2012 Subaru Forester Owners Manual

not installed. One of them must always be installed on the vehi- cle.

. If a trailer hitch is installed, it is not possible to install the rear towing hook.

When you tow a trailer, refer to “Trailer towing” F8-18.

& Connecting a trailer 1. Remove the receiver cover from the hitch receiver tube. Then insert the ball mount into the hitch receiver tube.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (311,1)

Driving tips 8-17

does not come off the hitch receiver.

WARNING

Do not connect safety chains to part of the vehicle other than the safety chain hooks.

2. Insert the hitch pin into the hole on the hitch receiver tube so that the pin passes through the ball mount.

1) Hitch ball installation point 2) Hooks for safety chains

5. Use only a hitch ball that is appropriate for the ball mount and your trailer. The hitch ball must be securely installed on the ball mount. 6. Connect your trailer to the hitch ball. 7. Connect the trailer and the hitch with safety chains that will hold the trailer’s maximum gross weight. The chains should cross under the trailer tongue to prevent the tongue from dropping onto the ground in case it should disconnect from the hitch ball. Allow sufficient slack in the turn situations into chains taking tight account; however, be careful not to let them drag on the ground.

Hitch harness connector

8. Connect the hitch wire harness’s black four-pin wire connector to the towing trailer’s wire harness 9. Confirm proper function of the hitch wire harness by individually activating the brake, stop, and turn signal lights on the trailer.

NOTE Always disconnect the trailer wire har- ness before launching or retrieving a

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

3. hitch pin. 4. Pull

Insert the safety pin securely into the

the ball mount

to make sure it

8-18 Driving tips

watercraft. & When you do not tow a trailer . Remove the ball mount from the hitch receiver tube and insert the receiver cover onto the hitch receiver tube. . Place the dust cap over the four-pin connector of the hitch wire harness to protect against possible damage. . Occasionally lubricate terminals of the four-pin connector using terminal grease.

Black plate (312,1)

Trailer towing

Your vehicle is designed and intended to be used primarily as a passenger-carrying vehicle. Towing a trailer puts additional loads on your vehicle’s engine, drivetrain, brakes, tires and suspension and has an adverse effect on fuel economy. If you do decide to tow a trailer, your safety and satisfaction depend upon proper use of correct equipment and cautious opera- tion of your vehicle. Seek the advice of your SUBARU dealer to assist you in purchasing a hitch and other necessary towing equipment appropriate for your vehicle. In addition, be sure to follow the instructions on correct installation and use provided by the trailer and other towing equipment manufacturers. SUBARU assumes no responsibility for injuries or vehicle damage that result from trailer from any errors or omissions in the instructions accompanying such equipment or for your failure to follow the proper instructions.

towing equipment, or

& Warranties and maintenance SUBARU warranties do not apply to vehicle damage or malfunction caused by trailer towing. If you use your vehicle to tow a trailer, more frequent maintenance will be required due to the additional load.

(Refer to “Maintenance schedule under severe driving conditions” in the “Warranty and Maintenance Booklet”.) Under no circumstances should a trailer be towed with a new vehicle or a vehicle with any new powertrain component (en- gine, transmission, differential, wheel bearings, etc.) for the first 1,000 miles (1,600 km) of driving.

& Maximum load limits

WARNING

Never exceed the maximum load limits explained in the following. Exceeding the maximum load limits could cause personal injury and/or vehicle damage.

CAUTION

. Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight.

. Before towing a trailer, check the trailer total weight, GVW, GAWs and tongue load. Make sure the load and its distribution in your vehicle and trailer are accepta-

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

ble.

! Total trailer weight

Total trailer weight

The total trailer weight (trailer weight plus its cargo load) must never exceed the maximum weight shown in the following table.

Maximum total trailer

weight

1,000 lbs (453 kg)

2,400 lbs (1,087 kg) 1,000 lbs (453 kg)

2,400 lbs (1,087 kg) 1,000 lbs (453 kg)

Model

Conditions

MT models When towing a

trailer without brakes.

When towing a trailer with brakes.

AT models When towing a

trailer without brakes.

When towing a trailer with brakes.

When towing a trailer on a long uphill grade con- tinuously for over 5 miles (8 km) with an outside tem- perature of 1048F (408C) or above.

Black plate (313,1)

Driving tips 8-19

! Gross Vehicle Weight (GVW) and

Gross Vehicle Weight Rating (GVWR)

Gross Vehicle Weight

(GVW)

The Gross Vehicle Weight (GVW) must never exceed the Gross Vehicle Weight Rating (GVWR). Gross Vehicle Weight is the combined total of the weight of the vehicle, driver, passengers, luggage, trailer hitch, trailer tongue load and any other optional equipment installed on your vehicle. Therefore, the GVW changes depending on the situation. Determine the GVW each time before going on a trip by putting your vehicle and trailer on a vehicle scale.

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (314,1)

8-20 Driving tips

! Gross Axle Weight (GAW) and

Gross Axle Weight Rating (GAWR)

! Tongue load

Certification label

GVWR is shown on the certification label located on the driver’s side door jamb.

Gross Axle Weight

The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehi- cle. The front and rear GAWR are also shown on the certification label. To check both GVWR and GAWR and to confirm that the total weight and weight distribution are within safe driving limits, you should have your vehicle and trailer weighed at a commercial weighing station. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.

Tongue load

Ensure that the trailer tongue load is from 8 to 11 percent of the total trailer weight and does not exceed the maximum value of 200 lbs (90 kg).

