2011 Hyundai Elantra Owners Manual

responsibility of the driver to always check the speed and the distance to the vehicle ahead. Always hold the steering wheel firmly while driving.

(cid:129) Your vehicle is designed to acti- vate according to the driver’s intention, even with installed VSM. Always follow all the normal precautions for driving at safe speeds for the conditions – including driving inclement weather and on a slippery road.

(cid:129) Driving with varying tire or wheel sizes may cause the VSM system to malfunction. When replacing tires, make sure they are the same size as your original tires.

CRUISE CONTROL SYSTEM (IF EQUIPPED)

WARNING

(cid:129) If the cruise control is left on, (CRUISE indicator light in the instrument cluster illuminated) the cruise control can be activat- ed unintentionally. Keep the system off cruise (CRUISE light OFF) when the cruise control is not in use, to avoid inadvertently set- ting a speed.

control indicator

➀ CRUISE indicator ➁ SET indicator

OMD050032N

The cruise control system allows you to program the vehicle to maintain a con- stant speed without resting your foot on the accelerator pedal. This system is designed to function above approximately 25 mph (40 km/h).

(cid:129) Use the cruise control system only when traveling on open highways in good weather.

(cid:129) Do not use the cruise control when it may not be safe to keep the car at a constant speed, for instance, driving in heavy or varying traffic, or on slippery (rainy, icy or snow-covered) or winding roads or over 6% up-hill or down-hill roads.

(cid:129) Pay particular attention to the driving conditions whenever using the cruise control system. (cid:129) Be careful when driving downhill using the cruise control system, which may increase the vehicle speed.

Driving your vehicle

CAUTION

During cruise-speed driving of a manual transaxle vehicle, do not shift into neutral without depress- ing the clutch pedal, since the engine will be overrevved. If this happens, depress the clutch pedal or release the cruise control ON- OFF switch.

✽✽ NOTICE During normal cruise control operation, when the SET switch is activated or reactivated after applying the brakes, the cruise control will energize after approximately 3 seconds. This delay is normal.

5 31

Driving your vehicle

OMD050033N

To set cruise control speed: 1. Push the cruise ON-OFF button on the steering wheel to turn the system on. The CRUISE indicator light in the instrument cluster will illuminate.

2. Accelerate to the desired speed, which must be more than 25 mph (40 km/h).

OMD050036N 3. Push the SET- switch, and release it at the desired speed. The SET indicator light in the instrument cluster will illumi- nate. Release the accelerator at the same time. The desired speed will auto- matically be maintained.

On a steep grade, the vehicle may slow down or speed up slightly while going uphill or downhill.

OMD050035N

To increase cruise control set speed: Follow either of these procedures: (cid:129) Push the RES+ switch and hold it. Your vehicle will accelerate. Release the switch at the speed you want.

(cid:129) Push the RES+ switch and release it immediately. The cruising speed will increase 1.0 mph (1.6 km/h) each time the RES+ switch is operated in this manner.

32

To temporarily accelerate with the cruise control on: If you want to speed up temporarily when the cruise control is on, depress the accelerator pedal. Increased speed will not interfere with cruise control operation or change the set speed. To return to the set speed, take your foot off the accelerator.

OMD050036N

To decrease the cruising speed: Follow either of these procedures: (cid:129) Push the SET- switch and hold it. Your vehicle will gradually slow down. Release the switch at the speed you want to maintain.

(cid:129) Push the SET- switch and release it immediately. The cruising speed will decrease 1.0 mph (1.6 km/h) each time the SET- switch is operated in this manner.

Driving your vehicle

OMD050034N

To cancel cruise control, do one of the following: (cid:129) Press the brake pedal. (cid:129) Press the clutch pedal with a manual

transaxle.

(cid:129) Shift the shift lever into N (Neutral) with

an automatic transaxle

(cid:129) Press the CANCEL switch located on

the steering wheel.

(cid:129) Decrease the vehicle speed lower than the memory speed by 9 mph (15
km/h).

(cid:129) Decrease the vehicle speed to less than approximately 25 mph (40 km/h).

5 33

Driving your vehicle

Each of these actions will cancel cruise control operation (the SET indicator light in the instrument cluster will go off), but it will not turn the system off.If you wish to resume cruise control operation, push the RES+ switch located on your steering wheel.You will return to your previously preset speed.

34

OMD050033N To turn cruise control off, do one of the following: (cid:129) Push the cruise ON/OFF button (the CRUISE indicator light in the instru- ment cluster will go off).

(cid:129) Turn the ignition off. Both of these actions cancel cruise con- trol operation. If you want to resume cruise control operation, repeat the steps provided in “To set cruise control speed” on the previous page.

OMD050035N

To resume cruising speed at more than approximately 25 mph (40 km/h): If any method other than the cruise ON/OFF switch was used to cancel cruis- ing speed and the system is still activat- ed, the most recent set speed will auto- matically resume when the RES+ switch is pushed. It will not resume, however, if the vehicle speed has dropped below approximately 25 mph (40 km/h).

✽✽ NOTICE Always check the road conditions when pressing the RES+ switch to resume the speed.

(cid:129) Don't "ride" the brake pedal. This can increase fuel consumption and also increase wear on these components. In addition, driving with your foot rest- ing on the brake pedal may cause the brakes to overheat, which reduces their effectiveness and may lead to more serious consequences.

(cid:129) Take care of your tires. Keep them inflated to the recommended pressure. Incorrect inflation, either too much or too little, results in unnecessary tire wear. Check the tire pressures at least once a month.

(cid:129) Be sure that the wheels are aligned correctly. Improper alignment can result from hitting curbs or driving too fast over irregular surfaces. Poor align- ment causes faster tire wear and may also result in other problems as well as greater fuel consumption.

Driving your vehicle

(cid:129) Keep your car in good condition. For better fuel economy and reduced maintenance costs, maintain your car in accordance with the maintenance schedule in section 7. If you drive your car in severe conditions, more frequent maintenance is required (see section 7
for details).

(cid:129) Keep your car clean. For maximum serv- ice, your vehicle should be kept clean and free of corrosive materials. It is especially important that mud, dirt, ice, etc. not be allowed to accumulate on the underside of the car. This extra weight can result in increased fuel consumption and also contribute to corrosion.

