To turn off the VDC system, push the VDC OFF switch. The Push the VDC OFF switch again or restart the engine to turn on the system. (See “Vehicle Dynamic Control (VDC) system” in the “5. Starting and driving” section.)
indicator will illuminate.
Instrument panel
Center console (if so equipped)
SIC3493
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (111,1)
The power outlet is located in the instrument panel and the center console (if so equipped).
CAUTION
The outlet and plug may be hot during or immediately after use.
. Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. . Use power outlet with the engine running to avoid discharging the vehicle battery.
. Avoid using power outlet when the air conditioner, headlights or rear window defroster is on.
This power outlet is not designed for use with a cigarette lighter unit. . Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tem- perature fuse may open.
. Before inserting or disconnecting a plug, be sure the electrical acces- sory being used is turned OFF.
Instruments and controls 2-41
. When not in use, be sure to close the cap. Do not allow water to contact the outlet.
Black plate (112,1)
STORAGES
S35-D-110201-CF7976D3-F285-4050-AFD1-1371CF792F0B
CUP HOLDERS
S35-D-110201-FD1D8479-5AEA-4CA7-8486-247F76618FF5
CAUTION
. Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.
. Use only soft cups in the cup holder. Hard objects can injure you in an accident.
SIC3494
Front
The flap *A will be folded down when inserting a large container. To remove the inner tray for cleaning, pull it up as illustrated *1 .
2-42 Instruments and controls
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (113,1)
. Do not leave glasses in the sun- glasses holder while parking in direct sunlight. The heat may da- mage the glasses.
To open the cup holder, pull the lid.
Rear
SUNGLASSES HOLDER
S35-D-110201-7D49A2AA-DD28-4615-B72E-A1CBFE395B60
SIC3495
SIC3496
WARNING
Keep the sunglasses holder closed while driving to prevent an accident.
To open the sunglasses holder, push *1 .
CAUTION
. Do not use for anything other than
glasses.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Instruments and controls 2-43
Black plate (114,1)
GLOVE BOX
S35-D-110201-F9260F73-5260-4688-8D88-814B9E5BA4ED
WARNING
Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop.
To open the glove box, pull the handle. To close, push the lid in until the lock latches. The glove box light illuminates when the head- light switch is turned on. *A Card holder *B Back side pocket of lid *C Removable partition (if so equipped) To remove the partition, pull it out.
SIC3497
SIC3498
SIC3499
CONSOLE BOX S35-D-110201-E018BA87-9079-45DE-909F-A77EB11D068E To open the console boxes, push up the knob *A and pull up the lid. To close, push the lid down until latched. To remove the inner box (if so equipped) for cleaning or storing a large object, pull it up as illustrated *B . The inside of the console box lid is designed to be used as a card holder *C and pen holders *D .
2-44 Instruments and controls
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (115,1)
LUGGAGE FLOOR BOX (if so equipped) S35-D-110201-B2DC4A4F-CB14-4C93-B757-CA7BE5833E8C Type A: To open the luggage floor box, push *A . To close, push the lid until the lock latches. The net partitions can be folded to make a larger storage space.
CAUTION
To avoid damage, do not load more than 22 lbs (10 kg) of cargo into the luggage floor box.
Type B: To open the luggage floor box, pull the handle *B on the lid. To close, push the lid until the lock latches. The luggage floor box needs to be removed when you need a spare tire. (See “Flat tire” in the “6. In case of emergency” section.)
Type A
SIC4530
LUGGAGE SIDE BOX
S35-D-110201-65867C13-C89A-46EC-8E2A-F8212C01D932
To open the luggage side box, pull up the strap.
SIC4267
Type B
SIC3514
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Instruments and controls 2-45
Black plate (116,1)
cover is not removed, it may da- mage the top tether strap during a collision. Your child could be ser- iously injured or killed in a collision if the child restraint top tether strap is damaged.
. Do not allow cargo to contact the top tether strap when it is attached to the top tether anchor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or that contacts the top tether strap may damage the top tether strap during a collision. Your child could be seriously injured or killed in a colli- sion if the child restraint top tether strap is damaged.
hooks and hold until it is retracted. To remove the cargo cover, stow the cover and pull the holder to the opposite side *2 .
WARNING
. Never put anything on the cargo cover, no matter how small. Any object on it could cause an injury in an accident or sudden stop.
. Close the cargo cover when folding
the rear seat.
. Do not leave the cargo cover in the vehicle with it disengaged from the holder.
. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unse- cured cargo could cause personal injury.
If the cargo cover contacts the top tether strap when it is attached to the top tether anchor, remove the cargo cover from the vehicle or secure it on the cargo floor below its attachment location. If the cargo
[ Edit: 2011/ 6/ 22 Model: S35-D ]
SIC3503
CARGO COVER (if so equipped) S35-D-110201-4D798BFB-9ED7-4FB8-9F2C-7D3C067EF3DC The cargo cover keeps the contents in the cargo area hidden from the outside. To use the cargo cover, pull it out and hang both sides on the hooks *1 . To stow the cargo cover, remove it from the
2-46 Instruments and controls
. Unsecured luggage can become dangerous in an accident or sudden stop.
CAUTION
Do not apply a total load of more than 22 lb (10 kg) *A or 7 lb (3 kg) *B to a single hook.
Black plate (117,1)
SIC4550
COAT HOOKS (if so equipped) S35-D-110201-DF957E51-D7CE-457F-B5FE-B60CF761743A The coat hooks are equipped above the rear window.
CAUTION
Do not apply a total load of more than 2
lb (1 kg) to a single hook.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Instruments and controls 2-47
LUGGAGE HOOKS (if so equipped)
S35-D-110201-2D988198-3E52-49E3-8EEB-85813B616CF7
SIC3504
WARNING
. Always make sure that the luggage is properly secured. Use the suitable ropes and hooks.
Black plate (118,1)
WARNING
. Drive extra carefully when the vehi- cle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack.
. Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sud- den or unusual handling maneuvers. . Roof rack load should be evenly
distributed.
. Do not exceed maximum roof rack
load weight capacity.
. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.
CAUTION
Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof
SIC3506
SIC3549
UTILITY HOOK To use the utility hook on the seatback, pull it.
