Outside mirror remote control (P.3-15)
Cruise control set switch (P.5-17)
Windshield and rear window wiper/ washer switch (P.2-16)
Compass/outside air temperature display (P.2-6)
Hazard warning flasher switch (P.2-21)
Passenger supplemental air bag (P.1-10)
Center ventilator (P.4-2)
Heater/air conditioner control (P.4-3)
Side ventilator (P.4-2)
Instrument brightness control (P.2-18)
Security indicator light (P.2-14)
Fuse box cover (P.8-22)/Tray (P.2-24)
Hood release handle (P.3-9)
Tilting steering wheel adjust lever (P.3-13)
2-2 Instruments and controls
Ignition switch/steering lock (P.5-6)
Glove box (P.2-26)
Cigarette lighter (P.2-23)
Heated seat switch (P.2-22)
Radio/CD player (P.4-19)/clock (P.4-15)
Glass hatch/outside mirror defogger switch (P.2-17)
See the page indicated in parentheses for operating details.
SIC1327
Z 00.1.17/R50-D/V5 X
METERS AND GAUGES
SIC0857
SIC0858
SPEEDOMETER AND ODOMETER Speedometer The speedometer indicates vehicle speed. Odometer/twin trip odometer The odometer/twin trip odometer are displayed when the ignition key is in the ON position. The odometer records the total distance the vehicle has been driven. The twin trip odometer records the distance of individual trips.
Instruments and controls 2-3
Z 00.1.17/R50-D/V5 X
SIC0754A
SIC0859
SIC0545
Changing the display: Push the reset knob to change the display as follows: ODO , TRIP A , TRIP B , ODO Resetting the trip odometer: Push the reset knob for more than 1 second to reset the trip odometer to zero.
TACHOMETER The tachometer indicates engine speed in revolutions per minute (r/min).
CAUTION
When engine speed approaches the red zone, shift to a higher gear. Operating the engine in the red zone may cause serious engine damage.
ENGINE COOLANT TEMPERATURE GAUGE The gauge indicates the engine coolant tem- perature. The engine coolant temperature will vary with the outside air temperature and driving condi- tions.
CAUTION
If the gauge indicates engine coolant temperature over the normal range, stop
2-4 Instruments and controls
Z 00.1.17/R50-D/V5 X
the vehicle as soon as safely possible. If the engine is overheated, continued op- eration of the vehicle may seriously damage the engine. See “If your vehicle overheats” in the “6. In case of emer- gency” section for immediate action re- quired.
convenient, preferably before the gauge reaches E. There will be a small reserve of fuel in the tank when the fuel gauge needle reaches E.
CAUTION
If the vehicle is driven with the fuel level very low, the malfunction indicator lamp may come on. Refuel as soon as pos- sible. After driving for a while, the lamp should go off. If the lamp remains on, have the vehicle inspected by an autho- rized NISSAN dealer. For additional information, see the “Mal- function indicator lamp (MIL)” later in this section.
SIC0960
FUEL GAUGE The gauge indicates the APPROXIMATE fuel level in the tank.
The gauge may move slightly during braking, turning, acceleration, or going up or down hill.
The gauge needle is designed to remain in approximately the same position, even when the ignition key is turned OFF. Refill the fuel tank before the gauge regis- ters Empty. The indicator light comes on when the fuel tank is getting low. Refuel as soon as it is
Instruments and controls 2-5
Z 00.1.17/R50-D/V5 X
COMPASS AND OUTSIDE TEMPERATURE DISPLAY (if so equipped)
SIC0590
SIC0610
This unit is a display unit with the following functions: I Function to measure terrestrial magnetism
and indicate heading direction of vehicle
I Function to indicate outside air temperature I Function to indicate caution for frozen road
surfaces
OUTSIDE TEMPERATURE DISPLAY Push the switch when the ignition key is in the ACC or ON position. The outside temperature will be displayed in °F. I Selecting the indication range
Push the switch to change from °F to °C. I If the outside temperature drops below the
freezing point, the display indicates ICE.
I When the outside temperature is be- tween 130°F (55°C) and 158°F (70°C), the display shows 130°F (55°C).
I When the outside temperature is lower than −20°F (−30°C) or higher than 158°F (70°C), the display shows only - - - though it is operating. This is not a problem.
CAUTION
I The outside temperature sensor is located in front of the radiator. The display may not indicate the precise temperature due to road and engine heat, wind direction and other driving conditions.
I Use the ICE indication for reference only. Confirm the traffic information and road conditions to drive safely.
2-6 Instruments and controls
Z 00.1.17/R50-D/V5 X
COMPASS DISPLAY Push the switch when the ignition key is in the ACC or ON position. The direction will be displayed. Zone variation change procedure The difference between magnetic north and geographical north is known as variance. In some areas, this difference can sometimes be great enough to cause false compass read- ings. Follow these instructions to set the vari- ance for your particular location if this hap- pens: 1. Establish your location on the zone map.
Record your zone number.
2. Push the ON/OFF switch in for five seconds until the current zone entry number is dis- played.
3. Press the ON/OFF switch repeatedly until
the new zone entry number is displayed.
Once the desired zone number is displayed, stop pressing the ON/OFF switch and the display will show compass direction within a few seconds.
SIC0611
Instruments and controls 2-7
Z 00.1.17/R50-D/V5 X
CAUTION
In places where the earth’s magnetism is disturbed, the initial correction proce- dure may start automatically.
I If a magnet is located near the compass or the vehicle is driven where the terres- trial magnetism is disturbed, the com- pass display may not indicate the cor- rect direction.
I In places where the terrestrial magne- tism is disturbed, the correction of the direction starts automatically, extin- guishing the direction bar. If turn is made one or two times, the correction is complete and the direction bar comes back on.
Correction functions of the compass display The compass display is equipped with auto- matic correction function. If the direction is not shown correctly, carry out manual correction procedure set out below. Manual correction procedure 1. Push the switch for about 10 seconds. The
direction bar starts blinking.
2. Drive the vehicle slowly in an open and safe area. The initial correction is completed while turning one or two turns.
