Download PDF Manual


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


SECTION 8


SPECIFICATIONS Dimensions and weight Engine Fuel Service specifications Tires Fuses


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


288
288
289
289
292
292


2002 MY 4RUNNER_U (OM35787U)


287


’02 4Runner_U (L/O 0108)


Dimensions and weight


P265/70R 16 tire


mm (in.)


Engine Model: 5VZ–FE Type:


6 cylinder V type 4 cycle, gasoline


Bore and stroke, mm (in.):


93.5 (cid:1) 82.0 (3.68 (cid:1) 3.23)


Displacement, cm3 (cu. in.):


3378 (206.1)


P225/75R 15 tire


Without wheel opening extension


With wheel opening extension


Overall length


4655 (183.3)


4655 (183.3)


4655 (183.3)


Overall width


Overall height


Wheelbase


Front tread


Rear tread


1690


(66.5) (67.5)* 2675 (105.3)


1715


1730


(68.1) (68.5)* 2675 (105.3)


1740


1800


(70.9) (68.5)* 2675 (105.3)


1740


1505


(59.3)


1505


(59.3)


1505


(59.3)


1495


(58.9)


1510


(59.5)


1510


(59.5)


Vehicle capacity weight (occupants + luggage) kg (lb.):


454 (1000)


* : Unladen vehicle


288


2002 MY 4RUNNER_U (OM35787U)


Fuel Fuel type:


Unleaded gasoline, Octane Rating 87
(Research Octane Number 91) or higher


Fuel tank capacity, L (gal., Imp. gal.):


70 (18.5, 15.4)


’02 4Runner_U (L/O 0108)


Oil grade:


API grade SJ “Energy–Conserving”, SL “Energy–Conserving” or ILSAC multi- grade engine oil is recommended.


Recommended oil viscosity (SAE):


5W-30 Preferred


Temperature range anticipated before next oil change


Service specifications ENGINE Valve clearance (engine cold), mm (in.):


Intake Exhaust


0.13—0.23 (0.006—0.009) 0.27—0.37 (0.011—0.014)


Spark plug type:


DENSO NGK


K16TR11
BKR5EKB–11


Spark plug gap, mm (in.):


1.1 (0.043)


Drive belt roughs drive belt BT–33–73F (used belt), Ibf:


tension measured with Bor- tension gauge No.


Generator belt


100(cid:2)20


Air conditioning compressor belt


100(cid:2)20


Power steering pump belt


100 +20
–15


ENGINE LUBRICATION Oil capacity (drain and refill), L (qt., Imp. qt.):


With filter Without filter


5.2 (5.5, 4.6) 4.9 (5.2, 4.3)


2002 MY 4RUNNER_U (OM35787U)


289


’02 4Runner_U (L/O 0108)


AUTOMATIC TRANSMISSION Fluid capacity (drain and refill), L (qt., Imp. qt.):


Two–wheel drive models


Up to 1.6 (1.7, 1.4)


Four–wheel drive models


Up to 2.0 (2.1, 1.8)


Fluid type:


Automatic DEXRON(cid:2)III (DEXRON(cid:2)II)


transmission


fluid D–II or


TRANSFER Oil capacity, L (qt., Imp. qt.):


1.2 (1.3, 1.1)


Oil type:


Gear oil API GL–4 or GL–5


Recommended oil viscosity:


SAE 75W–90


DIFFERENTIAL Oil capacity, L (qt., Imp. qt.):


Two–wheel drive models


2.75 (2.9, 2.4)


Four–wheel drive models


Front


1.15 (1.2, 1.0)


Rear


With center differential lock system


2.75 (2.9, 2.4)


Without center differential lock sys- tem


2.45 (2.6, 2.2)


Oil type:


Hypoid gear oil API GL–5
Recommended oil viscosity:


Front


SAE 75W–90


Rear


Above –18(cid:1)C (0(cid:1)F)


SAE 90


Below –18(cid:1)C (0(cid:1)F)


SAE 80W or 80W–90


COOLING SYSTEM Total capacity, L (qt., Imp. qt.):


With rear heater Without rear heater


9.0 (9.5, 7.9) 8.0 (8.5, 7.0)


Coolant type:


“TOYOTA Long Life Coolant” or equiva- lent With ethylene–glycol type coolant for a proper corrosion protection of aluminum components Do not use alcohol type antifreeze or plain water alone.


BATTERY Open voltage* at 20(cid:1)C (68(cid:1)F):


12.6—12.8 V 12.2—12.4 V 11.8—12.0 V


Fully charged Half charged Discharged


* : Voltage that is checked 20 minutes af- the key is removed with all the


ter lights turned off


Charging rates:


5 A max.


290


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


STEERING Wheel free play:


Less than 30 mm (1.2 in.)