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (315,1)

Driving tips 8-21

the rear axle of the towing vehicle. This may cause the rear wheels to skid, especially during braking or when vehicle speed is reduced dur- ing cornering, resulting in over- steer, spin out and/or jackknifing.

& Trailer hitches

WARNING

Never drill the frame or under-body of your vehicle to install a commer- cial trailer hitch. If you do, danger- ous exhaust gas, water or mud may enter the passenger compartment through the drilled hole. Exhaust gas contains carbon monoxide, a colorless and odorless gas which is dangerous, or even lethal, if inhaled. Also, drilling the frame or under- body of your vehicle could cause deterioration of strength of your vehicle and cause corrosion around the drilled hole.

CAUTION

. Do not modify the vehicle ex- haust system, brake system, or other systems when installing a – CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Jack

1) 2) Bathroom scale

The tongue load can be weighed with a bathroom scale as shown in the illustration above. When weighing the tongue load, be sure to position the towing coupler at the height at which it would be during actual towing, using a jack as shown.

F:

Front of vehicle

The tongue load can be adjusted by proper distribution of the load in the trailer. Never load the trailer with more weight in the back than in the front; approximately 60 percent of the trailer load should be in the front and approximately 40 percent in the rear. Also, distribute the load as evenly as possible on both the left and right sides. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.

WARNING

If the trailer is loaded with more weight in the back of trailer’s axle than in the front, the load is taken off

Black plate (316,1)

8-22 Driving tips

hitch or other trailer towing equipment.

. Do not use axle-mounted hitches as they can cause damage to the axle housing, wheel bearings, wheels or tires.

Choose a proper hitch for your vehicle and trailer. The use of a genuine SUBARU trailer hitch is recommended. A genuine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoid- able, be sure the hitch is suited to your vehicle and trailer. Consult with a profes- sional hitch supplier to assist you in choosing an appropriate hitch for your vehicle. Be sure to follow all of the hitch manufacturer’s instructions for installation and use. Never use a hitch that mounts only to the rear bumper. The bumper is not designed to handle that type of load. For all types of hitches, regularly check that the hitch mounting bolts and nuts are tight.

& Connecting a trailer ! Trailer brakes

! Trailer safety chains

WARNING

WARNING

. Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight.

. Do not directly connect your trailer’s hydraulic brake system to the hydraulic brake system in your vehicle. Direct connection would cause the vehicle’s brake performance to deteriorate and could lead to an accident.

the trailer

If your trailer’s total weight (trailer weight plus its cargo weight) exceeds 1,000 lbs (453 kg), is required to be equipped with its own brake system. Electric brakes or surge brakes are recommended, and must be installed properly. Check that your trailer’s brakes conform with Federal, state/province and/ or other applicable regulations. Your SUBARU’s brake system is not designed to be tapped into the trailer’s hydraulic brake system. Please ask your SUBARU dealer and professional trailer supplier for more information about the trailer’s brake system.

Always use safety chains between your vehicle and the trailer. Towing a trailer without safety chains could create a traffic safety hazard if the trailer separates from the hitch due to coupling damage or hitch ball damage.

In case the trailer hitch connector or hitch ball should break or become discon- nected, the trailer could get loose and create a traffic safety hazard. For safety, always connect the towing vehicle and trailer with trailer safety chains. Pass the chains crossing each other under the trailer tongue to prevent the trailer from dropping onto the ground in case the trailer tongue should discon- nect from the hitch ball. Allow sufficient slack in the chains taking tight turn situations into account; however, be care- ful not to let them drag on the ground. For more information about the safety chain connection, refer to the instructions for your hitch and trailer.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

! Side mirrors

Black plate (317,1)

Driving tips 8-23

Connection of trailer lights to your vehi- cle’s electrical system requires modifica- tions to the vehicle’s lighting circuit to increase its capacity and accommodate wiring changes. To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the brake lights and turn signal lights each time you hitch up. ! Tires

accordance with the trailer manufacturer’s specifications.

In the event your vehicle gets a flat tire when towing a trailer, ask a commercial road service to repair the flat tire.

If you carry a regular size spare tire in your vehicle or trailer as a precaution against getting a flat tire, be sure that the spare tire is firmly secured.

WARNING

& Trailer towing tips

After hitching a trailer to your vehicle, check that the standard side mirrors provide a good rearward field of view without significant blind spots. If significant blind spots occur with the vehicle’s stan- dard side mirrors, use towing mirrors that conform with Federal, state/province and/ or other applicable regulations. ! Trailer lights

CAUTION

Direct splicing or other improper connection of trailer lights may damage your vehicle’s electrical system and cause a malfunction of your vehicle’s lighting system.

Never tow a trailer when the tem- porary spare tire is used. The tem- porary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle.

Make sure that all the tires on your vehicle are properly inflated.

The recommended cold tire pressure under trailer towing conditions is shown in “Tires” F12-10. Adjust tire pressure to the recommended pressure when the tires are cold. Normal pressure should be maintained in the front tires.

the rear

Trailer tire condition, size, load rating and proper inflation pressure should be in

WARNING

. Never exceed 45 mph (72 km/h) when towing a trailer in hilly country on hot days.

