2011 Nissan Quest Owners Manual

The current and average fuel consumption mode shows the current and average fuel consump- tion.

Instruments and controls 2-21

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (98,1)

vehicle speed since the last reset. Resetting is switch *B for longer done by pushing the than 1 second. (The average fuel consumption is also reset at the same time.)

The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “——”.

SIC4701

Elapsed time and trip odometer (miles or km)

Elapsed time:

The elapsed time mode shows the time since the last reset. The displayed time can be reset switch *B for longer than by pushing the 1 second. (The trip odometer is also reset at the same time.)

Trip odometer:

The trip odometer mode shows the total distance the vehicle has been driven since the last reset. Resetting is done by pushing the switch *B than 1 second. elapsed time is also reset at the same time.)

longer

(The

for

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3674

Average fuel consumption (MPG, l/100
km or km/l) and speed (MPH or km/h)

Fuel consumption:

The average fuel consumption mode shows the average fuel consumption since the last reset. switch *B Resetting is done by pushing the for longer than 1 second. (The average speed is also reset at the same time.)

The display is updated every 30 seconds. At about the first 1/3 mile (500 m) after a reset, the display shows “——”.

Speed:

The average speed mode shows the average

2-22 Instruments and controls

Black plate (99,1)

pushed to the OFF position may continue to be displayed.

. When driving uphill or rounding curves, the fuel in the tank shifts, which may momenta- rily change the display.

SIC4703
Outside air temperature (ICY — 8F or 8C) The outside air temperature is displayed in 8F or 8C in the range of −22 to 1408F (−30 to 608C).

The outside air temperature mode includes a low temperature warning feature. If the outside air temperature is below 378F (38C), the warning is displayed on the screen.

The outside temperature sensor is located in front of the radiator. The sensor may be affected by road or engine heat, wind directions and other driving conditions. The display may differ from the actual outside temperature or the temperature displayed on various signs or bill- boards.

Instruments and controls 2-23

Model "E52-D" EDITED: 2010/ 10/ 25

SIC4702

Distance to empty (dte — miles or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.

The display is updated every 30 seconds.

The dte mode includes a low range warning feature. level is low, the warning is displayed on the screen.

If the fuel

level drops even lower, the dte

When the fuel display will change to “——”.

If the amount of fuel added is small, the display just before the ignition switch is

Black plate (100,1)

ALERT:

. OTHER

Alert menu can be set to notify the following items.

TIMER

Select this submenu to specify when the “TIMER” indicator activates.

Select this submenu and set or reset the distance for replacing items other than the engine oil, oil filter and tires.

To return to the top page of the setting mode, select “BACK”.

ICY

Select outside temperature warning.

this submenu to display the low

To return to the top page of the setting mode, select “BACK”.

MAINTENANCE:

The maintenance intervals of the following items can be set or reset for the reminders. . OIL

Select distance for changing the engine oil.

this submenu to set or reset

the

FILTER

Select distance for replacing the oil filter.

this submenu to set or reset

the

TIRE

OPTIONS:

The 3 option menus can be set preference.

LANGUAGE

to your

Select French or Spanish for display.

this submenu to choose English,

. UNIT

Select this submenu to choose the unit from MPG or l/100 km.

. EFFECTS

Select this menu to set scribed below to on or off.

the effects de-

— The indicator needles sweep in the meters and the ring illumination will be brightened gradually when the engine is started.

Select distance for replacing tires.

this submenu to set or reset

the

To return to the top page of the setting mode, select “BACK”.

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3678

Setting Setting cannot be made while driving. A message “Setting can only be operated when stopped” is also displayed on the dot matrix crystal display. switch *A and

switch *B are The used in the setting mode to select and decide a menu.

SKIP:

Push the warning check mode.

switch *A

to move to the

Push the

switch *B to select other menus.

2-24 Instruments and controls

Black plate (101,1)

SECURITY SYSTEMS

to move to the

SKIP:

Push the warning check mode.

switch *A

Push the

DETAIL:

switch *B to select other menus.

This item is available only when a warning is displayed.

Select this menu to see the details of warnings.

SIC3993

Warning check To see if there are any of the following warnings and corresponding details, select this menu. . No key warning

Low fuel warning

Low washer fluid warning

. Parking brake release warning . Door/lift gate open warning . Check tire pressure warning

Loose fuel cap warning

SIC4717

Your vehicle has two types of security systems, as follows: . Vehicle security system . NISSAN Vehicle Immobilizer System

The security condition will be shown by the security indicator light.

VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audio alarm signals if someone opens the doors or lift gate when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.

Instruments and controls 2-25

Model "E52-D" EDITED: 2010/ 10/ 25

The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your Intelligent Key(s) in the vehicle, and always lock it when un- attended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.

Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features.

2-26 Instruments and controls

SIC2045

How to arm the vehicle security system 1. Close all windows.

The system can be armed even if the windows are open.

2. Push the ignition switch to the OFF position.

3. Remove the Intelligent Key from the vehicle.

4. Close all doors and lift gate. Lock all doors. The doors can be locked with the Intelligent Key, door handle request switch, power door lock switch or mechanical key.

5. Confirm that

the security indicator

light comes on. The security indicator light stays on for about 30 seconds. The vehicle

Black plate (102,1)

security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is pushed to ACC or ON, the system will not arm.

Even when the driver and/or passengers are in the vehicle, the system will activate with all doors and lift gate locked with the ignition switch in the LOCK position. When pushing the ignition switch to the ACC or ON position, the system will be released.

Vehicle security system activation The vehicle security system will give the follow- ing alarm:

The headlights blink and the horn sounds intermittently.

The alarm automatically turns off after approximately 1 minute. However, the alarm reactivates if the vehicle is tampered with again.

The alarm is activated by: . Unlocking the door or opening the lift gate without using the button on the Intelligent Key, the door handle request switch or the

Model "E52-D" EDITED: 2010/ 10/ 25

mechanical key. (Even if the door is opened by releasing the door inside lock knob, the alarm will activate.)

How to stop an activated alarm The alarm will stop by unlocking a door by pushing the unlock button on the Intelligent Key, the door handle request switch or using the mechanical key. The alarm will not stop if the ignition switch is pushed to the ACC or ON position.

If the system does not operate as de- scribed above, have it checked by a NISSAN dealer.

NISSAN VEHICLE IMMOBILIZER SYS- TEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered Intelligent Key. Never leave these keys in the vehicle.

For USA:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

Black plate (103,1)

operation.

Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For Canada:

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.

SIC2045

Security indicator light The security indicator light is located on the meter panel. the NISSAN Vehicle Immobilizer System.

indicates the status of

It

The light blinks after the ignition switch is in the LOCK, ACC or OFF position. This function indicates the security systems equipped on the vehicle are operational.

If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position.

If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System

Instruments and controls 2-27

Model "E52-D" EDITED: 2010/ 10/ 25

service as soon as possible. Please bring all Intelligent Keys that you have when visiting a NISSAN dealer for service.

Black plate (104,1)

WINDSHIELD WIPER AND WASHER SWITCH

WARNING

mix the washer fluid concentrate and water.

In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

. Do not

fill

the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to

2-28 Instruments and controls

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (105,1)

REAR WINDOW WIPER AND WASHER SWITCH

WARNING

In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

the factory default setting. To turn this function on and off, see “HOW TO USE SETTING BUTTON” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.

*2 LO — continuous low speed operation *3 HI — continuous high speed operation Push the lever up *4
operation of the wiper. Pull the lever toward you *5
to operate the washer. Then the wiper will also operate several times.

(MIST) to have one sweep

. Do not

fill

the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate

Instruments and controls 2-29

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3664

The windshield wiper and washer operates when the ignition switch is in the ON position.

Push the lever down to operate the wiper at the following speed: *1

INT — intermittent operation can be ad- justed by turning the knob toward *A (Slower) or *B (Faster). When the speed sensing wiper interval function (models with center multi-function control panel) is turned on, the intermittent operation speed varies in accordance with the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed will be faster.) Note that the function is set to disabled as

Black plate (106,1)

REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH

SIC3666

SIC4718

The rear window wiper and washer operate when the ignition switch is in the ON position.

Turn the switch clockwise from the OFF position to operate the wiper. *1

Intermittent (INT) — intermittent operation (not adjustable)

tion

*2 Low (ON) — continuous low speed opera- Push the switch forward *3
to operate the washer. Then the wiper will also operate several times.

To defog/defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the switch *1 on. The indicator light *2 will come on. Push the switch again to turn the defroster off.

It will automatically turn off in approximately 15
minutes.

CAUTION

When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.

Model "E52-D" EDITED: 2010/ 10/ 25

and water.

