2008 Subaru Tribeca Owners Manual

ger’s seat. . When the seat is occupied by an adult.

Seat, seatbelt and SRS airbags 1-53

. When a heavy article is placed on the seat.

When the front passenger’s seat is occu- pied by an adult, observe the following precautions. Failure to do so may lessen the load on the front passenger’s seat, deactivating the front passenger’s SRS frontal airbag despite the fact that the seat is occupied by an adult. . Do not allow the rear seat occupant to the front passenger’s seat cushion lift using his/her feet. . Do not place any article under the front passenger’s seat, or squeeze any article from behind and under the seat. This may lift the seat cushion. . Do not squeeze any article between the front passenger’s seat and side trim/ pillar, door or center console box. This may lift the seat cushion.

! If the passenger’s frontal airbag OFF

indicator illuminates and the ON indicator extinguishes even when the front passenger’s seat is occu- pied by an adult

This can be caused by the adult incor- rectly sitting in the front passenger’s seat. Turn the ignition switch to the “LOCK” position. Ask the front passenger to set the seatback to the upright position, sit up

– CONTINUED –

1-54 Seat, seatbelt and SRS airbags

If

straight in the center of the seat cushion, correctly fasten the seatbelt, position his/ her legs out forward, and adjust the seat to the rearmost position. Turn the ignition switch to the “ON” position. the OFF indicator remains illuminated while the ON indicator remains extinguished, take the following actions. . Turn the ignition switch to the “LOCK” position. . Ensure that there are no articles, books, shoes, or other objects trapped under the seat, at the rear of the seat, or on the side of the seat. . Next, turn the ignition switch to the “ON” position and wait 6 seconds to allow the system to complete self-checking. Following the system check, both indica- tors extinguish for 2 seconds. Now, the ON indicator should illuminate while the OFF indicator remains extinguished.

If the OFF indicator still illuminates while the ON indicator remains extinguished, ask the occupant to move to the rear seat and immediately contact your SUBARU dealer for an inspection. ! Effect vehicle modifications made for persons with disabilities may have on Subaru advanced frontal airbag system operation (U.S. only) Changing or moving any parts of the front

seats, seatbelts, front bumper, front side frame, instrument panel, combination me- ter, steering wheel, steering column, tire, suspension or floor panel can affect the operation of the Subaru advanced airbag system. If you have any questions, you may contact the following Subaru distribu- tors:

Subaru of America, Inc. Customer Dealer Services Department P.O. Box 6000
Cherry Hill, NJ 08034-6000
1-800-SUBARU3 (1-800-782-2783)

Servco Subaru Inc., dba Subaru Hawaii 2850 Pukoloa Street, Suite 202, Honolulu, HI 96819
808-839-2273

Trebol Motors P.O. Box 11204, San Juan, Puerto Rico 00910
787-793-2828

There are currently no Subaru distributors in any other U.S. territories. If you are in such an area, please contact the Subaru distributor or dealer from which you

bought your vehicle. ! Operation

1) Driver’s side 2) Passenger’s side

The SRS airbag can function only when the ignition switch is in the “ON” position.

The Subaru advanced frontal airbag sys- tem is designed to determine the activa- tion or deactivation condition of the front passenger’s SRS frontal airbag depend- ing on the total load on the front passen- ger’s seat monitored by the front passen- ger’s occupant detection system weight sensor. For this reason, only the driver’s SRS frontal airbag may deploy in the event of a collision, but this does not mean failure of the system.

If the front sub sensors located on both sides of the radiator panel and the impact sensors in the airbag control module detect a predetermined amount of force during a frontal collision, the control module sends signals to the airbag module(s) (only driver’s module or both driver’s and front passenger’s modules) instructing the module(s) to inflate the SRS frontal airbag(s). The driver’s and front passenger’s SRS frontal airbags use dual stage inflators. The two inflators of each airbag are triggered either sequen- tially or simultaneously, depending on the severity of impact, backward-forward ad- justment of the driver’s seat position and fastening/unfastening of the seatbelt in the case of the driver’s SRS frontal airbag and depending on the severity of impact and the total load on the seat in the case of the front passenger’s SRS frontal airbag. After

to the deflation of

deployment, the SRS airbag immediately starts to deflate so that the driver’s vision is not obstructed. The time required from detecting impact the is shorter SRS airbag after deployment than the blink of an eye. Both when only the driver’s SRS frontal airbag deploys and the driver’s and front passenger’s SRS frontal airbags deploy, the driver’s and front passenger’s seatbelt pretensioners operate at the same time.

Although it is highly unlikely that the SRS airbag would activate in a non-accident situation, should it occur, the SRS airbag will deflate quickly, not obscuring vision interfere with the driver’s and will not ability to maintain control of the vehicle.

When the SRS airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occurrences are a normal result of the deployment. This smoke does not indicate a fire in the vehicle.

CAUTION

Do not touch the SRS airbag system components around the steering wheel and dashboard with bare hands right after deployment. Doing so can cause burns because the

Seat, seatbelt and SRS airbags 1-55

components can be very hot as a result of deployment.

The driver’s SRS frontal airbag and front passenger’s SRS frontal airbag are de- signed to deploy in the event of an accident involving a moderate to severe frontal collision. It is basically not designed to deploy in lesser frontal impacts be- cause the necessary protection can be achieved by the seatbelt alone. Also, they are basically not designed to deploy in side or rear impacts or in rollover acci- dents because deployment of only the driver’s SRS frontal airbag or both driver’s and front passenger’s SRS frontal airbags would not help the occupant in those situations. The driver’s and front passen- ger’s SRS frontal airbags are designed to function on a one-time-only basis.

SRS airbag deployment depends on the level of force experienced in the passen- ger compartment during a collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle itself.

