2008 Jeep Wrangler Owners Manual

NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half doors, remove each half door window by opening the door and lifting the half door window out. NOTE: Stow half door windows carefully outside of the vehicle, never inside to avoid scratches.

146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

3. Unclip and move the sun visors to the side. 4. Release the header latches and leave the hooks in the loops on the windshield.

5. Open the swing gate. 6. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets.

• Unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid scratch- ing.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147

7. Undo the Velcro威 that runs along the top and rear edge of the side window. 8. Beginning from the rear lower corner, completely unzip the window.

9. Once unzipped, remove side window retainers from the door channel and body side channel. Repeat this step on the opposite side.

148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle.

11. As you begin to lower the top, fold the sail panels so that they rest on top of the soft top.

NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow.

12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149

13. Completely release the latches from the loops on the windshield frame. If your vehicle is not equipped with the Sunrider package, proceed to Step 16.

150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

14. Make sure the plastic sleeves are slid forward over the Sunrider link (Sunrider Models Only).

15. Unlatch the side bows from both door rails (Sunrider Models Only).

16. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake lamp. Move to the front of the vehicle. Grasp the side bow behind the header and lift the top, folding it toward the rear of the vehicle.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151

portion of the top from flapping outside of the vehicle. When the top is completely down, position the drip rails so they make a “v-shape”, this prevents damage to the soft top material.

17. Tuck the fabric and the check straps between the bows and as far inward as possible. This will keep any

18. Close front header latches. 19. Remove door frames, Frame” in this section.

if desired. Refer to “Door

152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Putting Up The Soft Top

1 — Header Bow 2 — 2– Bow 3 — 3–Bow 4 — Sail Panel 5 — Plastic Retainer

6 — Body Side Retainer 7 — Quarter Window 8 — Check Strap 9 — Front Retainer — Quarter Window 10 — Bottom Retainer — Quarter Window

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153

1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels

154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

1. Unclip and move the sun visors to the side. 2. Install door frames, if removed. Refer to “Door Frame” in this section. 3. Make sure the plastic sleeve is slid rearward over Sunrider link (Sunrider Models Only).

4. Standing on the side of the vehicle, lift the top by the side bow and the 2–bow (middle bow) up and over the sports bar until the header rests on the top of the windshield frame.

5. Before attaching the header latches, be sure that the top retainers above the door are not trapped between the top and the door frame.

6. Make sure the Sunrider bracket on the side bows latches to the door rails (Sunrider Models Only). 7. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155

8. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the shortened rail edge.

156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

9. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow.

10. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) towards the rear window loose (on both sides). Pulling down on the rear roof bow (3–bow) will aid to reach the channel with the retainers.

11. To install the side windows, affix the window tem- porarily by attaching to the Velcro威 in the rear corner. Start the zipper but close only about 1 in (2.5 cm).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157

12. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window.

158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

13. Continue closing the zipper only along the top edge of the window.

14. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the Velcro威 along the top and rear of the window. Repeat this step for the opposite side.

15. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed.

16. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159

17. Run the zipper fully around to the right side of the window.

160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

18. Grasp the swing gate bar and position it into the swing gate brackets.

20. Open the doors and insert the roof retainers into the channels above the door, starting at the front and work- ing rearward.

19. Apply downward pressure on the top corner of the rear soft top bow (3–bow), then complete attaching the sail panel retainers into the body side channel.

21. Close the header latches and return the sun visors to their secured position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161

To Open 1. Insert finger behind the plastic retainer. Pull down and roll the retainer out of the channel. Repeat this on the other side.

SUNRIDER (TWO-DOOR MODELS) — IF EQUIPPED

If you are going to be driving faster than 40 mph NOTE: (64 km/h) with the Sunrider feature open, it is recom- mended that you remove the rear window of the vehicle.

162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

2. Unclip and move the sun visors to the side. 3. Release the header latches from the loops on the windshield frame.

4. Slide the plastic sleeve forward.

5. Grasp the header and lift the top back. Make sure the material is folded back as shown. NOTE: The Sunrider latch on the door rail should not be activated for Sunrider use. If activated, the soft top must be reinstalled starting from the sail panels.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163

6. Locate straps to secure side bows. Wrap straps around bows as shown. Repeat on the other side.

7. Reposition sun visors.

164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

To Close 1. Remove straps from side bows. 2. Unclip and move sun visors to the side. 3. Grasp the front header and pull to the front of the vehicle. 4. Hook header latches to the loops on the windshield frame, close latches, and return sun visor’s to their original position. 5. Slide plastic sleeve rearward over Sunrider link. 6. Tuck drip rail retainers into door frame slots.

SUNRIDER (FOUR-DOOR MODELS) — IF EQUIPPED

If you are going to be driving faster than 40 mph NOTE: (64 km/h) with the Sunrider feature open, it is recom- mended that you remove the rear window of the vehicle. To Open 1. Above the front of the rear door, place finger up into the cutout in the plastic retainer and pull down, rolling both the front and rear retainers out of the door frame. Repeat this on the other side. NOTE: All plastic retainers must be removed from the door rail prior to the operation of the Sunrider.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165

3. Release the header latches from the loops on the windshield frame.

2. Unclip and move the sun visors to the side.

166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

4. Grasp the front side bow behind the header, and lift the top.

5. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck.

6. Fold the top material so that the plastic retainers form a “W” as shown. Enter the vehicle, and move the material into two folds. Ensure that the straps are securely stowed.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167

7. Close the front header latches. 8. Secure the top by using the two provided straps. Each strap will wrap around the side bow and Velcro威 to itself, use one strap on each side of the vehicle.

To Close Perform the above steps in the opposite order.

168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

SOFT TOP (FOUR-DOOR MODELS)

CAUTION!

• The soft top is not designed to carry any additional loads such as roof racks, spare tires, building, hunting, or camping supplies, and/or luggage, etc. Also, it was not designed as a structural member of the vehicle, and thus cannot properly carry any additional loads other than environmental (rain, snow, etc.).

If the temperature is below 72°F (24°C) and/or the top has been folded down for a period of time, the top will appear to have shrunk when you raise it, making it difficult to put up. This is caused by a natural contraction of the vinyl coating on the fabric top. Place the vehicle in a warm area. Pull steadily on the top fabric. The vinyl will stretch back to its original size and the top can then be snapped into place. If temperature is 41°F (5°C) or below, do not attempt to put the top down or roll the rear or side curtains.

CAUTION!

WARNING!

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169

may scratch the window.

(5°C). Damage to the top may result.

Window scratches and wax build-up may result.

• Do not run a fabric top through an automatic car wash. • Do not lower the top when the temperature is below 41°F • Do not lower the top when the windows are dirty. Grit • Do not move your vehicle until the top has been either fully attached to the windshield frame, or fully lowered. • Do not lower the top with the windows installed. Win- • Refer to “Appearance Care for Fabric Top Models” in Section 7 of this manual. It contains important informa- tion on cleaning and caring for your vehicle’s fabric top. • Do not use any tools (screwdrivers, etc.) to pry or force any of the clamps, clips, or retainers securing the soft top. Do not force or pry the soft top framework when opening or closing. Damage to the top may result.

dow and top damage may occur.

• Do not drive vehicle with rear window curtain up unless side curtains are also open. Dangerous exhaust gases which can kill could enter the ve- hicle. • The fabric upper doors and fabric top are designed only for protection against the elements. Do not rely on them to contain occupants within the vehicle or to protect against injury during an accident. Remember, always wear seat belts.

