Download PDF Manual

Part 1
OPERATION OF INSTRUMENTS AND CONTROLS—


Chapter 1−1
Overview of instruments and controls


D Instrument panel overview D Instrument cluster overview D Indicator symbols on the


instrument panel


Instrument panel overview


1. Side defroster outlets 2. Side vents 3. Instrument cluster 4. Center vents 5. Glove box 6. Garage door opener box or


miscellaneous box


7. Power door lock switches 8. Power window switches 9. Cup holders 10. Cup holder or rear ashtray 11. Parking brake lever 12. Automatic transmission selector lever 13. Auxiliary box 14. Hood lock release lever 15. Window lock switch


1. Power rear view mirror control switch 2. Headlight and turn signal switch 3. Wiper and washer switches 4. Clock 5. Emergency flasher switch 6. Car audio 7. Rear window and outside rear view


mirror defoggers switch 8. Air conditioning controls 9. Front ashtray 10. Power outlet 11. Cigarette lighter 12. Ignition switch 13. Cruise control switch 14. Tilt steering lock release lever 15. Instrument panel light control knob


Instrument cluster overview


1. Engine coolant temperature gauge 2. Service reminder indicators and


indicator lights


3. Fuel gauge


4. Speedometer 5. Odometer and two trip meters 6. Tachometer


7. Trip meter reset knob 8. Low fuel level warning light


Indicator symbols on the instrument panel


Brake system warning light∗1


Low windshield washer fluid level warning light∗1


Seat belt reminder light∗1


Discharge warning light∗1


Malfunction indicator lamp∗1


Turn signal indicator lights


Headlight high beam indicator light


Overdrive−off indicator light


Low oil pressure warning light∗1


Cruise control indicator light∗2


Anti−lock brake system warning light∗1


Automatic transmission indicator lights


Open door warning light∗1


Rear light failure warning light∗1


SRS warning light∗1


∗1: For details, see “Service reminder indicators and warning


buzzers” in Chapter 1−5.


∗2: If this light flashes, see “Cruise control” in Chapter 1−6.


6


Part 1
OPERATION OF INSTRUMENTS AND CONTROLS—


Keys


Chapter 1−2
Keys and Doors


D Keys D Side doors D Power windows D Trunk lid D Hood D Refueling


Your vehicle is supplied with two kinds of key. 1. Master key—This key works in every


lock.


2. Sub key—This key will not work in the


glove box and trunk.


To protect things locked in the glove box or trunk when you have your vehicle parked, leave the sub key with the atten- dant. Since lid can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the ve- hicle.


the doors and


trunk


KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by your authorized Toyota CNG dealer using the key number. We recommend you to write down the key number and keep it in safe place.


Side doors


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. All lock and unlock simulta- neously with either front door. In the driv- er’s door lock, turning the key once will unlock the driver’s door and twice in suc- cession will unlock all the doors simulta- neously.


the doors


LOCKING AND UNLOCKING WITH INSIDE LOCK BUTTON Move the lock button. To lock: Push the knob forward. To unlock: Pull the knob backward. Closing the door with the lock knob in the lock position will also lock the door. Be careful not to lock your keys in the ve- hicle. The door cannot be locked if you leave the key in the ignition switch.


Driver’s side


Passenger’s side


LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch on the front side. To unlock: Push the switch on the rear side. All the doors lock or unlock simultaneous- ly.


CAUTION


Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident. It also helps prevent the doors from being opened unintentionally.


to


the


lock


lever


the “LOCK”


REAR DOOR CHILD−PROTECTORS Move position as shown on the label. This feature allows you to lock a rear door so it can be opened from the outside only, not from inside. We recommend us- ing this feature whenever small children are in the vehicle.


Power windows


Window lock switch


Automatic operation (to open only): Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it.


The windows can be operated with the switch on each door. The power windows work when the ignition switch is in the “ON” position. Key off operation: If both front doors are closed, they work for 45 seconds even after the ignition switch is turned off. They stop working when either is opened. OPERATING THE DRIVER’S WINDOW Use the switch on the driver’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Pull up the switch.


front door


10


THE


PASSENGERS’


OPERATING WINDOWS Use the switches on the passengers’ doors. The driver’s door also has switches that control the passengers’ windows. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, the passengers’ windows cannot be operated.