– CONTINUED –

1-56 Seat, seatbelt and SRS airbags

! Examples of accidents in which the

driver’s/driver’s and front passen- ger’s SRS frontal airbag(s) will most likely deploy.

! Examples of the types of accidents

in which it is possible that the driver’s/driver’s and front passen- ger’s SRS frontal airbag(s) will de- ploy.

both driver’s and front passenger’s SRS frontal airbags may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely impacted or knocked hard against an obstacle on the road such as a curb).

A head-on collision against a thick con- crete wall at a vehicle speed of 12 to 19
mph (20 to 30 km/h) or higher activates only the driver’s SRS frontal airbag or both driver’s and front passenger’s SRS frontal airbags. The airbag(s) will also be acti- vated when the vehicle is exposed to a frontal in fashion and magnitude to the collision described above.

impact similar

The only the driver’s SRS frontal airbag or

! Examples of the types of accidents in which deployment of the driver’s/ driver’s and front passenger’s SRS frontal airbag(s) is unlikely to occur.

of driver’s/driver’s and front passenger’s SRS frontal airbag(s). If the vehicle strikes an object, such as a telephone pole or sign pole, or if it slides under a truck’s load bed, or if it sustains an oblique offset the driver’s/driver’s and frontal front passenger’s SRS frontal airbag(s) may not deploy depending on the level of accident forces involved.

impact,

Seat, seatbelt and SRS airbags 1-57

! Examples of the types of accidents

in which the driver’s/driver’s and front passenger’s SRS frontal airbag(s) will basically not deploy.

There are many types of collisions which might not necessarily require deployment

The driver’s and front passenger’s SRS frontal airbags are designed basically not

– CONTINUED –

1-58 Seat, seatbelt and SRS airbags

to deploy if the vehicle is struck from the side or from behind, or if it rolls onto its side or roof, or if it is involved in a low- speed frontal collision.

First impact

1) 2) Second impact

In an accident where the vehicle is the driver’s impacted more than once, and/or front passenger’s SRS frontal airbag(s) will deploy only once on the first impact.

Example: In the case of a double collision, first with another vehicle, then against a concrete wall in immediate succession, once either or both of the driver’s and front passenger’s SRS frontal airbags is/are activated on the first impact, it/they will not be activated on the second impact.

& SRS side airbag and SRS

curtain airbag

The SRS side airbag is stored in the door side of each front seat seatback, which bears an “SRS AIRBAG” label. In a moderate to severe side impact the SRS side airbag on the collision, impacted side of the vehicle deploys between the occupant and the door panel and supplements the seatbelt by reducing the impact to the occupant’s chest and waist. The SRS side airbag operates only for front seat occupants. The SRS curtain airbag on each side of the cabin is stored in the roof side (between the front pillar and a point over the rear seat). An “SRS AIRBAG” mark is located at the top of each center pillar. In a moderate to severe side impact collision, the SRS curtain airbag on the impacted side of the vehicle deploys between the occupant and the side window and supplements the seatbelt by reducing the impact on the occupant’s head. In a rollover, SRS curtain airbags on both sides of the vehicle deploy between the occupant and the side window and sup- plement the seatbelt by reducing the impact to the occupant’s head. In a 7-seater model vehicle,

the SRS

curtain airbag does not operate for third- row seat occupants.

WARNING

The SRS side airbag and SRS curtain airbag are designed as only a supplement to the primary protec- tion provided by the seatbelt. They do not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper upright position.

WARNING

. Do not sit or lean unnecessarily

close to either front door. The SRS side airbag is stored in both front seat seatbacks next to the door, and it provides protection by deploying rapidly (faster than the blink of an eye) in the event of a side impact collision. However, the force of SRS side airbag deployment may cause injuries if your head or other parts of the body are too close to the SRS side airbag.

. Since your vehicle is equipped with SRS curtain airbags, do not sit or lean unnecessarily close to the front or rear door on either side. Also, do not put your head, arms and hands out of the win- dow. The SRS curtain airbag on each side of the cabin is stored in the roof side (between the front pillar and a point over the rear seat), and it provides protection by deploying rapidly (faster than the blink of an eye) in the event of a side impact or a rollover. How- ever, the force of its deployment may cause injuries if your head is too close to it.

WARNING

Do not rest your arm on either front door or its internal trim. It could be injured in the event of SRS side airbag deployment.

Seat, seatbelt and SRS airbags 1-59

WARNING

. Never allow a child to kneel on the front passenger’s seat facing the side window or to wrap his/ her arms around the front seat – CONTINUED –

1-60 Seat, seatbelt and SRS airbags

seatback. In the event of an accident, the force of the SRS side airbag deployment could injure the child seriously be- cause his/her head or arms or other parts of the body are too close to the SRS side airbag. Since your vehicle is also equipped with a front passen- ger’s SRS frontal airbag, children aged 12 and under should be placed in a rear seat anyway and should be properly restrained at all times.

. Never allow a child to kneel on any passenger’s seat facing the side window or put their head, arms and hands out of the win- dow. In the event of an accident, the force of the SRS curtain airbag deployment could injure the child seriously because his/ her head is close to the SRS curtain airbag.

A hands-free microphone or other accessory in such a loca- tion could be propelled through the cabin with great force by the curtain airbag, or it could prevent correct deployment of the curtain airbag. In either case, the result could be serious injuries.

WARNING

. Do not attach accessories to the door trim or near either SRS side airbags and do not place objects near the SRS side airbags. In the event of the SRS side airbag deployment, they could be pro- pelled dangerously toward the vehicle’s occupants and cause injuries.

. Do not attach a hands-free micro- phone or any other accessory to a front pillar, a center pillar, a rear pillar, the windshield, a side win- dow, an assist grip, or any other cabin surface that would be near a deploying SRS curtain airbag.

