2011 Subaru Forester Owners Manual

vice / iPod®

WARNING

Do not operate an iPod® while driving; it may distract your atten- tion from driving and can lead to an accident.

CAUTION

. If the data stored in an iPod® is deleted while it is connected to the in-vehicle system, the data cannot be recovered.

. Do not store an iPod® in the vehicle. If an iPod® is left in the vehicle for a long period of time, it may be deformed, discolored or damaged by high temperature.

button is pressed.

NOTE . Even if a USB storage device or iPod® is connected, it cannot be played unless the . A movie cannot be played while an iPod® is connected. . While an iPod® is connected, the iPod® cannot be operated using the click wheel on the iPod® (except some models). . When using an iPod® by connecting it to in-vehicle equipment, the order of the list items displayed on the in- vehicle equipment may be different from that on the iPod®. However, this does not indicate a malfunction. . An iPod® battery that is connected to in-vehicle equipment will be charged when the ignition switch is in the “ON” or “Acc” position. However, activation of the iPod® may be delayed if the battery charge of the iPod® is low. . If an iPod® does not activate after operation, disconnect the connection cable from the iPod® and reset it. For the resetting procedure, see the User’s

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

Type C audio:

Guide that comes with the iPod®. . If an iPod® and the connection cable are connected improperly, the iPod® cannot be powered on or will not be recognized by in-vehicle equipment. In this case, disconnect the connection cable from the iPod®, and then connect it again.

*: Only when a Media Hub is connected. Type D audio:

When the USB/iPod® mode is selected, the player will start playback of the USB storage device/iPod®.

NOTE . Depending on the number of files stored in an iPod® and the firmware the iPod® may not activate version, smoothly after operation or not work properly. . Do not disconnect the connector from an iPod® during iPod® operation.

The USB connector center console. Use the connector connect a USB storage device/iPod®.

is located in the to

& How to play back 1. Connect a USB storage device/iPod®. 2. Press the button. Each time you briefly press the button, the mode changes in the following sequence.

Black plate (219,1)

Audio 5-35

& To select a track/index from

its beginning

Select a track/index in the same way that a track is selected when a CD is played. For details, refer to “To select a track from its beginning” F5-25.

& To select a chapter from its beginning when connecting iPod®

While podcasts or audiobooks are playing, select a chapter in the same way that a track is selected when a CD is played. For details, refer to “To select a track from its beginning” F5-25.

& Fast-forwarding and fast-re-

versing

Fast forward or reverse is operated in the same way a CD is played. For details, refer to “Fast-forwarding and fast-rever- sing” F5-25. NOTE When connecting iPod®: . When the end of an index is reached while fast forwarding, fast forwarding ends and play begins from the begin- ning of the next index. . When the beginning of an index is reached while rewinding, rewinding – CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-36 Audio

ends and play begins from the begin- ning of the index.

& Repeating ! When connecting USB storage de-

vice

Repeating is operated in the same way a CD is played. For details, refer to “Re- peating” F5-26. ! When connecting iPod®

Type C audio

Type D audio

Each time you briefly press the “RPT” button, the mode changes in the following sequence. Type C audio:

Type D audio:

NOTE . The “ALL RPT” indication refers to the repeat playback of all indexes in the entire iPod®. . The “SONG RPT” (type C audio)/ “ONE RPT” (type D audio) indication refers to the repeat playback of a single index. is playing. . When an audiobook is playing, the mode does not change even if you press the “RPT” button.

It repeats the index that

& Random playback

Type C audio

Type D audio

To playback a track/index/file(s) at ran- dom, press the “RDM” button for 0.5
second or longer (type C audio)/briefly (type D audio) while the track/index/file is playing.

Each time you press the button, the mode changes in the following sequence.

Black plate (220,1)

When connecting USB storage device (type C audio):

When connecting USB storage device (type D audio):

When connecting iPod® (type C audio):

When connecting iPod® (type D audio):

NOTE . The “FOLDER RDM” indication re- fers to the random playback in the folders. It randomly repeats all of the tracks in the folder. . The “ALL RDM” indication refers to the random playback in the entire USB storage device. It randomly repeats all of the tracks in the USB storage device.

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

. The “ALBUM RDM” indication refers to the shuffle playback of the album. It sequentially plays back all of the indexes in the album. . The “SONG RDM” indication refers to the shuffle playback in the entire iPod®. It randomly repeats all of the indexes in the iPod®. . When an iPod® is connected, the files are played back at random by the shuffle function of the iPod®. There- fore, iPod® operation may be different depending on the model of the con- nected iPod®. . When an audiobook or a podcast is playing, the mode does not change even if you press the “RDM” button for 0.5 second or longer (type C audio)/ briefly (type D audio). the random playback mode, To cancel press the “RDM” button for more than 0.5
second (type C audio)/briefly (type D audio) and select CANCEL. The “RDM” indication will turn off, and the normal playback mode will resume.

& SCAN (only when connecting

USB storage device)

Scan is operated in the same way a CD is played. For details, refer to “Scan (type A, B and C audio)” F5-27.

