2000 Nissan Pathfinder Owners Manual

The remote controller can operate at a dis- tance of approximately 33 ft (10 m) from the vehicle. (The effective distance depends upon the conditions around the vehicle.) As many as four remote controllers can be used with one vehicle. For information con- cerning the purchase and use of additional remote controllers, contact your NISSAN dealer.

The multi-remote controller will not function when: I the battery is dead, I the distance between the vehicle and the

remote controller is over 33 ft (10 m).

The panic alarm will not activate when the key is in the ignition switch.

CAUTION

The following conditions or occurrences will damage the remote controller.

I Do not allow the remote controller to

become wet.

I Do not drop the remote controller. I Do not strike the remote controller

sharply against another object.

I Do not place the remote controller for an extended period in an area where temperatures exceed 140°F (60°C).

If a multi-remote controller is lost or stolen, NISSAN recommends erasing the ID code of that controller. This will prevent the controller from unautho- rized use to unlock the vehicle. For in- formation regarding the erasing proce- dure, please contact an authorized NISSAN dealer.

HOW TO USE MULTI-REMOTE CONTROL SYSTEM Setting hazard and horn chirp mode This vehicle is set in hazard and horn chirp mode when you first receive the vehicle. In hazard and horn chirp mode, when the LOCK button is pushed, the hazard indicator

flashes twice and the horn chirps once. When the UNLOCK button is pushed, the hazard indicator flashes once. If hazard and horn chirp mode is not neces- sary, you can switch to normal mode by fol- lowing the switching procedure. In normal mode, when the LOCK button is pushed, the hazard indicator flashes twice. When the UNLOCK button is pushed, neither the hazard indicator nor the horn operates. (Switching procedure) Press and hold the LOCK and UNLOCK but- tons on the multi-remote controller simulta- neously for at least 2 seconds to switch from one mode to the other. When pushing the buttons to set normal mode, the hazard indicator flashes 3 times. When pushing the buttons to set hazard and horn chirp mode, the hazard indicator flashes once and the horn chirps once.

Pre-driving checks and adjustments 3-5

Z 00.1.17/R50-D/V5 X

horn chirp mode will not function.

Locking doors 1. Remove the ignition key.*1

2. Close all the doors.*2

3. Push the LOCK button on the multi-remote

controller.

4. All the doors will lock. All of the doors will lock when the LOCK button on the multi-remote controller is pushed even though a door remains open and/or the ignition key is in the ON posi- tion.

3-6 Pre-driving checks and adjustments

SPA0982

5. The hazard indicator flashes twice and the

horn chirps once.

I When the LOCK button is pushed with all doors locked, the hazard indicator flashes twice and the horn chirps once as a re- minder that the doors are already locked.

*1: Doors lock with the remote controller while a key is in the ignition switch. However, the panic alarm will not activate when the ignition switch is in the ACC or ON posi- tion.

*2: Doors lock with the remote controller while any door is open. However, hazard and

Z 00.1.17/R50-D/V5 X

2. Push the UNLOCK button on the multi-

remote controller again within 5 seconds.

I All doors unlock I The hazard indicator flashes once if all

doors are completely closed.

The interior light can be turned off without waiting for 30 seconds by inserting the key into the ignition or by locking the doors with the multi-remote controller. Using the panic alarm If you are near your vehicle and feel threat- ened, you may activate the alarm to call atten- tion as follows: 1. Push the PANIC button on the remote

controller for longer than 0.5 seconds.

2. The theft warning alarm and headlights will

stay on for 30 seconds.

3. The panic alarm stops when: I It has run for 30 seconds, or I The LOCK or

pressed, or

the UNLOCK button is

I The panic button is pushed on the multi-

remote controller.

Pre-driving checks and adjustments 3-7

Unlocking doors 1. Push the UNLOCK button on the multi-

remote controller.

I Only the driver’s door unlocks

SPA0943
I The hazard indicator flashes once if all

doors are completely closed.

I The interior light turns on and the light timer activates for 30 seconds when the switch is in the center q position.

Z 00.1.17/R50-D/V5 X

could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC Rules and RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, in- cluding interference that may cause undes- ired operation of the device.

Recommended battery: Sanyo CR2025 or equivalent

Make sure that the ¯ side faces the bottom case.

3. Close the lid securely.

4. Push the remote controller button two or

three times to check its operation.

See your NISSAN dealer if you need any assistance for replacement. If the battery is removed for any reason other than replacement, perform step 4
above. I Be careful not to touch a circuit board

and a battery terminal.

I An improperly disposed battery can harm the environment. Always confirm local regulations for battery disposal.

I The remote controller is water-proof; however, if it does get wet, immediately wipe completely dry.

I When changing batteries, do not let dust

or oil get on the controller.

FCC Notice: Changes or modifications not expressly approved by the manufacturer compliance

Z 00.1.17/R50-D/V5 X

SPA1046

Battery replacement Replace the battery as follows:

1. Open the lid using a suitable tool.

2. Replace the battery with a new one.

3-8 Pre-driving checks and adjustments

HOOD

REAR DOOR

1. Pull the hood lock release handle located below the instrument panel; the hood will then spring up slightly.

2. Raise the lever at the front of the hood with

your fingertips and raise the hood.

3. Insert the assist bar into the slot in the front

edge of the hood.

4. When closing the hood, reset the assist bar to its original position, then slowly close the hood and make sure it locks into place.

SPA0387

SPA0462

WARNING

WARNING

I Make sure the hood is completely closed and latched before driving. Failure to do so could cause the hood to fly open and result in an accident. I If you see steam or smoke coming to

from the engine compartment, avoid injury do not open the hood.

Do not drive with the rear door open. This could allow dangerous exhaust gases to be drawn into the vehicle. See “Precautions when starting and driving” in the “5. Starting and driving” section for exhaust gas.

KEY OPERATION 1. Turn the key counterclockwise to unlock the

rear door. Pre-driving checks and adjustments 3-9

Z 00.1.17/R50-D/V5 X

Turning the rear door key one time coun- terclockwise will unlock the rear door. From that position, returning the key to neutral (where the key can only the re- moved and inserted.) and turning it coun- terclockwise again within 5 seconds will unlock all doors. 2. Pull the opener handle to open the rear

door.

3. To lock the rear door, push it down firmly

and turn the key clockwise.

The power door lock system allows you to lock or unlock all doors including the rear door simultaneously. I Turning the front door key to the front of

the vehicle will lock all doors.