WARNING

Do not hang coat hangers or other hard or pointed objects on the coat hooks. If such items were hanging on the coat hooks during deploy- ment of the SRS curtain airbags, they could cause serious injuries by coming off the coat hooks and being thrown through the cabin or by

preventing deployment of the cur- tain airbags. Before hanging clothing on the coat hooks, make sure there are no sharp objects in the pockets. Hang cloth- ing directly on the coat hooks with- out using hangers.

front seat’s occupant.

! Operation

Seat, seatbelt and SRS airbags 1-61

left and right center pillars and rear wheel houses. In addition, the rollover sensor is inside the airbag control module. If a center pillar impact sensor senses an impact force above a predetermined level in a side collision, the control module causes both the SRS side airbag and curtain airbag on the impacted side to inflate regardless of whether the rear wheel house impact sensor on the same side senses an impact. If it is a rear wheel house impact sensor alone that senses a sufficiently strong impact force, the control module causes only the SRS curtain airbag on the impacted side to inflate. If the rollover sensor detects rollover of the vehicle, the control module inflates the curtain airbag. After deployment, the SRS side airbag immediately starts to deflate. The time required from detection of an impact to deflation of an SRS side airbag after deployment is shorter than the blink of an eye. The SRS curtain airbag remains inflated for a while following deployment then slowly deflates.

The SRS side airbag and SRS curtain airbag deploy even when no one occupies the seat on the side on which an impact is applied.

The SRS side airbag and SRS curtain airbag can function only when the ignition switch is in the “ON” position. The driver’s and front passenger’s SRS side airbags and SRS curtain airbags deploy independently of each other since each has its own impact sensor. There- fore, they may not both deploy in the same accident. Also, the SRS side airbag and SRS curtain airbag deploys independently of the driver’s and front passenger’s SRS frontal airbags in the steering wheel and instrument panel.

WARNING

Do not put any kind of cover or clothes or other objects over either front seatback and do not attach labels or stickers to the front seat surface on or near the SRS side airbag. They could prevent proper deployment of the SRS side airbag, reducing protection available to the

An impact sensor is located in each of the

When the SRS side airbag and SRS

– CONTINUED –

side airbag and SRS curtain airbag deployment would not help the occupant in those situations. Each SRS side airbag and SRS curtain airbag are designed to function on a one- time-only basis.

SRS side airbag and SRS curtain airbag deployment depend on the level of force experienced in the passenger compart- ment during a side impact collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle itself. Also, the SRS curtain airbag de- ploys depending on the vehicle’s position and inclination at the time of the rollover.

! Example of the type of accident in which the SRS side airbag will most likely deploy.

A severe side impact near the front seat activates the SRS side airbag.

1-62 Seat, seatbelt and SRS airbags

curtain airbag deploy, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occur- rences are a normal result of the deploy- ment. This smoke does not indicate a fire in the vehicle.

CAUTION

Do not touch the SRS side airbag system components around the front seat seatback with bare hands right after deployment. Doing so can cause burns because the compo- nents can be very hot as a result of deployment. After deployment, do not touch any part of the SRS curtain airbag system (from the front pillar to the part of the roof side over the rear seat). Doing so can cause burns because the components can be very hot as a result of deployment.

The SRS side airbag and SRS curtain airbag are designed to deploy in the event of an accident involving a moderate to severe side impact collision. Also, in the case of a rollover, the SRS curtain airbag deploys. They are basically not designed to deploy in a lesser side impact. Also, they are basically not designed to deploy in frontal or rear impacts because SRS

! Examples of the types of accidents in which the SRS curtain airbag will most

likely deploy.

Seat, seatbelt and SRS airbags 1-63

1) A severe side impact near the front seat or the rear seat activates the SRS curtain airbag. The vehicle rolls onto its side or the roof. If the angle of vehicle tip-up is marginal or if the skidding vehicle’s tires hit a curbstone laterally.

2) 3)

– CONTINUED –

1-64 Seat, seatbelt and SRS airbags

! Examples of the types of accidents in which it is possible that the SRS side

airbag and the SRS curtain airbag will deploy.

1) Hitting a curb, edge of pavement or hard

surface Falling into or jumping over a deep hole Landing hard or vehicle falling

2) 3)

It is possible that the SRS side and curtain airbags will deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustra- tion.

! Examples of the types of accidents in which the SRS side airbag is unlikely to

deploy.

Seat, seatbelt and SRS airbags 1-65

1)

2)

3)

4)

5)

The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment. The vehicle strikes a telephone pole or similar object. The vehicle is involved in a side-on impact from a motorcycle. The vehicle rolls onto its side or the roof.

There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of acci- dents like those illustrated, the SRS side airbag may not deploy depending on the level of accident forces involved.

– CONTINUED –

1-66 Seat, seatbelt and SRS airbags

! Examples of the types of accidents in which the SRS curtain airbag is unlikely

to deploy.

1)

2)

3)

The vehicle is involved in an oblique side-on impact. The vehicle is involved in a side-on impact in an area outside the vicinity of the passenger compartment. The vehicle is involved in a side-on impact from a motorcycle.

There are many types of collisions which might not necessarily require SRS curtain airbag deployment. In the event of acci- dents like those illustrated, the SRS curtain airbag may not deploy depending on the level of accident forces involved.

! Examples of the types of accidents

in which the SRS side airbag and SRS curtain airbag will basically not deploy.

2)

The vehicle is struck from behind.

The SRS side airbag and SRS curtain airbag are basically not designed to deploy if the vehicle is involved in a frontal collision or is struck from behind. Exam- ples of such accidents are illustrated. ! Example of the type of accident in

which the SRS curtain airbag will basically not deploy.