CAUTION


To avoid serious personal injury, you must do the following. D Always make sure the head, hands and other parts of the body of all occupants are kept completely in- side the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, be sure that they operate the windows safe- ly.


D When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.


them


D Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power window switches and in a window. Unat- get tended children can become in- volved in serious accidents.


trapped


Trunk lid—


“Luggage stowage precautions”


To open the trunk lid from the outside, insert the master key and turn it clock- wise. in See Part 2 for precautions to observe for load- ing luggage. To close the trunk lid, lower it and press down on it. After closing the trunk lid, try pulling it up to make sure it is securely closed.


11


—Lock release lever


—Luggage security system


CAUTION


Keep the trunk lid closed while driv- ing. This not only keeps the luggage from being thrown out but also pre- vents exhaust gases from entering the vehicle.


To open the trunk lid from the driver’s seat, pull up on the lock release lever.


This system deactivates the lock re- lease lever so that things locked in the trunk can be protected. After closing the trunk lid, insert the master key and turn it counterclockwise to deactivate the lock release lever. After closing the trunk lid, try pulling it up to make sure it is securely locked.


12


Hood


To open the hood: 1. Pull the hood lock release lever. The


hood will spring up slightly.


CAUTION


Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.


2. In front of the vehicle, pull up the the


lever and


lift


auxiliary catch hood.


3. Hold the hood open by inserting the


support rod into the slot.


Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood make sure it If necessary, press down gently on the front edge to lock it.


the support rod


into place.


locks


to


CAUTION


After inserting the support rod into the slot, make sure the rod supports the hood securely from falling down on to your head or body.


13


CAUTION


D In order to safety refuel and avoid serious personal the CNG station staff to refuel the ve- hicle with CNG for you.


injury, ask


D Do not start the engine while refuel- ing. As the natural gas is flam- mable, an explosion or a fire could occur. Also, do not smoke or allow open flames when refueling. D If you smell or hear fuel


leaking while refueling, immediately stop re- fueling. Do not refuel it until after the leak has been repaired.


—Refueling method (high speed refueling)


There are two ways of natural gas re- fueling: high and low speed. This manu- al explains typical high speed refueling. As for the low speed refueling method, follow the manufacturer for the refueling equipments. 1. To open the refueling plug door, pull


instructions provided by


the


the lever up. When refueling, turn off the engine.


that


meets


Refueling— —Refueling precaution When refueling, you must use a special nozzle ANSI/AGA NGV−1−1994 standards. There are three types of nozzles. Use a P36 type nozzle for this vehicle. If a P36 nozzle is not available at a nearby CNG station, you may use another type of nozzle, but you cannot expect to get a completely full tank with it. For your safety, ask and follow the in- structions at the refueling station when refueling. Before starting to refuel, wipe off mud or dirt that may be deposited around the fuel receptacle. You will hear a chattering noise from the tank when it is being filled, but this is quite normal. If you hear fuel leaking from the fuel re- ceptacle, stop refueling immediately and have your authorized Toyota CNG dealer check the fuel receptacle. For information on CNG stations, refer to the station “Refueling station information” on page iii in the beginning of this manu- al.


14


2. Remove the rubber cap. Check there is no mud or dirt around the fuel receptacle.


3. Fit the filling nozzle securely on the


fuel receptacle.


There are various types of filling nozzles so follow the instructions at each CNG station.


4. Turn the valve


lever to fasten the nozzle to the fuel receptacle and to start filling the tank.


15


5. Refueling will stop automatically when the tank is full. When discon- necting the filling nozzle, follow the instructions of the refueling station. Reverse the procedure to disconnect the nozzle after filling the tank. When disconnecting the filling nozzle, you may hear a brief hissing sound as a small amount of fuel escapes, but this is nor- mal.


