’’
Turning the dial to the ‘‘ position turns on the headlights. If you leave the lights on and remove the key from the ignition switch, you will hear a reminder chime when you open the driver’s door.
’’ or
’’ position, the lights on
When the dial is in the ‘‘ ‘‘ indicator comes on as a reminder. This indicator stays on if you leave the lights on and turn the ignition switch to ACCESSORY (I) or LOCK (0).
74
Main MenuTable of Contentsst04/12/03 16:27:58 31SJC600 0080
Headlights, Instrument Panel Brightness
Daytime Running Lights Canadianmodelsonly With the headlight control dial off, the high beam headlights and the high beam indicator come on with reduced brightness when you turn the ignition switch to ON (II) and release the parking brake. They remain on until you turn the ignition switch off, even if you set the parking brake.
The headlights revert to normal operation when you turn them on with the headlight control dial.
Instrument Panel Brightness
INSTRUMENT PANEL BRIGHTNESS CONTROL DIAL
The dial on the instrument panel controls the brightness of the instrument panel lights and the console compartment light. Turn the dial to adjust the brightness.
The instrument panel will illuminate with reduced brightness when you unlock and open the driver’s door. The brightness will increase slightly when you insert the key in the ignition switch, then go to normal
brightness when you turn the ignition switch to ON (II).
If you do not insert the key in the ignition switch after opening the driver’s door, the illumination turns off about 30 seconds after you close the door.
If you insert the key but do not turn
the ignition switch to ON (II), the
illumination turns off in about 10
seconds.
The instrument panel brightness is dimmed when you turn the headlight control dial to ‘‘ ‘‘ night. To cancel it, turn the instrument panel brightness control dial upward fully until you hear a click.
’’ position to reduce glare at
’’ or
75
Main MenuTable of Contentsst04/12/03 16:28:09 31SJC600 0081
Hazard Warning Button, Steering Wheel Adjustment
Hazard Warning Button
Steering Wheel Adjustment Make any steering wheel adjustment before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
3.
Push the lever up to lock the steering wheel in position.
Push the lever on the left side of the steering column all the way down.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up and down.
Move the steering wheel so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
Push the red button to turn on the hazard warning lights (four-way flashers). This causes all four outside turn signals and both turn indicators in the instrument panel to flash. Use the hazard warning lights if you need to park in a dangerous area near heavy traffic, or if your vehicle is disabled.
1.
2.
76
Main MenuTable of Contentsst04/12/03 16:28:18 31SJC600 0082
KEY NUMBER TAG
MASTER KEY WITH REMOTE TRANSMITTER
VALET KEY (LIGHT GRAY)
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
Keys
The master key fits all the locks on your vehicle. The valet key works only in the ignition and the driver’s door lock. You can keep the glove boxlockedwhenyouleaveyour vehicle and the valet key at a parking facility.
You can also keep the In-Bed Trunk locked by using the main switch in the glove box (see page
94
).
Protect the keys from direct sunlight, high temperature, and high humidity.
Donotdropthekeysorsetheavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
77
Main MenuTable of Contentsst04/12/03 16:28:27 31SJC600 0083
Immobilizer System
The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to ON (II), the immobilizer system indicator should come on for a few seconds, then go out. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to LOCK (0), remove the key, reinsert it, and turn the switch to ON (II) again.
78
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key chain) is near the ignition switch when you insert the key.
If the system repeatedly does not recognize the coding of your key, contact your dealer.
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undriveable.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
If you have lost your key and you cannot start the engine, contact your dealer.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
Main MenuTable of Contentsst04/12/03 16:28:37 31SJC600 0084
Ignition Switch
The ignition switch has four positions: LOCK (0), ACCESSORY (I), ON (II), and START (III).
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, the shift lever must be in Park, and you must push the key in slightly.
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
−
You can
ACCESSORY (I) operate the audio system and the accessory power sockets in this position.
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from ACCESSORY (I) to ON (II).
−
Use this position
START (III) only to start the engine. The switch returns to ON (II) when you let go of the key.
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver’s door. Remove the key to turn off the beeper.