S35-D-110201-0F642A2D-5628-4E33-83E0-2E6B14382F28
CAUTION
. Do not apply a total load of more
than 6 lb (3 kg) to the hook.
. Do not use the utility hook to pull the seatback to the upright and locked position. Doing so will cause the utility hook to break.
2-48 Instruments and controls
ROOF RACK (if so equipped)
GUID-963DC233-F1BF-4195-80FA-612BBCFAEFB2
Secure the crossbars to the roof rail before
loading. The crossbars are available from a
NISSAN dealer.
Always distribute the luggage evenly on the roof
rack. Do not load more than 99 lb (45 kg). Be
careful that your vehicle does not exceed the
Gross Vehicle Weight Rating (GVWR) or its
Gross Axle Weight Rating (GAWR front and
rear). The GVWR and GAWR are located on the
F.M.V.S.S. or C.V.M.S.S. certification label (lo-
cated on the driver’s door pillar). For more
information regarding GVWR and GAWR, see
“Vehicle loading information” in the “9. Technical
and consumer information” section.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
rack from the ground, use a ladder or stool.
Black plate (119,1)
WINDOWS
S35-D-110201-EF5A4CAB-3CE8-402A-B85B-F12E85049006
POWER WINDOWS
S35-D-110201-28870A1D-95F8-487F-8BEF-004065E33A6E
WARNING
. Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the win- dow lock switch to prevent unex- pected use of the power windows.
. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols and become trapped in the window. Unattended children could become involved in serious acci- dents.
The power windows operate when the ignition
switch is in the ON position, or for about 45
seconds after the ignition switch is turned to the
OFF position. If the driver’s or front passenger’s
door is opened during this period of about 45
seconds, power to the windows is canceled.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
SIC3507
1. Window lock button 2. Driver side window 3. Rear left passenger side window 4. Front passenger side window 5. Rear right passenger side window Main power window switch (driver’s side) To open or close the window, push down *A or pull up *B the switch and hold it. The main switch (driver side switches) will open or close all the windows.
GUID-B6E7617E-E40E-40C3-9E55-437ACDA41B5A
Instruments and controls 2-49
Black plate (120,1)
GUID-21155F19-5215-4B78-A2CE-1C399D86BA17
Locking passengers’ windows When the lock button *C is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.
SIC3508
SIC3509
Passenger side power window switch GUID-6392E6CE-0551-411A-994B-8AC9D946BB5E The passenger side switch will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it.
GUID-E7474ECC-09DE-4A54-A358-7896B84E25A1
the
Automatic operation (if so equipped) The automatic operation is available for switch that has an mark on its surface. Type A: To fully open or close the window, push down or pull up the switch to the second detent and release it; the switch need not be held. The window will automatically open or close all the way. To stop the window, just push or lift the switch in the opposite direction. Type B: To fully open the window, push down the switch to the second detent and release it; the switch need not be held. The window will automatically open all the way. To stop the just lift the switch. To fully close the window,
2-50 Instruments and controls
[ Edit: 2011/ 6/ 22 Model: S35-D ]
window, push and hold the switch. A light push or pull on the switch will cause the window to open or close until the switch is released.
Auto-reverse function (if so equipped)
GUID-CD58E688-0E5F-4849-A2F9-9DCE763F2A71
WARNING
There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the window.
If the control unit detects something caught in the window as it is closing, the window will be immediately lowered. The auto reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is turned to the OFF position. Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs.
Black plate (121,1)
If the windows do not close automatically GUID-4366A858-91A3-4739-91C0-DACFB774B6DE If the power window automatic function (closing only) does not operate properly, perform the following procedure to initialize the power window system. 1. Turn the ignition switch to the ON position. 2. Close the door. 3. Open the window completely by operating
the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed completely.
5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.
If the power window automatic function does not operate properly after performing the pro- cedure above, have your vehicle checked by a NISSAN dealer.
MOONROOF (if so equipped)
GUID-74BA112D-48AA-4F68-AF07-7C0714B7A644
WARNING
In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.
. Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
CAUTION
. Remove water drops, snow, ice or sand from the moonroof before opening.
. Do not place any heavy object on the moonroof or surrounding area.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Instruments and controls 2-51
AUTOMATIC MOONROOF
GUID-795A67FE-3AA6-4D5F-A971-C344A69CEBB7
The moonroof only operates when the ignition
switch is in the ON position.
The automatic moonroof is operational for about
45 seconds, even if the ignition switch is turned
to the OFF position. If the driver’s door or the
passenger’s door is opened during this period of
about 45 seconds, power to the moonroof is
canceled.
Sunshade
S35-D-110201-6A117BAD-3314-4417-9693-3DEEE0575E80
The sunshade will open automatically when the
moonroof is opened. However, it must be closed
manually.
Black plate (122,1)
Auto reverse function
S35-D-110201-AF18E966-5C54-4980-BC51-E872555FB4DF
WARNING
There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the moonroof.
If the control unit detects something caught in the moonroof when it is closing, the moonroof will be immediately opened. The auto reverse function can be activated when the moonroof is closed by automatic operation when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is turned to the OFF position. If the moonroof cannot be closed automatically when the auto reverse function activates due to a malfunction, push and hold the switch toward
*2 .
Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.
SIC3510
Sliding the moonroof GUID-E58CB540-F94C-4392-847D-DF07AA0A152B To fully open or close the moonroof, push the switch toward *1 or *2 and release it; it need not be held. The roof will automatically open or close all the way. To stop the roof, push the switch in any direction while it is opening or closing.
Tilting the moonroof GUID-F8514024-28D3-4F20-A4B9-9C5D9274A6BB To tilt up, first close the moonroof by pushing the switch toward *2 . Push the switch toward again and release it; it need not be held. To tilt down the moonroof, push the switch toward *1 .
*2
2-52 Instruments and controls
[ Edit: 2011/ 6/ 22 Model: S35-D ]
If the moonroof does not operate
GUID-750E5F7D-B6E5-4E9E-9714-1DE514A949D8
If
the moonroof does not operate properly,
perform the following procedure to initialize the
moonroof operation system.
1.
is open, close it fully by
If the moonroof repeatedly pushing the switch toward *2 .
2. Push and hold the switch toward *2
to
tilt the moonroof up.
3. Release the moonroof switch after moonroof moves slightly up and down.
4. Push and hold the switch toward *1
the
to
fully tilt the moonroof down.