. When towing a trailer, steering, stability, stopping distance and braking performance will be dif- ferent from normal operation. For safety’s sake, you should employ extra caution when towing a trailer and you should never drive at excessive speeds. You should also keep the following tips in mind:

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

8-24 Driving tips

! Before starting out on a trip . Check that the vehicle and vehicle-to- hitch mounting are in good condition. If any problems are apparent, do not tow the trailer. . Check that the vehicle sits horizontally with the trailer attached. If the vehicle is tipped sharply up at the front and down at the rear, check the total trailer weight, GVW, GAWs and tongue load again, then confirm that the load and its distribution are acceptable. . Check that correct. . Check that the vehicle and trailer are connected properly. Confirm that:

the tire pressures are

tongue is connected

– The trailer properly to the hitch ball. – The trailer lights connector is con- nected properly and trailer’s brake lights illuminate when the vehicle’s is pressed, and that the brake pedal trailer’s turn signal lights flash when the vehicle’s turn signal lever is oper- ated. – The safety chains are connected properly. – All cargo in the trailer is secured safely in position. – The side mirrors provide a good rearward field of view without a sig-

nificant blind spot.

. Sufficient time should be taken to learn the “feel” of the vehicle/trailer combination before starting out on a trip. In an area free of traffic, practice turning, stopping and backing up. ! Driving with a trailer . You should allow for considerably more stopping distance when towing a trailer. Avoid sudden braking because it may result in skidding or jackknifing and loss of control. . Avoid abrupt starts and sudden accel- erations. If your vehicle has a manual transmission, always start out in first gear and release the clutch at moderate engine revolution. . Avoid uneven steering, sharp turns and rapid lane changes. . Slow down before turning. Make a longer than normal turning radius because the trailer wheels will be closer than the vehicle wheels to the inside of the turn. In a tight the trailer could hit your vehicle. . Crosswinds will adversely affect the handling of your vehicle and trailer, caus- ing sway. Crosswinds can be due to weather conditions or the passing of large trucks or buses. If swaying occurs, firmly grip the steering wheel and slow down

turn,

Black plate (318,1)

immediately but gradually. . When passing other vehicles, consid- erable distance is required because of the added weight and length caused by attaching the trailer to your vehicle.

Left turn

1) 2) Right turn . Backing up with a trailer is difficult and takes practice. When backing up with a trailer, never accelerate or steer rapidly. When turning back, grip the bottom of the steering wheel with one hand and turn it to the left for a left turn, and turn it to the right for a right turn. . If illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed immediately by the nearest SUBARU dealer.

the ABS warning light

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

! Driving on grades . Before going down a steep hill, slow down and shift into lower gear (if neces- sary, use 1st gear) in order to utilize the engine braking effect and prevent over- heating of your vehicle’s brakes. Do not make sudden downshifts. . When driving uphill in hot weather, the air conditioner may turn off automatically to protect the engine from overheating. . When driving uphill in hot weather, pay attention to the following indicators be- cause the engine and transmission are relatively prone to overheating.

– Temperature gauge (if equipped) – Coolant temperature high warning light (if equipped) – AT OIL TEMP warning light models)

(AT

. If any of the following conditions occur, immediately turn off the air conditioner and stop the vehicle in the nearest safe location. Refer to “If you park your vehicle in case of an emergency” F9-2 and “Engine overheating” F9-13.

– Temperature gauge needle ap- proaches the OVERHEAT zone (if to “Temperature equipped). Refer gauge (models with type A combina- tion meter)” F3-11. – Coolant temperature high warning light illuminates (if equipped). Refer to

temperature low indicator temperature high warn-

“Coolant light/Coolant ing light” F3-16. – AT OIL TEMP warning light illumi- nates (AT models). Refer to “AT OIL TEMP warning light (AT models)” F3- 18.

. If your vehicle has an automatic trans- mission, avoid using the accelerator pedal to stay stationary on an uphill slope instead of using the parking brake or foot brake. That may cause the transmission fluid to overheat. . If your vehicle has an automatic trans- mission, place the select lever as follows. Uphill slopes: “D” position Downhill slopes: A low-speed gear posi- tion to use engine braking ! Parking on a grade Always block the wheels under both vehicle and trailer when parking. Apply the parking brake firmly. You should not park on a hill or slope. But if parking on a hill or slope cannot be avoided, you should take the following steps. 1. Press and hold the brake pedal. 2. Have someone place chocks under both the vehicle and trailer wheels. 3. When the chocks are in place, release the brake pedal slowly until the chocks absorb the load.

Black plate (319,1)

Driving tips 8-25

4. Press the brake pedal fully and then apply the parking brake; slowly release the brake pedal. 5. Shift into 1st or reverse gear (manual transmission models) or the “P” position (automatic transmission models) and shut off the engine.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22

If you park your vehicle in case of an

emergency ........................................................ Temporary spare tire (if equipped) ....................

Precautions for AWD models with automatic

transmission ..................................................... Maintenance tools ............................................... Tool bag.............................................................. Under the cargo area........................................... Flat tires............................................................... Changing a flat tire.............................................. Tire pressure monitoring system (TPMS)

9-2
9-2

9-3
9-4
9-4
9-5
9-6
9-6

(U.S.-spec. models) ...........................................

9-9
Jump starting ..................................................... 9-10
9-11

How to jump start...............................................

Black plate (17,1)

In case of emergency

Engine overheating ...........................................

9-13

If steam is coming from the engine

compartment ...................................................

If no steam is coming from the engine

compartment ................................................... Towing ................................................................ Towing and tie-down hooks................................ Using a flat-bed truck......................................... Towing with all wheels on the ground.................

Rear gate – if the rear gate cannot be

opened.............................................................