The shift lever must be in Park before you can remove the key from the ignition switch.
79
Main MenuTable of Contentsst04/12/03 16:28:47 31SJC600 0085
Door Locks
Power Door Locks
LOCK TAB
MASTER DOOR LOCK SWITCH
To lock all doors and the In-Bed Trunk, push the front of the master door lock switch on either front door, pressthelocktabdownonthe driver’s door, or use the key on the outside lock on the driver’s door.
Pushing the rear of either master door lock switch will unlock all of the doors and the In-Bed Trunk.
80
The lock tab on each door locks and unlocks that door. Pulling up on the driver’s door lock tab only unlocks the driver’s door. To unlock the driver’s door from the outside, turn the key and release it. If you turn it again, unlock all doors and the In-Bed Trunk.
To lock any passenger’s door when getting out of the vehicle, push the lock tab down, and close the door. To lock the driver’s door, remove the key from the ignition switch, and push the lock tab down, or push the front of the master switch, then close the door.
Youcanopenorclosetheside windows by using the key in the driver’s door (see page
104
).
LockoutPrevention With the driver’s door open and the key in the ignition, both master door lock switches are disabled. They are not disabled if the driver’s door is closed. Pushing the front of the switch on the open passenger’s door will lock all doors and the In-Bed Trunk.
This vehicle has auto door locking/ unlocking features. See page for how to set them.
81
Main MenuTable of Contentsst04/12/03 16:29:00 31SJC600 0086
Childproof Door Locks
LOCK LEVER
The childproof door locks are designed to prevent children seated in the rear from accidentally opening the rear doors. Each rear door has a lock lever near the edge. With the lever in the LOCK position, the door cannot be opened from the inside regardless of the position of the lock tab. To open the door, pull the lock tab up, and use the outside door handle.
Auto Door Locking/Unlocking Your vehicle has two custom door lock settings: auto door locking and auto door unlocking. Make all settings before you start driving.
With the auto door locking and unlocking, the In-Bed Trunk also locks and unlocks.
Auto Door Locking The auto door locking feature has three possible settings:
The doors lock whenever you move the shift lever out of the Park position.
The doors lock when the vehicle speed reaches 9 mph (15 km/h).
The auto door locking is deactivated all the time.
Door Locks
Toactivateeitherautodoorlock mode: Locksalldoorswhentheshiftleveris movedoutofPark(P).
1.
Make sure the shift lever is in Park (P), and close the driver’s door.
2.
Turn the ignition switch to ON (II).
CONTINUED
81
Main MenuTable of Contentsst04/12/03 16:29:11 31SJC600 0087
Door Locks
3.
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and after about 5
seconds, you will hear another
clicking sound.
4.
Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.
82
4.
5.
Push and hold the brake pedal, then move the shift lever out of Park (P).
Push and hold the front of the
master door lock switch on the
driver’s door. You will hear a
clicking sound, and after about 5
seconds, you will hear another
clicking sound.
6.
Release the switch, move the shift lever to Park (P), and turn the ignition switch to LOCK (0) within 5 seconds.
Locksalldoorswhenthevehicle’sspeed reachesabout9mph(15km/h).
1.
Make sure the shift lever is in Park (P), and close the driver’s door.
2.
Turn the ignition switch to ON (II).
3.
Set the parking brake.
Main MenuTable of Contentsst04/12/03 16:29:23 31SJC600 0088
Toturntheautodoorlockmodes off:
4.
Push and hold the front of the
master door lock switch on the
driver(cid:146)s door. You will hear a
clicking sound after about 5
seconds.
5.
Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.
1.
Make sure the shift lever is in Park (P), and open the driver(cid:146)s door.
2.
Turn the ignition switch to ON (II).
3.
Set the parking brake.
Door Locks
Auto Door Unlocking The auto door unlocking feature has five possible settings:
The driver’s door unlocks when you move the shift lever to the Park position.
The driver’s door unlocks when- ever you turn the ignition switch to LOCK (0).
All doors unlock when you move the shift lever to the Park position.
All doors unlock whenever you turn the ignition switch to LOCK (0).