NOTE When an iPod® is connected, you cannot select the SCAN mode.

& Selecting category (only when connecting iPod®)

button is pressed for less the iPod® menu is

When the than 1.5 seconds, displayed. Each time you turn the “TUNE/TRACK/ CH” dial clockwise, the displayed category changes in the following sequence. Each time you turn the dial counterclockwise, the displayed category changes in the opposite sequence.

To select the category, press the dial. To close the iPod® menu, press the button for more than 1.5 seconds. To return to the previous screen, briefly press the

button.

Black plate (221,1)

Audio 5-37

& Display selection Refer to “Display selection (type A, B and C audio)” F5-28. ! Page scroll Refer to “Page (track/folder title) scroll” F5-28.

& Folder selection (only when connecting USB storage de- vice)

Refer to “Folder selection” F5-28. NOTE When an iPod® is connected, you cannot select a folder.

& Setting the playing speed

(only when the audiobook is playing) (type D audio)

Each time you briefly press (the “RPT” button) while the audiobook is playing, the playing speed changes in the following sequence.

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

! When “NO USB” is displayed (type

D audio)

the

This message is displayed under following conditions. . No USB storage devices/iPod® are connected. . A non-connectable USB storage de- vice/iPod® is connected.

Connect a connectable USB storage device/iPod®. ! When “No song” is displayed (type

D audio)

This message is displayed when no playable audio files are in the connected USB storage device/iPod®. Connect a USB storage device/iPod® that has play- able audio files stored in it.

5-38 Audio

& When the following mes-

sages are displayed

If one of the following messages is displayed while connecting the USB sto- rage device/iPod®, determine the cause based on the following information. If you cannot clear those messages, please contact your SUBARU dealer. ! When “CHECK DEVICE” is dis-

played

the

This message is displayed under following conditions. . When there is a short in the USB bus . When a non-corresponding device (for example a USB mouse) is connected . When a non-corresponding iPod® is connected . When a connected iPod® is frozen . When a transmission malfunction oc- curs . When an iPod® confirmation malfunc- tion occurs . When a HUB class USB storage device is connected

Disconnect the USB storage device/iPod® and check it.

Black plate (222,1)

Audio control buttons (if equipped)

These buttons are located on the spokes of the steering wheel. They allow the driver to control audio functions without taking his/her hands off the steering wheel.

& MODE button

Models without Hands-free system

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

Black plate (223,1)

Type C and D audio:

& “ ” and “ ” buttons

Audio 5-39

Models with Hands-free system

The “MODE” button is used to select the desired audio mode. Each time it is pressed, the mode changes to the next one in the following sequence: Type A and B audio:

*1: The frequency last received in the selected waveband will be displayed. *2: Only when a CD is in the player. *3: Only when the device is connected. ! Models with Hands-free system Press this button for more than 1.5
seconds if you wish to immediately cut the volume to zero. The audio display will show “MUTE”. If you press the button for more than 1.5
seconds again, the original sound volume will return and “MUTE” turns off.

Models without Hands-free system

Models with Hands-free system

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-40 Audio

“

” button or “

” button or

! With radio mode selected Press the “ ” button briefly. The radio will seek the next preset station and stop on it. Press the “ ” button continuously. The radio will seek the next receivable station and stop on it. That station’s frequency will be shown on the audio display. ! With CD mode selected Press the “ ” button to skip forward in the track/file order. Press the “ ” button to skip backward in the track/file order. The track/file number will be shown on the audio display.

When the MP3/WMA/AAC format track is playing, press the “ ” button continuously to select the next folder. Press the “ ” button continuously to go back to the previous folder. ! With USB/iPod® mode selected Press the “ ” button to skip forward in the track/file order. Press the “ ” button to skip backward in the track/file order. The track/file number will be shown on the audio display. ! With SAT mode selected Press the “ channel order. Press the “

” button to skip forward in the ” button to

Black plate (224,1)

skip backward in the channel order. The channel will be shown on the audio display.

& Volume control buttons

Models without Hands-free system

Models with Hands-free system

Press the “+” button to increase the volume. Press the “−” button to reduce the volume. A number indicating the volume will be shown on the audio display.

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

& MUTE button (models with-

out Hands-free system)

Bluetooth® audio (type C and D audio)

” button if you wish to

Press the “ immediately cut the volume to zero. The audio display will show “MUTE”. If you press the button again, the original return and “MUTE” sound volume will turns off.

This function enables you to play back audio sources from Bluetooth® audio devices. You need to register the Blue- tooth® audio device in the system before using it.

& Media format Bluetooth® audio devices cannot be connected if they are not compatible with the following Bluetooth® profiles. . A2DP (Advanced Audio Distribution Profile) . AVRCP (Audio/Video Remote Control Profile)

& Setting Bluetooth® audio 1. Select “BT-A SETUP” by pressing the “MENU” button (type C audio)/Select “BT Audio Setup” by operating the “TUNE/ TRACK/CH” dial (type D audio). 2. Perform the following procedure by operating the “TUNE/TRACK/CH” dial while “BT-A” (type C audio)/“BT Audio” (type D audio) is displayed.