Moonroof – if the moonroof cannot be

closed ..............................................................

9-13

9-13
9-14
9-14
9-17
9-17

9-18

9-19

北米Model "A8170BE-A" EDITED: 2011/ 6/ 6

Black plate (322,1)

9-2 In case of emergency

If you park your vehicle in case of an emergency

NOTE When the hazard warning flasher is on, the turn signals do not work.

Temporary spare tire (if equipped)

The hazard warning flasher should be used during the daytime and nighttime to warn other drivers when you have to park your vehicle under emergency conditions. Avoid stopping on the road. It is best to safely pull off the road if a problem occurs.

The hazard warning flasher can be acti- vated regardless of the ignition switch position. Turn on the hazard warning flasher by pushing the hazard warning flasher switch. Turn it off by pushing the switch again.

WARNING

When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will illuminate steadily after blinking for approxi- mately one minute. This indicates the tire pressure monitoring system (TPMS) is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/or sys- tem resetting.

CAUTION

Never use any temporary spare tire other than the original. Using other sizes may result in severe mechan- ical damage to the drive train of your vehicle.

The temporary spare tire is smaller and lighter tire and is designed for emergency use only. Re- move the temporary spare tire and re-

than a conventional

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

the conventional

install possible.

tire as soon as

Check the inflation pressure of the tem- porary spare tire periodically to keep the tire ready for use. The correct pressure is 60 psi (420 kPa, 4.2 kg/cm2).

When using the temporary spare tire, note the following. . Do not exceed 50 mph (80 km/h). . Do not put a tire chain on the temporary spare tire. Because of the smaller tire size, a tire chain will not fit properly. . Do not use two or more temporary spare tires at the same time. . Do not drive over obstacles. This tire has a smaller diameter, so road clearance is reduced.

Tread wear indicator bar Indicator location mark

1) 2) . When the wear indicator appears on the tread, replace the tire. . The temporary spare tire must be used only on a rear wheel. If a front wheel tire gets punctured, replace the wheel with a rear wheel and install the temporary spare tire in place of the removed rear wheel.

Black plate (323,1)

In case of emergency 9-3

& Precautions for AWD models with automatic transmission Your vehicle is equipped with the AWD (All-Wheel Drive) system. if your vehicle is an AT model, before driving your vehicle with the temporary spare tire, deactivate the AWD capability of the vehicle as follows. 1. Turn the ignition switch to the “LOCK” position.

In addition,

the 2. Pull any one spare fuse out of spare fuse holder at the back side of the main fuse box cover in the engine compartment. You may use any one fuse in the spare fuse holder.

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (324,1)

9-4 In case of emergency

Maintenance tools

& Tool bag

Your vehicle is equipped with the following maintenance tools: . Jack . Jack handle . Screwdriver . Towing hook (eye bolt) . Wheel nut wrench . Wheel cover with wheel covers)

(only models

remover

1) Spare fuse 2)

FWD connector

3. Put a spare fuse inside the FWD connector located in the cabin and confirm the All-Wheel Drive warning light that “ illuminates. The All-Wheel-Drive capability of the vehicle has now been deactivated.

”

NOTE After reinstalling the conventional tire, remove the spare fuse from the FWD connector in order to reactivate All- Wheel Drive. Make sure to restore the removed spare fuse in the spare fuse holder located on the back side of the main fuse box cover.

1) Screwdriver 2) Wheel nut wrench 3) 4) Wheel cover remover (only models with

Tool bag

wheel covers)

The screwdriver and wheel nut wrench are stored in the tool bag.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

& Under the cargo area

Black plate (325,1)

In case of emergency 9-5

recess of the spare tire wheel.

the tools in the tool bag can be

Also, stored in the tool bucket as illustrated. For how to use the jack, refer to “Flat tires” F9-6.

1) Under-floor storage compartment

(if equipped) (Refer to “Under-floor storage compartment” F6-16) Jack handle Tool bucket

2) 3) 4) Spare tire

1) Wheel nut wrench 2) Screwdriver 3) 4)

Jack Towing hook (eye bolt)

The jack handle is stored under the cargo floor. The jack and towing hook are stored in the tool bucket that is located in the

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

9-6 In case of emergency

Flat tires

If you have a flat tire while driving, never brake suddenly; keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place.

& Changing a flat tire

WARNING

. Do not jack up the vehicle on an incline or a loose road surface. The jack can come out of the jacking point or sink into the ground and this can result in a severe accident.

. Use only the jack provided with your vehicle. The jack supplied with the vehicle is designed only for changing a tire. Never get under the vehicle while support- ing the vehicle with this jack.

. Always turn off the engine before raising the flat tire off the ground using the jack. Never swing or push the vehicle supported with the jack. The jack can come out of the jacking point due to a jolt and this can result in a severe accident.

1. Park on a hard, level surface, when- ever possible, then stop the engine. 2. Apply the parking brake securely and shift the shift lever in reverse (MT models) or the select lever in the “P” (Park) position (AT models). 3. Turn on the hazard warning flasher and have everyone get out of the vehicle.

Black plate (326,1)

the jack,

jack handle and

5. Take out wheel nut wrench. The tools and the spare tire are stored under the floor of the cargo area. Refer to “Maintenance tools” F9-4. NOTE Make sure that the jack is well lubri- cated before using it.