The auto door unlocking is deactivated all the time.
CONTINUED
83
Main MenuTable of Contentsst04/12/03 16:29:35 31SJC600 0089
Door Locks
Toactivate autodoor unlock mode: Unlocks driver’s door or all doors when shift lever is moved to Park (P).
1.
Make sure the shift lever is in Park (P), and close the driver(cid:146)s door.
2.
Turn the ignition switch to ON (II).
84
3.
Push and hold the rear of the master door lock switch on the driver(cid:146)s door. You will hear a clicking sound. Continue to hold down the switch:
- Until you hear one click (after about 5 seconds) to activate the driver’s door unlock feature.
- Or, until you hear a second click (after about 10 seconds) to activate the all door unlock feature.
4.
Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.
Unlocks driver’s door or all doors when the ignitionswitch is out of the ON (II) position.
1.
Make sure the shift lever is in Park (P), and close the driver(cid:146)s door.
2.
Turn the ignition switch to ON (II).
3.
Set the parking brake.
4.
Push and hold the brake pedal, then move the shift lever out of Park (P).
Main MenuTable of Contentsst04/12/03 16:29:44 31SJC600 0090
5. Push and hold the rear of the
master door lock switch on the driver(cid:146)s door. You will hear a clicking sound. Continue to hold down the switch:
- Until you hear one click (after about 5 seconds) to activate the driver’s door unlock feature.
- Or, until you hear a second click (after about 10 seconds) to activate the all door unlock feature.
6.
Release the switch, move the shift lever to Park (P), and turn the ignition switch to LOCK (0) within 5 seconds.
Toturntheautodoorunlockmodes off:
1.
Make sure the shift lever is in Park (P), and open the driver(cid:146)s door.
2.
Turn the ignition switch to ON (II).
3.
Set the parking brake.
Door Locks
4.
Push and hold the rear of the
master door lock switch on the
driver(cid:146)s door. You will hear a
clicking sound after about 5
seconds.
5.
Release the switch, and turn the ignition switch to LOCK (0) within 5 seconds.
If your vehicle(cid:146)s battery is removed or goes dead, the auto door lock/ unlock setting is reset to the deactivated mode.
85
Main MenuTable of Contentsst04/12/03 16:29:52 31SJC600 0091
−
Press this button once
UNLOCK to unlock the driver’s door. Push it twice to unlock the other doors and the In-Bed Trunk. Some exterior and interior lights will flash twice each time you push the button.
When you press the UNLOCK button, the front and rear individual map lights, depending on the interior light control switch position, will come on (see page ). If you do not open any door, the lights stay on for about 30 seconds, then go out. If you relock the doors and the In-Bed Trunk with the remote transmitter before 30 seconds have elapsed, the lights will go off immediately.
115
Remote Transmitter
LED
LOCK BUTTON
UNLOCK BUTTON
PANIC BUTTON
−
LOCK
Press this button once to
lock all doors and the In-Bed Trunk.
Some exterior and interior lights will
flash once.
When you push LOCK twice within 5
seconds, you will hear a beep to
verify that the doors and In-Bed
Trunk are locked and the security
system (if equipped) has set. This
button does not work if any door is
not fully closed or the key is in the
ignition switch.
86
If you do not open any door within 30
seconds, the doors automatically
relock, and the security system sets
(if equipped). The UNLOCK button
does not work when the key is in the
ignition switch.
You can also open all side windows
from outside the vehicle with the
104
remote transmitter (see page
).
−
Press and hold this
PANIC button for about 1 second to attract attention; the horn will sound and the exterior lights will flash for about 30 seconds. To cancel panic mode, press any other button on the remote transmitter, or turn the ignition switch to ON (II). Panic mode does not work when the key is in the ignition switch.
Main MenuTable of Contentsst04/12/03 16:30:07 31SJC600 0092
Remote Transmitter Care
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
Remote Transmitter
Replacing the Transmitter Battery
BATTERY
SCREW
If it takes several pushes on the
button to lock or unlock the doors,
replace the battery as soon as
possible.
Battery type: CR1616
2.
3.