16


Part 1
OPERATION OF INSTRUMENTS AND CONTROLS—


Chapter 1−3
Seats, Seat belts, Steering wheel and Mirrors


D Seats D Front seats D Head restraints D Seat belts D SRS driver and front passenger


airbags


D Child restraint D Tilt steering wheel D Outside rear view mirrors D Anti−glare inside rear view


mirror


D Sun visors


Seats While the vehicle is being driven, all ve- hicle occupants should have the seatback upright, sit well back in the seat and prop- erly wear the seat belts provided.


Front seats— —Seat adjustment precautions Adjust the driver’s seat so that the foot pedals, steering wheel and instrument panel controls are within easy reach of the driver.


CAUTION


CAUTION


D Do not drive the vehicle unless the occupants are properly seated. Do top of a not allow sitting on folded−down seatback, or the luggage compartment. Persons not properly seated and not properly re- strained by seat belts can be se- verely injured in the event of emer- gency braking or a collision.


in


D During driving, do not allow pas- to stand up or move sengers around between seats. Severe inju- ries can occur in the event of emer- gency braking or a collision.


D Adjustments should not be made while the vehicle is moving, as the seat may unexpectedly move and cause the driver to lose control of the vehicle.


D When adjusting the seat, be careful not to hit the seat against a pas- senger or luggage.


D After adjusting the seat position, try sliding it forward and backward to make sure it is locked in posi- tion.


D After adjusting the seatback, exert body pressure to make sure it is locked in position.


D Do not put objects under the seats. The objects may interfere with the seat−lock mechanism or unexpect- edly push up the seat position ad- justing lever; the seat may suddenly move, causing the driver to lose control of the vehicle.


17


—Adjusting front seats


D While adjusting the seat, do not put your hands under the seat or near the moving parts. You may catch and injure your hands or fingers.


18


1. SEAT POSITION ADJUSTING LEVER Pull the lever up. Then slide the seat to the desired position with slight body pressure and release the lever. 2. SEATBACK


ADJUSTING


ANGLE


LEVER


lever up. lean back to the desired angle


Lean forward and pull the Then and release the lever.


CAUTION


To reduce the risk of sliding under the lap belt during a collision, avoid reclining the seatback any more than needed. The seat belts provide maxi- mum protection in a frontal or rear collision when the driver and the pas- senger are sitting up straight and well back If you are reclined, the lap belt may slide past your hips and apply restraint forces directly to the abdomen. Therefore, in the event of a frontal collision, the risk of personal injury may increase with increasing recline of the seat- back.


in the seats.


3. SEAT CUSHION HEIGHT ADJUSTING


KNOB


Turn the knob either way.


Head restraints


Front


Rear


For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. Front head restraint only—You can also move the head restraint forward or back- ward. If such adjustment is desired, pull or push on the top of the head restraint. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.


CAUTION


D Adjust the center of the head re- straint so that it is closest to the top of your ears.


D After adjusting the head restraint, make sure it is locked in position. the head re-


D Do not drive with


straints removed.


19


Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” for details. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.


20


Do not allow the child to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also, do not let the child sit on your lap. It does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendations.


recommendations. The


CAUTION


the vehicle


in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: D Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. D Avoid reclining the seatbacks too much. The seat belts provide maxi- mum protection when the seatbacks are in the upright position. (Refer to the seat adjustment instructions.) D Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or doors.


D Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.


—Front seat belts and rear outside seat belts


D Keep the belts clean and dry.


If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive clean- ers—they may severely weaken the belts. (See “Cleaning the interior” in Part 5.)


D Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.


If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor. When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” in this chapter.) To free the belt again, fully retract the belt and then pull the belt out once more.


then


is


Adjust the seat as needed (front seats only) and sit up straight and well back in the seat. To fasten your belt, pull it out of the retractor and insert the tab into the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function normally, immediately contact your authorized Toyota CNG dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.


21


CAUTION


Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause serious injures in a collision.


Take up slack


Too high


Keep as low on hips as possible


the


lap and


the position of


Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.


Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. After adjustment make sure the anchor is locked in position.


22


CAUTION


—Rear center seat belt


Lengthen


lap


D High−positioned


belts


and loose−fitting belts both could cause serious injuries due to sliding un- der the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.