I Turning the front door key one time to the rear of the vehicle will unlock the corresponding door. From that position, returning the key to neutral (where the key can only be removed and inserted.) and turning it to the rear again within 5
seconds will unlock all doors.

3-10 Pre-driving checks and adjustments

SPARE TIRE CARRIER (if so equipped)

SPA0385

SPA0386

I Before driving, be certain that the spare tire carrier is firmly closed and latched.

I Failure to do so may injure pedestri-

ans or damage the vehicle.

When opening the rear door, first open the spare tire carrier in the sequence shown in the illustration above. Then insert the stopper into the hole to secure the carrier in the open position.

CAUTION

I Be certain that there is adequate area

to allow the carrier to open fully.

I Open and close the spare tire carrier

slowly.

Z 00.1.17/R50-D/V5 X

GLASS HATCH

gases to be drawn into the vehicle. See “Precautions when starting and driving” in the “5. Starting and driving” section for exhaust gas.

CAUTION

Do not open the glass hatch unless the wiper is in the stowed position.

SPA0338C

SPA0956B

KEY OPERATION To open the glass hatch, turn the key fully clockwise and pull the opener handle. To close, lower and push the glass hatch down securely.

Other key operations I Turning the key clockwise locks all doors

including the back door.

I Turning the key counterclockwise unlocks

the rear door.

I Turning the key counterclockwise again

unlock all doors.

WARNING

Do not drive with the glass hatch open. This could allow dangerous exhaust

Pre-driving checks and adjustments 3-11

Z 00.1.17/R50-D/V5 X

FUEL FILLER LID

SPA0341

FUEL FILLER CAP The fuel filler cap is a screw-on ratcheting type. Tighten the cap clockwise until ratcheting clicks are heard.

WARNING

I Gasoline is extremely flammable and highly explosive under certain condi- tions. You could be burned or seri- ously injured if it is misused or mis- handled. Always stop the engine and

SPA0389

OPENER OPERATION To open the fuel filler lid, push the opener lever down. To lock, close the fuel filler lid securely.

3-12 Pre-driving checks and adjustments

do not smoke or allow open flames or sparks near the vehicle when refuel- ing.

I Fuel may be under pressure. Turn the cap one-half turn, and wait for any hissing sound to stop to prevent fuel from spraying out and possible per- sonal injury. Then remove the cap.

I Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel over-flow, resulting in fuel spray and possibly a fire.

I Only use an original equipment type fuel filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system. An in- correct cap can result in a serious malfunction and possible injury or it may cause the MIL to illuminate.

I Never pour fuel into the throttle body

to attempt to start your vehicle.

Z 00.1.17/R50-D/V5 X

CAUTION

I If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.

I Tighten until cap clicks, failure to tighten fuel cap properly may cause the malfunction indicator lamp (MIL) to illuminate. If this occurs, se- curely close the fuel filler cap. After driven for a while, the lamp should turn off. If the lamp remains on, have the vehicle inspected by an autho- rized NISSAN dealer. For additional information, see the “Malfunction indicator lamp (MIL)” in the “2. Instruments and controls” section.

STEERING WHEEL

SPA0342

SPA0394

Put the fuel filler cap on the cap holder while refueling.

TILT OPERATION While pushing down on the lock lever, adjust the steering wheel up or down to the desired position. Push the lock lever up securely to lock the steering wheel in place.

WARNING

Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident.

Pre-driving checks and adjustments 3-13

Z 00.1.17/R50-D/V5 X

SUN VISORS

MIRRORS

USING THE SUN VISORS 1. To block out glare from the front, swing

down the main sun visor.

2. To block glare from the side, remove the main sun visor from the center mount and swing it to the side.

3. Then,

to block glare from the front

swing down the sub-sun visor equipped).

too, (if so

4. To adjust the glare block position, slide the

sub-sun visor to the left.

CAUTION

I Do not store the main sun visor be-

fore storing the sub-sun visor.

I Do not pull the sub-sun visor forcedly

downwards.

PD1006M

INSIDE MIRROR The night position will reduce glare from the headlights of vehicles behind you at night.

WARNING

Use the night position only when neces- sary, because it reduces rear view clar- ity.

3-14 Pre-driving checks and adjustments

SPA0395

Z 00.1.17/R50-D/V5 X

SPA1110

PD1183MB

M008

OUTSIDE MIRRORS The outside mirror will operate only when the ignition switch is in the ACC or ON position. Turn the control knob to the right or left to select then adjust.

the right or left outside mirror,

The outside mirror can be moved in any direc- tion for a better rear view.

Foldable outside mirrors Push the mirror backward to fold it.

WARNING

Objects viewed in the outside mirror on the passenger side are closer than they appear. Be careful when moving to the right. Using only this mirror could cause an accident. Use inside mirror or glance over your shoulder to properly judge distances to other objects.

Pre-driving checks and adjustments 3-15

Z 00.1.17/R50-D/V5 X

MEMO

3-16 Pre-driving checks and adjustments

Z 00.1.17/R50-D/V5 X

4 Heater, air conditioner and audio systems

Ventilators ................................................................. 4-2
Heater and air conditioner (Manual) ......................... 4-3
Controls ..................................................................... 4-3
Heater operation ....................................................... 4-4
Air conditioner operation ........................................... 4-5
Air flow charts ........................................................... 4-6
Heater and air conditioner (Automatic) ..................... 4-9
Automatic operation ................................................ 4-10
Manual operation .................................................... 4-10
Operating tips.......................................................... 4-11

Servicing air conditioner.......................................... 4-11
Audio system........................................................... 4-12
FM radio reception .................................................. 4-12
AM radio reception.................................................. 4-13
FM-AM radio with cassette player .......................... 4-14
FM-AM radio with cassette player and compact disc (CD) player.............................................................. 4-19
Antenna ................................................................... 4-25
CB radio or car phone ............................................ 4-26

Z 00.1.17/R50-D/V5 X

VENTILATORS

Open or close, and adjust the air flow direction of ventilators.

: This symbol indicates that the vents are closed when the vent switch is moved to the left.

: This symbol indicates that the vents are open when the vent switch is moved to the right.

4-2 Heater, air conditioner and audio systems

SAA0159C

Z 00.1.17/R50-D/V5 X

HEATER AND AIR CONDITIONER (Manual)

WARNING

I The air conditioner cooling function operates only when the engine is run- ning.