Models with standard spare tire

4. Put chocks at the front and rear of the tire diagonally opposite the flat tire.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (327,1)

In case of emergency 9-7

8. Loosen the wheel nuts using the wheel nut wrench but do not remove the nuts.

Models with temporary spare tire

6. Take out the tool bucket and turn the attaching bolt counterclockwise, then take the spare tire out. NOTE If the spare tire provided in your vehicle is a temporary spare tire, carefully read “Temporary spare tire” F9-2 and strictly follow the instructions.

1) Notch 2) Valve hole

7. If your vehicle has wheel covers, insert a wheel cover remover into the notch on the opposite side of the valve hole and pry the wheel cover to remove it.

9. Place the jack under the side sill at the front or rear jack-up point closest to the flat tire. Turn the jackscrew by hand until the jack head engages firmly into the jack-up point.

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

9-8 In case of emergency

Black plate (328,1)

10. Insert the jack handle into the jack- screw, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary. 11. Remove the wheel nuts and the flat tire.

12. Before putting the spare tire on, clean the mounting surface of the wheel and hub with a cloth. 13. Put on the spare tire. Replace the wheel nuts. Tighten them by hand.

WARNING

Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident.

14. Turn the jack handle counterclockwise to lower the vehicle.

15. Use the wheel nut wrench to securely tighten the wheel nuts to the specified torque, following the tightening order in the illustration. For the wheel nut tightening torque, refer to “Tires” F12-10. Never use your foot on the wheel nut wrench or a pipe extension on the wrench because you may exceed the specified torque. Have the wheel nut torque checked at the nearest automotive service facility.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

& Tire pressure monitoring

system (TPMS) (U.S.-spec. models)

16. Store the flat tire in the spare tire compartment. Put in the spacer and tight- en the attaching bolt firmly. Also store the jack, jack handle and wheel nut wrench in their storage locations.

Type A

WARNING

Never place a tire or tire changing tools in the passenger compartment after changing wheels. In a sudden stop or collision, loose equipment could strike occupants and cause injury. Store the tire and all tools in the proper place.

Type B

The tire pressure monitoring system pro-

Black plate (329,1)

In case of emergency 9-9

that

vides the driver with the warning message indicated by sending a signal from a sensor is installed in each wheel when tire pressure is severely low. The tire pressure monitoring system will activate only when the vehicle is driven. Also, this system may not react immedi- ately to a sudden drop in tire pressure (for example, a blow-out caused running over a sharp object).

WARNING

If the low tire pressure warning light illuminates while driving, never brake suddenly and keep driving straight ahead while gradually redu- cing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehicle damage and serious personal injury could occur. Check the pressure for all four tires and adjust the pressure to the COLD tire pressure shown on the vehicle placard on the door pillar on the driver’s side. If this light still illumi- nates while driving after adjusting the tire pressure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

9-10 In case of emergency

it with a spare tire as soon as possible. When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will illuminate steadily after blinking for approxi- mately one minute. This indicates the TPMS is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/ or system resetting. Do not inject any tire liquid or aerosol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light illuminates steadily after blinking for approximately one min- ute, promptly contact a SUBARU dealer to have the system inspected.

Black plate (330,1)

Jump starting

WARNING

. Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the vehicle. If battery fluid gets on you, thoroughly flush the exposed area with water immediately. Get medical help if the fluid has entered your eyes. If battery fluid is accidentally swallowed, immediately drink a large amount of milk or water, and obtain immediate medical help. Keep everyone including chil- dren away from the battery.

. The gas generated by a battery explodes if a flame or spark is brought near it. Do not smoke or light a match while jump starting. . Never attempt jump starting if the discharged battery is frozen. It could cause the battery to burst or explode.

. Whenever working on or around a battery, always wear suitable

eye protectors, and remove metal objects such as rings, bands or other metal jewelry.

. Be sure the jumper cables and clamps on them do not have loose or missing insulation. Do not jump start unless cables in suitable condition are avail- able.

. A running engine can be danger- ous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving engine parts. Removing rings, watches and ties is advisable.

. Jump starting is dangerous if it done incorrectly. If you are un- sure about the proper procedure for jump starting, consult a com- petent mechanic.

When your vehicle does not start due to a run down (discharged) battery, the vehicle may be jump started by connecting your battery to another battery (called the booster battery) with jumper cables.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

& How to jump start 1. Make sure the booster battery is 12
volts and the negative terminal is grounded. 2. the booster battery is in another vehicle, do not let the two vehicles touch. 3. Turn off all unnecessary lights and accessories. 4. Connect the jumper cables exactly in the sequence illustrated.

If

Black plate (331,1)

In case of emergency 9-11

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

9-12 In case of emergency

Black plate (332,1)

(1) Connect one jumper cable to the positive (+) terminal on the discharged battery. (2) Connect the other end of the cable to the positive (+) the booster battery. (3) Connect one end of the other jumper cable to the negative (−) terminal of the booster battery. (4) Connect the other end of the cable to the strut mounting nut.

terminal of

Make sure that the cables are not near any moving parts and that the cable clamps are not in contact with any other metal. 5. Start the engine of the vehicle with the booster battery and run it at moderate speed. Then start the engine of the vehicle that has the discharged battery. 6. When finished, carefully disconnect the cables in exactly the reverse order.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Engine overheating

WARNING

Never attempt to remove the radia- tor cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously.

If the engine overheats, safely pull off the road and stop the vehicle in a safe place.

& If steam is coming from the

engine compartment

Turn off the engine and get everyone away from the vehicle until it cools down.