The SRS curtain airbags are not basically designed to deploy if the vehicle pitches end over end.

1)

The vehicle is involved in frontal collision with another vehicle (moving or station- ary).

Seat, seatbelt and SRS airbags 1-67

First impact

1) 2) Second impact A) SRS curtain airbag B) SRS side airbag

In an accident where the vehicle is struck from the side more than once, the SRS side airbag and SRS curtain airbag deploy only once on the first impact.

Example: In the case of a double side impact collision, first with one vehicle and immediately followed by another from the same direction, once the SRS side airbag and SRS curtain airbag are activated on the first impact, they will not be activated on the second.

– CONTINUED –

1-68 Seat, seatbelt and SRS airbags

& SRS airbag system monitors

A diagnostic system continually monitors the readiness of the SRS airbag system (including front seatbelt pretensioners) while the vehicle is being driven. The SRS airbag system warning light “AIR- BAG” will show normal system operation by lighting for approximately 6 seconds when the ignition switch is turned to the “ON” position.

The following components are monitored by the indicator: . Front sub sensor (Right-hand side) . Front sub sensor (Left-hand side) . Airbag control module (including im- pact and rollover sensors) . Frontal airbag module (Driver’s side) . Frontal airbag module (Front passen-

(Rear wheel

(Rear wheel

ger’s side) . Side airbag sensor (Center pillar right- hand side) . Side airbag sensor (Center pillar left- hand side) . Side airbag module (Driver’s side) . Side airbag module (Front passenger’s side) . Curtain airbag sensor house right-hand side) . Curtain airbag sensor house left-hand side) . Curtain airbag module (Right side) . Curtain airbag module (Left side) . Seatbelt pretensioner (Driver’s side) . Seatbelt pretensioner (Front passen- ger’s side) . Seatbelt buckle switch (Driver’s side) . Seatbelt buckle switch (Front passen- ger’s side) . Driver’s seat position sensor . Front passenger’s seatbelt sensor . Front passenger’s occupant detection system weight sensor . Front passenger’s occupant detection control module . Front passenger’s frontal airbag ON and OFF indicator . All related wiring

tension

WARNING

If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pretensioners and/or SRS airbag system. Immediately take your vehi- cle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g. SRS airbags may inflate in a very minor collision or not inflate in a severe collision), which may in- crease the risk of injury. . Flashing or flickering of the warn-

ing light

. No illumination of

the warning light when the ignition switch is first turned to the “ON” position the

. Continuous illumination of

warning light

. Illumination of the warning light

while driving

& SRS airbag system servicing

WARNING

. When discarding an airbag mod- ule or scrapping the entire vehi- cle damaged by a collision, con- sult your SUBARU dealer.

. The SRS airbag has no user- serviceable parts. Do not use electrical test equipment on any circuit related to the SRS airbag system. For required servicing of the SRS airbag, see your nearest SUBARU dealer. Tampering with or disconnecting the system’s wiring could result in accidental inflation of the SRS airbag or could make the system inopera- tive, which may result in serious injury. The wiring harnesses of the SRS airbag system are cov- ered with yellow insulation and system connectors are yellow for easy identification.

CAUTION

If you need service or repair in areas listed in the following, have an authorized SUBARU dealer perform the work. The SRS airbag control

module, impact sensors and airbag modules are stored in these areas. . Under the center console . Inside each front fender . Steering wheel and column and

nearby areas

. Top of the dashboard on front passenger’s side and nearby areas

. Each front seat and nearby area . Inside each center pillar . In each roof side (from the front pillar to a point over the rear seat) . Between the rear seat cushion and rear wheel house on each side

In the event that the SRS airbag is deployed, replacement of the system should be performed only by an author- ized SUBARU dealer. When the compo- nents of the SRS airbag system are replaced, use only genuine SUBARU parts. NOTE In the following cases, contact your SUBARU dealer as soon as possible. . The front part of the vehicle was involved in an accident in which only

Seat, seatbelt and SRS airbags 1-69

the driver’s SRS frontal airbag or both driver’s and front passenger’s SRS frontal airbags did not deploy. . The pad of the steering wheel, the cover over the front passenger’s SRS frontal airbag, or either roof side (from the front pillar to a point over the rear seat) is scratched, cracked, or other- wise damaged. . Either center pillar and rear wheel house or a nearby area of the vehicle was involved in an accident in which the SRS side airbag and SRS curtain airbag did not deploy. . The fabric or leather of either front seatback is cut, frayed, or otherwise damaged.

& Precautions against vehicle

modification

WARNING

. To avoid accidental activation of the system or rendering the sys- tem inoperative, which may re- sult in serious injury, no modifi- cations should be made to any components or wiring of the SRS airbag system. This includes following modifica- tions:

– CONTINUED –

1-70 Seat, seatbelt and SRS airbags

. Installation of custom steering

wheels

. Attachment of additional trim

materials to the dashboard . Installation of custom seats . Replacement of seat fabric or

leather

. Installation of additional fabric

or leather on the front seat

. Attachment of a hands-free microphone or any other ac- cessory to a front pillar, a center pillar, a rear pillar, the windshield, a side window, an assist grip, or any other cabin surface that would be near a deploying SRS curtain airbag. . Installation of additional elec- trical/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could interfere with prop- er operation of the SRS airbag system.

CAUTION

Do not perform any of the following modifications. Such modifications can interfere with proper operation of the SRS airbag system. . Attachment of any equipment (bush bar, winches, snow plow, skid plate, etc.) other than genu- ine SUBARU accessory parts.

. Modification of

the suspension

system or front end structure.

. Installation of a tire of different size and construction from the tires specified on the vehicle placard attached to the driver’s door pillar or specified for indivi- dual vehicle models in this Own- er’s Manual.

. Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body.

Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle.

Keys .................................................................. Key number plate............................................. Immobilizer ....................................................... Security ID plate............................................... Security indicator light ..................................... Key replacement .............................................. Door locks ........................................................ Locking and unlocking from the outside ........... Locking and unlocking from the inside ............. Battery drainage prevention function ................ Power door locking switches.......................... Key lock-in prevention function ........................ Remote keyless entry system ......................... Locking the doors ............................................ Unlocking the doors ......................................... Unlocking the rear gate .................................... Illuminated entry .............................................. Vehicle finder function...................................... Sounding a panic alarm.................................. Selecting audible signal operation .................. Replacing the battery ..................................... Replacing lost transmitters ..............................

2-2
2-2
2-3
2-3
2-4
2-4
2-4
2-4
2-5
2-6
2-6
2-7
2-7
2-8
2-9
2-9
2-9
2-9
2-10
2-10
2-10
2-11

Keys and doors

Alarm system ................................................. System operation............................................ Activating and deactivating the alarm

system .........................................................

If you have accidentally triggered the alarm

system ......................................................... Arming the system ......................................... Disarming the system ..................................... Valet mode ..................................................... Passive arming............................................... Tripped sensor identification ........................... Shock sensors (dealer option)......................... Child safety locks .......................................... Windows......................................................... Power windows .............................................. Rear gate ........................................................ Moonroof (if equipped).................................. Tilt function .................................................... Sliding function .............................................. Anti-entrapment function................................. Sun shade ......................................................

2-15
2-15

2-15

2-15
2-15
2-17
2-17
2-17
2-18
2-18
2-19
2-19
2-19
2-22
2-23
2-24
2-24
2-24
2-25

2-2 Keys and doors

Keys

box locked when you leave your vehicle and valet key at a parking facility.

CAUTION

Do not attach a large key holder or key case to either key. If it bangs against your knees while you are driving, it could turn the ignition switch from the “ON” position to the “Acc” or “LOCK” position, thereby stopping the engine.

& Key number plate

Write down the key number and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle.

For information on making replacement keys for vehicles with the immobilizer system, refer to the “Immobilizer” section in this chapter.

1) Master key 2) Submaster key 3) Valet key 4) Key number plate 5) Security ID plate

Three types of keys are provided for your vehicle. Master key, submaster key and valet key.

The master key and submaster key fit all locks on your vehicle. . Ignition switch . Driver’s door . Glove box

1) Key number plate 2) Security ID plate

The valet key fits only the ignition switch and door locks. You can keep the glove

The key number is stamped on the key number plate attached to the key set.

Immobilizer

The immobilizer system is designed to prevent an unauthorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregistered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds.

If

the transponder

Each immobilizer key contains a trans- in which the key’s ID code is ponder stored. When a key is inserted into the ignition switch and turned to the “ON” position, transmits the key’s ID code to the immobilizer system’s receiver. the transmitted ID code matches the ID code registered in the immobilizer system, the system allows the engine to be started. Since the ID code is transmitted and acted upon almost in- stantly, the immobilizer system does not impede normal starting of the engine. If the engine fails to start, pull out the key once before trying again. Refer to the “Ignition switch” section in chapter 3.

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This

inter- device may not cause harmful this device must ference, and (2) accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment. NOTE To protect your vehicle from theft, please pay close attention to the fol- lowing security precautions: . Never leave your vehicle unattended with its keys inside. . Before leaving your vehicle, close all windows and lock the doors and rear gate. . Do not leave spare keys or any record of your key number in the vehicle.

CAUTION

. Do not place the key under direct sunlight or anywhere it may become hot.

Keys and doors 2-3

. Do not get the key wet. If the key gets wet, wipe it dry with a cloth immediately.

& Security ID plate

1) Key number plate 2) Security ID plate

The security ID is stamped on the security ID plate attached to the key set. Write down the security ID and keep it in another safe place, not in the vehicle. This number is needed to make a replace- ment key if you lose your key or lock it inside the vehicle. This number is also needed for replace- ment or repair of the engine control unit, integrated unit, and combination meter.

– CONTINUED –

2-4 Keys and doors

& Security indicator light

The security indicator light deters potential thieves by indicating that the vehicle is equipped with an immobilizer system. It begins flashing approximately 60 seconds after the ignition switch is turned from the “ON” position to the “Acc” or “LOCK” position or immediately after the key is pulled out. If the security indicator light does not flash, the immobilizer system may be faulty. If this occurs, contact your SUBARU dealer as soon as possible.

In case an unauthorized key is used (e.g. an imitation key), the security indicator light comes on.

NOTE Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally.

& Key replacement Your key number plate and security ID plate will be required if you ever need a replacement key made. Any new key must be registered for use with your vehicle’s immobilizer system before it can be used. Up to four keys can be registered for use with one vehicle. For security, all the keys registered with your vehicle’s immobilizer system will have their ID codes erased and re- registered when a new key is made. Therefore, all of your vehicle’s keys must be presented when a new key is regis- tered. Any key that is not re-registered when a new key is made cannot be used after the other keys are re-registered. For information on replacement keys and on the registration of keys with your immo- bilizer system, contact your SUBARU dealer.

Door locks & Locking and unlocking from

the outside

To lock the driver’s door from the outside with the key, turn the key toward the front. To unlock the door, turn the key toward the rear.

Lift the outside door handle to open an unlocked door.

Locking without the key

To lock the door from the outside without the key, rotate the lock lever rearward and then close the door.

Keys and doors 2-5

It also helps prevent passengers from falling out if a door is acciden- tally opened, and intruders from unexpectedly opening doors and entering your vehicle.