2-8 Instruments and controls
Z 00.1.17/R50-D/V5 X
WARNING/INDICATOR LIGHTS AND CHIMES
Anti-lock brake warning light (Except for Canada) Anti-lock brake warning light (For Canada) Automatic transmission oil temperature warning light
Door open warning light
Cruise indicator light
Engine oil pressure warning light
4WD indicator light
Low washer fluid warning light (Canada only)
High beam indicator light
Automatic transmission park warning light
Seat belt warning light and chime
Malfunction indicator lamp (MIL)
or
Brake warning light
Supplemental air bag warning light
Overdrive off indicator light (Automatic transmission models only)
Charge warning light
Tire carrier open warning light
Turn signal/hazard indicator lights
CHECKING BULBS Apply the parking brake and turn the ignition key to ON without starting the engine. The following lights will come on:
or
The following lights come on briefly and then go off:
or
If any light fails to come on, it may indicate a burned-out bulb or an open circuit in the elec- trical system. Have the system repaired promptly.
WARNING LIGHTS
or
Anti-lock brake warning light
If the light comes on while the engine is running, it may indicate there is something wrong with the anti-lock brake system. Have the system checked by your NISSAN dealer.
If an abnormality occurs in the system, the anti-lock function will cease but the ordinary brakes will continue to operate normally. If the light comes on while you are driving, contact your NISSAN dealer for repair.
Automatic transmission oil temperature warning light
model)
This light comes on when the automatic trans- mission oil temperature is too high. If the light comes on while driving, reduce the vehicle speed as soon as safely possible until the light turns off.
CAUTION
Continued vehicle operation when the A/T oil temperature warning light is on
Instruments and controls 2-9
Z 00.1.17/R50-D/V5 X
may damage the automatic trans- mission.
Automatic transmission park warning light (
model)
This light indicates that the automatic trans- mission parking function is not engaged. If the transfer control is not secured in any drive position while the automatic transmission se- lector lever is in the P (Park) position, the transmission will disengage and the wheel will not lock.
Shift the transfer control lever into the 2H or 4L position when the warning light comes on.
WARNING
I When parking, always make sure that the transfer lever is in H or 4L and the parking brake is set.
I If the ATP light is ON, this indicates that the automatic transmission P (Park) position will not function and the transfer lever is in neutral.
2-10 Instruments and controls
I Failure to engage the transfer control lever in H or 4L could result in the vehicle moving unexpectedly, result- ing in serious personal injury or prop- erty damage.
or
Brake warning light This light functions for both the parking brake and the foot brake systems. Parking brake indicator: The light comes on when the parking brake is applied. Low brake fluid warning light: When the ignition key is in the ON position, the light warns of a low brake fluid level. If the light comes on while the engine is running, stop the vehicle and perform the following: 1. Check the brake fluid level. Add brake fluid as necessary. See “Brake and clutch fluid” in the “8. Do-it-yourself” section. 2. If the brake fluid level is correct: Have the warning system checked by a NISSAN dealer.
WARNING
I Your brake system may not be work- ing properly if the warning light is on. Driving could be dangerous. If you judge it to be safe, drive carefully to the nearest service station for re- pairs. Otherwise, have your vehicle towed.
I Pressing the brake pedal with the engine stopped and/or low brake fluid level may increase your stopping dis- tance and braking will require greater pedal effort as well as greater pedal travel.
I If the brake fluid level is below the MIN mark on the brake fluid reservoir, do not drive until the brake system has been checked at a NISSAN dealer.
Charge warning light
If the light comes on while the engine is running, it may indicate that there is something wrong with the charging system. Turn the
Z 00.1.17/R50-D/V5 X
engine off and check the alternator belt. If the belt is loose, broken, missing or if the light remains on, see your NISSAN dealer immedi- ately.
CAUTION
Do not continue driving if the belt is loose, broken or missing.
Door open warning light
This light comes on when any of the doors and/or rear window are not closed securely while the ignition key is ON.
Engine oil pressure warning light
This light warns of low engine oil pressure. If the light flickers or comes on during normal driving, pull off the road in a safe area, stop the engine immediately and call a NISSAN dealer or other authorized repair shop. The oil pressure warning light is not de- signed to indicate a low oil level. Use the dipstick to check the oil level. See “Engine oil” in the “8. Do-it-yourself” section.
CAUTION
Running the engine with the oil pressure warning light on could cause serious damage to the engine almost immedi- ately. Turn off the engine as soon as it is safe to do so.
Low washer fluid warning light (Canada only)
This light comes on when the washer fluid in the washer tank is at a low level. Add washer fluid as necessary. See “Window washer fluid” in the “8. Do-it-yourself” section.
Seat belt warning light and chime
The light and chime remind you to fasten seat belts. The light illuminates whenever the igni- tion key is turned to ON, and will remain illuminated until the driver’s seat belt is fas- tened. At the same time, the chime will sound for about six seconds unless the driver’s seat belt is securely fastened. See “Seat belts” in the “1. Seats, restraints and supplemental air bag systems” section for pre-
cautions on seat belt usage.
Supplemental air bag warning light
After turning the ignition key to the ON posi- tion, the supplemental air bag light will illumi- nate. The supplemental air bag warning light will turn off after about 7 seconds if the supple- mental front air bag and supplemental side air bag systems are operational. If any of the following conditions occur, the supplemental air bag needs servicing and your vehicle must be taken to your nearest autho- rized NISSAN dealer. I The supplemental air bag light does not come on and remain on for 7 seconds and then go off as described above.
I The supplemental air bag light flashes in- termittently or remains on. (after 7 seconds) I The supplemental air bag light does not
come on at all.
Unless checked and repaired, the supplemen- tal restraint system may not function properly. For additional information, see “Supplemental restraint system” in the “1. Seats, restraints and supplemental air bag systems” section.
Instruments and controls 2-11
Z 00.1.17/R50-D/V5 X
WARNING
If the supplemental air bag warning light is on, it could mean that the supplemen- tal front air bag system or supplemental side air bag system (if so equipped) will not operate in an accident.
Tire carrier open warning light (if so equipped)
This light comes on when the tire carrier is not closed securely while the ignition key is ON. INDICATOR LIGHTS
Cruise indicator light lamp (if so equipped)
The light comes on while the vehicle speed is controlled by the cruise control system.
