2011 Nissan Quest Owners Manual

(See “BRAKE SYSTEM” in the “5. Starting and driving” section.)

or

Brake warning light

This light functions for both the parking brake and the foot brake systems.

Parking brake indicator:

When the ignition switch is in the ON position, the light comes on when the parking brake is applied.

Low brake fluid warning light:

When the ignition switch is in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running with the parking brake not applied, stop the vehicle and perform the following:

1. Check the brake fluid level. Add brake fluid as necessary. (See “BRAKE FLUID” in the “8. Maintenance and do-it-yourself” sec-

2.

is correct, have the If the brake fluid level warning system checked by a NISSAN dealer.

Anti-lock Braking System (ABS) warning indicator:

When the parking brake is released and the brake fluid level is sufficient, if both the brake warning light and the Anti-lock Braking System (ABS) warning light illuminate, it may indicate the ABS is not functioning properly. Have the brake system checked, and if necessary re- paired, by a NISSAN dealer promptly. (See “Anti-lock Braking System (ABS) warning light” earlier in this section.)

WARNING

. Your brake system may not be working properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive care- fully to the nearest service station for repairs. Otherwise, have your vehicle towed because driving it could be dangerous.

. Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stop-

Black plate (87,1)

ping distance and braking will re- quire greater pedal effort as well as pedal travel.

If the brake fluid level is below the minimum or MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.

Blind Spot Warning (BSW) sys- tem warning light (orange; if so equipped)

If the light comes on in orange and remains on, it may indicate that the BSW system is not functioning properly. Although the vehicle is still driveable, have the system checked by a NISSAN dealer. See “BLIND SPOT WARNING (BSW) SYSTEM” in the “5. Starting and driving” section.

Charge warning light

If the light comes on while the engine is running, it may indicate the charging system is not functioning properly. Turn the engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see a NISSAN dealer immediately.

Instruments and controls 2-11

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (88,1)

CAUTION

Do not continue driving if the alternator belt is loose, broken or missing.

Engine oil pressure warning light

This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop.

The engine oil pressure warning light is not designed to indicate a low oil level. Use the dipstick to check the oil level. (See “ENGINE OIL” in the “8. Maintenance and do-it- yourself” section.)

CAUTION

Running the engine with the engine oil pressure warning light on could cause serious damage to the engine almost immediately. Such damage is not cov- ered by warranty. Turn off the engine as soon as it is safe to do so.

2-12 Instruments and controls

Hydraulic pump electric power steering warning light

When the ignition switch is in the ON position, the hydraulic pump electric power steering illuminates. After starting the warning light engine, the hydraulic pump electric power steering warning light turns off. This indicates that the electric power steering system is operational.

If the hydraulic pump electric power steering warning light illuminates while the engine is running, it may indicate the hydraulic pump electric power steering system is not functioning properly and may need servicing. Have the hydraulic pump electric power steering system checked by a NISSAN dealer. (See “HYDRAU- LIC PUMP ELECTRIC POWER STEERING SYSTEM” in the “5. Starting and driving” section.)

Intelligent Key system warning light

After the ignition switch is pushed to the ON position, this light comes on for about 2 seconds and then turns off.

This light warns of a malfunction with the Intelligent Key system.

If

the light comes on while the engine is

it may be impossible to start

stopped, the engine. If the light comes on while the engine is running, you can drive the vehicle. However in these cases, contact a NISSAN dealer for repair as soon as possible.

Low tire pressure warning light

Your vehicle is equipped with a Tire Pressure Monitoring System (TPMS) that monitors the tire pressure of all tires except the spare.

The low tire pressure warning light warns of low tire pressure or indicates that the TPMS is not functioning properly.

After the ignition switch is pushed ON, this light illuminates for about 1 second and turns off.

Low tire pressure warning:

the vehicle is being driven with low tire If pressure, illuminate. A CHECK TIRE PRESSURE warning also appears on the dot matrix liquid crystal display.

the warning light will

When the low tire pressure warning light illuminates, you should stop and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. The low tire pressure warning light does not automatically turn off when the tire pressure is adjusted. After the tire is inflated to the recommended pressure, the vehicle must be

Model "E52-D" EDITED: 2010/ 10/ 25

driven at speeds above 16 MPH (25 km/h) to activate the TPMS and turn off the low tire pressure warning light. Use a tire pressure gauge to check the tire pressure.

The CHECK TIRE PRESSURE warning is active as long as the low tire pressure warning light remains illuminated.

For additional information, see “TIRE PRES- SURE MONITORING SYSTEM (TPMS)” in the “5. Starting and driving” section and “TIRE PRESSURE MONITORING SYSTEM (TPMS)” in the “6. In case of emergency” section.

TPMS malfunction:

If the TPMS is not functioning properly, the low tire pressure warning light will flash for approxi- mately 1 minute when the ignition switch is pushed ON. The light will remain on after the 1
minute. Have the system checked by a NISSAN dealer. The CHECK TIRE PRESSURE warning does not appear if the low tire pressure warning light illuminates to indicate a TPMS malfunction.

For additional information, see “TIRE PRES- SURE MONITORING SYSTEM (TPMS)” in the “5. Starting and driving” section. For the CHECK TIRE PRESSURE warning, see “DOT MATRIX LIQUID CRYSTAL DISPLAY” later in this section.