(cid:129) Travel lightly. Don't carry unnecessary weight in your car. Weight reduces fuel economy.

(cid:129) Don't let the engine idle longer than necessary. If you are waiting (and not in traffic), turn off your engine and restart only when you're ready to go.

ECONOMICAL OPERATION Your vehicle's fuel economy depends mainly on your style of driving, where you drive and when you drive. Each of these factors affects how many miles (kilometers) you can get from a gal- lon (liter) of fuel. To operate your vehicle as economically as possible, use the fol- lowing driving suggestions to help save money in both fuel and repairs: (cid:129) Drive smoothly. Accelerate at a moder- ate rate. Don't make "jack-rabbit" starts or full-throttle shifts and maintain a steady cruising speed. Don't race between stoplights. Try to adjust your speed to that of the other traffic so you don't have to change speeds unneces- sarily. Avoid heavy traffic whenever possible. Always maintain a safe dis- tance from other vehicles so you can avoid unnecessary braking. This also reduces brake wear.

(cid:129) Drive at a moderate speed. The faster you drive, the more fuel your car uses. Driving at a moderate speed, especial- ly on the highway, is one of the most effective ways to reduce fuel consump- tion.

5 35

Driving your vehicle

(cid:129) Remember, your vehicle does not require extended warm-up. After the engine has started, allow the engine to run for 10 to 20 seconds prior to plac- ing the vehicle in gear. In very cold weather, however, give your engine a slightly longer warm-up period.

(cid:129) Don't "lug" or "over-rev" the engine. Lugging is driving too slowly in too high a gear resulting in the engine bucking. If this happens, shift to a lower gear. Over-revving is racing the engine beyond its safe limit. This can be avoid- ed by shifting at the recommended speeds.

(cid:129) Use your air conditioning sparingly. The air conditioning system is operat- ed by engine power so your fuel econ- omy is reduced when you use it.

(cid:129) Open windows at high speeds can

reduce fuel economy.

(cid:129) Fuel economy is less in crosswinds and headwinds. To help offset some of this loss, slow down when driving in these conditions.

Keeping a vehicle in good operating con- dition is important both for economy and safety. Therefore, have an authorized HYUNDAI dealer perform scheduled inspections and maintenance.

WARNING - Engine off dur-

ing motion

Never turn the engine off to coast down hills or anytime the vehicle is in motion. The power steering and power brakes will not function properly without the engine run- ning. Instead, keep the engine on and downshift to an appropriate gear for engine braking effect. In addition, turning off the ignition while driving could engage the steering wheel lock resulting in loss of vehicle steering which could cause serious injury or death.

36

SPECIAL DRIVING CONDITIONS

1JBB3302

Hazardous driving conditions When hazardous driving conditions are encountered such as water, snow, ice, mud, sand, or similar hazards, follow these suggestions: (cid:129) Drive cautiously and allow extra dis-

tance for braking.

(cid:129) Avoid sudden braking or steering.

WARNING - ABS

Do not pump the brake pedal on a vehicle equipped with ABS.

(cid:129) If stalled in snow, mud, or sand, use second gear. Accelerate slowly to avoid spinning the drive wheels.

(cid:129) Use sand, rock salt, tire chains, or other non-slip material under the drive wheels to provide traction when stalled in ice, snow, or mud.

WARNING - Downshifting

Downshifting with an automatic transaxle, while driving on slippery surfaces can cause an accident. The sudden change in tire speed could cause the tires to skid. Be careful when downshifting on slip- pery surfaces.

Driving your vehicle

Rocking the vehicle If it is necessary to rock the vehicle to free it from snow, sand, or mud, first turn the steering wheel right and left to clear the area around your front wheels. Then, shift back and forth between 1st (First) and R (Reverse) in vehicles equipped with a manual transaxle or R (Reverse) and any in vehicles equipped with an automatic transaxle. Do not race the engine, and spin the wheels as little as possible. If you are still stuck after a few tries, have the vehicle pulled out by a tow vehicle to avoid engine overheating and possible dam- age to the transaxle.

forward gear

CAUTION

Prolonged rocking may cause engine over-heating,transaxle dam- age or failure,and tire damage.

5 37

Driving your vehicle

WARNING - Spinning tires Do not spin the wheels, especially at speeds more than 35 mph (56
km/h). Spinning the wheels at high speeds when the vehicle is station- ary could cause a tire to overheat which could result in tire damage that may injure bystanders.

✽✽ NOTICE The ESC system should be turned OFF prior to rocking the vehicle.

WARNING

If your vehicle becomes stuck in snow, mud, sand, etc., then you may attempt to rock the vehicle free by moving it forward and backward. Do not attempt this procedure if people or objects are anywhere near the vehicle. During the rocking operation the vehicle may suddenly move forward or backward as it becomes unstuck, causing injury or damage to nearby people or objects.

38

OBH058035L

OMC035004

Smooth cornering Avoid braking or gear changing in cor- ners, especially when roads are wet. Ideally, corners should always be taken under gentle acceleration. If you follow these suggestions, tire wear will be held to a minimum.

Driving at night Because night driving presents more hazards than driving in the daylight, here are some important tips to remember: (cid:129) Slow down and keep more distance between you and other vehicles, as it may be more difficult to see at night, especially in areas where there may not be any street lights.

(cid:129) Adjust your mirrors to reduce the glare

from other driver's headlights.

(cid:129) Keep your headlights clean and prop- erly aimed on vehicles not equipped with the automatic headlight aiming feature. Dirty or improperly aimed headlights will make it much more diffi- cult to see at night.

(cid:129) Avoid staring directly at the headlights of oncoming vehicles. You could be temporarily blinded, and it will take several seconds for your eyes to read- just to the darkness.

Driving in the rain Rain and wet roads can make driving dangerous, especially if you’re not pre- pared for the slick pavement. Here are a few things to consider when driving in the rain: (cid:129) A heavy rainfall will make it harder to see and will increase the distance needed to stop your vehicle, so slow down.

(cid:129) Keep your windshield wiping equip- ment in good shape. Replace your windshield wiper blades when they show signs of streaking or missing areas on the windshield.

(cid:129) If your tires are not in good condition, making a quick stop on wet pavement can cause a skid and possibly lead to an accident. Be sure your tires are in good shape.

(cid:129) Turn on your headlights to make it eas-

ier for others to see you.