Power steering fluid type:


Automatic transmission fluid DEXRON(cid:2)II or III


CHASSIS LUBRICATION Propeller shafts:


Spiders


Lithium base chassis grease, NLGI No.2


Slide yoke and double cardan joint


Molybdenum–disulfide chassis grease, NLGI No.2


lithium


base


BRAKES Minimum pedal clearance when depressed with the force of 490 N (50 kgf, 110 lbf) with the engine running, mm (in.):


40 (1.6)


Pedal free play, mm (in.):


1—6 (0.04—0.24)


Pad wear limit, mm (in.):


1.0 (0.04)


Lining wear limit, mm (in.):


1.0 (0.04)


Parking brake adjustment when pulled with the force of 196 N (20 kgf, 44 lbf):


7—9 clicks


Fluid type:


SAE J1703 or FMVSS No.116 DOT 3


2002 MY 4RUNNER_U (OM35787U)


291


’02 4Runner_U (L/O 0108)


Tires Tire size, pressure and wheel size:


Tire size


Tire pressure


kPa (kgf/cm2 or bar, psi)


Front


Rear


P265/70R16 111S


220 (2.2, 32)


220 (2.2, 32)


P225/75R15 102S


200 (2.0, 29)


200 (2.0, 29)


Wheel size


7J(cid:1)16* 1
7JJ(cid:1)16* 2
7J(cid:1)15* 1
7JJ(cid:1)15* 2


Fuses


* 1: Vehicles with steel wheels * 2: Vehicles with aluminum wheels NOTE: For a complete


tires or replacing wheels), see “Checking tire pressure” through “Aluminum wheel precautions” in Section 7–2.


tires (e.g. replacing


information on


Wheel nut torque, N⋅m (kgf⋅m, ft⋅lbf):


110 (11.5, 83)


292


2002 MY 4RUNNER_U (OM35787U)


Engine compartment (without daytime running light system)


Fuses (type A) 1. ALT–S 7.5 A: Charging system 2. PWR OUTLET 15 A: Power outlets 3. RR HTR 10 A: Rear air conditioning


system


4. MPX–B 15 A: Power back window, back door lock, back window wiper, open door warning (back door), power door lock control system, back window defogger, horns, theft deterrent system


’02 4Runner_U (L/O 0108)


17. HEAD (HI LH) 10 A: Left–hand head-


light (high beam)


18. HEAD


(LO RH) 10 A: Right–hand


headlight (low beam)


19. HEAD (LO LH) 10 A: Left–hand head-


light (low beam)


20. TOWING 25 A: Trailer lights (back–up lights, rear turn signal lights, stop/tail lights)


21. SEAT HTR 20 A: Seat heater 22. FOG 15 A: Front fog lights 23. ECU–IG 10 A: Cruise control system, anti–lock brake system, vehicle skid control system, SRS airbag system, electronically automatic transmission system, power antenna, power window, electric moon roof, pow- er back window, back window defogger, back window wiper


controlled


24. TURN 10 A: Turn signals lights, emer-


gency flashers


25. WIPER 25 A: Windshield wipers and washer, power door lock control sys- tem, back window defogger, horns, theft deterrent system


26. 4WD 20 A: A.D.D. control system, four–wheel drive control system, center differential lock system


293


Engine compartment (with daytime running light system)


Instrument panel


luggage


5. DOME 15 A: Interior lights, personal light, lights, clock, car audio system, gauges and meters, ignition switch light, vanity mir- ror light, daytime running light


compartment


6. OBD 7.5 A: On–board diagnosis sys-


tem


7. EFI 20 A: Multiport fuel injection sys- injection


tem/sequential multiport system


fuel


10. TAIL 10 A: Tail


lights,


license plate


lights, instrument panel lights


11. A.C 10 A: Air conditioning system 12. MIR HTR 10 A: Outside rear view mir-


ror heaters


13. DEFOG 15 A: Back window defogger 14. ETCS 15 A: Multiport


fuel


injection injec-


fuel


system/sequential multiport tion system


8. HEAD(RH) 10 A: Right–hand headlight,


gauges and meters


9. HEAD(LH) 10 A: Left–hand headlight


15. DRL 7.5 A: Daytime running light sys-


tem


16. HEAD (HI RH) 10 A: Right–hand head- light (high beam), gauges and meters


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Fuses (type B) 34. HEATER 50 A: Air conditioning system,


all components in “A.C” fuse


35. AM1 40 A: Starting system, all compo- “TURN”,


nents “ECU–IG”, “WIPER” and “4WD” fuses


“GAUGE”,


“ACC”,


in


36. J/B 50 A: All components in “POWER”, “ECU–B”


“STOP” and


“HORN,HAZ”, fuses


37. AM2 30 A: Starting system, multiport fuel injection system/sequential multi- port fuel injection system, all compo- nents in “STA” and “IGN” fuses