170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Folding Down The Soft Top

1 — Header Bow 2 — 2–Bow 3 — 3–Bow 4 — 4–Bow 5 — Sail Panel

6 — Body Side Retainer 7 — Quarter Window 8 — Check Strap 9 — Front Retainer — Quarter Window 10 — Bottom Retainer — Quarter Window

11 — Plastic Retainer

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171

1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels

172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: Clean side and rear windows before removal to assist in preventing scratching during removal of the soft top. If zippers are difficult to operate due to road dust, etc., clean them with a mild soap solution and a small brush. Cleaning products are available through your authorized dealer. 1. If your vehicle has half-doors, remove each half-door window by opening the door and lifting the half-door window out. NOTE: Stow half-door windows carefully outside of the vehicle, never inside to avoid scratches. 2. Above the front of the rear door, place finger up into the cutout in the plastic retainer and pull down, rolling both the front and rear retainers out of the door frame. Repeat this on the other side.

3. Unclip and move the sun visors to the side.

4. Release the header latches and hooks from the loops on the windshield frame.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173

5. Open the swing gate. 6. Before unzipping the rear window, release the first 3 in (7.6 cm) of both sail panels from the channel. Remove the swing gate bar by pulling it straight rearward out of the swing gate brackets.

174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

• Unzip the rear window starting at the right lower corner of the window. Pull the zipper up, across the top and down to the left lower corner. Zipper pulls will stay on the rear window. Pull down on the rear window to disengage from the zipper on the top cover. Stow the windows carefully to avoid scratch- ing.

7. Undo the Velcro威 that runs along the top and rear edge of the side window. 8. Beginning from the rear lower corner, completely unzip the window.

9. Once unzipped, remove side window retainers from the door channel and body side channel. Repeat this step on the opposite side.

10. Finish releasing the sail panel retainers from the body side channel at the rear corners of the vehicle.

11. Fold the sail panels so that they rest on top of the soft top.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175

NOTE: When releasing the sail panel retainers, it is helpful to pull down on the rear roof bow.

176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

12. The swing gate brackets do not need to be removed unless the hard top is being installed. To remove the swing gate brackets, pull the front of the bracket forward while rolling the entire bracket back in towards the vehicle to disengage.

13. Grasp the front side bow behind the header, and lift the top.

14. Fold back the front section of the top, and gently rest the header on top of the rear portion of the deck.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

15. Fold the top material so that the plastic retainers form a “W” as shown. Enter the vehicle, and move the material into two folds.

178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

16. Release the side bows by pressing down on the latch above the front of the rear door. Push the top rearward to disengage. Repeat this step on the other side.

17. Grasp the folded side bows and slide the top along the door frame track to the rear door frame.

18. Before lowering the top, open the swing gate to prevent possible damage to the rear center high-mounted brake lamp. Gently slide the side bows off the door frame track and lower the top down into the vehicle.

20. Once the top is fully down, use the Velcro straps provided to secure the top to the vehicle by wrapping the strap around the side bows and through the slot on the body.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179

19. Tuck the fabric and the check straps between the bows as far inside as possible. This will keep any portion of the top from flapping outside of the vehicle.

21. Close the front header latches. 22. Remove door frames, Frame” in this section.

if desired. Refer to “Door

180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Putting Up The Soft Top

1 — Header Bow 2 — 2–Bow 3 — 3–Bow 4 — 4–Bow 5 — Sail Panel

6 — Body Side Retainer 7 — Quarter Window 8 — Check Strap 9 — Front Retainer — Quarter Window 10 — Bottom Retainer — Quarter Window

11 — Plastic Retainer

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181

1 — Zipper Start 2 — Zipper Finish 3 — Swing Gate Bar 4 — Swing Gate Brackets 5 — Sail Panels

182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: Be extremely careful when putting up the soft top to prevent the doors from getting scratched. It may be helpful to open the rear doors. 1. Install the door frames, if removed. Refer to “Door Frame” in this section. 2. Undo the straps used to secure the top in the down position and store in secure location. 3. Open the swing gate. 4. Grasp the folded side bows and lift to the top of the rear door frames.

5. Insert the slider feature of the knuckles into the door frame tracks and slide the top forward.

6. Ensure that the top locks into Sunrider locking mecha- nisms that are located above the front of the rear doors.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183

184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

7. Unclip and move the sun visors to the side. 8. Standing on the side of the vehicle, lift the top by the side bow until it rests on the windshield frame.

on the side bows above the front doors. They should cradle the tubing. Finally, make sure that the check strap (the long, woven strap reaching from the rear bow to the 2–bow) does not get entangled in any of the framework when unfolding the top.

9. Before attaching the header latches, be sure the top retainers above the doors do not get trapped between the top and the door frame. Also, make certain the feet at both ends of the 2–bow (forward most bow) seat properly

10. Open the header latches and engage the hook on each side onto the windshield loops (do not close the latches).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185

over the channel until it snaps onto the exterior part of the rail. To be properly located, the bracket must only be clipped to the shortened rail edge.

11. If the swing gate brackets were removed, install them by hooking the rear edge of the bracket on the interior side of the body channel. Then, rotate it rearward and

12. Move to the rear of the vehicle and gently pull the sail panels over the rear roof bow (4–bow).

186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

13. Partially install the sail panel retainers into the body side channel, leaving the last 3 in (7.6 cm) towards the rear window loose (on both sides). Pulling down on the rear roof bow (4–bow) will aid to reach the channel with the retainers.

14. To install the side windows, affix the window tem- porarily by attaching to the Velcro威 in the upper rear corner. Start the zipper but close only about 1 in (2.5 cm).

15. Insert the front retainer of the window into the door channel, making sure the retainer is fully seated and properly positioned on the door frame. Failure to do so can result in wind and water leaks or damage to the window.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187

16. Continue closing the zipper only along the top edge of the window.

188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

17. Insert the retainer along the bottom edge of the window into the bottom side channel, beginning at the front and working to the rear of the vehicle. Finish by closing the zipper completely and attaching the Velcro威 along the top and rear of the window. Repeat this step for the opposite side.

18. Locate the black swing gate bar. Slide the swing gate bar over the receiver at the bottom inside of the rear window. The spongy part of the seal should be down and pointed outward to seal with the swing gate when closed.

19. Install the rear window by starting both zipper ends at the lower left corner of the rear window opening. Ensure that the zippers are properly started and aligned before zipping to prevent damage.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189

21. Grasp the swing gate bar and position it into the swing gate brackets.

20. Run the first zipper fully around to the right side of the window.

22. Complete the installation of the sail panel by insert- ing the rest of the retainer into the body channel.

190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

23. Open the doors and insert the top retainers into the channels in the door frame above the doors, starting at the front and working toward the rear of the vehicle.

24. Ensure plastic retainer is tucked in properly at B-pillar, not pinching the seal.

25. Close the header latches and return the sun visors to their secured position.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191

FOLDING WINDSHIELD The fold-down windshield and removable side bars on your vehicle are structural elements that can provide some protection in some accidents. The windshield also provides some protection against weather, road debris and intrusion of small branches and other objects. Do not drive your vehicle on-road with the windshield down and the side bars removed as you lose the protec- tion these structural elements can provide. If required for certain off-road uses, the side bars can be removed and the windshield folded down. However, the protection afforded by these features is then lost. If you remove the side bars and fold down the windshield, drive slowly and cautiously. It is recommended that the speed of the vehicle be limited to 10 mph (16 km/h), with low range operation preferred, if you are driving off-road with the windshield folded down.