D For your safety, do not place the


shoulder belt under your arm.


To release the belt, press the buckle−re- lease button and allow the belt to re- tract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.


Sit up straight and well back in the seat. To fasten your belt, insert the tab into the buckle. You will hear a click when the tab locks into the buckle. If the belt is not long enough for you, hold the tab at a right angle to the belt and pull on the tab.


23


CAUTION


Too high


D After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function normally, immediately contact your authorized Toyota CNG dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.


24


Adjust to a snug fit


Keep as low on hips as possible


Remove excess length of the belt and adjust the belt position. To shorten the belt, pull the free end of the belt. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit.


CAUTION


High−positioned and loose−fitting lap belts could cause serious injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.


To release the belt, press the buckle−re- lease button.


D Remember that the extender pro- vided for you may not be safe when used on a different vehicle, or for another person or at a different seating position than the one origi- nally intended for.


—Seat belt extender If your seat belt cannot be fastened se- curely because it is not long enough, a personalized seat belt extender is avail- able from your authorized Toyota CNG dealer free of charge. Please contact your authorized Toyota CNG dealer so that he/she can order the proper required length for the extender. Bring to wear for proper measurement and selec- tion of length. Additional ordering informa- tion is available at your authorized Toyota CNG dealer.


the heaviest coat you expect


CAUTION


When using the seat belt extender, observe the following. Failure to fol- low these instructions could result in less effectiveness of the seat belt re- straint system in case of vehicle acci- dent, increasing the chance of per- sonal injury. D Never use the seat belt extender if you can fasten the seat belt without it.


To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the “PRESS” signs on the buckle−release buttons of the ex- tender and the seat belt are both facing outward as shown. You will hear a click when the tab locks into the buckle. When releasing the seat belt, press on the buckle−release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extend- er itself. When not and store in the vehicle for future use.


in use, remove the extender


25


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the seat belt extender is not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function normally, immediately contact your authorized Toyota CNG dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.


—Front seat belt pretensioners


The driver and front passenger’s seat belt pretensioners are designed to be activated in response to a severe fron- tal impact. When the airbag sensor detects the shock of a severe frontal impact, the front seat belt is quickly drawn back in by the re- tractor so that the belt snugly restrains the front seat occupants. The seat belt pretensioners are activated even with no passenger in the front seat.


26


This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the front seat belt pretensioners are operating proper- ly. This warning the airbag sensor assembly, front airbag sen- sors, seat belt pretensioner assemblies, warning interconnecting wiring and power sources. (For details, see “Service reminder indicators and warning buzzers” in Chapter 1−5.)


light system monitors


light,


When a seat belt pretensioner is acti- vated, an operating noise may be heard and a small amount of smoke−like gas may be released. This gas is harmless and does not indicate that a fire is occur- ring. Once the seat belt pretensioner has been activated, the seat belt retractor remains locked.


CAUTION


Do not modify, remove, strike or open the front seat belt pretensioner as- semblies, airbag sensor or surround- ing area or wiring. Doing any of these may cause sudden operation of the front seat belt pretensioners or disable the system, which could re- sult in serious injury. Failure to follow these can result in serious injuries.


instructions


The seat belt pretensioner system mainly consists of the following components and their locations are shown in the illustra- tion. 1. Front airbag sensors 2. SRS warning light 3. Seat belt pretensioner assemblies 4. Airbag sensor assembly The seat belt pretensioner is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.


NOTICE


consulting


Do not perform any of the following changes without your authorized Toyota CNG dealer. Such interfere with proper changes can operation belt pretensioners in some cases. z Installation of electronic items such as a mobile two−way radio, cassette tape player or compact disc player z Repairs on or near the front seat


seat


the


of


belt retractor assemblies


z Modification of the suspension sys-


tem


z Modification of the front end struc-


ture


z Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end


z Repairs made on or near the front fenders, front end structure or con- sole


27


D If either front seat belt does not retract or can not be pulled out due to a malfunction or activation of the preten- sioner.


D The front seat belt pretensioner assem- bly or surrounding area has been dam- aged.