& If no steam is coming from

the engine compartment

NOTE For details about how to check the coolant level or how to add coolant, refer to “Engine coolant” F11-14. 1. Keep the engine running at speed.

idling

2. Open the hood to ventilate the engine to “Engine hood” compartment. Refer F11-5. Confirm that the cooling fan is turning. If the fan is not turning, immediately turn off the engine and contact your SUBARU dealer for repair. 3. After the engine coolant temperature has dropped, turn off the engine. If any of the following conditions occur, turn off the engine.

. The temperature gauge stays in the overheated zone (if equipped). Refer to “Temperature gauge (models with type A combination meter)” F3-11. . The coolant temperature high warn- ing light remains illuminated (if equipped). Refer to “Coolant tempera- ture low indicator light/Coolant tem- perature high warning light” F3-16.

4. After the engine has fully cooled down, check the coolant level in the reservoir. is below the “LOW” If the coolant level mark, add coolant up to the “FULL” mark. 5. If there is no coolant in the reservoir, add coolant to the reservoir. Then remove the radiator cap (non-turbo models) or the coolant filler tank cap (turbo models) and fill the radiator with coolant.

If you have to remove a hot radiator cap/ coolant filler tank cap, first wrap a thick

Black plate (333,1)

In case of emergency 9-13

cloth around the cap, then turn the cap counterclockwise slowly without pressing down until it stops. Release the pressure from the cooling system. After the pres- sure has been fully released, remove the cap by pressing it down and turning counterclockwise.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

9-14 In case of emergency

Towing

If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following procedures for safety.

WARNING

Never tow AWD models (both AT and MT) with either front or rear wheels off the ground. This will cause the vehicle to spin away due to the operation or deterioration of the center differential.

Black plate (334,1)

& Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow).

Front towing hook: 1. Take the towing hook out of the tool bucket and take the screwdriver out of the tool bag. Take the wheel nut wrench out of the cargo area.

WARNING

. Do not use the towing hook except when towing your vehicle. . Be sure to remove the towing hook after towing. In particular, leaving the front towing hook mounted on the vehicle could interfere with proper operation of the SRS airbag system in a frontal collision.

CAUTION

. Use only the specified towing hook and tie-down hook. Never use suspension parts or other parts of the body for towing or tie-down purposes.

. To prevent deformation to the front bumper and the towing hook, do not apply excessive lateral load to the towing hook.

2. Pry off the cover on the front bumper using a flat-head screwdriver, and you will find a threaded hole for attaching the towing hook.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 27

the vehicle and stow it in the tool bucket. Fit the towing hook cover on the bumper.

Rear towing hook:

CAUTION

If a trailer hitch is installed, it is not possible to install the rear towing hook. To install the rear towing hook, the standard bumper beam must be installed on the vehicle at a SUBARU dealer. Consult a SUBARU dealer for details. Use a hitch ball and follow the instructions below when towing. . The weight of the object being towed must be less than the weight of the vehicle.

. Drive the vehicle 20 mph (32

km/h) or less speed.

. Do not drive more than 31 miles

(50 km).

1. Take the towing hook out of the tool bucket and take the screwdriver out of the tool bag. Take the wheel nut wrench out of the cargo area.

3. Screw the towing hook into the thread hole until its thread can no longer be seen.

4. Tighten the towing hook securely using a wheel nut wrench.

After towing, remove the towing hook from

Black plate (335,1)

In case of emergency 9-15

2. Pry off the cover on the rear bumper using a flat-head screwdriver, and you will find a threaded hole for attaching the towing hook.

3. Screw the towing hook into the thread hole until its thread can no longer be seen. – CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (336,1)

9-16 In case of emergency

Front tie-down hooks:

Rear tie-down hooks:

4. Tighten the towing hook securely using a wheel nut wrench.

After towing, remove the towing hook from the vehicle and stow it in the tool bucket. Fit the towing hook cover on the bumper.

tie-down hooks are located The front between each of the front tires and the front bumper.

The rear tie-down hooks are located near each of the jack-up reinforcements.

WARNING

Use the rear tie-down hooks only for downward anchoring. they are used to anchor the vehicle in any other direction, cables may slip off the hooks, possibly causing a dan- gerous situation.

If

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

& Using a flat-bed truck

CAUTION

WARNING

Black plate (337,1)

In case of emergency 9-17

“1st”

the select

for manual

This is the best way to transport your vehicle. Use the following procedures to ensure safe transportation. into the “P” 1. Shift lever position for automatic transmission mod- els or transmission models. 2. Pull up the parking brake lever firmly. 3. Secure the vehicle onto the carrier properly with safety chains. Each safety chain should be equally tightened and care must be taken not to pull the chains so tightly that the suspension bottoms out.

If your vehicle has a front under- spoiler and rear underspoiler (if equipped), be careful not to scrape them when placing the vehicle on the carrier and when removing the vehicle from the carrier.

& Towing with all wheels on the

ground

1. Release the parking brake and put the transmission in neutral. 2. The ignition switch should be in the “Acc” position while the vehicle is being towed. 3. Take up slack in the towline slowly to prevent damage to the vehicle.

. Never turn the ignition switch to the “LOCK” position while the vehicle is being towed because the steering wheel and the direc- tion of the wheels will be locked. . Remember that the brake booster and power steering do not func- tion when the engine is not running. Because the engine is turned off, take greater effort to operate the brake pedal and steering wheel.

it will

CAUTION

. If

transmission failure occurs, transport your vehicle on a flat- bed truck.

. Do not run the engine while being towed using this method. Trans- mission damage could result if the vehicle is towed with the engine running.