To lock the door from the inside, rotate the lock lever rearward.

power door locking switch, push the “ ” sides of the switch and then close the door. In this case, all closed doors and the rear gate are locked at the same time.

Always make sure that all doors and the rear gate are locked before leaving your vehicle. NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside without the key.

& Locking and unlocking from

the inside

WARNING

Keep all doors locked when you drive, especially when small chil- dren are in your vehicle. Along with the proper use of seat- belts and child restraints, locking the doors reduces the chance of being thrown out of the vehicle in an accident.

Locking without the key

To lock the door from the outside using the

– CONTINUED –

2-6 Keys and doors

To unlock the door from the inside, rotate the lock lever forward.

The red mark on the lock lever appears when the door is unlocked. Pull the inside door handle to open an unlocked door. Always make sure that all doors and the rear gate are closed and locked before starting to drive.

& Battery drainage prevention

function

When a door or the rear gate is not completely closed and the map light, dome light, ignition switch light, and door open warning light remain illuminated as a result, the lights are automatically turned off by the battery drainage prevention

Power door locking switches

function after 10 minutes of illumination to prevent the battery from going dead. The operational/non-operational setting of this function can be changed by a SUBARU dealer. Contact the nearest SUBARU dealer if you would like to change the setting. NOTE . When leaving the vehicle, please make sure that all doors and the rear gate are completely closed. . The battery drainage prevention function does not operate while the key is in the ignition switch.

Driver’s switch 1) 2) Unlock

Lock

Front passenger’s switch

Lock

1) 2) Unlock

All doors and the rear gate can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors.

To lock all doors (including the rear gate), push the “ ” side of the switch. To unlock all doors (including the rear gate), push the “

” side of the switch.

When you close the doors after you set the door locks, the doors remain locked. NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside using the power door locking switches.

& Key lock-in prevention func-

tion

This function prevents the doors from being locked with the key still in the ignition switch. ! Behavior with key lock-in preven-

tion function operative

With either the driver’s or front passen- ger’s door open, the doors automatically remain unlocked even if the “ ” side of the door locking switch is pushed.

! Behavior with key lock-in preven-

tion function non-operative

Remote keyless entry system

Keys and doors 2-7

the spare key is used to lock the the

. If the lock lever is turned to the rear (“LOCK”) position with the driver’s door open and the driver’s door is then closed with the lock lever in that position, the driver’s door is locked. . If driver’s door vehicle, the door is locked. . It is possible to lock the all doors and the rear gate by holding the “ ” side of the door locking switch pushed for 3 seconds with the driver’s door open and then closing the driver’s door.

from the outside of

This function’s operative/non-operative setting can be changed by a SUBARU dealer. Contact a SUBARU dealer for details. NOTE When leaving the vehicle, make sure you are holding the key before locking the doors.

CAUTION

. Do not expose the transmitter to severe shocks, such as those experienced as a result of drop- ping or throwing.

. Do not take the transmitter apart except when replacing the bat- tery.

. Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.

This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful inter- this device must ference, and (2) accept any interference received, in- cluding interference that may cause undesired operation. Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

The transmitter for the remote keyless

– CONTINUED –

2-8 Keys and doors

entry system is located inside the key head.

The keyless entry system has the follow- ing functions. . Locking and unlocking the doors and rear gate without a key . Unlocking the rear gate without key . Sounding a panic alarm . Arming and disarming the alarm sys- to the next section “Alarm tem. Refer system” for detailed information.

The operable distance of the keyless entry system is approximately 30 feet (10
meters). However, this distance will vary depending on environmental conditions. The system’s operable distance will be shorter in areas near a facility or electronic equipment emitting strong radio waves such as a power plant, broadcast station, TV tower, or remote controller of home electronic appliances.

NOTE The keyless entry system does not operate when the ignition key is in- serted in the ignition switch or when any of the doors or the rear gate is not fully closed.

: Rear gate unlock button : Unlock/disarm button

: Lock/arm button

A: Panic button

& Locking the doors

Press the “ ” button to lock all doors and rear gate. An electronic chirp will sound once and the turn signal lights will flash once. If any of the doors or the rear gate is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors or the rear gate are not properly closed. When you close the door, it will automa- tically lock and then an electronic chirp will sound once and the turn signal lights will flash once.

& Unlocking the doors

& Unlocking the rear gate

Press the “ ” button to unlock the driver’s door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all doors and the rear gate, briefly press the “ ” button a second time within 5 seconds. NOTE If the interval between the first and second presses of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the sys- tem may not respond.

” button opens the rear

Pressing the “ gate. An electronic chirp will sound twice and the turn signal lights will flash twice.

& Illuminated entry Interior lights such as the map light, dome light and cargo area light will illuminate when the “ ” button is pressed. These lights stay illuminated for approximately 30 seconds if any of the doors or the rear gate is not opened. the “ ” button is pressed before 30
If seconds have elapsed, these lights will go out. To activate this function, set the following interior light switches to the indicated

Keys and doors 2-9

positions: Map light: OFF position Dome light: Middle position Cargo area light: DOOR position

A SUBARU dealer can change the illumi- nation period setting of the interior lights in accordance with your preference. Contact the nearest SUBARU dealer for details.

& Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30 feet (10 meters) of the vehicle, pressing the “ ” button three times in a 5-second period will cause your vehicle’s horn to sound once and its turn signal lights to flash three times. NOTE If the interval between presses is too short when you press the “ ” button three times, the system may not re- spond to the signals from the remote transmitter.

– CONTINUED –

2-10 Keys and doors

& Sounding a panic alarm

To activate the alarm, press the “PANIC” button once. The horn will sound and the turn signal lights will flash. To deactivate the panic alarm, press any button on the remote transmitter. Unless a button on the remote transmitter is pressed, the alarm will be deactivated after approximately 30 seconds.