If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper.

2-30 Instruments and controls

HEADLIGHT AND TURN SIGNAL SWITCH

XENON HEADLIGHTS (if so equipped)

WARNING

HIGH VOLTAGE

. When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.

. Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to a NISSAN dealer and have the headlights adjusted correctly.

When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.

The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn

Black plate (107,1)

off the headlights for short intervals (for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon head- lights is not reduced.

If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.

SIC3668

HEADLIGHT SWITCH Lighting *1 Turn the switch to the

position:

The front park, side marker, plate and instrument lights will come on.

tail,

license

*2 Turn the switch to the

position:

Headlights will come on and all the other lights remain on.

Instruments and controls 2-31

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (108,1)

The autolight system can turn on the headlights automatically when it is dark and turn off the headlights when it is light.

The headlights will also be turned on automa- tically at twilight or in rainy weather (when the windshield wiper is operated continuously) (if so equipped).

If the ignition switch is pushed to the OFF position and one of the doors is opened and this condition is continued, the headlights remain on for 5 minutes.

Automatic headlights off delay:

You can keep the headlights on for up to 180
seconds after you push the ignition switch to OFF and open any door then close all the doors.

the period of

the automatic You can adjust headlights off delay from 0 seconds (OFF) to 180 seconds. The factory default setting is 45
seconds.

For automatic headlights off delay setting, see “Light Off Delay” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.

SIC3669

Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically.

To set the autolight system:

1. Make sure the headlight switch is in the

AUTO position *1 .

2. Push the ignition switch to the ON position.

3. The autolight system automatically turns the

headlights on and off.

SIC4722

Be sure not to put anything on top of the photo sensor *A located on the top of the instrument panel. The photo sensor con- trols the autolight; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate.

To turn the autolight system off, turn the switch to the OFF,

position.

or

2-32 Instruments and controls

Model "E52-D" EDITED: 2010/ 10/ 25

When the headlight switch is in the position while the ignition switch is in the ON position, the lights will automatically turn off 5
minutes after the ignition switch has been pushed to the OFF position.

or

When the headlight switch remains in the or position after the lights automatically turn off, the lights will turn on when the ignition switch is pushed to the ON position.

CAUTION

. When you turn on the headlight switch again after the lights auto- matically turn off, the lights will not turn off automatically. Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, other- wise the battery will be discharged. . Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically.

SIC3670

Headlight beam select *1 To select the low beam, put the lever in the

neutral position as shown.

*2 To select the high beam, push the lever

forward while the switch is in the position. Pull it back to select the low beam. *3 Pulling the lever toward you will flash the headlight high beam even when the head- light switch is in the OFF position.

Battery saver system A chime will sound when the driver side door is or opened with the light switch in the position and the ignition switch in the ACC,

OFF or LOCK position.

Black plate (109,1)

SIC2275

Headlight aiming control (if so equipped) Depending on the number of occupants in the vehicle and the load it is carrying, the headlight axis may be higher than desired. If the vehicle is traveling on a hilly road, the headlights may directly hit the rearview mirror of the vehicle ahead or the oncoming vehicle. The light axis can be lowered with the operation of the switch.

the windshield of

The larger the number designated on the switch, the lower the axis.

When traveling with no heavy load or on a flat road, select position 0.

Instruments and controls 2-33

Model "E52-D" EDITED: 2010/ 10/ 25

WARNING

WARNING

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

Xenon headlights (if so equipped) are extremely bright compared to conven- tional headlights. If the xenon head- lights hit the rearview mirror of the vehicle ahead or the windshield of oncoming vehicle, the driver of these vehicles may have difficulty driving because of the brightness. Use the headlight aiming control switch to low- er the light axis. See “XENON HEAD- LIGHTS” earlier in this section for additional information.

Daytime running light system (Canada only) The daytime running lights automatically illumi- nate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position. Turn the position or position for full headlight switch to the illumination when driving at night.

in the

If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is pushed to the OFF position. 2-34 Instruments and controls

Black plate (110,1)

SIC3585

Instrument brightness control The instrument brightness control operates when the ignition switch is in the ON position. Pushing the control switch *A once will change the brightness to the night mode. Pushing the control switch *B once will change the brightness to the day mode.

the brightness of

To adjust instrument panel lights, push the control switches. Pushing the upper switch *A will brighten the lights. When the brightness reaches the maximum level, a beep will sound. The lower switch *B dims the lights. Repeatedly pushing the lower switch will turn the lights off and a beep will sound.

