the dial effects
— The indicator needles sweep in the meters and the ring illumination will be brightened gradually when the engine is started.
To return to the top page of the setting mode, select “BACK”.
SKIP:
Push the warning check mode.
switch *A
to move to the
switch *B to select other menus.
Push the
DETAIL:
This item is available only when a warning is displayed.
Select this menu to see the details of warnings.
SIC3679
Warning check To see if there are any of the following warnings and corresponding details, select this menu. . No key warning
Low fuel warning
Low washer fluid warning
. Parking brake release warning . Door/lift gate open warning . Check tire pressure warning
Loose fuel cap warning
Instruments and controls 2-25
Model "Z51-D" EDITED: 2010/ 9/ 28
vibration occurs.
The system helps deter vehicle theft but cannot prevent it, nor can it prevent the theft of interior or exterior vehicle components in all situations. Always secure your vehicle even if parking for a brief period. Never leave your keys in the vehicle, and always lock it when unattended. Be aware of your surroundings, and park in secure, well-lit areas whenever possible.
Many devices offering additional protection, such as component locks, identification markers, and tracking systems, are available at auto supply stores and specialty shops. Your NISSAN dealer may also offer such equipment. Check with your insurance company to see if you may be eligible for discounts for various theft protection features.
SECURITY SYSTEMS
SIC2133
Your vehicle has two types of security systems, as follows: . Vehicle security system (if so equipped) . NISSAN Vehicle Immobilizer System
The security condition will be shown by the security indicator light.
VEHICLE SECURITY SYSTEM (if so equipped) The vehicle security system provides visual and audio alarm signals if someone opens the doors or lift gate when the system is armed. It is not, however, a motion detection type system that activates when a vehicle is moved or when a
2-26 Instruments and controls
Black plate (98,1)
SIC1699A
How to arm the vehicle security system 1. Close all windows.
The system can be armed even if the windows are open.
2. Push the ignition switch to the OFF position.
3. Carry the Intelligent Key.
4. Close all doors, hood and lift gate. Lock all
doors. The doors can be locked with:
on the Intelligent
the lock button Key
any request switch
the power door lock switch
Model "Z51-D" EDITED: 2010/ 7/ 23
.
the key — master or mechanical
5. Confirm that the security indicator light *A comes on. The security indicator light stays on for about 30 seconds. The vehicle security system is now pre-armed. After about 30 seconds the vehicle security system automatically shifts into the armed phase. The security light begins to flash once every approximately 3 seconds. If, during this 30-second pre-arm time period, the door is unlocked, or the ignition switch is pushed to ACC or ON, the system will not arm.
Even when the driver and/or passengers are in the vehicle, the system will activate with all doors, hood and lift gate locked with the ignition switch in the LOCK position. When pushing the ignition switch to the ACC or ON position, the system will be released.
Vehicle security system activation The vehicle security system will give the follow- ing alarm:
The headlights blink and the horn sounds intermittently.
The alarm automatically turns off after approximately 1 minute. However, the alarm reactivates if the vehicle is tampered with again.
The alarm is activated by: . Unlocking the door or opening the lift gate without using the button on the Intelligent Key, the request switch or the key. (Even if the door is opened by releasing the door inside lock knob, the alarm will activate.)
. Opening the hood.
How to stop an activated alarm The alarm will stop by unlocking a door by on the Intelligent pushing the unlock button Key, pushing the request switch or using the key. The alarm will not stop if the ignition switch is placed in the ACC or ON position.
If the system does not operate as de- scribed above, have it checked by a NISSAN dealer.
NISSAN VEHICLE IMMOBILIZER SYS- TEM The NISSAN Vehicle Immobilizer System will not allow the engine to start without the use of the registered key. Never leave these keys in the vehicle.
Statement related to section 15 of FCC rules for NISSAN Vehicle Immobilizer System (CONT ASSY - CARD SLOT)
This device complies with part 15 of the FCC Rules and RSS-210 of Industry Cana-
Black plate (99,1)
da. Operation is subject to the following two conditions;
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation of the device.
CHANGES OR MODIFICATIONS NOT EX- PRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID THE USER’S AUTHORITY TO OPER- ATE THE EQUIPMENT.
Instruments and controls 2-27
Model "Z51-D" EDITED: 2010/ 7/ 23
service as soon as possible. Please bring all registered keys that you have when visiting a NISSAN dealer for service.
Black plate (100,1)
WINDSHIELD WIPER AND WASHER SWITCH
WARNING
In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield.
CAUTION
. Do not operate the washer continu-
ously for more than 30 seconds.
. Do not operate the washer if the
reservoir tank is empty.
. Do not
fill
the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.
. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to
Model "Z51-D" EDITED: 2010/ 7/ 23
SIC1699A
Security indicator light The security indicator light *A status of System.
indicates the the NISSAN Vehicle Immobilizer
The light blinks after the ignition switch was in the ACC, OFF and LOCK position. This function indicates the security systems equipped on the vehicle are operational.
If the NISSAN Vehicle Immobilizer System is malfunctioning, this light will remain on while the ignition switch is in the ON position.
If the light still remains on and/or the engine will not start, see a NISSAN dealer for NISSAN Vehicle Immobilizer System
2-28 Instruments and controls
Black plate (101,1)
mix the washer fluid concentrate and water.
The windshield wiper and washer operates when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
*1
INT (Type A) — intermittent operation can be adjusted by turning the knob toward *A (Slower) or *B (Faster).
*1 AUTO (Type B) — For models with the rain- sensing auto wiper system, see “RAIN- SENSING AUTO WIPER SYSTEM” later in this section.
*2 LO — continuous low speed operation
*3 HI — continuous high speed operation
Push the lever up *4
operation of the wiper.
Pull the lever toward you *5
to operate the
washer. Then the wiper will also operate several
times.