Black plate (225,1)

Audio 5-41

the “PAIR AUDIO”

NOTE You cannot set a Bluetooth® audio while driving. ! Registering (pairing) device 1. Select (type C audio)/“Pair Audio Player” (type D audio) menu. If a device is already registered, “MEMORY FULL” is displayed and the mode changes to the Bluetooth® audio setting mode. 2. After the passkey is shown on the display, the passkey into the cell phone. If you input the correct passkey, “PAIRED” is displayed and the registering procedure is finished. If you input an incorrect passkey, “FAILED” is displayed, the registering procedure was not suc- cessful and the mode changes to the Bluetooth® audio setting mode.

input

NOTE After the ignition switch is turned to the “LOCK” position, the registered device is not automatically connected to the system even if the ignition switch is turned to the “Acc” or “ON” position. ! Selecting device 1. Select the “SELECT AUDIO” (type C audio)/“Select Audio Player” (type D

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-42 Audio

audio) menu. If no devices are registered, “EMPTY” is displayed and the mode changes to the Bluetooth® audio setting mode. the 2. Select device is connected, is displayed and the selecting procedure is finished. the device cannot be con- nected, “FAILED” is displayed and the selecting procedure was not successful.

If “SELECTED”

the “CONFIRM” menu.

If

the “SET PASSKEY” menu. the currently set passkey is dis-

! Setting passkey 1. Select After played, a new passkey can be entered. 2. the “TUNE/TRACK/CH” dial. 3. Select the “CONFIRM” menu. The new passkey is displayed, the passkey is changed and the mode changes to the Bluetooth® audio setting mode.

Input the new passkey by operating

! Deleting device 1. Select the “DELETE AUDIO” (type C audio)/“Delete Audio Player” (type D audio) menu. If no devices are registered, “EMPTY” is displayed and the mode changes to the Bluetooth® audio setting mode. 2. Select LETED”

the “CONFIRM” menu. “DE- is displayed and the mode

changes to the Bluetooth® audio setting mode.

(type C audio)/“BT Audio”

button and select the “BT- (type D

& Bluetooth® audio operation NOTE Depending on the connected device, it may not activate as per the following items or not work smoothly. ! How to play back Press the A” audio) mode. ! To select a track from its beginning Select a track in the same way that a track is selected when a CD is played. Refer to “To select a track from its beginning” F5- 25. ! Repeating Repeating is operated in the same way a CD is played. Refer to “Repeating” F5-26. Each time you briefly press the button (the button (type C audio)/ “RPT” button) (type D audio), the mode changes in the following sequence.

Black plate (226,1)

! Random playback Random playback is operated in the same way a CD is played. Refer to “Random playback” F5-26. Each time you press the button for 0.5 second or longer (type button (the “RDM” button) C audio)/ briefly (type D audio), the mode changes in the following sequence.

! Display selection (type C audio) Select an item to be displayed using the same method as when a CD is played. Refer to “Display selection (type A, B and C audio)” F5-28. Each time you briefly press the the indication changes in the following sequence.

button,

! Folder selection Select a folder in the same way a folder is selected when a CD is played. Refer to “Folder selection” F5-28.

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

Hands-free system (if equipped)

NOTE . For models with the genuine SUBARU navigation system, refer to the Owner’s Manual supplement for the navigation system. . When selling your vehicle, make sure that you initialize the Hands-free system to prevent personal data from being improperly accessed. The Hands-free system operates while the ignition switch is in the “Acc” or “ON” position.

& Tips for the Hands-free sys-

tem

! Bluetooth®

NOTE The Bluetooth word mark and logo are registered trademarks of Bluetooth SIG, Inc. It is possible to connect a cell phone to the in-vehicle equipment through the Blue- tooth® format (wireless) to make a phone call from the in-vehicle equipment or take an incoming phone call. Since the Bluetooth® format is wireless, a connection between the in-vehicle equip- ment and the cell phone can be made without placing them in close proximity of each other. The cell phone can be used

Black plate (227,1)

Audio 5-43

with it left in the breast pocket or bag. NOTE . The Hands-free system may not operate properly under the following conditions.

in the

– The cell phone is turned off. – The cell phone is not phone call area. – The battery of the cell phone has run down. – The cell phone is not connected to the Hands-free system. – The cell phone is behind the seat or in the glove box. – A metal material covers or touches the cell phone.

