NOTICE
Never tow a vehicle with an automatic transmission from the rear with the front wheels on the ground, as this may cause serious damage the transmission.
to
(b) Using flat bed truck
140
(c) Towing with sling type truck
NOTICE
Do not tow with sling type truck, ei- ther from the front or rear. This may cause body damage.
If towing is necessary, we recommend you to have it done by your authorized Toyota CNG dealer or a commercial tow truck service. If towing service is not available in an emergency, your vehicle may be tempo- rarily towed by a cable or chain se- cured to one of the emergency towing eyelets under the vehicle. Use extreme caution when towing vehicles. A driver must be in the vehicle to steer it and operate the brakes. Towing in this manner may be done only on hard−surfaced roads for a short dis- tance and at the wheels, axles, drive train,steering and brakes must all be in good condition.
low speeds. Also,
CAUTION
CAUTION
If you cannot shift automatic transmission selector lever
If the engine is not running, the pow- er assist for the brakes and steering will not work so steering and braking will be much harder than usual.
Use extreme caution when towing ve- hicles. Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing eyelets and towing cable or chain. The eyelets and towing cable or chain may break and cause serious injury or damage.
NOTICE
Use only a cable or chain specifically intended for use in towing vehicles. Securely fasten the cable or chain to the towing eyelets provided.
Before towing, release the parking brake and put the transmission in “N”. The key must be in “ACC” (engine off) or “ON” (engine running).
though
If you cannot shift the selector lever out of “P” position to other positions even is de- pressed, use the shift lock override but- ton as follows: 1. Turn
the brake pedal
ignition key
the
to “LOCK” the parking
position. Make sure brake is on.
2. Pry up the cover with a flat−bladed
screwdriver or equivalent.
141
in “Keys”
the suggestion given
If you lose your keys Your authorized Toyota CNG dealer can make a new key if you can give them the key number. See Chapter 1−2. If your keys are locked in the vehicle and you cannot get a duplicate, your autho- rized Toyota CNG dealer can still open the door for you, using their special tools. If you must break a window to get in, we suggest breaking the smallest side window because it is the least expensive to re- place. Be extremely cautious to avoid cuts from the glass.
in
If you suspect the fuel is leaking
Open
Close
3. Insert your finger into the hole to push down the shift lock override button. You can shift out of “P” position only while pushing the but- ton.
4. Shift into “N” position. 5. Insert the cover. 6. Start the engine. For your safety,
keep the brake pedal depressed.
Be sure to have the system checked by your authorized Toyota CNG dealer as soon as possible.
142
If you smell fuel or hear the sound of leaking fuel at anytime or if your ve- hicle is involved in an accident, imme- diately close the manual shut off valve to shut the fuel off. The manual shut off valve is intended to shut the fuel from the tank off. Normally it is left open. To close: Turn the lever clockwise 90°. To open: Turn the lever counterclockwise 90°. If you suspect a fuel leakage, close the manual shut off valve and have your ve- hicle serviced by your authorized Toyota CNG dealer as soon as possible. If, due to a collision or similar circum- stances, the fuel system may be dam- aged, close the manual shut off value, and contact your authorized Toyota CNG dealer to have the fuel system checked for fuel leakage.
CAUTION
D If you smell or hear fuel leaking, shut off the fuel system immediate- ly. If leaking fuel is ignited, an ex- plosion or fire could occur, causing death or serious injury.
D Do not
inhale a
large amount of leaked fuel. Inhaling the natural gas continuously may cause the lack of oxygen in your body.
D If you suspect a fuel leakage, do not park the vehicle in an enclosed area such as a garage, or the leaked fuel may fill the area and cause a fire or explosion.
D If you suspect the fuel is leaking while refueling, stop refueling im- mediately. If leaking fuel is ignited, an explosion or fire could occur, causing death or serious injury.
143
144
Part 5
CORROSION
PREVENTION AND
APPEARANCE CARE
D Protecting your Toyota from
corrosion
D Washing and waxing your Toyota D Cleaning the interior
the
Protecting your Toyota from corrosion Toyota, through its diligent research, de- sign and use of the most advanced technology available, has done its part to help prevent corrosion and has provided you with vehicle construction. Now, it is up to you. Proper care of your Toyota can help ensure long− term corrosion prevention. The most common causes of corrosion to your vehicle are: D The accumulation of road salt, dirt and moisture in hard−to−reach areas under the vehicle.
quality
finest
D Chipping of paint, or undercoating caused by minor accidents or by stones and gravel.
Care is especially important if you live in particular areas or operate your ve- hicle under certain environmental condi- tions: D Road salt or dust control chemicals will accelerate corrosion, as will the pres- ence of salt in the air near the sea− coast or in areas of industrial pollution. D High humidity accelerates corrosion es- pecially when temperatures range just above the freezing point.
D Wetness or dampness to certain parts of your vehicle for an extended period of time, may cause corrosion even though other parts of the vehicle may be dry.
those components of
D High temperatures will cause corrosion to the vehicle which are prevented from quick−drying due to lack of proper ventilation.
The above signifies the necessity to keep your vehicle, particularly the underside, as clean as possible and to repair any dam- age to paint or protective coatings as soon as possible. To help prevent corrosion on your Toyota, follow these guidelines: Wash your vehicle frequently. It is, of course, necessary to keep your vehicle clean by regular washing, but to prevent corrosion, the following points should be observed: D If you drive on salted roads
the winter or if you live near the ocean, you should hose off the undercarriage at least once a month to minimize cor- rosion.
in
145
D High pressure water or steam is effec- tive for cleaning the vehicle’s underside and wheel housings. Pay particular attention to these areas as it is difficult to see all the mud and dirt. It will do more harm than good to simply wet the mud and debris without removing them. The lower edge of doors, rocker panels and frame members have drain holes which should not be allowed to clog with dirt as these areas can cause corrosion.
trapped water
in
D Wash the underside of the vehicle thor-
oughly when winter is over.