(MIST) to have one sweep
Type A
SIC3664
Type B
SIC4395
Instruments and controls 2-29
Model "Z51-D" EDITED: 2010/ 7/ 23
. High — High sensitive operation
Low — Low sensitive operation
To turn the rain-sensing auto wiper system off, push up the lever to the OFF position, or pull down the lever to the LO or HI position.
CAUTION
Do not touch the rain sensor and around it when the wiper switch is in the AUTO position and the ignition switch is in the ON position. The wipers may operate unexpectedly and cause to an injury or a wiper damage.
The rain-sensing auto wipers are in- tended for use during rain. If the switch is left in the AUTO position, the wipers may operate unexpectedly when dirt, fingerprints, oil film or insects are stuck on or around the sensor. The wipers may also operate when exhaust gas or moisture affect the rain sensor.
. When the windshield glass is coated with water repellent, the speed of the rain-sensing auto wipers may be higher even though the amount of the rainfall is small.
. Be sure to turn off the rain-sensing
SIC4017
RAIN-SENSING AUTO WIPER SYS- TEM (if so equipped) The rain-sensing auto wiper system can auto- matically turn on the wipers and adjust the wiper speed depending on the rainfall and the vehicle speed by using the rain sensor located on the upper part of the windshield.
To set the rain-sensing auto wiper system, push the lever down to the AUTO position *1 . The wiper will sweep once while the ignition switch is in the ON position.
The rain sensor sensitivity level can be adjusted
by turning the knob toward the front *2
(High)
or toward the rear *3
(Low).
2-30 Instruments and controls
Black plate (102,1)
auto wiper system when you use a car wash.
The rain-sensing auto wipers may not operate if rain does not hit the rain sensor even if it is raining.
. Using genuine wiper blades is recom- mended for proper operation of the rain-sensing auto wiper system. (See “WINDSHIELD WIPER BLADES” in the “8. Maintenance and do-it-yourself” section for wiper blade replacement.)
Model "Z51-D" EDITED: 2010/ 7/ 23
REAR WINDOW WIPER AND WASHER SWITCH
WARNING
and water.
If the rear window wiper operation is interrupted by snow or ice, the wiper may stop moving to protect its motor. If this occurs, turn the wiper switch to the OFF position and remove the snow or ice that is on and around the wiper arms. In approxi- mately 1 minute, turn the switch on again to operate the wiper.
In freezing temperatures the washer solution may freeze on the rear window glass and obscure your vision. Warm the rear window with the defroster before you wash the rear window.
CAUTION
. Do not operate the washer continu-
ously for more than 30 seconds.
. Do not operate the washer if the
reservoir tank is empty.
. Do not
fill
the window washer reservoir tank with washer fluid concentrates at full strength. Some methyl alcohol based washer fluid concentrates may permanently stain the grille if spilled while filling the window washer reservoir tank.
. Pre-mix washer fluid concentrates with water to the manufacturer’s recommended levels before pouring the fluid into the window washer reservoir tank. Do not use the window washer reservoir tank to mix the washer fluid concentrate
Black plate (103,1)
Type A
SIC3666
Type B
SIC4019
Instruments and controls 2-31
Model "Z51-D" EDITED: 2010/ 7/ 23
REAR WINDOW AND OUTSIDE MIRROR DEFROSTER SWITCH
The rear window wiper and washer operate when the ignition switch is in the ON position.
Turn the switch clockwise from the OFF position
to operate the wiper.
*1
Intermittent (INT) — intermittent operation (not adjustable)
tion
*2 Low (ON) — continuous low speed opera-
Push the switch forward *3
to operate the
washer. Then the wiper will also operate several
times.
Black plate (104,1)
To defog/defrost the rear window glass and outside mirrors (if so equipped), start the engine and push the switch *1 on. The indicator light *2 will come on. Push the switch again to turn the defroster off.
It will automatically turn off in approximately 15
minutes.
CAUTION
When cleaning the inner side of the rear window, be careful not to scratch or damage the rear window defroster.
Type A
SIC3584
2-32 Instruments and controls
Type B
SIC3667
Model "Z51-D" EDITED: 2010/ 7/ 23
HEADLIGHT AND TURN SIGNAL SWITCH
XENON HEADLIGHTS (if so equipped)
WARNING
HIGH VOLTAGE
. When xenon headlights are on, they produce a high voltage. To prevent an electric shock, never attempt to modify or disassemble. Always have your xenon headlights replaced at a NISSAN dealer.
. Xenon headlights provide consider- ably more light than conventional headlights. If they are not correctly aimed, they might temporarily blind an oncoming driver or the driver ahead of you and cause a serious accident. If headlights are not aimed correctly, immediately take your ve- hicle to a NISSAN dealer and have the headlights adjusted correctly.
When the xenon headlight is initially turned on, its brightness or color varies slightly. However, the color and brightness will soon stabilize.
The life of xenon headlights will be shortened by frequent on-off opera- tion. It is generally desirable not to turn
Black plate (105,1)
off the headlights for short intervals (for example, when the vehicle stops at a traffic signal). Even when the daytime running lights are active (Canada only), the xenon headlights do not turn on. This way the life of the xenon head- lights is not reduced.
If the xenon headlight bulb is close to burning out, the brightness will drasti- cally decrease, the light will start blinking, or the color of the light will become reddish. If one or more of the above signs appear, contact a NISSAN dealer.
SIC3668
HEADLIGHT SWITCH Lighting *1 Turn the switch to the
position:
The front park, side marker, plate and instrument lights will come on.
tail,
license
*2 Turn the switch to the
position:
Headlights will come on and all the other lights remain on.
Instruments and controls 2-33
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (106,1)
The autolight system can turn on the headlights automatically when it is dark and turn off the headlights when it is light.
If the ignition switch is pushed to the OFF position and one of the doors is opened and this condition is continued, the headlights remain on for 5 minutes.