I Do not

leave children,

impaired adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or injuries to people or possibly fatal

CONTROLS Fan control dial This dial turns the fan on and off, and controls fan speed. Air flow control dial This dial allows you to select outlets.

the air flow

— Air flows from center and side venti-

lators.

— Air flows from center and side venti-

lators and foot outlets.

— Air flows mainly from foot outlets. — Air flows from defroster outlets and

foot outlets.

— Air flows mainly from defroster out-

lets.

Temperature control dial This dial allows you to adjust the temperature of the outlet air.

SAA0152B

animals.

I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full atten- tion may be given to the driving op- eration.

Heater, air conditioner and audio systems 4-3

Z 00.1.17/R50-D/V5 X

Air recirculation button Off position Outside air is drawn into the passenger com- partment. Use the off position for normal heater, or air conditioner operation. On position (Indicator light on) Interior air is recirculated inside the vehicle. Push the air recirculation button to the on position when driving on a dusty road or to avoid traffic fumes. Air conditioner button This button is provided only for vehicles with air conditioner. Start the engine, move the fan control dial to the desired (1 to 4) position and push the air conditioner button to turn on the air condi- tioner. The indicator light will come on when the air conditioner button is on. To stop the air conditioner, push the switch again to return it to the original position. The air conditioner cooling function oper- ates only when the engine is running.

4-4 Heater, air conditioner and audio systems

HEATER OPERATION Heating This mode is used to direct hot air from the floor outlets.

1. Push the air recirculation button to the off

position for normal heating.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Turn the temperature control dial

to the desired position between the middle and the hot position.

I For quick heating, move the air recirculation button to the on position. Be sure to return the air recirculation button to the off position for normal heating.

Ventilation This mode directs outside air from the side and centre vents.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

position.

3. Turn on the fan control dial.

4. Turn the temperature control dial

to the

desired position.

Defrosting or defogging This mode is used to defrost/defog the win- dows.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Turn the temperature control dial

to the desired position between the middle and the hot position.

I To quickly remove ice or fog from the windows, push the air recirculation button to the on position, the fan control dial to 4
and the temperature control dial to the full hot position. As soon as possible after the window is clear, push the air recirculation button to the off position.

Bi-level heating This mode directs outside air from the side and center vents and hot air from the floor outlets. 1. Push the air recirculation button to the off

position.

Z 00.1.17/R50-D/V5 X

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Normally turn the temperature control dial

to the midpoint between hot and cold.

Heating and defogging This mode heats the interior and defogs the windscreen. 1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

tion.

posi-

3. Turn on the fan control dial. 4. Turn the temperature control dial

to the desired position between the middle and the hot position.

Operating tips I Clear snow and ice from the wiper blade and air inlet in front of the windshield. This will improve heater operation.

I A slight delay may be experienced when turning the air control dial. This is not a problem, it is only the system motors and solenoids switching from one outlet to an- other.

AIR CONDITIONER OPERATION Start the engine, move the fan control dial to the desired (1 to 4) position and push in the air conditioner button to activate the air condi- tioner. When the air conditioner is on, cooling and dehumidifying functions will be added to the heater operation. The air conditioner cooling function oper- ates only when the engine is running. Cooling This mode is used to cool and dehumidify. 1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the 3. Turn on the fan control dial. 4. Push on the air conditioner button. The

position.

indicator light will come on.

5. Turn the temperature control dial

desired position.

to the

I For quick cooling when the outside tem- perature is high, push the air recirculation button to the on position. Be sure to return the air recirculation button to the off position for normal cooling.

Dehumidified heating This mode is used to heat and dehumidify.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Push on the air conditioner button. The

indicator light will come on.

5. Turn the temperature control dial

to the

desired position.

Dehumidified defogging This mode is used to defog the windows and dehumidify.

1. Push the air recirculation button to the off

position.

2. Turn the air control dial to the

posi-

tion.

3. Turn on the fan control dial.

4. Push on the air conditioner button. The

indicator light will come on.

5. Turn the temperature control dial

to the

desired position.

Heater, air conditioner and audio systems 4-5

Z 00.1.17/R50-D/V5 X

Operating tips I Keep windows and sun roof closed while

the air conditioner is in operation.

I After parking in the sun, drive for two or three minutes with the windows open to vent hot air from the passenger compart- ment. Then, close the windows. This will allow the air conditioner to cool the interior more quickly.

I The air conditioning system should be operated for about ten minutes at least once a month. This helps prevent dam- age to the system due to lack of lubrica- tion.

I If the coolant temperature gauge exceeds the hot position, turn the air conditioner off. For additional information, see “If your ve- hicle overheats” in the “6. In case of emer- gency” section.

AIR FLOW CHARTS The following charts show the button and dial positions for maximum and quick heating, cooling or defrosting. The air recirculation switch should always be in the off position for heating and defrosting.

4-6 Heater, air conditioner and audio systems

Z 00.1.17/R50-D/V5 X

SAA0154A

SAA0155A Heater, air conditioner and audio systems 4-7

Z 00.1.17/R50-D/V5 X

4-8 Heater, air conditioner and audio systems

SAA0156A

SAA0157A

Z 00.1.17/R50-D/V5 X

HEATER AND AIR CONDITIONER (Automatic)

Start the engine and operate the controls to activate the air conditioner.

WARNING

I The air conditioner cooling function operates only when the engine is run- ning.

I Do not

leave children,

impaired adults, or pets alone in your vehicle. On hot, sunny days, temperatures in a closed vehicle could quickly be- come high enough to cause severe or possibly fatal injuries to people or animals.

I Do not use the recirculation mode for long periods as it may cause the interior air to become stale and the windows to fog up.

I Positioning of the heating or air con- ditioning controls should not be done while driving, in order that full atten- tion may be given to the driving op- eration.

SAA0347

Heater, air conditioner and audio systems 4-9

Z 00.1.17/R50-D/V5 X

AUTOMATIC OPERATION Cooling and/or dehumidified heating (AUTO) This mode may be used all year round. The system works automatically to maintain a constant temperature. Air flow distribution and fan speed are also controlled automatically.

1. Push the AUTO button on. (AUTO will

appear on the display.)

2. Push the temperature control button to set the desired temperature. I For normal operation, adjust the tempera-

ture control button to about 75°F (24°C).

I The temperature of the passenger compart- ment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically.