WARNING

If the light does not illuminate with the ignition switch pushed ON, have the vehicle checked by a NISSAN dealer as soon as possible.

If the light illuminates while driving, avoid sudden steering maneuvers or abrupt braking, reduce vehicle speed, pull off the road to a safe location and stop the vehicle as soon as possible. Driving with un- der-inflated tires may permanently damage the tires and increase the likelihood of tire failure. Serious vehicle damage could occur and may lead to an accident and could result in serious personal injury. Check the tire pressure for all four tires. Adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label to turn the low tire pressure warning light OFF. If the light still illuminates while driv- ing after adjusting the tire pressure, a tire may be flat. If you have a flat tire, replace it with a spare tire as soon as possible.

Black plate (89,1)

. When a spare tire is mounted or a wheel is replaced, the TPMS will not function and the low tire pressure warning light will flash for approxi- mately 1 minute. The light will remain on after 1 minute. Contact your NISSAN dealer as soon as possible for tire replacement and/ or system resetting.

. Replacing tires with those not ori- ginally specified by NISSAN could affect the proper operation of the TPMS.

CAUTION

The TPMS is not a substitute for the regular tire pressure check. Be sure to check the tire pressure regularly.

If the vehicle is being driven at speeds of less than 16 MPH (25
km/h), the TPMS may not operate correctly.

. Be sure to correctly install

the specified size of tires to the four wheels.

Instruments and controls 2-13

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (90,1)

fastened when the front passenger’s seat is occupied. For approximately 5 seconds after the ignition switch is in the ON position, the system does not activate the warning light for the front passenger.

See “SEAT BELTS” in the “1. Safety — Seats, seat belts and supplemental restraint system” section for precautions on seat belt usage.

Supplemental air bag warning light

After pushing the ignition switch to the ON position, the supplemental air bag warning light will illuminate. The supplemental air bag warning light will turn off after about 7 seconds if the supplemental front air bag and supplemental side air bag, curtain side-impact air bag systems and/or pretensioner seat belt are operational.

If any of the following conditions occur, the front air bag, side air bag, curtain air bag and pretensioner systems needs servicing and your vehicle must be taken to your nearest NISSAN dealer.

The supplemental air bag warning light remains on after approximately 7 seconds.

The supplemental air bag warning light flashes intermittently.

The supplemental air bag warning light does not come on at all.

Unless checked and repaired, the Supplemental Restraint Systems (air bag systems) and/or the pretensioners may not function properly.

For additional information, see “SUPPLEMEN- TAL RESTRAINT SYSTEM” in the “1. Safety — Seats, seat belts and supplemental restraint system” section.

WARNING

If the supplemental air bag warning light is on, it could mean that the front air bag, side air bag, curtain air bag and/or pretensioner systems will not operate in an accident. To help avoid injury to yourself or others, have your vehicle checked by a NISSAN dealer as soon as possible.

Vehicle Dynamic Control (VDC) warning light

The light will blink when the VDC system or the traction control system is operating, thus alerting the driver that the vehicle is nearing its traction limits. The road surface may be slippery.

When the vehicle dynamic control warning light illuminates when the vehicle dynamic control system is turned on, this light alerts the driver to

Model "E52-D" EDITED: 2010/ 10/ 25

Master warning light

When the ignition switch is in the ON position, the master warning light illuminates if any of the following are displayed on the dot matrix liquid crystal display: . No key warning

Low fuel warning

Low washer fluid warning

. Parking brake release warning . Door/lift gate open warning . Check tire pressure warning

Loose fuel cap warning

See “DOT MATRIX LIQUID CRYSTAL DIS- PLAY” later in this section.

Seat belt warning light and chime

The light and chime remind you to fasten seat belts. The light illuminates whenever the ignition switch is pushed to the ON position, and will remain illuminated until the driver’s seat belt is fastened. At the same time, the chime will sound for approximately 6 seconds unless the driver’s seat belt is securely fastened.

The seat belt warning light passenger will 2-14 Instruments and controls

the front illuminate if the seat belt is not

for

Black plate (91,1)

that

the fact the vehicle dynamic control system’s fail-safe mode is operating, for example the vehicle dynamic control system may not be functioning properly. Have the system checked by a NISSAN dealer. If a malfunction occurs in the system, the vehicle dynamic control system function will be canceled but the vehicle is still driveable. For additional information, see “VE- HICLE DYNAMIC CONTROL (VDC) SYSTEM” in the “5. Starting and driving” section of this manual.

INDICATOR LIGHTS

Continuously Variable Transmis- sion (CVT) position indicator light

When the ignition switch is pushed to the ON position, the indicator shows the automatic selector shift position. (See “CONTINUOUSLY VARIABLE TRANSMISSION (CVT)” in the “5. Starting and driving” section.)

Cruise indicator light

Cruise main switch indicator:

This light illuminates when the cruise control main switch is pushed. The light turns off when the main switch is pushed again. When the cruise main switch indicator light illuminates, the cruise control system is operational. (See

“CRUISE CONTROL” in the “5. Starting and driving” section.)

Low beam indicator light

Cruise malfunction:

the cruise indicator

light blinks while the If engine is running, it may indicate the cruise control system is not functioning properly. Have the system checked by a NISSAN dealer. (See “CRUISE CONTROL” in the “5. Starting and driving” section.)