. Depending on the type of cell phone that is used, the screen on the cell phone may remain illuminated while the ignition switch is in the “ON” position. If this occurs, turn the illumi- nation off by adjusting the cell phone settings. . Depending on the setting of the cell phone, the dial lock function may be activated after making a call. Deacti- vate the automatic dial lock function of the cell phone before using the Hands- free system. . Depending on the type of cell phone that is used, operation and the sound – CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-44 Audio

volume may be different from those of cell phones currently used. . When the ignition switch is turned to the “LOCK” position during a call, the call may be disconnected or continued on the cell phone depending on the type of cell phone that is used. Note that operation of the cell phone may be necessary if the call is continued on the cell phone. . Do not speak at the same time as the other party during a call. If you and the party speak at the same time, it may be difficult for the other party to hear your voice and vice versa. This is normal. . The receiver sound volume should be set as low as possible. Otherwise, the party you are calling may notice an undesirable echo sound. . Speak clearly and loudly. . Your voice may be difficult to be heard by the party under the following conditions.

– Driving on a rough road. – Driving at a high speed. – Driving with a window open. – When air from the ventilator blows directly towards the micro- phone. – When the sound coming from the ventilator is loud.

– When the cell phone is too close to the microphone.

. The sound quality may degrade due to the influence of the cell phone that is connected to the system or the circum- stances of the Bluetooth network. . When another Bluetooth® device is simultaneously connected, noise may be heard in the voice coming from the hands-free phone. ! Corresponding profiles for the cell

phone

. HFP (Hands Free Profile): Ver. 1.0
. OPP (Object Push Profile): Ver. 1.1

& Certification for the Hands-

free system

CAUTION

FCC WARNING Changes or modifications not ex- pressly approved by the party re- sponsible for compliance could void the user’s authority to operate the equipment.

NOTE This device complies with Part 15 of the FCC Rules and RSS-Gen of IC

Black plate (228,1)

Rules. Operation is subject to the following two conditions: (1) this de- vice may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.

it

if

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful interference in a residential installation. This equipment interference to may cause harmful radio communications, is not installed and used in accordance with the instructions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful inter- ference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the inter- ference by one or more of the following measures. . Reorient or relocate the receiving antenna. . Increase the separation between the

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

the dealer or an experi-

equipment and receiver. . Connect the equipment into an out- let on a circuit different from that to which the receiver is connected. . Consult enced radio/TV technician for help. . Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment. . This equipment complies with FCC/ IC radiation exposure limits set forth for an uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply with- out maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated keeping the radiator at least 20 cm or more away from person’s body (ex- cluding extremities: hands, wrists, feet and ankles). . This transmitter must not be co- located or operated in conjunction with any other antenna or transmitter.

& Safety precautions

WARNING

. For safety reasons, avoid operat- ing the cell phone while driving. . Do not make a phone call while driving. When you have an in- coming call, stop the vehicle in a safe location before taking the incoming phone call. When you have to absolutely take a phone call, tell the caller “I’ll call you back”. And then call the caller back after stopping the vehicle in a safe location.

CAUTION

. Do not leave the cell phone in the vehicle. The temperature in the vehicle may become extremely high and cause a malfunction of the cell phone.

. When using the cell phone, be careful not to get it close to the in-vehicle equipment. Getting it too close to the in-vehicle equip- ment may result in deterioration in tone quality or a poor connect- ing condition.

Black plate (229,1)

Audio 5-45

. In the frequency band used by this equipment, along with indus- trial, scientific and medical equipment such as a microwave oven, radio stations (a license is required) to be used by the production line in the factory to identify movable bodies, specific small power radio stations (a license is not required) and ama- teur radio stations (a license is required) are being operated. (These three types of radio sta- tions are hereinafter referred to as “other radio stations.”) Before using this equipment, be sure to check to see if “other radio stations” are being operated in the vicinity. If there is detrimental radio interference from this equipment to “other radio sta- tions,” move the equipment to another location as soon as possible to avoid radio interfer- ence. The frequency band used by this equipment is in the 2.4
GHz zone. The FH-SS modulation is employed as a modulation method. The expected inflicting interference distance is less than 10 m (33 ft). This equipment uses a full band and can avoid a band

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

Black plate (230,1)

! Menu list of the Hands-free system Turn the “TUNE/TRACK/CH” dial to select a menu, and then press the dial to enter the selected menu.

system. Perform the following procedure to register a cell phone. 1. Press the OFF hook switch “ENGLISH”/“FRANÇAIS” by 2. Select operating the “TUNE/TRACK/CH” dial. Then “WELCOME!” will be displayed. 3. Press the “TUNE/TRACK/CH” dial or the talk switch 4. Select the “RECORD NAME” menu. 5. Say the name to be registered. the “CONFIRM” menu. After 6. Select “CAR M_MEDIA” is displayed, a pass key is displayed. Input the displayed pass key into the 7. cell phone while “PKY: ****” (type C audio)/“PASS KEY: ****” (type D audio) is displayed. If you input the correct pass key, is displayed and the registration procedure is finished. If you input an incorrect pass key, “FAILED” is displayed and the registration procedure was not successful.

“PAIRED”

NOTE When the ignition switch is turned to the “Acc” or “ON” position, the regis- tered cell phones are automatically connected to the system.

5-46 Audio

used by a movable body identifi- cation device.