Heating (ECON) Use this mode when you need to heat only. 1. Push the ECON (Economy) button on.

(ECON appears on the display.)

2. Push the temperature control button to set the desired temperature. I The temperature of the passenger compart- 4-10 Heater, air conditioner and audio systems

ment will be maintained automatically. Air flow distribution and fan speed are also controlled automatically.

I Do not set the temperature lower than the outside air temperature. Otherwise the sys- tem may not work properly.

I If the windows fog up, do not use the ECON

mode.

Dehumidified defogging 1. Push the DEF

switch on. (The indica-

tor light will come on.)

2. Push the temperature control button to set the desired temperature. I To remove ice or fog from the outside of the windows, push the manual fan control but- ton and set to the maximum position. I As soon as possible after the windshield is clean, push the AUTO button to return to the auto mode. I When the DEF

button is pushed, the air conditioner will automatically be turned on at outside temperatures above 28°F (−2°C) to defog the windshield. The air recirculation mode will automatically be turned off.

partment to improve defogging performance. MANUAL OPERATION Fan speed control Push the fan control button the fan speed manually. I Push the AUTO button to return to auto-

to change

matic control of the fan speed.

Air recirculation Push the air recirculation button to recir- culate interior air inside the vehicle. The indi- cator light will come on.

Push it again to draw outside air into the passenger compartment. The indicator will go out. I The air

recirculation button cannot be activated when the air conditioner is in the DEF mode.

Air flow control Pushing the MODE button selects the air outlet to provide:

: Air flow from center and side ventilators.

: Air flow from center and side ventilators

Outside air is drawn into the passenger com-

and foot outlets.

Z 00.1.17/R50-D/V5 X

: Air flow mainly from foot outlets. : Air flow from defroster and foot outlets.

To turn the system off Push the OFF button. OPERATING TIPS I When the engine coolant temperature and outside air temperature are low, the air flow from the foot outlets may not operate for 0
to 126 seconds. This is not a malfunction. After the coolant temperature warms up, air flow from the foot outlets will operate nor- mally.

SAA0158

The sensor on the instrument panel helps maintain a constant temperature. Do not put anything on or around this sensor.

SERVICING AIR CONDITIONER

The air conditioning system in your NISSAN vehicle is charged with a refrigerant designed with the environment in mind. This refrigerant will not harm the earth’s ozone layer. However, special charging equipment and lu- bricant are required when servicing your NISSAN air conditioner. Using improper refrig- erants or lubricants will cause severe damage to your air conditioning system. See “Capaci- ties and recommended fuel/lubricants” in the “10. Technical and consumer information” sec- tion for air conditioning system refrigerant and lubricant recommendation. Your NISSAN dealer will be able to service your environmentally friendly air conditioning system.

WARNING

The air conditioner system contains re- frigerant under high pressure. To avoid personal injury, any air conditioner ser- vice should be done only by an experi- enced technician with proper equip- ment.

Heater, air conditioner and audio systems 4-11

Z 00.1.17/R50-D/V5 X

AUDIO SYSTEM

Turn the ignition key to ACC or ON and press the power on switch to turn on the radio. If you listen to the radio with the engine not running, the key should be turned to the ACC position. Radio reception is affected by station signal strength, distance from radio transmitter, build- ings, bridges, mountains and other external influences. Intermittent changes in reception quality normally are caused by these external influences. Using a cellular phone in or near the ve- hicle may influence radio reception quality. Radio reception Your radio system is equipped with state-of- the-art electronic circuits to enhance radio reception. These circuits are designed to ex- tend reception range, and to enhance the quality of that reception. However there are some general characteris- tics of both FM and AM radio signals that can affect radio reception quality in a moving ve- hicle, even when the finest equipment is used. These characteristics are completely normal in a given reception area, and do not indicate any malfunction in your radio system. Remember that a moving vehicle is not the ideal place to listen to a radio. Because of the movement, reception conditions will constantly 4-12 Heater, air conditioner and audio systems

change. Buildings, terrain, signal distance and interference from other vehicles can work against ideal reception. Described below are some of the factors that can affect your radio reception.

SAA0306

FM RADIO RECEPTION Range: FM range is normally limited to 25 to 30 miles (40 to 48 km), with monaural (single channel) FM having slightly more range than stereo FM. External influences may some- times interfere with FM station reception even if the FM station is within 25 miles (40 km). The strength of the FM signal is directly related to the distance between the transmitter and re- ceiver. FM signals follow a line-of-sight path, exhibiting many of the same characteristics as light. For example they will reflect off objects.

Fade and drift: As your vehicle moves away

Z 00.1.17/R50-D/V5 X

from a station transmitter, the signals will tend to fade and/or drift.

power lines, electric signs and even traffic lights.

Static and flutter: During signal interference from buildings, large hills or due to antenna position, usually in conjunction with increased distance from the station transmitter, static or flutter can be heard. This can be reduced by adjusting the treble control counterclockwise to reduce treble response. Multipath reception: Because of the reflective characteristics of FM signals, direct and re- flected signals reach the receiver at the same time. The signals may cancel each other, resulting in momentary flutter or loss of sound. AM RADIO RECEPTION AM signals, because of their low frequency, can bend around objects and skip along the ground. the signals can be bounced off the ionosphere and bent back to earth. Because of these characteristics. AM signals are also subject to interference as they travel from transmitter to receiver. Fading: Occurs while the vehicle is passing through freeway underpasses or in areas with many tall buildings. It can also occur for sev- eral seconds during ionospheric turbulence even in areas where no obstacles exist. Static: Caused by thunderstorms, electrical

In addition,

Heater, air conditioner and audio systems 4-13

Z 00.1.17/R50-D/V5 X

FM-AM RADIO WITH CASSETTE PLAYER Audio main operation Power/Volume control: Turn the ignition key to ACC or ON, then push the Power/Volume control knob. The mode (radio or cassette) which was playing immedi- ately before the system was turned off re- sumes playing. When no cassette is loaded, the the Power/Volume button again turns the system off. Turn the Power/Volume control knob to adjust the volume.

Pushing

comes

radio

on.