192 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Raise the windshield and reinstall the side bars as soon as the task that required their removal is completed and before you return to on-road driving. Both you and your passenger should wear seat belts at all times, on-road and off-road, regardless of whether the windshield is raised or folded down. Outside rearview mirrors are mounted on the doors. If you choose to remove the doors, see your authorized dealer for a replacement cowl-mounted outside mirror. Federal law requires outside mirrors on vehicles for on-road use.

WARNING!

shield down.

times when the windshield is down.

securely fastened, either up or down.

Carefully follow these warnings to help protect against personal injury: • Do not drive your vehicle on-road with the wind- • Do not drive your vehicle unless the windshield is • Eye protection, such as goggles, should be worn at all • Be sure that you carefully follow the instructions for raising the windshield. Make sure that the folding windshield, windshield wipers, side bars, and all associated hardware and fasteners are correctly and tightly assembled before driving your vehicle. Failure to follow these instructions may prevent your vehicle from providing you and your passengers protection in some accidents. • If you remove the doors, store them outside the vehicle. In the event of an accident, a loose door may cause personal injury.

Lowering The Windshield And Removing Side Bars

1. Lower the fabric top or remove the hard top following the instructions in this manual. NOTE: To assist in properly reinstalling side bars, mark the original locations prior to removing. 2. Remove the two top hex bolts (13 mm), and the one side hex bolt (13 mm) visible through the trim (Do not remove plastic corner trim, sun visor bolts, or sport bar covering).

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 193

3. Open sport bar Velcro covering. 4. Remove the one hex bolt (13 mm) visible through the plastic trim on bottom side of side bar, one hex bolt (13
mm) on the side of the side bar, and one hex bolt (13 mm) on top of the side bar.

194 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

NOTE: Pull side bar out horizontally when removing.

CAUTION!

Do not remove the head impact foam from the side bars, as damage to the foam may result.

NOTE: Store all of the mounting bolts in their original threaded holes and tighten for safekeeping. 5. Remove side bar assembly, and reattach sport bar Velcro威 covering. 6. To safely store the side bars in your vehicle, use four cinch straps (available from your authorized dealer). Attach the straps through the slots located on the floor behind the folded rear seat at the front of the storage bin cover.

WARNING!

You or others could be injured if you carry the side bars loose in your vehicle. Remove the side bars from the vehicle or securely store them as described or they may cause personal injury if an accident occurs. See your authorized dealer for the cinch straps.

7. Remove the windshield wiper arms by first pulling the wiper away from the windshield and out to the “lock” position. Unsnap the wiper arm nut caps, and remove retaining nuts. Lift the wiper arms off and store in center console or securely behind the rear seat. 8. Remove the lower windshield plates by removing the six black round-headed Torx威 head screws (using a #40
Torx威 head driver) on each side of the base of the windshield.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 195

it contacts the

9. Lower the windshield gently until rubber hood bumpers. 10. Secure the windshield by passing a cinch strap through the footman hoop on the center of the hood and on the center of the windshield frame. Tighten the strap to secure the windshield in place.

196 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Raising The Windshield And Replacing Side Bars

1. Raise the windshield. 2. Loosely attach rear of side bar to sport bar. Refer to Step 4 of “Lowering Windshield And Removing Side Bars” earlier in this section.

3. Attach front of side bar to windshield frame. • Install top two hex bolts (13 mm) first, then lower side hex bolt (13 mm). Lower side bolt will not align until top two bolts are installed.

• Reattach sport bar Velcro威 covering.

4. Tighten all side bar attachment bolts.

5. Install the lower windshield plates with the six black round-headed Torx威 head screws (using a #40 Torx威 head driver) on each side of the base of the windshield.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 197

REAR WINDOW FEATURES — HARD TOP ONLY

Rear Window Wiper/Washer — If Equipped A rotary ring switch on the control lever (located on the right side of the steering column), controls operation of the rear wiper/washer function. Rotating the center of the switch up to the “On” position will activate the wiper. Rotating the switch ring beyond the “On” or “Off” position will activate the rear washer. The wash pump will continue to operate as long as the lever or ring is engaged. Upon release, the wipers will cycle three times before returning to the set position.

6. Reinstall wiper arms.

198 UNDERSTANDING THE FEATURES OF YOUR VEHICLE

Windshield Wiper/Washer Switch

If the rear wiper is operating when the ignition is turned OFF, the wiper will automatically return to the “Park” position. When the vehicle is restarted, the wiper will resume function at whichever position the switch is set at.

Adding Washer Fluid The fluid reservoir for the windshield washers and the rear window washer is shared. It is located in the front of the engine compartment, and should be checked for fluid level at regular intervals. Fill the reservoir with wind- shield washer solvent (not radiator antifreeze) and oper- ate the system for a few seconds to flush out the residual water. Rear Window Defroster — If Equipped

The pushbutton is located on the bottom right side of the blower control knob. Press this button to turn on the rear window defroster. An amber light shows that the defroster is on.

The defroster will automatically turn off after about ten minutes. For five more minutes of operation, press the switch again. To prevent excessive battery drain, use the defroster only when the engine is operating.

UNDERSTANDING THE FEATURES OF YOUR VEHICLE 199

CAUTION!

Use care when washing the inside of the rear window to prevent damage to heating elements. Use a soft cloth and a mild washing solution, wiping parallel to the heating elements. Also, keep all objects a safe distance from the window to prevent damaging the heating elements.

UNDERSTANDING YOUR INSTRUMENT PANEL

CONTENTS

䡵 Instrument Panel And Controls . . . . . . . . . . . . . 204
䡵 Instrument Cluster . . . . . . . . . . . . . . . . . . . . . . 205
䡵 Instrument Cluster Description . . . . . . . . . . . . . 206
䡵 Compass And Trip Computer — If Equipped . . . 215
▫ Control Buttons . . . . . . . . . . . . . . . . . . . . . . 216
▫ Trip Conditions . . . . . . . . . . . . . . . . . . . . . . . 216
▫ Compass Temperature Display . . . . . . . . . . . . 217
䡵 Radio General Information . . . . . . . . . . . . . . . . 220
▫ Radio Broadcast Signals . . . . . . . . . . . . . . . . . 220

▫ Two Types Of Signals . . . . . . . . . . . . . . . . . . 221
▫ Electrical Disturbances . . . . . . . . . . . . . . . . . . 221
▫ AM Reception . . . . . . . . . . . . . . . . . . . . . . . 221
▫ FM Reception . . . . . . . . . . . . . . . . . . . . . . . . 221

䡵 Sales Code RES — AM/FM Stereo Radio With

CD Player (MP3 AUX Jack) . . . . . . . . . . . . . . . . 222
▫ Operating Instructions - Radio Mode . . . . . . . 222
▫ Operation Instructions - CD Mode For CD

And MP3 Audio Play . . . . . . . . . . . . . . . . . . 228
. . . . . . . . . . . . . 230

▫ Notes On Playing MP3 Files

202 UNDERSTANDING YOUR INSTRUMENT PANEL

▫ List Button (CD Mode For MP3 Play) . . . . . . . 233
▫ Info Button (CD Mode For MP3 Play) . . . . . . . 233