38. ABS2 40 A: Anti–lock brake system, active traction control system, vehicle skid control system


39. POWER 30 A: Power window, power back window, electric moon roof, power seat, back door lock


Fuses (type C) 40. ABS 60 A: Anti–lock brake system 41. ALT 120 A: Charging system, all com- in “AM1”, “HEATER”, “TAIL”, “DEFOG”, “MIR


ponents “RR HTR”, “ALT–S”, HTR” and “ACC” fuses


27. ACC 15 A: Car audio system, power antenna, clock, power rear view mirror control, cigarette lighter, seat belt pre- tensioners, electronically controlled au- tomatic transmission system, power outlets, theft deterrent system


28. GAUGE 10 A: Gauges and meters, back window defogger, daytime running light system, air conditioning system, cruise control system, center differen- tial lock system, electronically con- trolled automatic transmission, back–up lights


29. IGN 10 A: SRS airbag system, seat belt pretensioners, multiport fuel injec- tion system/sequential multiport fuel in- jection system, discharge warning light, vehicle skid control system


30. ECU–B 7.5 A: Gauges and meters, air


conditioning system


31. HORN,HAZ 15 A: Horns, emergency


flashers


32. STA 7.5 A: Starting system 33. STOP 10 A: Stop lights, high–mounted


stoplight


294


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


SECTION 9


REPORTING SAFETY DEFECTS FOR U.S. OWNERS AND UNIFORM TIRE QUALITY GRADING Reporting safety defects for U.S. owners Uniform tire quality grading


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


296
296


2002 MY 4RUNNER_U (OM35787U)


295


’02 4Runner_U (L/O 0108)


To contact NHTSA, you may ei- ther call the Auto Safety Hotline toll–free at 1–800–424–9393 (or 366–0123 in Washington, D.C. area) or write to: NHTSA, U.S. Department of Transportation, Washington, D.C. 20590. You can also obtain other information about motor vehicle safety from the Hot- line.


Reporting safety defects for U.S. owners If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately in- form the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll–free: 1–800–331–4331). If NHTSA receives similar com- plaints, it may open an investiga- tion, and if it finds that a safety defect exists in a group of ve- hicles, it may order a recall and remedy However, NHTSA cannot become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc.


campaign.


296


2002 MY 4RUNNER_U (OM35787U)


Uniform tire quality grading This information has been prepared in ac- cordance with regulations issued by the National Highway Traffic Safety Adminis- tration of the U.S. Department of Trans- portation. It provides the purchasers and/ or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades—All passenger car tires must conform to Federal Safety Requirements these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A


in addition


to


from


treadwear grade


Treadwear—The is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150
would wear one and a half (1–1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual condi- tions of their use, however, and may de- part significantly the norm due to variations in driving habits, service prac- tices and differences in road characteris- tics and climate. Traction AA, A, B, C—The traction grades, from highest to lowest, are AA, A, B, and C, and they represent the tire’s ability to stop on wet pavement as mea- sured under controlled conditions on spe- cified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this is based on braking (straight ahead) traction tests and does not include cornering (turning) traction.


tire


’02 4Runner_U (L/O 0108)


Temperature A, B, C—The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissi- pate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to de- generate and reduce tire life, and exces- sive temperature can lead to sudden tire failure. The grade C corresponds to a lev- el of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No.109. Grades B and A represent higher levels of perfor- mance on the laboratory test wheel than the minimum required by law. Warning: The temperature grades for this tire are established for a tire that is prop- erly inflated and not overloaded. Exces- sive speed, underinflation, or excessive loading, either separately or in combina- tion, can cause heat buildup and possible tire failure.


2002 MY 4RUNNER_U (OM35787U)


297


’02 4Runner_U (L/O 0108)


298


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


SECTION 1– 1


OPERATION OF INSTRUMENTS AND CONTROLS Overview of instruments and controls Instrument panel overview Instrument cluster overview Indicator symbols on the instrument panel


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Instrument panel overview


1. Side vents 2. Tilt steering lock release lever 3. Instrument cluster 4. Center vents 5. Garage door opener 6. Garage door opener box or auxiliary


box


7. Electric moon roof switch 8. Personal lights 9. Glove box 10. Power door lock switches 11. Power window switches 12. Automatic transmission selector lever 13. Parking brake lever 14. Ashtray 15. Cup holders 16. Front drive control lever 17. Lower vent 18. Hood lock release lever 19. Fuel filler door opener 20. Window lock switch 21. Power rear view mirror control switches


(with power windows)