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (111,1)

HAZARD WARNING FLASHER SWITCH

SIC3671

SIC3672

SIC2574

TURN SIGNAL SWITCH *1 Turn signal Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. *2 Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flashing.

FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight position, then turn the switch switch to the position. To turn them off, turn the to the switch to the OFF position.

The headlights must be on for the fog lights to operate.

When the headlight switch is in the AUTO position (if so equipped):

Turning the fog light switch to the position will turn on the headlights, fog lights and the other lights while the ignition switch is in the ON position or the engine is running.

Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights will flash.

WARNING

If stopping for an emergency, be sure to move the vehicle well off the road.

. Do not use the hazard warning flashers while moving on the high- way unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.

Instruments and controls 2-35

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (112,1)

HORN

HEATED SEATS (if so equipped)

WARNING

Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat tempera- tures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in serious injury.

SIC3586

To sound the horn, push the pad area *A of the steering wheel.

WARNING

Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury.

CAUTION

The battery could run down if the seat heater is operated while the engine is not running.

. Do not use the seat heater for extended periods or when no one is using the seat.

. Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.

. Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

Model "E52-D" EDITED: 2010/ 10/ 25

Turn signals do not work when the hazard warning flasher lights are on.

The flasher can be actuated with the ignition switch in any position.

Some state laws may prohibit the use of the hazard warning flasher switch while driving.

MODELS WITH AUTO LIGHT SYSTEM When an impact that could activate the supple- mental air bags is detected, the hazard warning flasher lights blink automatically. If the hazard warning flasher switch is pushed, the hazard warning flashers will turn off.

WARNING

Do not turn the hazard warning flasher switch to off until you can make sure that it is safe to do so. Also, the hazard flasher warning may not blink automa- tically depending on the force of im- pact.

2-36 Instruments and controls

. Any liquid spilled on the heated seat should be removed immediately with a dry cloth.

. When cleaning the seat, never use gasoline, thinner, or any similar materials.

If any malfunctions are found or the heated seat does not operate, turn the switch off and have the system checked by a NISSAN dealer.

SIC2770

The seats are warmed by built-in heaters. The switches located on the instrument panel can be operated independently of each other.

1. Start the engine.

2. Select heat range.

*1 For high heat, push the HI (High) side of

the switch.

*2 For low heat, push the LO (Low) side of

the switch.

The indicator light in the switch *3 will illuminate when the heater is on.

Black plate (113,1)

3. To turn off the heater, return the switch to the level position. Make sure the indicator light goes off.

The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.

When the vehicle’s interior is warmed, or before you leave the vehicle, be sure to turn off the switch.

Instruments and controls 2-37

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (114,1)

BLIND SPOT WARNING (BSW) SWITCH (if so equipped)

VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH

To cancel the warning systems, push the BSW switch to turn off the system. The BSW ON indicator *1 will turn off. NOTE: If you continue to push the warning systems switch from off to on for over 4
seconds, a chime will sound. This will change the default status of the BSW system to OFF so that this system will not automatically turn on when the engine is started. If this procedure is repeated, the default status will return to ON.

SSD1179

The Blind Spot Warning (BSW) switch will turn on and off the Blind Spot Warning (BSW) system.

The BSW system will illuminate the Blind Spot Warning (BSW) indicator lights, in the outside mirrors, when the radar sensors detect a vehicle in the detection zone. is activated in the direction of the detected vehicle, a chime sounds twice and the BSW indicator light will flash. (See “BLIND SPOT WARNING (BSW) SYSTEM” in the “5. Starting and driving” section.)

the turn signal

If

The BSW switch is automatically turned on when the engine is started, and the BSW ON indicator *1 on the switch illuminates.

2-38 Instruments and controls

SSD1149

The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions.

If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off.

To turn off the VDC system, push the VDC OFF switch. The

indicator will illuminate.

Push the VDC OFF switch again or restart the engine to turn on the system. (See “VEHICLE DYNAMIC CONTROL (VDC) SYSTEM” in the “5. Starting and driving” section.)

Model "E52-D" EDITED: 2010/ 10/ 25

POWER OUTLET

CAUTION

. Use power outlet with the engine running to avoid discharging the vehicle battery.

. Avoid using power outlet when the air conditioner, headlights or rear window defroster is on.