5. Check if normally.
the moonroof switch operates
If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.
INTERIOR LIGHTS
S35-D-110201-6554559D-EE81-4A45-B1ED-9C063E192D41
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
Black plate (123,1)
SIC3512
MAP LIGHTS
S35-D-110201-C243F5B9-4483-4D93-AA0B-1EA9F7CF9D9D
Push the light lens to turn the map light on or off.
The map light control switch has three positions:
ON *1 , DOOR *2 and OFF *3 .
The light *4
(if so equipped) will
when the headlight switch is turned to the
or
illuminate
position.
ON position When the switch is in the ON position *1 , the map lights will illuminate.
S35-D-110201-7683F6B1-A28E-4E34-903D-85E1BC5B2ED3
Instruments and controls 2-53
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (124,1)
S35-D-110201-55BC51B8-E593-4DF0-A4A4-C808144A2F0B
OFF position When the switch is in the OFF position *3 , the map lights will not illuminate, regardless of the condition.
SIC3513
CEILING LIGHT GUID-BE9CB642-0C31-473C-A93E-63673165372B The ceiling light switch has three positions: ON, DOOR and OFF.
ON position When the switch is in the ON position *1 , the ceiling light will illuminate.
S35-D-110201-70BCA29A-4C18-4168-8B6D-98BE0BE33E7F
S35-D-110201-96E5D9BB-55A7-44D8-B0DC-A27CDCB014C4
DOOR position When the switch is in the DOOR position *2 , the ceiling light will illuminate under the following conditions:
ignition switch is turned to the LOCK position
S35-D-110201-6D5F4D58-B171-4027-B458-15DB5CE5FB39
DOOR position When the switch is in the DOOR position *2 , the map lights will illuminate under the following conditions:
ignition switch is turned to the LOCK position — remain on for about 15 seconds. doors are unlocked by pushing the unlock button (on the keyfob or Intelligent Key) or the request switch (Intelligent Key system equipped model), with the ignition switch in the LOCK position — remain on for about 15 seconds. any door is opened and then closed with the ignition switch in the LOCK position — remain on for about 15 seconds. any door is opened with the ignition switch in the ACC or ON position — remain on while the door
is opened. When the door is closed, the lights go off.
The lights will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.
2-54 Instruments and controls
[ Edit: 2011/ 6/ 22 Model: S35-D ]
.
— remain on for about 15 seconds. doors are unlocked by pushing the unlock (on the keyfob or Intelligent Key) button or the request switch (Intelligent Key system equipped model), with the ignition switch in the LOCK position — remain on for about 15 seconds. any door is opened and then closed with the ignition switch in the LOCK position — remain on for about 15 seconds. any door is opened with the ignition switch in the ACC or ON position — remain on while the door
is opened. When the door is closed, the lights go off.
The light will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.
S35-D-110201-D2E4CC19-C6A3-43E3-A546-AEDCAD5B81E9
OFF position When the switch is in the OFF position *3 , the ceiling light will not illuminate, regardless of the condition.
Black plate (125,1)
VANITY MIRROR LIGHTS (if so equipped)
CARGO LIGHT
S35-D-110201-60256316-8D60-44BF-B844-446DA9E30D11
GUID-AC455466-F059-41D4-A466-DD80D2F1310F
SIC2064
The light on the vanity mirror will turn on when the cover on the vanity mirror is opened. When the cover is closed, the light will turn off. The lights will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.
SIC2131A When the switch is in the ON position *1 , the light illuminates while the lift gate is opened. When the lift gate is closed, the light will turn off. When the switch is in the OFF position *2 , the light will turn off. The light will turn off after 30 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Instruments and controls 2-55
HomeLink® UNIVERSAL TRANSCEIVER (if so equipped)
S35-D-110201-66C2B4FC-EF3E-4734-84F9-A3A414FE2874
HomeLink® Universal Transceiver provides a
convenient way to consolidate the functions of
up to three individual hand-held transmitters into
one built-in device.
HomeLink® Universal Transceiver:
. Will operate most Radio Frequency (RF)
devices such as garage doors, gates, home
and office lighting, entry door locks and
security systems.
Is powered by your vehicle’s battery. No
separate batteries are required.
the
vehicle’s battery is discharged or is dis-
connected, HomeLink® will retain all pro-
gramming.
If
Once HomeLink® Universal Transceiver is programmed, retain the original transmit- ter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink® Universal Transceiver buttons should be erased for security purposes. For additional information, see “Program- ming HomeLink®” later in this section.
the vehicle,
WARNING
. Do not use HomeLink® Universal Transceiver with any garage door opener that lacks safety stop and
2-56 Instruments and controls
Black plate (126,1)
PROGRAMMING HomeLink®
S35-D-110201-D5C00885-9125-4196-B013-1D365942DDA0
To program your HomeLink® Transceiver
to
operate a garage door, gate, or entry door
opener, home or office lighting, you need to be
at
the same location as the device. Note:
Garage door openers (manufactured after
1996) have “rolling code protection”. To pro-
gram a garage door opener equipped with
“rolling code protection”; you will need to use
a ladder to get up to the garage door opener
motor to be able to access the “smart or learn”
program button.
reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982.) A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.
. During programming procedure, your garage door or security gate may open or close. Make sure that people and objects are clear of the garage door, gate, etc. that you are programming.
. Your vehicle’s engine should be turned off while programming HomeLink® Universal Transceiver.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (127,1)
5.
button - releasing when the device begins to activate. If the indicator light on HomeLink® blinks rapidly for two seconds and then turns solid, HomeLink® has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train HomeLink®, completing the programming may require a ladder and another person for convenience.
If
6. Push and release the program button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. the wire originates from under a light lens, you will need to remove the lens to access the training button. NOTE: Once you have pushed and released the training button on the garage door opener’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. For convenience, use the help of a second person to assist when performing this step.
7. Quickly (within 30 seconds of pushing and releasing the garage door opener training button) and firmly push and release the
Instruments and controls 2-57
SIC3182
SIC3183
1. To begin, push and hold the 2 outer
HomeLink® buttons (to clear the memory)
until the indicator light *A blinks (after 20
seconds). Release both buttons.