If the light flickers while the engine is running, it may indicate there is something wrong with the cruise control system. Have the system checked by your NISSAN dealer. 4WD indicator light
This light comes on when the transfer shift 2-12 Instruments and controls
control lever is in the 4H or 4L position. High beam indicator light
This light comes on when the headlight high beam is on, and goes out when the low beams are selected.
Malfunction indicator lamp (MIL)
If the Malfunction indicator lamp comes on steady or blinks while the engine is running, it may indicate a potential emission control prob- lem. The Malfunction indicator lamp may also come on steady or blink if the fuel filler cap has not been closed tightly or if the fuel tank is nearly empty. Check to make sure the fuel cap is secure and that you have at least 3 US gallons (14 liters) of fuel in the fuel tank. After driving for a while, the lamp should remain off if no other potential emission control system problem exists. Operation The Malfunction indicator lamp will come on in one of two ways: I Malfunction indicator lamp on steady — An emission control system malfunction has been detected. Have the vehicle inspected
by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.
I Malfunction indicator lamp blinking — An engine misfire has been detected which may damage the emission control system. To reduce or avoid emission control system damage:
* do not drive at speeds above 45 MPH (72
km/h).
* avoid hard acceleration or deceleration. * avoid steep uphill grades. * if possible, reduce the amount of cargo
being hauled or towed.
The malfunction indicator lamp may stop blink- ing and come on steady.
Have the vehicle inspected by an authorized NISSAN dealer. You do not need to have your vehicle towed to the dealer.
CAUTION
Continued vehicle operation without having the emission control system checked and repaired as necessary could lead to poor driveability, reduced
Z 00.1.17/R50-D/V5 X
fuel economy, and possible damage to the emission control system.
Turn signal/hazard indicator lights
if the warning sound is heard when the vehicle is moving, whether or not the brake pedal is depressed.
Overdrive off indicator light (Automatic transmission models only)
This light comes on during driving when the overdrive switch is pressed to prevent over- drive operation.
The O/D OFF indicator light comes on for two seconds each time the ignition key is turned ON. This shows the light is functioning prop- erly. If the O/D OFF indicator light blinks for approximately 8 seconds after coming on for 2 seconds, have your NISSAN dealer check the transmission and repair it if necessary. The automatic transmission is equipped with an electronic Fail-Safe mode. This system allows the vehicle to be driven even in the event of damage to the electrical circuits. If this occurs, the gears automatically engage and lock into 3rd gear. See “Driving the vehicle” in the “5. Starting and driving” section for failsafe before vis- iting your NISSAN dealer.
The light flashes when the turn signal switch lever or hazard switch is turned on. CHIMES Key reminder chimes The chime will sound when the driver side door is opened if the key is left in the ignition switch. Take the ignition key when you leave the vehicle. Light reminder chimes A chime will sound if the driver’s door is opened with the light switch on unless the ignition key is in the ON position. Turn the light switch off when you leave the vehicle. A chime will sound when the light switch is in the ON position and the driver’s door is opened after the light switch has been turned to the OFF position when the light has already turned off automatically. Brake pad wear warning The disc brake pads have audible wear warn- ings. When a brake pad requires replacement, it will make a high pitched scraping sound. Have the brakes checked as soon as possible
Instruments and controls 2-13
Z 00.1.17/R50-D/V5 X
SECURITY SYSTEMS
IC0005
SIC0603
Your vehicle may have two types of security system, as follows: I Theft warning (if so equipped) I Nissan Vehicle Immobilizer System The security condition will be shown by the security indicator light. THEFT WARNING (if so equipped) The theft warning system provides visual and audio alarm signals if parts of the vehicle are disturbed.
the security
Security indicator light This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates systems equipped on the vehicle are operational. How to activate the theft warning system 1. Close all windows. The system can be activated even if the windows are open.
2. Remove the key from the ignition switch.
2-14 Instruments and controls
3. Close and lock all doors, hood, back door and glass hatch. All doors can be locked either with the multi-remote controller, a key, the door lock knob or the lock-unlock switch. See “Doors” in the “3. Pre-driving checks and adjustments” section for locking all doors simultaneously.
4. Confirm that the SECURITY indicator light comes on. The SECURITY light glows for about 30 seconds and then begins to flash. The system is now activated. If, during this 30 second time period, the door is unlocked by the key or multi-remote controller, or the ignition key is turned to ACC or ON, the system will not activate.
Theft warning system operation The warning system will give the following alarm: I The headlights blink and the horn sounds
intermittently.
I The alarm automatically turns off after 2 to 3 minutes; however, the alarm will reacti- vate if the vehicle is tampered with again.
The alarm is activated by: I Unlocking the door, back door or back door glass hatch without using the key or multi- remote controller. is
the door
(Even if
Z 00.1.17/R50-D/V5 X
opened by releasing the door inside lock knob, the alarm is activated.) I Opening the hood. (Even if
the hood is opened by the hood release handle, the alarm is activated.)
I Opening the back door glass hatch. (Even if the back door glass hatch is opened by the opener switch, the alarm is activated.)
I Connecting the battery connector after it has been disconnected from the battery for more than 1 second. How to stop alarm The alarm will stop only by unlocking a door or back door with the key or multi-remote control- ler. The alarm will not stop if the ignition switch is turned to ACC. If the system does not operate as de- scribed above, have it checked by your NISSAN dealer. NISSAN VEHICLE IMMOBILIZER SYSTEM The Nissan Vehicle Immobilizer System will not allow the engine to start without the use of the registered Nissan Vehicle Immobilizer Sys- tem key. If the engine fails to start using the registered
Nissan Vehicle Immobilizer System key (for example, when interference is caused by an- other Nissan Vehicle Immobilizer System key, an automated toll road device or automated payment device on the key ring), restart the engine using the following procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK position, and wait approximately 5 seconds.
3. Repeat step 1 and 2.
4. Restart the engine while holding the device (which may have caused the interference) separate from the registered Nissan Ve- hicle Immobilizer System key.