To replace the battery:
1.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
Separate the transmitter by prying its middle seam with your fingernail.
Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
CONTINUED
87
Main MenuTable of Contentsst04/12/03 16:30:13 31SJC600 0093
Remote Transmitter
AsrequiredbytheFCC: ThisdevicecomplieswithPart15ofthe FCCrules.Operationissubjecttothe followingtwoconditions:(1)Thisdevice maynotcauseharmfulinterference,and (2)thisdevicemustacceptany interferencereceived,including interferencethatmaycauseundesired operation.
Changesormodificationsnotexpressly approvedbythepartyresponsiblefor compliancecouldvoidtheuser’s authoritytooperatetheequipment.
ThisdevicecomplieswithIndustry CanadaStandardRSS-210. Operationissubjecttothefollowingtwo conditions:(1)thisdevicemaynotcause interference,and(2)thisdevicemust acceptanyinterferencethatmaycause undesiredoperationofthedevice.
4.
Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the
side facing down.
+
5.
Install the parts in reverse order.
88
Main MenuTable of Contentsst04/12/03 16:30:24 31SJC600 0094
Before you open the tailgate a different way (dropped open, and then swung open), make sure it is fully closed.
Make sure all passengers and objects are clear of the tailgate before opening and closing it, and make sure the tailgate is closed securely before driving.
You can open the tailgate two different ways:
Drop it open by using the upper handle.
Swing it open by using the right lower handle.
NOTE: As a safety feature, the upper handle is disabled if you do not fully close the tailgate after it is swung open. And the lower handle is disabled if you do not fully close the tailgate after it is dropped open.
Dual-Action Tailgate
To Drop Open the Tailgate
UPPER HANDLE
To drop open the tailgate, pull up the upper handle, then pull down the tailgate. To close the tailgate, push firmly up until it latches.
CONTINUED
89
Main MenuTable of Contentsst04/12/03 16:30:33 31SJC600 0095
Dual-Action Tailgate
The dropped open tailgate can be used as an extended pickup bed. Make sure to secure the items in the pickup bed, and do not exceed the maximum allowable weight on the tailgate(seepage
185
).
To Swing Open the Tailgate
To turn the bed lights on or off, use the bed light switch on the dashboard (see page ).
117
HANDLE
To swing open the tailgate, first make sure it is fully closed, then pull up the right lower handle, and swing the tailgate to the left. To close, swing the tailgate back, and push it firmly until it is latched.
Before opening or closing the tailgate, check that passengers, especially children, are not in the tailgate’s path.
90
Do not drive with the tailgate swung open. This could damage the tailgate.
Swinging the tailgate open or closed while anyone is in its path can cause serious injury.
Make sure all passengers are clear of the tailgate’s path before opening or closing it.
Main MenuTable of Contentsst04/12/03 16:30:43 31SJC600 0096
Do not allow anyone to hang on the swung open tailgate. This could damage the tailgate.
Do not leave the tailgate swung open. The tailgate may swing and shut accidentally. This could cause serious injuries.
Thebedlightscomeonwhenyou swing open the tailgate. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page
117
).
TailgateOpenIndicator
This indicator is in the door and tailgate open monitor on the instrument panel. It comes on when the tailgate is swung open or it is not completely closed. This indicator worksevenifthekeyisnotinthe ignition switch.
If the tailgate is swung open or not closed tightly when the ignition switch is in the ON (II) position, you will hear six beeps and see the indicator blinking. The indicator stays on until you close the tailgate. The beeper also sounds and the indicator blinks when you move the shift lever out of the Park or neutral position.
Dual-Action Tailgate
If you do not fasten the seat belt, you first hear the seat belt reminder alarm, then the tailgate reminder beeper sounds.
The indicator does not monitor the tailgate when it is dropped open.
Loading Cargo See page for information on cargo loading and weight limits.
183
You can also store and lock items in the In-Bed Trunk (see page
92
).
91
Main MenuTable of Contentsst04/12/03 16:30:53 31SJC600 0097
In-Bed Trunk
TM
If your vehicle’s battery is disconnected or goes dead, the release button on the In-Bed Trunk lid is disabled. To open the In-Bed Trunk, use the master key.