Automatic headlights off delay:
You can keep the headlights on for up to 180
seconds after you push the ignition switch to
OFF and open any door then close all the doors.
the period of
You can adjust
the automatic
headlights off delay from 0 seconds (OFF) to
180 seconds. The factory default setting is 45
seconds.
For automatic headlights off delay setting, see “Light Off Delay” in the “4. Center display, heater, air conditioner, audio, phone and voice recognition systems” section.
SAA0642A
Be sure not to put anything on top of the photo sensor *A located on the top of the instrument panel. The photo sensor con- trols the autolight; if it is covered, the photo sensor reacts as if it is dark and the headlights will illuminate.
SIC3669
Autolight system (if so equipped) The autolight system allows the headlights to be set so they turn on and off automatically.
To set the autolight system:
1. Make sure the headlight switch is in the
AUTO position *1 .
2. Push the ignition switch to the ON position.
3. The autolight system automatically turns the
headlights on and off.
To turn the autolight system off, turn the switch to the OFF,
position.
or
2-34 Instruments and controls
Model "Z51-D" EDITED: 2010/ 7/ 23
When the headlight switch is in the
position while the ignition switch is in the ON
position, the lights will automatically turn off 5
minutes after
the ignition switch has been
pushed to the OFF position.
or
When the headlight switch remains in the or position after the lights automatically turn off, the lights will turn on when the ignition switch is pushed to the ON position.
CAUTION
. When you turn on the headlight switch again after the lights auto- matically turn off, the lights will not turn off automatically. Be sure to turn the light switch to the OFF position when you leave the vehicle for extended periods of time, other- wise the battery will be discharged. . Never leave the light switch on when the engine is not running for extended periods of time even if the headlights turn off automatically.
Daytime running light system (Canada only) The daytime running lights automatically illumi- nate when the engine is started with the parking brake released. The daytime running lights
SIC3670
Headlight beam select *1 To select the low beam, put the lever in the
neutral position as shown.
*2 To select the high beam, push the lever
forward while the switch is in the position. Pull it back to select the low beam. *3 Pulling the lever toward you will flash the headlight high beam even when the head- light switch is in the OFF position.
Battery saver system A chime will sound when the driver side door is or opened with the light switch in the position and the ignition switch in the ACC,
OFF or LOCK position.
Black plate (107,1)
operate with the headlight switch in the OFF position. Turn the position or position for full headlight switch to the illumination when driving at night.
in the
If the parking brake is applied before the engine is started, the daytime running lights do not illuminate. The daytime running lights illuminate once the parking brake is released. The daytime running lights will remain on until the ignition switch is pushed to the OFF position.
WARNING
When the daytime running light system is active, tail lights on your vehicle are not on. It is necessary at dusk to turn on your headlights. Failure to do so could cause an accident injuring yourself and others.
Instruments and controls 2-35
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (108,1)
SIC3585
SIC3671
SIC3672
TURN SIGNAL SWITCH *1 Turn signal Move the lever up or down to signal the turning direction. When the turn is completed, the turn signals cancel automatically. *2 Lane change signal To indicate a lane change, move the lever up or down to the point where lights begin flashing.
FOG LIGHT SWITCH (if so equipped) To turn the fog lights on, turn the headlight position, then turn the switch switch to the position. To turn them off, turn the to the switch to the OFF position.
The headlights must be on for the fog lights to operate.
Instrument brightness control The instrument brightness control operates when the ignition switch is in the ON position. Pushing the control switch *A once will change the brightness to the night mode. Pushing the control switch *B once will change the brightness to the day mode.
the brightness of
To adjust instrument panel lights, push the control switches. Pushing the upper switch *A will brighten the lights. When the brightness reaches the maximum level, a beep will sound. The lower switch *B dims the lights. Repeatedly pushing the lower switch will turn the lights off and a beep will sound.
2-36 Instruments and controls
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (109,1)
HAZARD WARNING FLASHER SWITCH
HORN
Turn signals do not work when the hazard warning flasher lights are on.
The flasher can be actuated with the ignition switch in any position.
Some state laws may prohibit the use of the hazard warning flasher switch while driving.
SIC2574
Push the switch on to warn other drivers when you must stop or park under emergency condi- tions. All turn signal lights will flash.
WARNING
If stopping for an emergency, be sure to move the vehicle well off the road.
. Do not use the hazard warning flashers while moving on the high- way unless unusual circumstances force you to drive so slowly that your vehicle might become a hazard to other traffic.
To sound the horn, push the pad area *A of the steering wheel.
SIC3586
WARNING
Do not disassemble the horn. Doing so could affect proper operation of the supplemental front air bag system. Tampering with the supplemental front air bag system may result in serious personal injury.
Instruments and controls 2-37
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (110,1)
HEATED STEERING WHEEL (if so equipped)
HEATED SEATS (if so equipped)
NOTE: If the surface temperature of the steering wheel is above 688F (208C) when the switch is turned on, the system will not heat the steering wheel. This is not a malfunction.
WARNING
Do not use or allow occupants to use the seat heater if you or the occupants cannot monitor elevated seat tempera- tures or have an inability to feel pain in body parts that contact the seat. Use of the seat heater by such people could result in serious injury.
CAUTION
The battery could run down if the seat heater is operated while the engine is not running.
. Do not use the seat heater for extended periods or when no one is using the seat.
. Do not put anything on the seat which insulates heat, such as a blanket, cushion, seat cover, etc. Otherwise, the seat may become overheated.
. Do not place anything hard or heavy on the seat or pierce it with a pin or similar object. This may result in damage to the heater.
Model "Z51-D" EDITED: 2010/ 7/ 23
SIC4401
The heated steering wheel system is designed to operate only when the surface temperature of the steering wheel is below 688F (208C).
Push the heated steering wheel switch to warm the steering wheel after the engine starts. The indicator light *1 on the switch will illuminate. If the surface temperature of the steering wheel is below 688F (208C), the system will heat the steering wheel and cycle off and on to maintain a temperature above 688F (208C). The indicator light will remain on as long as the system is on.