If the no start condition re-occurs, NISSAN recommends placing the registered Nissan Vehicle Immobilizer System key on a separate key ring to avoid interference from other de- vices. Statement related to section 15 of FCC rules for Nissan Vehicle Immobilizer Sys- tem (CONT ASSY - IMMOBILIZER) This device complies with part 15 of the FCC Rules and RSS-210 of Industry
Canada. Operation is subject to the follow- ing two conditions; (1) This device may not cause harmful interference, and (2) this device must ac- cept any interference received, including interference that may cause undesired op- eration of the device. CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE MANUFAC- TURE RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. Security indicator light This light blinks whenever the ignition switch is in the LOCK, OFF or ACC position. This function indicates systems equipped on the vehicle are operational. If the Nissan Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition key is in the ON position. If the light still remains on and/or the en- gine will not start, see your NISSAN dealer for Nissan Vehicle Immobilizer System ser- vice as soon as possible. Please bring all Nissan Vehicle Immobilizer System keys that you have when visiting your NISSAN dealer for service.
the security
Instruments and controls 2-15
Z 00.1.17/R50-D/V5 X
WINDSHIELD WIPER AND WASHER SWITCH
REAR WINDOW WIPER AND WASHER SWITCH
CAUTION
The following could damage the washer system: I Do not operate the washer continu-
ously for more than 30 seconds.
I Do not operate the washer if the res-
ervoir tank is empty.
SIC1185
WARNING
The windshield wiper and washer operates
when the ignition key is in the ACC or ON
position.
Push the lever down to operate the wiper.
Intermittent operation can be adjusted from 4
to 12 seconds by turning the knob.
Pull
toward you to operate the
washer. Then the wiper will also operate sev-
eral times.
the lever
In freezing temperatures the washer so- lution may freeze on the windshield and obscure your vision which may lead to an accident. Warm the windshield with the defroster before you wash the wind- shield.
SIC0511
The rear window wiper and washer operates when the ignition switch is in the ACC or ON position. Turn the switch clockwise to the intermittent, low speed position to operate the wiper or washer. Turn the switch counterclockwise to the position to operate the washer. Then the
wiper will also operate several times.
2-16 Instruments and controls
Z 00.1.17/R50-D/V5 X
CAUTION
I Do not operate the washer continu-
ously for more than 30 seconds.
I Do not operate the washer if reservoir
tank is empty.
I The rear window wiper will not operate
when the glass hatch is open. The rear window wiper will not operate if the glass hatch is closed with the wiper switch on. To operate the window wiper, turn the switch to off and then to on.
I The glass hatch will not open while the
rear window wiper is operating.
WARNING
In freezing temperatures the washer so- lution may freeze on the glass hatch and obscure your vision. Warm the glass hatch with the defroster before you wash the glass hatch.
GLASS HATCH AND OUTSIDE MIRROR (if so equipped) DEFOGGER SWITCH
HEADLIGHT AND TURN SIGNAL SWITCH
SIC0593
To defog the glass hatch and the outside door
mirrors, start the engine and push the switch
on. (The indicator light will come on.) Push the
switch again to turn the defogger off.
It will automatically turn off in approximately 15
minutes. If the window clears before this time,
push the switch off manually.
CAUTION
When cleaning the inner side of the glass hatch, be careful not to scratch or damage the glass hatch defogger.
SIC1068
HEADLIGHT SWITCH Lighting Turn the switch to the
position:
The side combination, tail, license plate and
Instruments and controls 2-17
Z 00.1.17/R50-D/V5 X
instrument lights will come on.
Turn the switch to the
position:
Headlights will come on and all the other lights remain on. Battery saver system I When the headlight switch is in the
or
position while the ignition switch is in
the ON position, the lights (including the
front fog light) will automatically turn off 45
seconds after the ignition switch has been
turned to the OFF position.
I When you open either the driver’s or front passenger’s door, the lights turn off within the 45 seconds.
automatically. Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, otherwise the battery will go dead.
I Never leave the light switch on when the engine is not running for ex- tended periods of time.
or
I When the headlight switch remains in the position after the lights auto- matically turn off, turn on when the ignition switch is turned to the ON position from the OFF position.
the lights will
CAUTION
I When you turn on the headlight switch after the lights automatically turn off, the lights will not turn off
2-18 Instruments and controls
SIC0052
Instrument brightness control The instrument brightness control operates when the light switch is in the or
position.
Turn the control to adjust the brightness of instrument panel lights and power window switch lights. When the control is turned to the right until a click sound is heard, the light intensity will be at maximum. When the control is turned to the left until a click sound is heard, the light will be turned off.
Z 00.1.17/R50-D/V5 X
WARNING
When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
Passing signal Pulling the lever toward you will turn on the passing signal even when the headlight switch is off. Daytime running light system (Canada only) The headlights automatically illuminate at a reduced intensity when the engine is started with the parking brake released. The daytime running lights operate with the headlight switch in the off position or in the position. Turn the headlight switch to the position for full illumination when driving at night. If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illu- minate once the parking brake is released. The daytime running lights will remain on until the ignition switch is turned off.
Instruments and controls 2-19
Z 00.1.17/R50-D/V5 X
SIC1069
Headlight beam select To select the high beam, push the lever for- ward. Pull it back to select the low beam.
FOG LIGHT SWITCH (if so equipped)
Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flash- ing.
SIC1070
TURN SIGNAL SWITCH Turn signal Move the lever up or down to signal to the turning direction. When the turn is completed, the turn signals cancel automatically. 2-20 Instruments and controls
IC1292
FRONT FOG LIGHT SWITCH To turn the fog lights on, turn the headlight switch to the then turn the switch to the position. To turn them off, turn the switch to the OFF position. The headlights must be on for the fog lights to operate.
position,
Z 00.1.17/R50-D/V5 X
HAZARD WARNING FLASHER SWITCH
HORN
ers while moving on the highway un- less unusual circumstances force you to drive so slowly that your ve- hicle might become a hazard to other traffic.
I Turn signals do not work when the hazard warning flasher lights are on.
The flasher can be actuated with the ignition switch either off or on.
SIC0594
Push the switch on to warn other drivers when you must stop or park under emergency con- ditions. All turn signal lights will flash. Some state laws may prohibit the use of the hazard warning flasher switch while driv- ing.
WARNING
I If stopping for an emergency, be sure to move the vehicle well off the road. I Do not use the hazard warning flash-
To sound the horn, push the center pad area of the steering wheel.