䡵 Sales Code REQ — AM/FM Stereo Radio

And 6–Disc CD/DVD Changer (MP3/WMA AUX Jack) . . . . . . . . . . . . . . . . . . 234
▫ Operating Instructions - Radio Mode . . . . . . . 235
▫ Operation Instructions - (Disc Mode For CD

And MP3/WMA Audio Play, DVD-Video) . . . . 243
▫ Notes On Playing MP3/WMA Files . . . . . . . . 245
▫ List Button

(Disc Mode For MP3/WMA Play) . . . . . . . . . . 247

▫ Info Button

(Disc Mode For MP3/WMA Play) . . . . . . . . . . 247

䡵 Sales Code RER — Multimedia System

— If Equipped . . . . . . . . . . . . . . . . . . . . . . . . . 250

▫ Operating Instructions — Satellite Radio . . . . . 251
▫ Operating Instructions — Hands-Free

Communication (UConnect威) (If Equipped) . . . 251
▫ Clock Setting Procedure . . . . . . . . . . . . . . . . . 251

䡵 Satellite Radio — If Equipped

. . . . . . . . . 253
(REN/REQ/RER/RES Radios Only) ▫ System Activation . . . . . . . . . . . . . . . . . . . . . 254
▫ Electronic Serial Number/Sirius Identification

Number (ESN/SID) . . . . . . . . . . . . . . . . . . . . 254
▫ Selecting Satellite Mode . . . . . . . . . . . . . . . . . 255
▫ Satellite Antenna . . . . . . . . . . . . . . . . . . . . . . 255
▫ Reception Quality . . . . . . . . . . . . . . . . . . . . . 255
▫ Operating Instructions - Satellite Mode . . . . . . 255

▫ Operating Instructions - Hands-Free Phone

(If Equipped)

. . . . . . . . . . . . . . . . . . . . . . . . 257

▫ Operating Instructions - Video Entertainment

System (VES威) (If Equipped)

. . . . . . . . . . . . . 258
䡵 CD/DVD Disc Maintenance . . . . . . . . . . . . . . . 258
䡵 Radio Operation And Cellular Phones . . . . . . . . 258
䡵 Climate Controls . . . . . . . . . . . . . . . . . . . . . . . 259

UNDERSTANDING YOUR INSTRUMENT PANEL 203

▫ Manual Heater Only . . . . . . . . . . . . . . . . . . . 259
▫ Manual Air Conditioning And Heating System

— If Equipped . . . . . . . . . . . . . . . . . . . . . . . 261
▫ Air Conditioning . . . . . . . . . . . . . . . . . . . . . 264
▫ Operating Tips . . . . . . . . . . . . . . . . . . . . . . . 265

204 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT PANEL AND CONTROLS

1 — Air Outlet 2 — Instrument Cluster 3 — Horn 4 — Radio 5 — Glove Box

6 — Climate Controls 7 — Power Outlet 8 — Lower Switch Bank 9 — Auxiliary Power Outlet

INSTRUMENT CLUSTER

UNDERSTANDING YOUR INSTRUMENT PANEL 205

206 UNDERSTANDING YOUR INSTRUMENT PANEL

INSTRUMENT CLUSTER DESCRIPTION Your vehicle is equipped with the instrument cluster described on the following pages. 1. Fuel Gauge The pointer shows the level of fuel in the fuel tank. NOTE: When the ignition switch is turned to OFF, the fuel gauge, voltmeter, oil pressure and temperature gauges may not show accurate readings. When the engine is not running, turn the ignition switch to ON to obtain accurate readings. 2. Charging System Warning Light

This light shows the status of the electrical charg- ing system. The light should come on for three seconds when the ignition is first turned ON. If the light comes back on immediately or comes on while driving, it means that there is a problem with the charging system or the battery is low. Also, a chime will sound if the light comes back on. See your authorized dealer immediately.

3. Front Fog Light Indicator Light — If Equipped

This light shows when the front fog lights are on.

4. Low Fuel Warning Light

When the fuel level reaches approximately 2.8 gal (10.6L) this light will turn on and a single chime will sound.

5. Speedometer Indicates vehicle speed. 6. Front Axle Lock Indicator Light — If Equipped

Indicates when the front axle lock has been activated.

7. Seat Belt Indicator Light

A warning chime and an indicator light will alert you to buckle the seat belts. When the belt is buckled, the chime will stop, but the light will stay

on until it times out (about six seconds). 8. Turn Signal Indicator Lights

The arrows will flash with the exterior turn signals when the turn signal lever is operated. A tone will chime if the turn signals are left on for more than 1 mi (2
km). 9. Oil Pressure Warning Light

Shows low engine oil pressure. The light will come on and remain on when the ignition switch is turned from the OFF to the ON position, and the light will turn off after the engine is started. If the bulb does not come on, have the system checked by your autho- rized dealer.

UNDERSTANDING YOUR INSTRUMENT PANEL 207

If the warning light comes on and remains on while driving, stop the vehicle and shut off the engine. DO NOT OPERATE THE VEHICLE UNTIL THE CAUSE IS CORRECTED. Also, a single chime will sound. 10. High Beam Indicator Light

This light shows that the headlights are on high beam. Push the multifunction control lever away from you to switch the headlights to high beam. Pull the lever towards you to switch the headlights back to low beam. If the driver’s door is open, and the headlights or park lights are left on, the High Beam Indicator Light will remain illuminated and a chime will sound. 11. Brake Warning Light

After the ignition is turned on, this light illumi- nates to indicate function check at vehicle start- up. It also indicates if the parking brake is applied. If the light stays on when the parking brake is

208 UNDERSTANDING YOUR INSTRUMENT PANEL

off, it indicates a possible brake system fluid leak or low pressure level, see your authorized dealer immediately. If the parking brake is applied and the vehicle is in motion, the Brake Warning Light will “flash” and a chime will sound. The operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON position. The light should illuminate for approxi- mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. 12. Anti-Lock (ABS) Warning Light

After the ignition is turned on, this light illumi- nates to indicate function check at vehicle start-up. If the light remains on after start-up or comes on and stays on at road speeds, it may indicate that the ABS has

detected a malfunction or has become inoperative. The system reverts to standard non-anti-lock brakes. If both the Brake Warning Light and the ABS Warning Light are on, see your authorized dealer immediately. Refer to “Anti-Lock Brake System” in Section 5 of this manual. 13. Airbag Warning Light

This indicator lights and remains lit for six to eight seconds when the ignition is first turned on. If the light does not come on for six to eight seconds, stays on or comes on while driving, have the airbag system checked by an authorized dealer. 14. Rear Axle Lock Indicator Light — If Equipped

This light indicates when the rear axle lock has been activated.

15. Tachometer This light indicates the engine speed in revolutions per minute (RPM).

CAUTION!

Do not operate the engine with the tachometer pointer in the red area. Engine damage will occur.

16. Engine Coolant Temperature Warning Light

This light warns of an overheated engine condi- tion. If the engine is critically hot, a warning chime will sound 10 times. After the chime turns off, the engine will still be critically hot until the light goes out. 17. Sentry Key威/Security Alarm Indicator Light — If Equipped Refer to “Sentry Key威 Immobilizer System” or “Vehicle Security Alarm” in Section 2 of this manual.