. Before inserting or disconnecting a plug, be sure the electrical acces- sory being used is turned OFF.

. When not in use, be sure to close the cap. Do not allow water to contact the outlet.

Instrument panel

SIC4723

Black plate (115,1)

Type A

To use the power outlet, pull illustrated.

the cover as

CAUTION

The outlet and plug may be hot during or immediately after use.

. Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

This power outlet is not designed for use with a cigarette lighter unit. . Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tem- perature fuse may open.

Cargo area

SIC4724

Instruments and controls 2-39

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (116,1)

exceed a 120 volt, 150W (1.25A) power draw or the power outlet may switch off automatically. If this occurs, turn the main switch on the power outlet off and wait a short period of time before turning it back on again. If an electrical appliance with a wattage of less than 150W is used, the power outlet will be usable again.

. Use this power outlet with the (If the engine is engine running. stopped, this could result in a dis- charged battery.)

. When using the outlet for a long period of time such as when idling etc., the battery may discharge de- pending on the vehicle conditions, even if the engine is running.

. Some electrical appliances with wattages below 150W, may not operate normally. For example:

— Electrical appliances which con- sume a large amount of wattage when turned on (CRT TVs, elec- tric tools etc.)

— Electrical appliances which have a switching power frequency

Model "E52-D" EDITED: 2010/ 10/ 25

Type B (if so equipped)

Main switch

Power outlet Pull up the cover and plug in.

SIC2648

SIC4725

The power outlet (plug type) is located on the front console. It can operate when the ignition switch in the ON position and the main switch (located on the instrument panel) is ON.

The specification of this power outlet is for use of a 120 volt, 150W (1.25A) power draw.

To turn on or off the power supply to the outlet, push the ON *1 or OFF *2
side of the main switch. When the switch is turned to the ON position, the indicator light *A will illuminate.

After using the power outlet, be sure to turn off the main switch.

CAUTION

. Make sure that there is no fluid or other foreign substance in the power outlet. Also, be sure not to connect or disconnect the outlet with wet hands or insert any metal objects into it. Doing so could result in an electric shock or malfunction. . Do not use with accessories that

2-40 Instruments and controls

STORAGE

(clocks etc.)

CUP HOLDERS

— Electrical appliances that mea- sure precise data (measuring equipment etc.)

— Certain other electrical appli-

ances (electric blankets etc.)

. Depending on the electrical appli- ance that is in use, some distorted noise may be audible when using the TV or radio.

. Be sure to turn the power switch of the electrical appliance used off before removing the plug from the power outlet.

. Do not use an extension cord with

multiple outlets.

CAUTION

. Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.

. Use only soft cups in the cup holder. Hard objects can injure you in an accident.

Black plate (117,1)

Instrument panel

SIC4726

Front

Instrument panel:

To open the cup holder, push the instrument panel *1 .

Instruments and controls 2-41

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (118,1)

Front side of the front center console

SIC4727

2nd row seat

3rd row seat

SIC4719

SIC4419

Back side of the front center console

2-42 Instruments and controls

SIC4654

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (119,1)

glasses holder while parking in direct sunlight. The heat may da- mage the glasses.

Instruments and controls 2-43

Model "E52-D" EDITED: 2010/ 10/ 25

SIC4720

SIC3589

Soft bottle holder Soft bottle holders are located on the front doors and sliding doors.

SUNGLASSES HOLDER (if so equipped)

CAUTION

. Do not use bottle holder for any other objects that could be thrown about in the vehicle and possibly injure people during sudden braking or an accident.

. Do not use bottle holder for open

liquid containers.

WARNING

Keep the sunglasses holder closed while driving to prevent an accident. To open the sunglasses holder, push *1 .

CAUTION

. Do not use for anything other than

glasses.

. Do not leave glasses in the sun-

Black plate (120,1)

SIC4647

SIC4729

INSTRUMENT LOWER BOX (if so equipped) To open the box, pull the knob.

To close, push the lid in until the lock latches.

GLOVE BOX

WARNING

Keep glove box lid closed while driving to help prevent injury in an accident or a sudden stop. To open the glove box, pull the handle *1 . To close, push the lid in until the lock latches. To lock *2 /unlock *3
the glove box, use the mechanical key. For the mechanical key usage, see “KEYS” in the “3. Pre-driving checks and adjustments” section.