Front passenger air bag status light

The front passenger air bag status light ( will be lit and the passenger front air bag will be OFF depending on how the front passenger seat is being used.

For front passenger air bag status light opera- tion, see “NISSAN ADVANCED AIR BAG SYSTEM (front seats)” in the “1. Safety — Seats, seat belts and supplemental restraint system” section of this manual.

High beam indicator light

This light comes on when the headlight high beam is on and goes out when the low beam is selected.

The light comes on when the front park, side marker, tail and license plate lights are on.

Malfunction Indicator Light (MIL)

the malfunction indicator

If light comes on steady or blinks while the engine is running, it may indicate a potential emission control.

The malfunction indicator light may also come on steady if the fuel-filler cap is loose or missing, or if the vehicle runs out of fuel. Check to make sure the fuel-filler cap is installed and closed tightly, and that the vehicle has at least 3 US gallons (11.4 liters) of fuel in the fuel tank.

light should After a few driving trips, the turn off if no other potential emission control system malfunction exists.

If this indicator light remains on for 20 seconds and then blinks for 10 seconds when the engine is not running, it indicates that the vehicle is not ready for an emission control system inspection/ maintenance test. (See “READINESS FOR INSPECTION/MAINTENANCE (I/M) TEST” in the “9. Technical and consumer information” section.)

Instruments and controls 2-15

Model "E52-D" EDITED: 2010/ 10/ 25

Operation:

blinking and remain on.

The malfunction indicator light will come on in one of two ways: . Malfunction indicator light on steady — An emission control system has been detected. Check the fuel-filler cap if the LOOSE FUEL CAP warning appears on the dot matrix liquid crystal display. If the fuel-filler cap is loose or missing, tighten or install the cap and continue to drive the vehicle. The light should turn off after a few driving trips. light does not turn off after a few If the driving trips, have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

. Malfunction indicator light blinking — An engine misfire has been detected which may damage the emission control system.

To reduce or avoid emission control system damage:

a) Do not drive at speeds above 45 MPH

(72 km/h).

b) Avoid hard acceleration or deceleration.

c) Avoid steep uphill grades.

d) If possible, reduce the amount of cargo

being hauled or towed.

The malfunction indicator

light may stop

2-16 Instruments and controls

Have the vehicle inspected by a NISSAN dealer. You do not need to have your vehicle towed to the dealer.

CAUTION

Continued vehicle operation without having the emission control system and repaired as necessary could lead to poor driveability, reduced fuel econ- omy, and possible damage to the emis- sion control system.

Overdrive off indicator light

The overdrive off indicator light illuminates when the overdrive off mode is selected.

For additional information, see ““CONTINU- OUSLY VARIABLE TRANSMISSION (CVT)” in the “5. Starting and driving” section of this manual.

Security indicator light

The light blinks when the ignition switch is in the ACC, OFF or LOCK position. This function indicates the security system equipped on the vehicle is operational.

Black plate (92,1)

If the security system is malfunctioning, this light will remain on while the ignition switch is in the ON position. For additional information, see “SECURITY SYSTEMS” later in this section.

Turn signal/hazard indicator lights

The light flashes when the turn signal switch lever or hazard switch is turned on.

Vehicle Dynamic Control (VDC) off indicator light

The light comes on when the vehicle dynamic control off switch is pushed to OFF. This indicates that the vehicle dynamic control system and traction control system are not operating.

AUDIBLE REMINDERS Key reminder chime A chime will sound if the driver side door is opened while the ignition switch is pushed to the ACC position. Make sure the ignition switch is pushed to the OFF position, and take the Intelligent Key with you when leaving the vehicle.

Light reminder chime A chime will sound when the driver side door is or opened with the light switch in the position and the ignition switch in the ACC

Model "E52-D" EDITED: 2010/ 10/ 25

or OFF position.

Turn the light switch off when you leave the vehicle.

The chime will also sound for 2 seconds when the ignition switch is turned to the OFF position with the fog lights on while the headlight switch is in the AUTO position.

Parking brake reminder chime The chime will sound if the vehicle is driven at more than 4 MPH (7 km/h) with the parking brake applied. Stop the vehicle and release the parking brake.

Brake pad wear warning The disc brake pads have audible wear warn- ings. When a brake pad requires replacement, it will make a high pitched scraping sound when the vehicle is in motion. This scraping sound will first occur only when the brake pedal is depressed. After more wear of the brake pad, the sound will always be heard even if the brake pedal is not depressed. Have the brakes checked as soon as possible if the warning sound is heard.

Black plate (93,1)

DOT MATRIX LIQUID CRYSTAL DISPLAY

SIC4715

The dot matrix liquid crystal display *1
is located in the speedometer, and it displays, the key operation information and other warn- ings and information.

For the detail about the Intelligent Key System, see “INTELLIGENT KEY SYSTEM” in the “3. Pre-driving checks and adjustments” section.

Instruments and controls 2-17

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (94,1)

INDICATORS FOR OPERATION 1. Engine start operation indicator This indicator appears when the selector lever is in the P (Park) position.

This indicator means that the engine will start by

2-18 Instruments and controls

pushing the ignition switch with the brake pedal depressed.

You can start the engine directly in any position.

2. NO KEY warning This warning appears in either of the following conditions.

SIC4716

No key inside the vehicle:

The warning appears when the door is closed

Model "E52-D" EDITED: 2010/ 10/ 25

with the Intelligent Key left outside the vehicle and the ignition switch in the ACC or ON position. Make sure that the Intelligent Key is inside the vehicle.