4-14 Heater, air conditioner and audio systems

SAA0348

Z 00.1.17/R50-D/V5 X

display reappears. Once the sound quality is set to the desired level, press the AUDIO button repeatedly until the radio or cassette tape display appears. Clock operation:

Pressing the CLOCK button alternates the clock and the radio/cassette tape options in the display. Radio/Cassette tape priority mode:

In this mode, the radio station illuminates in the display during radio operation. During cassette tape operation, TAPE illuminates in the dis- play. Frequency range and step change operations The frequency range and step of this radio can be changed to the central/south American specification. To change the frequency range and step, proceed as follows:

1. Turn the audio unit on.

2. Press and hold the station select buttons 3

and 4.

3. Press the manual

” while the station select buttons 3 and 4 are being pressed. “MW 530 kHz” is displayed.

tuning button “

The frequency range and step have now been changed to the central/south American speci- fication. FM-AM radio operation FM-AM band select:

Push the FM(cid:215) AM band select button to change from AM to FM reception. The FM stereo indicator, ST illuminates during FM stereo reception. When the stereo broad- cast signal is weak, the radio automatically changes from stereo to monaural reception.

TUNE (Tuning):

WARNING

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

Push either manual

tuning button

or

SEEK/SCAN tuning:

Push the SEEK/SCAN tuning button for less than 1.5 seconds. SEEK tuning begins from low to high frequencies and stops at the next broadcasting station. Pushing the button Heater, air conditioner and audio systems 4-15

Z 00.1.17/R50-D/V5 X

SAA0260

Adjusting tone quality and speaker balance: To adjust BASS(cid:215) TREB(cid:215) FADER(cid:215) BAL (Bass, Treble, Fader, Balance), press the AUDIO button until the desired mode (BAS, TRE, FAD or BAL) appears in the display. Press the button to adjust Bass (BAS) and Treble (TRE) to the desired level. Use the button to adjust Fader or Balance modes. Fader adjusts the sound level between the front and rear speakers and Balance (BAL) adjusts the sound level be- tween the right and left speakers. After 10 seconds, the radio or cassette tape

or

or

again continues the SEEK function. Once the highest broadcasting station is reached, the radio continues in the SEEK mode at the lowest broadcast station. Push the SEEK/SCAN tuning button for more than 1.5 seconds. SCAN illuminates in the display window. SCAN tuning begins from low to high frequencies and stops at each broadcasting station for five seconds. Pushing the button again during this five second period stops SCAN tuning and the radio remains tuned to that station.

select AM, FM1, or FM2. The selected band illuminates in the display.

2. Tune to the desired station. 3. Select the desired station and keep pushing any of the desired station memory buttons (1 to 6) until a peep sound is heard. For example, in the illustrations ch2 is to be memorized. The radio mutes when the se- lect button is pushed.

4. When the sound resumes, memorizing is

complete.

5. Other station select buttons can be set in

the same manner.

If the battery cable is disconnected, or if the radio fuse opens, the radio memory is can- celled. In that case, reset the desired stations. Cassette tape player operation Turn the ignition key to ACC or ON, then carefully insert a cassette tape into the tape door. The cassette tape automatically pulls into the player. The word TAPE and moving digital squares illuminate on the right side of the display window.

SAA0259

Station memory operations:

Six stations can be set for the AM band. 12
stations can be set for the FM band (six for FM1, six for FM2). 1. Push the FM(cid:215) AM band select button to

4-16 Heater, air conditioner and audio systems

Z 00.1.17/R50-D/V5 X

CAUTION

Do not force the cassette tape into the tape door. This could cause player dam- age.

this time,

The cassette tape automatically changes di- rections to play the other side when the first side is complete. At the moving digital squares illuminate on the left side of the display window. Precaution on cassette player operation: I To maintain good quality sound, NISSAN recommends using cassette tapes of 60
minutes or shorter in length.

I Cassette tapes should be removed from the player when not in use. Store cassettes in their protective cases and away from direct sunlight, heat, moisture and magnetic sources.

I Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

I Do not use cassettes with labels which are

peeling and loose. If used, the label could jam in the player.

I If a cassette has loose tape, insert a pencil through one of the cassette hubs and re- wind the tape firmly around the hubs. Loose tape may cause tape jamming and waver- ing sound quality.

I Over a period of time, the playback head, capstan and pinch roller may collect a tape coating residue as the tape is played. This residue accumulation can cause weak or wavering sound, and should be removed periodically with a head cleaning tape. If the residue is not removed periodically, the player may need to be disassembled for cleaning.

PLAY/STOP:

Push the PLAY/STOP button while the cas- sette tape is playing to stop the tape. Push the button again to play the tape.

FF (Fast Forward), REW (Rewind):

Push either the FF or REW button for the desired direction. The FF or REW symbol display. To stop the FF or REW function, press the

illuminates in the

or

again, or the

button.

APS (Automatic Program Search) FF, APS REW:

Push either the APS FF or APS REW button while the cassette tape is playing. The tape runs quickly, stops, then plays the next selec- tion. Either the FF or REW symbol flashes in the display while searching for the selection. This system searches at the blank intervals between selections. If there is a blank interval within one selection or there is no interval between selections, the system may not stop in the desired or expected location.

PROG (Program):

Push the PROG (program) select button. The moving digital squares illuminate on either the right or left side of the display window to indicate the side of program play.

Dolby NR (Noise Reduction):

indicator light comes on.

Push the Dolby NR button for Dolby NR en- coded tapes to reduce high frequency tape noise. The If in the clock display is in priority mode when the Dolby NR button is pressed, and TAPE illuminate in the display window for about 10 seconds. The clock mode then re- Heater, air conditioner and audio systems 4-17

Z 00.1.17/R50-D/V5 X

turns to the display window. Dolby NR is manufactured under license from Dolby Laboratories Licensing Corporation. DOLBY NR and the double-D symbol are trademarks of Dolby Laboratories Licensing Corporation. Metal or chrome tape usage: The cassette player is automatically set to high performance play when playing a metal or chrome cassette tape. TAPE EJECT:

Push the EJECT button. The cassette tape automatically comes out.

4-18 Heater, air conditioner and audio systems

SAA0349

Z 00.1.17/R50-D/V5 X

CD) which was playing immediately before the system was turned off. When no CD or tape is loaded, the radio will come on. While the system is on, pushing the Power/Volume con- trol knob turns the system off. To turn the radio off, press the Power/Volume control knob. Turn the Power/Volume control knob to adjust the volume.