2-44 Instruments and controls

Front

SIC4730

CONSOLE BOX Front To open the box, pull the knob. To close, push the lid in until the lock latches.

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (121,1)

SIC4721

SIC4731

2nd row center console

2. Push down the rear of the console box to

lock the console in place.

2nd row center console Pull up on lever *A to open the console box lid. To remove the 2nd row center console box: 1. Pull up on handle *B on rear of console and

tilt the console up.

2. Move the console box toward the rear of the

vehicle and lift out.

To reinstall the 2nd row center console box:

1. Tilt the console box forward and install the front of the console box so that the hook engages the slot in the base.

CARGO FLOOR BOX To open the cargo floor box lid, pull the strap *A . To hold lid open, secure the strap *B hook on the under side of cargo floor box lid.

to the

WARNING

To prevent injury in an accident or sudden stop, do not drive with the cargo floor box lids open. Always remove the strap *B from hook and close the cargo floor box lids before driving.

Instruments and controls 2-45

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (122,1)

lb (4 kg) to the hook.

Cargo area

SIC4732

HOOKS Cargo area The 4 hooks are located on the right and left side of the cargo area.

WARNING

. Always make sure that the cargo is properly secured. Use the suitable ropes and hooks.

. Unsecured cargo can become dan- gerous in an accident or sudden stop.

CAUTION

Do not apply a total load of more than 7
lb (3 kg) to the hook.

Seatbacks The hooks are located on the front and 3rd row seatbacks.

To use the hook on the seatbacks, push the lower side of the hook and pull it out.

Seatbacks

2-46 Instruments and controls

SIC4733

Do not apply a total load of more than 9

CAUTION

Model "E52-D" EDITED: 2010/ 10/ 25

information” section.

WARNING

. Drive extra carefully when the vehi- cle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack.

. Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sud- den or unusual handling maneuvers. . Roof rack load should be evenly

distributed.

. Do not exceed maximum roof rack

load weight capacity.

. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.

CAUTION

Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof

SIC4737

ROOF RACK (if so equipped) Always distribute the luggage evenly on the roof rack. Do not load more than 99 lb (45 kg) on the roof rails. Observe the maximum load limit shown on the crossbars or roof carriers when you attach them on the roof rails. Contact a NISSAN dealer for crossbar or other equipment information. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. or C.V.M.S.S. certification label (located on the driver’s door pillar). For more information regarding GVWR and GAWR, see “VEHICLE LOADING INFOR- MATION” in the “9. Technical and consumer

Black plate (123,1)

rack from the ground, use a ladder or stool.

Instruments and controls 2-47

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (124,1)

SUNSHADE (if so equipped)

WINDOWS

SIC3505

SIC4659

COAT HOOKS The coat hooks are equipped beside the rear personal lights.

CAUTION

Do not place items which are more than 2 lb (1 kg) on the hook.

CAUTION

Do not pull the sunshade in any direc- tion other than the up. This may da- mage the sunshade.

Sunshades are equipped on the 2nd and 3rd row seat windows. To raise the sunshade, pull the knob *A up and hang the sunshade on the hooks *B . To store the sunshade, remove the sunshade from the hooks and lower it.

2-48 Instruments and controls

POWER WINDOWS

WARNING

. Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the win- dow lock switch to prevent unex- pected use of the power windows.

. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols and become trapped in the window. Unattended children could become involved in serious acci- dents.

The power windows operate when the ignition switch is in the ON position or for about 45
seconds after the ignition switch is pushed to the OFF position. front passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled.

the driver’s or

If

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (125,1)

Locking passengers’ windows When the lock button *C is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.

SIC3283A

Front passenger side window

Main power window switch (driver’s side) 1. Driver side window 2. 3. Rear left passenger side window 4. Rear right passenger side window 5. Window lock button To open or close the window, push down *A or pull up *B the switch and hold it. The main switch (driver side switches) will open or close all the windows.

SIC3241

Passenger side power window switch The passenger side switch will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it.

Instruments and controls 2-49

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (126,1)

Auto reverse function

1. Push the ignition switch to the ON position.

2. Close the door.

3. Open the window completely by operating

the power window switch.

4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed completely.

5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.

6. Perform steps 2 through 5 above for other

windows.

If the power window automatic function does not operate properly after performing the pro- cedure above, have your vehicle checked by a NISSAN dealer.

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the window.

If the control unit detects something caught in the window as it is closing, the window will be immediately lowered.