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


1. Seat heater switch (for passenger) 2. Headlight and turn signal switch, and


front fog light switch


3. Wiper and washer switches 4. Back window and outside rear view


mirror defoggers switch


5. Driving pattern selector button 6. Clock 7. Emergency flasher switch 8. Power back window switch 9. Theft deterrent system/Engine


immobiliser system indicator light


10. Front passenger’s seat belt reminder


light


11. Air conditioning controls 12. Car audio 13. Ashtray 14. Power outlets 15. Cigarette lighter 16. “OUT/T” (outside temperature) button 17. Ignition switch 18. Cruise control switch 19. Center differential lock switch 20. Instrument panel light control knob 21. Power rear view mirror control switch


(without power windows)


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


22. Traction control off switch 23. Seat heater switch (for driver) or


Power back window lock switch


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Instrument cluster overview


1. Service reminder indicators and


indicator lights


2. Engine coolant temperature gauge 3. Tachometer


4. Speedometer 5. Odometer and two trip meters 6. Fuel gauge


7. Trip meter reset knob


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Indicator symbols on the instrument panel


Brake system warning light* 1


Driver’s seat belt reminder light* 1


Vehicle skid control system and traction control system (two–wheel drive models) or active traction control system (four–wheel drive models) warning light* 1


Front passenger’s seat belt reminder light* 1


Open door warning light* 1


Discharge warning light* 1


SRS warning light* 1


Low engine oil pressure warning light* 1


Unengaged “Park” warning light* 1


Malfunction indicator lamp* 1


Low fuel level warning light* 1


or


Anti–lock brake system warning light* 1


Automatic transmission fluid temperature warning light* 1


Low windshield washer fluid level warning light* 1


Turn signal indicator lights


Headlight high beam indicator light


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Overdrive–off indicator light


Automatic transmission indicator lights


Driving pattern (“PWR” mode) indicator light


Four–wheel drive and center differential lock indicator lights


Slip indicator light


Traction control system off indicator light* 1
(two–wheel drive models) Vehicle skid control system off indicator light* 1
(four–wheel drive models)


Cruise control indicator light* 2


* 1: For details, see “Service reminder


indicators and warning


buzzers” in Section 1–5.


* 2: If this light flashes, see “Cruise control” in Section 1–6.


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


SECTION 1– 2


OPERATION OF INSTRUMENTS AND CONTROLS Keys and Doors Keys Engine immobiliser system Side doors Power windows Power back window Back door Hood Theft deterrent system Fuel tank cap Electric moon roof


. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .


10
13
14
22
24
26
28
29
31
32


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Keys (without engine immobiliser system)


Keys (with engine immobiliser system)


Your vehicle is supplied with two kinds of keys. 1. Master key—This key works in every


lock.


2. Sub key—This key will not work in the


glove box.


To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant. Since the doors can be locked without a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle.


KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend you to write down the key number and keep it in safe place.


Your vehicle is supplied with the two kinds of keys. 1. Master key (black)—This key works in lock. Your Toyota dealer will every need it to make you a new key with built–in transponder chip.


2. Sub key


(gray)—This key does not


work in the glove box.


A transponder chip for engine immobiliser system has been filled in the head of the master and sub keys. These chips are needed to enable the system to function correctly, so be careful not to lose these keys. If you make your own duplicate key, you will not be able to cancel the system or start the engine.


10


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


To protect things locked in the glove box when you have your vehicle parked, leave the sub key with the attendant. Since the side doors can be locked with- out a key, you should always carry a spare master key in case you accidentally lock your keys inside the vehicle. For the wireless remote control key, see “Side doors” in this section.


information on use of


NOTICE


When using a key containing a trans- ponder chip, observe the following precautions: (cid:2) When starting the engine, do not use the key with a key ring resting on the key grip and do not press the key ring against the key grip. Otherwise the engine may not start, or may stop soon after it starts.


(cid:2) When starting the engine, do not use the key with other transponder keys around (including keys of oth- er vehicles) and do not press other key plates against the key grip. Otherwise the engine may not start, or may stop soon after it starts. If this happens, remove the key once and then insert it again after taking off other transponder keys (includ- ing keys of other vehicles) from the ring or while gripping or covering them with your hand to start the engine.


2002 MY 4RUNNER_U (OM35787U)


11


’02 4Runner_U (L/O 0108)


(cid:2) Do not cover the key grip with any material that cuts off electromagnet- ic waves.


(cid:2) Do not knock the key hard against


other objects.


(cid:2) Do not leave the key exposed to high temperatures for a long period, such as on the dashboard and hood under the direct sunlight.


(cid:2) Do not put the key in water or


wash it in an ultrasonic washer.


(cid:2) Do not use the key with electromag-


netic materials.


(cid:2) Do not bend the key grip.


12


2002 MY 4RUNNER_U (OM35787U)


KEY NUMBER PLATE Your key number is shown on the plate. Keep the plate in a safe place such as your wallet, not in the vehicle. If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. We recommend you to write down the key number and keep it in safe place.