(cid:129) Driving too fast through large puddles can affect your brakes. If you must go through puddles, try to drive through them slowly.

(cid:129) If you believe you may have gotten your brakes wet, apply them lightly while driving until normal braking oper- ation returns.

Driving your vehicle

Driving in flooded areas Avoid driving through flooded areas unless you are sure the water is no high- er than the bottom of the wheel hub. Drive through any water slowly. Allow adequate stopping distance because brake performance may be affected. After driving through water, dry the brakes by gently applying them several times while the vehicle is moving slowly.

5 39

Fuel,engine coolant and engine oil High speed travel consumes more fuel than urban motoring. Do not forget to check both engine coolant and engine oil.

Drive belt A loose or damaged drive belt may result in overheating of the engine. Inspect your drive belt for proper tension, or have your Hyundai dealer inspect this at the normal service intervals listed in section 7.

WARNING

(cid:129) Underinflated or overinflated tires can cause poor handling, loss of vehicle control, and sud- den tire failure leading to acci- dents, injuries, and even death. Always check tires for proper inflation before driving. For prop- er tire pressures, refer to “Tires and wheels” in section 8.

(cid:129) Driving on tires with no or insuffi- cient tread is dangerous. Worn- out tires can result in loss of vehicle control, collisions, injury, and even death. Worn-out tires should be replaced as soon as possible and should never be used for driving. Always check the tire tread before driving your car. For further information and tread limits, refer to “Tires and wheels” in section 7.

Driving your vehicle

OMG015008

Highway driving Tires Adjust the tire inflation pressures to specification. Low tire inflation pressures will result in overheating and possible failure of the tires. Avoid using worn or damaged tires which may result in reduced traction or tire fail- ure.

✽✽ NOTICE Never exceed the maximum tire inflation pressure shown on the tires.

40

WINTER DRIVING

1JBB3305
More severe weather conditions of winter result in greater wear and other prob- lems. To minimize winter driving problem, you should follow these suggestions:

Snowy or icy conditions To drive your vehicle in deep snow, it may be necessary to use snow tires or to install tire chains on your tires. If snow tires are needed, it is necessary to select tires equivalent in size and type of the original equipment tires. Failure to do so may adversely affect the safety and han- dling of your car. Furthermore, speeding, rapid acceleration, sudden brake appli- cations, and sharp turns are potentially very hazardous practices. During deceleration, use engine braking to the fullest extent. Sudden brake appli- cations on snowy or icy roads may cause skids to occur. You need to keep suffi- cient distance between the vehicle in operation in front and your vehicle. Also, apply the brake gently. It should be noted that installing tire chains on the tire will provide a greater driving force, but will not prevent side skids.

✽✽ NOTICE Tire chains are not legal in all states. Check state laws before fitting tire chains.

Driving your vehicle

Snow tires If you mount snow tires on your vehicle, make sure they are radial tires of the same size and load range as the original tires. Mount snow tires on all four wheels to balance your vehicle’s handling in all weather conditions. Keep in mind that the traction provided by snow tires on dry roads may not be as high as your vehi- cle's original equipment tires. You should drive cautiously even when the roads are clear. Check with the tire dealer for max- imum speed recommendations.

WARNING - Snow tire size Snow tires should be equivalent in size and type to the vehicle's stan- dard tires. Otherwise, the safety and handling of your vehicle may be adversely affected.

Do not install studded tires without first checking local, state and municipal regu- lations for possible restrictions against their use.

5 41

CAUTION

(cid:129) Make sure the snow chains are the correct size and type for your tires. Incorrect snow chains can cause damage to the vehicle body and suspension and may not be covered by your vehicle manufac- turer warranty. Also, the snow chain connecting hooks may be damaged from contacting vehicle components causing the snow chains to come loose from the tire. Make sure the snow chains are SAE class “S”certified.

(cid:129) Always check chain installation for proper mounting after driving approximately 0.3 to 0.6 miles (0.5
to 1 km) to ensure safe mounting. Retighten or remount the chains if they are loose.

Chain installation When installing chains, follow the manu- facturer's instructions and mount them as tightly as you can. Drive slowly with chains installed. If you hear the chains contacting the body or chassis, stop and tighten them. If they still make contact, slow down until it stops. Remove the chains as soon as you begin driving on cleared roads.

WARNING - Mounting chains

When mounting snow chains, park the vehicle on level ground away from traffic. Turn on the vehicle Hazard Warning flashers and place a triangular emergency warning device behind the vehicle if avail- able. Always place the vehicle in P (Park), apply the parking brake and turn off the engine before installing snow chains.

Driving your vehicle

1JBA4068

Tire chains Since the sidewalls of radial tires are thinner, they can be damaged by mount- ing some types of snow chains on them. Therefore, the use of snow tires is rec- ommended instead of snow chains. Do not mount tire chains on vehicles equipped with aluminum wheels; snow chains may cause damage to the wheels. If snow chains must be used, use gen- uine HYUNDAI parts and install the tire chain after going over the instruction. Damage to your vehicle caused by improper snow chain use is not covered by your vehicle manufacturers warranty. When using tire chains, install them on the front tires only.

42

Driving your vehicle

Change to "winter weight" oil if necessary In some climates it is recommended that a lower viscosity "winter weight" oil be used during cold weather. See section 8
for recommendations. If you aren't sure what weight oil you should use, consult an authorized HYUNDAI dealer.

Check spark plugs and ignition system Inspect your spark plugs as described in section 7 and replace them if necessary. Also check all ignition wiring and compo- nents to be sure they are not cracked, worn or damaged in any way.

WARNING - Tire chains

(cid:129) The use of chains may adversely

affect vehicle handling.

(cid:129) Do not exceed 20 mph (30 km/h) or the chain manufacturer’s rec- ommended speed limit, whichev- er is lower.

(cid:129) Drive carefully and avoid bumps, holes, sharp turns, and other road hazards, which may cause the vehicle to bounce.

(cid:129) Avoid sharp turns or locked-

wheel braking.

CAUTION

(cid:129) Chains that are the wrong size or improperly installed can damage your vehicle's brake lines, sus- pension,body and wheels.

(cid:129) Stop driving and retighten the chains any time you hear them hitting the vehicle.