Unregistered key:

The warning appears when the ignition switch is pushed from the LOCK position and the key cannot be recognized by the system. You cannot start the engine with an unregistered key. Use the registered key.

See “INTELLIGENT KEY SYSTEM” in the “3. Pre-driving checks and adjustments” section for more details.

3. SHIFT “P” warning This warning appears when the ignition switch is pushed to stop the engine with the selector lever in any position except the P (Park) position.

If this warning appears, move the selector lever to the P (Park) position or push the ignition switch to the ON position.

An inside warning chime will also sound. (See “INTELLIGENT KEY SYSTEM” in the “3. Pre- driving checks and adjustments” section.)

4. “PUSH” warning This warning appears when the selector lever is moved to the P (Park) position with the ignition switch in the ACC position after the SHIFT “P”

warning appears.

To push the ignition switch to the OFF position, perform the following procedure:

SHIFT “P” warning ? (Move the selector lever to “P”) ? PUSH warning ? (Push the ignition switch ? ignition switch position is turned to ON) ? PUSH warning ? (Push the ignition switch ? ignition switch position is turned to OFF)

5. Key battery discharge indicator This indicator appears when the key battery is running out of power.

If this indicator appears, replace the battery with a new one. (See “INTELLIGENT KEY BATTERY REPLACEMENT” in the “8. Maintenance and do-it-yourself” section.)

6. Engine start operation for Intelligent Key system indicator This indicator appears when the Intelligent Key battery is running out of power and when the Intelligent Key System and vehicle are not communicating normally.

this indicator appears,

If touch the ignition switch with the Intelligent Key while depressing the brake pedal. (See “INTELLIGENT KEY BATTERY DISCHARGE” in the “5. Starting and driving” section.)

Black plate (95,1)

7. Parking brake release warning This warning appears when the vehicle speed is above 4 MPH (7 km/h) and the parking brake is applied. Stop the vehicle and release the parking brake.

8. Low fuel warning This warning appears when the fuel level in the tank is getting low. Refuel as soon as it is convenient, preferably before the fuel gauge reaches the empty (0) position.

There is a small reserve of fuel remaining in the tank when the fuel gauge reaches the empty (0) position.

9. Low washer fluid warning This warning appears when the washer tank fluid is at a low level. Add washer fluid as necessary. (See “WINDOW WASHER FLUID” in the “8. Maintenance and do-it-yourself” section.)

10. Door/lift gate open warning (ignition switch is in the ON position) This warning appears if any of the doors and/or the lift gate are open or not closed securely. The vehicle icon indicates which door is open on the display.

11. Loose fuel cap warning This warning appears when the fuel-filler cap is not the vehicle has

tightened correctly after

Instruments and controls 2-19

Model "E52-D" EDITED: 2010/ 10/ 25

been refueled. (See “FUEL-FILLER CAP” in the “3. Pre-driving checks and adjustments” sec- tion.)

12. Check tire pressure warning This warning appears when the low tire pressure warning light in the meter illuminates and low tire pressure is detected. If this warning appears, stop the vehicle and adjust the tire pressure to the recommended COLD tire pressure shown on the Tire and Loading Information label. (See “Low tire pressure warning light” earlier in this section and “TIRE PRESSURE MONITORING SYSTEM (TPMS)” in the “5. Starting and driving” section.)

13. “TIMER” indicator This indicator appears when the set “timer” indicator activates. You can set the time for up to 6 hours. (See “TRIP COMPUTER” later in this section.)

14. Low outside temperature warning This warning appears if the outside temperature is below 378F (38C). The warning can be set not to be displayed. (See “TRIP COMPUTER” later in this section.)

2-20 Instruments and controls

SIC4237

INDICATORS FOR MAINTENANCE 1. Engine oil replacement indicator This indicator appears when the set time comes for changing the engine oil. You can set or reset the distance for changing the engine oil. (See “TRIP COMPUTER” later in this section.)

Black plate (96,1)

2. Oil filter replacement indicator This indicator appears when the set time comes for replacing the oil filter. You can set or reset the distance for replacing the oil filter. (See “TRIP COMPUTER” later in this section.)

3. Tire replacement indicator This indicator appears when the set time comes for replacing tires. You can set or reset the distance for replacing tires. (See “TRIP COM- PUTER” later in this section.)

4. “OTHER” indicator This indicator appears when the set time comes for replacing items other than the engine oil, oil filter and tires. You can set or reset the distance for replacing the items. (See “TRIP COMPU- TER” later in this section.)

More maintenance reminders are also available on the center display. (models with center multi- function control panel) (See “HOW TO USE INFO BUTTON” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.)

Model "E52-D" EDITED: 2010/ 10/ 25

Current and average fuel consumption ? Average fuel consumption and speed ? Elapsed time and trip odometer ? Distance to empty (dte) ? Outside air temperature (ICY) ? Setting ? Warning check

SIC3580

TRIP COMPUTER Switches for the trip computer are located on the right side of the combination meter panel. To operate the trip computer, push the side of the switches as shown above. *A *B When the ignition switch is pushed to the ON position, modes of the trip computer can be selected by pushing the

switch *A .

switch

switch

switch *A Each time the display will change as follows:

is pushed, the

Black plate (97,1)

SIC4700

Current and average fuel consumption (MPG, l (liter)/100 km or km/l) The current and average fuel consumption mode shows the current and average fuel consump- tion.