The auto reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is pushed to the OFF position.

Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs.

If the windows do not close automatically If the power window automatic function (closing only) does not operate properly, perform the following procedure to initialize the power window system.

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3285

Automatic operation The automatic function is available for the switch that has an

mark on its surface.

To fully open or close the window, completely push down or pull up the switch and release it; it need not be held. The window will automatically open or close all the way. To stop the window, just push or the switch in the opposite direction.

lift

A light push or pull on the switch will cause the window to open or close until the switch is released.

2-50 Instruments and controls

AUTOMATIC MOONROOF The moonroof only operates when the ignition switch is in the ON position.

The automatic moonroof is operational for about 45 seconds, even if the ignition switch is pushed to the OFF position. If the driver’s door or the passenger’s door is opened during this period of about 45 seconds, power to the moonroof is canceled.

MOONROOF (if so equipped)

WARNING

In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.

. Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.

CAUTION

. Remove water drops, snow, ice or sand from the moonroof before opening.

. Do not place any heavy object on the moonroof or surrounding area.

Black plate (127,1)

SIC4643

FRONT MOONROOF Sunshade The sunshade will open automatically when the front moonroof is opened. However, it must be closed manually.

Sliding When the *A side of the switch is pushed, the front moonroof will fully open. When the *B side of the switch is pushed, the front moonroof will close. To stop the moonroof while closing, release the switch.

Tilting To tilt up, first close the moonroof.

Instruments and controls 2-51

Model "E52-D" EDITED: 2010/ 10/ 25

Push the *B side of the switch. The moonroof will automatically tilt up all the way. To tilt down, push the *A side of the switch. The roof will stop when the switch is released.

Black plate (128,1)

Tilting To tilt up, first close the moonroof, then push the switch to the tilt up position *B and release it; it does not need to be held. To tilt down the moonroof, push the switch to the tilt down position *A . Locking When the window lock button is pushed in, the rear moonroof cannot be operated. When the window lock position is pushed off, the rear moonroof can be operated. (See “POWER WINDOWS” earlier in this section.)

SIC4644

Auto-reverse function

REAR MOONROOF Rear moonroof operation switches are located on the front map light and rear ceiling.

Sunshade The sunshade will open automatically when the rear moonroof is opened. However, it must be closed manually.

Sliding To fully open or close the moonroof, push the switch to the open *A or close *B position and release. It does not need to be held. The roof will automatically open or close all the way. To stop the roof, push the switch once more while it is opening or closing.

WARNING

There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the moonroof.

If the control unit detects something caught in the moonroof when it is closing, the moonroof will be immediately opened.

The auto reverse function can be activated when the moonroof is closed by automatic operation when the ignition switch is in the ON position or

Model "E52-D" EDITED: 2010/ 10/ 25

2-52 Instruments and controls

moonroof operates inch by inch.)

4. After the moonroof stops moving, release the moonroof switch and within 4 seconds, push side *B again. The moonroof will automatically open once.

5. Within 0.5 seconds after

the moonroof stops moving, release the moonroof switch.

6. Check that

the moonroof now operates

normally.

If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.

for about 45 seconds after the ignition switch is pushed to the OFF position.

If the moonroof cannot be closed automatically when the auto reverse function activates due to a malfunction, push and hold the moonroof switch to the close position *B . Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.

IF THE FRONT OR REAR MOONROOF DOES NOT OPERATE If the front or rear moonroof does not operate properly, perform the following procedure to initialize the moonroof operation system. Initiali- zation can be performed for both the front moonroof and rear moonroof.

1.

If the moonroof is open, close it fully by pushing and holding the moonroof switch to the close position *B until the moonroof tilts up.

2. Release the moonroof switch, then push and side again for more than 10

hold the *B seconds.

3. Release the moonroof switch, then continue to push on the *B side again. The moonroof (The will operate in the close direction.

Black plate (129,1)

INTERIOR LIGHTS

SIC4745

MAP LIGHTS Push the button as illustrated to turn the light on or off.

Instruments and controls 2-53

Model "E52-D" EDITED: 2010/ 10/ 25

.

The driver’s door is unlocked.

The last open door excluding the lift gate is closed.

The interior light timer will be cancelled when:

The driver’s door is locked.

The ignition switch is pushed to the ON position.

When the rear personal light switch is in the ON position *C , the rear personal lights illuminate, regardless of any condition. When the switch is in the OFF position *A , the rear personal lights do not illuminate, regardless of any condition.