’02 4Runner_U (L/O 0108)


Engine immobiliser system


Inserting the registered key in the ignition switch automatically cancels the system, which enables the engine to start. The indicator light will go off. For your Toyota dealer to make you a new key with built–in transponder chip, your dealer will need your key number and master key. However, there is a limit to the number of additional keys your Toyota dealer can make for you. If you make your own duplicate key, you will not be able to cancel the sys- tem or start the engine.


NOTICE


Do not modify, remove or disas- semble the engine immobiliser sys- tem. If any unauthorized changes or modifications are made, the proper operation of the system cannot be guaranteed.


immobiliser system


The engine is a theft prevention system. When you in- sert the key in the ignition switch, the transponder chip the key’s head transmits an electronic code to the ve- hicle. The engine will start, only when the electronic code in the chip corre- sponds to the registered ID code for the vehicle.


in


indicator


light will start


The system is automatically set when the key is removed from the ignition switch. The flashing to show the system is set. If any of the following indicator conditions occurs, contact your Toyota dealer. (cid:1) The


light stays on except when the theft deterrent system is set- ting or activating. (See “Theft deterrent system”.)


indicator


(cid:1) The indicator light does not start flash- ing when the key is removed from the ignition switch.


(cid:1) The indicator light flashes unsteady.


2002 MY 4RUNNER_U (OM35787U)


13


’02 4Runner_U (L/O 0108)


For vehicles sold in U.S.A.


For vehicles sold in Canada


Side doors


This device complies with RSS–210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.


interference,


including


FCC ID: MOZ RI–4BTY MADE IN JAPAN This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.


CAUTION


Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.


14


2002 MY 4RUNNER_U (OM35787U)


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock system— All lock and unlock simulta- neously with either front door. In the driv- er’s door lock, turning the key once will unlock the driver’s door and twice in suc- cession will unlock all the doors simulta- neously.


the doors


’02 4Runner_U (L/O 0108)


Driver’s side


Driver’s side


Front passenger’s side


Front passenger’s side


With power windows


Without power windows


2002 MY 4RUNNER_U (OM35787U)


15


LOCKING AND UNLOCKING WITH INSIDE LOCK BUTTON Move the lock button. To lock: Push the button downward. To unlock: Pull the button upward. Closing lock button pushed in will also lock the door. Be care- ful not to lock your keys in the vehicle. Vehicles with power door sys- tem—The front doors cannot be locked if you leave the key in the ignition switch.


the door with


lock


the


LOCKING AND UNLOCKING WITH POWER DOOR LOCK SWITCH Push the switch. To lock: Push the switch on the front side. To unlock: Push the switch on the rear side. All the doors lock or unlock simultaneous- ly. When the front side doors are locked from the outside or locked with the wireless remote control transmitter, the power door lock switch will not work until either front door is unlocked with the key, lock knob, or wireless remote control transmitter.


’02 4Runner_U (L/O 0108)


CAUTION


Before driving, be sure that the doors are closed and locked, especially when small children are in the ve- hicle. Along with the proper use of seat belts, locking the doors helps prevent the driver and passengers from being thrown out from the ve- hicle during an accident. It also helps prevent the doors from being opened unintentionally.


to


the


lock


lever


the “LOCK”


REAR DOOR CHILD–PROTECTORS Move position as shown on the label. This feature allows you to lock a rear door so it can be opened from the outside only, not from inside. We recommend us- ing this feature whenever small children are in the vehicle.


16


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


—Wireless remote control


Locking operation


Unlocking operation


The wireless remote control system is designed to lock or unlock all the side doors and back door from a distance within approximately 1 m (3 ft.) of the vehicle. LOCKING AND UNLOCKING THE SIDE DOORS AND BACK DOOR To lock and unlock all the side doors and back door, push the switches slow- ly and securely. To lock: Push the “LOCK” switch. All the side doors and back door are locked si- multaneously. At this time one beep will be heard, and tail lights flash once. Check to see that all the side doors and back door are securely locked. If any of the side doors or back door is not securely closed, locking cannot be performed by the “LOCK” switch and a beep will sound continuously for 10 sec- onds. However, if the key is in the igni- tion, a beep will not sound. To stop the buzzer, close all the doors securely or push the “UNLOCK” switch.


the


“UNLOCK” switch To unlock: Push once to unlock the driver’s door alone. Pushing the switch twice within 3 seconds unlocks all the side doors and back door simultaneously. Each time the “UNLOCK” switch is pushed, two beeps will be heard, and the parking lights and tail lights flash twice. You have 30 seconds to open a door after using the wireless remote unlock feature. If a door is not opened by then, all the side doors and back door will be automati- cally locked again. If the “LOCK” or “UNLOCK” switch is kept pressed in, the locking or unlocking opera- tion is not repeated. Release the button and then push again. The volume of beep sound can be changed. Contact your Toyota dealer for details if you require it.


