2004 Subaru Legacy Owners Manual

on the radio in the weather band. Press the “WB” button when the radio is on to select the weather band. (cid:84) Manual tuning (TUNE) (cid:86) Manual tuning for AM and FM waveband Push the tuning button (7) marked “ ” to increase the tuning frequency and press the tuning button marked “ Each time the button is pressed, the frequency chang- es 10 KHz in the AM waveband and 0.2 MHz in the FM waveband.

” to decrease it.

Audio

(cid:86) Seek tuning If the tuning button (7) is pressed for longer than half of a second, the radio will begin to automatically search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situ- ation, perform manual tuning to select the desired sta- tion. (cid:86) Manual tuning for weather band When weather band mode is selected, press the tun- ” to change the WB chan- ing button (7) marked “ nel up and press the tuning button marked “ ” to change the WB channel down. Each time the button is pressed, the WB channel changes to the next chan- nel. (cid:84) Automatic tuning (SCAN) Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the fre- quency, after which scanning will continue until the en- tire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tun- – CONTINUED – 5-21

nance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is nec- essary to reset the preset buttons. (cid:121) If a mobile telephone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.

Audio

ing, stations are scanned in the direction of low fre- quencies to high frequencies only. Automatic tuning may not function properly if the sta- tion reception is weakened by distance from the sta- tion or proximity to tall buildings and hills. (cid:84) Selecting preset stations Presetting a station with a preset button (6) allows you to select that station in a single operation. Up to six AM, FM1, FM2 and WB stations each may be preset. (cid:84) How to preset stations 1. Press the “FM/AM” selection button to select AM, FM1 or FM2 reception.

Press the “WB” button (5) to select the weather band.

OR

2. Press the “SCAN” button (8) or tune the radio man- ually until the desired station frequency is displayed. 3. Press one of the preset buttons (6) for at least 1.5
seconds to store the frequency. The frequency of the station will flash once on the display at this time. If the button is pressed for less than 1.5 seconds, the pre- ceding selection will remain in memory. NOTE (cid:121) If the connection between the radio and battery is broken for any reason such as vehicle mainte-

5-22

(cid:132) Built-in CD changer operation

(9)

(10) (11)

(12)

(13) (14)

Audio

(9) Eject button (10) Disc slot (11) CD (CD player selection) button (12) Repeat button (13) Random button (14) LOAD button (15) Disc select buttons (16) Track selection buttons (17) SCAN button

(17)

(16)

(15)

UB5064CB

– CONTINUED – 5-23

Audio

NOTE Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. (cid:84) How to insert a CD(s) (cid:86) Inserting a CD 1. Press “LOAD” button (14). If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator associated with the idle position will blink. If no indicator blinks, it means that there is no idle po- sition in the magazine. 2. As soon as the “DISC” indicator begins to blink, the “IN” will appear on display for a period of 15 seconds. Insert a disc during the period. The disc will be then automatically drawn in, and the player will begin to play back the first number of the disc. (cid:121) To insert more discs in succession, repeat Steps 1
and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc in 15 seconds after you have pressed the “LOAD” button, the player will begin to play back the first number of the last disc you have inserted.

5-24

(cid:121) The disc indicator steadily lights up if a disc is al- ready inserted in the corresponding position of the magazine. (cid:121) While the player is in the loading mode, if you press the “FM/AM” selection button (4), the player will enter the standby mode. Press the “CD” button (11) to start playback. (cid:86) Inserting a disc in a desired position 1. Press the “LOAD” button. If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator associated with the idle position will blink. The positions in the magazine the indicator of which steadily lights up are already loaded with discs. 2. Press the “Disc select” button (15) at the position where you want to insert a disc. The associated “DISC” indicator will blink, and the “IN” will be dis- played. 3. If you insert a disc during the 15-second period while the “IN” is on display, the disc will be automati- cally drawn in, and the player will start playback of the disc, beginning with the first number. (cid:121) To insert more discs in succession, repeat Steps 1
and 2. (cid:121) While the player is in the loading mode, if you press the “FM/AM” selection button (4), the player will enter

standby mode. Press the “CD” button to start play- back. (cid:86) Loading all the magazine (Full disc loading

mode)

1. If you continue to press the “LOAD” button for more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode. 2. A “DISC” indicator will blink, and the “IN” will be on display for a period of 15 seconds. If a disc is success- fully loaded during this period, the “DISC” indicator will stop blinking and will steadily light. 3. When the loading of a disc is complete, the next “DISC” indicator will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15-second in- terval, the full disc loading mode will be canceled, and the player will start playback of the disc inserted first. (cid:84) How to play back a CD or make a pause (cid:86) When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first number.

Audio

(cid:86) When there are CDs loaded: Press a desired one of the “Disc select” buttons (15) the “DISC” indicator of which steadily lights up. The player will then start playback of the selected CD, be- ginning with the first number. (cid:84) To select a song from its beginning (cid:86) Forward direction Briefly press the “ ” button (16) to skip to the begin- ning of the next track. Each time the button is pressed, the indicated track number will increase. (cid:86) Backward direction Briefly press the “ ” button (16) to skip to the begin- ning of the current track. Each time the button is pressed, the indicated track number will decrease. (cid:84) Fast forwarding and fast reverse (cid:86) Fast forwarding Press the “ 0.5 second to fast forward the disc. Release the button to stop fast forwarding. (cid:86) Fast reverse Press the “ 0.5 second to fast reverse the disc. Release the button to stop fast reverse.

” button (16) continuously for more than

” button (16) continuously for more than

– CONTINUED – 5-25

Audio

(cid:84) Repeat playback Press the “RPT” button (12) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) Random playback Press the “RAND” button (13) while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal play- back mode is restored. (cid:84) Scan When the “SCAN” button (17) is pressed while the disc is being played back, you can hear the first 10 seconds of each track to seach for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc have been scanned, normal playback mode is restored.

5-26

(cid:84) How to unload CDs from the player (cid:86) Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc. 1. Press the “Disc select” button (15) of the disc whose “DISC” indicator is ON. 2. Press the “EJECT” button (9). Then the “DISC” in- dicator associated with the disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1
and 2. (cid:86) Ejecting all discs from the player (All disc ejec-

tion mode)

1. If you continue to press the “EJECT” button (9), the player will produce beep sound and will enter the all disc ejection mode. 2. Remove the disc that has been ejected. The other discs loaded will then be ejected one after another. If you do not remove the disc that has been ejected, the “All disc ejection mode” will be canceled. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.

(cid:132) OnStar® system operation (models

with OnStar® system)

When the OnStar system operates and a call is initiat- ed, the message “CALL” will be shown on the display, and the speakers will automatically switch over to the incoming voice signal. NOTE A call will not be suspended even if the ignition key is turned to the Off position. In such a case, however, the audio system will turn off when the call is ended.

Audio

McIntosh audio set (if equipped) The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions.

The power amplifier for this audio set is mount- ed under the front passenger’s seat. The ampli- fier will become hot if the audio continues to operate. Never touch the amplifier. Doing so could cause burns.

– CONTINUED – 5-27

(1) FM/AM selection button (2) Weather band button (3) Tuning/FF·FB dial (4) SCAN button (5) Preset buttons (6) Fader/Balance control button (7) Power switch, Volume control, Bass/Treble control and Fader/ Balance control dial

(8) Bass/Treble sound control but-

ton

Audio

(cid:132) Radio operation

(1) (2)

(3)

(8)

(7)

(6)

(5)

(4)

UB5063BB

5-28

(cid:84) Power switch and volume/bass/treble/fader/

balance control (ON/VOL)

The dial (1) is used for both power (ON/OFF) and vol- ume control. The radio is turned ON and OFF by push- ing the dial and the volume is controlled by turning the dial. This dial is used for bass/treble controls when the “BASS/TREB” button (8) is in the depressed position. It is also used for fader/balance controls when the “FAD/BAL” button (6) is in the depressed position.