2. Position the end of the hand-held transmitter 1-3 inches away from the HomeLink® sur- face.
3. Using both hands, simultaneously push and hold both the HomeLink® button you want to program and the hand-held transmitter button. DO NOT release the buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on HomeLink® flashes, changing from a “slow blink” to a “rapid blink”. This could take up to 90 seconds. When the indicator light blinks rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, push and hold the programmed HomeLink®
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (128,1)
surface. Hold the transmitter in that position for up to 15 seconds. If HomeLink® is not programmed within that time, try holding the transmitter in another position - keeping the indicator light in view at all times.
If you continue to have programming difficulties,
please contact the NISSAN Consumer Affairs
Department. The phone numbers are located in
the Foreword of this Owner’s Manual.
CLEARING THE PROGRAMMED IN-
FORMATION
S35-D-110201-27C5AE41-4F1F-4D07-8C90-BF387497020E
Individual buttons cannot be cleared, however to
clear all programming, push and hold the two
outside buttons and release when the indicator
light begins to flash (in approximately 20
seconds).
REPROGRAMMING A SINGLE
HomeLink® BUTTON
S35-D-110201-6CBBA29C-5D44-408B-8B3F-6BE900E6D619
To reprogram a HomeLink® Universal Transcei-
ver button, complete the following.
1. Push and hold the desired HomeLink®
button. Do not release the button until step
4 has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 2 to 5 in (50 to 127
mm) away from the HomeLink® surface.
HomeLink® button you’ve just programmed. Push and release the HomeLink® button up to three times to complete the training.
8. Your HomeLink® button should now be programmed. To program the remaining HomeLink® buttons for additional door or gate openers, follow steps 2 through 8 only.
NOTE:
Do not repeat step 1 unless you want to
“clear” all previously programmed
HomeLink® buttons.
If you have any questions or are having difficulty
programming your HomeLink® buttons, please
to the HomeLink® web site at: www.
refer
homelink.com or call 1-800-355-3515.
PROGRAMMING HomeLink® FOR CA-
NADIAN CUSTOMERS
GUID-6ACFA63C-38E7-40AC-9D44-7085C554AF73
Prior
regulations required
hand-held transmitters to stop transmitting after
2 seconds. To program your hand-held trans-
mitter to HomeLink®, continue to push and hold
the HomeLink® button (note steps 2 through 4
under “Programming HomeLink®”) while you
push and re-push (“cycle”) your hand-held
transmitter every 2 seconds until the indicator
light flashes rapidly (indicating successful pro-
gramming).
to 1992, D.O.C.
2-58 Instruments and controls
NOTE:
If programming a garage door opener, etc.,
it is advised to unplug the device during
the “cycling” process to prevent possible
damage to the garage door opener com-
ponents.
OPERATING THE HomeLink® UNIVER-
SAL TRANSCEIVER
S35-D-110201-2F4ADB5B-DB01-458A-B276-C4210429C7AD
HomeLink® Universal Transceiver
(once pro-
grammed) may now be used to activate the
garage door, etc. To operate, simply push the
appropriate programmed HomeLink® Universal
Transceiver button. The red indicator light will
illuminate while the signal is being transmitted.
PROGRAMMING TROUBLE-DIAGNO-
SIS
S35-D-110201-0B7FA6ED-FEC7-47F2-8980-375FA4DA8824
If HomeLink® does not quickly learn the hand-
held transmitter information:
replace the hand-held transmitter batteries with new batteries. position the hand-held transmitter with its battery area facing away from the HomeLink® surface. push and hold both the HomeLink® and hand-held transmitter buttons without inter- ruption. position the hand-held transmitter 2 to 5 in (50 to 127 mm) away from the HomeLink®
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (129,1)
device must accept any interference that may be received, including interference that may cause undesired operation.
The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.
DOC: ISTC 1763K1313
FCC I.D.: CB2V67690
3. Push and hold the hand-held transmitter
button.
4. The HomeLink® indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The HomeLink® Universal Transceiver button
has now been reprogrammed. The new device
can be activated by pushing the HomeLink®
button that was just programmed. This proce-
dure will not affect any other programmed
HomeLink® buttons.
IF YOUR VEHICLE IS STOLEN
S35-D-110201-0E33C5C3-FB03-4FDB-B7CB-C54F97BF0844
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink®. Consult the
Owner’s Manual of each device or call
the
manufacturer or dealer of
those devices for
additional information.
When your vehicle is recovered, you will
need to reprogram the HomeLink® Univer-
sal Transceiver with your new transmitter
information.
FCC Notice:
This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Instruments and controls 2-59
Black plate (130,1)
MEMO
2-60 Instruments and controls
[ Edit: 2011/ 6/ 22 Model: S35-D ]
3 Pre-driving checks and adjustments
Black plate (131,1)
Keys ...
Doors ...
NISSAN Vehicle Immobilizer System keys ... Intelligent Keys (if so equipped)
Locking with key ... Locking with inside lock knob ... Locking with power door lock switch ... Automatic door locks ... Child safety rear door lock ...
.............................................................................................. 3-2
................... 3-2
...
..................................... 3-3
............................................................................................ 3-4
.................................................................. 3-5
.......................................... 3-5
............................ 3-5
......................................................... 3-6
............................................... 3-6
................. 3-7
..................... 3-8
............................ 3-10
..................................... 3-12
.................................... 3-12
................................................. 3-13
Intelligent Key system (if so equipped) Intelligent Key operating range ... Door locks/unlocks precaution ... Intelligent Key operation ...
Remote keyless entry system (if so equipped)
How to use remote keyless entry system ...
...
...
Fuel-filler door
Hood ... Lift gate ...
Lift gate release ...
Warning signals ... Troubleshooting guide ... How to use remote keyless entry function ...
.............................................................. 3-14
.................................................. 3-15
.............. 3-16
......................................................................................... 3-20
.................................................................................... 3-21
.............................................................. 3-22
........................................................................ 3-22
...
...
......................................... 3-22
.................................................................. 3-22
...
....................................................................... 3-24
................................................................... 3-24
................................................................................ 3-25
...................................................................................... 3-25
..................................................................... 3-25
............................................................... 3-27
..................................................................... 3-28
Inside mirror Outside mirrors ... Vanity mirror
Opening the fuel-filler door Fuel-filler cap ...