SIC0861
Instruments and controls 2-21
Z 00.1.17/R50-D/V5 X
HEATED SEATS (if so equipped)
SIC0684
The front seat(s) are warmed by built-in heat- ers. The switches located on the instrument panel can be operated independently of each other.
1. Start the engine. The battery could run down if the heater is operated while the engine is not running.
2. Push the
(Low) or
(High) po- sition of the switch, as desired, depending on the temperature. The indicator light in the switch will illuminate. The heater is controlled by a thermostat, automatically turning the heater on and off.
I When cleaning the seat, never use gasoline, thinner, or any similar ma- terials.
I If any abnormalities are found or the heating seat does not operate, turn the switch off and have the system checked by your NISSAN dealer.
The indicator light will remain on as long as the switch is on.
3. When the vehicle’s interior is warmed or before you leave the vehicle, be sure to turn the switch off.
CAUTION
I The battery could run down if the seat heater is operated while the engine is not running.
I Do not use the seat heater for ex- tended periods or when no one is using the seat.
I Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.
I Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.
I Any liquid spilled on the heating seat should be removed immediately with a dry cloth.
2-22 Instruments and controls
Z 00.1.17/R50-D/V5 X
POWER OUTLET
CIGARETTE LIGHTER AND ASHTRAY (Accessory)
draw. Do not use double adapters or more than one electrical accessory. I Use this power outlet with the engine running. (If the engine is stopped, this could result in a discharged bat- tery.)
I Avoid using when the air conditioner, headlights or rear window defogger is on.
I Before inserting or disconnecting a plug, be sure to turn off the power switch of electrical accessory being used or the ACC power of the vehicle. I Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tempera- ture fuse may blow.
I When not in use, be sure to close the cap. Do not allow water to contact the socket.
The power outlet accessories such as cellular telephones.
is for powering electrical
SIC1313
CAUTION
I Use caution as the outlet and plug may be hot during or immediately after use.
I This power outlet is not designed for
use with a cigarette lighter unit.
I Do not use with accessories that ex- ceed a 12 volt, 120W (10A) power
SIC0685A
Instruments and controls 2-23
Z 00.1.17/R50-D/V5 X
STORAGE
The cigarette lighter element is an accessory. A genuine NISSAN cigarette lighter unit can be purchased from your local NISSAN dealer. The cigarette lighter operates when the igni- tion switch is in ACC or ON. Push the lighter in all the way. When the lighter is heated, it will spring out. Return the lighter to its original position after use.
WARNING
The cigarette lighter should not be used while driving in order that full attention may be given to the driving operation.
TRAY
CAUTION
The cigarette lighter socket is a power source for the cigarette lighter element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.
2-24 Instruments and controls
SIC0596
SIC0557
GLASSES CASE The glasses case can be opened by pushing the button.
WARNING
The storage tray should not be used while driving in order that full attention may be given to the driving operation.
Do not place valuable items in the tray.
WARNING
The glasses case should not be used while driving in order that full attention may be given to the driving operation.
Z 00.1.17/R50-D/V5 X
CAUTION
I Do not use for anything other than
glasses.
I Do not leave glasses in the glasses case while parking in direct sunlight. The heat may damage the glasses.
when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your pas- senger.
I Use only soft cups in the cup holder. Hard objects can injure you in an accident.
SIC0553A
CUP HOLDERS
WARNING
The cup holders should not be used while driving in order that full attention may be given to the driving operation.
CAUTION
I Avoid abrupt starting and braking
Instruments and controls 2-25
Z 00.1.17/R50-D/V5 X
To open, push the cup holder. To close, fully push the cup holder.
SIC0698
SPA0388
GLOVE BOX When locking or unlocking the glove box, use the master key. The glove box may be opened by the handle.
WARNING
Keep glove box lid closed while driving to help prevent injury in an accident or during a sudden stop.
2-26 Instruments and controls
SIC1179
Z 00.1.17/R50-D/V5 X
CONSOLE BOX
WARNING
I The center console box should not be used while driving in order that full attention may be given to the driving operation.
I Keep the center console box lid closed while driving to prevent injury in an accident or sudden stop.
Do not place valuable items in the center console box.
WARNING
Keep luggage side console box lids closed securely while driving to prevent injury in an accident or sudden stop.
Do not place valuable items in the luggage side console box.
SIC0598
Instruments and controls 2-27
Z 00.1.17/R50-D/V5 X
I Do not drive with the board removed. I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.
I Never allow anyone to ride in the luggage area or on the rear seat when it is in the fold-down position.
I It is extremely dangerous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
I Do not allow people to ride in any is not
area of your vehicle that equipped with seats and seat belts.
LUGGAGE HOOKS The luggage hooks can be used to secure cargo with ropes or other types of straps.
WARNING
I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.
I Use the suitable ropes and hooks to
secure cargo.
I Never allow anyone to ride in the luggage area. It is extremely danger- ous to ride in a cargo area inside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed.
I Do not allow people to ride in any is not
area of your vehicle that equipped with seats and seat belts. I Be sure everyone in your vehicle is in a seat and using a seat belt properly.
Z 00.1.17/R50-D/V5 X
SPA0346A
CAUTION
I Make sure the luggage board closes
securely.
2-28 Instruments and controls
SPA0408A
SPA0365
Side finisher I When hooking on ropes, do not apply a load of more than 22 lb (98 N) to a single hook.
I Do not use the luggage net between the
A and B hooks.
Floor hooks
Instruments and controls 2-29
Z 00.1.17/R50-D/V5 X
CARGO NET (if so equipped) The cargo net keeps packages in the cargo area from moving around while your vehicle is driven. To install the cargo net, attach the four hooks to the four retainers. To remove the cargo net, detach the four hooks from the cargo net retainers.
2-30 Instruments and controls
SPA0396A
SPA0419
WARNING
I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.
I Be sure to secure all four hooks into
the retainers. The cargo restrained in
the net must not exceed 30 lbs. (13.6
kg) or the net may not stay secured.
TONNEAU COVER (if so equipped) The tonneau cover keeps the luggage com- partment contents hidden from the outside.