Audio

– CONTINUED – 5-29

Audio

Display

Control mode

Bass control

Treble control

Fader control

Balance control

Turn counterclockwise

For less bass

For less treble

HS5014BA

Turn clockwise

For more bass

For more treble

To increase rear speaker volume and

decrease front speaker volume

To increase front speaker volume and

decrease rear speaker volume

To increase left speaker volume and

decrease right speaker volume

To increase right speaker volume and

decrease left speaker volume

Volume control

For less volume

For more volume

BASS TREB FAD

BAL

VOL

5-30

(cid:86) Tone control The volume control dial (7) normally function as vol- ume control. The dial become a control for Bass or Treble when you select the appropriate tone control mode. Choose desired level for each mode by turning the vol- ume control dial. The control function returns to vol- ume control mode after about 5 seconds. To change control modes: Each brief press of the “BASS/TREB” button (8) changes control modes in the following sequence starting from bass control mode. (When the radio is first turned on, the control mode is in the volume control.)

Bass (BASS)

Treble (TREB)

Volume (VOL)

(cid:86) Fader and balance control The volume control dial (7) normally function as vol- ume control. The dial become the controls for Fader or Balance when you select the appropriate fader and balance control mode. Choose desired setting for each mode by turning the volume control dial. The control function returns to vol- ume control mode after about 5 seconds.

Audio

To change control modes: Each brief press of the “FAD/BAL” button (6) changes control modes in the following sequence starting from fader control mode. (When the radio is turned on, the control mode is in the volume control.)

Fader (FAD)

Balance (BAL)

Volume (VOL)

(cid:86) Display illumination dimness cancellation

(BRIGHT)

” or “

The brightness of the radio display dims when the light switch is in the “ ” positions. If this makes the display difficult to read, press the dial (7) for more than two seconds to return the display to original brightness. Subsequently pressing the dial (7) again for more than two seconds or if you can safely do so, turning the light switch to the OFF position and back to the “ ” or “ (cid:84) FM/AM selection button Press the “FM/AM” selection button (1) to choose ei- ther FM or AM broadcasts. The display will show FM or AM accordingly. Use the tuning dial to select the station to which you

” position makes the radio display dim again.

– CONTINUED – 5-31

Audio

wish to listen. (cid:84) Weather band button (WB) Press the “WB” button (2) to choose weather band. The display will show WB. Use the tuning dial to select the station to which you wish to listen. (cid:84) Manual tuning Turn the tuning dial (3) outer tuner to increase or de- crease the reception frequency in individual steps.

FM band: 0.2 MHz steps AM band: 10 kHz steps Weather band: 1 step (1 channel)

(cid:84) Seek tuning (SEEK) If the Tuning dial (3) outer tuner is turned for longer than half of a second, the radio will begin to automati- cally search for receivable frequencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situ- ation, perform manual tuning to select the desired sta- tion. (cid:84) Scan tuning (SCAN) Press the “SCAN” button (4) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop

5-32

at the station for five seconds while displaying the fre- quency, after which scanning will continue until the en- tire band has been scanned. Turn the tuning dial (3) inner tuner again to cancel the SCAN mode and to stop on any displayed frequency. Scan tuning may not function properly if the station re- ception is weakened by distance from the station or proximity to tall buildings and hills. (cid:84) Preset tuning Press any one of the preset buttons (5) to select the corresponding, previously-registered radio station. The LED at the top of that button will turn on. (cid:86) Manual preset (cid:121) Use the tuning dial (3) to select the radio station which you wish to register. (cid:121) Choose the preset button (5) to which you wish to assign that station and press it continuously for a peri- od of more than 2 seconds. When the radio station has been successfully registered, the display will flash the corresponding radio frequency on and off once. NOTE (cid:121) Each preset button can be used to store both an FM station and an AM station. (cid:121) If the power supply is interrupted by disconnec- tion of the battery, memory presets will be cleared

and will be required to be re-input. (cid:121) If a mobile telephone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.

Audio

– CONTINUED – 5-33

Audio

(cid:132) Built-in CD changer operation

(9)

(10)

(9)

(11) (12)

(9) DISC IN indicator light (10) Disc slot (11) Eject button (12) LOAD button (13) Repeat button (14) FF·FB dial (15) Disc button (16) Disc select button

(14)

(15)

(13)

UB5063CB

(16)

5-34

NOTE (cid:121) Single CDs (i.e., 8-cm/3-inch CDs) are not sup- ported, and if inserted, they will be immediately ejected. (cid:121) Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. (cid:121) If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. (cid:121) After the last song finishes, the disc will auto- matically return to track 1 (the first song on the disc) and will automatically play back. (cid:84) How to insert a CD(s) (cid:86) Inserting a CD 1. Press “LOAD” button (12). If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator associated with the idle position will blink. If no indicator blinks, it means that there is no idle po- sition in the magazine. 2. As soon as the “DISC” indicator begins to blink, the “CD-IN” will appear on display for a period of 15 sec- onds. Insert a disc during the period. The disc will be then automatically drawn in, and the player will begin to play back the first number of the disc.

Audio

(cid:121) To insert more discs in succession, repeat Steps 1 and 2. The magazine will be loaded with discs in the ascending order of position number. If you do not insert any disc in 15 seconds after you have pressed the “LOAD” button (12), the player will begin to play back the first number of the last disc you have inserted. (cid:121) The disc indicator steadily lights up if a disc is al- ready inserted in the corresponding position of the magazine. (cid:121) While the player is in the loading mode, if you press “FM/AM” selection button (1), the player will enter the standby mode. Press the “Disc” button (15) to start playback.

(cid:86) Inserting a disc in a desired position 1. Press the “LOAD” button (12). If the magazine in the player has an idle position where you can insert a disc, the “DISC” indicator associated with the idle po- sition will blink. The positions in the magazine the indicator of which steadily lights up are already loaded with discs. 2. Press the “Disc select” button (16) at the position where you want to insert a disc. The associated “DISC” indicator will blink, and the “CD-IN” will be dis- played. 3. If you insert a disc during the 15-second period while the “IN” is on display, the disc will be automati- – CONTINUED – 5-35

(cid:84) How to play back a CD or make a pause (cid:86) When there is no CD inserted: Insert a CD by referring to “How to insert a CD(s)”. When a CD is loaded, the player will start playback of the CD, beginning with the first number. (cid:86) When there are CDs loaded: Press a desired one of the “Disc select” buttons (16) the “DISC” indicator of which steadily lights up. The player will then start playback of the selected CD, be- ginning with the first number.

Audio

cally drawn in, and the player will start playback of the disc, beginning with the first number. (cid:121) To insert more discs in succession, repeat Steps 1
and 2. (cid:121) While the player is in the loading mode, if you press FM/AM selection button, the player will enter standby mode. Press the “DISC” button to start playback. (cid:86) Loading all the magazine (Full disc loading

mode)

1. If you continue to press the “LOAD” button (12) for more than 1.5 seconds, the player will produce beep sound and will enter the full disc loading mode. 2. A “DISC” indicator will blink, and the “CD-IN” will be on display for a period of 15 seconds. If a disc is suc- cessfully loaded during this period, the “DISC” indica- tor will stop blinking and will steadily light. 3. When the loading of a disc is complete, the next “DISC” indicator will blink. Then repeat Step 2. 4. When the magazine is filled with discs by repeating Steps 2 and 3, the player will start playback of the discs, beginning with the one inserted first. If you fail to insert any disc during each 15-second in- terval, the full disc loading mode will be canceled, and the player will start playback of the disc inserted first.