Push the switch again to turn the heated steering wheel system off manually. The indica- tor light will turn off.
2-38 Instruments and controls
. Any liquid spilled on the heated seat should be removed immediately with a dry cloth.
. When cleaning the seat, never use gasoline, thinner, or any similar materials.
If any malfunctions are found or the heated seat does not operate, turn the switch off and have the system checked by a NISSAN dealer.
Black plate (111,1)
3. To turn off the heater, return the switch to the level position. Make sure the indicator light goes off.
The heater is controlled by a thermostat, automatically turning the heater on and off. The indicator light will remain on as long as the switch is on.
When the vehicle’s interior is warmed, or before you leave the vehicle, be sure to turn off the switch.
Instruments and controls 2-39
Model "Z51-D" EDITED: 2010/ 7/ 23
SIC2770
The seats are warmed by built-in heaters. The switches located on the center console and rear doors (if so equipped for rear seats) can be operated independently of each other.
1. Start the engine.
2. Select heat range.
*1 For high heat, push the HI (High) side of
the switch.
*2 For low heat, push the LO (Low) side of
the switch.
The indicator light in the switch *3 will illuminate when the heater is on.
CLOCK
MODELS WITH COLOR DISPLAY To adjust the clock on the front color display, use the SETTING button on the center multi- function control panel. See “HOW TO USE SETTING BUTTON” in the “4. Center display, heater, air conditioner, audio, phone and voice recognition systems” section.
The clock settings display cannot be operated while driving. Stop the vehicle in a safe place and apply the parking brake before setting the clock.
2-40 Instruments and controls
Black plate (112,1)
5. Push the CLOCK button *1
knob *2
to enter.
or AUDIO
The display will display after 10 seconds.
return to the regular clock
If the power supply is disconnected, the clock will not indicate the correct time.
Readjust the time.
SIC3802
MODELS WITHOUT COLOR DISPLAY The digital clock (in the audio unit) displays the time when the ignition switch is in the ACC or ON position.
Adjusting the time
1. Push and hold the CLOCK button *1
for more than 2 seconds until the display shows “Hour Adjust”.
2. Turn the AUDIO knob *2
3. Push the CLOCK button *1
to adjust hours.
or AUDIO to enter. The display will show
knob *2
“Minute Adjust”.
4. Turn the AUDIO knob *2
to adjust minutes.
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (113,1)
VEHICLE DYNAMIC CONTROL (VDC) OFF SWITCH
POWER OUTLET
SSD1153
The vehicle should be driven with the Vehicle Dynamic Control (VDC) system on for most driving conditions.
If the vehicle is stuck in mud or snow, the VDC system reduces the engine output to reduce wheel spin. The engine speed will be reduced even if the accelerator is depressed to the floor. If maximum engine power is needed to free a stuck vehicle, turn the VDC system off.
To turn off the VDC system, push the VDC OFF switch. The
indicator will illuminate.
Push the VDC OFF switch again or restart the engine to turn on the system. (See “VEHICLE DYNAMIC CONTROL (VDC) SYSTEM” in the “5. Starting and driving” section.)
Center console
SIC3587
Console box — Type A
SIC3652
Cargo area
SIC3651
Console box — Type B
Instruments and controls 2-41
SIC3653
Model "Z51-D" EDITED: 2010/ 7/ 23
To use the power outlet, pull illustrated.
the cover as
contact the outlet.
CAUTION
The outlet and plug may be hot during or immediately after use.
. Do not use with accessories that exceed a 12 volt, 120W (10A) power draw. Do not use double adapters or more than one electrical accessory. . Use power outlet with the engine running to avoid discharging the vehicle battery.
. Avoid using power outlet when the air conditioner, headlights or rear window defroster is on.
This power outlet is not designed for use with a cigarette lighter unit. . Push the plug in as far as it will go. If good contact is not made, the plug may overheat or the internal tem- perature fuse may open.
. Before inserting or disconnecting a plug, be sure the electrical acces- sory being used is turned OFF.
. When not in use, be sure to close the cap. Do not allow water to
2-42 Instruments and controls
Black plate (114,1)
CIGARETTE LIGHTER AND ASHTRAY (if so equipped)
SIC3588
To open the ashtray lid, push the lid down and release it *1 . To empty the ashtray, pull out *2 . The cigarette lighter operates when the ignition switch is in the ON position. Push the lighter in all the way *3 , then release it. When the lighter is heated, it will spring out. Return the lighter to its original position after use.
Model "Z51-D" EDITED: 2010/ 7/ 23
CAUTION
The cigarette lighter socket is a power source for the cigarette light- er element only. The use of the cigarette lighter socket as a power source for any other accessory is not recommended.
. Do not use any other power outlet
for an accessory lighter.
STORAGE
CUP HOLDERS
CAUTION
. Avoid abrupt starting and braking when the cup holder is being used to prevent spilling the drink. If the liquid is hot, it can scald you or your passenger.
. Use only soft cups in the cup holder. Hard objects can injure you in an accident.
Black plate (115,1)
SIC3118
Front
To open the cup holder, push the lid *1 . To remove the inner tray for cleaning, pull it up as illustrated *2 .
Instruments and controls 2-43
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (116,1)
direct sunlight. The heat may da- mage the glasses.
Pull the armrest forward until it is horizontal.
Rear
SUNGLASSES HOLDER
SIC3042
SIC3589
WARNING
Keep the sunglasses holder closed while driving to prevent an accident. To open the sunglasses holder, push *1 .
CAUTION
. Do not use for anything other than
glasses.
. Do not leave glasses in the sun- glasses holder while parking in
2-44 Instruments and controls
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (117,1)
SIC3590
SIC3654
Front
CONSOLE BOX When the lever *A (driver’s seat side) is pulled, the upper case is available for storing some small items. When the lever *B (front passen- ger’s seat side) is pulled, the bottom case is available for storing some larger ones.