To open the tonneau cover, pull it out and hang both sides on the hooks. To close the tonneau cover, remove it from the hooks and release it.
WARNING
I Never put anything on the tonneau cover, no matter how small. Any ob-
Z 00.1.17/R50-D/V5 X
ject on it could cause an injury in an accident or sudden stop.
I Do not leave the tonneau cover in the vehicle with it disengaged from the holder.
I Properly secure all cargo to help pre- vent it from sliding or shifting. Do not place cargo higher than the seat- backs. In a sudden stop or collision, unsecured cargo could cause per- sonal injury.
LUGGAGE RACK (if so equipped) The cross-bars can be adjusted forward and backward. Place your luggage between the bars (A), adjust the bars (A), and secure the luggage with rope to the bars (A). There are also adjustable loops on the side bars for the rope attachment.
Always evenly distribute the luggage on the luggage rack. Do not load more than 100 lb (45 kg). Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the Safety Compliance
SPA0397
Certification Label (located on the driver’s door pillar). For more information regarding GVWR and GAWR, refer to “10. Technical and cus- tomer information”.
CAUTION
Use care when placing or removing items from the luggage rack. If you can- not comfortably lift the items onto the luggage rack from the ground, use a ladder or stool.
Instruments and controls 2-31
Z 00.1.17/R50-D/V5 X
WINDOWS
POWER WINDOWS (if so equipped)
SIC0929
WARNING
I Make sure that all passengers have inside the vehicle their hands, etc. before closing the windows. Use the window lock switch to prevent unex- pected use of the power windows.
I Do not leave children unattended in- side the vehicle. They could unknow-
2-32 Instruments and controls
ingly activate switches or controls and become trapped in a window. Unattended children could become involved in serious accidents.
The power window only operates when the ignition key is in the ON position. To open or close the window, push down or pull up the switch and hold it. The main switch (driver side switches) will open or close all the windows. The power windows are operational for about 45 seconds, even after the ignition key is turned to the OFF position. If the driver’s door or the front passenger’s door is opened during this period of about 45 seconds, power to the windows is canceled.
SIC0627B
The passenger side switch will open or close only the corresponding window. To open or close the window, hold the switch down or up. Locking passenger’s windows When the lock button is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.
Z 00.1.17/R50-D/V5 X
SUNROOF (if so equipped)
SIC1186A
SIC0560
Automatic operation To fully open the driver side window, com- pletely push down the switch and release it; it need not be held. The window will automati- cally open all the way. To stop the window, just pull up the switch toward the close side. A light press on the switch will cause the window to open until the switch is released.
AUTOMATIC SUNROOF The sunroof will only operate when the ignition key is in the ON position. The automatic sunroof is operational for about 45 seconds, even if the ignition key is turned to the OFF position. If the driver’s door or the front passenger’s door is opened during this period of about 45 seconds, power to the sunroof is canceled.
SIC0561
Sliding the sunroof To open the roof, press and hold the switch to the
side.
To close the roof, press and hold the switch to the
side.
Instruments and controls 2-33
Z 00.1.17/R50-D/V5 X
Tilting the sunroof To tilt up, first close the sunroof, then press and hold the To tilt down the sunroof, press and hold the
side of the tilt switch.
side of the tilt switch.
Sun shade Open/close the sun shade by sliding it backward/forward. The shade will open automatically when the sunroof is opened. However, it must be closed manually.
WARNING
I In an accident you could be thrown from the vehicle through an open sunroof. Always use seat belts and child restraints.
I Do not allow anyone to stand up or extend any portion of their body out of the opening while the vehicle is in motion or while the sunroof is clos- ing.
2-34 Instruments and controls
INTERIOR LIGHTS
CAUTION
I Remove water drops, snow,
ice or sand from the sunroof before open- ing.
I Do not place any heavy object on the
sunroof or surrounding area.
If the sunroof does not close Have your NISSAN dealer check and repair the sunroof.
SIC0564A
The lights have a three-position switch. When the switch is in the center q position, the lights will illuminate when a door or the back door is opened.
Z 00.1.17/R50-D/V5 X
The ceiling light will stay on for about 30
seconds when:
I The driver’s door is unlocked by the multi-
remote controller or a key when all doors
are locked.
I The driver’s door is unlocked while the key
is removed from the ignition switch.
I The key is removed from the ignition switch and the driver’s door is opened and then closed.
I The key is removed from the ignition switch
while all doors are closed.
The light will turn off while the 30 second timer is activated when: I The driver’s door is locked either with the multi-remote controller, a key, the door lock knob or the lock-unlock switch.
I The ignition switch is turned ON. When the interior light or the personal light switch is in the ON position, the interior, personal, and vanity mirror lights will auto- matically turn off 10 minutes after the igni- tion switch has been turned to the OFF position. To turn on the light again, insert the key into the ignition switch and move it to the ON position.
After the above procedure, the interior, per- sonal, or vanity mirror lights will automatically turn off 10 minutes after the latest operation of the following: I Opening or closing any door I Locking or unlocking the driver’s door I Inserting or removing a key from the ignition
switch
These lights will turn on again when any of the above operations is performed after the lights have turned off automatically. (The lights will turn off 10 minutes after the latest operation of the above as well.)
CAUTION
I Turn off the interior, personal and vanity mirror lights when you leave the vehicle.
I Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
PERSONAL LIGHTS
SIC0565
When the interior light or the personal light switch is in the ON position, the interior, personal, and vanity mirror lights will auto- matically turn off 10 minutes after the igni- tion switch has been turned to the OFF position. To turn on the light again, insert the key into the ignition switch and move it to the ON position. After the above procedure, the interior, per- sonal, or vanity mirror lights will automatically turn off 10 minutes after the latest operation of the following: I Opening or closing any door I Locking or unlocking the driver’s door
Instruments and controls 2-35
Z 00.1.17/R50-D/V5 X
I Inserting or removing a key from the ignition
switch
These lights will turn on again when any of the above operations is performed after the lights have turned off automatically. (The lights will turn off 10 minutes after the latest operation of the above as well.)
CAUTION
I Turn off the interior, personal and vanity mirror lights when you leave the vehicle.
I Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
VANITY MIRROR LIGHT (if so equipped)
The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.