5-36

(cid:84) Selecting a desired track (TRACK)

UB5065BA

: Skipping forward : Skipping backward : Fast forwarding : Fast reversing (cid:86) Skipping forward Turn the FF·FB dial (14) clockwise and release it im- mediately to skip to the beginning of the next track. Each time the knob is turned and released, the indicat- ed track number will increase. (cid:86) Skipping backward Turn the FF·FB dial (14) counterclockwise and release

Audio

it immediately to skip to the beginning of the current track. If you continue to turn and release the knob, the indicated track number will decrease. (cid:86) Fast forwarding Turn the FF·FB dial (14) clockwise and hold it contin- uously for more than 0.5 second to fast forward the disc. Release the knob to stop fast forwarding. (cid:86) Fast reversing Turn the FF·FB dial (14) counterclockwise and hold it continuously for more than 0.5 second to fast reverse the disc. Release the knob to stop fast reverse. (cid:84) Repeat playback Press the “RPT” button (13) while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored. (cid:84) How to unload CDs from the player (cid:86) Ejecting a CD from the player Of the discs loaded, you can select and remove only one disc.

– CONTINUED – 5-37

incoming voice signal. NOTE A call will not be suspended even if the ignition key is turned to the Off position. In such a case, however, the audio system will turn off when the call is ended.

Audio

1. Press the “Disc select” button (16) of the disc whose “DISC” indicator is ON. 2. Press the “EJECT” button (11). Then the “DISC” in- dicator associated with the disc you have selected will blink, and the disc will be ejected. To remove more discs in succession, repeat Steps 1
and 2. (cid:86) Ejecting all discs from the player (All disc ejec-

tion mode)

1. If you continue to press the “EJECT” button (11), the player will produce beep sound and will enter the all disc ejection mode. 2. Remove the disc that has been ejected. The other discs loaded will then be ejected one after another. If you do not remove the disc that has been ejected, the “All disc ejection mode” will be canceled. NOTE Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out.

(cid:132) OnStar® system operation (models

with OnStar® system)

When the OnStar system operates and a call is initiat- ed, the message “CALL” will be shown on the display, and the speakers will automatically switch over to the

5-38

In-dash 6 CD auto changer (if equipped)

(1)

(2)

Audio

(1) Disc slot (2) Disc indicators (disc No.1 to 6) (3) Disc select buttons (disc No.1 to

6)

(4) Eject button

(4)

(3)

HS5016BB

– CONTINUED – 5-39

Audio

mark.

identified by

(cid:121) Do not attempt to insert two or more discs into the slot at a time. Doing so can cause me- chanical damage to the CD changer. (cid:121) Use only music CDs (cid:121) Do not use CDs listed below which could cause damage to the CD player. (cid:121) 3-inch (8 cm) compact disc. (cid:121) Any disc with a peel-off or seal on it. (cid:121) Any disc with scratches and/or dust. (cid:121) Bent disc. (cid:121) Cleaning disc. (cid:121) CD accessory. (E.g., 3-inch (8 cm) disc adapter)

(cid:121) Do not insert or remove any disc when the automatic transmission selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).

(cid:84) To insert a disc 1. Press one of the “Disc select” buttons (3) (num- bered from 1 to 6) for which the disc indicator light (2)

5-40

is “OFF”. The Disc indicator lights are located directly above the corresponding “Disc select” buttons. 2. The indicator will begin blinking. The blinking will last for 15 seconds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the “Disc slot” (1) door will close. Repeat step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat step 1 and 2 choos- ing a different disc select button. (cid:84) To insert six discs at a time 1. Press and hold the “Disc select” button number 1
until all disc indicators begin blinking (about 1.5 sec- onds). 2. The indicators will blink for 15 seconds. During this period, insert desired six discs. 3. When all discs are loaded, the first disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.) (cid:84) To remove a disc 1. Press the desired one of the “Disc select” buttons (3) (numbered from 1 to 6) for which the disc indicator light is on.

2. Press the “Eject button” (4). The selected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat step 1 and 2
choosing a different “Disc select” button. (To remove discs when the ignition switch is in the “Lock” position, press the “Eject” button, and the first disc will be ejected. Press the “Eject” button again, and the next disc will be ejected and so on. At this time, the “Disc select” buttons are disabled.) (cid:84) To remove all discs at one time 1. Press and hold the “Eject” button (4) until all “Disc” indicators begin blinking (about 1.5 seconds), and the first disc will be ejected. 2. When the disc is removed, the next one will be ejected, and so on. (cid:84) To replace a playing disc with another Simply press the desired one of “Disc select” buttons (3) (numbered from 1 to 6) or press the “DISC UP” or “DISC DOWN” button on the radio unit to select the desired disc, and the disc will begin to play. (cid:84) Disc indicators Lit: when the corresponding storage tray is occupied by a disc. Blinking: Disc player is either in loading, eject or changing mode.

Audio

OFF: No disc is loaded or the ignition switch is in the “LOCK” position. (cid:84) Function control Refer to CD player control operating instructions de- scribed in the “Type A and B audio set (if equipped)” section.

– CONTINUED – 5-41

(cid:121) To remove a disc from the case, press the center of the case and hold both edges of the disc. If the disc surface is touched directly, contamination could cause poor tone quality. Do not touch the disc surface. (cid:121) Use a clean disc whenever possible. If there are de- posits, wipe the disc surface from the center outward with a dry, soft cloth. Be sure not to use a hard cloth, thinner, benzene, alcohol, etc. (cid:121) Do not use any disc that is scratched, deformed, or cracked. Also, do not use any disc that has a non-stan- dard shape (for example, a heart shape). Malfunctions or problems might result. (cid:121) A disc is vulnerable to heat. Never keep it either in places exposed to direct sunlight, near heaters or in vehicles parked in the sun or hot days.

Audio

Precautions to observe when han- dling a compact disc (CD) Use only compact discs (CDs) that have the mark shown below. CD-RWs cannot be used. Also, some CD-Rs cannot be played.

HS5017AA

(cid:121) In cold and/or rainy weather, dew can form inside the CD player, preventing normal operation. If this happens, eject the CD and wait for the player to dry out. (cid:121) Skipping may occur when the CD player is subject- ed to severe vibration (for example, when the vehicle is driven on a rough surface).

5-42

Audio

– CONTINUED – 5-43

HS5018BA

Interior light .................................................. Dome light ......................................................... Cargo area light (if equipped) .......................... Map light (if equipped) ................................. Sun visors ..................................................... Vanity mirror (if equipped) ............................... Storage compartment .................................. Glove box ........................................................... Center console .................................................. Coin compartment ............................................ Overhead console (if equipped) ...................... Cup holder .................................................... Front cup holder ............................................... Rear passenger’s cup holder (if equipped) .... Cigarette lighter socket (if equipped) ......... Use with a cigarette lighter .............................. Using as an accessory power outlet ............... Ashtray .......................................................... Front ashtray ..................................................... Rear ashtray (if equipped) ................................ OnStar® system (if equipped) ..................... OnStar services button .................................... OnStar emergency button ................................ OnStar communication button (White DOT) .. System status light ........................................... Volume control .................................................. OnStar subscription plans* .............................. OnStar services ................................................. OnStar personal calling .................................... OnStar virtual advisor ......................................

6-2
6-2
6-2
6-3
6-4
6-5
6-5
6-6
6-6
6-7
6-7
6-8
6-8
6-9
6-10
6-10
6-11
6-12
6-12
6-13
6-13
6-14
6-14
6-14
6-14
6-15
6-15
6-15
6-17
6-17

Interior equipment

In the luggage compartment (if equipped) .....

OnStar system limitations ...............................