See “Washing and waxing your Toyota” for more tips. Check the condition of your vehicle’s paint and trim. If you find any chips or scratches in the paint, touch them up im- mediately to prevent corrosion from start- ing. If the chips or scratches have gone through the bare metal, have a qualified body shop make the repair.
146
Check the interior of your vehicle. Wa- ter and dirt can accumulate under the floor mats and could cause corrosion. Oc- casionally check under the mats to make sure the area is dry. Be particularly care- ful when transporting chemicals, cleans- ers, fertilizers, salt, e tc.; these should be transported in proper containers. If a spill or leak should occur, immediately clean and dry the area. Use mud shields on your wheels. If you drive on salted or gravel roads, mud shields help protect your vehicle. Full−size shields, which come as near to the ground as possible, are the best. We recommend that the fittings and the area where the shields are installed be treated to resist corrosion. Your authorized Toyota CNG dealer will be happy to assist in supplying and installing the shields if they are rec- ommended for your area. Keep your vehicle in a well ventilated garage or a roofed place. Do not park your vehicle in a damp, poorly venti- lated garage. If you wash your vehicle in the garage, or if you drive it in covered with water or snow, your garage may be so damp it will cause corrosion. Even if your garage is heated, a wet vehicle can corrode if the ventilation is poor.
Washing and waxing your Toyota Washing your Toyota Keep your vehicle clean by regular washing. The following cases may cause weakness to the paint or corrosion to the body and parts. Wash your vehicle as soon as pos- sible. D When driving in a coastal area D When driving on a road sprinkled with
antifreeze
D When having stuck of coal
tree sap, bird droppings and carcass of an insect
tar,
D When driving in the areas where there is a lot of smoke, soot, dust, iron dust and chemical substance
D When the vehicle becomes remarkably
dirty with dust and mud Hand−washing your Toyota Work in the shade and wait until the vehicle body is not hot to the touch.
CAUTION
When cleaning under floor or chassis, be careful not to injure your hands.
1. Rinse off loose dirt with a hose. Re- move any mud or road salt from the underside of the wheel wells.
the vehicle or
in
2. Wash with a mild car−wash soap, mixed according to the manufacturer’s instructions. Use a soft cotton mitt and keep it wet by dipping it frequently into the wash water. Do not rub hard—let the soap and water remove the dirt.
Plastic bumpers: Wash carefully. Do not scrub with abrasive cleaners. The bumper faces are soft. Road turpentine or cleaners that are marked safe for painted surfaces.
tar: Remove with
NOTICE
Do not use gasoline or strong sol- vents, which may be toxic or cause damage.
3. Rinse
thoroughly—dried
can cause streaking. In hot weather you may need to rinse each section right after you wash it.
soap
4. To prevent water spots, dry the vehicle using a clean soft cotton towel. Do not rub or press hard—you might scratch the paint.
Automatic car wash Your vehicle may be washed in an auto- matic car wash, but remember that the paint can be scratched by some type of brushes, unfiltered washing water, or the washing process itself. Scratching reduces paint durability and gloss, especially on darker colors. The manager of the car wash should be able to advise you wheth- er the process is safe for the paint on your vehicle. Waxing your Toyota Polishing and waxing is recommended to maintain the original beauty of your Toyota’s finish. Once a month or if the vehicle does not repel water well, apply wax.
1. Always wash and dry the vehicle be- fore you begin waxing, even if you are using a combined cleaner and wax.
2. Use a good quality polish and wax. If the finish has become extremely weath- ered, use a car−cleaning polish, fol- lowed by a separate wax. Carefully fol- low the manufacturer’s instructions and precautions. Be sure to polish and wax the chrome trim as well as the paint. the vehicle again when water does not bead but remains on the sur- face in large patches.
3. Wax
NOTICE
Always remove the plastic bumpers if your vehicle is re−painted and placed in a high heat paint waxing booth. High temperatures could damage the bumpers.
147
Cleaning the interior
CAUTION
Do not wash the vehicle floor with water, or allow water to get onto the floor when cleaning the vehicle interi- or or exterior. Water may get into audio components or other electrical components above or under the floor carpet (or mat) and cause a malfunc- tion; and it may cause body corro- sion.
Vinyl interior The vinyl upholstery may be easily cleaned with a mild soap or detergent and water. First vacuum over the upholstery to re- move loose dirt. Then, using a sponge or soft cloth, apply the soap solution to the vinyl. After allowing it to soak in for a few minutes to loosen the dirt, remove the dirt and wipe off the soap with a clean damp cloth. If all the dirt do not come off, re- peat the procedure. Commercial foaming− type vinyl cleaners are also available which work well. Follow the manufacturer’s instructions.
148
NOTICE
NOTICE
Do not use solvent, thinner, gasoline or window cleaner on the interior.
z Do not use dye or bleach on the
belts—it may weaken them.
to
foam−type shampoo
Carpets Use a good clean the carpets. Begin by vacuuming thoroughly to remove as much dirt as possible. Several types of foam cleaners are available; some are in aerosol can sand others are powders or liquids which you mix with water to pro- duce a foam. To shampoo the carpets, use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water—the best results are obtained by keeping the carpet as dry as possible. Read the shampoo instructions and follow them closely. Seat belts The seat belts may be cleaned with mild soap and water or with lukewarm water. Use a cloth or sponge. As you are clean- ing, check the belts for excessive wear, fraying, or cuts.
z Do not use the belts until they be-
come dry.
Windows The windows may be cleaned with any household window cleaner.
