevent corrosion and has provided you with vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long– term corrosion prevention. The most common causes of corrosion to your vehicle are: (cid:1) The accumulation of road salt, dirt and moisture in hard–to–reach areas under the vehicle.

quality

finest

(cid:1) Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.

Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: (cid:1) Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea– coast or in areas of industrial pollution. (cid:1) High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.

190

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, etc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full–size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your Toyota dealer will be happy to assist in supplying and installing the shields if they are recommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it in covered with water or snow, your garage may be so damp it will cause corrosion. Even if your garage is heated, a wet vehicle can corrode if the ventilation is poor.

Washing and waxing your Toyota Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. (cid:1) When driving in a coastal area (cid:1) When driving on a road sprinkled with

antifreeze

(cid:1) When having stuck of coal

tree sap, bird droppings and carcass of an insect

tar,

(cid:1) When driving in the areas where there is a lot of smoke, soot, dust, iron dust and chemical substance

(cid:1) When the vehicle becomes remarkably

dirty with dust and mud Hand–washing your Toyota Work in the shade and wait until the vehicle body is not hot to the touch.

CAUTION

When cleaning under floor or chassis, be careful not to injure your hands.

1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the wheel wells.

the vehicle or

in

2. Wash with a mild car–wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.

Plastic wheel ornaments: The plastic wheel ornaments are damaged easily by organic substances. If any organic sub- stances splashes an ornament, be sure to wash it off with water and check if the ornament is damaged.

CAUTION

Do not attach the heavily damaged plastic wheel ornament. It may fly off the wheel and cause accidents while the vehicle is moving.

2001MY_COROLLA_U (OM12720U)

191

’01 Corolla U (L/O 0005)

Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some type of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle.

NOTICE

To prevent damage to the antenna, make sure it is retracted before driv- ing your Toyota through an automatic car wash.

Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Once a month or if the vehicle surface does not repel water well, apply wax. 1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.

2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car–cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. the vehicle again when water does not bead but remains on the sur- face in large patches.

3. Wax

NOTICE

Always remove the plastic bumpers if your vehicle is re–painted and placed in a high heat paint waxing booth. High temperatures could damage the bumpers.

Aluminum wheels: Use only a mild soap or neutral detergent. Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft. Road turpentine or cleaners that are marked safe for painted surfaces.

tar: Remove with

NOTICE

Do not use organic substances (gaso- line, kerosene, benzine or strong sol- vents), which may be toxic or cause damage.

3. Rinse

thoroughly—dried

can In hot weather you cause streaking. may need to rinse each section right after you wash it.

soap

4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.

192

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

Cleaning the interior

CAUTION

(cid:1) Vehicles with side airbags:

Be careful not to splash water or spill liquid on the floor. This may prevent the side airbags from acti- vating correctly, resulting in serious injury.

(cid:1) Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interior or exterior. Water may get into audio components or other electrical components above or un- der the floor carpet (or mat) and cause a malfunction; and it may cause body corrosion.

Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming– type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.

NOTICE

Do not use solvent, thinner, gasoline or window cleaner on the interior.

to

foam–type shampoo

Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol can sand others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.

NOTICE

(cid:2) Do not use dye or bleach on the

belts—it may weaken them.

(cid:2) Do not use the belts until they be-

come dry.

2001MY_COROLLA_U (OM12720U)

193

’01 Corolla U (L/O 0005)

Windows The windows may be cleaned with any household window cleaner.

NOTICE

When cleaning the inside of the win- dows, be careful not to scratch or damage the heater wires on the rear window.

Air conditioning control panel, car au- dio, instrument panel, console panel, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly wipe off dirt.

NOTICE

(cid:2) Do not use organic substances (sol- vents, kerosene, alcohol, gasoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.

(cid:2) If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.

(cid:2) If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- tain the ingredients mentioned a- bove. Immediately clean any spill using the method mentioned above.

If you have any questions about the cleaning of your Toyota, your local Toyota dealer will be pleased to answer them.

194

2001MY_COROLLA_U (OM12720U)

’01 Corolla U (L/O 0005)

SECTION 6

VEHICLE MAINTENANCE AND CARE Maintenance requirements General maintenance Does your vehicle need repairing

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

196
197
199

For scheduled maintenance information, please refer to the “Sched- uled Maintenance Guide” or “Owner’s Manual Supplement”.

2001MY_COROLLA_U (OM12720U)

195

’01 Corolla U (L/O 0005)

Maintenance requirements Your Toyota vehicle has been designed for fewer maintenance requirements with long- er service intervals to save both your time and money. However, each regular mainte- nance, as well as day–to–day care, is more important than ever before to ensure smooth, trouble–free, safe, and economical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note that both the new vehicle and emis- sion control system warranties specify that proper maintenance and care must be per- formed. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for complete warranty information. General maintenance General maintenance items are those day– to–day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your Toyota dealer will be pleased to do them at a nominal cost.

196

Scheduled maintenance The scheduled maintenance items listed in the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement” are those required to be serviced at regular inter- vals. For details of your maintenance schedule, read the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non–Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may also elect to have mainte- nance, replacement, or repair of the emission control devices and system performed by any automotive repair es- tablishment or individual without invali- dating this warranty. See “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement” for complete war- ranty information.

for

2001MY_COROLLA_U (OM12720U)

Where to go for service? Toyota technicians are well–trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in–dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your Toyota dealer’s service department performs the best job to meet the maintenance require- ments on your vehicle—reliably and eco- nomically. Your copy of the repair order is proof that all required maintenance has been per- formed for warranty coverage. And if any problems should arise with your vehicle while under warranty, your Toyota dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do–it–yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented in Section 7.

’01 Corolla U (L/O 0005)

If you are a skilled do–it–yourself mechan- ic, the Toyota service manuals are recom- mended. Please be aware that do–it–your- self maintenance can affect your warranty coverage. See “Owner’s Warranty Informa- tion Booklet” or “Owner’s Manual Supple- ment” for the details.

the

items

listed,

General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your Toyota dealer or a quali- fied service shop immediately. It is recom- mended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.

CAUTION

Make these checks only where ade- quate ventilation can be obtained if you run the engine.

to

time

OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Tire pressure Check the pressure with a gauge every two weeks, or at least once a month. See Section 7–2 for additional information.

for

the nuts

Tire surface and wheel nuts Check the tires carefully for cuts, damage or excessive wear. See Section 7–2 for additional information. When checking the tires, make sure no nuts are missing, and check looseness. Tighten them if necessary. Tire rotation Rotate the tires according to the mainte- nance schedule. (For scheduled mainte- nance information, please refer to the sep- arate “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.). See Sec- tion 7–2 for additional information. Fluid leaks Check underneath for leaking fuel, oil, wa- ter or other the vehicle has been parked for a while. If you smell fuel fumes or notice any leak, have the cause found and corrected immediately. Doors and engine hood Check that all doors including trunk lid operate smoothly and all latches lock se- curely. Make sure the engine hood sec- ondary latch secures the hood from open- ing when the primary latch is released. INSIDE THE VEHICLE Items listed below should be checked regularly, e.g. while performing periodic services, cleaning the vehicle, etc.

fluid after