Coat hook .......................................................... Shopping bag hook ..........................................

6-18
Accessory power outlet ............................... 6-19
6-19
Convenience hook ........................................ 6-20
6-20
6-20
Floor mat (if equipped) ................................. 6-21
Luggage cover (if equipped) ........................ 6-22
6-23
6-23
Convenient tie-down hooks (if equipped) .. 6-24
Subfloor storage (if equipped) ..................... 6-25

Using the cover ................................................. To remove the cover .........................................

6-1

Interior equipment

Interior equipment

Interior light (cid:132) Dome light

ON

DOOR

OFF

HS6025BB

The dome light switch has three positions: ON: The light stays on continuously. DOOR (middle position): The light comes on when any of the doors (or the rear gate on the wagon) is opened. The light remains on for several seconds and gradually goes out after all doors (and the rear gate on the wagon) are closed. The light also can be turned on by use of the keyless entry transmitter. See the “Remote keyless entry sys- tem (if equipped)” in chapter 2 for detailed information.

6-2

OFF: The light stays off. When leaving your vehicle, make sure the light goes out to avoid battery discharge.

(cid:132) Cargo area light (if equipped)

ON

OFF

DOOR

UB0377

The cargo area light switch has three positions: ON: The light stays on continuously. OFF: The light stays off. DOOR: The light comes on only when the rear gate is opened. When leaving your vehicle, make sure the light is turned off to avoid battery discharge.

Map light (if equipped)

Interior equipment

UG6021CB

Vehicle with moonroof (Sedan) 1) Switches 2) Map lights

Vehicle with dual moonroofs (Wagon) 1) Switches 2) Map lights

UB2006CC

– CONTINUED – 6-3

Interior equipment

Sun visors

UB6006BC

Vehicle without moonroof 1) Switches 2) Map lights To turn on the map light, push the switch. To turn it off, push the switch again. When leaving the vehicle, make sure the light is turned off to avoid battery discharge.

To block out glare, swing down the visors. To use the sun visor at a side window, swing it down and move it sideways.

UB7001BA

6-4

(cid:132) Vanity mirror (if equipped)

Storage compartment

Interior equipment

(cid:121) Always keep the storage compartment closed while driving to reduce the risk of injury in the event of sudden stops or an accident. (cid:121) Do not store spray cans, containers with flammable or corrosive liquids or any other dangerous items in the storage compartment.

UB6017AA

To use the vanity mirror, swing down the sunvisor and open the vanity mirror cover. (cid:84) Vanity mirror with light (if equipped) The light beside the vanity mirror comes on when the ignition switch is either in the “ACC” or “ON” position and the mirror cover is opened.

– CONTINUED – 6-5

Interior equipment

(cid:132) Glove box

(cid:132) Center console

HS6030BB

1) Lock 2) Unlock To open the glove box, pull the handle. To close it, push the lid firmly upward. To lock the glove box, insert the key and turn it clock- wise.

UB6022BA

To open the lid, pull up the lock release. If the console lid is fully opened when a large cup is put in the rear passenger’s cup holder, the lid may hit the cup and beverage may be spilled.

6-6

(cid:132) Coin compartment

(cid:132) Overhead console (if equipped)

Interior equipment

To open the coin compartment, pull the upper edge of the lid.

To open the console, push on the lid lightly and it will automatically open.

HS6055BA

UB0269

When your vehicle is parked in the sun or a warm day, the inside of the overhead console heats up. Avoid storing plastic or other heat- vulnerable or flammable articles such as a lighter in the overhead console.

– CONTINUED – 6-7

Interior equipment

Cup holder

(cid:132) Front cup holder

(cid:121) Do not pick up a cup from the cup holder or put a cup in the holder while you are driving, as this may distract you and lead to an accident. (cid:121) Take care to avoid spills. Beverages, if hot, might burn you or your passengers. Spilled beverages may also damage upholstery, car- pets or audio equipment.

A dual cup holder is built in the center console, beside the parking brake lever.

UB6056BA

6-8

(cid:132) Rear passenger’s cup holder (if

equipped)

Interior equipment

UB7009CA

The rear passenger’s cup holder is located on the low- er side of the back of the center console. To use the cup holder, open the lid by pulling its upper edge.

UB6024BA

– CONTINUED – 6-9

Interior equipment

Cigarette lighter socket (if equipped)

(cid:121) The electrical power socket located on the lower part of the instrument panel is originally designed to use a SUBARU genuine cigarette lighter plug. Do not use non-genuine cigarette lighter plugs in the socket. Doing so may cause a short-circuit and overheating, resulting in a fire. (cid:121) If the socket is ever used for a plug-in acces- sory such as a mobile phone, they may damage the portion of the socket’s internal mechanism that causes a cigarette lighter plug to “pop out” after its lighter element is heated. Therefore, do not place a cigarette lighter plug in a socket that has been used, even once, to power a plug- in accessory. Doing so may cause the plug to stick and overheat, creating a potential fire haz- ard. (cid:121) Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the socket. That could cause a short circuit.

6-10

UB6011BA

The electrical power socket located on the lower part of the instrument panel can be used as cigarette light- er socket. A cigarette lighter plug is an optional acces- sory. It is available from your SUBARU dealer. The cigarette lighter socket may also be used as a power source for an in-car use electrical appliance.

(cid:132) Use with a cigarette lighter

To avoid being burned, never grasp the lighter by the end with the heating element. Doing so could result in injury and could also damage

the heating element.

Do not hold the lighter pushed in, because it will overheat.

UB6011DA

The cigarette lighter operates only when the ignition switch is in the “ON” and “ACC” positions. To use the cigarette lighter, push in the knob and wait a few moments. It will automatically spring up when ready for use.

Interior equipment

(cid:132) Using as an accessory power outlet Electrical power (12V DC) from the battery is on tap at the socket when the ignition switch is either in the “ACC” or “ON” position. If you use the socket as an accessory power outlet, take the following precautions. When the socket is not in use, always put the cap on the socket to prevent any foreign object from entering it.

(cid:121) Use only in-car use electrical appliances which are designed for 12V DC and which con- sume less than 120W. Overloading the socket can cause a short circuit. Do not use double adapters or more than one electrical appliance. (cid:121) If the plug on your electric appliance is either too loose or too tight for the socket, this can re- sult in a poor contact or cause the plug to get stuck. Only use plugs that fit properly. (cid:121) Use of an electric appliance in the socket for a long period of time while the engine is not running can cause battery discharge. (cid:121) Before driving your vehicle, make sure that the plug and the cord on your electrical appli- ance will not interfere with your shifting gears – CONTINUED – 6-11

Interior equipment

and operating the accelerator and brake pedals. If they do, do not use the electrical appliance while driving.

Ashtray

If the socket has been used for electrical appliances, damage may have been done to the internal mecha- nism that cause a cigarette lighter to “pop-out” after its element has been heated. For that reason, a cigarette lighter, even if it is a genuine part, should not be used in the socket. If you want to use the socket for a ciga- rette lighter again, or to protect your purchaser before you sell your car, have your SUBARU dealer replace the socket with a new one.

Do not use ashtrays as waste receptacles or leave a lighted cigarette in an ashtray. This could cause a fire.

Fully close the ashtray after using it to help reduce re- sidual smoke.

(cid:132) Front ashtray

6-12

UB6011CA

To open the ashtray, pull the lid out.

(cid:132) Rear ashtray (if equipped)

Interior equipment

OnStar® system (if equipped)

UB7009BA

The rear ashtray is located on the upper side of the back of the center console. To open the ashtray, pull the upper edge of the lid. To remove the ashtray for cleaning, open it and pull it out while pushing the inner plate down.