Use high quality ethylene glycol coolant Your vehicle is delivered with high quality ethylene glycol coolant in the cooling system. It is the only type of coolant that should be used because it helps prevent corrosion in the cooling system, lubri- cates the water pump and prevents freezing. Be sure to replace or replenish your coolant in accordance with the maintenance schedule in section 7. Before winter, have your coolant tested to assure that its freezing point is sufficient for the temperatures anticipated during the winter.

Check battery and cables Winter puts additional burdens on the battery system. Visually inspect the bat- tery and cables as described in section 7. The level of charge in your battery can be checked by an authorized HYUNDAI dealer or a service station.

5 43

Carry emergency equipment Depending on the severity of the weath- er where you drive your car, you should carry appropriate emergency equipment. Some of the items you may want to carry include tire chains, tow straps or chains, flashlight, emergency flares, sand, a shovel, jumper cables, a window scraper, gloves, ground cloth, coveralls, a blanket, etc.

Driving your vehicle

To keep locks from freezing To keep the locks from freezing, squirt an approved de-icer fluid or glycerine into the key opening. If a lock is covered with ice, squirt it with an approved de-icing fluid to remove the ice. If the lock is frozen internally, you may be able to thaw it out by using a heated key. Handle the heated key with care to avoid injury.

Use approved window washer anti-freeze in system To keep the water in the window washer system from freezing, add an approved window washer anti-freeze solution in accordance with instructions on the con- tainer. Window washer anti-freeze is available from an authorized HYUNDAI dealer and most auto parts outlets. Do not use engine coolant or other types of anti-freeze as these may damage the paint finish.

Don't let your parking brake freeze Under some conditions your parking brake can freeze in the engaged position. This is most likely to happen when there is an accumulation of snow or ice around or near the rear brakes or if the brakes are wet. If there is a risk of the parking brake may freezing, apply it only tem- porarily while you put the shift lever in P (automatic transaxle) or in first or reverse gear (manual transaxle) and block the rear wheels so the vehicle cannot roll. Then release the parking brake.

Don't let ice and snow accumu- late underneath Under some conditions, snow and ice can build up under the fenders and inter- fere with the steering. When driving in severe winter conditions where this may happen, you should periodically check underneath the car to be sure the move- ment of the front wheels and the steering components is not obstructed.

44

VEHICLE LOAD LIMIT

Type A

Type D

Type B

Type E

Type C

Type F

Driving your vehicle

Tire and loading information label The label located on the driver's door sill gives the original tire size, cold tire pressures recommended for your vehicle, the number of people that can be in your vehicle and vehicle capacity weight.

Vehicle capacity weight:

849 lbs. (385 kg)

Vehicle capacity weight is the maxi- mum combined weight of occupants and cargo.

OMD050040N/OMD050041N/OMD050042N/OMD050043N/OMD050044N/OMD050045N

5 45

Steps For Determining Correct Load Limit - 1. Locate the statement "The com- bined weight of occupants and cargo should never exceed XXX kg or XXX lbs.'' on your vehicle's placard.

2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.

3. Subtract the combined weight of the driver and passengers from XXX kg or XXX lbs.

4. The resulting figure equals the available amount of cargo and lug- gage load capacity. For example, if the "XXX" amount equals 1400
lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and lug- gage load capacity is 650 lbs. (1400-750 (5 x 150) = 650 lbs.)

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

6. If your vehicle will be towing a trail- er, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

✽✽ NOTICE We do not recommend using this vehicle for trailer towing.

Driving your vehicle

Seating capacity:

Total : 5 persons

(Front seat : 2 persons, Rear seat : 3 persons)

Seating capacity is the maximum number of occupants including a driver, your vehicle may carry. However, the seating capacity may be reduced based upon the weight of all of the occupants, and the weight of the cargo being carried. Do not overload the vehicle as there is a limit to the total weight, or load limit including occupants and cargo, the vehicle can carry.

Towing capacity: We do not recommend using this vehicle for trailer towing.

Cargo capacity: The cargo capacity of your vehicle will increase or decrease depending on the weight and the number of occupants.

46

Example 1

Example 2

Example 3

Driving your vehicle

Item

Description

Vehicle Capacity

Weight

Subtract Occupant

Weight

C190F01JM

Total 849 lbs (385 kg)

300 lbs (136 kg)

150 lbs (68 kg) × 2
Available Cargo and 549 lbs (249 kg)

Luggage weight

Item

Description

Vehicle Capacity

Weight

Subtract Occupant

Weight

150 lbs (68 kg) × 5
Available Cargo and

Luggage weight

C190F02JM

Total 849 lbs (385 kg)

750 lbs (340 kg)

99 lbs (45 kg)

Item

Description

Vehicle Capacity

Weight

Subtract Occupant

Weight

163 lbs (74 kg) × 5
Available Cargo and

Luggage weight

C190F03JM

Total 849 lbs (385 kg)

815 lbs (370 kg)

34 lbs (15 kg)

Refer to your vehicle’s tire and loading information label for specific information about your vehicle's capacity weight and seating positions. The combined weight of the driver, passengers and cargo should never exceed your vehicle's capacity weight.

5 47

Driving your vehicle

OBH059070

Certification label The certification label is located on the driver's door sill at the center pillar. This label shows the maximum allowable weight of the fully loaded vehicle. This is called the GVWR (Gross Vehicle Weight Rating). The GVWR includes the weight of the vehicle, all occupants, fuel and cargo. This label also tells you the maxi- mum weight that can be supported by the front and rear axles, called Gross Axle Weight Rating (GAWR).

48

To find out the actual loads on your front and rear axles, you need to go to a weigh station and weigh your vehicle.Your dealer can help you with this. Be sure to spread out your load equally on both sides of the center- line.

WARNING - Over loading

(cid:129) Never exceed the GVWR for your vehicle, the GAWR for either the front or rear axle and vehicle capacity weight. Exceeding these ratings can cause an accident or vehicle damage.You can calculate the weight of your load by weigh- ing the items (or people) before putting them in the vehicle. Be careful not to over- load your vehicle.

(Continued)

(Continued) (cid:129) Do not load your vehicle any heavier than the GVWR, either the maximum front or rear GAWR and vehicle capacity weight. If you do, parts, including tires on your vehicle can break, and it can change the way your vehicle handles and braking ability. This could cause you to lose control and crash. Also, overloading can shorten the life of your vehi- cle.