NOTICE
When cleaning the inside of the win- dows, be careful not to scratch or damage the heater wires on the rear window.
Air conditioning control panel, car au- instrument panel, c onsole panel, dio, and switches Use a soft damp cloth for cleaning. Soak a clean soft cloth in water or luke- warm water then lightly w ipe off dirt.
NOTICE
z Do not use organic substances (sol- vents, kerosene, alcohol, g asoline, etc.) or alkaline or acidic solutions. These chemicals can cause discol- oring, staining or peeling of the surface.
z If you use cleaners or polishing agents, make sure their ingredients do not include the substances men- tioned above.
z If you use a liquid car freshener, do not spill the liquid onto the ve- hicle’s interior surfaces. It may con- ingredients mentioned a - tain bove. Immediately clean any spill using the method mentioned above.
the
If you have any questions about the cleaning your authorized Toyota CNG dealer will be pleased to answer them.
Toyota,
your
of
149
150
Part 6
VEHICLE
MAINTENANCE
AND CARE
D Maintenance requirements D General maintenance D Does your vehicle need
repairing?
For scheduled maintenance information, please refer to the separate “Owner’s Manual Supplement”.
that both
Maintenance requirements Your Toyota vehicle has been designed to for fewer maintenance requirements with longer service intervals to save both your time and money. However, each regular maintenance, as well as day−to−day care, is more important than ever before to en- sure smooth, trouble−free, safe, and eco- nomical drivings. It is the owner’s responsibility to make sure the specified maintenance, including general maintenance service, is performed. Note the new vehicle and emission control system warranties specify that proper maintenance and care must be performed. Manual Supplement”. General maintenance General maintenance items are those day− to−day care practices that are important to your vehicle for proper operation. It is the owner’s responsibility to insure that the general maintenance items are performed regularly. These checks or inspections can be done either by yourself or a qualified technician, or if you prefer, your authorized Toyota CNG dealer will be pleased to do them at a nominal cost.
“Owner’s
See
the
separate
Scheduled maintenance The scheduled maintenance items listed in the “Owner’s Manual Supplement” are those required to be serviced at regular intervals. For details of your maintenance schedule, read “Owner’s Manual Supplement”. It is recommended that any replacement parts used for maintenance or for the repair of the emission control system be Toyota supplied. The owner may elect to use non−Toyota supplied parts replacement pur- poses without invalidating the emission control system warranty. However, use of replacement parts which are not of equivalent quality may impair the effec- tiveness of the emission control sys- tems. You may have maintenance, replacement, or repair of the control devices and system performed by any automotive repair individual without invalidating this warranty. See “Owner’s Manual Supplement” for complete warranty information.
establishment
emission
elect
also
for
or
to
151
a
you are
If skilled do−it−yourself mechanic, the Toyota service manuals are recommended. Please be aware that do−it−yourself maintenance can affect your warranty coverage. See “Owner’s Manual Supplement” for the details.
Where to go for service? Toyota technicians are well−trained spe- cialists and are kept up to date with the latest service information through technical bulletins, service tips, and in−dealership training programs. They learn to work on Toyotas before they work on your vehicle, rather than while they are working on it. You can be confident that your authorized Toyota CNG dealer’s service department performs the best job to meet the mainte- nance requirements on your vehicle—reli- ably and economically. Your copy of the repair order is proof that all been performed for warranty coverage. And if any problems should arise with your your vehicle while authorized dealer will promptly take care of it. Again, be sure to keep a copy of the repair order for any service performed on your Toyota. What about do−it−yourself maintenance? Many of the maintenance items are easy to do yourself if you have a little mechani- cal ability and a few basic automotive tools. Simple instructions for how to per- form them are presented in Part 7.
required maintenance
under warranty,
Toyota CNG
has
152
the
items
listed,
General maintenance Listed below are the general maintenance items that should be performed as fre- quently as specified. In addition to check- ing if you notice any unusual noise, smell or vibration, you should investigate the cause or take your vehicle to your authorized Toyota CNG dealer or a qualified service shop immedi- ately. It is recommended that any problem you notice be brought to the attention of your dealer or the qualified service shop for their advice.
CAUTION
Make these checks only where ade- quate ventilation can be obtained if you run the engine.
to
time
OUTSIDE THE VEHICLE Items listed below should be performed from time, unless otherwise specified. Tire pressure Check the pressure with a gauge every two weeks, or at least once a month. See Chapter 7−2 for additional information.
for
the nuts
Tire surface and wheel nuts
Check the tires carefully for cuts, damage
or excessive wear. See Chapter 7−2 for
additional information. When checking the
tires, make sure no nuts are missing, and
check
looseness. Tighten
them if necessary.
Tire rotation
Rotate the tires every 12000 km (7500
miles). See Chapter 7−2 for additional in-
formation.
Fluid leaks
Check underneath for leaking oil, water or
other
the vehicle has been
parked for a while. If you smell fuel fumes
or notice any leak, have the cause found
and corrected immediately.
Doors and engine hood
Check that all doors including trunk lid
operate smoothly and all latches lock se-
curely. Make sure the engine hood sec-
ondary latch secures the hood from open-
ing when the primary latch is released.
INSIDE THE VEHICLE
Items listed below should be checked
regularly, e.g. while performing periodic
services, cleaning the vehicle, etc.
fluid after
Lights Make sure the headlights, stop lights, tail lights, turn signal lights, and other lights are all working. Check headlight aim. Service reminder indicators and warning buzzers Check that all service reminder indicators and warning buzzers function properly. Steering wheel Be alert for changes in steering condition, such as hard steering or strange noise. Seats Check that all front seat controls such as seat adjusters, seatback recliner, etc. op- erate smoothly and that all latches lock securely in any position. Check that the head restraints move up and down smoothly and that the locks hold securely in any latched position. Seat belts Check that the seat belt system such as buckles, retractors and anchors operate properly and smoothly. Make sure that the belt webbings not cut, frayed, worn or damaged.