SIC0186
INTEGRATED HomeLink UNIVERSAL TRANSCEIVER (if so equipped) The Integrated HomeLink Universal Trans- ceiver provides a convenient way to consoli- date the functions of up to three individual hand-held transmitters into one built-in device. Integrated HomeLink Universal Transceiver: I Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.
I Is powered by your vehicle’s battery. No separate batteries are required. If the vehi- cle’s battery is discharged or is discon- nected, HomeLink will retain all program- ming.
is programmed,
Once the Integrated HomeLink Universal Transceiver retain the original transmitter for future programming procedures (i.e., new vehicle purchases). Upon sale of the vehicle, the programmed Integrated HomeLink Universal Trans- ceiver buttons should be erased for secu- rity purposes. For additional information, refer to “Programming the Integrated HomeLink Universal Transceiver” later in this section.
2-36 Instruments and controls
Z 00.1.17/R50-D/V5 X
WARNING
tegrated HomeLink Universal Trans- ceiver.
became
effective
I Do not use the Integrated HomeLink Universal Transceiver with any ga- rage door opener that lacks safety stop and reverse features as required by federal safety standards. (These standards for opener models manufactured after April 1, 1982.) A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.
I During programming, your garage door or gate may open or close. Make sure that people and objects are clear of the garage door or gate that you are programming.
I Your vehicle’s engine should be turned off while programming the In-
SPA0609A
PROGRAMMING HomeLink 1. With the ignition key in the OFF position, press and hold the two outside buttons, and release when the indicator light begins to flash (approximately 20 seconds). This pro- cedure erases the factory set default codes and does not have to be followed when programming additional hand-held trans- mitters.
2. Hold the end of the hand-held transmitter (from the device you wish to train) approxi- mately 2 to 5 inches (50 to 127 mm) away from the surface of HomeLink keeping the indicator light in view.
Instruments and controls 2-37
Z 00.1.17/R50-D/V5 X
3. Using both hands, simultaneously push the hand-held transmitter button and the de- sired HomeLink button. Do not release the buttons until step 4 has been completed. NOTE: Some garage door openers may require the procedures noted under “Canadian Programming”. 4. The HomeLink
flash, first slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing light indicates the Integrated HomeLink Univer- sal Transceiver has been successfully pro- grammed.
indicator light will
To program the remaining two buttons, follow steps 2 through 4. If, after repeated attempts, you do not suc- cessfully program the Integrated HomeLink Universal Transceiver to learn the signal of the hand-held transmitter, refer to “Rolling Code Programming” later in this section. PROGRAMMING HomeLink FOR CANADIAN CUSTOMERS Prior regulations required hand-held transmitters to stop transmitting af- ter 2 seconds. To program your hand-held 2-38 Instruments and controls
to 1992, D.O.C.
transmitter to HomeLink , continue to press
and hold the HomeLink button (note steps 2
through 4 under “Programming HomeLink ”)
while you press and re-press (“cycle”) your
hand-held transmitter every 2 seconds until
the indicator light flashes rapidly (indicating
successful programming).
NOTE:
If programming a garage door opener, etc.,
it is advised to unplug the device during
the “cycling” process to prevent possible
damage to the garage door opener compo-
nents.
OPERATING THE INTEGRATED
HomeLink UNIVERSAL
TRANSCEIVER
The Integrated HomeLink Universal Trans-
ceiver (once programmed) may now be used
to activate the garage door, etc. To operate,
simply press the appropriate programmed In-
tegrated HomeLink Universal Transceiver
button. The red indicator light will
illuminate
while the signal is being transmitted.
PROGRAMMING
PROBLEM-DIAGNOSIS
If the HomeLink does not quickly learn the
hand-held transmitter information:
I replace the hand-held transmitter batteries
with new batteries.
I position the hand-held transmitter with its from the
facing
away
battery HomeLink surface.
area
I press and hold both the HomeLink and hand-held transmitter buttons without inter- ruption.
I position the hand-held transmitter 2 to 5
inches (50 to 127 mm) away from the
HomeLink surface. Hold the transmitter in
that position for up to 15 seconds.
If
HomeLink is not programmed within that
time, try holding the transmitter in another
position - keeping the indicator light in view
at all times.
If you continue to have programming difficul- ties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this Owner’s Manual. CLEARING THE PROGRAMMED INFORMATION Individual buttons cannot be cleared, however to clear all programming, press and hold the two outside buttons and release when the
Z 00.1.17/R50-D/V5 X
indicator light begins to flash (approximately 20 seconds). ROLLING CODE PROGRAMMING Rolling code garage door openers (or other rolling code devices) which are “code pro- tected” and manufactured after 1996, may be determined by the following.
A. Reference the garage door opener Owner’s
Manual for verification.
B. The hand-held transmitter appears to pro- gram the Integrated HomeLink Universal Transceiver but does not activate the ga- rage door.
If
C. Press and hold the trained HomeLink but- ton. the garage door opener has the rolling code feature, the HomeLink indica- tor light will flash rapidly, then remains on after 2 seconds.
To program the Integrated HomeLink Univer- sal Transceiver to a garage door opener with the rolling code feature, follow these instruc- tions after completing the “Programming HomeLink ” (the aid of a second person may make the following procedures quicker and easier). 1. Locate the training button on the garage door opener motor unit. Exact location and
color of the button may vary by garage door opener brand. If there is difficulty locating the training button, reference the garage door opener Owner’s Manual.
2. Press the training button on the garage door opener motor unit (which may activate a training light). NOTE: Following step 2, there are 30 seconds in which to initiate step 3.
3. Firmly press and release the programmed HomeLink button. Press and release the HomeLink button a second time to com- plete the training process. (Some garage door openers may require you to do this procedure a third time to complete the training.)
The garage door opener should now recognize the Integrated HomeLink Universal Trans- ceiver and activate when the HomeLink but- ton is pressed. The remaining two buttons may now be programmed (if not yet programmed, follow steps 2 through 4 in the “Programming HomeLink ” procedures earlier in this section). REPROGRAMMING A SINGLE HomeLink BUTTON To reprogram an Integrated HomeLink Uni-
versal Transceiver button, complete the follow- ing.