Instruments and controls 2-21

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (98,1)

vehicle speed since the last reset. Resetting is switch *B for longer done by pushing the than 1 second. (The average fuel consumption is also reset at the same time.)

The display is updated every 30 seconds. The first 30 seconds after a reset, the display shows “——”.

SIC4701

Elapsed time and trip odometer (miles or km)

Elapsed time:

The elapsed time mode shows the time since the last reset. The displayed time can be reset switch *B for longer than by pushing the 1 second. (The trip odometer is also reset at the same time.)

Trip odometer:

The trip odometer mode shows the total distance the vehicle has been driven since the last reset. Resetting is done by pushing the switch *B than 1 second. elapsed time is also reset at the same time.)

longer

(The

for

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3674

Average fuel consumption (MPG, l/100
km or km/l) and speed (MPH or km/h)

Fuel consumption:

The average fuel consumption mode shows the average fuel consumption since the last reset. switch *B Resetting is done by pushing the for longer than 1 second. (The average speed is also reset at the same time.)

The display is updated every 30 seconds. At about the first 1/3 mile (500 m) after a reset, the display shows “——”.

Speed:

The average speed mode shows the average

2-22 Instruments and controls

Black plate (99,1)

pushed to the OFF position may continue to be displayed.

. When driving uphill or rounding curves, the fuel in the tank shifts, which may momenta- rily change the display.

SIC4703
Outside air temperature (ICY — 8F or 8C) The outside air temperature is displayed in 8F or 8C in the range of −22 to 1408F (−30 to 608C).

The outside air temperature mode includes a low temperature warning feature. If the outside air temperature is below 378F (38C), the warning is displayed on the screen.

The outside temperature sensor is located in front of the radiator. The sensor may be affected by road or engine heat, wind directions and other driving conditions. The display may differ from the actual outside temperature or the temperature displayed on various signs or bill- boards.

Instruments and controls 2-23

Model "E52-D" EDITED: 2010/ 10/ 25

SIC4702

Distance to empty (dte — miles or km) The distance to empty (dte) mode provides you with an estimation of the distance that can be driven before refueling. The dte is constantly being calculated, based on the amount of fuel in the fuel tank and the actual fuel consumption.

The display is updated every 30 seconds.

The dte mode includes a low range warning feature. level is low, the warning is displayed on the screen.

If the fuel

level drops even lower, the dte

When the fuel display will change to “——”.

If the amount of fuel added is small, the display just before the ignition switch is

Black plate (100,1)

ALERT:

. OTHER

Alert menu can be set to notify the following items.

TIMER

Select this submenu to specify when the “TIMER” indicator activates.

Select this submenu and set or reset the distance for replacing items other than the engine oil, oil filter and tires.

To return to the top page of the setting mode, select “BACK”.

ICY

Select outside temperature warning.

this submenu to display the low

To return to the top page of the setting mode, select “BACK”.

MAINTENANCE:

The maintenance intervals of the following items can be set or reset for the reminders. . OIL

Select distance for changing the engine oil.

this submenu to set or reset

the

FILTER

Select distance for replacing the oil filter.

this submenu to set or reset

the

TIRE

OPTIONS:

The 3 option menus can be set preference.

LANGUAGE

to your

Select French or Spanish for display.

this submenu to choose English,

. UNIT

Select this submenu to choose the unit from MPG or l/100 km.

. EFFECTS

Select this menu to set scribed below to on or off.

the effects de-

— The indicator needles sweep in the meters and the ring illumination will be brightened gradually when the engine is started.

Select distance for replacing tires.

this submenu to set or reset

the

To return to the top page of the setting mode, select “BACK”.

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3678

Setting Setting cannot be made while driving. A message “Setting can only be operated when stopped” is also displayed on the dot matrix crystal display. switch *A and

switch *B are The used in the setting mode to select and decide a menu.

SKIP:

Push the warning check mode.

switch *A

to move to the

Push the

switch *B to select other menus.

2-24 Instruments and controls

Black plate (101,1)

SECURITY SYSTEMS

to move to the

SKIP:

Push the warning check mode.

switch *A

Push the

DETAIL:

switch *B to select other menus.

This item is available only when a warning is displayed.

Select this menu to see the details of warnings.

SIC3993

Warning check To see if there are any of the following warnings and corresponding details, select this menu. . No key warning

Low fuel warning

Low washer fluid warning

. Parking brake release warning . Door/lift gate open warning . Check tire pressure warning

Loose fuel cap warning

SIC4717

Your vehicle has two types of security systems, as follows: . Vehicle security system . NISSAN Vehicle Immobilizer System

The security condition will be shown by the security indicator light.

VEHICLE SECURITY SYSTEM The vehicle security system provides visual and audio alarm signals if someone opens the doors or lift gate when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a vibration occurs.

Instruments and controls 2-25

Model "E52-D" EDITED: 2010/ 10/ 25

The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your Intelligent Key(s) in the vehicle, and always lock it when un- attended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.

Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features.

2-26 Instruments and controls

SIC2045

How to arm the vehicle security system 1. Close all windows.

The system can be armed even if the windows are open.