. For models with automatic trans- mission, the traveling speed must be limited to less than 20
mph (30 km/h) and the traveling distance to less than 31 miles (50
km). For greater speeds and – CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (338,1)

9-18 In case of emergency

distances, transport your vehicle on a flat-bed truck.

Rear gate – if the rear gate cannot be opened

In the event that you cannot open the rear gate by operating the power door locking switches or the remote keyless entry system, you can open it from inside the cargo area.

CAUTION

Never operate the rear gate lock release lever with fingers because doing so may cause an injury. Al- ways use a screwdriver or a similar tool.

1. Remove the access cover at bottom-center of the rear gate trim. 2. Locate the rear gate lock release lever behind the rear gate trim panel.

the

3. Slide the lever to the right using a screwdriver to unlock the rear gate. 4. Open the rear gate from outside by holding the rear gate with your hands.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Moonroof – if the moonroof cannot be closed

If the moonroof cannot be closed with the moonroof switch, you can close the moon- roof manually.

1. Remove the plug on the roof trim of the cargo area by inserting the end of the flat- head screwdriver between the roof and plug and prying it off.

Black plate (339,1)

In case of emergency 9-19

Insert a hex-head wrench in the end of

2. the motor shaft. To close the moonroof, turn the wrench counterclockwise. Have your vehicle checked and repaired by an authorized SUBARU dealer.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Black plate (2,1)

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —

Left Page

Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22

Black plate (19,1)

Appearance care

Exterior care ....................................................... 10-2
Washing............................................................. 10-2
Waxing and polishing ......................................... 10-3
Cleaning aluminum wheels ................................. 10-3
Corrosion protection.......................................... 10-4
Most common causes of corrosion ..................... 10-4
To help prevent corrosion................................... 10-4

Cleaning the interior.......................................... Seat fabric......................................................... Leather seat materials........................................ Synthetic leather upholstery............................... Climate control panel, audio panel, instrument

panel, console panel, and switches .................. Monitor (if equipped).......................................... Cargo tray (if equipped) .....................................

10-5
10-5
10-5
10-5

10-5
10-6
10-6

10

北米Model "A8170BE-A" EDITED: 2011/ 6/ 6

10-2 Appearance care

Exterior care & Washing

CAUTION

. When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.

. Do not wash the engine compart- ment and area adjacent to it. If water enters the engine air in- take, electrical parts or the power steering fluid reservoir, it will cause engine trouble or a mal- function of power steering.

. Do not use organic solvents when washing the surface of the bulb assembly cover. If a deter- gent with organic solvents is mistakenly used to wash the surface, completely rinse off the detergent with water. Otherwise, the surface may be damaged.

. Since your vehicle is equipped with a rear wiper, automatic car- wash brushes could become tangled around it, damaging the

wiper arm and other compo- nents. Ask the automatic car- wash operator not the brushes touch the wiper arm or to fix the wiper arm on the rear window glass with adhesive tape before operating the machine.

to let

NOTE When having your vehicle washed in an automatic car wash, make sure beforehand that the car wash is of suitable type. The best way to preserve your vehicle’s beauty is frequent washing. Wash the vehicle at least once a month to avoid contamination by road grime.

Wash dirt off with a wet sponge and plenty of lukewarm or cold water. Do not wash the vehicle with hot water and in direct sunlight.

insects,

tar, soot,

Salt, chemicals, tree sap, and bird droppings should be washed off by using a light detergent, as required. If you use a light detergent, make certain that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should be promptly flushed from the surface and not allowed to dry there. Rinse the vehicle thoroughly

Black plate (342,1)

with plenty of lukewarm water. Wipe the remaining water off with a chamois or soft cloth. ! Washing the underbody Chemicals, salts and gravel used for deicing road surfaces are extremely cor- rosive, accelerating the corrosion of un- derbody components, such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders, and sus- pension. Thoroughly flush the underbody and in- side of the fenders with lukewarm or cold water at frequent intervals to reduce the harmful effects of such agents.

Mud and sand adhering to the underbody components may accelerate their corro- sion. After driving off-road or on muddy or sandy roads, wash the mud and sand off the underbody. Carefully flush the suspen- sion and axle parts, as they are particu- larly prone to mud and sand buildup. Do not use a sharp-edged tool to remove caked mud.

CAUTION

. Be careful not to damage brake hoses, sensor harnesses, and other parts when washing sus-

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

pension components.

. Be careful not to flush the engine bottom for a long time. It may cause damage of some electrical parts.

! Using a warm water washer . Keep a good distance of 12 in (30 cm) or more between the washer nozzle and the vehicle. . Do not wash the same area continu- ously. . If a stain will not come out easily, wash by hand. Some warm water washers are of the high temperature, high pressure type, and they can damage or deform the resin parts such as moldings, or cause water to leak into the vehicle. & Waxing and polishing Always wash and dry the vehicle before waxing and polishing. Use a good quality polish and wax and apply them according to the manufac- turer’s instructions. Wax or polish when the painted surface is cool.

Be sure to polish and wax the chrome trim, as well as the painted surfaces. Loss of wax on a painted surface leads to loss of the original luster and also quickens the deterioration of the surface. It is recom-

mended that a coat of wax be applied at least once a month, or whenever the surface no longer repels water.