The label will help you decide how much cargo and installed equipment your vehicle can carry.

If you carry items inside your vehicle - like suitcases, tools, packages, or anything else - they are moving as fast as the vehicle. If you have to stop or turn quickly, or if there is a crash, the items will keep going and can cause an injury if they strike the driv- er or a passenger.

WARNING

(cid:129) Overloading your vehicle can cause heat buildup in your vehicle's tires and possible tire failure that could lead to a crash.

(cid:129) Overloading your vehicle can cause increased stopping dis- tances that could lead to a crash.

(cid:129) A crash resulting from poor handling, vehicle damage, tire failure, or increased stopping distances could result in seri- ous injury or death.

CAUTION

(cid:129) Overloading your vehicle may cause damage. Repairs would not be covered by your warran- ty.Do not overload your vehicle. (cid:129) Using heavier suspension com- ponents to get added durability might not change your weight ratings.Ask your dealer to help you load your vehicle the right way.

Driving your vehicle

WARNING - Loose cargo

Items you carry inside your vehicle can strike and injure occupants in a sudden stop or turn, or in a crash. (cid:129) Put items in the cargo area of your vehicle. Try to spread the weight evenly.

(cid:129) Never stack items, like suit- the vehicle

cases, above the tops of the seats.

inside

(cid:129) Do not leave an unsecured child restraint in your vehicle. (cid:129) When you carry something

inside the vehicle, secure it.

(cid:129) Do not drive with a seat folded

down unless necessary.

5 49

Driving your vehicle

VEHICLE WEIGHT This section will guide you in the proper loading of your vehicle, to keep your loaded vehicle weight within its design rating capability. Properly loading your vehicle will provide maximum return of the vehicle design performance. Before loading your vehicle, familiarize yourself with the following terms for determining your vehicle's weight ratings, from the vehicle's specifications and the certifica- tion label:

Base curb weight This is the weight of the vehicle including a full tank of fuel and all standard equip- ment. It does not include passengers, cargo, or optional equipment.

Vehicle curb weight This is the weight of your new vehicle when you picked it up from your dealer plus any aftermarket equipment.

Cargo weight This figure includes all weight added to the Base Curb Weight, including cargo and optional equipment.

GAW (Gross axle weight) This is the total weight placed on each axle (front and rear) - including vehicle curb weight and all payload.

GAWR (Gross axle weight rating) This is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the certification label. The total load on each axle must never exceed its GAWR.

GVW (Gross vehicle weight) This is the Base Curb Weight plus actual Cargo Weight plus passengers.

GVWR (Gross vehicle weight rating) This is the maximum allowable weight of the fully loaded vehicle (including all options, equipment, passengers and cargo). The GVWR is shown on the cer- tification label located on the driver’s door sill.

50

TRAILER TOWING We do not recommend using this vehicle for trailer towing.

Driving your vehicle

5 51

Road warning / 6-2
In case of an emergency while driving / 6-2
If the engine will not start / 6-3
Emergency starting / 6-4
If the engine overheats / 6-6
Tire pressure monitoring system (TPMS) / 6-7
If you have a flat tire (with spare tire) / 6-12
If you have a flat tire (with tire mobility kit) / 6-20
Towing / 6-26

What to do in an emergency

What to do in an emergency

ROAD WARNING

OMD060001N

Hazard warning flasher The hazard warning flasher serves as a warning to other drivers to exercise extreme caution when approaching, overtaking, or passing your vehicle.

It should be used whenever emergency repairs are being made or when the vehi- cle is stopped near the edge of a road- way. Depress the flasher switch with the igni- tion switch in any position. The flasher switch is located in the center console switch panel. All turn signal lights will flash simultaneously.

• The hazard warning flasher operates whether your vehicle is running or not. (cid:129) The turn signals do not work when the

hazard flasher is on.

(cid:129) Care must be taken when using the hazard warning flasher while the vehi- cle is being towed.

IN CASE OF AN EMERGENCY WHILE DRIVING If the engine stalls at a crossroad or crossing If the engine stalls at a crossroad or crossing, set the shift lever in the N (Neutral) position and then push the vehi- cle to a safe place.

If you have a flat tire while driving If a tire goes flat while you are driving: 1.Take your foot off the accelerator pedal and let the car slow down while driving straight ahead. Do not apply the brakes immediately or attempt to pull off the road as this may cause a loss of con- trol. When the car has slowed to such a speed that it is safe to do so, brake carefully and pull off the road. Drive off the road as far as possible and park on firm, level ground. If you are on a divid- ed highway, do not park in the median area between the two traffic lanes.

26

What to do in an emergency

If engine turns over normally but does not start 1. Check fuel level. 2. With the ignition switch in the LOCK position, check all connectors at igni- tion coils and spark plugs. Reconnect any that may be disconnected or loose.

3. If the engine still does not start, call an authorized HYUNDAI dealer or seek other qualified assistance.

2.When the vehicle is stopped, turn on your emergency hazard flashers, set the parking brake and put the transaxle in P (automatic transaxle) or reverse (manual transaxle).

3.Have all passengers get out of the car. Be sure they all get out on the side of the car that is away from traffic.

4.When repairing a flat tire, follow the instruction provided later in this sec- tion.

If engine stalls while driving 1. Reduce your speed gradually, keeping a straight line. Move cautiously off the road to a safe place.

2. Turn on your emergency flashers. 3. Try to start the engine again. If your vehicle will not start, contact an authorized HYUNDAI dealer or seek other qualified assistance.

IF THE ENGINE WILL NOT START If engine doesn't turn over or turns over slowly 1. If your vehicle has an automatic transaxle, be sure the shift lever is in N (Neutral) or P (Park) and the emer- gency brake is set.

2. Check the battery connections to be

sure they are clean and tight.

3. Turn on the interior light. If the light dims or goes out when you operate the starter, the battery is discharged.

4. Do not push or pull the vehicle to start it. See instructions for "Jump starting".

WARNING

If the engine will not start, do not push or pull the vehicle to start it. This could result in a collision or cause other damage. In addition, push or pull starting may cause the catalytic converter to be over- loaded and create a fire hazard.

6 3

What to do in an emergency

EMERGENCY STARTING

Jumper Cables

Booster battery

Jumper terminal

1VQA4001
Connect cables in numerical order and disconnect in reverse order.