2. Push the ignition switch to the OFF position.

3. Remove the Intelligent Key from the vehicle.

4. Close all doors and lift gate. Lock all doors. The doors can be locked with the Intelligent Key, door handle request switch, power door lock switch or mechanical key.

5. Confirm that

the security indicator

light comes on. The security indicator light stays on for about 30 seconds. The vehicle

Black plate (102,1)

security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is pushed to ACC or ON, the system will not arm.

Even when the driver and/or passengers are in the vehicle, the system will activate with all doors and lift gate locked with the ignition switch in the LOCK position. When pushing the ignition switch to the ACC or ON position, the system will be released.

Vehicle security system activation The vehicle security system will give the follow- ing alarm:

The headlights blink and the horn sounds intermittently.

The alarm automatically turns off after approximately 1 minute. However, the alarm reactivates if the vehicle is tampered with again.

The alarm is activated by: . Unlocking the door or opening the lift gate without using the button on the Intelligent Key, the door handle request switch or the

Model "E52-D" EDITED: 2010/ 10/ 25

mechanical key. (Even if the door is opened by releasing the door inside lock knob, the alarm will activate.)

How to stop an activated alarm The alarm will stop by unlocking a door by pushing the unlock button on the Intelligent Key, the door handle request switch or using the mechanical key. The alarm will not stop if the ignition switch is pushed to the ACC or ON position.

If the system does not operate as de- scribed above, have it checked by a NISSAN dealer.

NISSAN VEHICLE IMMOBILIZER SYS- TEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered Intelligent Key. Never leave these keys in the vehicle.

For USA:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

Black plate (103,1)

operation.

Note: Changes or modifications not ex- pressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For Canada:

This device complies with RSS-210 of Industry Canada. Operation is subject to the following two conditions:

(1) this device may not cause interference, and (2) this device must accept any inter- ference, including interference that may cause undesired operation of the device.

SIC2045

Security indicator light The security indicator light is located on the meter panel. the NISSAN Vehicle Immobilizer System.

indicates the status of

It

The light blinks after the ignition switch is in the LOCK, ACC or OFF position. This function indicates the security systems equipped on the vehicle are operational.

If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position.

If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System

Instruments and controls 2-27

Model "E52-D" EDITED: 2010/ 10/ 25

service as soon as possible. Please bring all Intelligent Keys that you have when visiting a NISSAN dealer for service.

Black plate (104,1)

WINDSHIELD WIPER AND WASHER SWITCH

WARNING

mix the washer fluid concentrate and water.

In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

. Do not

fill

the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to

2-28 Instruments and controls

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (105,1)

REAR WINDOW WIPER AND WASHER SWITCH

WARNING

In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.

CAUTION

. Do not operate the washer continu-

ously for more than 30 seconds.

. Do not operate the washer if the

reservoir tank is empty.

the factory default setting. To turn this function on and off, see “HOW TO USE SETTING BUTTON” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.

*2 LO — continuous low speed operation *3 HI — continuous high speed operation Push the lever up *4
operation of the wiper. Pull the lever toward you *5
to operate the washer. Then the wiper will also operate several times.

(MIST) to have one sweep

. Do not

fill

the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.

. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate

Instruments and controls 2-29

Model "E52-D" EDITED: 2010/ 10/ 25

SIC3664

The windshield wiper and washer operates when the ignition switch is in the ON position.

Push the lever down to operate the wiper at the following speed: *1

INT — intermittent operation can be ad- justed by turning the knob toward *A (Slower) or *B (Faster). When the speed sensing wiper interval function (models with center multi-function control panel) is turned on, the intermittent operation speed varies in accordance with the vehicle speed. (For example, when the vehicle speed is high, the intermittent operation speed will be faster.) Note that the function is set to disabled as

Black plate (106,1)

REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH

SIC3666

SIC4718

The rear window wiper and washer operate when the ignition switch is in the ON position.

Turn the switch clockwise from the OFF position to operate the wiper. *1

Intermittent (INT) — intermittent operation (not adjustable)

tion

*2 Low (ON) — continuous low speed opera- Push the switch forward *3
to operate the washer. Then the wiper will also operate several times.

To defog/defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the switch *1 on. The indicator light *2 will come on. Push the switch again to turn the defroster off.

It will automatically turn off in approximately 15
minutes.

CAUTION

When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.

Model "E52-D" EDITED: 2010/ 10/ 25

and water.

If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper.

2-30 Instruments and controls

HEADLIGHT AND TURN SIGNAL SWITCH

XENON HEADLIGHTS (if so equipped)

WARNING

HIGH VOLTAGE

. When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.

. Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to a NISSAN dealer and have the headlights adjusted correctly.

When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.

The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn

Black plate (107,1)

off the headlights for short intervals (for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon head- lights is not reduced.

If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.

SIC3668

HEADLIGHT SWITCH Lighting *1 Turn the switch to the

position:

The front park, side marker, plate and instrument lights will come on.

tail,

license

*2 Turn the switch to the

position:

Headlights will come on and all the other lights remain on.

Instruments and controls 2-31

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (108,1)

The autolight system can turn on the headlights automatically when it is dark and turn off the headlights when it is light.

The headlights will also be turned on automa- tically at twilight or in rainy weather (when the windshield wiper is operated continuously) (if so equipped).

If the ignition switch is pushed to the OFF position and one of the doors is opened and this condition is continued, the headlights remain on for 5 minutes.