SIC2881

REAR PERSONAL LIGHTS The rear personal switch.

light has a three-position

*A : OFF*B : DOOR *C : ON When the switch is in the DOOR position *B , the light illuminates when a door is opened.

The interior light timer is equipped so that the interior light stays on for approximately 15
seconds when:

The ignition switch is pushed to the OFF or LOCK position.

2-54 Instruments and controls

Black plate (130,1)

SIC4746

INTERIOR LIGHT CONTROL SWITCH The interior light control switch has three positions: ON, DOOR and OFF.

ON position When the switch is in the ON position *1
map lights and rear personal nate.

lights will

the illumi-

DOOR position When the switch is in the DOOR position *2 , the map lights and rear personal lights will illuminate under the following conditions:

ignition switch is switched to the LOCK position

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (131,1)

MOOD LIGHTS

— remain on for about 15 seconds.

in any position

doors are unlocked by pushing the UN- LOCK button on the Intelligent Key or door handle request switch with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened and then closed with the ignition switch in the LOCK position

— remain on for about 15 seconds.

any door is opened with the ignition switch in the ACC or ON position

— remain on while the door

is opened. When the door is closed, the lights go off.

The lights will also turn off after 15
minutes when the lights remain illumi- nated after the ignition switch has been pushed to the OFF or LOCK position to prevent the battery from becoming dis- charged.

When the auto interior illumination is set to the OFF position (see “VEHICLE INFORMATION AND SETTINGS (models with center multi- function control panel)” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section), the lights will illuminate under the following condition:

any door is opened with the ignition switch

— remain on while the door

is opened. When the door is closed, the lights go off.

OFF position When the switch is in the OFF position *3 , the lights will not the condition.

regardless of

illuminate,

CAUTION

Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.

SIC4747

Map lights

The mood lights *A located in the following positions will illuminate whenever the headlight switch is in the

next to the map lights

position.

or

under the instrument panel

under the driver’s power window switch

Instruments and controls 2-55

Model "E52-D" EDITED: 2010/ 10/ 25

VANITY MIRROR LIGHTS

CARGO LIGHTS

SIC4660

The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.

When the cover is closed, the light will turn off.

The lights will turn off after 15 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

SIC2925

When the switch is in the DOOR position *A , the light illuminates while the lift gate is opened. When the lift gate is closed, the light will turn off. When the switch is in the OFF position *B , the light will turn off.

The lights will turn off after 15 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.

2-56 Instruments and controls

Black plate (132,1)

HomeLink® UNIVERSAL TRANSCEIVER (if so equipped)

HomeLink® Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink® Universal Transceiver: . Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.

Is powered by your vehicle’s battery. No separate batteries are required. the vehicle’s battery is discharged or is dis- connected, HomeLink® will retain all pro- gramming.

If

Once HomeLink® Universal Transceiver is programmed, retain the original transmit- ter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink® Universal Transceiver buttons should be erased for security purposes. For additional information, see “PRO- GRAMMING HomeLink®” later in this sec- tion.

the vehicle,

WARNING

. Do not use HomeLink® Universal Transceiver with any garage door opener that lacks safety stop and

Model "E52-D" EDITED: 2010/ 10/ 25

reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982.) A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.

. During programming procedure, your garage door or security gate may open or close. Make sure that people and objects are clear of the garage door, gate, etc. that you are programming.

. Your vehicle’s engine should be turned off while programming HomeLink® Universal Transceiver.

PROGRAMMING HomeLink® To program your HomeLink® Transceiver to operate a garage door, gate, or entry door opener, home or office lighting, you need to be at the same location as the device. Note: Garage door openers (manufactured after

Black plate (133,1)

1996) have “rolling code protection”. To pro- gram a garage door opener equipped with “rolling code protection”; you will need to use a ladder to get up to the garage door opener motor to be able to access the “smart or learn” program button.

SIC3612

1. To begin, push and hold the 2 outer Home- Link® buttons (to clear the memory) until the indicator light *A blinks (after 20 seconds). Release both buttons.

2. Position the end of the hand-held transmitter 1 to 3 in (20 to 70 mm) away from the HomeLink® surface.

Instruments and controls 2-57

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (134,1)

5.

button - releasing when the device begins to activate. If the indicator light on HomeLink® blinks rapidly for two seconds and then turns solid,