If the appearance of the paint has dimin- ished to the point where the luster or tone cannot be restored, lightly polish the surface with a fine-grained compound. Never polish just the affected area, but include the surrounding area as well. Always polish in only one direction. A No. 2000 grain compound is recom- mended. Never use a coarse-grained compound. Coarse-grained compounds with a smaller grain-size number could damage the paint. After polishing with a compound, coat with wax to restore the original luster. Frequent polishing with a compound or an incorrect polishing tech- nique will result in removing the paint layer and exposing the undercoat. When in doubt, it is always best to contact your SUBARU dealer or an auto paint specia- list.

CAUTION

Do not use any agents with organic solvents on the surface of the bulb assembly cover. If a polish or wax with organic solvents is mistakenly applied to the cover surface, com- pletely wipe off the polish or wax.

Black plate (343,1)

Appearance care 10-3

Otherwise, the cover surface may be damaged.

NOTE Be careful not to block the windshield washer nozzles with wax when waxing the vehicle.

& Cleaning aluminum wheels . Promptly wipe the aluminum wheels clean of any kind of grime or agent. If dirt is left on too long, it may be difficult to clean off. . Do not use soap containing grit to clean the wheels. Be sure to use a neutral cleaning agent, and later rinse thoroughly with water. Do not clean the wheels with a stiff brush or expose them to a high-speed washing device. . Clean the vehicle (including the alumi- num wheels) with water as soon as possible when it has been splashed with sea water, exposed to sea breezes, or driven on roads treated with salt or other agents.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

10

10-4 Appearance care

Corrosion protection

Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable operation.

& Most common causes of

corrosion

The most common causes of corrosion are: 1. The accumulation of moisture retain- ing dirt and debris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor accidents.

Corrosion is accelerated on the vehicle when: 1. is exposed to road salt or dust It control chemicals, or used in coastal areas where there is more salt in the air, or in areas where there is considerable industrial pollution. 2. It is driven in areas of high humidity, especially when temperatures range just above freezing. 3. Dampness in certain parts of the vehicle remains for a long time, even

though other parts of the vehicle may be dry. 4. High temperatures will cause corro- sion to parts of the vehicle which cannot dry quickly due to lack of proper ventila- tion.

& To help prevent corrosion Wash the vehicle regularly to prevent corrosion of the body and suspension components. Also, wash the vehicle promptly after driving on any of the following surfaces. . Roads that have been salted to prevent them from freezing in winter . Mud, sand, or gravel . Coastal roads

After the winter has ended, it is recom- mended that the underbody be given a very thorough washing.

Before the beginning of winter, check the condition of underbody components, such as the exhaust system, fuel and brake lines, brake cables, suspension, steering system, floor pan, and fenders. If any of them are found to be rusted, they should be given an appropriate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need

Black plate (344,1)

assistance.

Repair chips and scratches in the paint as soon as you find them.

Check the interior of the vehicle for water and dirt accumulation under the floor mats because that could cause corrosion. Occasionally check under the mats to make sure the area is dry. Keep your garage dry. Do not park your vehicle in a damp, poorly ventilated garage. In such a garage, corrosion can be caused by dampness. If you wash the vehicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause dampness.

If your vehicle is operated in cold weather and/or in areas where road salts and other corrosive materials are used, the door hinges and locks, and hood latch should be inspected and lubricated periodically.

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

Cleaning the interior

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. (Do not use organic solvents.)

& Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft brush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thoroughly. If the fabric is still dirty, wipe using a solution of mild soap and luke- warm water then dry thoroughly.

the stain does not come out,

try a If commercially available fabric cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric adversely. Use the cleaner according to its instruc- tions. NOTE When cleaning the seat, do not use benzine, paint thinner, or any similar materials.

& Leather seat materials The leather used by SUBARU is a high quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear prematurely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove difficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage. Minor surface blemishes or bald patches may be treated with a commercial leather spray lacquer. You will discover that each leather seat section will develop soft folds or wrinkles, which is characteristic of genuine leather.

Black plate (345,1)

Appearance care 10-5

& Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and water, after first vacuum- ing or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe off with a clean, damp cloth. Commercial foam-type cleaners suitable for synthetic leather materials may be used when necessary. NOTE Strong cleaning agents such as sol- vents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials.

& Climate control panel, audio

panel, instrument panel, console panel, and switches Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. NOTE Do not use organic solvents such as paint thinners or gasoline, or strong cleaning agents that contain those solvents.

– CONTINUED –

北米Model "A8170BE-A" EDITED: 2011/ 6/ 24

10

Black plate (346,1)

10-6 Appearance care

If

& Monitor (if equipped) To clean the audio/navigation monitor, wipe it with a silicone cloth or with a soft cloth. the monitor is extremely dirty, clean it with a soft cloth moistened with neutral detergent then carefully wipe off any remaining detergent. NOTE . Do not spray neutral detergent di- rectly onto the monitor. Doing so could damage the monitor’s components. . Do not wipe the monitor with a hard cloth. Doing so could scratch the monitor. . Do not use cleaning fluid that con- tains thinner, gasoline, or any other volatile substance. Such cleaning fluid could erase the lettering on the switches at the bottom of the monitor.

& Cargo tray (if equipped) The cargo tray is provided to protect the cargo area carpet. This cargo tray is removable to facilitate easy clean up.

Clean with a cloth when necessary using mild soap and water. It is important that the bottom of the liner is dry before placing it back in the cargo area, as mildew may result.

Do not install the cargo tray if the cargo area carpet is damp or wet, as mildew may result. Dry the carpet completely before the cargo tray is installed.

Upon installation after prolonged storage, you may notice that