Accelerator pedal Check the pedal for smooth operation and uneven pedal effort or catching. Brake pedal Check the pedal for smooth operation and that the pedal has the proper clearance. Check the brake booster function. Brakes At a safe place, check that the brakes do not pull to one side when applied. Parking brake Check that the lever has the proper travel and that, on a safe incline, your vehicle is held securely with only the parking brake applied. Automatic transmission “Park” mecha- nism Check the lock release button of the se- lector lever for proper and smooth opera- tion. On a safe incline, check that your vehicle is held securely with the selector lever in “P” position and all brakes re- leased.
153
Power steering fluid level Check the level through the reservoir. The level should be in the “HOT” or “COLD” range depending on the fluid temperature. See Chapter 7−2 for additional information. Exhaust system If you notice any change in the sound of the exhaust or smell exhaust fumes, have the cause located and corrected immedi- ately. in Part 2.)
(See engine exhaust cautions
IN THE ENGINE COMPARTMENT
Items listed below should be checked
from time to time, e.g. each time when
refueling.
Washer fluid
Make sure there is sufficient fluid in the
tank. See Chapter 7−3 for additional in-
formation.
Engine coolant level
Make sure the coolant level is between
the “FULL” and “LOW” lines on the see−
through reservoir when the engine is cold.
See Chapter 7−2 for additional information.
Battery electrolyte level
Make sure the electrolyte level of all bat-
tery cells is between upper and lower lev-
el lines on the case. Add only distilled
water when replenishing. See Chapter 7−3
for additional information.
Brake fluid level
Make sure the brake fluid level is correct.
See Chapter 7−2 for additional information.
Engine oil level
Check the level on the dipstick with the
engine turned off and the vehicle parked
on a level spot. See Chapter 7−2 for addi-
tional information.
154
tip−offs
for changes
Does your vehicle need repairing? Be on the alert in perfor- mance, sounds, and visual that indicate service is needed. Some impor- tant clues are as follows: D Engine missing, stumbling, or pinging D Appreciable loss of power D Strange engine noises D A leak under the vehicle (however, wa- ter dripping from the air conditioning after use is normal.)
D Change
in exhaust sound (This may indicate a dangerous carbon monoxide leak. Drive with the windows open and have the exhaust system checked im- mediately.)
D Flat−looking tire; excessive tire squeal
when cornering; uneven tire wear
D Vehicle pulls to one side when driving
straight on a level road
D Strange noises related to suspension
movement
D Loss of brake effectiveness; spongy feeling brake; pedal almost touches floor; vehicle pulls to one side when braking
D Engine coolant temperature continually
higher than normal
If you notice any of these clues, take your vehicle to your authorized Toyota CNG dealer as soon as possible. It probably needs adjustment or repair.
CAUTION
Do not continue driving with the ve- hicle unchecked. It could result in se- rious vehicle damage and possibly personal injury.
155
156
Part 7
DO−IT−YOURSELF
MAINTENANCE—
Chapter 7−1
Introduction
D Engine compartment overview D Fuse locations D Do−it−yourself service
precautions
D Parts and tools
157
Engine compartment overview
1. Power steering fluid reservoir 2. Engine coolant reservoir 3. Engine oil filler cap 4. Engine oil level dipstick 5. Brake fluid reservoir 6. Fuse blocks 7. Battery 8. Electric cooling fans 9. Windshield washer fluid tank
158
Fuse locations
Spare fuses
159
Do−it−yourself service precautions If you perform maintenance by yourself, be sure to follow the correct procedure given in this part. You should be aware that improper or in- complete servicing may result in operating problems. Performing do−it−yourself maintenance during the warranty period may affect your warranty coverage. Read the separate Toyota Warranty statement for details and suggestions. This part gives instructions only for those items that are relatively easy for an owner to perform. As explained in Part 6, there are still a number of items that must be done by a qualified technician with special tools. For information on tools and parts for do− it−yourself maintenance, see “Parts and tools”. Utmost care should be taken when work- ing on your vehicle to prevent accidental injury. Here are a few precautions that you should be especially careful to ob- serve:
160
CAUTION
D Never work on the fuel system by yourself. Any work on this system must be performed by your autho- rized Toyota CNG dealer. If an un- qualified person works on it incor- rectly causing fuel leaks etc., a fire hazard or explosion may occur, which is very dangerous.
D When the engine is running, keep tools away hands, clothing, and from the moving fan and engine drive rings, watches, and ties is advisable.)
(Removing
belts.
D Right after driving,
the engine compartment—the engine, radiator, exhaust manifold and spark plug boots, etc.—will be hot. So be care- ful not to touch them. Oil, fluids and spark plugs may also be hot.
D If the engine is hot, do not remove the radiator cap or loosen the drain plugs to prevent burning yourself.
D Do not smoke, cause sparks or al- low open flames around fuel or the battery. Their fumes are flammable.
D Be extremely cautious when work- ing on the battery. It contains poi- sonous and corrosive sulfuric acid. D Do not get under your vehicle with just the body jack supporting it. Al- ways use automotive jack stands or other solid supports.
D Be sure that the ignition is off if you work near the electric cooling fans or radiator grille. With the ignition on, the electric cooling fans will automatically start to run if the engine coolant temperature is high and/or the air conditioning is on.