D The front part of the vehicle (shaded in the illustration) was involved in an accident that did not cause the seat belt pretensioners to operate.


D The front seat belt pretensioner assem- bly is scratched, cracked, or otherwise damaged.


SRS driver and front passenger airbags


The SRS (Supplemental Restraint Sys- tem) airbags are designed to provide further protection for the driver and front passenger when added to the pri- mary protection provided by the seat belts. In response to a severe frontal impact, the SRS airbags work together with the seat belts to help prevent or reduce injury by inflating, in order to decrease the likeli- hood of the driver’s or front passenger’s head or chest directly hitting the steering wheel or dashboard. The passenger airbag is activated even with no passenger in the front seat. Be sure to wear your seat belt.


the


following conditions occurs,


This front seat belt pretensioner system has a service reminder indicator to inform the driver of operating problems. If either of this indicates a malfunction of the airbags or pretensioners. Contact your authorized Toyota CNG dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or remains on.


D The light comes on or flashes while


driving.


28


CAUTION


A driver or front passenger too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. Toyota strongly recommends that: D The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle.


D The front passenger sit as far back


as possible from the dashboard.


D All vehicle occupants be properly restrained using the available seat belts.


This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, inflators, warning light, interconnect- ing wiring and power sources. (For details, see indicators and warning buzzers” in Chapter 1−5.)


light system monitors


reminder


“Service


The SRS airbag system is designed to activate in response to a severe frontal impact within the shaded area between the arrows in the illustration. There may be the case that the SRS air- bag will not activate with such an impact in which the occupant wearing the seat belt correctly would not get serious injury. The SRS airbags will deploy if the severi- ty of the impact is above the designed threshold level, comparable to an approxi- mate 25 km/h (15 mph) collision when impacting straight into a fixed barrier that does not move or deform.


29


this


level,


If the severity of the impact is below the above threshold the SRS airbags may not deploy. However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g. a collision in which the nose of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It is possible with collision severity at the marginal level of airbag sensor detection and activation that only one of your ve- hicle’s two airbags will deploy. For the safety of all occupants, be sure to always wear seat belts.


Collision rear


from


the


Collision from the side


Hitting a curb, edge of pavement or hard material


Falling into or jumping over a deep hole


Vehicle rollover


Landing hard or vehicle falling


The SRS airbags are not designed to inflate if the vehicle is subjected to a side or rear impact, if it rolls over, or if it is involved in a low−speed frontal collision.


The SRS airbags may deploy if a seri- ous impact occurs to the underside of your vehicle. Some examples are shown in the illustration.


30


the windshield as


A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.


In a severe frontal impact, sensors detect deceleration and the system triggers the airbag inflators. Then a chemical reaction in the inflators momentarily fills the air- bags with non−toxic gas to help restrain the forward motion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non−toxic gas. This does not indicate a fire. This gas is nor- mally harmless, however, for those who have delicate skin, it may cause minor skin irritation. Be sure to wash off any residue as soon as possible to prevent minor skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swellings. Parts of the airbag module (steering wheel hub, dashboard) may be hot for several minutes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.


The SRS airbag system mainly consists of the following components and their loca- tions are shown in the illustration. 1. Front airbag sensors 2. SRS warning light 3. Airbag module


for passenger (airbag


and inflator)


4. Airbag sensor assembly 5. Airbag module for driver (airbag and


inflator)


The airbag sensor assembly consists of a safing sensor and airbag sensor.


31


D Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint system. Toyota strongly recommends infants and children be placed in the rear seat of re- strained. The rear seat is the safest for in- structions concerning the installa- tion of a child restraint system, see “Child restraint” in this chapter.


the vehicle and properly


infants and children. For


that all


D Never put a rear−facing child re- straint system on the front seat be- cause the force of the rapid infla- tion of the passenger airbag can cause death or serious injury to the child.


CAUTION


D The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and front passenger side seat belt sys- tems. The front seat occupants can be killed or seriously injured by an inflating airbag if they do not wear the available seat belts. During sud- den braking just before a collision, an unrestrained driver or front pas- senger can move forward into direct contact with or close proximity to the airbag which may then deploy during the collision. To obtain maxi- mum protection in an accident, the driver and all passengers in the ve- hicle must wear their seat belts. Wearing a seat belt during an acci- dent reduces the chances of death or serious injuries or being thrown out of the vehicle. For instructions and precautions concerning the seat belt system, see “Seat belts” in this chapter.