UNDERSTANDING YOUR INSTRUMENT PANEL 209

18. Coolant Temperature Gauge

Indicates engine coolant temperature. The red zone to the far right indicates possible overheat- ing. Seek your authorized dealer immediately if the gauge operates in the red zone. On U.S. vehicles, the temperature is indicated in degrees fahrenheit; and on Canadian vehicles in degrees centigrade. 19. Cruise Indicator Light

This light shows when the electronic speed control system is turned on.

20. 4WD Indicator Light — If Equipped

This light alerts the driver that the vehicle is in the four-wheel drive mode, and the front and rear driveshafts are mechanically locked to- gether forcing the front and rear wheels to

rotate at the same speed.

210 UNDERSTANDING YOUR INSTRUMENT PANEL

21. Odometer/Trip Odometer Reset Button Press this button to change the display from odometer to either of two trip odometer settings. Trip A or Trip B will appear when in the trip odometer mode. Press and hold the button for two seconds to reset the trip odometer to 0
miles or kilometers. The odometer must be in trip mode to reset. 22. Transmission Range Indicator This display indicator shows the automatic transmission gear selection. 23. Tire Pressure Monitoring Telltale Light

Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the

vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accord- ingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a signifi- cantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale.

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subse- quent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the sys- tem may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replace- ment or alternate tires and wheels allow the TPMS to continue to function properly.

UNDERSTANDING YOUR INSTRUMENT PANEL 211

CAUTION!

The TPMS has been optimized for the original equipment tires and wheels. TPMS pressures and warning have been established for the tire size equipped on your vehicle. Undesirable system opera- tion or sensor damage may result when using re- placement equipment that is not of the same size, type, and/or style. After-market wheels can cause sensor damage. Do not use aftermarket tire sealants or balance beads if your vehicle is equipped with a TPMS, as damage to the sensors may result.

24. Odometer/Trip Odometer The odometer shows the total distance the vehicle has been driven.

212 UNDERSTANDING YOUR INSTRUMENT PANEL

U.S. federal regulations require that upon transfer of vehicle ownership, the seller certify to the purchaser the correct mileage that the vehicle has been driven. There- fore, if the odometer reading is changed during repair or replacement, be sure to keep a record of the reading before and after the service so the correct mileage can be determined. Vehicle Warning Messages When the appropriate conditions exist, messages such as “door” (indicates that a door(s) may be ajar), “gATE” (if the swing gate is open or ajar), “gASCAP” (which indicates that your gas cap is possibly loose or damaged), ⬙CHANgE OIL” (indicates that the engine oil should be changed), “ESPOFF” (indicates that ESP is turned off), and “noFUSE” (indicates that the Ignition Off Draw (IOD) fuse is removed from the Integrated Power Mod- ule), will display in the odometer.

Change Oil Message Your vehicle is equipped with an engine oil change indicator system. The “CHANgE OIL” message will flash in the instrument cluster odometer for approximately 12
seconds after a single chime has sounded to indicate the next scheduled oil change interval. The engine oil change indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon your personal driving style. Unless reset, this message will continue to display each time you turn the ignition switch to the ON/RUN position. To turn off the message temporarily, press and release the Trip Odometer button on the instrument cluster. To reset the oil change indicator system (after performing the scheduled maintenance) refer to the fol- lowing procedure.

1. Turn the ignition switch to the ON position (Do not start the engine).

2. Fully depress the accelerator pedal slowly three times within 10 seconds. 3. Turn the ignition switch to the OFF/LOCK position. If the indicator message illuminates when you NOTE: start the vehicle, the oil change indicator system did not reset. If necessary repeat this procedure. 25. Malfunction Indicator Light

This light is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. The light will illuminate when the ignition is in the ON position before engine start. If the bulb does not come on when turning the key from OFF to ON, have the condition checked promptly. Certain conditions such as a loose or missing gas cap, poor quality fuel, etc. may illuminate the light after engine start. The vehicle should be serviced if the light

UNDERSTANDING YOUR INSTRUMENT PANEL 213

stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the Malfunction Indicator Light may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced as soon as possible if this occurs. 26. Electronic Stability Program (ESP) Indicator Light/Traction Control System (TCS) Indicator Light

This indicator light starts to flash as soon as the tires lose traction and the ESP system becomes active. The ESP/TCS Indicator Light also flashes when TCS is active. If the ESP/TCS Indicator Light begins to flash during acceleration, ease up on the accelerator and apply as little throttle as possible. Be sure to adapt your speed and driving to the prevailing road conditions. The ESP/TCS Indicator Light

214 UNDERSTANDING YOUR INSTRUMENT PANEL

will flash anytime the ESP or TCS is active and helping to improve vehicle stability. If the ESP/TCS Indicator Light is on solid, the ESP system has been turned off by the driver or a temporary condition exists that will not allow full ESP function. 27. O/D (Overdrive) Off Indicator Light

This light will illuminate when the O/D OFF button has been selected. The O/D OFF button is

located on the center console. 28. Sway Bar Indicator Light — If Equipped

This light will illuminate when the front sway bar is disconnected.

29. Electronic Stability Program (ESP)/Brake Assist System (BAS) Warning Light

The ESP/BAS Warning Light in the instrument cluster comes on when the ignition switch is turned to the ON position. The light should go

out with the engine running. If the ESP/BAS Warning Light comes on continuously with the engine running, a malfunction has been detected in either the ESP or the BAS system. If this light stays illuminated, have the ESP and BAS checked at your authorized dealer as soon as possible. Refer to “Electronic Brake Control System” in Section 3 for more information. 30. Electronic Throttle Control (ETC) Warning Light — If Equipped

This light informs you of a problem with the Electronic Throttle Control System. If a prob- lem is detected while the engine is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition key when the vehicle is safely and completely stopped and the shift lever is placed in the PARK position. The light should turn off. If the light remains on with the engine running, your vehicle will usually be drivable, however, see your authorized dealer for service as soon as possible.

UNDERSTANDING YOUR INSTRUMENT PANEL 215

COMPASS AND TRIP COMPUTER — IF EQUIPPED This feature, located on the instrument cluster (speedom- eter and tachometer), displays information on outside temperature, compass direction, and trip information.

If the light continues to flash when the engine is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing. The light will come on when the ignition is first turned on and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by your autho- rized dealer. 31. Compass/Mini-Trip Computer Display — If Equipped When the appropriate conditions exist, this display shows the Mini-Trip Computer messages. Refer to “Mini- Trip Computer” later in this section. 32. Compass/Mini-Trip Computer Button—If Equipped Press this button to switch between the different func- tions.

216 UNDERSTANDING YOUR INSTRUMENT PANEL

Control Buttons Press and release the left button (on the instrument cluster) to access the computer displays. Press and hold the left button (on the instrument cluster) for two to three seconds to switch from English to Metric displays. Reset Press and hold the right button (on the instrument cluster) while function is being displayed to reset. The following trip conditions can be reset: • AVG ECO (changes to present fuel economy) • ET

Trip Conditions

Average Fuel Economy (AVG ECO) This display shows the average fuel economy since the last reset. Estimated Range (DTE) This display shows the estimated distance that can be traveled with the fuel remaining in the tank. This esti- mated distance is based on the most recent trip informa- tion: (Average Fuel Economy) x (Fuel Remaining) This display cannot be reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset.