D Use eye protection whenever you work on or under your vehicle where you may be exposed to flying or falling material, fluid spray, etc. D Used engine oil contains potentially harmful contaminants which may cause skin disorders such as in- flammation or skin cancer, so care should be taken to avoid prolonged and repeated contact with it. To re- move used engine oil from your thoroughly with soap skin, wash and water.
z Use only spark plugs of the speci- fied type. Using other types will cause engine damage, loss of per- formance or radio noise.
z Do not reuse platinum−tipped spark
plugs by cleaning or regapping.
z Do not overfill automatic transmis- transmission
fluid, or
the
sion could be damaged.
z Do not drive with the air cleaner filter removed, or excessive engine wear could result. Also backfiring could cause a fire in the engine compartment.
z Be careful not to scratch the glass
surface with the wiper frame.
z When closing
the engine hood, check to see that you have not for- gotten any tools, rags, etc.
D Do not
leave used oil within the
reach of children.
D Dispose of used oil and filter only in a safe and acceptable manner. Do not dispose of used oil and fil- ter in household trash, in sewers or onto the ground. Call your autho- rized Toyota CNG dealer or a ser- vice station information con- cerning recycling or disposal.
for
NOTICE
z Remember that battery and ignition cables carry high currents or volt- ages. Be careful of accidentally causing a short circuit.
z Be careful not to touch the fuel pipe unintentionally. If an excessive force is applied on the pipe, gas may leak from its connections.
z Add only demineralized or distilled water to fill the radiator. And if you spill some of the coolant, be sure to wash off with water to prevent it from damaging the parts or paint.
z Do not allow dirt or anything else to fall through the spark plugholes.
Parts and tools Here is a list of parts and tools you will need on performing do−it−yourself mainte- nance. Remember all Toyota parts are de- signed in metric sizes, so your tools must be metric. Checking the engine oil level Parts (if level is low): API D Engine
grade SJ, “Energy−Conserving” or ILSAC multi- grade having viscosity proper for your climate
oil
Tools: D Rag or paper towel D Funnel (only for adding oil) Checking the engine coolant level Parts (if level is low): D “TOYOTA Long Life Coolant” or equiva-
lent See Chapter 7−2 for details about cool- ant type selection.
D Demineralized or distilled water Tools: D Funnel (only for adding coolant)
161
Checking and replacing fuses Parts (if replacement is necessary): D Genuine Toyota fuse or equivalent with
same amperage rating as original
Adding washer fluid Parts: D Water D Washer fluid containing antifreeze (for
winter use)
Tools: D Funnel Replacing light bulbs Parts: D Bulb with same number and wattage rating as original (See charts in “Re- placing light bulbs” in Chapter 7−3.)
fluid
Tools: D Screwdriver D Flat−bladed screwdriver
terminal
Checking brake fluid
Parts (if level is low):
D SAE J1703 or FMVSS No.116 DOT 3
brake fluid
Tools: D Rag or paper towel D Funnel (only for adding fluid) Checking power steering fluid Parts (if level is low): D Automatic
transmission
DEXRON®II or III
Tools: D Rag or paper towel D Funnel (only for adding fluid) Checking battery condition Tools: D Warm water D Baking soda D Grease D Conventional wrench
(for
clamp bolts)
162
Part 7
DO−IT−YOURSELF
MAINTENANCE—
Chapter 7−2
Engine and Chassis
D Checking the engine oil level D Checking the engine coolant
level
D Checking brake fluid D Checking power steering fluid D Checking tire pressure D Checking and replacing tires D Rotating tires D Installing snow tires and chains D Replacing wheels
Checking the engine oil level
Low level
Full level
Add oil
O.K.
Too full
With the engine at operating tempera- ture and turned off, check the oil level on the dipstick. 1. To get a
the vehicle should be on a level spot. After turning off the engine, wait a few minutes for the oil to drain back into the bottom of the engine.
reading,
true
2. Pull out the dipstick, and wipe it clean
with a rag.
3. Reinsert the dipstick—push it in as far as it will go, or the reading will not be correct.
4. Pull the dipstick out and look at the oil
level on the end.
CAUTION
Be careful not to touch the hot ex- haust manifold.
If the oil level is below or only slightly above the low level line, add engine oil of the same type as already in the en- gine. Remove the oil filler cap and add engine oil in small quantities at a time, checking the dipstick. The approximate quantity of oil needed to fill between the low level and the full level on the dipstick is indicated below for ref- erence. When the level reaches within the correct range, install the filler cap hand−tight. Oil quantity, L (qt., lmp. qt.):
0.7 (0.7, 0.6)
NOTICE
z Avoid overfilling, or
the engine
could be damaged.
z Check the oil level on the dipstick
once again after adding the oil.
163
Oil identification marks Either or both API registered marks are added to some oil containers to help you select the oil you should use. The API Service Symbol is located any- where on the outside of the container. The top portion of the label shows the oil quality by API (American Petroleum Insti- tute) designations such as SJ. The center portion of the label shows the SAE viscos- ity grade such as SAE 5W−30. “Energy− Conserving” shown in the lower portion, indicates that the oil has fuel−saving ca- pabilities. The ILSAC (International Lubricant Stan- dardization and Approval Committee) Certi- fication Mark is displayed on the front of the container.
Engine oil selection Use API grade SJ, “Energy−Conserving” or ILSAC multigrade engine oil. Recommended viscosity (SAE):
API service symbol
for good
SAE 5W−30 is the best choice for your vehicle, fuel economy, and good starting in cold weather. If you use SAE 10W−30 engine oil in extremely low temperatures, the engine may become difficult to start, so SAE 5W−30engine oil is recommended.