32


Move seat fully back


D A forward−facing child restraint sys- tem should be allowed to put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child.


D Do not sit on the edge of the seat or lean over the dashboard when the vehicle is in use. The airbags inflate with considerable speed and force; you may be killed or serious- ly injured. Sit up straight and well back in the seat, and always use your seat belt.


D For


instructions concerning


the installation of a child restraint sys- tem, see “Child restraint” in this chapter.


D Do not allow a child to stand up, or to kneel on the front passenger seat. The airbag inflates with con- siderable speed and force; the child may be killed or seriously injured. D Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” in this chapter.


33


D Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing any of these may cause sud- den SRS airbag inflation or disable the system, which could result in death or serious injury. instructions Failure to follow these can result in death or serious inju- ries.


D Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the airbag system. They might restrict inflation or cause death or serious injury as they are projected rear- ward by the force of deploying air- bags. Likewise, the driver and front passenger should not hold things in their arms or on their knees.


34


NOTICE


consulting


Do not perform any of the following changes without your authorized Toyota CNG dealer. Such changes can interfere with proper operation of the SRS airbag system in some cases. z Installation of electronic items such as a mobile two−way radio, cassette tape player or compact disc player z Modification of the suspension sys-


tem


z Modification of the front end struc-


ture


z Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end


z Repairs made on or near the front fenders, front end structure, con- sole, steering wheel or dashboard near the front passenger airbag


steering


column,


If either of


This SRS airbag system has a service reminder indicator to inform the driver of operating problems. the following conditions occurs, this indicates a malfunction of the airbags. Contact your authorized Toyota CNG dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or remains on.


D The light comes on while driving.


In the following cases, contact your autho- rized Toyota CNG dealer as soon as pos- sible: D The SRS airbags have been inflated. D The front part of the vehicle (shaded in the illustration) was involved in an accident that did not cause the SRS airbags to inflate.


D The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.


passenger


airbag


front


NOTICE


Do not disconnect the battery cables before contacting your authorized Toyota CNG dealer.


35


D A forward−facing child restraint sys- tem should be allowed to put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child.


D Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured.


child


the


by


D Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. D Never put a rear−facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear−facing child restraint system is put on the front seat.


D Unless it is unavoidable, do not put the


restraint system on


a child front seat.


Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAEJ1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” for details.


CAUTION


D For effective protection in automo- bile accidents and sudden stops, children must be properly re- strained using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a sub- stitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s inte- rior.


36


the manufacturer’s


—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with either the lap belt or the lap portion of the lap/ shoulder belt. You must carefully con- sult instructions which accompany your child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the restraint sys- tem. Install the child restraint system correctly following the instructions provided by its manufacturer of the system. General di- rections are also provided under the fol- lowing illustrations. The child restraint system should be installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.


CAUTION


D Never put a rear−facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear−facing child restraint system is put on the front seat.


D Unless it is unavoidable, do not put the


restraint system on


a child front seat.


D A forward−facing child restraint sys- tem should be allowed to put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child. D After


installing the child restraint system, make sure it is secured in place following the manufacturer’s instructions. If it is not restrained securely, it may cause death or se- rious the event of a sudden stop or accident.


the child


injury


to


in


When not using the child restraint system, keep it secured with the seat belt or place it in the trunk or somewhere other than the passenger compartment. This will pre- vent the event of a sudden stop or accident.


injuring passengers


from


in


it


37


—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.


(A) Infant seat


(C) Booster seat


38


(B) Convertible seat


—Installation with 2−point type seat belt


(A) INFANT SEAT INSTALLATION An infant seat is used in rear−facing position only.


CAUTION


Do not put a rear−facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passen- ger in case of sudden braking or a collision.