Trip Odometer (ODO) This display shows the distance traveled since the last reset. Press and release the right button (on the instru- ment cluster) to switch from odometer, to Trip A or Trip B. Press and hold the right button while the odometer/ trip odometer is displayed to reset. Trip A Shows the total distance traveled for Trip A since the last reset. Trip B Shows the total distance traveled for Trip B since the last reset. Compass Temperature Display This display provides the outside temperature and one of eight compass readings to indicate the direction the vehicle is facing.

UNDERSTANDING YOUR INSTRUMENT PANEL 217

WARNING!

Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.

Compass Calibration The Automatic Compass Calibration feature eliminates the need for operator intervention under normal condi- tions. If the CAL indicator is lit, the compass needs to be calibrated. A good calibration requires a level surface and an environment free of large metal objects such as large buildings, bridges, underground cables, railroad tracks, etc.

218 UNDERSTANDING YOUR INSTRUMENT PANEL

NOTE: Magnetic materials should be kept away from the top of the instrument panel above the radio. This is where the compass sensor is located. Automatic Compass Calibration The self-calibrating feature of the compass eliminates the need to calibrate the compass for normal conditions. During a short initial period, the compass may appear erratic and the CAL symbol will appear (blinking) on the display. After the vehicle has completed at least one complete circle under 5 mph (8 km/h) in an area free from large metal objects, calibration will be complete when the CAL symbol is extinguished. After initial calibration, the compass will continue to automatically update this calibration whenever the ve- hicle is in motion.

Manual Compass Calibration

NOTE: Before attempting a manual compass calibra- tion, the engine must be running and the transmission in the PARK position (if equipped). If the compass seems in error or erratic, you may wish to manually recalibrate the compass. To manually calibrate the compass, you must first enter the variance mode. Press and hold the left button (located on the instrument cluster) for approximately 10 seconds to enter the vari- ance mode, and release the button when the VAR (Com- pass Variance) symbol appears. The current variance value will also be displayed. Once in the variance mode, it is necessary to release the button, and then press and hold it again (approximately 10 seconds) until CAL is displayed (solid, not blinking). Manual compass calibra- tion has been initiated. Drive the vehicle slowly in one or more circles under 5 mph (8 km/h) in an area free from large metal objects until the CAL symbol is extinguished.

UNDERSTANDING YOUR INSTRUMENT PANEL 219

to increment the zone. The default is Zone 8. After Zone 15, the values will wrap around to Zone 1. When the correct zone is displayed (per the Compass Variance Zone Map) for the zone that the vehicle is located in, wait for about five seconds, then the trip computer will store the variance value in memory and the compass will resume normal operation. NOTE: The U.S./Metric display will change from En- glish to Metric or Metric to English before the VAR symbol appears, however, it will revert back to its original setting after programming the compass func- tions.

is no longer displayed,

When the CAL symbol the compass is calibrated and should display correct head- ings. Verify proper calibration by checking North (N), South (S), East (E), and West (W). If the compass does not appear accurate, repeat the calibration procedure in an- other area. Compass Variance (VAR) Variance is the difference between magnetic North and geographic North. For proper compass function, the correct variance zone must be set. Setting the Compass Variance Refer to the variance map for the correct compass vari- ance zone. To check the variance zone, the ignition must be ON. Press and hold the left button (located on the instrument cluster) for approximately 10 seconds to enter the variance mode and release the button when the VAR symbol appears. The current variance value will also be displayed. To change the zone, press the left button once

220 UNDERSTANDING YOUR INSTRUMENT PANEL

Outside Temperature If the outside temperature is more than 131°F (55°C), the display will show 131°F (55°C). When the outside tem- perature is less than ⫺40°F (⫺40°C), the display will show ⫺40°F (⫺40°C).

RADIO GENERAL INFORMATION

Radio Broadcast Signals The radio will provide excellent reception under most operating conditions. Like any system, however, automo- tive radios have performance limitations, due to mobile operation and natural phenomena, which might lead you to believe your sound system is malfunctioning. To help you understand and save you concern about these “ap- parent” malfunctions, you must understand a point or two about the transmission and reception of radio sig- nals.

UNDERSTANDING YOUR INSTRUMENT PANEL 221

FM Reception Because FM transmission is based on frequency varia- tions, interference that consists of amplitude variations can be filtered out, leaving the reception relatively clear, which is the major feature of FM radio. NOTE: The radio, steering wheel radio controls (if equipped), and six-disc CD/DVD changer (if equipped) will remain active for up to 10 minutes after the ignition switch has been turned OFF. Opening a vehicle front door will cancel this feature.

Two Types of Signals There are two basic types of radio signals: AM or Amplitude Modulation, in which the transmitted sound causes the amplitude, or height, of the radio waves to vary; and FM or Frequency Modulation, in which the frequency of the wave is varied to carry the sound. Electrical Disturbances Radio waves may pick up electrical disturbances during transmission. They mainly affect the wave amplitude, and thus remain a part of the AM reception. They interfere very little with the frequency variations that carry the FM signal. AM Reception AM sound is based on wave amplitude, so AM reception can be disrupted by such things as lightning, power lines and neon signs.

222 UNDERSTANDING YOUR INSTRUMENT PANEL

SALES CODE RES — AM/FM STEREO RADIO WITH CD PLAYER (MP3 AUX JACK)

NOTE: The radio sales code is located on the lower right side of your radio faceplate.

RES Radio (Non-Satellite Model Shown - With Satellite

Similar)

Operating Instructions - Radio Mode

NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Push the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it. When the audio system is turned on, the sound will be set at the same volume level as last played. SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch

to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station in AM or FM frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time. Voice Recognition System (Radio) — If Equipped Refer to “Voice Recognition System (VR)” in Section 3. Voice Recognition Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3.

UNDERSTANDING YOUR INSTRUMENT PANEL 223

If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. Phone Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display. In AM or FM mode, pressing the TIME button will switch between the time and frequency displays.

224 UNDERSTANDING YOUR INSTRUMENT PANEL

Clock Setting Procedure 1. Press and hold the TIME button, until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob. 3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button. For vehicles equipped with satellite radio, press the SETUP button, use the TUNE/SCROLL control to select SET CLOCK, and then follow the above procedure,

starting at Step 2. For vehicles not equipped with satellite radio, press the SETUP button and then follow the above procedure, starting at Step 2. INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only). RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in either AM or FM frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency.

Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones. Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display. Turn the TUNE/ SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers.

UNDERSTANDING YOUR INSTRUMENT PANEL 225

Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade. MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast Music Type information.

226 UNDERSTANDING YOUR INSTRUMENT PANEL

Toggle the MUSIC TYPE button to select the following format types:

Program Type

No program type or

undefined Adult Hits Classical

Classic Rock

College Country

Foreign Language

Information

Jazz News

Nostalgia

Oldies

16-Digit Character

Display

None

Adlt Hit Classicl Cls Rock College Country Language

Inform Jazz News

Nostalga Oldies

Program Type

Personality

Public

Rhythm and Blues Religious Music Religious Talk

Rock Soft

Soft Rock

Soft Rhythm and Blues

Sports Talk Top 40
Weather

16-Digit Character

Display Persnlty Public R & B

Rel Musc Rel Talk

Rock Soft

Soft Rck Soft R&B

Sports Talk Top 40
Weather

By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency

station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items: • Set Clock — Pressing the SELECT button will allow you to set the clock. Turn the TUNE/SCROLL control knob to adjust the hours and then press and turn the TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes.

AM and FM Buttons Press the buttons to select AM or FM modes.