UB6027BB

1) Emergency button 2) OnStar service button 3) Communication button 4) System status light OnStar is a vehicle communications system that offers a variety of services. OnStar provides a one-touch hands-free communication link between you and the OnStar Center, and allows you to make and receive personal calls as well. To receive OnStar services, a service subscription agreement is required and an ad- ditional fee may be required. Services are available 24
hours a day, 7 days a week. For more information, call – CONTINUED – 6-13

Interior equipment

1-888-ONSTAR7 (888-667-8277).

(cid:132) OnStar services button Press this button, and you will be connected to an On- Star Advisor. You will hear a chime, followed by the words “Connecting to OnStar”. The connection pro- cess will normally take about 15 seconds. Your sys- tem is equipped with backup connection retry capabil- ities. If you do not immediately connect to OnStar, DO NOT DISCONNECT. A series of retry attempts will be made automatically. If you wish to cancel your call to the OnStar center, simply press the OnStar Communi- cation button.

(cid:132) OnStar emergency button In an emergency, press this button to connect with an OnStar Advisor. Your call will be given the highest pri- ority, and you will hear a chime followed by the words “Connecting to OnStar Emergency.” The Advisor will attempt to locate your vehicle, find out what kind of as- sistance you require, and contact a nearby emergency services provider who can dispatch ambulance, fire, police or other emergency services. Please use this button only for true emergencies. If you press this but- ton by mistake, please stay on the line and tell the ad- visor that there is no emergency.

6-14

(cid:132) OnStar communication button

(White DOT)

Press this button at the end of a call. You’ll hear the words “OnStar Request Ended.” Also, press this but- ton to answer a call from the OnStar Center, or cancel a call if one of the other buttons is accidentally pressed. This button is also used to access OnStar Personal Calling and Virtual Advisor services, if those services have been activated.

(cid:132) System status light (cid:121) Solid green – Indicates the OnStar system in the vehicle is powered ON and ready to make or receive calls. (cid:121) Blinking green – The light blinks green to indicate a call is being connected or in progress. If you notice this light blinking while you are not on a call, press the OnStar Communication (white dot) button. (cid:121) Red – This signals that your OnStar system may not be functioning properly. Press the OnStar button to at- tempt to contact an OnStar advisor. If the connection is made, the advisor will assist you in making sure your OnStar system is operating properly. If you cannot contact the OnStar Center, please take your vehicle to the nearest SUBARU dealership for diagnosis and service.

(cid:132) Volume control You can control the volume of the OnStar System us- ing the volume control knob on the radio. (cid:132) OnStar subscription plans*1
(cid:84) The OnStar safe & sound plan Choose this plan for excellent protection, 24/7, 365
days a year. It includes valuable services such as Au- tomatic Notification of Air Bag Deployment, Remote Door Unlock*2 and Online Concierge services, to name just a few! (cid:84) The OnStar directions & connections plan This plan features all of the Safe & Sound services, plus Route Support, RideAssist and Information and Convenience services. (cid:84) The OnStar luxury & leisure plan This plan features all of the Directions & Connections features, plus fee-free OnStar MED-NET and the lux- ury of Personal Concierge services. *1: One of these plans is normally included for a specific du- ration with each vehicle at time of purchase. Check with your dealership or with your OnStar advisor to determine which plan is included with your vehicle. Services within plans are subject to change. Please check our website at www.on-

Interior equipment

star.com for services included in each plan. *2: Remote door unlock capabilities vary by vehicle

(cid:132) OnStar services The following services are available within OnStar ser- vice plans. Your vehicle comes with a specific one- year service plan that allows use of some or all of the following services. (cid:84) Automatic notification of air bag deployment Should your air bag deploy, a priority signal will be sent to the OnStar Center with your vehicle’s location (as long as cellular service and the vehicle’s electrical system are operable). An advisor will attempt to con- tact you to assess the nature of your emergency, and then notify the necessary emergency services provid- er. (cid:84) Emergency services Should you require emergency assistance, press the OnStar Emergency button and we will contact a near- by emergency services provider with your exact loca- tion and your request for help. (cid:84) Roadside assistance*3
There’s nothing worse than being stranded on the road with car trouble. No matter what the problem is – CONTINUED – 6-15

Interior equipment

(flat tire, out of gas, or engine trouble), just call OnStar. We will contact your vehicle manufacturer’s roadside service provider for the help you need to get you quick- ly back on the road. *3: There will be no charge for Roadside Assistance as long as the basic limited warranty on your vehicle has not expired. (cid:84) Stolen vehicle location OnStar doesn’t just protect you, it protects your vehi- cle, too. If your vehicle is ever stolen, just contact On- Star. We will put you in touch with the authorities and aid them in locating your vehicle. Ask your insurance carrier about possible premium discounts. (cid:84) AccidentAssist AccidentAssist provides step-by-step guidance about what to do in case of an accident. Working with leading insurance companies we have developed a “best practices” list to assist you through most accident sit- uations. OnStar AccidentAssist can make the process of completing a police report and/or insurance claim less stressful. (cid:84) Remote door unlock/vehicle alert If you’ve locked your keys in your vehicle, just call On- Star at 1-888-466-7827 (888-4ONSTAR) and an Advi- sor will send a signal to attempt to unlock your door. If you’re having trouble locating your vehicle, OnStar

6-16

can flash your lights and sound your horn for you. This feature is disabled 48 hours after the vehicle is parked in order to maintain battery charge. (cid:84) OnStar MED-NET*4
OnStar MED-NET securely stores your personal med- ical information (e.g., physician’s name, emergency contacts, medications, chronic conditions) and in an emergency, can quickly send it to a medical facility. This important information can help assist with diagno- sis and treatment. *4: Requires activation and additional fee for Safe & Sound and Directions & Connections subscribers. To enroll or for more OnStar Med-Net information, call 1-800-320-3991. (cid:84) Route support With OnStar Route Support, an Advisor can help you find your way, no matter how far off course you are. You can get exact street directions, or guidance to nearby gas stations, restaurants, hotels or ATMs. (cid:84) RideAssist If you need a lift, anytime of the day or night, just call OnStar. We’ll contact a transportation provider and send them right to you. (cid:84) Information and convenience services Our Advisors have access to over six million service

listings including hotels, restaurants, gas stations, dealerships, hospitals, ATMs and airports – more than 250 service categories in all. Our Advisors can even assist you with hotel and restaurant reservations. (cid:84) OnStar concierge Safe & Sound, Directions & Connections and Luxury and Leisure plan subscribers can access self-serve Online Concierge services for event tickets, dining reservations, gift recommendations and more at www.myonstar.com. Luxury & Leisure subscribers have access to Personal Concierge services. A Concierge Advisor can help you with virtually any type of request via email, live chat, phone (1-888-4ONSTAR) or the blue button in your vehicle. Just ask!

(cid:132) OnStar personal calling As an OnStar subscriber, you have access to OnStar Personal Calling (if available in your area). OnStar Personal Calling provides you with a nationwide wire- less phone service that is completely integrated in your vehicle. OnStar Personal Calling operates with the touch of a button and a few simple voice com- mands. All it takes to get started is a package of OPC minutes.

Interior equipment

With OnStar Personal Calling, you can enjoy the sim- plicity of a one-touch wireless connection. Whether you are placing or receiving a call, once you press the white dot button, you don’t have to take your hands off the wheel or your eyes off the road. The ease of the hands-free wireless communication service allows you to enjoy an even greater level of safety, security and convenience while driving.