46

Jump starting Jump starting can be dangerous if done incorrectly. Therefore, to avoid harm to yourself or damage to your vehicle or battery, follow the jump starting proce- dures. If in doubt, we strongly recom- mend that you have a competent techni- cian or towing service jump start your vehicle.

CAUTION

Use only a 12-volt jumper system. You can damage a 12-volt starting motor, ignition system, and other electrical parts beyond repair by use of a 24-volt power supply (either two 12-volt batteries in series or a 24-volt motor generator set).

WARNING - Battery

Never attempt to check the elec- trolyte level of the battery as this may cause the battery to rupture or explode causing serious injury.

WARNING - Battery

• Keep all flames or sparks away from the battery. The battery pro- duces hydrogen gas which may explode if exposed to flame or sparks. If these instructions are not fol- lowed exactly, serious personal injury and damage to the vehicle may occur! If you are not sure how to follow this procedure, seek assistance. Automobile batteries contain sul- furic acid. This is poisonous and highly corrosive. When jump starting, wear protective glasses and be careful not to get acid on yourself, your clothing or on the car.

qualified

(cid:129) Do not attempt to jump start the vehicle if the discharged battery is frozen or if the electrolyte level is low; the battery may rupture or explode.

What to do in an emergency

Push-starting Your manual transaxle-equipped vehicle should not be push-started because it might damage the emission control sys- tem. Vehicles equipped with automatic transaxle cannot be push-started. Follow the directions in this section for jump-starting.

WARNING

Never tow a vehicle to start it because the sudden surge forward when the engine starts could cause a collision with the tow vehicle.

Jump starting procedure 1. Make sure the booster battery is 12- volt and that its negative terminal is grounded.

2. If the booster battery is in another vehicle, do not allow the vehicles to touch.

3. Turn off all unnecessary electrical

loads.

4. Connect the jumper cables in the exact sequence shown in the illustration. First connect one end of a jumper cable to the positive terminal of the discharged battery (1), then connect the other end to the positive terminal on the booster battery (2). Proceed to connect one end of the other jumper cable to the negative terminal of the booster battery (3), then the other end to a solid, stationary, metallic point (for example, the engine lifting bracket) away from the battery (4). Do not con- nect it to or near any part that moves when the engine is cranked.

Do not allow the jumper cables to con- tact anything except the correct battery terminals or the correct ground. Do not lean over the battery when making connections.

CAUTION - Battery cables

Do not connect the jumper cable from the negative terminal of the booster battery to the negative ter- minal of the discharged battery. This can cause the discharged bat- tery to overheat and crack, releas- ing battery acid.

5. Start the engine of the vehicle with the booster battery and let it run at 2,000
rpm, then start the engine of the vehi- cle with the discharged battery.

If the cause of your battery discharging is not apparent, you should have your vehi- cle checked by an authorized HYUNDAI dealer.

6 5

What to do in an emergency

IF THE ENGINE OVERHEATS If your temperature gauge indicates over- heating, you experience a loss of power, or hear loud pinging or knocking, the engine is probably too hot. If this hap- pens, you should:

1. Pull off the road and stop as soon as it

is safe to do so.

2. Place the shift lever in P (automatic transaxle) or neutral (manual transaxle) and set the parking brake. If the air con- ditioning is on, turn it off.

3. If engine coolant is running out under the car or steam is coming out from the hood, stop the engine. Do not open the hood until the coolant has stopped running or the steaming has stopped. If there is no visible loss of engine coolant and no steam, leave the engine running and check to be sure the engine cooling fan is operating. If the fan is not running, turn the engine off.

66

6.If you cannot find the cause of the overheating, wait until the engine tem- perature has returned to normal. Then, if coolant has been lost, carefully add coolant to the reservoir to bring the fluid level in the reservoir up to the halfway mark.

7.Proceed with caution, keeping alert for further signs of overheating. If over- heating happens again, call an author- ized HYUNDAI dealer for assistance.

CAUTION

Serious loss of coolant indicates there is a leak in the cooling system and this should be checked as soon as possible by an authorized HYUNDAI dealer.

4. Check to see if the water pump drive belt is missing. If it is not missing, check to see that it is tight. If the drive belt seems to be satisfactory, check for coolant leaking from the radiator, hoses or under the car. (If the air con- ditioning had been in use, it is normal for cold water to be draining from it when you stop.)

WARNING

While the engine is running, keep hair, hands and clothing away from moving parts such as the fan and drive belts to prevent injury.

5. If the water pump drive belt is broken or engine coolant is leaking out, stop the engine immediately and call the nearest authorized HYUNDAI dealer for assistance.

WARNING

Do not remove the radiator cap when the engine is hot. This may result in coolant being blown out of the opening and cause serious burns.

TIRE PRESSURE MONITORING SYSTEM (TPMS, IF EQUIPPED)

As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pres- sure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a signifi- cantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability.

Please note that the TPMS is not a substitute for proper tire mainte- nance, and it is the driver’s responsi- bility to maintain correct tire pres- sure, even if under-inflation has not reached the level to trigger illumina- tion of the TPMS low tire pressure telltale.

OMD060002

(1) Low tire pressure telltale / TPMS malfunction indicator

Each tire, including the spare (if pro- vided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehi- cle manufacturer on the vehicle plac- ard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pres- sure label, you should determine the proper tire inflation pressure for those tires.)

What to do in an emergency

Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS mal- function indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximate- ly one minute and then remain con- tinuously illuminated. This sequence will continue upon subsequent vehi- cle start-ups as long as the malfunc- tion exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alter- nate tires and wheels allow the TPMS to continue to function proper- ly.

6 7

What to do in an emergency

✽✽ NOTICE If the TPMS indicator does not illu- minate for 3 seconds when the igni- tion switch is turned to the ON posi- tion or engine is running, or if it comes on after blinking for approxi- mately one minute, take your car to your nearest authorized HYUNDAI dealer and have the system checked.

86

CAUTION

In winter or cold weather, the low tire pressure telltale may be illuminated if the tire pressure was adjusted to the recom- mended tire inflation pressure in warm weather. It does not mean your TPMS is malfunction- ing because the decreased tem- perature leads to a proportional lowering of tire pressure. When you drive your vehicle from a warm area to a cold area or from a cold area to a warm area,or the outside temperature is greatly higher or lower, you should check the tire inflation pressure and adjust the tires to the recommended tire inflation pressure.