FM-AM RADIO WITH CASSETTE PLAYER AND COMPACT DISC (CD) PLAYER Audio main operation Head unit The tape deck employs a permalloy head which allows for improved reproduction of high frequency ranges. Noise is also greatly re- duced by the combined use of the Dolby NR (Noise Reduction) system. The auto loudness circuit enhances the low frequency range au- tomatically in both radio reception and tape and CD playback. Bose system (if so equipped) A large output amplifier featuring a low distor- tion ratio is connected directly to each speaker unit to provide increased output and excellent tonal quality. The equalizing circuit permits regeneration of forcible base sound. This equalizing circuit permits the sound efficiency to be matched with the interior conditions of your vehicle for a selection between “natural sound” and “high-fidelity sound”. Power/Volume control: Turn the ignition key to ACC or ON, and then push the Power/Volume control knob while the system is off to call up the mode (radio, tape or

Heater, air conditioner and audio systems 4-19

Z 00.1.17/R50-D/V5 X

Clock priority mode In this mode the clock is shown in the display. If any radio, cassette or CD functions are activated, the radio, cassette or CD display illuminates for 10 seconds then returns to the clock mode. NOTE: After clock adjustment, the radio is in the clock priority mode. FM-AM radio operation

FM-AM band select:

Pushing the FM/AM band select button will change the band FM1, FM2 or AM. When FM/AM band select button is pushed while the ignition switch is in the ACC or ON, the radio will come on at the station last played. The last station played will also come on when the power knob is turned to ON. If a compact disc or tape is playing when the FM/AM band select button is turned to ON, the compact disc or tape will automatically be turned off and the last radio station played will come on. The FM stereo indicator ST will glow during FM stereo reception. When the stereo broad-

SAA0305

the AUDIO button repeatedly until the radio or cassette tape display appears. Clock operation: Pressing the clock button alternates the clock and the radio/cassette/CD player options in the display. Adjusting the time Depressing the clock and buttons to- gether sets hours. Depressing the clock and

buttons together sets minutes.

Adjusting tone quality and speaker balance:

(TRE) to the desired level. Use the

To adjust BASS, TRE (Treble), BAL (Balance) and FAD (Fader), press the AUDIO button until the desired mode BAS, TRE, FAD or BAL appears in the display. Press the or button to adjust Bass (BAS) and Treble or button also to adjust Fader (FAD) or Balance (BAL) modes. FAD adjusts the sound level between the front and rear speakers and BAL adjusts the sound between the right and left speakers. After 10 seconds, the radio or cassette tape display reappears. Once the sound quality is set to the desired level, press 4-20 Heater, air conditioner and audio systems

Z 00.1.17/R50-D/V5 X

and the radio will remain tuned to that station. If the SEEK/SCAN tuning button is not pushed within 10 seconds, SCAN tuning moves to the next station.

cast signal is weak, the radio will automatically change from stereo to monaural reception.

TUNE (Tuning):

WARNING

The radio should not be tuned while driving in order that full attention may be given to the driving operation.

Use these buttons for manual tuning. To move quickly through the channels, hold either of the TUNE buttons down for more than 0.5 sec- onds.

SEEK/SCAN tuning:

Push the SEEK/SCAN tuning button

or for less than 1.5 seconds. SEEK tuning begins from high to low or low to high frequen- cies and stops at the next broadcasting sta- tion. Push the SEEK/SCAN tuning button

or for more than 1.5 seconds. SCAN tuning begins from high to low or low to high frequen- cies and stops at each broadcasting station for 10 seconds. Pushing the button again during this 10 seconds period will stop SCAN tuning

SAA0354
Heater, air conditioner and audio systems 4-21

Z 00.1.17/R50-D/V5 X

Station memory operations: Twelve stations can be set for the FM band (six for FM1, six for FM2). Six stations can be set for the AM band. 1. Tune to the desired station using the

SEEK/SCAN or TUNE button.

2. Select the desired station and keep pushing any of the desired station memory buttons (1 to 6) until a peep sound is heard. (For example, in the diagram ch2 is to be memo- rized. The radio mutes when the select button is pushed.)

3. The indicator ch2 will then come on and the sound will resume. Memorizing is now com- plete.

4. Other buttons can be set

manner.

in the same

If the battery cable is disconnected, or if the fuse blows, the radio memory will be can- celled. In that case, reset the desired stations. Cassette tape player operation Turn the ignition key to ACC or ON, and then lightly insert the cassette tape into the tape door. The cassette tape will be automatically pulled into the player. The radio or CD will turn off (if it is on) and the 4-22 Heater, air conditioner and audio systems

cassette tape will begin to play.

CAUTION

Do not force the cassette tape into the tape door. This could cause player dam- age.

If the system is turned off by pushing the ON(cid:215) OFF/VOL control knob with the cassette tape still in the player, the tape will resume playing when the system is turned back on. Precautions on cassette tape player operation: I To maintain good quality

sound, NISSAN recommends that you use cas- sette tapes of 60 minutes or shorter in length.

I Cassette tapes should be removed from the player when not in use. Store cas- settes in their protective cases and away from direct sunlight, heat, dust, mois- ture or magnetic sources. Direct sunlight can cause the cassette to become deformed. The use of deformed cassettes may cause the cassette to jam in the player.

I Do not use cassettes that have peeling or loose labels. If used, the label could jam in the player.

I If a cassette has loose tape,

insert a pencil through one of the cassette hubs and rewind the tape firmly. Loose tape may cause jamming and wavering sound quality.

I Over a period of

time,

the playback head, capstan and pinch roller may gather a tape coating residue as the tape passes over the head. This residue ac- cumulation can cause a weak or waver- ing sound and should be removed peri- odically with a head cleaning tape. If the residue is not removed periodi- cally, the player may need to be disas- sembled for cleaning.

PLAY:

I When the TAPE button is pushed with the system turned off and a tape loaded, the system will come on and the tape will play. I When the TAPE button is pushed with either the radio or compact disc turned on and the tape loaded, the compact disc or the radio will automatically be turned off and the tape will play.

Z 00.1.17/R50-D/V5 X

FF (Fast Forward), REW (Rewind):

(fast forward) button to fast Push the forward the tape. To rewind the tape, push the (rewind) button. Either the FF or REW symbol the display window. To stop the FF or REW func- tion, press the (re- wind) again, or the TAPE button.

illuminates on the right side of

(fast forward) or

APS (Automatic Program Search) FF, APS REW:

When the (APS FF) button is pushed while the tape is being played, the next pro- gram will start to play from the beginning. Push the (APS FF) button several times to skip through programs. The tape will advance the number of times the button is pushed (up to nine programs). When the (APS REW) button is pushed once, the program being played starts over from the beginning. Push the (APS REW) button several times to skip back sev- eral selections. The tape will go back the number of times the button is pushed. Either the FF or REW symbol flashes on the right side of the display window while searching for the selection. This system searches for the blank intervals

between selections. If there is a blank interval within one program or there is no interval between programs, the system may not stop in the desired or expected location.