1. Press and hold the desired HomeLink button. Do not release the button until step 4 has been completed.
2. When the indicator light begins to flash slowly (after 20 seconds), position the hand-held transmitter 2 to 5 inches (50 to 127 mm) away from the HomeLink sur- face.
3. Press and hold the hand-held transmitter
button.
4. The HomeLink
indicator light will
flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, re- lease both buttons.
The Integrated HomeLink Universal Trans-
ceiver button has now been reprogrammed.
The new device can be activated by pushing
the HomeLink
button that was just pro-
grammed. This procedure will not affect any
other programmed HomeLink buttons.
IF YOUR VEHICLE IS STOLEN
If your vehicle is stolen, you should change the
codes of any non-rolling code device that has
been programmed into HomeLink . Consult
the Owner’s Manual of each device or call the
Instruments and controls 2-39
Z 00.1.17/R50-D/V5 X
manufacturer or dealer of those devices for
additional information.
When your vehicle is recovered, you will
reprogram the
need
to
Integrated
HomeLink
Universal Transceiver with
your new transmitter information.
FCC Notice:
This device complies with FCC rules part
15. Operation is subject to the following
two conditions: (1) This device may not
cause harmful
interference and (2) This
device must accept any interference that
may be received,
including interference
that may cause undesired operation.
The transmitter has been tested and com-
plies with FCC and DOC/MDC rules.
Changes or modifications not expressly
approved by the party responsible for com-
pliance could void the user’s authority to
operate the device.
DOC: ISTC 1763K1313
FCC I.D.: CB2V67690
2-40 Instruments and controls
Z 00.1.17/R50-D/V5 X
3 Pre-driving checks and adjustments
Keys .......................................................................... 3-2
Doors......................................................................... 3-2
Locking with key........................................................ 3-3
Locking with inside lock knob ................................... 3-3
Locking with power door lock switch (if so
equipped) .................................................................. 3-4
Child safety rear door lock........................................ 3-4
Multi-remote control system (if so equipped)............ 3-5
How to use multi-remote control system .................. 3-5
Hood.......................................................................... 3-9
Rear door .................................................................. 3-9
Key operation ............................................................ 3-9
Spare tire carrier (if so equipped) ........................... 3-10
Glass hatch ............................................................. 3-11
Key operation .......................................................... 3-11
Fuel filler lid............................................................. 3-12
Opener operation .................................................... 3-12
Fuel filler cap........................................................... 3-12
Steering wheel ........................................................ 3-13
Tilt operation ........................................................... 3-13
Sun visors ............................................................... 3-14
Using the sun visors ............................................... 3-14
Mirrors ..................................................................... 3-14
Inside mirror ............................................................ 3-14
Outside mirrors........................................................ 3-15
Z 00.1.17/R50-D/V5 X
KEYS
DOORS
A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by your NISSAN dealer. Nissan Vehicle Immobilizer System keys: The key number is necessary when you need extra Nissan Vehicle Immobilizer System keys. As many as 5 Nissan Vehicle Immobi- lizer System keys can be used with one ve- hicle. New keys must be registered to the Nissan Vehicle Immobilizer System compo- nents in your vehicle by your NISSAN dealer. At this time, you should bring all Nissan Ve- hicle Immobilizer System keys that you have to your NISSAN dealer for registration. This is because the registration process will erase all memory of the Nissan Vehicle Immobilizer System components.
WARNING
I Always have the doors locked while driving. Along with the use of seat belts, this provides greater safety in the event of an accident by helping to prevent persons from being thrown from the vehicle. This also helps keep children and others from unintention- ally opening the doors, and will help keep out intruders.
I Before opening any door, always look
for and avoid oncoming traffic.
I Do not leave children unattended in- side the vehicle. They could unknow- ingly activate switches or controls. Unattended children could become involved in serious accidents.
Z 00.1.17/R50-D/V5 X
SPA0942
You can only drive your vehicle using the master keys which are registered to the Nissan Vehicle Immobilizer System components in your vehicle. These keys have a transponder chip in the key head.
The keys can be used for the door, back door or glove box locks. Never leave these keys in the vehicle. Record the key number on the key number plate supplied with your keys and keep it in a safe place (such as your wallet), not in the vehicle. NISSAN does not record any key number so it is very important to keep track of your key number plate. 3-2 Pre-driving checks and adjustments
I Turning the front door key one time to the rear of the vehicle will unlock the corre- sponding door. From that position, return- ing the key to neutral (where the key can only be removed and inserted.) and turning it to the rear again within 5 seconds will unlock all doors.
SPA0383
LOCKING WITH KEY Manual To lock the door, turn the key towards the front of the vehicle. To unlock, turn it towards the rear. Power The power door lock system allows you to lock or unlock all doors including the back door simultaneously. I Turning the front door key to the front of the
vehicle will lock all doors.
PD1160M
LOCKING WITH INSIDE LOCK KNOB Pushing or pulling the door inside lock knob to the lock or unlock will lock or unlock the corresponding door. To lock from the outside without a key, move the inside lock knob to the LOCK position. Then close the door. When locking the door this way, be certain not to leave the key inside the vehicle.
Pre-driving checks and adjustments 3-3
Z 00.1.17/R50-D/V5 X
doors will lock once and then unlock automati- cally.
SPA0944
LOCKING WITH POWER DOOR LOCK SWITCH (if so equipped) Operating the lock-unlock switch will lock or unlock all doors including the back door simul- taneously.
All door locks will be engaged when the power door lock switch is moved to the LOCK posi- tion with the driver’s or front passenger’s door open. Then close the door and all doors will be locked.
When the power door lock switch is moved to the LOCK position while any front doors is open and a key is in the ignition switch, all 3-4 Pre-driving checks and adjustments
SPA0841
CHILD SAFETY REAR DOOR LOCK Child safety locking helps prevent doors from being opened accidentally, especially when small children are in the vehicle. When the lever is in the lock position, the rear door can be opened only from the outside.
Z 00.1.17/R50-D/V5 X
MULTI-REMOTE CONTROL SYSTEM (if so equipped) It is possible to lock/unlock all doors and activate the panic alarm by using the remote controller from outside the vehicle. Before locking the doors, make sure the key is not left in the vehicle.