Tilt operation ...
...
...
Steering wheel
Sun visors ... Mirrors ...
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (132,1)
duplicate your existing key. As many as 5 keys can be used with one vehicle. You should bring all the registered keys that you have to a NISSAN dealer for registration. This is because the registration process will erase the memory of all key codes previously registered into the NISSAN Vehicle Immobilizer System. After the registration process, these components will only recognize keys coded into the NISSAN Vehicle Immobilizer System during registration. Any key that is not given to your dealer at the time of registration will no longer be able to start your vehicle.
CAUTION
Do not allow the NISSAN Vehicle Im- mobilizer System key, which contains an electrical transponder, to come in contact with salt water. This could cause the system to malfunction.
KEYS
S35-D-110201-DE70668C-DA04-469B-B5C4-09EB700CFDF7
A key number plate is supplied with your keys.
Record the key number and keep it in a safe
place (such as your wallet), not in the vehicle. If
you lose your keys, see a NISSAN dealer for
duplicates by using the key number. NISSAN
does not record any key numbers so it is very
important to keep track of your key number plate.
A key number is only necessary when you have
lost all keys and do not have one to duplicate
from.
If you still have a key, this key can be
duplicated by a NISSAN dealer.
SPA2405
1. Master key (2) 2. Key number plate (1) NISSAN VEHICLE IMMOBILIZER SYS- TEM KEYS S35-D-110201-9A9F7A26-2A31-4E79-9589-56D7FD9A686E Your vehicle can only be driven with the master keys which are registered to the NISSAN Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head. Never leave these keys in the vehicle. Additional or replacement keys: If you still have a key, the key number is not necessary when you need extra NISSAN Vehicle Immobilizer System keys. Your dealer can
3-2 Pre-driving checks and adjustments
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (133,1)
nents when registering new keys, be sure to take all Intelligent Keys that you have to the NISSAN dealer.
equipment and personal computers.
CAUTION
. Do not allow the Intelligent Key, which contains electrical compo- nents, to come into contact with water or salt water. This could affect the system function.
. Do not drop the Intelligent Key. . Do not strike the Intelligent Key
sharply against another object.
If the outside temperature is below 148F (-108C) degrees, the battery of the intelligent key may not function properly.
. Do not place the Intelligent Key for an extended period in an area where temperatures exceed 1408F (608C).
. Do not attach the Intelligent Key with a key holder that contains a magnet.
. Do not place the Intelligent Key near equipment that produces a mag- netic field, such as a TV, audio
SPA2406
Intelligent Key (2)
1.
2. Mechanical key (inside Intelligent Key) (2)
3. Key number plate (1)
INTELLIGENT KEYS (if so equipped)
S35-D-110201-D15F2CE6-CCCA-4C47-A594-B5FAFAF94A86
Your vehicle can only be driven with the
Intelligent Keys which are registered to your
vehicle’s Intelligent Key system components and
NISSAN Vehicle Immobilizer System compo-
nents. As many as 4 Intelligent Keys can be
registered and used with one vehicle. The new
keys must be registered by a NISSAN dealer
prior to use with the Intelligent Key system and
NISSAN Vehicle Immobilizer System of your
vehicle. Since the registration process requires
erasing all memory in the Intelligent Key compo-
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Pre-driving checks and adjustments 3-3
Black plate (134,1)
DOORS
S35-D-110201-11F4111D-00C7-425A-8CBE-258C29021D15
CAUTION
WARNING
Always carry the mechanical key in- stalled in the Intelligent Key.
. Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintentionally opening the doors, and will help keep out intruders.
. Before opening any door, always look for and avoid oncoming traffic. . Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols. Unattended children could become involved in serious acci- dents.
SPA2033
Mechanical key
S35-D-110201-9601DF7C-3FF9-40D5-B6B8-9E5EEEBD0038
To remove the mechanical key, release the lock
knob at the back of the Intelligent Key.
To install the mechanical key, firmly insert it into
the Intelligent Key until the lock knob returns to
the lock position.
Use the mechanical key to lock or unlock the
doors. (See “Doors” later in this section.)
3-4 Pre-driving checks and adjustments
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (135,1)
SPA2394
SPA1814
SPA2300
LOCKING WITH KEY
S35-D-110201-EA701736-2D62-4FE5-9A07-3E66A223B473
The power door lock system allows you to lock
or unlock all doors simultaneously.
Turning the driver’s door key cylinder to the front of the vehicle *1 will lock all doors and the lift gate. Turning the driver’s door key cylinder once to the rear of the vehicle *2 will unlock the driver’s door. After returning the key to the neutral position, turning it to the rear again within 5 seconds will unlock all doors and the lift gate.
LOCKING WITH INSIDE LOCK KNOB
S35-D-110201-F596BA5E-9604-428A-990B-ACE1BA5124FA
To lock the door without the key, move the inside
lock knob to the lock position *1
then close the
door.
To unlock, move the inside lock knob to the
unlock position *2 .
When locking the door without a key, be
sure not to leave the key inside the vehicle.
LOCKING WITH POWER DOOR LOCK SWITCH S35-D-110201-CBDF94BB-B871-4D60-9710-B678FE8875EE Operating the power door lock switch will lock or unlock all the doors. The switches are located on the driver’s and front passenger’s door armrests. To lock the doors, push the power door lock switch to the lock position *1 with the driver’s or front passenger’s door open, then close the door. When locking the door this way, be sure not to leave the key inside the vehicle. To unlock the doors, push the power door lock switch to the unlock position *2 .
Pre-driving checks and adjustments 3-5
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (136,1)
5. The ignition switch must be placed in the OFF and ON position again between each setting change.
When the automatic door unlock system is deactivated, the doors do not unlock when the ignition switch is placed in the OFF position. To unlock the door manually, use the inside lock knob or the power door lock switch (driver’s or front passenger’s side).
SPA2037
CHILD SAFETY REAR DOOR LOCK
S35-D-110201-E7140EBB-C56B-4EFA-B4A0-B356D8C49F31
Child safety rear door locks help prevent the rear
doors from being opened accidentally, espe-
cially when small children are in the vehicle.
When the levers are in the lock position
*1 , the rear doors can be opened only
from the outside.
To disengage, move the levers to the unlock
position *2 .