2002 MY 4RUNNER_U (OM35787U)


17


’02 4Runner_U (L/O 0108)


REMOTE


CONTROL


WIRELESS TRANSMITTER The wireless remote control transmitter is an electronic component. Observe the fol- lowing instructions in order not to cause damage to the transmitter. (cid:1) Do not leave the transmitter on places the temperature becomes high


where such as on the dashboard.


(cid:1) Do not disassemble it. (cid:1) Avoid knocking


it hard against other


objects or dropping it.


(cid:1) Avoid putting it in water. You can use up to 4 wireless remote con- the same vehicle. trol Contact your Toyota dealer for detailed information.


transmitters


for


OPENING THE BACK WINDOW To open the back window, push the back window open switch of the trans- mitter for about 1 second. The window will fully open. At this time, you can hear a beep. If the ignition switch is in the “ON” posi- tion, the back window cannot be opened by the back window open switch. To open the back window with the master key, see “Power back window” in this sec- tion. The volume of beep sound can be changed. Contact your Toyota dealer for details if you require it.


flashes


to break


“PANIC” SWITCH Pushing the “PANIC” switch blows the horn intermittently and the headlights and tail lights. The “PANIC” switch is used to deter ve- hicle theft when you witness anyone at- tempting into or damage your vehicle. The alarm will last for one minute. To stop alarm midway, push “PANIC” or “UNLOCK” switch, or unlock any side door or back door with key. You can also stop the alarm by turning the ignition key from “LOCK” to the “ON” position. The “PANIC” mode does not work when the ignition key is in the “ON” position.


the


18


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


If the wireless remote control transmitter does not actuate the doors or operate from a normal distance: (cid:1) Check for closeness to a radio trans- mitter such as a radio station or an airport which can interfere with normal operation of the transmitter.


(cid:1) The battery may have been consumed. Check the battery in the transmitter. To replace see following “REPLACING THE BATTERY”.


the battery,


If you lose your wireless remote control transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an accident.


For vehicles sold in U.S.A.


This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.


interference


NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures:


to radio or


2002 MY 4RUNNER_U (OM35787U)


19


(cid:1) Reorient or relocate the receiving an-


tenna.


(cid:1) Increase the separation between the


equipment and receiver.


(cid:1) Connect the equipment into an outlet to


on a circuit different which the receiver is connected.


from


that


(cid:1) Consult the dealer or an experienced


radio / TV technician for help.


FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.


’02 4Runner_U (L/O 0108)


For vehicles sold in Canada


Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.


interference,


including


REPLACING THE BATTERY For CR2016 and a special screwdriver.


replacement, use a


lithium battery


CAUTION


Special care should be that small children do not swallow the re- moved battery or components.


taken


NOTICE


(cid:2) When replacing the transmitter bat- tery, be careful not to lose the com- ponents.


(cid:2) Replace only with the same or equivalent type recommended by the manufacturer.


(cid:2) Dispose of used batteries according


to the local laws.


Replace the battery by the following pro- cedures:


20


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


1. Using a coin or equivalent, open the


2. Remove the discharged transmitter bat-


3. Put new transmitter battery with posi-


transmitter case.


tery.


tive (+) side up.


Close the transmitter case securely.


NOTICE


(cid:2) Make sure the positive side and negative side of the transmitter bat- tery should be faced correctly.


(cid:2) Do not replace the battery with wet hands. Water may cause unexpected rust.


(cid:2) Do not touch or move any compo- nents inside of the transmitter, or it may interfere with proper opera- tion.


2002 MY 4RUNNER_U (OM35787U)


21


’02 4Runner_U (L/O 0108)


(cid:2) Be careful that dust or oils do not


adhere to the transmitter case.


(cid:2) Close the transmitter case securely.


Power windows


Window lock switch


that


replacing battery, check


After the transmitter operates properly. If the trans- mitter still does not operate properly, con- tact your Toyota dealer. If you lose your transmitter, contact your Toyota dealer as soon as possible to avoid the possibility of theft, or an acci- dent. (See “If you lose your wireless re- mote control transmitter” in Section 4.)