& Using the Hands-free system ! Turning on/off the Hands-free mode

1) OFF hook switch 2) ON hook switch 3)

Talk switch

To turn on the Hands-free mode, press the OFF hook switch the Hands-free mode, press the ON hook switch ! Preparation for using the Hands-

. To turn off

free system

Before using the Hands-free system, it is necessary to register a cell phone in the

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

Black plate (231,1)

Audio 5-47

First menu

Second menu

Third menu

Details

Page

PHONE BOOK* ADD ENTRY

BY VOICE

BY PHONE

Adding a new number by voice

Adding a new number by cell phone

MANUAL INPUT

Adding a new number by inputting manually

CALL HISTORY

Adding a new number from the call history

GO BACK

LIST NAMES

CHANGE NAME

SET SPD DIAL/SET SPEED DIAL

DELETE ENTRY

DEL SPD DIAL/DE- LETE SPEED DIAL

GO BACK

DIAL

STORE

DELETE

GO BACK

REDIAL

CALLBACK

DIAL

STORE

DELETE

GO BACK

—

—

—

—

—

—

—

—

—

—

—

—

—

—

Showing the list of the names registered in the phonebook

Changing a name registered in the phonebook

Registering a speed dial

Deleting phonebook data

Deleting a registered speed dial

Redialing

Adding a new number stored in the outgoing call history memory

Deleting a number stored in the outgoing call history memory

5-52

Dialing a number stored in the incoming call history memory

5-53

Adding a new number stored in the incoming call history memory

5-51

Deleting a number stored in the incoming call history memory 5-52

5-50

5-50

5-50

5-51

5-51

5-52

5-52

5-52

5-52

5-53

5-51

*: If a cell phone is not registered, the menu described in the chart is not indicated.

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

Black plate (232,1)

5-48 Audio

First menu

Second menu

Third menu

Details

Page

SETUP

SECURITY

SET PIN

PHBK LOCK*/ PHONE BOOK LOCK*

PHBK UNLOCK*/ PHONE BOOK UN- LOCK*

GO BACK

Setting a PIN code

Locking the phonebook

Unlocking the phonebook

PHONE SETUP

PAIR PHONE

Registering a new cell phone

SELECT PHONE

Selecting a cell phone to be used

CHANGE NAME

Changing the registered name of the cell phone

LIST PHONES

Showing the list of the registered cell phones

SET PASSKEY

Changing the pass key

DELETE

GO BACK

Deleting the registered cell phone

SYSTEM SETUP

GUIDANCE VOL/ GUICANCE VOLUME Setting the volume of the voice guidance INITIALIZE

Initialization

SEL LANGUAGE/SE- LECT LANGUAGE

GO BACK

—

GO BACK

Selecting the language (using the Hands-free system)

*: If a PIN code is not registered, the menu described in the chart is not available.

5-54

5-54

5-54

5-46

5-54

5-54

5-55

5-55

5-55

5-55

5-55

5-55

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

! Voice command system

1) OFF hook switch 2) ON hook switch 3)

Talk switch

To turn on the voice command system, press the talk switch briefly. To turn off the voice command system, wait for 5
seconds without using the voice command system.

The commands available for the voice command system are listed in the follow- ing chart.

Command

English

Français

10

11

12

13

14

15

16

17

18

19

0 (zero, oh)

1 (one)

2 (two)

3 (three)

4 (four)

5 (five)

6 (six)

7 (seven)

8 (eight)

9 (nine)

* (star)

# (pound)

+ (plus)

callback

redial

dial by number

0 (zéro)

1 (un)

2 (deux)

3 (trois)

4 (quatre)

5 (cinq)

6 (six)

7 (sept)

8 (huit)

9 (neuf)

* (étoile)

# (carré, dièse)

+ (plus)

rappel

recomposer

composer par nu- méro

dial by name

composer par nom

phonebook

setup

registre

réglages

20

21

22

23

24

25

26

27

28

29

30

32

33

34

35

36

37

Black plate (233,1)

Audio 5-49

phone book add entry

ajouter l’entrée dans le registre

phone book change name

phone book delete entry

phone book list names

phone book set speed dial

phone book delete speed dial

modifier le nom dans le registre supprimer l’entrée du registre

lister les noms du registre

configurer compo- sition abrégée pour le registre

supprimer compo- sition abrégée pour le registre

phone book unlock déverrouiller le re-

gistre

31 mute

cancel

help

repeat

go back

dial

previous

delete

store

confirm

annuler

aide

répéter

retourner

sourdine

composer

précédent

supprimer

enregistrer

confirmer

phone setup

réglages du télé- phone

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-50 Audio

Black plate (234,1)

security

sécurité

pair phone

jumeler le télé- phone

change name

modifier le nom

38

39

40

41

select phone

42

list phones

43

44

45

46

47

48

49

50

51

52

53

54

55

set pass key

add entry

delete entry

delete speed dial

by voice

by phone

call history

set speed dial

incoming

outgoing

list names

set PIN

phone book lock

sélectionner le tél- éphone

lister les télé- phones

configurer le passe-partout ajouter l’entrée supprimer l’entrée supprimer compo- sition abrégée