164
ILSAC certification mark
Checking the engine coolant level Look at the see−through coolant reser- voir when the engine is cold. The cool- ant level is satisfactory if it is between the “FULL” and “LOW” lines on the reservoir. If the level is low, add ethyl- ene−glycol type coolant for a proper corrosion protection of aluminum com- ponents. The coolant level in the reservoir will vary with engine temperature. However, if the level is on or below the “LOW” line, add coolant. Bring the level up to the “FULL” line. Always use ethylene−glycol type coolant for a proper corrosion protection of alumi- num components. See information in the next column. If the coolant level drops within a short time after replenishing, there may be a leak the radiator, hoses, radiator cap and drain cock and water pump. If you can find no leak, have your autho- rized Toyota CNG dealer the cap pressure and check for leaks in the cool- ing system.
the system. Visually check
test
in
CAUTION
To prevent burning yourself, do not remove the radiator cap when the en- gine is hot.
that
Coolant type selection Use of improper coolants may damage your engine cooling system. Your coolant must contain ethylene−glycol type coolant for a proper corrosion protection of your engine aluminum contains components. Use “TOYOTA Long Life Coolant” or equivalent. freezing and In addition subsequent damage this type of coolant will also prevent corrosion. Further supplemental inhibitors or additives are neither needed nor recommended. Read the coolant container for information on freeze protection. Follow the manufac- turer’s directions to mix with plain water (preferably demineralized water or distilled water). The total capacity of the cooling system is given in Part 8.
for how much
to preventing
the engine,
to
We recommend to use 50% solution for your Toyota, to provide protection down to about −35_C (−31_F). When it is extreme- ly cold, to about −50°C (−58°F), 60% solution is rec- ommended. Do not use more than 70% solution for better coolant performance.
to provide protection down
NOTICE
Do not use alcohol type antifreeze or plain water alone.
165
Checking brake fluid
Checking power steering fluid
Use only newly opened brake fluid. Once opened, brake fluid absorbs moisture from the air, and excess moisture can cause a dangerous loss of braking.
CAUTION
Take care when filling the reservoir because brake fluid can harm your eyes and damage painted surfaces. If fluid gets in your eyes, flush your eyes with clean water.
NOTICE
If you spill some of the fluid, be sure to wash it off with water to prevent it from damaging the parts or paint.
reservoir. The
To check the fluid level, simply look at the see−through level should be between the “MAX” and “MIN” lines on the reservoir. It is normal for the brake fluid level to go down slightly as the brake pads wear. So be sure to keep the reservoir filled. If the reservoir needs frequent refilling, it may indicate a serious mechanical prob- lem. If the level is low, add SAE J1703 or FMVSS No.116 DOT 3 brake fluid to the brake reservoir. Remove and replace the reservoir cover by hand.
166
Open
If cold O.K.
If cold add
If hot O.K.
Close
If hot add
III.
Check the fluid level through the reser-
voir. If necessary, add automatic trans-
mission fluid DEXRONrII or
If the vehicle has been driven around 80
km/h (50 mph)
for 20 minutes (a little
more in frigid temperatures), the fluid is
hot (60_C—80_C or 140_F—175_F). You
may also check the level when the fluid
is
temperature,
10_C—30_C or 50_F—85_F) if the engine
has not been run for about five hours.
(about
room
cold
Clean all dirt from outside of the reservoir tank and look at the fluid level. If the fluid is cold, the level should be in the “COLD” range. Similarly, if it is hot, the fluid level should be in the “HOT” range. If the level is at the low side of either range, add automatic fluid DEXRONrII or III to bring the level within the range. To remove the filler cap, turn it counter- clockwise and lift up. To reinstall it, turn it clockwise. After replacing the filler cap, visually check the steering box case, vane pump and hose connections for leaks or damage.
transmission
CAUTION
The reservoir tank may be hot so be careful not to burn yourself.
NOTICE
Avoid overfilling, or the power steer- ing could be damaged.
Checking tire pressure
Keep your tire pressures at the proper level. The recommended cold tire pressures, tire size and the vehicle capacity weight are given in Part 8. They are also on the tire pressure label as shown. You should check the tire pressures every two weeks, or at least once a month. And don’t forget the spare! Incorrect tire pressure can reduce tire life and make your vehicle less safe to drive.
the
results
tire pressure
tire pressure
is excessively
Low
in excessive
wear, poor handling, reduced fuel econo-
my, and the possibility of blowouts from
overheated tires. Also, low tire pressure
can cause poor sealing of the tire bead.
If
low,
there is the possibility of wheel deforma-
tion and/or tire separation.
High tire pressure produces a harsh ride,
handling problems, excessive wear at the
center of
the tire tread, and a greater
possibility of tire damage from road haz-
ards.
If a tire frequently needs refilling, have it
checked by your authorized Toyota CNG
dealer.
The following instructions for checking
tire pressure should be observed:
D The pressure should be checked only
when the tires are cold. If your ve-
hicle has been parked for at least 3
hours and has not been driven
for
more than 1.5 km or 1 mile since, you
will get an accurate cold tire pressure
reading.
D Always use a tire pressure gauge. The appearance of a tire can be mis- leading. Besides, that are even just a few pounds off can degrade handling and ride.
tire pressures
167
D Take special care when adding air to the compact spare tire. The smaller tire size can gain pressure very quick- ly. Add compressed air in small quanti- ties and check the pressure often until it reaches the specified pressure.
D Do not bleed or reduce tire pressure after driving. It is normal for the tire pressure to be higher after driving.
D Never exceed
the vehicle capacity weight. The passenger and luggage weight should be located so that the vehicle is balanced.
D Be sure to reinstall the tire inflation valve caps. Without the valve caps, dirt or moisture could get into the valve core and cause air leakage. If the caps have been lost, have new ones put on as soon as possible.
168
Checking and replacing tires
Tread wear indicator
CHECKING YOUR TIRES
Check the tires tread for the tread wear
indicators. If the indicators show, re-
place the tires.