Automatic headlights off delay:

You can keep the headlights on for up to 180
seconds after you push the ignition switch to OFF and open any door then close all the doors.

the period of

the automatic You can adjust headlights off delay from 0 seconds (OFF) to 180 seconds. The factory default setting is 45
seconds.

For automatic headlights off delay setting, see “Light Off Delay” in the “4. Monitor, heater, air conditioner, audio, phone and voice recognition systems” section.

SIC3669

Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically.

To set the autolight system:

1. Make sure the headlight switch is in the

AUTO position *1 .

2. Push the ignition switch to the ON position.

3. The autolight system automatically turns the

headlights on and off.

SIC4722

Be sure not to put anything on top of the photo sensor *A located on the top of the instrument panel. The photo sensor con- trols the autolight; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate.

To turn the autolight system off, turn the switch to the OFF,

position.

or

2-32 Instruments and controls

Model "E52-D" EDITED: 2010/ 10/ 25

When the headlight switch is in the position while the ignition switch is in the ON position, the lights will automatically turn off 5
minutes after the ignition switch has been pushed to the OFF position.

or

When the headlight switch remains in the or position after the lights automatically turn off, the lights will turn on when the ignition switch is pushed to the ON position.

CAUTION

. When you turn on the headlight switch again after the lights auto- matically turn off, the lights will not turn off automatically. Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, other- wise the battery will be discharged. . Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically.

SIC3670

Headlight beam select *1 To select the low beam, put the lever in the

neutral position as shown.

*2 To select the high beam, push the lever

forward while the switch is in the position. Pull it back to select the low beam. *3 Pulling the lever toward you will flash the headlight high beam even when the head- light switch is in the OFF position.

Battery saver system A chime will sound when the driver side door is or opened with the light switch in the position and the ignition switch in the ACC,

OFF or LOCK position.

Black plate (109,1)

SIC2275

Headlight aiming control (if so equipped) Depending on the number of occupants in the vehicle and the load it is carrying, the headlight axis may be higher than desired. If the vehicle is traveling on a hilly road, the headlights may directly hit the rearview mirror of the vehicle ahead or the oncoming vehicle. The light axis can be lowered with the operation of the switch.

the windshield of

The larger the number designated on the switch, the lower the axis.

When traveling with no heavy load or on a flat road, select position 0.

Instruments and controls 2-33

Model "E52-D" EDITED: 2010/ 10/ 25

WARNING

WARNING

When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.

Xenon headlights (if so equipped) are extremely bright compared to conven- tional headlights. If the xenon head- lights hit the rearview mirror of the vehicle ahead or the windshield of oncoming vehicle, the driver of these vehicles may have difficulty driving because of the brightness. Use the headlight aiming control switch to low- er the light axis. See “XENON HEAD- LIGHTS” earlier in this section for additional information.

Daytime running light system (Canada only) The daytime running lights automatically illumi- nate when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the OFF position. Turn the position or position for full headlight switch to the illumination when driving at night.

in the

If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is pushed to the OFF position. 2-34 Instruments and controls

Black plate (110,1)

SIC3585

Instrument brightness control The instrument brightness control operates when the ignition switch is in the ON position. Pushing the control switch *A once will change the brightness to the night mode. Pushing the control switch *B once will change the brightness to the day mode.

the brightness of

To adjust instrument panel lights, push the control switches. Pushing the upper switch *A will brighten the lights. When the brightness reaches the maximum level, a beep will sound. The lower switch *B dims the lights. Repeatedly pushing the lower switch will turn the lights off and a beep will sound.

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (111,1)

HAZARD WARNING FLASHER SWITCH

SIC3671

SIC3672

SIC2574

TURN SIGNAL SWITCH *1 Turn signal Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. *2 Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flashing.

FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight position, then turn the switch switch to the position. To turn them off, turn the to the switch to the OFF position.

The headlights must be on for the fog lights to operate.

When the headlight switch is in the AUTO position (if so equipped):

Turning the fog light switch to the position will turn on the headlights, fog lights and the other lights while the ignition switch is in the ON position or the engine is running.

Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights will flash.

WARNING

If stopping for an emergency, be sure to move the vehicle well off the road.

. Do not use the hazard warning flashers while moving on the high- way unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.

Instruments and controls 2-35

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (112,1)

HORN

HEATED SEATS (if so equipped)

WARNING

Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat tempera- tures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in serious injury.

SIC3586

To sound the horn, push the pad area *A of the steering wheel.

WARNING

Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury.

CAUTION

The battery could run down if the seat heater is operated while the engine is not running.

. Do not use the seat heater for extended periods or when no one is using the seat.

. Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.

. Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.

Model "E52-D" EDITED: 2010/ 10/ 25

Turn signals do not work when the hazard warning flasher lights are on.

The flasher can be actuated with the ignition switch in any position.

Some state laws may prohibit the use of the hazard warning flasher switch while driving.

MODELS WITH AUTO LIGHT SYSTEM When an impact that could activate the supple- mental air bags is detected, the hazard warning flasher lights blink automatically. If the hazard warning flasher switch is pushed, the hazard warning flashers will turn off.

WARNING

Do not turn the hazard warning flasher switch to off until you can make sure that it is safe to do so. Also, the hazard flasher warning may not blink automa- tically depending on the force of im- pact.

2-36 Instruments and controls

. Any liquid spilled on the heated seat should be removed immediately with a dry cloth.