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Lockout protection
S35-D-110201-D9159B01-8C96-4797-ADA7-C072902F1545
When the power door lock switch (driver or front
passenger) is moved to the lock position with
the key in the ignition switch or the Intelligent
Key in the vehicle and any door open, all doors
will lock and unlock automatically.
This function helps to prevent the keys from
being accidentally locked inside the vehicle.
AUTOMATIC DOOR LOCKS
S35-D-110201-9792C716-DB41-40DC-A515-5B1BB12E9151
. All doors lock automatically when the vehicle
speed reaches 15 MPH (24 km/h).
. All doors unlock automatically when the
ignition switch is placed in the OFF position.
The automatic unlock function can be
deactivated or activated. To deactivate or
activate the automatic door unlock system,
perform the following procedure:
1. Close all doors.
2. Place the ignition switch in the ON position.
3. Within 20 seconds of performing Step 2,
push and hold the power door lock switch to
the
position (UNLOCK) for more than 5
seconds.
4. When activated,
the hazard indicator will flash twice. When deactivated, the hazard indicator will flash once.
3-6 Pre-driving checks and adjustments
Black plate (137,1)
NISSAN dealer.
If the indicator light on the keyfob does not illuminate when pushing the buttons, the keyfob battery may be discharged. For information regarding the replacement of a battery, see “Battery replacement” in the “8. Maintenance and do-it-yourself” section.
REMOTE KEYLESS ENTRY SYSTEM (if so equipped)
S35-D-110201-1E00637E-1C0B-4FEB-811E-9997F446A105
It is possible to lock/unlock all doors (including
the lift gate), and activate the panic alarm by
using the keyfob from outside the vehicle.
Before locking the doors, make sure the
key is not left in the vehicle.
The keyfob can operate at a distance of
approximately 33 ft (10 m) from the vehicle.
(The effective distance depends upon the
conditions around the vehicle.)
As many as 5 keyfobs can be used with one
vehicle. For
information concerning the pur-
chase and use of additional keyfobs, contact a
NISSAN dealer.
The keyfob will not function:
. When the keyfob is not within the opera-
tional range.
. When the doors are open or not closed
securely.
. When the key is in the ignition switch. . When the battery is discharged.
WARNING
The remote keyless entry keyfob trans- mits radio waves when the buttons are pushed. The FAA advises that the radio waves may affect aircraft navigation and communication systems. Do not
operate the keyfob while on an air- plane. Make sure the buttons are not operated unintentionally when the unit is stored during a flight.
CAUTION
The following conditions or occur- rences will damage the keyfob. . Do not allow the keyfob to become
wet.
. Do not drop the keyfob. . Do not strike the keyfob sharply
against another object.
If the outside temperature is below 148F (-108C) degrees, the battery of keyfob may not function properly.
. Do not place the keyfob for an extended period in an area where temperatures exceed 1408F (608C).
If a keyfob is lost or stolen, NISSAN recommends erasing the ID code of that keyfob. This will prevent the keyfob from unauthorized use to unlock the vehicle. For information regarding the erasing procedure, please contact a
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Pre-driving checks and adjustments 3-7
Black plate (138,1)
remains open.
5. The hazard indicator flashes twice and the
horn chirps once. . When the LOCK
button is pushed with all doors locked, the hazard indicator flashes twice and the horn chirps once as a reminder that the doors are already locked. . Operate the door handles to confirm that the
doors have been securely locked.
Using panic alarm
S35-D-110201-1BFE353E-D31D-455C-84CE-1BA2297CF9C6
If you are near your vehicle and feel threatened,
you may activate the alarm to call attention as
follows:
1. Push the PANIC
button *3
keyfob for more than 1 second.
on the
2. The theft warning alarm and headlights will
stay on for 25 seconds.
3. The panic alarm stops when:
Unlocking doors 1. Push the UNLOCK
S35-D-110201-29B39298-D051-4CAC-95C7-6FD65C0E8B70
button *2 on the
SPA2416
*1 LOCK button *2 UNLOCK button *3 PANIC button HOW TO USE REMOTE KEYLESS ENTRY SYSTEM
S35-D-110201-CA37B8F2-FD76-4255-B48E-4F80A3B5B847
S35-D-110201-6A487745-4220-4149-BAAE-6CE691473769
Locking doors 1. Remove the key from the ignition switch. 2. Close all the doors. 3. Push the LOCK
button *1
on the
keyfob.
4. All the doors will lock.
All of the doors will
lock when the LOCK button is pushed even though a door
3-8 Pre-driving checks and adjustments
keyfob. . The driver’s door unlocks. . The hazard indicator flashes once if all
doors are completely closed.
2. Push the UNLOCK
button again within
5 seconds. . All the doors and the lift gate unlock. . The hazard indicator flashes once if all
doors are completely closed.
All doors will be locked automatically unless one
of the following operations is performed within 1
minute of pushing the UNLOCK
. Any door or lift gate is opened.
The ignition switch is turned to the ON position.
button.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
It has run for 25 seconds, or
. Any of
the buttons on the keyfob is pushed. (Note: the PANIC button must be pushed for more than 1 second.)
button *1
Setting hazard indicator and horn mode
S35-D-110201-9248839D-3D23-438A-9E35-5533D7B6AFCA
This vehicle is set in hazard indicator and horn
mode when you first receive the vehicle.
In hazard indicator and horn mode, when the
LOCK
is pushed, the hazard
indicator flashes twice and the horn chirps once.
button *2
When the UNLOCK
is pushed,
the hazard indicator flashes once.
If the horn chirp is not necessary, you can switch
to hazard indicator only mode by following the
switching procedure.
In hazard indicator only mode, when the LOCK
the hazard indicator
button is
flashes twice. When the UNLOCK
button is pushed,
Black plate (139,1)
pushed, neither the hazard indicator nor the horn operates.
Mode (Pushing the
or
button)
DOOR LOCK
DOOR UNLOCK
Hazard indicator and horn mode
Hazard indicator mode
HAZARD - twice HORN - once HAZARD - twice
HAZARD - once HORN - none HAZARD - none
Switching procedure:
GUID-D73A39BF-43C8-459F-9C24-47B7F579C407
To switch the hazard indicator and horn opera-
tion, push the LOCK *1
and UNLOCK
buttons on the keyfob simultaneously
*2
for more than 2 seconds. . When the hazard indicator mode is set, the
hazard indicator flashes 3 times.