UNDERSTANDING YOUR INSTRUMENT PANEL 227

SET Button — To Set the Pushbutton Memory When you are receiving a station that you wish to commit to pushbutton memory, press the SET button. The symbol SET 1 will now show in the display window. Select the button (1 to 6) you wish to lock onto this station and press and release that button. If a button is not selected within five seconds after pressing the SET but- ton, the station will continue to play but will not be stored into pushbutton memory. You may add a second station to each pushbutton by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM. This allows a total of 12 AM and 12 FM stations to be stored into pushbutton memory. The sta- tions stored in SET 2 memory can be selected by pressing the pushbutton twice.

228 UNDERSTANDING YOUR INSTRUMENT PANEL

Every time a preset button is used, a corresponding button number will display. Buttons 1 - 6
These buttons tune the radio to the stations that you commit to pushbutton memory (12 AM and 12 FM stations). DISC Button Pressing the DISC button will allow you to switch from AM/FM modes to Disc modes. Operation Instructions - CD MODE for CD and MP3 Audio Play

NOTE: The ignition switch must be in the ON or ACC position to operate the radio. NOTE: This radio is capable of playing compact discs (CD), recordable compact discs (CD-R), rewritable com- pact discs (CD-RW), compact discs with MP3 tracks and multisession compact discs with CD and MP3 tracks.

Inserting Compact Disc(s) Gently insert one CD into the CD player with the CD label facing up. The CD will automatically be pulled into the CD player and the CD icon will illuminate on the radio display. If a CD does not go into the slot more than an inch (2.5 cm), a disc may already be loaded and must be ejected before a new disc can be loaded. If you insert a disc with the ignition ON and the radio ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1.

CAUTION!

away and jam the player mechanism.

• This CD player will accept 4–3/4 in (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. • Do not use adhesive labels. These labels can peel • RES is a single CD player. Do not attempt to insert • Dual-media disc types (one side is a DVD, the other side is a CD) should not be used, and they can cause damage to the player.

a second CD if one is already loaded.

EJECT Button - Ejecting a CD

Press the EJECT button to eject the CD.

UNDERSTANDING YOUR INSTRUMENT PANEL 229

If you have ejected a disc and have not removed it within 10 seconds, it will be reloaded. If the CD is not removed, the radio will reinsert the CD but will not play it. A disc can be ejected with the radio and ignition OFF. NOTE: Ejecting with ignition OFF is not allowed on convertible or soft-top models (if equipped). SEEK Button Press the right SEEK button for the next selection on the CD. Press the left SEEK button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first second of the current selection. Pressing and holding the SEEK button will allow faster scrolling through the tracks in CD, MP3 modes. SCAN Button Press the SCAN button to scan through each track on the CD currently playing.

230 UNDERSTANDING YOUR INSTRUMENT PANEL

TIME Button Press this button to change the display from a large CD playing time display to a small CD playing time display. RW/FF Press the RW button to stop the CD at the beginning of the current CD track/title. Press and hold FF (Fast Forward) and the CD player will begin to fast forward until FF is released or RW or another CD button is pressed. The RW (Reverse) button works in a similar manner. AM or FM Button Switches the AM or FM radio to the opposite radio mode. RND Button (Random Play Button) Press this button while the CD is playing to activate Random Play. This feature plays the selections on the compact disc in random order to provide an interesting change of pace.

Press the right SEEK button to move to the next ran- domly selected track. Press the RND button a second time to stop Random Play. Notes On Playing MP3 Files The radio can play MP3 files; however, acceptable MP3
file recording media and formats are limited. When writing MP3 files, pay attention to the following restric- tions. Supported Media (Disc Types) The MP3 file recording media supported by the radio are CDDA, CD-R, CD-RW, MP3, and CDDA+MP3. Supported Medium Formats (File Systems) The medium formats supported by the radio are ISO 9660
Level 1 and Level 2 and includes the Joliet extension. When reading discs recorded using formats other than ISO 9660 Level 1 and Level 2, the radio may fail to read

files properly and may be unable to play the file nor- mally. UDF and Apple HFS formats are not supported. The radio uses the following limits for file systems: • Maximum number of folder levels: 8
• Maximum number of files: 255
• Maximum number of folders. (The radio display of file names and folder names is limited. For large numbers of files and/or folders, the radio may be unable to display the file name and folder name and will assign a number instead. With a maximum number of files, exceeding 20 folders will result in this display. With in this 200 files, exceeding 50 folders will result display.) • Maximum number of characters in file/folder names: • Level 1: 12 (including a separator ⬙.⬙ and a three-

character extension)

UNDERSTANDING YOUR INSTRUMENT PANEL 231

• Level 2: 31 (including a separator ⬙.⬙ and a three-

character extension)

Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal CD audio tracks and computer files (including MP3 files). Discs created with an option such as ⬙keep disc open after writing⬙ are most likely multisession discs. The use of multisession for CD audio or MP3 playback may result in longer disc loading times. Supported MP3 File Formats The radio will recognize only files with the *.MP3 exten- sion as MP3 files. Non-MP3 files named with the *.MP3
extension may cause playback problems. The radio is designed to recognize the file as an invalid MP3 and will not play the file. When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the following table are supported. In addition, variable bit

232 UNDERSTANDING YOUR INSTRUMENT PANEL

rates (VBR) are also supported. The majority of MP3 files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or VBR bit rates.

MPEG Specifi-

cation

Sampling Fre- quency (kHz)

MPEG-1 Audio

Layer 3

48, 44.1, 32

MPEG-2 Audio

Layer 3

24, 22.05, 16

Bit Rate (kbps)

320, 256, 224, 192, 160, 128, 112, 96, 80, 64, 56, 48, 40, 32
160, 128, 144, 112, 96, 80, 64, 56, 48, 40, 32, 24,

16, 8

ID3 Tag information for artist, song title, and album title are supported for version 1 ID3 tags. ID3 version 2 is not supported by the radios. Playlist files are not supported. MP3 Pro files are not supported.

Playback of MP3 Files When a medium containing MP3 data is loaded, the radio checks all files on the medium. If the medium contains a lot of folders or files, the radio will take more time to start playing the MP3 files. Loading times for playback of MP3 files may be affected by the following: • Media - CD-RW media may take longer to load than • Medium formats - Multisession discs may take longer • Number of files and folders - Loading times will

to load than non-multisession discs

CD-R media

increase with more files and folders

To increase the speed of disc loading, it is recommended to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option before writing to the disc.

LIST Button (CD Mode for MP3 Play) Pressing the LIST button will bring up a list of all folders on the disc. Scrolling up or down the list is done by turning the TUNE/SCROLL control knob. Selecting a folder by pressing the TUNE/SCROLL control knob will begin playing the files contained in that folder (or the next folder in sequence if the selection does not contain playable files). The folder list will time out after five seconds. INFO Button (CD Mode for MP3 Play) Pressing the INFO button repeatedly will scroll through the following TAG information: Song Title, Artist, File Name, and Folder Name (if available). Press the INFO button once more to return to ⬙elapsed time⬙ priority mode.

UNDERSTANDING YOUR INSTRUMENT PANEL 233

Press and hold the INFO button for three seconds or more and the radio will display song titles for each file. Press and hold the INFO button again for three seconds to return to ⬙elapsed time⬙ display. Operation Instructions - Auxiliary Mode The auxiliary (AUX) jack is an audio input jack, which allows the user to plug in a portable device such as an MP3 player, or cassette player, and utilize the vehicle’s audio system to amplify the source and play through the vehicle speakers. Pressing the AUX button will change the mode to auxil- iary device if the AUX jack is connected. NOTE: The AUX device must be turned on and the device’s volume set to proper level. If the AUX audio is not loud enough, turn the device’s volume up. If the AUX audio sounds distorted, turn the device’s volume down.