. When cleaning the seat, never use gasoline, thinner, or any similar materials.

If any malfunctions are found or the heated seat does not operate, turn the switch off and have the system checked by a NISSAN dealer.

SIC2770

The seats are warmed by built-in heaters. The switches located on the instrument panel can be operated independently of each other.

1. Start the engine.

2. Select heat range.

*1 For high heat, push the HI (High) side of

the switch.

*2 For low heat, push the LO (Low) side of

the switch.

The indicator light in the switch *3 will illuminate when the heater is on.

Black plate (113,1)

3. To turn off the heater, return the switch to the level position. Make sure the indicator light goes off.

The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.

When the vehicle’s interior is warmed, or before you leave the vehicle, be sure to turn off the switch.

Instruments and controls 2-37

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (114,1)

BLIND SPOT WARNING (BSW) SWITCH (if so equipped)

VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH

To cancel the warning systems, push the BSW switch to turn off the system. The BSW ON indicator *1 will turn off. NOTE: If you continue to push the warning systems switch from off to on for over 4
seconds, a chime will sound. This will change the default status of the BSW system to OFF so that this system will not automatically turn on when the engine is started. If this procedure is repeated, the default status will return to ON.

SSD1179

The Blind Spot Warning (BSW) switch will turn on and off the Blind Spot Warning (BSW) system.

The BSW system will illuminate the Blind Spot Warning (BSW) indicator lights, in the outside mirrors, when the radar sensors detect a vehicle in the detection zone. is activated in the direction of the detected vehicle, a chime sounds twice and the BSW indicator light will flash. (See “BLIND SPOT WARNING (BSW) SYSTEM” in the “5. Starting and driving” section.)

the turn signal

If

The BSW switch is automatically turned on when the engine is started, and the BSW ON indicator *1 on the switch illuminates.

2-38 Instruments and controls

SSD1149

The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions.

If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off.

To turn off the VDC system, push the VDC OFF switch. The

indicator will illuminate.

Push the VDC OFF switch again or restart the engine to turn on the system. (See “VEHICLE DYNAMIC CONTROL (VDC) SYSTEM” in the “5. Starting and driving” section.)

Model "E52-D" EDITED: 2010/ 10/ 25

POWER OUTLET

CAUTION

. Use power outlet with the engine running to avoid discharging the vehicle battery.

. Avoid using power outlet when the air conditioner, headlights or rear window defroster is on.

. Before inserting or disconnecting a plug, be sure the electrical acces- sory being used is turned OFF.

. When not in use, be sure to close the cap. Do not allow water to contact the outlet.

Instrument panel

SIC4723

Black plate (115,1)

Type A

To use the power outlet, pull illustrated.

the cover as

CAUTION

The outlet and plug may be hot during or immediately after use.

. Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory.

This power outlet is not designed for use with a cigarette lighter unit. . Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tem- perature fuse may open.

Cargo area

SIC4724

Instruments and controls 2-39

Model "E52-D" EDITED: 2010/ 10/ 25

Black plate (116,1)

exceed a 120 volt, 150W (1.25A) power draw or the power outlet may switch off automatically. If this occurs, turn the main switch on the power outlet off and wait a short period of time before turning it back on again. If an electrical appliance with a wattage of less than 150W is used, the power outlet will be usable again.

. Use this power outlet with the (If the engine is engine running. stopped, this could result in a dis- charged battery.)

. When using the outlet for a long period of time such as when idling etc., the battery may discharge de- pending on the vehicle conditions, even if the engine is running.

. Some electrical appliances with wattages below 150W, may not operate normally. For example:

— Electrical appliances which con- sume a large amount of wattage when turned on (CRT TVs, elec- tric tools etc.)

— Electrical appliances which have a switching power frequency

Model "E52-D" EDITED: 2010/ 10/ 25

Type B (if so equipped)

Main switch

Power outlet Pull up the cover and plug in.

SIC2648

SIC4725

The power outlet (plug type) is located on the front console. It can operate when the ignition switch in the ON position and the main switch (located on the instrument panel) is ON.

The specification of this power outlet is for use of a 120 volt, 150W (1.25A) power draw.

To turn on or off the power supply to the outlet, push the ON *1 or OFF *2
side of the main switch. When the switch is turned to the ON position, the indicator light *A will illuminate.

After using the power outlet, be sure to turn off the main switch.

CAUTION

. Make sure that there is no fluid or other foreign substance in the power outlet. Also, be sure not to connect or disconnect the outlet with wet hands or insert any metal objects into it. Doing so could result in an electric shock or malfunction. . Do not use with accessories that

2-40 Instruments and controls

STORAGE

(clocks etc.)

CUP HOLDERS

— Electrical appliances that mea- sure precise data (measuring equipment etc.)

— Certain other electrical appli-

ances (electric blankets etc.)

. Depending on the electrical appli- ance that is in use, some distorted noise may be audible when using the TV or radio.

. Be sure to turn the power switch of the electrical appliance used off before removing the plug from the power outlet.

. Do not use an extension cord with

multiple outlets.

CAUTION

. Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.

. Use only soft cups in the cup holder. Hard objects can injure you in an accident.

Black plate (117,1)

Instrument panel

SIC4726

Front

Instrument panel:

To open the cup holder, push the instrument panel *1 .

Instruments and controls 2-41