The
tires on your Toyota have built−in
tread wear indicators to help you know
when the tires need replacement. When
the tread depth wears to 1.6 mm (0.06
in.) or less, the indicators will appear. If
you can see the indicators in two or more
adjacent grooves, the tire should be re-
placed. The lower the tread, the higher
the risk of skidding.
The effectiveness of snow tires is lost
if the tread wears down below 4 mm
(0.16 in.).
Check the tires regularly for damage such as cuts, splits and cracks. If any damage is found, consult with a techni- cian and have the tire repaired or re- placed. Even if the damage does not appear seri- ous, a qualified technician should examine the damage. Objects which have pene- trated the tire may have caused internal damage. Any tires which are over 6 years old must be checked by a qualified techni- cian even if damage is not obvious. Tires deteriorate with age even have never or seldom been used. This applies also to the spare tire and tires stored for future use. REPLACING YOUR TIRES When replacing a tire, use only the same size and construction as original- ly installed and with the same or great- er load capacity. Using any other size or type of tire may seriously affect handling, ride, speedome- ter/odometer calibration, ground clearance, and clearance between the body and tires or snow chains.
they
if
Rotating tires
CAUTION
D Do not mix radial, bias belted, or bias−ply tires on your vehicle. It can cause dangerous handling char- acteristics, resulting in loss of con- trol.
CAUTION
Do not include a compact spare tire when rotating the tires. It is designed for temporary use only.
D Do not use tires or wheels other recom-
the manufacturer’s
than mended size.
tire
Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See “If you have a flat tire” in Part 4 for tire change procedure. When a is replaced, should always be balanced. An unbalanced wheel may affect vehicle handling and tire life. Wheels can get out of balance with regular use and should therefore be balanced occasionally. When replacing a tubeless tire, the air valve should also be replaced with a new one.
the wheel
To equalize the wear and help extend tire life, Toyota recommends that you rotate your tires approximately every 12000 km (7500 miles). However, the most appropriate timing for tire rotation may vary according to your driving hab- its and road surface conditions. See “If you have a flat tire” in Part 4 for tire change procedure. When for uneven wear and damage. Abnormal wear is usu- ally caused by incorrect tire pressure, im- proper wheel alignment, out−of−balance wheels, or severe braking.
tires, check
rotating
169
Installing snow tires and chains WHEN TO USE SNOW TIRES OR CHAINS Snow tires or chains are recommended when driving on snow or ice. On wet or dry roads, conventional tires provide better traction than snow tires. SNOW TIRE SELECTION If you need snow tires, select the same size, construction and load capacity as the original tires on your Toyota. Do not use tires other than those men- tioned above. Do not install studded tires without first checking local regulations for possible restrictions. SNOW TIRE INSTALLATION Snow tires should be installed on all wheels. Installing snow tires on the front wheels only can lead to an excessive difference in road grip capability between the front and rear tires which could cause loss of vehicle control. When storing removed tires you should store them in a cool dry place. Mark the direction of rotation and be sure to install them in the same direction when replac- ing.
170
CAUTION
D Do not drive with the snow tires
incorrectly inflated.
D Never drive over 120 km/h (75 mph)
with any type of snow tires.
TIRE CHAIN SELECTION Use the tire chains of correct size and type. Use SAE Class “S” type radial tire chains except radial cable chains or V−bar type chains. Regulations regarding the use of tire chains vary according to location or type of road, so always check them before installing chains. CHAIN INSTALLATION Install the chains on the front tires as tightly as possible. Do not use tire tires. Retighten chains on chains after km (1/4—1/2 mile). When installing chains on your tires, care- fully follow the instructions of the chain manufacturer.
rear driving
0.5—1.0
the
If wheel covers are used, they will be scratched by the chain band,so remove the covers before putting on the chains.
CAUTION
D Do not exceed 50 km/h (30 mph) or recom- is
the chain manufacturer’s mended speed lower.
limit, whichever
D Drive carefully avoiding bumps, holes, and sharp turns, which may cause the vehicle to bounce.
D Avoid sharp turns or locked−wheel braking, as use of chains may ad- versely affect vehicle handling.
NOTICE
Do not attempt to use a tire chain on the compact spare tire, as it may re- sult in damage to the vehicle as well as the tire.
Replacement with used wheels is not rec- ommended as they may have been sub- jected to rough treatment or high mileage and could fail without warning. Also, bent wheels which have been straightened may have structural damage and therefore should not be used. Never use an inner tube in a leaking wheel which is designed for a tubeless tire.
Replacing wheels WHEN TO REPLACE YOUR WHEELS If you have wheel damage such as bending, cracks or heavy corrosion, the wheel should be replaced. If you fail to replace damaged wheels, the tire may slip off the wheel or they may cause loss of handling control. WHEEL SELECTION When replacing wheels, care should be taken to ensure that the wheels are re- placed by ones with the same load ca- pacity, diameter, rim width, and offset. This must be observed on compact spare tires, too. Correct replacement wheels are available at your authorized Toyota CNG dealer. A wheel of a different size or type may adversely affect handling, wheel and bear- ing life, brake cooling, speedometer/odom- eter calibration, stopping ability, headlight aim, bumper height, vehicle ground clear- ance, and tire or snow chain clearance to the body and chassis.
171
172
Part 7
DO−IT−YOURSELF
MAINTENANCE—
Chapter 7−3
Electrical components
D Checking battery condition D Battery recharging precautions D Checking and replacing fuses D Adding washer fluid D Replacing light bulbs
Checking battery condition— —Precautions
CAUTION
BATTERY PRECAUTIONS The battery produces flammable and explosive hydrogen gas. D Do not cause a spark from the bat-
tery with tools.