When the tape is ejected while it played, the system will be turned off. Compact Disc (CD) player operation

is being

PROG (Program):

Push the PROG button to change the tape side while the tape is being played. The cassette tape will automatically change directions to play the other side when the first side is completed.

Dolby NR (Noise Reduction):

Push the Dolby NR button for Dolby NR encoded tapes to reduce high frequency tape noise. The indicator will come on. Dolby noise reduction manufactured under li- cense from Dolby Laboratories Licensing Cor- poration. Dolby NR and the double-D symbol are trademarks of Dolby Laboratories

Licensing Corporation. Metal or chrome tape usage: The cassette player will be automatically set to high performance play when playing a metal or chrome cassette tape. TAPE EJECT:

When this button is pushed with the tape loaded, the tape will be ejected.

CAUTION

I During cold weather or rainy days, the player may malfunction due to the humidity. If this occurs, remove the CD and dehumidify or ventilate the player completely.

I The player may skip while driving on

rough roads.

I The CD player sometimes cannot function when the compartment tem- perature is extremely high. Decrease the temperature before use.

I Do not expose the CD to direct sun-

light.

I CDs that are of poor quality, dirty, scratched, or covered with finger- prints may not work properly.

I Do not use an 8 cm CD adapter as this

will cause malfunction.

Heater, air conditioner and audio systems 4-23

Z 00.1.17/R50-D/V5 X

I Recordable compact discs (CD-R) may not function properly in the CD player.

Turn the ignition key to the ACC or ON position and insert the compact disc into the slot with the label side facing up. The compact disc will be guided automatically into the slot and start playing. After loading the disc, the number of tracks on the disc and the play time will appear on the display. If the radio or tape is already operating, it will automatically turn off and the compact disc will play.

CAUTION

Do not force the compact disc into the slot. This could damage the player.

If the system has been turned off while the compact disc was playing, pushing the ON(cid:215) OFF/VOL control knob will start the com- pact disc. 8 cm diameter compact discs can also be used without an adapter. 4-24 Heater, air conditioner and audio systems

PLAY:

When the CD/CHG button is pushed with the system off and the compact disc loaded, the system will turn on and the compact disc will start to play.

When the CD/CHG button is pushed with the compact disc loaded but the tape or the radio playing, the tape or radio will automatically be turned off and the compact disc will start to play.

FF (Fast Forward), REW (Rewind): (fast forward) or

When the (rewind) button is pushed while the compact disc is being played, the compact disc will play while fast forwarding or rewinding. When the button is released, the compact disc will return to normal play speed.

APS (Automatic Program Search) FF, APS REW: When the (APS FF) button is pushed while the compact disc is being played, the program next to the present one will start to play from its beginning. Push several times to skip through programs. The compact disc will advance the number of times the button is pushed. (When the last program on the com- pact disc is skipped through, the first program

(APS REW) will be played.) When the button is pushed, the program being played returns to its beginning. Push several times to skip back through programs. The compact disc will go back the number of times the button is pushed.

PROG (Program):

When the PROG button is pushed while the compact disc is being played, the play pattern will change as follows:

no mark: All repeatedly in sequence.

the programs will be played

1: Only one program (the one being played when the PROG button is pushed) will be repeated.

RANDOM: Programs will be played at random, not following the sequence on the compact disc. The same program may be repeated twice. When the compact disc is ejected, the play pattern will automatically change to no mark.

CD EJECT:

When the CD EJECT button is pushed with the compact disc loaded, the compact disc will be ejected.

Z 00.1.17/R50-D/V5 X

When this button is pushed while the compact disc is being played, the compact disc will come out and the system will turn off. If the compact disc comes out and is not removed, it will be pulled back into the slot to protect it. (without 8 cm diameter com- pact discs) CD IN indicator: CD IN indicator appears on the display when the CD is loaded with the system on.

antenna rod cannot be hand tightened to the proper specification.

CAUTION

I Always properly tighten the antenna rod during installation or the antenna rod may bend or break during vehicle operation.

I To prevent damage, be sure that manual antenna is removed before the vehicle enters an automated car wash.

Power antenna The antenna will automatically extend when the radio is turned on, and retract when switched off. If the radio is left on, the antenna will retract and extend with the ignition key OFF-ON operation.

CAUTION

I Before turning the radio on, make sure that there is no one near the

SAA0164

ANTENNA Manual antenna The manual antenna on your vehicle remains in the upper position at all times. The antenna cannot be shortened, but can be removed. When you need to remove the antenna, turn the antenna nut counterclockwise. To install the antenna rod, turn the antenna nut clock- wise. Tighten the antenna rod to specification using a suitable tool, such as an open-end wrench. The antenna rod tightening specifica- tion is 3.4 to 3.6 N(cid:215) m (30 to 32 in-lb). Do not use pliers to tighten the antenna as they can leave marks on the antenna surface. The

Heater, air conditioner and audio systems 4-25

Z 00.1.17/R50-D/V5 X

antenna outlet and there is enough space for it to extend.

I To prevent damage, be sure that power antenna is fully retracted be- fore the vehicle enters an automated car wash.

I Dirt and other foreign matter on the power antenna rod may interrupt its operation. Clean the rod periodically with a damp cloth. This type of clean- ing is especially important during the winter seasons in areas where road salt and other chemicals may be spread surfaces and splashed onto the antenna rod.

road

on

I Adjust the antenna standing-wave ra- tio as recommended by the manufac- turer.

I Connect the ground wire from the CB

radio chassis to the body.

I For details, consult an authorized

NISSAN dealer.

CB RADIO OR CAR PHONE

If equipped with a genuine NISSAN cellular phone, your NISSAN features a non- directional microphone in the steering column cover, so it is not necessary to look at or speak directly into the microphone when calling. To do so could detract from the driving operation and cause an accident. See the car phone manual for operation. Some models are pre-wired to accept the genuine NISSAN cellular phone. In addition, the same model has the phone antenna built into the rear glass window. When installing a CB, ham radio or car phone in your NISSAN, be sure to observe the follow- ing cautions, otherwise the new equipment may adversely affect the Engine control sys- tem and other electronic parts.