. When the hazard indicator and horn mode is set, the hazard indicator flashes once and the horn chirps once.
NOS1695
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Pre-driving checks and adjustments 3-9
INTELLIGENT KEY SYSTEM (if so equipped)
S35-D-110201-1EBA8E8A-E285-4EDF-8DC6-8282FF7F52ED
WARNING
CAUTION
. Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should con- tact the electric medical equipment manufacturer for the possible influ- ences before use.
The Intelligent Key transmits radio waves when the buttons are pushed. The FAA advises that the radio waves may affect aircraft na- vigation and communication sys- t e m s . D o n o t o p e r a t e t h e Intelligent Key while on an airplane. Make sure the buttons are not operated unintentionally when the unit is stored during a flight.
The Intelligent Key system can operate all the door locks using the remote controller function or pushing the request switch on the vehicle without taking the key out from a pocket or purse. The operating environment and/or condi- tions may affect the Intelligent Key system operation. Be sure to read the following before using the Intelligent Key system.
3-10 Pre-driving checks and adjustments
. Be sure to carry the Intelligent Key with you when operating the vehi- cle.
. Never leave the Intelligent Key in the vehicle when you leave the vehicle.
The Intelligent Key is always communicating with the vehicle as it receives radio waves. The Intelligent Key system transmits weak radio waves. Environmental conditions may interfere with the operation of the Intelligent Key system under the following operating conditions. . When operating near a location where strong radio waves are transmitted, such as a TV tower, power station and broad- casting station.
. When in possession of wireless equipment, transceiver,
such as a cellular telephone, and CB radio.
. When the Intelligent Key is in contact with or
covered by metallic materials.
. When any type of radio wave remote control
is used nearby.
. When the Intelligent Key is placed near an electric appliance such as a personal
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (140,1)
computer.
. When the vehicle is parked near a parking
meter.
If
In such cases, correct the operating conditions before using the Intelligent Key function or use the mechanical key. Although the life of the battery varies depending on the operating conditions, the battery’s life is approximately 2 years. the battery is dis- charged, replace it with a new one. Since the Intelligent Key is continuously receiv- ing radio waves, if the key is left near equipment which transmits strong radio waves, such as signals from a TV and personal computer, the battery life may become shorter. For information regarding replacement of a battery, see “Battery replacement” in the “8. Maintenance and do-it-yourself” section. As many as 4 Intelligent Keys can be registered and used with one vehicle. For information about the purchase and use of additional Intelligent Keys, contact a NISSAN dealer.
CAUTION
. Do not allow the Intelligent Key, which contains electrical compo- nents, to come into contact with
Black plate (141,1)
recommends erasing the ID code of that Intelligent Key from the vehicle. This may prevent the unauthorized use of the Intelligent Key to operate the vehicle. For information regarding the erasing procedure, contact a NISSAN deal- er. The Intelligent Key function can be disabled. For information about disabling the Intelligent Key function, contact a NISSAN dealer.
water or salt water. This could affect the system function.
. Do not drop the Intelligent Key. . Do not strike the Intelligent Key
sharply against another object.
. Do not change or modify the Intel-
ligent Key.
. Wetting may damage the Intelligent Key. If the Intelligent Key gets wet, immediately wipe until it is comple- tely dry.
If the outside temperature is below 148F (−108C) degrees, the battery of the Intelligent Key may not function properly.
. Do not place the Intelligent Key for an extended period in an area where temperatures exceed 1408F (608C).
. Do not attach the Intelligent Key with a key holder that contains a magnet.
. Do not place the Intelligent Key near equipment that produces a mag- netic field, such as a TV, audio equipment, personal computers or cellular phone.
If an Intelligent Key is lost or stolen, NISSAN
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Pre-driving checks and adjustments 3-11
Black plate (142,1)
INTELLIGENT KEY OPERATING RANGE S35-D-110201-78F9827F-C347-4841-AFF5-1DE018677F6B The Intelligent Key functions can only be used when the Intelligent Key is within the specified operating range from the request switch *1 . When the Intelligent Key battery is discharged or strong radio waves are present near the operat- ing location, the Intelligent Key system’s operat- ing range becomes narrower, and the Intelligent Key may not function properly. The operating range is within 31.50 in (80 cm) from each request switch *1 . If the Intelligent Key is too close to the door glass, handle or the request
rear bumper,
3-12 Pre-driving checks and adjustments
SPA2074
SPA2407
switches may not function. When the Intelligent Key is within the operating range, it is possible for anyone who does not carry the Intelligent Key to push the request switch to lock/unlock the doors including the lift gate.
DOOR LOCKS/UNLOCKS PRECAU-
TION
GUID-5B258DE1-6D3E-4530-A070-24F6EB804D09
. Do not push the door handle request switch
with the Intelligent Key held in your hand as
illustrated. The close distance to the door
handle will cause the Intelligent Key system
to have difficulty recognizing that the In-
telligent Key is outside the vehicle.
. After locking with the door handle request switch, verify the doors are securely locked by testing them. To prevent the Intelligent Key from being left inside the vehicle, make sure you carry the key with you and then lock the doors.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (143,1)
. Do not pull the door handle before pushing the door handle request switch. The door will be unlocked but will not open. Release the door handle once and pull it again to open the door.
SPA2408
SPA2409
INTELLIGENT KEY OPERATION
S35-D-110201-EC829859-7623-4249-A79B-75682E29C873
You can lock or unlock the doors without taking
the key out from your pocket or bag.
SPA2410
Pre-driving checks and adjustments 3-13
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (144,1)
WARNING SIGNALS
S35-D-110201-0D8A99B7-E65C-4934-A016-E4324CF1EA91
The Intelligent Key system is equipped with a
function that is designed to minimize improper
operations and to help prevent the vehicle from
being stolen. The warning buzzer sounds and
the warning display appears on the vehicle
information display when improper operations
are detected.
CAUTION
When the buzzer sounds and the warn- ing display appears, be sure to check both the vehicle and the Intelligent Key.