D Do not smoke or light a match near
the battery.
The electrolyte contains poisonous and corrosive sulfuric acid. D Avoid contact with eyes, skin or
clothes.
D Never ingest electrolyte. D Wear protective safety glasses when
working near the battery.
D Keep children away from the bat-
tery.
D If electrolyte gets on your skin, thoroughly wash the contact area. If you feel pain or burning, get medi- cal attention immediately.
D If electrolyte gets on your clothes, there is a possibility of its soaking through to your skin, so immediate- ly take off the exposed clothing and follow the procedure above, if nec- essary.
D If you happen to swallow electro- lyte, drink a large quantity of water or milk. Follow with milk of magne- sia, beaten raw egg or vegetable oil. Then go immediately for emer- gency help.
EMERGENCY MEASURES D If electrolyte gets
in your eyes, flush your eyes with clean water immediately immediate medical attention. If possible, con- tinue to apply water with a sponge or cloth while en route to the medi- cal office.
and get
173
—Checking battery exterior
—Checking battery fluid
Terminals
Ground cable
NOTICE
z Be sure the engine and all accesso- ries are off before performing main- tenance.
z When checking the battery, remove the ground cable from the negative terminal (“−” mark) first and rein- stall it last.
z Be careful not to cause a short cir-
cuit with tools.
z Take care no solution gets into the
battery when washing it.
Hold−down clamp
Check the battery for corroded or loose terminal connections, cracks, or loose hold−down clamp. a. If the battery is corroded, wash it off with a solution of warm water and bak- ing soda. Coat the outside of the termi- nals with grease to prevent further cor- rosion.
b. If the terminal connections are loose, their clamp nuts—but do not
tighten overtighten.
c. Tighten
the hold−down clamp only enough to keep the battery firmly in place. Overtightening may damage the battery case.
174
Type A
Green
Dark
Clear or
light yel-
low
Type B
Blue
White
Red
CHECKING BY THE HYDROMETER Check the battery condition by hydrometer color.
the
Hydrometer color
Type A
Type B
GREEN
BLUE
Condition
Good
DARK
WHITE
CLEAR or LIGHT YELLOW
RED
Charging necessary. Have battery checked by your authorized Toyota CNG dealer.
Have battery checked by your authorized Toyota CNG dealer.
Battery recharging precautions During recharging, the battery is pro- ducing hydrogen gas. Therefore, before recharging: 1. If recharging with the battery installed on the vehicle, be sure to disconnect the ground cable.
2. Be sure the power switch on the re- charger the charger cables to the battery and when disconnecting them.
is off when connecting
Checking and replacing fuses
Type A
Good
Blown
CAUTION
Type B
D Always charge the battery in an un- confined area. Do not charge the battery in a garage or closed room where there is not sufficient ventila- tion.
D Only do a slow charge (5 A or less). Charging at a quicker rate is dangerous. The battery may ex- plode, causing personal injuries.
NOTICE
Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.
Good
Blown
Type C
Good
Blown
If the headlights or other electrical components do not work, check the fuses. If any of the fuses are blown, they must be replaced. See “Fuse locations” in Chapter 7−1 for locations of the fuses. Turn the ignition switch and inoperative component off. Pull a suspected fuse straight out and check it. Determine which fuse may be causing the problem. The lid of the fuse box shows the name of the circuit for each fuse. See Part 8 of this manual for the functions controlled by each circuit.
175
the new
If fuse immediately blows out, there is a problem with the electrical sys- tem. Have your authorized Toyota CNG dealer correct it as soon as possible.
CAUTION
Never use a fuse with a higher am- perage rating, or any other object, in place of a fuse. This may cause ex- tensive damage and possibly a fire.
Adding washer fluid If any washer does not work or low windshield washer fluid level warning light comes on, the washer tank may be empty. Add washer fluid. You may use plain water as washer fluid. in cold areas where tempera- However, tures freezing point, use fluid containing antifreeze. This washer product is available at your authorized Toyota CNG dealer and most auto parts stores. Follow the manufacturer’s direc- tions for how much to mix with water.
range below
NOTICE
Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.
can
you
Type A fuses can be pulled out by the pull−out tool. The location of the pull−out tool is shown in the illustration. If you are not sure whether the fuse has blown, try replacing the suspected fuse with one that you know is good. If the fuse has blown, push a new fuse into the clip. Only install a fuse with the amperage rat- ing designated on the fuse box lid. If you do not have a spare fuse, in an emergency the “A/C” “MIRROR−HEATER”, fuse, which may be dispensable for normal driving, and use it if its amperage rating is the same. If you cannot use one of the same amper- age, use one that is lower,but as close as possible to, the rating. If the amperage is lower than that specified, the fuse might blow out again but this does not indicate anything wrong. Be sure to get the correct fuse as soon as possible and return the substitute to its original clip. It is a good idea to purchase a set of spare fuses and keep them in your ve- hicle for emergencies.
“DOME” or
pull
out
176
following
illustrations show how
Replacing light bulbs— The to gain access to the bulbs. When replacing a bulb, make sure the ignition switch and light switch are off. Use bulbs with the wattage ratings given in the table.
CAUTION
Halogen bulbs have pressurized gas inside and require special handling. They can burst or shatter if scratched or dropped. Hold a bulb only by its plastic or metal case. Do not touch the glass part of a bulb with bare hands.
NOTICE
Only use a bulb of the listed type.
60/55
— 27/8
Light bulbs
Headlights
Bulb
No.
HB2
Parking, front side
marker and front
turn signal lights
Rear side marker
lights
Rear turn signal
lights
Stop and tail lights 3157
3156
194
Tail light
Back−up lights
904
921
License plate lights —
3.8