GLOVE BOX
WARNING
Keep glove box lid closed while driving
to help prevent injury in an accident or a
sudden stop.
To open the glove box, pull the handle *1 .
To close, push the lid in until the lock latches.
To lock *2 /unlock *3
the glove box, use the
mechanical key. For the mechanical key usage,
see “KEYS” in the “3. Pre-driving checks and
adjustments” section.
Instruments and controls 2-45
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (118,1)
SIC3591
SIC3593
To open, push the knob *1 and pull out *2 .
Rear
STORAGE BOX (if so equipped)
To open, push the storage box lid *1
illustrated.
The inner tray can be removed *2 as illustrated.
Do not place valuable items in the storage
box.
as
Do not use the storage box as an ashtray.
Type A
SIC3655
2-46 Instruments and controls
Type B
SIC3656
Model "Z51-D" EDITED: 2010/ 9/ 28
CARGO FLOOR BOX Type A 1. To open the cargo floor box, pull the strap *A .
2. Remove the strap *B from the back side of the board and hang it on the opening of the lift gate.
Type B To open the cargo floor box, push *A . To close, push the lid until the lock latches. The net partitions can be removed *B to make a larger storage space.
SIC3594
The cargo floor box needs to be removed when you need a spare tire. (See “FLAT TIRE” in the “6. In case of emergency” section.)
LUGGAGE SIDE BOX To open the luggage side box, pull up the strap.
CAUTION
To avoid damage, do not load more than 22 lbs (10 kg) of cargo into the cargo floor box.
Black plate (119,1)
SIC3595
CARGO COVER (if so equipped) The cargo cover keeps the contents in the cargo area hidden from the outside.
To use the cargo cover, pull it out and hang both sides on the hooks *1 .
Instruments and controls 2-47
Model "Z51-D" EDITED: 2010/ 9/ 28
restraint top tether strap is da- maged.
— If the cargo cover contacts the top tether strap when it is at- tached to the top tether anchor, remove the cargo cover from the vehicle or secure it on the cargo floor below its attachment loca- tion. If the cargo cover is not removed, it may damage the top tether strap during a collision.
— Do not allow cargo to contact the top tether strap when it is attached to the top tether an- chor. Properly secure the cargo so it does not contact the top tether strap. Cargo that is not properly secured or that con- tacts the top tether strap may damage the top tether strap during a collision.
To use the sub cover, hang the straps on the back of the headrest *2 . To stow the cargo cover, remove it from the hooks and hold until it is retracted.
To remove the cargo cover, stow the cover and pull the left side of the holder to the opposite side *3 .
WARNING
. Never put anything on the cargo cover, no matter how small. Any object on it could cause an injury in an accident or sudden stop.
. Close the cargo cover when folding
the rear seat.
. Do not leave the cargo cover in the vehicle with it disengaged from the holder.
. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. Do not place cargo higher than the seatbacks. In a sudden stop or collision, unse- cured cargo could cause personal injury.
. Your child could be seriously injured or killed in a collision if the child
2-48 Instruments and controls
Black plate (120,1)
LUGGAGE HOOKS
SIC3596
WARNING
. Always make sure that the cargo is properly secured. Use the suitable
Model "Z51-D" EDITED: 2010/ 7/ 23
ropes and hooks.
. Unsecured cargo can become dan- gerous in an accident or sudden stop.
CAUTION
Do not apply a total load of more than 22 lb (10 kg) *A or 7 lb (3 kg) *B to a single hook.
Black plate (121,1)
Technical and consumer information” section.
WARNING
. Drive extra carefully when the vehi- cle is loaded at or near the cargo carrying capacity, especially if the significant portion of that load is carried on the roof rack.
. Heavy loading of the roof rack has the potential to affect the vehicle stability and handling during sud- den or unusual handling maneuvers. . Roof rack load should be evenly
distributed.
. Do not exceed maximum roof rack
load weight capacity.
. Properly secure all cargo with ropes or straps to help prevent it from sliding or shifting. In a sudden stop or collision, unsecured cargo could cause personal injury.
CAUTION
Use care when placing or removing items from the roof rack. If you cannot comfortably lift the items onto the roof
Instruments and controls 2-49
Model "Z51-D" EDITED: 2010/ 7/ 23
SIC3597
ROOF RACK (if so equipped) Always distribute the luggage evenly on the roof rack. Do not load more than 165 lb (75 kg) (black) or 220 lb (100 kg) (silver) on the roof rails. Observe the maximum load limit shown on the crossbars or roof carriers when you attach them on the roof rails. Contact a NISSAN dealer for crossbar or other equipment information. Be careful that your vehicle does not exceed the Gross Vehicle Weight Rating (GVWR) or its Gross Axle Weight Rating (GAWR front and rear). The GVWR and GAWR are located on the F.M.V.S.S. or C.V.M.S.S. certification label (lo- cated on the driver’s door pillar). For more information regarding GVWR and GAWR, see “VEHICLE LOADING INFORMATION” in the “9.
rack from the ground, use a ladder or stool.
SIC3505
COAT HOOKS The coat hooks are equipped beside the rear personal lights.
CAUTION
Do not place items which are more than 2 lb (1 kg) on the hook.
Black plate (122,1)
WINDOWS
POWER WINDOWS
WARNING
. Make sure that all passengers have their hands, etc. inside the vehicle while it is in motion and before closing the windows. Use the win- dow lock switch to prevent unex- pected use of the power windows.
. Do not leave children unattended inside the vehicle. They could un- knowingly activate switches or con- trols and become trapped in the window. Unattended children could become involved in serious acci- dents.
The power windows operate when the ignition
switch is in the ON position or for about 45
seconds after the ignition switch is pushed to
the OFF position.
front
passenger’s door is opened during this period
of about 45 seconds, power to the windows is
canceled.
the driver’s or
If
2-50 Instruments and controls
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (123,1)
Locking passengers’ windows When the lock button *C is pushed in, only the driver side window can be opened or closed. Push it in again to cancel.