vocalement

par téléphone historique d’appels configurer compo- sition abrégée

entrant

sortant

lister les noms

configurer NIP verrouiller le regis- tre

! Updating phonebook data NOTE The maximum number of phonebook entries that can be registered in the phonebook is 50. ! Registering by voice 1. Select the “BY VOICE” menu. 2. Press the talk switch 3. Say the phone number to be regis- tered. 4. Select the “CONFIRM” menu. 5. Select the “RECORD NAME” menu by operating the “TUNE/TRACK/CH” dial or press the talk switch 6. Say the name (voice tag) registered. the “CONFIRM” menu. Then 7. Select “STORED” is displayed and the mode changes to the registering speed dial mode. Refer to “Registering speed dial” F5-51.

to be

! Registering by phone 1. Select the “BY PHONE” menu. 2. Select “TRANSFER” is displayed. 3. Transfer the data from the cell phone. For details about transferring the data, refer to the Owner’s Manual of the cell

the “CONFIRM” menu. Then

phone. 4. Select the “RECORD NAME” menu by operating the “TUNE/TRACK/CH” dial or press the talk switch 5. Say the name (voice tag) registered. the “CONFIRM” menu. Then 6. Select “STORED” is displayed and the mode changes to the registering speed dial mode. Refer to “Registering speed dial” F5-51.

to be

Input the phone number to be regis-

! Registering by inputting manually 1. Select the “MANUAL INPUT” menu by operating the “TUNE/TRACK/CH” dial. 2. tered. 3. Select the “RECORD NAME” menu by operating the “TUNE/TRACK/CH” dial or press the talk switch 4. Say the name (voice tag) registered. the “CONFIRM” menu. Then 5. Select “STORED” is displayed and the mode changes to the registering speed dial mode. Refer to “Registering speed dial” F5-51.

to be

NOTE While inputting the phone numbers, if

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

“GO BACK” (type C audio)/“BS” (type D audio) is chosen using the “TUNE/ TRACK/CH” dial, the character that was input last is deleted. ! Registering from call history 1. Select the “CALL HISTORY” menu. 2. Select “OUTGOING” or “INCOMING” by operating the “TUNE/TRACK/CH” dial. 3. Select the phone number by operating the “TUNE/TRACK/CH” dial. 4. Select the “RECORD NAME” menu by operating the “TUNE/TRACK/CH” dial or press the talk switch 5. Say the name (voice tag) registered. the “CONFIRM” menu. Then 6. Select “STORED” is displayed and the mode changes to the registering speed dial mode. Refer to “Registering speed dial” F5-51.

to be

! Registering from redial 1. Select the “REDIAL” menu. 2. Select the phone number by operating the “TUNE/TRACK/CH” dial. 3. Select the “STORE” menu. 4. Select the “CONFIRM” menu. 5. Select the “RECORD NAME” menu by operating the “TUNE/TRACK/CH” dial or press the talk switch

to be

6. Say the name (voice tag) registered. the “CONFIRM” menu. Then 7. Select “STORED” is displayed and the mode changes to the registering speed dial mode. Refer to “Registering speed dial” F5-51.

! Registering from call back 1. Select the “CALL BACK” menu. 2. Select the phone number by operating the “TUNE/TRACK/CH” dial. 3. Select the “STORE” menu. 4. Select the “CONFIRM” menu. 5. Select the “RECORD NAME” menu by operating the “TUNE/TRACK/CH” dial or press the talk switch 6. Say the name (voice tag) registered. the “CONFIRM” menu. Then 7. Select “STORED” is displayed and the mode changes to the registering speed dial mode. Refer to “Registering speed dial” F5-51.

to be

! Registering speed dial 1. After registering phonebook data, se- lect the “SPEED DIAL” menu. 2. Press the preset button (from

to ) in which you want to register the

Black plate (235,1)

Audio 5-51

phone number.

NOTE If the number to be used is already registered in speed dial, “OVER- WRITE?” will be displayed. ! List names function The voice tags registered in the phone- book are spoken by using the list names function. To use the list names function, perform the following procedure. 1. Select the “LIST NAMES” menu. 2. Choose the registered data by press- ing the talk switch or by operating the “TUNE/TRACK/CH” dial. Then “SE- LECTED” is displayed. You can choose the following menus. . “DIAL” to make a phone call . “CHANGE NAME” to change the name (voice tag) . “SET SPD DIAL”/“SET SPEED DIAL” to set the speed dial . “DELETE ENTRY” to delete the name (voice tag) from the phonebook . “GO BACK” to go back to the menu mode NOTE . After “LIST NAMES” is selected, if