(cid:132) OnStar virtual advisor As an OnStar Personal Calling subscriber, you can make your driving time more enjoyable and productive with the OnStar Virtual Advisor. With OnStar Virtual Advisor you can now listen to your favorite financial in- formation, news, entertainment and information top- ics, such as stock quotes , weather reports and sports scores. You can receive your email, listen to it being read and reply, without taking your hands off the wheel or eyes off the road. With the press of the white DOT button and a few simple voice commands, you can browse the pre-selected topics from your profile which you established on the MyOnStar website, or you can skip to the subjects that interest you. To find out more about Virtual Advisor or to set-up your Virtual Advisor personal profile, visit www.myon- star.com.

– CONTINUED – 6-17

Interior equipment

(cid:132) OnStar system limitations Complete limitations can be found on the Subscriber Services Agreement at www.onstar.com. An OnStar Service Subscription Agreement is re- quired in order to receive OnStar services, including OnStar Personal Calling and OnStar Virtual Advisor. OnStar services require vehicle electrical system and wireless service to be available and operating for fea- tures to function properly. OnStar uses existing emer- gency service providers as well as wireless and satel- lite technologies. In order to provide you with excellent service, calls with the OnStar Center may be monitored or recorded. OnStar Service is: (cid:121) available in the 48 contiguous United States, Alas- ka, Hawaii; (cid:121) available when the vehicle is within the operating range of a cellular provider; (cid:121) subject to limitations caused by atmospheric condi- tions, such as severe weather or topographical condi- tions, such as mountainous terrain; (cid:121) subject to cellular carrier equipment limitations. Global positioning locating capabilities will not be available if satellite signals are obstructed.

6-18

OnStar will not function if the vehicle’s battery is dis- charged or disconnected. It may also be inoperative if the vehicle is in an accident and the OnStar or vehicle electrical system components are damaged. OnStar is the communication link between you and ex- isting governmental emergency and roadside service providers. OnStar will receive your call and use rea- sonable effort to contact an appropriate provider. On- Star cannot promise that the providers will respond in a timely manner or at all. If metallic objects, including roof-mounted accessories or metallic cargo within the accessory, are placed in the immediate vicinity of the OnStar antenna, the an- tenna’s performance will be degraded. This may pre- vent the OnStar system from functioning properly. Therefore, please use caution when installing roof-top accessories to make certain that metallic accessories or metallic objects are not placed in the immediate vi- cinity of the antenna.

Accessory power outlet (cid:132) In the luggage compartment (if

equipped)

UB7008EA

Electrical power (12V DC) from the battery is on tap at the outlet when the ignition switch is either in the “ACC” or “ON” position. You can use an in-car use electrical appliance by con- necting it to the outlet. NOTE The trim cover has a notch through which the con- nected electrical appliance’s cord can be passed.

Interior equipment

(cid:121) Do not attempt to use a cigarette lighter in the accessory power outlet. (cid:121) Do not place any foreign objects, especially metal ones such as coins or aluminum foil, into the accessory power outlet. That could cause a short circuit. Always put the cap on the acces- sory power outlet when it is not in use. (cid:121) Use only electrical appliances which are de- signed for 12V DC and which consume less than 120W. Overloading the accessory power outlet can cause a short circuit. Do not use dou- ble adapters or more than one electrical appli- ance. (cid:121) If the plug on your electric appliance is either too loose or too tight for the accessory power outlet, this can result in a poor contact or cause the plug to get stuck. Only use plugs that fit properly. (cid:121) Use of an electric appliance in the accessory power outlet for a long period of time while the engine is not running can cause battery dis- charge.

– CONTINUED – 6-19

Interior equipment

Convenience hook (cid:132) Coat hook

hand grip.

(cid:132) Shopping bag hook

Never hang anything on the coat hook that might obstruct the driver’s view or that could cause injury in sudden stops or in a collision. And do not hang items on the coat hook that weigh 2.2 lbs (1 kg) or more.

Do not hang items on the shopping bag hook that weigh 2.2 lbs (1 kg) or more.

(cid:84) For sedan models

The coat hook is attached to each rear passenger’s

HS6040BA

6-20

A shopping bag hook is attached to each inner side wall of the trunk near the trunk lid opening.

UBF014CA

(cid:84) For station wagon models

Floor mat (if equipped)

Interior equipment

UB7014BA

A shopping bag hook is attached to each side of the cargo area. To use the hook, push the upper portion and the shop- ping bag hook will appear.

HS6038BA

A retaining pin is located on the driver’s side of the ve- hicle next to the fuel filler door release. The floor mat is secured using the built-in grommet, by placing the grommet over the pin and pushing downward.

– CONTINUED – 6-21

Interior equipment

Luggage cover (if equipped)

Do not place anything on the extended cover. Putting excessive weight on the extended cov- er can break it and an object on the cover could tumble forward in the event of a sudden stop or collision. This could cause serious injury.

HS6039BA

The luggage cover is provided for covering the cargo area and to protect its contents from direct sunlight. This cover is detachable to make room for additional cargo.

Make sure the driver’s floor mat is placed back in its proper location and correctly secured on its retaining pin. If the floor mat slips forward and interferes with the movement of the pedals during driving, it could cause an accident.

6-22

(cid:132) Using the cover

(cid:132) To remove the cover

Interior equipment

UB7015BA

UB7016BA

To extend the cover, pull the end of the cover out of the housing, then insert its hooks into the catches as shown. To rewind it, unhook it from the catches and it will rewind automatically. You should hold on to the cover and guide it back into the cover housing while it is rewinding.

UB7017BA

– CONTINUED – 6-23

Interior equipment

1. Rewind the cover. 2. To take it off the cover rails, lift it out while pressing the release knobs located both sides of the cover housing. 3. Store the cover in the cargo area. To install the cover: Hang the both ends of the cover housing on the cover rails. Make sure that the cover is mounted securely by pulling it up.

Convenient tie-down hooks (if equipped)

The convenient tie-down hooks are designed only for securing light cargo. Never try to se- cure cargo that exceeds the capacity of the hooks. The maximum load capacity is 44 lbs (20
kg) per hook.

The cargo area is equipped with four tie-down hooks

UB7018BA

6-24

so that cargo can be secured with a luggage net or ropes. When using the tie-down hooks, turn them down out of the storing recesses. When not in use, put the hooks up into the storing recesses.

Interior equipment

Subfloor storage (if equipped) The subfloor storage is located under the floor of the trunk or cargo area and can be used to store small items. To open the lid, pull the tab or handle up. NOTE When storing a flat tire, put the subfloor storage in the trunk or cargo area.

(cid:121) Always keep the lid of the subfloor storage closed while driving to reduce the risk of injury in the event of sudden stop or an accident. (cid:121) Do not store spray cans, containers with flammable or corrosive liquids or any other dangerous items in the subfloor storage.

– CONTINUED – 6-25

Interior equipment

(cid:84) Sedan

(cid:84) Station wagon

UB6007BA

UB7019AA

6-26

UB6008BA

Hang the hook provided on the underside of the lid on the rear edge of the roof to keep the lid open.

Interior equipment

– CONTINUED – 6-27

Fuel ................................................................ Fuel requirements ............................................. Fuel filler lid and cap ........................................ State emission testing (U.S. only) ............... Preparing to drive ......................................... Starting the engine ....................................... Starting the engine for a manual transmission vehicle ...................................... Starting the engine for an automatic transmission vehicle ...................................... Starting the engine during cold weather below –4°F (–20°C) ......................................... Starting a flooded engine ................................. Stopping the engine ..................................... Manual transmission .................................... Shifting speeds ................................................. Driving tips ........................................................ (L, L-S, OUTBACK) .................................... Selector lever .................................................... Shift lock release .............................................. SPORTSHIFT mode – 2.5GT, 2.5GTLO) .. Selector lever .................................................... Selection of SPORTSHIFT mode (manual mode) ................................................ Shift lock release .............................................. Rear viscous limited slip differential (LSD) (if equipped) ..............................................