SIC3283A
Front passenger side window
Main power window switch (driver’s side) 1. Driver side window 2. 3. Rear left passenger side window 4. Rear right passenger side window 5. Window lock button To open or close the window, push down *A or pull up *B the switch and hold it. The main switch (driver side switches) will open or close all the windows.
SIC3241
Passenger side power window switch The passenger side switch will open or close only the corresponding window. To open or close the window, push down or pull up the switch and hold it.
Instruments and controls 2-51
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (124,1)
Auto reverse function
1. Push the ignition switch to the ON position.
2. Close the door.
3. Open the window completely by operating
the power window switch.
4. Pull the power window switch and hold it to close the window, and then hold the switch more than 3 seconds after the window is closed completely.
5. Release the power window switch. Operate the window by the automatic function to confirm the initialization is complete.
6. Perform steps 2 through 5 above for other
windows.
If the power window automatic function does not operate properly after performing the pro- cedure above, have your vehicle checked by a NISSAN dealer.
WARNING
There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the window.
If the control unit detects something caught in the window as it is closing, the window will be immediately lowered.
The auto reverse function can be activated when the window is closed by automatic operation when the ignition switch is in the ON position or for 45 seconds after the ignition switch is pushed to the OFF position.
Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the window occurs.
If the windows do not close automatically If the power window automatic function (closing only) does not operate properly, perform the following procedure to initialize the power window system.
Model "Z51-D" EDITED: 2010/ 7/ 23
SIC3285
Automatic operation (for front door win- dows) To fully open or close the window, completely push down or pull up the switch and release it; it need not be held. The window will automatically open or close all the way. To stop the window, just push or the switch in the opposite direction.
lift
A light push or pull on the switch will cause the window to open or close until the switch is released.
2-52 Instruments and controls
AUTOMATIC MOONROOF AND SUN- SHADES The moonroof and sunshades only operates when the ignition switch is in the ON position.
The automatic moonroof and sunshades are operational for about 45 seconds, even if the ignition switch is pushed to the OFF position. If the driver’s door or the passenger’s door is opened during this period of about 45 seconds, power to the moonroof and sunshades is canceled.
MOONROOF (if so equipped)
WARNING
In an accident you could be thrown from the vehicle through an open moonroof. Always use seat belts and child restraints.
. Do not allow anyone to stand up or extend any portion of their body out of the moonroof opening while the vehicle is in motion or while the moonroof is closing.
CAUTION
. Remove water drops, snow, ice or sand from the moonroof before opening.
. Do not place any heavy object on the moonroof or surrounding area. . Do not push or pull on the sun- shade. Doing so can damage the sunshade.
Black plate (125,1)
SIC3598
of
Sliding sunshade and moonroof
When the OPEN side *1
the moonroof
switch is pushed, the front and rear sunshades
will fully open. When the switch is pushed again,
the moonroof will fully open.
When the CLOSE side *2
of the moonroof
switch is pushed, the moonroof will automati-
cally close. Push the switch again, and the front
and rear sunshades will close.
When the OPEN or CLOSE side of the moon-
roof switch is pushed to the second detent (*3
or *4 ), both the sunshade and moonroof will
open or close.
To stop the sunshades or moonroof during the
Instruments and controls 2-53
Model "Z51-D" EDITED: 2010/ 7/ 23
operation, push either of the OPEN *1 , CLOSE *2 or UP *5 of the switch. Tilting moonroof To tilt up the moonroof, push the moonroof switch to the up position *5 . To tilt down the moonroof, push the switch to the up position *5 or push the CLOSE side *2 of the switch.
When the moonroof is tilted up, push the CLOSE side of the moonroof switch to the second detent *4 . The moonroof will tilt down and the sunshades will close.
Auto reverse function
WARNING
There are some small distances imme- diately before the closed position which cannot be detected. Make sure that all passengers have their hands, etc., in- side the vehicle before closing the moonroof.
If the control unit detects something caught in the moonroof and sunshades when they are closing, the moonroof will be immediately opened.
2-54 Instruments and controls
Black plate (126,1)
4. Push and hold the CLOSE side *2 of the
moonroof switch for 10 seconds.
5. The moonroof and sunshades will fully open
and then close.
6. Check if normally.
the moonroof switch operates
If the moonroof does not operate properly after performing the procedure above, have your vehicle checked by a NISSAN dealer.
The auto reverse function can be activated when the moonroof and sunshades are closed by automatic operation when the ignition switch is in the ON position or for about 45 seconds after the ignition switch is pushed to the OFF position.
If the moonroof and sunshades cannot be closed automatically when the auto reverse function activates due to a malfunction, push and hold the CLOSE side *2 of the moonroof switch.
Depending on the environment or driving conditions, the auto reverse function may be activated if an impact or load similar to something being caught in the moonroof occurs.
If the moonroof does not operate If the moonroof does not operate properly, perform the following procedure to initialize the moonroof operation system.
1.
If the moonroof is open, close it fully by pushing the CLOSE side *2 of the moon- roof switch.
2. Push and hold the CLOSE side *2 of the
moonroof switch.
3. Release the moonroof switch after
the moonroof or sunshade moves slightly to the closed position.
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (127,1)
INTERIOR LIGHTS
SIC3249
SIC3250
SIC3251
MAP LIGHTS Push the button as illustrated to turn the light on or off.
PERSONAL LIGHTS Rear Push the button as illustrated to turn the light on or off.
INTERIOR LIGHT CONTROL SWITCH The interior light control switch has three positions: ON, DOOR and OFF.
ON position
When the switch is in the ON position *1
map lights and rear personal
nate.
lights will
the illumi-
DOOR position When the switch is in the DOOR position *2 , the map lights and rear personal lights will illuminate under the following conditions:
ignition switch is switched to the LOCK position
Instruments and controls 2-55
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (128,1)
MOOD LIGHTS
— remain on while the door
is opened. When the door is closed, the lights go off.