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-52 Audio

is pushed, the

the OFF hook switch selected number is called. . After “LIST NAMES” is selected, if no operation is performed, the mem- ories are displayed and voice tags are spoken. After all memories/voice tags are displayed/spoken, “END OF LIST” is displayed and the mode changes to the “PHONE BOOK” menu mode. ! Changing voice tag 1. Select the “CHANGE NAME” menu. 2. Select the phone number by operating the “TUNE/TRACK/CH” dial/by pressing the talk switch and saying the voice tag. the “CONFIRM” menu (only 3. Select after saying the voice tag). Then the selected phone number/name is dis- played. 4. Press the talk switch 5. Say the new voice tag. 6. Select “CHANGED” is displayed.

the “CONFIRM” menu. Then

the “SET SPD DIAL”/“SET

! Set speed dial 1. Select SPEED DIAL” menu. 2. Select the phone number by operating the “TUNE/TRACK/CH” dial/by pressing the talk switch and saying the voice

tag. 3. Select after saying the voice tag). 4. Press the preset button (from

the “CONFIRM” menu (only

to ) in which you want to register the

phone number.

! Deleting the phonebook data 1. Select the “DELETE ENTRY” menu. 2. Select the phone number by perform- ing either of the following procedures.

– Operate the “TUNE/TRACK/CH” dial – Press the talk switch the voice tag

and say

the “CONFIRM” menu. Then 3. Select “DELETED” is displayed and the selected phonebook data is deleted.

! Deleting the speed dial 1. Select the “DEL SPD DIAL”/“DELETE SPEED DIAL” menu. 2. Press the preset button (from

to to delete the

) in which you want

speed dial. the “CONFIRM” menu. Then 3. Select “DELETED” is displayed and the selected speed dial is deleted.

Black plate (236,1)

! Deleting the redial data 1. Select the “REDIAL” menu. 2. Select the phone number by operating the “TUNE/TRACK/CH” dial. 3. Select the “DELETE” menu. the “CONFIRM” menu. Then 4. Select “DELETED” is displayed and the selected redial data is deleted.

! Deleting the callback data 1. Select the “CALLBACK” menu. 2. Select the phone number by operating the “TUNE/TRACK/CH” dial. 3. Select the “DELETE” menu. the “CONFIRM” menu. Then 4. Select “DELETED” is displayed and the selected callback data is deleted.

! Making a phone call ! Making a phone call by saying name 1. Select the top menu (phone menu). 2. Press the talk switch 3. Say “DIAL BY NAME”. 4. Press the talk switch 5. Say the desired name (voice tag) to be called. 6. Select the “DIAL” menu.

again.

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

! Making a phone call by saying

number

1. Select the top menu (phone menu). 2. Press the talk switch 3. Say “DIAL BY NUMBER”. 4. Press the talk switch 5. Say the desired phone number to be called. 6. Select the “DIAL” menu.

again.

! Making a phone call from speed dial It is possible to select a phone number from speed dial registered with the in- vehicle equipment to make a phone call. 1. Select the top menu (phone menu). 2. Press the preset button (from

to ) in which the desired number is

registered. 3. Press the OFF hook switch

NOTE When a preset button for which num- bers are not registered is pressed, an error message is indicated on the audio screen. ! Redial 1. Select the “REDIAL” menu. 2. Press the OFF hook switch

Black plate (237,1)

Audio 5-53

! Taking a phone call and declining

an incoming call

To take a phone call: Press the OFF hook switch To put an incoming call on hold: Press the ON hook switch To decline an incoming call: Press the ON hook switch for more than 1.5
seconds. ! Volume control

briefly.

3. Select the desired number by turning the “TUNE/TRACK/CH” dial. 4. Perform either of the following proce- dures.

– Press the OFF hook switch – Press the “TUNE/TRACK/CH” dial, then select the “DIAL” menu.

! Callback 1. Select the “CALL BACK” menu. 2. Press the OFF hook switch 3. Select the desired number by turning the “TUNE/TRACK/CH” dial. 4. Perform either of the following proce- dures.

– Press the OFF hook switch – Press the “TUNE/TRACK/CH” dial, then select the “DIAL” menu.

! Making a phone call from list name It is possible to select a phone number from the list name registered with the in- vehicle equipment to make a phone call. For details, refer to “List names function” F5-51. ! Top redial 1. Select the top menu (phone menu). 2. Press the OFF hook switch load the outgoing call history. 3. Select the “DIAL” menu.

and

You can adjust the phone call volume, the voice volume and the voice guidance volume. Refer to “Volume control buttons” F5-40.

– CONTINUED –

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-54 Audio

! Adjustable level of each volume

Volume

Phone call

Voice

Voice guidance

Range

0 to 14

0 to 14

0 to 6

Initial setting

the “SET PIN” menu. Then

& Bluetooth® setting ! Security setting ! Setting PIN code The PIN code is a 4-digit number and is used when locking the phonebook. 1. Select “CURRENT PIN?” is displayed. 2. Input the current PIN code by operat- ing the “TUNE/TRACK/CH” dial or saying the number. 3. Select the “CONFIRM” menu. 4. Input the new PIN code by operating the “TUNE/TRACK/CH” dial or saying the number. 5. Select the “CONFIRM” menu.