CAUTION

I Keep the antenna as far as possible away from the Engine Control Module (ECM).

I Keep the antenna wire more than 8 in (20 cm) away from the Multiport Fuel Injection harness. Do not route the antenna wire next to any harness.

4-26 Heater, air conditioner and audio systems

Z 00.1.17/R50-D/V5 X

5 Starting and driving

Precautions when starting and driving...................... 5-2
Exhaust gas (Carbon monoxide) .............................. 5-2
Three way catalyst .................................................... 5-3
On-pavement and offroad driving precautions.......... 5-3
Avoiding collision and rollover................................... 5-4
Drinking alcohol/drugs and driving............................ 5-4
Driving safety precautions......................................... 5-4
Ignition switch............................................................ 5-6
Automatic transmission ............................................. 5-6
Manual transmission ................................................. 5-7
Key positions............................................................. 5-8
Nissan vehicle immobilizer system ........................... 5-8
Before starting the engine......................................... 5-9
Starting the engine.................................................... 5-9
Driving the vehicle................................................... 5-10
Automatic transmission ........................................... 5-10
Manual transmission ............................................... 5-14
Parking brake .......................................................... 5-16
Cruise control (if so equipped)................................ 5-17
Precautions on cruise control.................................. 5-17

Cruise control operations ........................................ 5-18
Break-in schedule ................................................... 5-19
Increasing fuel economy ......................................... 5-20
Using four wheel drive (4WD)................................. 5-20
Transfer case shifting procedures........................... 5-22
Parking/parking on hills........................................... 5-24
Power steering ........................................................ 5-25
Brake system .......................................................... 5-26
Braking precautions ................................................ 5-26
Anti-lock brake system (ABS) ................................. 5-26
Cold weather driving ............................................... 5-28
Freeing a frozen door lock...................................... 5-28
Anti-freeze ............................................................... 5-28
Battery ..................................................................... 5-28
Draining of coolant water ........................................ 5-28
Tire equipment ........................................................ 5-28
Special winter equipment........................................ 5-29
Driving on snow or ice ............................................ 5-29
Engine block heater (if so equipped) ...................... 5-29

Z 00.1.17/R50-D/V5 X

PRECAUTIONS WHEN STARTING AND DRIVING

WARNING

I Do not

leave children,

impaired adults, or pets alone in your vehicle. They could accidentally injure them- selves or others through inadvertent operation of the vehicle. Also, on hot, sunny days, temperatures in a closed vehicle could quickly become high enough to cause severe or possibly fatal injuries to people or animals.

I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.

EXHAUST GAS (Carbon monoxide)

WARNING

Do not breathe exhaust gases; they con- tain colorless and odorless carbon mon- oxide. Carbon monoxide is a dangerous. It can cause unconsciousness or death. I If you suspect that exhaust fumes are entering the vehicle, drive with all windows fully open, and have the vehicle inspected immediately.

I Do not run the engine in closed

spaces such as a garage.

I Do not park the vehicle with the en- gine running for any extended length of time.

I Keep the back door and glass hatch closed while driving, otherwise ex- haust gases could be drawn into the passenger compartment. If you must drive with the back door on glass hatch open, follow these precautions:

1. Open all the windows.

2. Set

the air recirculation switch OFF and the fan control at 4 (high) to circulate the air.

I If electrical wiring or other cable con- nections must pass to a trailer through the seal on the back door or the body, follow the manufacturer’s recommendation to prevent carbon monoxide entry into the vehicle.

I If a special body or other equipment is added for recreational or other us- age, follow the manufacturer’s rec- ommendation to prevent carbon monoxide entry into the vehicle. (Some recreational vehicle appli- ances such as stoves, refrigerator, heaters, etc. may also generate car- bon monoxide.)

I The exhaust system and body should be inspected by a qualified mechanic whenever:

a. The vehicle is raised for service.

b. You suspect that exhaust fumes are entering into the passenger

5-2 Starting and driving

Z 00.1.17/R50-D/V5 X

compartment.

c. You notice a change in the sound

of the exhaust system.

d. You have had an accident involv- ing damage to the exhaust system, underbody, or rear of the vehicle.

THREE WAY CATALYST The three way catalyst is an emission control device, installed in the exhaust system. In the converter, exhaust gases are burned at high temperatures to help reduce pollutants.

WARNING

I The exhaust gas and the exhaust sys- tem are very hot. Keep people, ani- mals or flammable materials away from the exhaust system compo- nents.

I Do not stop or park the vehicle over flammable materials, such as dry grass, waste paper or rags. They may ignite and cause a fire.

CAUTION

I Do not push or tow your vehicle to

start the engine.

I Do not use leaded gasoline. Deposits from leaded gasoline seriously re- duce the three way catalyst’s ability to help reduce exhaust pollutants.

I Keep your engine tuned up. Malfunc- tions in the ignition, fuel injection, or electrical systems can cause over- rich fuel flow into the three way cata- lyst, causing it to overheat. Do not keep driving if the engine misfires, or if noticeable loss of performance or other unusual operating conditions are detected. Have the vehicle in- spected promptly by an authorized NISSAN dealer.

I Avoid driving with an extremely low fuel level. Running out of fuel could cause the engine to misfire, damag- ing the three way catalyst.

I Do not race the engine while warming

it up.

ON-PAVEMENT AND OFFROAD DRIVING PRECAUTIONS Utility vehicles have a significantly higher rollover rate than other types of vehicles. They have higher ground clearance than pas- senger cars to make them capable of perform- ing in a variety of on-pavement and offroad applications. This gives them a higher center of gravity than ordinary cars. An advantage of higher ground clearance is a better view of the road, allowing you to anticipate problems. However, they are not designed for cornering at the same speeds as conventional two-wheel drive vehicles any more than low-slung sports cars are designed to perform satisfactorily under offroad conditions. If at all possible, avoid sharp turns or abrupt maneuvers, par- ticularly at high speeds. As with other vehicles of failure to operate this vehicle correctly may result in loss of control or vehicle rollover. Be sure to read the driving safety precautions later in this section.

this type,

Starting and driving 5-3

Z 00.1.17/R50-D/V5 X

AVOIDING COLLISION AND