Thebedlightscomeonwhenyou open the In-Bed Trunk. You can also turn the bed lights on or off by pushing the bed light switch on the dashboard (see page
117
).
You can store items in the In-Bed
Trunk up to 300 lbs (136 kg). Do not
exceed this weight limit, or you may
damage the In-Bed Trunk. See page
183
for information on loading cargo
and weight limits.
To store items separately in the In-Bed Trunk, optional divider guides are available from your dealer.
To close the In-Bed Trunk, lower the lid, then press down on the back edge.
When the In-Bed Trunk is closed securely, it can be locked or unlocked along with the power door locks (see page
80
).
RELEASE BUTTON
YoucanopentheIn-BedTrunktwo different ways:
Push the release button on the lower right side of the In-Bed Trunk lid when the driver’s door is unlocked.
Usethemasterkeytoopenthe In-Bed Trunk when the driver’s door is locked.
92
Main MenuTable of Contentsst04/12/03 16:31:05 31SJC600 0098
To avoid damaging the key and key cylinder of the In-Bed Trunk lid, do notclosethetailgatewhenthekeyis in the lid.
To avoid damaging the seal on the In-Bed Trunk lid, remove any debris from the lid’s mating surface before you close it.
Emergency Opener
In-Bed Trunk
TM
To avoid damaging the In-Bed Trunk lid, and to prevent items from being thrown about the vehicle and possibly hurting someone in an accident or sudden stop, be sure the In-Bed Trunk lid is securely closed before driving away.
To avoid damaging the bottom of the In-Bed Trunk, do not drive over large obstacles, and do not use it as a jacking point to raise the vehicle.
In-Bed Trunk Open Indicator
This indicator on the instrument panel reminds you that the In-Bed Trunk is open (see page
66
).
As a safety feature, your vehicle has a release lever on the latch of the In-Bed Trunk lid so it can be opened from the inside. To open the In-Bed Trunk, push the release lever in the direction of the arrow.
Parents should decide if their children should be shown how to use this feature. For more information about child safety, see page
34
93
Main MenuTable of Contentsst04/12/03 16:31:15 31SJC600 0099
In-Bed Trunk
TM
In-Bed Trunk Main Switch
Washing the In-Bed Trunk
Cargo Hooks
MAIN SWITCH
CARGO HOOKS
To protect items in the In-Bed Trunk, you can disable its release button by turning off the main switch in the glove box and locking the glove box with the master key.
Even if the main switch is in the OFF position, you can open the In-Bed Trunk with the master key.
94
DRAIN PLUG
You can wash the inside of the In-Bed Trunk with a water and mild detergent solution, and a soft brush or cloth.
To drain water from the In-Bed Trunk, remove the drain plug by turning it counterclockwise.
When you are finished washing the In-Bed Trunk, dry it with a soft cloth, and reinstall the drain plug.
There are two cargo hooks for plastic grocery bags at the back of the In-Bed Trunk. They are designed to hold light items. Heavy objects may damage the hooks.
Main MenuTable of Contentsst04/12/03 16:31:25 31SJC600 0100
All models except the RT and the Canadian LX have a power adjustable driver’s seat. The RT/LX model has manual driver’s seat adjustments (see the next column).
The front passenger’s seat in all models adjusts manually.
−
11 13
Manual Seat Adjustments See pages for important safety informationandwarningsabouthowto properlypositiontheseatsandseat- backs. Make all seat adjustments before you start driving.
To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat to make sure it is locked in position.
Seats
To change the seat-back angle of the front seat, pull up on the lever on the outside of the seat bottom.
Once your seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
95
Main MenuTable of Contentsst04/12/03 16:31:33 31SJC600 0101
Seats
Driver’s Seat Manual Height Adjustment Make all seat adjustments before you start driving.
OnRTandCanadianLXmodels The height of your driver’s seat is adjustable. To raise the seat, repeatedly pull up the lever on the outside of the seat cushion. To lower the seat, push the lever down repeatedly.
96
Make sure to pull the lever upward or downward to its full range.