! Locking the phonebook the “PHBK LOCK”/“PHONE- 1. Select BOOK LOCK” menu. Then “CURRENT PIN?” is displayed. 2.

Input the PIN code by operating the

“TUNE/TRACK/CH” dial or saying the number. 3. Select the inputted PIN code is correct, “LOCKED” is displayed and the phonebook is locked.

the “CONFIRM” menu.

If

NOTE While the phonebook is locked, if the operation restricted menu is selected, “PHBK LOCK” is displayed. ! Unlocking the phonebook 1. Select the “PHBK UNLOCK”/“PHONE- BOOK UNLOCK” menu. Then “CUR- RENT PIN?” is displayed. NOTE If the phonebook is not locked, “UN- LOCK” is displayed and the mode changes to the security mode. 2. Input the PIN code by operating the “TUNE/TRACK/CH” dial or saying the number. the “CONFIRM” menu. If the 3. Select “UN- inputted PIN code is correct, LOCKED” is displayed and the phone- book is unlocked.

Black plate (238,1)

! Phone setup ! Setting pair phone Refer to “Preparation for using the Hands- free system” F5-46. ! Selecting phone To select the registered cell phone for connecting to the in-vehicle equipment, perform the following procedure. 1. Select the “SELECT PHONE” menu. If no cell phones are registered, “EMPTY” is displayed and the mode changes to the “PHONE SETUP” mode. 2. Select the cell phone by operating the “TUNE/TRACK/CH” dial or saying the voice tag. the “CONFIRM” menu (only 3. Select after saying the voice tag). “SELECTED” is displayed, the selected cell phone is connected to the in-vehicle equipment and the mode changes to the “PHONE SET- UP” mode.

! Changing the voice tag of the cell

phone

1. Select the “CHANGE NAME” menu. If no cell phones are registered, “EMPTY” is displayed and the mode changes to the “PHONE SETUP” mode. 2. Select the cell phone by operating the “TUNE/TRACK/CH” dial or saying the

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

voice tag. 3. Register the voice tag. For details, refer to “Preparation for using the Hands- free system” F5-46.

is turned,

! List phones function The cell phone voice tags saved in the cell phone list are spoken by using the list phones function. 1. Select the “LIST PHONES” menu. If no cell phones are registered, “EMPTY” is displayed and the mode changes to the “PHONE SETUP” mode. 2. Registered cell phones are displayed on the saved side. While displayed, if the “TUNE/TRACK/CH” dial the next registered cell phone is displayed. Press the ON hook button to close the Hands-free menu. 3. Select a cell phone by operating the “TUNE/TRACK/CH” dial or pressing the talk switch is displayed. 4. Select the following menus. . “SELECT PHONE” selected cell phone . “CHANGE NAME” to change the voice tag . “DELETE” to delete the selected cell phone from the list

. Then “SELECTED”

to connect

the

. “GO BACK” to go back to the “PHONE SETUP” mode

the “SET PASSKEY” menu. the currently set passkey is dis-

! Setting passkey 1. Select After played, a new passkey can be entered. 2. Input the new passkey by operating the “TUNE/TRACK/CH” dial or saying the passkey. 3. Select the “CONFIRM” menu. The new passkey is displayed, the passkey is changed and the mode changes to the “PHONE SETUP” mode.

! Deleting registered cell phone from

the list

1. Select the “PHONE SETUP” menu. 2. Select the “DELETE” menu. 3. Select a cell phone to be deleted by operating the “TUNE/TRACK/CH” dial or saying a voice tag. “DE- 4. Select LETED” is displayed, the data is deleted and the mode changes to the “PHONE SETUP” mode.

the “CONFIRM” menu.

! System setup You can select the following menus only by operating the “TUNE/TRACK/CH” dial.

Black plate (239,1)

Audio 5-55

! Setting guidance volume To set the guidance volume, perform the following procedure. 1. Select DANCE VOLUME” menu. 2. Set the guidance volume by operating the “TUNE/TRACK/CH” dial.

the “GUIDANCE VOL”/“GUI-

! Initializing the registered data To initialize the registered data, perform the following procedure. 1. Select the “INITIALIZE” menu. the “CONFIRM” menu. First 2. Select “PLEASE WAIT”, then “INITIALIZED” is displayed. The registered data is initia- lized and the mode changes to the last mode.

the language, perform the

! Selecting language To select following procedure. 1. Select LECT LANGUAGE” menu. 2. Select the desired language by oper- ating the “TUNE/TRACK/CH” dial.

the “SEL LANGUAGE”/“SE-

北米Model "A8160BE-B" EDITED: 2010/ 10/ 14

5-56 Audio

Screensaver (type D audio)

If the following operations are not per- formed for more than 30 seconds while the audio is ON, the screensaver will be displayed. . Operate any button or dial . Shift the shift lever/select lever to the “R” position . A cell phone registered in the Hands- free system is called

If one of the following operations is performed, the screensaver turns off and the operation screen will be displayed.