When you carry the Intelligent Key with you, you can lock or unlock all doors by pushing the door handle request switch (driver’s or front passen- ger’s) *A or lift gate request switch *B within the range of operation. When you lock or unlock the doors, the hazard indicator will flash and the horn (or the outside chime) will sound as a confirmation. For details, see “Setting hazard indicator and horn mode” later in this section.
Locking doors
S35-D-110201-8EA6E22F-8395-4193-8EB5-5A139EFC2C10
1. Turn the ignition switch to the LOCK
position.*1
2. Carry the Intelligent Key with you.
3. Close all the doors.*2
4. Push the door handle request switch (dri-
ver’s or front passenger’s) *A
or the lift
gate request switch *B while carrying the
Intelligent Key with you.*3
5. All the doors and the lift gate will lock. 6. The hazard indicator flashes twice and the
outside chime sounds twice.
*1: Doors will lock with the request switch while the ignition switch is in the ACC or ON position. *2: Doors will not lock with the request switch while any door is open. *3: Doors will not lock with the request switch 3-14 Pre-driving checks and adjustments
when the Intelligent Key is left inside the vehicle. However, when an Intelligent Key is inside the vehicle, doors can be locked with another registered Intelligent Key.
S35-D-110201-B5E33822-CFDC-4AA1-AD0F-54BBE3729FBB
Unlocking doors 1. Push the door handle request switch *A or the lift gate request switch *B while carrying the Intelligent Key with you.
2. The hazard indicator flashes once and out- side chime sounds once. The corresponding door or the lift gate will unlock.
3. Push the request switch again within 5
seconds.
4. The hazard indicator flashes once and out- side chime sounds once again. All the doors and the lift gate will unlock.
All doors will be locked automatically unless one
of the following operations is performed within 1
minute after pushing the request switch while
the doors are locked.
. Opening any doors.
. Pushing the ignition switch.
Inserting the mechanical key into the ignition switch.
During this 1-minute time period, if the UNLOCK button on the Intelligent Key is pushed, all doors will be locked automatically after another 1 minute.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (145,1)
TROUBLESHOOTING GUIDE
S35-D-110201-F67E3182-54C1-4F8E-8206-45B5D1438491
Symptom
Possible cause
Action to take
When pushing the request switch
The outside buzzer sounds for approximately 2
seconds.
The doors cannot be locked.
When closing the doors
The outside buzzer sounds for approximately
10 seconds.
The Intelligent Key detection warning appears
on the display and the outside buzzer sounds 3
times.
The outside buzzer sounds for approximately 3
seconds and all doors unlock.
When opening the driver’s door
A warning chime sounds continuously.
When stopping the engine
The SHIFT “P” warning appears on the display.
When turning the ignition switch A warning chime sounds continuously.
The ignition switch is not turned to the LOCK position.
The Intelligent Key has been left in the vehicle.
The ignition switch is not in the LOCK position, or the mechanical key is inserted into the ignition switch.
The selector lever is not in the P (Park) position. The ignition switch is not turned to the LOCK position.
When starting the engine
The Intelligent key battery discharge indicator appears on the display.
The battery charge is low.
Take out the Intelligent Key from the vehicle and push the request switch. Turn the ignition switch to the LOCK position and push the request switch while carrying the Intelligent Key with you. Close all the doors securely and push the request switch while carrying the Intelligent Key with you. Turn the ignition switch to the LOCK position.
Carry the Intelligent Key from the vehicle and close the door. Turn the ignition switch to the LOCK position. Remove the mechanical key from the igni- tion switch. Shift the selector lever to the P (Park) position. Turn the ignition switch to the LOCK position. Replace the battery with a new one. (See “Battery replacement” in the “8. Mainte- nance and do-it-yourself” section.)
The Intelligent Key is not in the vehicle. Carry the Intelligent Key with you.
When pushing the ignition switch
The Intelligent Key detection warning appears on the display.
The Intelligent Key is not in the vehicle. Carry the Intelligent Key.
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Pre-driving checks and adjustments 3-15
Black plate (146,1)
conditions around the vehicle.) The remote keyless entry function will not operate: . When the Intelligent Key is not within the
operational range.
. When the doors are open or not closed
securely.
. When the Intelligent Key battery is dis-
charged.
The remote keyless entry function can also operate the vehicle alarm.
HOW TO USE REMOTE KEYLESS ENTRY FUNCTION
S35-D-110201-CF29B22E-A85F-4042-83BE-F5970367F85C
WARNING
. Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should con- tact the electric medical equipment manufacturer for the possible influ- ences before use.
The Intelligent Key transmits radio waves when the buttons are pushed. The FAA advises that the radio waves may affect aircraft na- vigation and communication sys- t e m s . D o n o t o p e r a t e t h e Intelligent Key while on an airplane. Make sure the buttons are not operated unintentionally when the unit is stored during a flight.
the system function.
. Do not drop the Intelligent Key. . Do not strike the Intelligent Key
sharply against another object.
. Do not change or modify the Intel-
ligent Key.
. Wetting may damage the Intelligent Key. If the Intelligent Key gets wet, immediately wipe until it is comple- tely dry.
. Do not place the Intelligent Key for an extended period in an area where temperatures exceed 1408F (608C).
. Do not attach the Intelligent Key with a key holder that contains a magnet.
. Do not place the Intelligent Key near equipment that produces a mag- netic field, such as a TV, audio equipment, personal computers or cellular phone.
CAUTION
. Do not allow the Intelligent Key, which contains electrical compo- nents, to come into contact with water or salt water. This could affect 3-16 Pre-driving checks and adjustments
The remote keyless entry function can operate all door locks using the remote keyless entry function of the Intelligent Key. The remote keyless entry function can operate at a distance of approximately 33 ft (10 m) from the vehicle. (The operating distance depends upon the
[ Edit: 2011/ 6/ 22 Model: S35-D ]
Black plate (147,1)
. Pushing the ignition switch.
Inserting the mechanical key into the ignition switch.
During this 1-minute time period, if the UNLOCK button is pushed, all doors will be locked
automatically after another 1 minute.
Using panic alarm
S35-D-110201-F0A15784-7138-4284-8670-24D4950A9145
If you are near your vehicle and feel threatened,
you may activate the alarm to call attention as
follows:
1. Push the PANIC
button *3
on the
Intelligent Key for more than 1 second.
2. The theft warning alarm and headlights will
stay on for 25 seconds.