1. Run


the


lap belt


the center


infant seat


through or around the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the lap belt.


following


39


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function it cannot protect your normally, injury. Contact your child authorized Toyota CNG dealer im- mediately. Do not use the seat until the seat belt is fixed.


from


40


2. While pressing the infant seat


firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.


CAUTION


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


3. To remove the infant seat, press the


buckle−release button.


(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward− facing and rear−facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instructions about the applicable child’s age and size as well as directions for installing a child restraint system.


follow


CAUTION


Do not put a rear−facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passen- ger in case of sudden braking or a collision.


41


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function it cannot protect your normally, injury. Contact your child authorized Toyota CNG dealer im- mediately. Do not use the seat until the seat belt is fixed.


from


2. While pressing


the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the convertible seat securely.


1. Run


lap belt


the center


through or following around its by the instructions tab into manufacturer and the buckle taking care not to twist the lap belt.


the convertible seat provided insert the


42


—Installation with 3−point type seat belt


CAUTION


3. To remove the convertible seat, press


the buckle−release button.


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


(A) INFANT SEAT INSTALLATION An infant seat is used in rear−facing position only.


43


CAUTION


D Never put a rear−facing child re- straint system on the front seat be- cause the force of the rapid infla- tion of the passenger airbag can cause death or serious injury to the child.


D Do not put a rear−facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden brak- ing or a collision.


1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.


44


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function it cannot protect your normally, injury. Contact your child authorized Toyota CNG dealer im- mediately. Do not use the seat until the seat belt is fixed.


from


2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.


the


To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.


3. While pressing the infant seat


firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.


45


CAUTION


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


4. To remove the infant seat, press the buckle−release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward− facing and rear−facing position depend- ing on the child’s age and size. When installing, follow the manufacturer’s in- structions about the applicable child’s age and size as well as directions for installing a child restraint system.


46


Move seat fully back


CAUTION


D Never put a rear−facing child re- straint system on the front seat be- cause the force of the rapid infla- tion of the passenger airbag can cause death or serious injury to the child.


D A forward−facing child restraint sys- tem should be allowed to put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child.


D Do not put a rear−facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden brak- ing or a collision.


47


CAUTION


D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


D If the seat belt does not function it cannot protect your normally, injury. Contact your child authorized Toyota CNG dealer im- mediately. Do not use the seat until the seat belt is fixed.


from


2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.


To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.


1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.


provided insert the


by tab


48


3. While pressing


the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.


CAUTION


Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.


4. To remove the convertible seat, press the buckle−release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.


freely again and be ready


49


(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward−fac- ing position only.


Move seat fully back


CAUTION


A forward−facing child restraint sys- tem should be allowed to put on the front seat only when it is unavoid- able. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child.


50


1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.


insert


the


tab


Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.


CAUTION


D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.


to do so could reduce


D If the seat belt does not function it cannot protect your normally, injury. Contact your child authorized Toyota CNG dealer im- mediately. Do not use the seat until the seat belt is fixed.


from


lap


D High−positioned


belts


and loose−fitting belts both could cause serious injuries due to sliding un- der the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.


D For child’s safety, do not place the


shoulder belt under child’s arm.


D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.


D Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.


2. To remove the child restraint system, press the buckle−release button and al- low the belt to retract.


51


Tilt steering wheel


Outside rear view mirrors—


CAUTION


D Do not adjust the steering wheel


while the vehicle is moving.


D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.


tilt


lever,


release


To change the steering wheel angle, hold the steering wheel, pull up the lock the steering wheel to the desired angle and release the lever. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.


52


Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror. On some models, when you push the rear window defogger switch, the heater panels in the outside rear view mirrors will quick- ly clear the mirror surface.


—Power rear view mirror control


NOTICE


If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.


CAUTION


D Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries.


D Since the mirror surfaces can get hot, keep your hands off them when the defogger switch is on.


To adjust a mirror, use the switches. 1. Master switch—To select the mirror to


be adjusted Place the switch at “L” (left) or “R” (right). 2. Control


switch—To move


the mir- the desired


ror P ush direction.


the switch


in


Mirror can be adjusted when key is in the “ACC” or “ON” position.


53


Loading...
x