OFF position When the switch is in the OFF position *3 , the lights will not the condition.
regardless of
illuminate,
CAUTION
Do not use for extended periods of time with the engine stopped. This could result in a discharged battery.
SIC3599
Map lights
The mood lights *A located in the following positions will illuminate whenever the headlight switch is in the
next to the map lights
position.
or
under the instrument panel
under the driver’s power window switch
The brightness of adjusted with the illumination control buttons.
the mood lights can be
See “Instrument brightness control” earlier in this section.
Model "Z51-D" EDITED: 2010/ 7/ 23
— remain on for about 15 seconds.
doors are unlocked by pushing the UN- LOCK button on the Intelligent Key or door handle request switch with the ignition switch in the LOCK position
— remain on for about 15 seconds.
any door is opened and then closed with the ignition switch in the LOCK position
— remain on for about 15 seconds.
any door is opened with the ignition switch in the ACC or ON position
— remain on while the door
is opened. When the door is closed, the lights go off.
The lights will also turn off after 15
minutes when the lights remain illumi-
nated after the ignition switch has been
pushed to the OFF or LOCK position to
prevent the battery from becoming dis-
charged.
When the auto interior illumination is set to the OFF position (see “VEHICLE INFORMATION AND SETTINGS” in the “4. Center display, heater, air conditioner, audio, phone and voice recognition systems” section), the lights will illuminate under the following condition:
any door is opened with the ignition switch in any position
2-56 Instruments and controls
VANITY MIRROR LIGHTS
CARGO LIGHTS
SIC2064
The light on the vanity mirror will turn on when the cover on the vanity mirror is opened.
When the cover is closed, the light will turn off.
The lights will turn off after 15 minutes when the lights remain illuminated to prevent the battery from becoming dis- charged.
SIC2131A
When the switch is in the ON position *1 , the light illuminates while the lift gate is opened. When the lift gate is closed, the light will turn off. When the switch is in the OFF position *2 , the light will turn off.
The lights will turn off after 15 minutes when the light remain illuminated to pre- vent the battery from becoming dis- charged.
Black plate (129,1)
HomeLink® UNIVERSAL TRANSCEIVER (if so equipped)
HomeLink® Universal Transceiver provides a convenient way to consolidate the functions of up to three individual hand-held transmitters into one built-in device. HomeLink® Universal Transceiver: . Will operate most Radio Frequency (RF) devices such as garage doors, gates, home and office lighting, entry door locks and security systems.
Is powered by your vehicle’s battery. No separate batteries are required. the vehicle’s battery is discharged or is dis- connected, HomeLink® will retain all pro- gramming.
If
Once HomeLink® Universal Transceiver is programmed, retain the original transmit- ter for future programming procedures (Example: new vehicle purchases). Upon sale of the programmed HomeLink® Universal Transceiver buttons should be erased for security purposes. For additional information, see “PRO- GRAMMING HomeLink®” later in this sec- tion.
the vehicle,
WARNING
. Do not use HomeLink® Universal Transceiver with any garage door opener that lacks safety stop and
Instruments and controls 2-57
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (130,1)
1996) have “rolling code protection”. To pro- gram a garage door opener equipped with “rolling code protection”; you will need to use a ladder to get up to the garage door opener motor to be able to access the “smart or learn” program button.
SIC3612
1. To begin, push and hold the 2 outer Home- Link® buttons (to clear the memory) until the indicator light *A blinks (after 20 seconds). Release both buttons.
2. Position the end of the hand-held transmitter 1 to 3 in (20 to 70 mm) away from the HomeLink® surface.
Model "Z51-D" EDITED: 2010/ 7/ 23
reverse features as required by federal safety standards. (These standards became effective for opener models manufactured after April 1, 1982.) A garage door opener which cannot detect an object in the path of a closing garage door and then automatically stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features in- creases the risk of serious injury or death.
. During programming procedure, your garage door or security gate may open or close. Make sure that people and objects are clear of the garage door, gate, etc. that you are programming.
. Your vehicle’s engine should be turned off while programming HomeLink® Universal Transceiver.
PROGRAMMING HomeLink® To program your HomeLink® Transceiver to operate a garage door, gate, or entry door opener, home or office lighting, you need to be at the same location as the device. Note: Garage door openers (manufactured after
2-58 Instruments and controls
Black plate (131,1)
5.
button - releasing when the device begins to activate. If the indicator light on HomeLink® blinks rapidly for two seconds and then turns solid, HomeLink® has picked up a “rolling code” garage door opener signal. You will need to proceed with the next steps to train Home- Link®, completing the programming may require a ladder and another person for convenience.
6. Push and release the program button located on the garage door opener’s motor to activate the “training mode”. This button is usually located near the antenna wire that hangs down from the motor. the wire originates from under a light lens, you will need to remove the lens to access the training button.
If
NOTE: Once you have pushed and released the training button on the garage door opener’s motor and the “training light” is lit, you have 30 seconds in which to perform step 7. For convenience, use the help of a second person to assist when performing this step.
7. Quickly (within 30 seconds of pushing and releasing the garage door opener training button) and firmly push and release the HomeLink® button you’ve just programmed.
Push and release the HomeLink® button up to three times to complete the training.
8. Your HomeLink® button should now be programmed. To program the remaining HomeLink® buttons for additional door or gate openers, follow steps 2 through 8 only.
NOTE: Do not repeat step 1 unless you want to “clear” all previously programmed Home- Link® buttons.
If you have any questions or are having difficulty programming your HomeLink® buttons, please to the HomeLink® web site at: www. refer homelink.com or call 1-800-355-3515.
to 1992, D.O.C.