Automatic transmission (with

Automatic transmission

7-2
7-2
7-4
7-7
7-9
7-10
7-10
7-10
7-11
7-11
7-12
7-12
7-13
7-14
7-15
7-16
7-20
7-21
7-22
7-25
7-28
7-29

Starting and operating

VDC (Vehicle Dynamics Control) system

Braking tips ....................................................... Brake system .................................................... Disc brake pad wear warning indicators ........

Power steering .............................................. 7-30
Braking ........................................................... 7-30
7-30
7-31
7-31
ABS (Anti-lock Brake System) ..................... 7-32
ABS system self-check .................................... 7-32
ABS warning light ............................................. 7-33
(if equipped) ............................................... 7-34
VDC system monitor ........................................ 7-36
VDC OFF switch ................................................ 7-38
Parking your vehicle ..................................... 7-40
Cruise control (if equipped) ......................... 7-42
7-43
7-44
7-44
7-45

To set cruise control ........................................ To temporarily cancel the cruise control ....... To turn off the cruise control ........................... To change the cruising speed .........................

7-1

Starting and operating

Starting and operatingFuel

Use of a fuel which is low in quality or use of an inappropriate fuel additive may cause engine damage.

(cid:132) Fuel requirements (cid:84) 2.5 Liter models The 2.5 Liter engine is designed to operate using un- leaded gasoline with an octane rating of 87 AKI or higher. (cid:84) 3.0 Liter models The 3.0 Liter engine is designed to operate using pre- mium unleaded gasoline with an octane rating of 91
AKI or higher. Regular unleaded gasoline with an oc- tane rating of 87 AKI may be used if necessary. For optimum engine performance and driveability, it is rec- ommended that you use premium grade unleaded gasoline. (cid:84) Fuel octane rating This octane rating is the average of the Research Oc-

7-2

tane and Motor Octane numbers and is commonly re- ferred to as the Anti Knock Index (AKI). Using a gasoline with a lower octane rating can cause persistent and heavy knocking, which can damage the engine. Do not be concerned if your vehicle some- times knocks lightly when you drive up a hill or when you accelerate. See your dealer or a qualified service technician if you use a fuel with the specified octane rating and your vehicle knocks heavily or persistently. (cid:84) Unleaded gasoline The neck of the fuel filler pipe is designed to accept only an unleaded gasoline filler nozzle. Under no cir- cumstances should leaded gasoline be used because it will damage the emission control system and may impair driveability and fuel economy. (cid:84) California fuel If your vehicle was certified to California Emission Standards as indicated on the underhood tune-up la- bel. It is designed to optimize engine and emission control system performance with gasoline that meets the clean burning low-sulfur California gasoline speci- fications. If you live in any other state than California, your vehicle will operate on gasoline meeting Federal specifications. Gasoline sold outside California is per- mitted to have higher sulfur levels, which may affect the performance of your vehicle’s catalytic converter

and may produce a sulfur exhaust odor or smell. SUBARU recommends that you try a different brand of unleaded gasoline having lower sulfur to determine if the problem is fuel related before returning your vehi- cle to an authorized dealer for service. The CHECK ENGINE warning light/Malfunction indicator lamp may also turn on. If this occurs, return to your authorized SUBARU dealer for diagnosis. If it is determined that the condition is caused by the type of fuel used, re- pairs may not be covered by your warranty. (cid:84) MMT Some gasoline contains an octane-enhancing additive called MMT (Methylcyclopentadienyl Manganese Tri- carbonyl). If you use such fuels, your emission control system performance may deteriorate and the CHECK ENGINE warning light/Malfunction indicator lamp may turn on. If this happens, return to your authorized SUBARU Dealer for service. If it is determined that the condition is caused by the type of fuel used, repairs may not be covered by your warranty. (cid:84) Gasoline for cleaner air

Do not let fuel spill on the exterior surfaces of the vehicle. Fuels containing alcohol may

Starting and operating

cause paint damage, which is not covered un- der the SUBARU Limited Warranty.

Your use of gasoline with detergent additives will help prevent deposits from forming in your engine and fuel system. This helps keep your engine in tune and your emission control system working properly, and is a way of doing your part for cleaner air. If you continu- ously use a high quality fuel with the proper detergent and other additives, you should never need to add any fuel system cleaning agents to your fuel tank. Many gasolines are now blended with materials called oxygenates. Use of these fuels can also help keep the air cleaner. Oxygenated blend fuels, such as MTBE (Methyl Tertiary Butyl ether) or ethanol (ethyl or grain alcohol) may be used in your vehicle, but should con- tain no more than 15% MTBE or 10% ethanol for the proper operation of your SUBARU. In addition, some gasoline suppliers are now produc- ing reformulated gasolines, which are designed to re- duce vehicle emissions. SUBARU approves the use of reformulated gasoline. If you are not sure what the fuel contains, you should ask your service station operators if their gasolines contain detergents and oxygenates and if they have – CONTINUED – 7-3

Starting and operating

been reformulated to reduce vehicle emissions. As additional guidance, only use fuels suited for your vehicle as explained below. (cid:121) Fuel should be unleaded and have an octane rating no lower than that specified in this manual. (cid:121) Methanol (methyl or wood alcohol) is sometimes mixed with unleaded gasoline. Methanol can be used in your vehicle ONLY if it does not exceed 5% of the fuel mixture AND if it is accompanied by sufficient quantities of the proper cosolvents and corrosion in- hibitors required to prevent damage to the fuel system. Do not use fuel containing methanol EXCEPT under these conditions. (cid:121) If undesirable driveability problems are experienced and you suspect they may be fuel related, try a differ- ent brand of gasoline before seeking service at your SUBARU dealer. (cid:121) Fuel system damage or driveability problems which result from the use of improper fuel are not covered under the SUBARU Limited Warranty.

(cid:132) Fuel filler lid and cap (cid:84) Refueling

Sedan

UBF013DA

7-4

Starting and operating

Station wagon

UB3007BA

UG7502BA

1. To open the fuel filler lid, pull the lid release lever up.

– CONTINUED – 7-5

Starting and operating

UB7030BB

1) Open 2) Close 2. Remove the fuel filler cap by turning it slowly coun- terclockwise.

(cid:121) Gasoline vapor is highly flammable. Before refueling, always first stop the engine and make sure that there are no lighted cigarettes, open flames or electrical sparks in the adjacent area. (cid:121) When opening the cap, do not remove the cap quickly. Fuel may be under pressure and spray out of the fuel filler neck especially in hot

7-6

weather, which may cause injury.

3. Stop filling the tank after the fuel filler pump auto- matically clicks off. Do not add any more fuel. 4. Put the cap back on, turn it clockwise until you hear a clicking noise. Be certain not to catch the tether un- der the cap while tightening. 5. Close the fuel filler lid completely. If you spill any fuel on the painted surface, rinse it off immediately. Otherwise, the painted surface could be damaged. NOTE

HS3023AA

(cid:121) You will see the “FUEL DOOR ” sign in the combination meter. This indicates that the fuel fill- er door (lid) is located on the right side of the ve- hicle. (cid:121) If the fuel filler cap is not tightened until it clicks or if the tether is caught under the cap, the CHECK ENGINE warning light may come on. Refer to the “Warning and indicator lights” section located in chapter 3.

(cid:121) Never add any cleaning agents to the fuel tank. The addition of a cleaning agent may cause damage to the fuel system. (cid:121) Make sure that the cap is tightened until it clicks to prevent fuel spillage in the event of an accident. (cid:121) Do not let fuel spill on the exterior surfaces of the vehicle. Fuels may cause paint damage, which is not covered under the SUBARU Limit- ed Warranty. (cid:121) Always use a genuine SUBARU fuel filler cap. If you use the wrong cap, it may not fit or have proper venting, and your fuel tank and emis- sion control system might be damaged.