& Selecting audible signal op-

eration

Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If desired, you may turn the audible signal off. Do the following to deactivate the audible

swallow them.

When the transmitter battery begins to get weak, range will begin to decrease. Replace the battery as soon as possible.

transmitter

To replace the battery:

in the driver’s seat and shut all

signal. You can also use the same steps to restore the function. 1. Sit doors and the rear gate. 2. Hold down the UNLOCK side of the power door locking switch. 3. While holding down the “UNLOCK” side of the power door locking switch, pull the key out and re-insert it into the ignition switch at least 6 times within 10 seconds after Step 2. 4. Open and close the driver’s door once within 10 seconds after step 3. 5. The turn signal lights flash 3 times to indicate completion of the setting.

You may have the above settings done by your SUBARU dealer. & Replacing the battery

CAUTION

1. Remove the screw on the key head.

. Do not let dust, oil or water get on or in the transmitter when repla- cing the battery. . Be careful not

to damage the printed circuit board in the trans- mitter when replacing the battery. . Be careful not to allow children to touch the battery and any re- moved parts; children could

Keys and doors 2-11

6. Replace with a new battery (Type CR1620 or equivalent) making sure to install the new battery with the negative (−) side facing up. 7. Put together the transmitter case by fitting the hooks on both sides of the case. 8. Put the transmitter case in the key head and then put together the key head. 9. Reinstall the screw on the key head.

After the battery is replaced, the trans- mitter must be synchronized with the keyless entry system’s control unit. Press either the “ ” or “ ” button six times to synchronize the unit. & Replacing lost transmitters to If you lose a transmitter or want purchase additional transmitters (up to four can be programmed), you should re- program all of your transmitters for secur- ity reasons. It is recommended that you have your dealer program all of your transmitters into your system. ! Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The system can learn up to four unique transmitter codes. The four transmitter codes may be the same or different.

– CONTINUED –

2. Open the key head using a flat-head screwdriver.

4. Open the transmitter case by releasing the hooks on both sides of the case. 5. Remove the old battery from the holder.

3. Remove the transmitter case from the key head.

1) Negative (−) side facing up

2-12 Keys and doors

Programming transmitter codes into system:

Bag containing transmitter

program the transmitter’s code (identifica- tion number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the transmitter. If there is no bag, open the transmitter case and make a note of the eight-digit number. Program the number into the system in accordance with the following procedure: 1. Firmly close the doors and the rear gate or trunk lid. 2. Open the driver’s door, sit on the driver’s seat, and close the door. 3. Perform the following steps within 45
seconds.

Transmitter circuit board

To register a new transmitter with the keyless entry system, it is necessary to

(1) Open and close the driver’s door once.

LOCK

1) 2) ON

(2) Insert the key into the ignition switch, then turn it from the “LOCK” position to the “ON” position 10 times within 15 seconds.

NOTE . When you complete step (2), an electronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely registered. . If you do not perform steps (1) and (2) within 45 seconds, an error will occur. Neither an electronic tone nor the buzzer will sound, and the interior lamp will not flash. In this event, per-

form the whole procedure again begin- ning with part 1. 4. Open and close the door once within 15 seconds. NOTE . When part 4 of the procedure is completed, an electronic tone will sound for 30 seconds. . If you do not perform the operations in part 4 within 15 seconds, an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with part 3 of the procedure.

times as the leftmost digit of the transmit- ter code. For example, push the locking switch eight times if the leftmost digit of the code is 8. NOTE . The electronic tone will stop sound- ing when you start entering the num- ber. . If you do not start entering the number using the lock knob before the electronic tone stops sounding, an error will occur. In this event, perform the registration steps again beginning with part 3 of the procedure. . If the interval between one push of the knob and the next exceeds 5
seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.

5. Before the electronic tone stops sounding, push the “ ” side of the power door locking switch the same number of

Keys and doors 2-13

6. When you have finished entering the number, push the “ ” side of the locking switch within 5 seconds. NOTE . An electronic tone will sound. . If you push the “ ” side of the locking switch when more than 5
seconds have passed, an error will occur. In this event, perform the proce- dure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 7. Perform parts 5 and 6 of the procedure for each of the transmitter code beginning with the sec- ond digit (counting from the left) and finishing with the eighth digit.

the remaining digits of

– CONTINUED –

2-14 Keys and doors

NOTE . When you finish entering the eighth digit, an electronic tone will sound for 30 seconds. . If the interval between one push of the switch and the next exceeds 5
seconds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3. 8. Before the electronic tone stops sounding, use the power door locking switch to reenter the transmitter code beginning with the leftmost digit. NOTE If you do not start entering the number using the lock knob before the electro- nic tone stops sounding, an error will occur. In this event, perform the proce- dure again beginning with part 3. 9. When you have finished entering the code a second time, an electronic tone will sound for 1 second and automatic door locking and unlocking operation will take place once to indicate completion of registration, provided the code entered the second time is identical to that entered the first time.

NOTE If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again beginning with part 5. If an error occurs five times, perform the procedure again starting with part 3. 10. If you wish to program another trans- mitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure begin- ning with part 4. When you have finished programming all of the necessary trans- mitter codes into the system, remove the key from the ignition switch. 11. Test every registered transmitter confirm correct operation.

to

! Deleting old transmitter codes The control unit of the keyless entry system has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmit- ter’s code remains in the memory. For security reasons, transmitter codes should be deleted from the memory. To delete old transmitter codes, program four transmitter codes into the system. If you have only one current transmitter,

lost

four times.

If you have two program it current transmitters, program each one twice. If you have three current transmit- ters, program two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmit- ters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access to your vehicle.

Alarm system

The alarm system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehicle.