Driver’s door switches


22


2002 MY 4RUNNER_U (OM35787U)


Front passenger’s door switch


the


ignition switch


The windows can be operated with the switch on each side door. The power windows work when the ignition switch is in the “ON” position. Key off operation: front side If both doors are closed, they work for 43 se- conds even after is turned off. They stop working when either front side door is opened. OPERATING THE DRIVER’S AND FRONT PASSENGER’S WINDOWS Use the switches on the driver’s door and front passenger’s door. Normal operation: The window moves as long as you hold the switch. To open: Lightly push down the switch. To close: Lightly pull up the switch. If you push in the window lock switch on the driver’s door, front passengers’ window cannot be operated.


the


’02 4Runner_U (L/O 0108)


Automatic operation: Push the switch completely down or pull it completely up, and then release it. The window will fully open or close. To stop the window part- way, lightly move the switch in the oppo- site direction and then release it. If you push in the window lock switch on the driver’s door, front passengers’ window cannot be operated. Jam protection function: During automat- ic closing operation, the window stops and opens half way if something gets caught between the window and window frame. If the window receives a strong impact, this function may work even if nothing is caught.


the


CAUTION


(cid:1) Never try jamming any part of your jam protection


body to make the function work intentionally.


(cid:1) The


jam protection


function may not work if something gets caught just before fully closed.


the window


is


Window lock switch


Driver’s door switches


OPERATING THE REAR PASSENGERS’ WINDOWS Use the switch on each rear passen- ger’s door or the switches on the driv- er’s door that control each rear passen- ger’s windows. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch. If you push in the window lock switch on the driver’s door, rear passengers’ windows cannot be operated.


the


2002 MY 4RUNNER_U (OM35787U)


23


Driver’s door switches


Front passenger’s door switch


’02 4Runner_U (L/O 0108)


Power back window


CAUTION


To avoid serious personal injury, you must do the following. (cid:1) Always make sure the heads, hands and other parts of the bodies of all occupants are kept completely in- side the vehicle before you close the power windows. If someone’s neck, head or hands gets caught in a closing window, it could result in a serious injury. When anyone closes the power windows, make sure that he/she operates the win- dows safely.


(cid:1) When small children are in the ve- hicle, never let them use the power window switches without supervi- sion. Use the window lock switch to prevent from making unex- pected use of the switches.


them


(cid:1) Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power window switches and get in a window. Unat- tended children can be involved in serious accidents.


trapped


The back window can be operated with the inner switch on the center console or outer switch on the back door. OPERATING FROM INSIDE The ignition key must be in the “ON” posi- tion. The back window moves as long as you hold the inner switch.


To open: Push the switch on the “ side. To close: Push the switch on the “ side.




Rear passengers’ door switches


24


2002 MY 4RUNNER_U (OM35787U)


the wiper stops working until


You can also open the back window when the back window wiper is working. At that time, the window is closed again. If you push in the window lock switch on the driver’s door (with power windows) or on instrument panel (without power windows), the back window cannot be op- erated.


the


’02 4Runner_U (L/O 0108)


With power windows (driver’s door)


OPERATING FROM OUTSIDE After turning and holding the key for a few seconds, the back window will move as far as holding the key. To open: Turn the key counterclockwise. To close: Turn the key clockwise. You can also open the back window when the back window wiper is working. At the time, the window is closed again.


the wiper stops working until


Without power windows (instrument panel)


2002 MY 4RUNNER_U (OM35787U)


25


’02 4Runner_U (L/O 0108)


Back door


(cid:1) Keep the back window closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle.


Vehicles with wireless remote control sys- tem—To open the back window with the wireless remote control transmitter, see “—Wireless remote control” in this section.


CAUTION


To avoid serious personal injury, you must do the following. (cid:1) Always make sure the heads, hands and other parts of the bodies of all occupants are kept completely in- side the vehicle before you close the power back window. If some- one’s neck, head or hands gets caught it injury. could result When anyone closes the power back window, make sure that he/she operates the window safely.


in a closing window,


in a serious


(cid:1) When small children are in the ve- hicle, never let them use the power back window switch without super- vision. Use the window lock switch to prevent them from making unex- pected use of the switch.


(cid:1) Never leave small children alone in the vehicle, especially with the igni- tion key still inserted. They could use the power back window switch and get trapped in a window. Unat- tended children can be involved in serious accidents.


26


2002 MY 4RUNNER_U (OM35787U)


LOCKING AND UNLOCKING WITH KEY Insert the key into the keyhole and turn it. To lock: Turn the key clockwise. To unlock: Turn the key counterclockwise. To open the back door, pull the lever. The back door will be controlled by oper- ating the power door lock switch.


’02 4Runner_U (L/O 0108)


CAUTION


Driver’s side


Keep the back window and back door closed while driving. This not only keeps the luggage from being thrown out but also prevents exhaust gases from entering the vehicle.


NOTICE


To prevent damage to the back door dampers, do not apply any force, paint or let any other foreign matter on them.


Front passenger’s side


2002 MY 4RUNNER_U (OM35787U)


27


With power windows


When closing the back door, use the inside strap for easier reach to the back door. To close the back door, lower it and press down on it. After closing the back door, try pulling it up to make sure it is secure- ly closed. See in Section 2 for precautions in loading lug- gage.