Low tire pressure tell- tale

When the tire pressure monitoring system warning indicator is illuminat- ed, one or more of your tires is sig- nificantly under-inflated. If the telltale illuminates, immediately reduce your speed, avoid hard cor- nering and anticipate increased stop- ping distances. You should stop and check your tires as soon as possible. Inflate the tires to the proper pres- sure as indicated on the vehicle’s placard or tire inflation pressure label located on the driver’s side center pil- lar outer panel. If you cannot reach a service station or if the tire cannot hold the newly added air, replace the low pressure tire with the spare tire. Then the Low Tire Pressure telltale may flash for approximately one minute and then remain continuously illuminated after restarting and about 20 minutes of continuous driving before you have the low pressure tire repaired and replaced on the vehicle.

WARNING - Low pressure

damage

Significantly low tire pressure makes the vehicle unstable and can contribute to loss of vehicle control and increased braking distances. Continued driving on low pres- sure tires can cause the tires to overheat and fail.

TPMS (Tire Pressure Monitoring System) malfunction indicator

The TPMS malfunction indicator will illuminate after it blinks for approxi- mately one minute when there is a problem with the Tire Pressure Monitoring System. If the system is able to correctly detect an under infla- tion warning at the same time as sys- tem failure then it will illuminate the TPMS malfunction indicator. Have the system checked by an authorized HYUNDAI dealer as soon as possible to determine the cause of the problem.

What to do in an emergency

CAUTION

(cid:129) The TPMS malfunction indica- tor may be illuminated if the vehicle is moving around elec- tric power supply cables or radios transmitter such as at police stations, government and public offices,broadcast- ing stations, military installa- tions,airports,or transmitting towers,etc.This can interfere with normal operation of the Tire Pressure Monitoring System (TPMS).

(cid:129) The TPMS malfunction indica- tor may illuminate if snow chains or some separately purchased devices such as notebook computers, mobile charger, remote starter, navi- gation etc. are used in the vehicle.This can interfere with normal operation of the Tire Pressure Monitoring System (TPMS).

6 9

CAUTION

If original mounted tire is replaced with the spare tire,the TPMS sensor on the replaced spare wheel should be initiated and the TPMS sensor on the original mounted wheel should be deactivated by a HYUNDAI dealer.If the TPMS sensor on the original mounted wheel located in the spare tire carrier still acti- vates,the tire pressure monitor- ing system may not operate properly.Have the tire with TPMS serviced or replaced by an authorized HYUNDAIdealer.

What to do in an emergency

Changing a tire with TPMS If you have a flat tire, the Low Tire Pressure will come on. Have the flat tire repaired by an authorized HYUNDAI dealer as soon as possi- ble or replace the flat tire with the spare tire.

CAUTION

Never use a puncture-repairing agent not approved by HYUNDAI to repair and/or inflate a low pressure tire.The tire sealant not approved by HYUNDAI may dam- age the tire pressure sensor. The sealant on the tire pressure sensor and wheel shall be elem- inated when you replace the tire with a new one.

10

Each wheel is equipped with a tire pressure sensor mounted inside the tire behind the valve stem. You must use TPMS specific wheels. It is rec- ommended that you always have your tires serviced by an authorized HYUNDAI dealer. Even if you replace the low pressure tire with the spare tire, the Low Tire Pressure Telltale will blink or remain on until the low pressure tire is repaired and placed on the vehicle. After you replace the low pressure tire with the spare tire, the Low Tire Pressure Telltale may blink or illumi- nate after a few minutes because the TPMS sensor mounted on the spare wheel is not initiated. Once the low pressure tire is reinflat- ed to the recommended pressure and installed on the vehicle or the TPMS sensor mounted on the replaced spare wheel is initiated by an authorized HYUNDAI dealer, the TPMS malfunction indicator and the low tire pressure telltale will extin- guish within a few minutes of driving. If the indicator is not extinguished after a few minutes of driving, please visit an authorized HYUNDAI dealer.

You may not be able to identify a low tire by simply looking at it. Always use a good quality tire pressure gauge to measure the tire's inflation pressure. Please note that a tire that is hot (from being driven) will have a higher pressure measurement than a tire that is cold. A cold tire means the vehicle has been sitting for 3 hours and driven for less than 1 mile (1.6 km) in that 3
hour period. Allow the tire to cool before measur- ing the inflation pressure. Always be sure the tire is cold before inflating to the recommended pressure.

CAUTION

Do not use any tire sealant except the Tire Mobility Kit approved by HYUNDAI if your vehicle is equipped with a Tire Pressure Monitoring System. The liquid sealant can damage the tire pressure sensors.

WARNING - TPMS

(cid:129) The TPMS cannot alert you to severe and sudden tire dam- age caused by external fac- tors such as nails or road debris.

(cid:129) If you feel any vehicle instabil- ity, immediately take your foot off the accelerator, apply the brakes gradually and with light force, and slowly move to a safe position off the road.

WARNING - Protecting

TPMS

Tampering with, modifying, or disabling the Tire Pressure Monitoring System (TPMS) com- ponents may interfere with the system's ability to warn the driv- er of low tire pressure condi- tions and/or TPMS malfunctions. Tampering with, modifying, or disabling the Tire Pressure Monitoring System (TPMS) com- ponents may void the warranty for that portion of the vehicle.

What to do in an emergency

This device complies with Part 15
of the FCC rules. Operation is subject to the following two conditions: 1.This device may not cause harmful

interference, and

2.This device must accept any inter- ference received, including inter- ference that may cause undesired operation.

WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

6 11

What to do in an emergency

IF YOU HAVE A FLAT TIRE (WITH SPARE TIRE, IF EQUIPPED)

Jacking instructions The jack is provided for emergency tire changing only. To prevent the jack from “rattling” while the vehicle is in motion, store it properly. Follow jacking instructions to reduce the possibility of personal injury.

OMD060003

Jack and tools The jack, jack handle, and wheel lug nut wrench are stored in the luggage compartment. Pull up the luggage box cover to reach this equipment. (1) Jack handle (2) Jack (3) Wheel lug nut wrench

12

WARNING - Changing tires (cid:129) Never attempt vehicle repairs in the traffic lanes of a public road or highway.