Starting and operating

State emission testing (U.S. only)

Testing of an All-Wheel Drive vehicle must NEVER be performed on a single two-wheel dy- namometer. Attempting to do so will result in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby.

Resultant vehicle damage due to improper test- ing is not covered under the SUBARU Limited Warranty and is the responsibility of the state inspection program or its contractors or licens- ees.

At state inspection time, remember to tell your in- spection or service station in advance not to place your SUBARU AWD vehicle on a two-wheel dyna- mometer. Otherwise, serious transmission dam- age will result. Some states have started using dynamometers in their state inspection programs in order to meet their – CONTINUED – 7-7

Starting and operating

obligation under federal law to implement stricter vehi- cle emission standards to reduce air pollution from cars. A dynamometer is a treadmill or roller-like testing device that allows your car’s wheels to turn while the car remains in one place. Depending on the severity of a state’s air pollution problems, the states must adopt either a “basic” or “enhanced” vehicle emission in- spection test. Normally, a portion of the basic emission test consists of an emission inspector inserting an an- alyzer probe into the exhaust pipe of an idling vehicle for a short period of time. States with more severe air pollution problems are required to adopt an enhanced vehicle emission test. This test simulates actual driv- ing conditions on a dynamometer and permits more accurate measurement of tailpipe emitted pollution than the basic emission test. The U.S. Environmental Protection Agency (EPA) and states using two-wheel dynamometers in their emis- sion testing programs have EXEMPTED SUBARU AWD vehicles from the portion of the testing program that involves a two-wheel dynamometer. There are some states that use four-wheel dynamom- eters in their testing programs. When properly used, that equipment will not damage an AWD SUBARU ve- hicle. Under no circumstances should the rear wheels be

7-8

jacked off the ground, nor should the driveshaft be dis- connected for state emission testing. The EPA has issued regulations for inspecting the On- Board Diagnostic (OBD) system as part of the state emissions inspection. The OBD system is designed to detect engine and transmission problems that might cause vehicle emissions to exceed allowable limits. These inspections apply to all 1996 model year and newer passenger cars and light trucks. Several states plus the District of Columbia have opted to start the OBD system inspection prior to the required EPA reg- ulation effective date of January 1, 2002. Other states will add OBD system inspection in 2002. (cid:121) The inspection of the OBD system consists of a vi- sual operational check of the “CHECK ENGINE” warn- ing light/malfunction indicator lamp (MIL) and an ex- amination of the OBD system with an electronic scan tool while the engine is running. (cid:121) A vehicle passes the OBD system inspection if proper the “CHECK ENGINE” warning light/MIL illumi- nation is observed, there is no stored diagnostic trou- ble codes, and the OBD system readiness monitors are complete. (cid:121) A vehicle fails the OBD inspection if the “CHECK ENGINE” warning light/MIL is not properly operating or there is one or more diagnostic trouble codes stored

in vehicle’s computer with the “CHECK ENGINE” warning light/MIL illuminated. (cid:121) A state emission inspection may reject (not pass or fail) a vehicle if the number of OBD system readiness monitors “Not Ready” is greater than three. Under this condition, the vehicle operator should be instructed to drive his/her vehicle for a few days to set the monitors and return for an emission re-inspection. (cid:121) Owners of rejected or failing vehicles should contact their SUBARU Dealer for service.

Starting and operating

Preparing to drive You should perform the following checks and adjust- ments every day before you start driving. 1. Check that all windows, mirrors, and lights are clean and unobstructed. 2. Check the appearance and condition of the tires. Also check tires for proper inflation. 3. Look under the vehicle for any sign of leaks. 4. Check that the hood, trunk and rear gate are fully closed. 5. Check the adjustment of the seat. 6. Check the adjustment of the inside and outside mir- rors. 7. Fasten your seatbelt. Check that your passengers have fastened their seatbelts. 8. Check the operation of the warning and indicator lights when the ignition switch is turned to the “ON” po- sition. 9. Check the gauges, indicator and warning lights af- ter starting the engine. NOTE Engine oil, engine coolant, brake fluid, washer flu- id and other fluid levels should be checked daily, weekly or at fuel stops.

– CONTINUED – 7-9

Starting and operating

Starting the engine

Do not operate the starter motor continuously for more than ten seconds. If the engine fails to start after operating the starter for five to ten seconds, wait for ten seconds or more before trying again.

(cid:132) Starting the engine for a manual trans-

mission vehicle

1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. Press the clutch pedal to the floor and shift the shift lever into neutral. Hold the clutch pedal to the floor while starting the en- gine. The starter motor will only operate when the clutch pedal is pressed fully to the floor. 4. Turn the ignition switch to the “ON” position and check the operation of the warning and indicator lights. Refer to the “Warning and indicator lights” section (chapter 3). 5. Turn the ignition switch to the “START” position without depressing the accelerator pedal. Release

7-10

the key immediately after the engine has started. If the engine does not start within ten seconds, wait a while and then turn the ignition switch to the “START” position again while depressing the accelerator pedal half way down. 6. Confirm that all warning and indicator lights have gone off after the engine has started. The fuel injection system automatically lowers the idle speed as the en- gine warms up.

(cid:132) Starting the engine for an automatic

transmission vehicle

If you restart the engine while the vehicle is moving, shift the selector lever into the “N” po- sition. Do not attempt to place the selector lever of a moving vehicle into the “P” position.

1. Apply the parking brake. 2. Turn off unnecessary lights and accessories. 3. Shift the selector lever to the “P” or “N” position (preferably “P” position). The starter will only operate when the select lever is at the “P” or “N” position. 4. Turn the ignition switch to the “ON” position and

Starting and operating

(cid:132) Starting a flooded engine If the engine does not start, it may be flooded (exces- sive fuel in the engine). In case of a flooded engine, turn the starter motor for five seconds with the accelerator pedal fully de- pressed. Repeat this two or three times until the en- gine starts. Release the ignition switch and accelera- tor pedal as soon as the engine starts.

check the operation of the warning and indicator lights. Refer to the “Warning and indicator lights” section (chapter 3). 5. Turn the ignition switch to the “START” position without depressing the accelerator pedal. Release the key immediately after the engine has started. If the engine does not start within ten seconds, wait a while and then turn the ignition switch to the “START” position again while depressing the accelerator pedal half way down. 6. Confirm that all warning and indicator lights have gone out after the engine has started. The fuel injec- tion system automatically lowers the idle speed as the engine warms up. While the engine is warming up, make sure that the selector lever is at the “P” or “N” position and that the parking brake is applied.

(cid:132) Starting the engine during cold weath-

er below –4°F (–20°C)

If the engine is difficult to start using the normal meth- od (without depressing the accelerator pedal), turn the ignition switch to the “START” position while slightly depressing the accelerator pedal.

– CONTINUED – 7-11

Starting and operating

Stopping the engine

Manual transmission

Do not stop the engine when the vehicle is mov- ing. This will cause loss of power to the power steering and the brake booster, making steer- ing and braking more difficult. It could also re- sult in accidental activation of the “LOCK” po- sition on the ignition switch, causing the steer- ing wheel to lock.

The ignition switch should be turned off only when the engine is idling.

Do not drive the vehicle with the clutch disen- gaged (i.e., when the clutch pedal is depressed) or with the shift lever in the neutral position. Engine braking has no effect in either of these conditions and the risk of an accident is conse- quently increased.

Shift into reverse ONLY when the vehicle has completely stopped. It may cause damage to the transmission to try shifting into reverse when the vehicle is moving.

The manual transmission is a fully synchromeshed 5- forward and 1-reverse speed transmission.