The system can be armed and disarmed with the remote transmitter. The system does not operate when the key is inserted into the ignition switch. Your vehicle’s alarm system has been set for activation at the time of shipment from the factory. You can set the system for deactivation yourself or have it done by your SUBARU dealer.

& System operation The alarm system will give the following alarms when triggered: . The vehicle’s horn will sound and the turn signal lights will flash for 30 seconds. . If any door (or the rear gate) remains open after the 30-second period, the horn will continue to sound for a maximum of 3
minutes. If the door (or the rear gate) is closed while the horn is sounding, the horn will stop sounding with a delay of up to 30 seconds.

The alarm is triggered by:

. Opening a door or the rear gate . Physical impact to the vehicle, such as forced entry (only vehicles with shock sensors (dealer option))

& Activating and deactivating

the alarm system

to

in the driver’s seat and shut all

To change the setting of your vehicle’s alarm system for activation or deactiva- tion, do the following. 1. Disarm the alarm system (refer “Disarming the system” in this section). 2. Sit doors (and the rear gate). 3. Turn the ignition switch to the “ON” position. 4. Hold down the UNLOCK side of the driver’s power door locking switch, open the driver’s door within the following 1
second, and wait 10 seconds without releasing the switch. The setting will then be changed as follows:

If the system was previously activated: The odometer/trip meter screen displays “AL oF” and the horn sounds twice, indicating that the system is now deacti- vated.

If the system was previously deacti- vated: The odometer/trip meter screen displays

Keys and doors 2-15

“AL on” and the horn sounds once, indicating that the system is now acti- vated. NOTE You may have the above setting change done by your SUBARU dealer. & If you have accidentally trig-

gered the alarm system

! To stop the alarm Do any of the following operations: . Press any button on the remote trans- mitter. . Turn the ignition switch to the “ON” position.

& Arming the system ! To arm the system using remote

transmitter

1. Close all windows and the moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of vehicle. 4. Make sure that locked. 5. Close all doors (and the rear gate).

the engine hood is

the

– CONTINUED –

2-16 Keys and doors

: Press to Arm the system. : Press to Disarm the system.

once and the indicator lights will start flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator lights will then flash slowly (twice approxi- mately every 2 seconds), indicating that the system has been armed for surveil- lance.

If any of the doors, (or the rear gate) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors (or the rear gate) are not properly closed. When you close the door, the system will automatically arm and doors will automa- tically lock. ! To arm the system using power

door locking switches

1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of vehicle. 4. Make sure that locked. 5. Close the doors and the rear gate but leave only the driver’s door or the front passenger’s door open.

the engine hood is

the

6. Briefly press the “ ” button (for less than 2 seconds). All doors (and the rear gate) will lock, an electronic chirp will sound once, the turn signal lights will flash

6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the indicator lights will start flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator lights will then flash slowly (twice approxi- mately every 2 seconds), indicating that the system has been armed for surveil- lance.

NOTE . The system can be armed even if the engine hood, the windows and/or moonroofs are opened. Always make sure that they are fully closed before arming the system.

. The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer. . The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period. . If any of the following actions is done during the standby period, the system will not switch to the surveil- lance state.

. Doors are unlocked using the remote transmitter. . Any door (including the rear gate) is opened. . Ignition switch is turned to the “ON” position.

& Disarming the system Briefly press the “ ” button (for less than 2 seconds) on the remote transmitter. The driver’s door will unlock, an electronic chirp will sound twice, the turn signal flash twice and the indicator lights will light will go off.

To unlock all other doors and the rear gate, briefly press the “ ” button a second time within 5 seconds.

NOTE If the interval between the first and second presses of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the sys- tem may not respond. ! Emergency disarming If you cannot disarm the system using the transmitter is lost, broken or the transmitter battery is too weak), you can disarm the system without using the transmitter. The system can be disarmed if you turn the ignition switch from the “LOCK” to the “ON” position with a registered key.

the transmitter

(i.e.

& Valet mode When you choose the valet mode, the alarm system does not operate. In valet mode, the remote transmitter is used only for locking and unlocking the doors and rear gate and panic activation.

the valet mode, change the To enter setting of your vehicle’s alarm system for deactivation mode. (Refer to “Activating and deactivating the alarm system” in this section.) The security indicator light will continue to flash once every 3 seconds indicating that the system is in the valet mode.

Keys and doors 2-17

To exit valet mode, change the setting of your vehicle’s alarm system for activation mode. (Refer to “Activating and deactivat- ing the alarm system” in this section.)

& Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. ! To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. ! Arming the system

CAUTION

In passive mode, the system will automatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as in- dicated in step 4 below or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.

1. Turn the ignition switch to the “ON”

– CONTINUED –

2-18 Keys and doors

position.

LOCK

1) 2) ON

2. Turn the ignition switch from “ON” to “LOCK” position and remove the key from the ignition switch. 3. Open the doors and get out of vehicle.

the

4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will automatically arm after one minute.

In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door locking switch is used to lock the vehicle, arming will take place immediately regard- less of whether or not the passive mode has been selected. ! Disarming the system To disarm the system, briefly press the “

” button on the transmitter.

& Tripped sensor identification The security indicator light flashes when the alarm system has been triggered. Also, the number of flashes indicates the location of unauthorized intrusion or the severity of impact on the vehicle. . When the ignition switch is turned to the “ON” position, the indicator light will light for 1 second and then flash as follows:

When a door or rear gate was opened: 5 times When the ignition switch was turned to the “ON” position by using a key not registered with your immobilizer sys- tem: 3 times When a strong impact or multiple impacts were sensed: twice (only vehicles with shock sensors (dealer option)) When a light impact was sensed: once (only vehicles with shock sensors (dealer option))

& Shock sensors (dealer op-