234 UNDERSTANDING YOUR INSTRUMENT PANEL

TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). Operating Instructions - Hands-Free Phone (UConnect威) (If Equipped) Refer to “Hands-Free Communication (UConnect威)” in Section 3. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to “Satellite Radio” in this section. Operating Instructions - Video Entertainment System™ (VES威) (If Equipped) Refer to separate “Video Entertainment System™ (VES威) Guide.”

SALES CODE REQ — AM/FM STEREO RADIO AND 6–DISC CD/DVD CHANGER (MP3/WMA AUX JACK)

NOTE: The radio sales code is located on the lower right side of your radio faceplate.

REQ Radio

Operating Instructions - Radio Mode

NOTE: The ignition switch must be in the ON or ACC position to operate the radio. Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360
degrees) in either direction without stopping. Turning the ON/VOLUME control knob to the right increases the volume and to the left decreases it. When the audio system is turned ON, the sound will be set at the same volume level as last played. SEEK Buttons Press and release the SEEK buttons to search for the next listenable station in AM/FM mode. Press the right switch

UNDERSTANDING YOUR INSTRUMENT PANEL 235

to seek up and the left switch to seek down. The radio will remain tuned to the new station until you make another selection. Holding either button will bypass stations without stopping until you release it. SCAN Button Pressing the SCAN button causes the tuner to search for the next listenable station, in AM, FM or Satellite (if equipped) frequencies, pausing for five seconds at each listenable station before continuing to the next. To stop the search, press the SCAN button a second time. Voice Recognition Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen.

236 UNDERSTANDING YOUR INSTRUMENT PANEL

Phone Button (UConnect威 Hands-Free Phone) — If Equipped Press this button to operate the Hands-Free Phone (UConnect威) feature (if equipped). Refer to “Hands-Free Communication (UConnect威)” in Section 3. If your vehicle is not equipped with or this feature is not available on your vehicle, a “Not Equipped With UConnect” message will display on the radio screen. TIME Button Press the TIME button and the time of day will display. In AM or FM mode, pressing the TIME button will switch between the time and frequency displays. Clock Setting Procedure 1. Press and hold the TIME button until the hours blink. 2. Adjust the hours by turning the right side TUNE/ SCROLL control knob.

3. After adjusting the hours, press the right side TUNE/ SCROLL control knob to set the minutes. The minutes will begin to blink. 4. Adjust the minutes using the right side TUNE/ SCROLL control knob. Press the TUNE/SCROLL control knob to save the time change. 5. To exit, press any button/knob or wait five seconds. The clock can also be set by pressing the SETUP button and selecting the “SET HOME CLOCK” entry. Once in this display follow the above procedure, starting at step 2. INFO Button Press the INFO button for an RDS station (one with call letters displayed). The radio will return a Radio Text message broadcast from an FM station (FM mode only).

RW/FF Pressing the RW (Rewind) or FF (Fast Forward) buttons causes the tuner to search for the next frequency in the direction of the arrows. This feature operates in AM, FM or Satellite (if equipped) frequencies. TUNE Control Turn the rotary TUNE/SCROLL control knob clockwise to increase or counterclockwise to decrease the frequency. Setting the Tone, Balance, and Fade Push the rotary TUNE/SCROLL control knob and BASS will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the bass tones. Push the rotary TUNE/SCROLL control knob a second time and MID will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the mid-range tones.

UNDERSTANDING YOUR INSTRUMENT PANEL 237

Push the rotary TUNE/SCROLL control knob a third time and TREBLE will display. Turn the TUNE/SCROLL control knob to the right or left to increase or decrease the treble tones. Push the rotary TUNE/SCROLL control knob a fourth time and BALANCE will display. Turn the TUNE/ SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers. Push the rotary TUNE/SCROLL control knob a fifth time and FADE will display. Turn the TUNE/SCROLL control knob to the left or right to adjust the sound level between the front and rear speakers. Push the rotary TUNE/SCROLL control knob again to exit setting tone, balance, and fade.

238 UNDERSTANDING YOUR INSTRUMENT PANEL

MUSIC TYPE Button Pressing this button once will turn on the Music Type mode for five seconds. Pressing the MUSIC TYPE button or turning the TUNE/SCROLL control knob within five seconds will allow the program format type to be se- lected. Many radio stations do not currently broadcast Music Type information. Toggle the MUSIC TYPE button to select the following format types:

Program Type

No program type or

undefined Adult Hits Classical

Classic Rock

College Country

16-Digit Character

Display

None

Adlt Hit Classicl Cls Rock College Country

Program Type

Foreign Language

Information

Jazz News

Nostalgia

Oldies

Personality

Public

Rhythm and Blues Religious Music Religious Talk

Rock Soft

Soft Rock

Soft Rhythm and Blues

16-Digit Character

Display Language

Inform Jazz News

Nostalga Oldies Persnlty Public R & B

Rel Musc Rel Talk

Rock Soft

Soft Rck Soft R&B

Program Type

Sports Talk Top 40
Weather

16-Digit Character Dis-

play Sports Talk Top 40
Weather

By pressing the SEEK button when the Music Type icon is displayed, the radio will be tuned to the next frequency station with the same selected Music Type name. The Music Type function only operates when in the FM mode. If a preset button is activated while in the Music Type (Program Type) mode, the Music Type mode will be exited and the radio will tune to the preset station. SETUP Button Pressing the SETUP button allows you to select between the following items:

UNDERSTANDING YOUR INSTRUMENT PANEL 239

NOTE: Turn the TUNE/SCROLL control knob to scroll through the entries. Push the AUDIO/SELECT button to select an entry and make changes. • DVD Enter - When the disc is in DVD Menu mode, selecting DVD Enter will allow you to play the current highlighted selection. Use the remote control to scroll up and down the menu (if equipped). • DISC Play/Pause - You can toggle between playing the DVD and pausing the DVD by pushing the SELECT button (if equipped). • DVD Play Options - Selecting the DVD Play Options will display the following: • Subtitle – Repeatedly pressing SELECT will switch subtitles to different subtitle languages that are available on the disc (if equipped).

240 UNDERSTANDING YOUR INSTRUMENT PANEL

• Audio Stream – Repeatedly pressing SELECT will switch to different audio languages (if supported on the disc) (if equipped). • Angle – Repeatedly pressing SELECT will change the viewing angle if supported by the DVD disc (if equipped).

NOTE: The available selections for each of the above entries varies depending upon the disc. NOTE: These selections can only be made while playing a DVD. • VES威 Power - Allows you to turn VES威 ON and OFF • VES威 Lock - Locks out rear VES威 remote controls (if

(if equipped).

equipped).

• VES威 CH1/CH2 - Allows the user to change the mode of either the IR1 or IR2, wireless headphones by pressing the AUDIO/SELECT button (if equipped). • Set Home Clock - Pressing the SELECT button allows you to set the clock. Turn the TUNE/SCROLL control knob to adjust the hours and then press and turn the TUNE/SCROLL control knob to adjust the minutes. Press the TUNE/SCROLL control knob again to save changes.