(cid:129) Always move the vehicle com- pletely off the road and onto the shoulder before trying to change a tire. The jack should be used on level firm ground. If you cannot find a firm, level place off the road, call a tow- ing service company for assistance.

(cid:129) Be sure to use the correct front and rear jacking posi- tions on the vehicle; never use the bumpers or any other part of the vehicle for jack support. (cid:129) The vehicle can easily roll off the jack causing serious injury or death. No person should place any portion of their body under a vehicle that is supported only by a jack; use vehicle support stands.

(Continued)

(Continued) (cid:129) Do not start or run the engine while the vehicle is on the jack.

(cid:129) Do not allow anyone to remain in the vehicle while it is on the jack.

(cid:129) Make sure any children pres- ent are in a secure place away from the road and from the vehicle to be raised with the jack.

What to do in an emergency

OYF069005N

OBH068002L

Removing and storing the spare tire Turn the tire hold-down wing bolt counterclockwise. Store the tire in the reverse order of removal. To prevent the spare tire and tools from “rattling” while the vehicle is in motion, store them properly.

Changing tires 1. Park on a level surface and apply

2. Shift

the shift

the parking brake firmly. lever

into R (Reverse) with manual transaxle or P (Park) with automatic transaxle.

3. Activate the hazard warning flash-

er.

6 13

WARNING - Changing a tire (cid:129) To prevent vehicle movement while changing a tire, always set the parking brake fully, and always block the wheel diagonally opposite the wheel being changed.

(cid:129) We

that

recommend

the wheels of the vehicle be blocked, and that no person remain in a vehicle that is being jacked.

OMD060006
6. Insert the screwdriver into the groove of the wheel cap and pry gently to remove the wheel cap (If equipped).

What to do in an emergency

1JBA6504
4. Remove the wheel lug nut wrench, jack, jack handle, and spare tire from the vehicle.

5. Block both the front and rear of the wheel that is diagonally opposite the jack position.

14

What to do in an emergency

OMD060009
7. Loosen the wheel lug nuts coun- terclockwise one turn each, but do not remove any nut until the tire has been raised off the ground.

OYF069019N 8. Place the jack at the front or rear jacking position closest to the tire you are changing. Place the jack at the designated locations under the frame.

WARNING - Jack location

To reduce the possibility of injury, be sure to use only the jack provided with the vehicle and in the correct jack position; never use any other part of the vehicle for jack support.

OMD060008
9. Insert the jack handle into the jack and turn it clockwise, raising the vehicle until the tire just clears the ground. This measurement is approximately 1.2 in (30 mm). Before removing the wheel lug nuts, make sure the vehicle is sta- ble and that there is no chance for movement or slippage.

6 15

11. To reinstall the wheel, hold it on the studs, put the wheel nuts on the studs and tighten them finger tight. The nuts should be installed with their tapered small diameter ends directed inward. Jiggle the tire to be sure it is completely seated, then tighten the nuts as much as possible with your fin- gers again.

12. Lower the car to the ground by turning the wheel nut wrench counterclockwise.

WARNING

from

Wheels may have sharp edges. Handle them carefully to avoid possible severe injury. Before putting the wheel into place, be sure that there is nothing on the hub or wheel (such as mud, tar, gravel, etc.) that prevents the wheel fitting solidly against the hub. If there is, remove it. If there is not good contact on the mount- ing surface between the wheel and hub, the wheel nuts could come loose and cause the loss of a wheel. Loss of a wheel may result in loss of control of the vehicle. This may cause serious injury or death.

What to do in an emergency

10. Loosen

the wheel nuts and remove them with your fingers. Slide the wheel off the studs and lay it flat so it cannot roll away. To put the wheel on the hub, pick up the spare tire, line up the holes with the studs and slide the wheel onto them. If this is difficult, tip the wheel slightly and get the top hole in the wheel lined up with the top stud. Then jiggle the wheel back and forth until the wheel can be slid over the other studs.

16

If you have a tire gauge, remove the valve cap and check the air pressure. If the pressure is lower than recom- mended, drive slowly to the nearest service station and inflate to the cor- rect pressure. If it is too high, adjust it until it is correct. Always reinstall the valve cap after checking or adjusting tire pressure. If the cap is not replaced, air may leak from the tire. If you lose a valve cap, buy another and install it as soon as possible. After you have changed wheels, always secure the flat tire in its place and return the jack and tools to their proper storage locations.

What to do in an emergency

CAUTION

Your vehicle has metric threads on the wheel studs and nuts. Make certain during wheel removal that the same nuts that were removed are reinstalled - or, if replaced, that nuts with metric threads and the same chamfer configuration are used. Installation of a non-metric thread nut on a metric stud or vice-versa will not secure the wheel to the hub properly and will damage the stud so that it must be replaced. Note that most lug nuts do not have metric threads.Be sure to use extreme care in checking for thread style before installing aftermarket lug nuts or wheels. If in doubt, consult an author- ized HYUNDAI dealer.

6 17

OUN046019
Then position the wrench as shown in the drawing and tighten the wheel nuts. Be sure the socket is seated completely over the nut. Do not stand on the wrench handle or use an extension pipe over the wrench han- dle. Go around the wheel tightening every other nut until they are all tight. Then double-check each nut for tightness. After changing wheels, have an authorized HYUNDAI dealer tighten the wheel nuts to their proper torque as soon as possible.

Wheel nut tightening torque: Steel wheel & aluminum alloy wheel: 65~79 lb·ft (9~11 kg·m)

What to do in an emergency

WARNING - Wheel studs

If the studs are damaged, they may lose their ability to retain the wheel. This could lead to the loss of the wheel and a collision resulting in serious injuries.

To prevent the jack, jack handle, wheel lug nut wrench and spare tire from rattling while the vehicle is in motion, store them properly.

WARNING - Inadequate spare tire pressure

Check the inflation pressures as soon as possible after installing the spare tire. Adjust it to the specified pressure, if necessary. Refer to “Tires and wheels” sec- tion 8.

Important - use of compact spare tire (if equipped) If your vehicle is equipped with a compact spare tire, it will take up less space than a regular-size tire. This tire is smaller than a conventional tire and is designed for temporary use only.