“Luggage stowage precautions”


Driver’s side


Front passenger’s side


’02 4Runner_U (L/O 0108)


Hood


LOCKING AND UNLOCKING WITH POWER BACK DOOR LOCK SWITCH Push the switch. To lock: Push the switch on the front side. To unlock: Push the switch on the rear side. Operating the power door lock switch si- multaneously locks or unlocks the back door. (See “Side doors” in this section.) Vehicles with wireless remote control sys- tem—To lock or unlock the back door, see “—Wireless remote control” in this section.


To open the hood: 1. Pull the hood lock release lever. The


hood will spring up slightly.


CAUTION


Before driving, be sure that the hood is closed and securely locked. Other- wise, the hood may open unexpected- ly while driving and an accident may occur.


Without power windows


28


2002 MY 4RUNNER_U (OM35787U)


’02 4Runner_U (L/O 0108)


Theft deterrent system


2. In front of the vehicle, pull up the the


lever and


lift


auxiliary catch hood.


3. Hold the hood open by inserting the


support rod into the slot.


Before closing the hood, check to see that you have not forgotten any tools, rags, etc. and return its clip—this prevents rattles. Then lower the hood make sure If necessary, press down gently on the front edge to lock it.


the support rod


into place.


locks


to


it


To deter the vehicle theft, the system is designed to give an alarm if any of the side doors, back door or hood is forcibly unlocked or opened or the bat- tery terminal is disconnected and then reconnected when the vehicle is locked. The alarm blows the horn intermittently and flashes the headlights and tail lights.


CAUTION


After inserting the support rod into the slot, make sure the rod supports the hood security from falling down on to your head or body.


2002 MY 4RUNNER_U (OM35787U)


29


’02 4Runner_U (L/O 0108)


Reactivating the alarm Once set, the system automatically resets the alarm after the alarm stops. The alarm will activate again under the same circumstances in “Activating the system”. Stopping the alarm The alarm will be stopped by the following three ways: (cid:1) Turn the ignition key from the “LOCK”


described


to “ON” position.


(cid:1) Unlock any of the side doors or back door with the key or wireless remote control transmitter. These ways cancel same time.


the system at


the


The system will automatically be set after 30 seconds. When the system is set, the indicator light will start flashing again. 4. After making sure


light starts flashing, you may leave the ve- hicle.


indicator


the


Never leave anyone in the vehicle when you set the system, because unlocking from the inside will activate the system. WHEN THE SYSTEM IS SET Activating the system The system will give the alarm under the following conditions: (cid:1) If any of the side doors is unlocked or opened without the key or wireless re- mote control transmitter, or if the back door or hood is forcibly opened.


(cid:1) If the battery terminal is disconnected


and then reconnected.


The indicator light will come on when the system is activated. If the alarm has been activated and the key is not in the ignition switch, all the side doors and back door will re–lock au- tomatically. After one minute, the alarm will automati- cally stop and the indicator light will starts flashing again.


2002 MY 4RUNNER_U (OM35787U)


SETTING THE SYSTEM 1. Turn


the ignition key position and remove it.


to the “LOCK”


is


removed


The indicator light will start flashing when the key ignition switch. (See “Engine immobiliser system” for details.) 2. Have all passengers get out of


from


the


the


vehicle.


3. Close and lock all the side doors, back


door and hood.


The indicator light will come on when all the side doors, back door and hood are closed and locked.


30


TESTING THE SYSTEM 1. Open all the windows. 2. Set


the system as described above. The side doors and back door should be locked with the key or wireless re- mote control to wait until the indicator light goes off or starts flashing.


transmitter. Be sure


this operation


3. Unlock any side door from the inside. The system should activate the alarm. 4. Stopping the alarm as described above. 5. Repeat the other doors and hood. When testing on the hood, also check that the system is activated when the battery terminal is disconnected and then reconnected. the system does not work properly,


If have it checked by your Toyota dealer.


for


’02 4Runner_U (L/O 0108)


Fuel tank cap


1. To open the fuel filler door, pull the


lever. When refueling, turn off the engine.


2. To remove the fuel tank cap, turn the cap slowly counterclockwise, then pause slightly before removing it.


CAUTION


(cid:1) Do not smoke, cause sparks or al- flames when refueling.


low open The fumes are flammable.


(cid:1) When opening the cap, do not re- move the cap quickly. In hot weath- er, fuel under pressure could cause injury by spraying out of the filler neck is suddenly re- moved.


the cap


if


the cap clockwise


It is not unusual to hear a slight swoosh when the cap is opened. When installing, turn till you hear a click. If the cap is not tightened securely, the malfunction lamp comes on. Make sure the cap is tightened securely. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.


indicator


2002 MY 4RUNNER_U (OM35787U)


31


’02 4Runner_U (L/O 0108)


CAUTION

Loading...
x