PROGRAMMING HomeLink® FOR CA-
NADIAN CUSTOMERS
Prior
regulations required
hand-held transmitters to stop transmitting after
2 seconds. To program your hand-held trans-
mitter to HomeLink®, continue to push and hold
the HomeLink® button (note steps 2 through 4
under “Programming HomeLink®”) while you
push and re-push (“cycle”) your hand-held
transmitter every 2 seconds until the indicator
light flashes rapidly (indicating successful pro-
gramming).
Instruments and controls 2-59
Model "Z51-D" EDITED: 2010/ 7/ 23
SIC3613
3. Using both hands, simultaneously push and hold both the HomeLink® button you want to program and the hand-held transmitter button.
DO NOT release the buttons until step 4 has been completed.
4. Hold down both buttons until the indicator light on HomeLink® flashes, changing from a “slow blink” to a “rapid blink”. This could take up to 90 seconds. When the indicator light blinks rapidly, both buttons may be released. The rapidly flashing light indicates successful programming. To activate the garage door or other programmed device, push and hold the programmed HomeLink®
Black plate (132,1)
NOTE: If programming a garage door opener, etc., it is advised to unplug the device during the “cycling” process to prevent possible damage to the garage door opener com- ponents.
OPERATING THE HomeLink® UNIVER- SAL TRANSCEIVER HomeLink® Universal Transceiver (once pro- grammed) may now be used to activate the garage door, etc. To operate, simply push the appropriate programmed HomeLink® Universal Transceiver button. The red indicator light will illuminate while the signal is being transmitted.
PROGRAMMING TROUBLE-DIAGNO- SIS If HomeLink® does not quickly learn the hand- held transmitter information:
replace the hand-held transmitter batteries with new batteries.
position the hand-held transmitter with its battery area facing away from the Home- Link® surface. push and hold both the HomeLink® and hand-held transmitter buttons without inter- ruption.
position the hand-held transmitter 2 to 5 in
2-60 Instruments and controls
(50 to 127 mm) away from the HomeLink® surface. Hold the transmitter in that position for up to 15 seconds. If HomeLink® is not programmed within that time, try holding the transmitter in another position - keeping the indicator light in view at all times.
If you continue to have programming difficulties, please contact the NISSAN Consumer Affairs Department. The phone numbers are located in the Foreword of this Owner’s Manual.
CLEARING THE PROGRAMMED IN-
FORMATION
Individual buttons cannot be cleared, however to
clear all programming, push and hold the two
outside buttons and release when the indicator
light begins to flash (in approximately 20
seconds).
REPROGRAMMING A SINGLE Home- Link® BUTTON To reprogram a HomeLink® Universal Transcei- ver button, complete the following. 1. Push and hold the desired HomeLink® button. Do not release the button until step 4 has been completed.
2. When the indicator light begins to flash
slowly (after 20 seconds), position the
hand-held transmitter 2 to 5 in (50 to 127
mm) away from the HomeLink® surface.
3. Push and hold the hand-held transmitter
button.
4. The HomeLink® indicator light will flash, first slowly and then rapidly. When the indicator light begins to flash rapidly, release both buttons.
The HomeLink® Universal Transceiver button has now been reprogrammed. The new device can be activated by pushing the HomeLink® button that was just programmed. This procedure will not affect any other programmed HomeLink® buttons.
IF YOUR VEHICLE IS STOLEN If your vehicle is stolen, you should change the codes of any non-rolling code device that has been programmed into HomeLink®. Consult the Owner’s Manual of each device or call the manufacturer or dealer of those devices for additional information.
When your vehicle is recovered, you will need to reprogram the HomeLink® Univer- sal Transceiver with your new transmitter information.
FCC Notice:
This device complies with FCC rules part 15. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) This
Model "Z51-D" EDITED: 2010/ 7/ 23
device must accept any interference that may be received, including interference that may cause undesired operation.
The transmitter has been tested and complies with FCC and DOC/MDC rules. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the device.
DOC: ISTC 1763K1313
FCC I.D.: CB2V67690
Black plate (133,1)
Instruments and controls 2-61
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (134,1)
MEMO
2-62 Instruments and controls
Model "Z51-D" EDITED: 2010/ 7/ 23
Black plate (10,1)
3 Pre-driving checks and adjustments
Keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
NISSAN Vehicle Immobilizer System keys . . . . . . . . . . . . 3-2
Intelligent Key system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
Mechanical key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Valet hand-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Doors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Locking with mechanical key. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Opening and closing windows with the
mechanical key . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Locking with inside lock knob . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Locking with power door lock switch . . . . . . . . . . . . . . . . . . 3-6
Automatic door locks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-6
Child safety rear door lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Intelligent Key system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Intelligent Key operating range . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Door locks/unlocks precaution . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9
Intelligent Key operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-10
Battery saver system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Warning signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13
Troubleshooting guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Remote keyless entry system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-15
How to use remote keyless entry system . . . . . . . . . . . 3-16
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-19
Operating manual lift gate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-20
Operating power lift gate (if so equipped) . . . . . . . . . . 3-20
Auto closure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-23
Lift gate release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Fuel-filler door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Opening fuel-filler door. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Fuel-filler cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-24
Tilt/telescopic steering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Manual operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-26
Electric operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-27
Mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Inside mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-28
Outside mirrors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Vanity mirror. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
Automatic drive positioner (if so equipped). . . . . . . . . . . . . 3-31
Entry/exit function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
Memory storage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
System operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Model "Z51-D" EDITED: 2010/ 7/ 23
KEYS
A key number plate is supplied with your keys. Record the key number and keep it in a safe place (such as your wallet), not in the vehicle. If you lose your keys, see a NISSAN dealer for duplicates by using the key number. NISSAN does not record any key numbers so it is very important to keep track of your key number plate.
A key number is only necessary when you have lost all keys and do not have one to duplicate from. If you still have a key, this key can be duplicated by a NISSAN dealer.
Type A
SPA2406