Driver’s Manual Lumbar Support
OnRTSmodel Vary the lumbar support by moving the lever on the right side of the seat-back. Move the lever forward or backward to adjust the lumbar support through its full range.
Main MenuTable of Contentsst04/12/03 16:31:46 31SJC600 0102
Power Seat Adjustments OnallmodelsexceptRTand CanadianLX Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.
11 13
−
The controls for the power adjustable driver’s seat are on the outside edge of the seat bottom. You can adjust the seat with the ignition switch in any position. Make all seat adjustments before you start driving.
Moving the long horizontal switch adjusts the seat bottom in several directions. The seat bottom adjusts in the direction you move the switch. The short vertical switch adjusts the seat-back angle.
Moves the seat forward and backward.
Moves the front of the seat up or down and the rear of the seat up or down.
Raises or lowers the seat.
Seats
Adjusts the seat-back angle forward or backward.
Increases or decreases the lumbar support. (RTL and Canadian EXL models)
97
Main MenuTable of Contentsst04/12/03 16:31:52 31SJC600 0103
Seats
Armrests
FRONT
REAR
To use the console lid as an armrest, slide it to the desired position.
Make sure your passenger’s hands or fingers are away from the armrest before moving it.
The rear seat armrest is in the center of the rear seats. Pivot it down to use it.
98
Main MenuTable of Contentsst04/12/03 16:32:01 31SJC600 0104
Head Restraints See page for important safety informationandawarningabouthowto properlypositiontheheadrestraints.
13
Your vehicle is equipped with head restraints in all seating positions to help protect you and your passengers from whiplash and other injuries.
They are most effective when you adjust them so the back of the occupant’s head rests against the center of the restraint.
Seats
Rear Center Position
RELEASE BUTTON
The head restraints adjust for height. You need both hands to adjust the restraint. Do not attempt to adjust it while driving. To raise it, pull upward. To lower the restraint, push the release button sideways and push the restraint down.
RELEASE BUTTON When carrying a passenger in the rear center seating position, make sure the rear center head restraint is adjusted to its highest position.
99
Main MenuTable of Contentsst04/12/03 16:32:09 31SJC600 0105
Seats
Folding the Rear Seats The left and right rear seat cushions can be lifted up separately to make room for cargo.
Remove any items from the seat before you fold up the seat cushion.
LEGS
To fold a rear seat cushion, pull up the lever on the outside of the cushion. The seat cushion pops up, and the seat legs store underneath it. Push the cushion firmly against the seat-back to lock it in place.
FLOOR GUIDE
To return the seat cushion to its original position, pull the lever outward, then push down the seat cushion slowly.
Make sure the seat cushion is locked securely and the seat legs are positioned properly in the floor guide.
100
Main MenuTable of Contentsst04/12/03 16:32:19 31SJC600 0106
Make sure all items in the cargo area are secured. Loose items can fly forward and cause injury if you have Carrying Cargo to brake hard (See on page
182
).
You can also store small items under the rear seats. Make sure to secure the items so they will not shift while you are driving.
Seat Heaters
SEAT HEATER SWITCHES
Ifequipped Both front seats have seat heaters. The passenger seat is only heated in the seat bottom because of the side airbag cutoff system. The ignition switch must be in the ON (II) position to use seat heaters. Push the top of the switch, HI, to rapidly heat up the seat. After the seat reaches a comfortable temperature, select LO by pushing the bottom of the switch. This will keep the seat warm.
Seats, Seat Heaters
In HI, the heater turns off when the seat gets warm, and turns back on after the seat temperature drops.
In LO, the heater runs continuously. It does not cycle with temperature changes.
Follow these precautions when using the seat heaters:
Use the HI setting only to heat the seats quickly, because it draws large amounts of current from the battery.
If the engine is left idling for an extended period, do not use the seat heaters, even on the LO setting. It can weaken the battery, causing hard starting.
101
Main MenuTable of Contentsst04/12/03 16:32:27 31SJC600 0107
Power Windows
DRIVER’S WINDOW SWITCH
MAIN SWITCH
The windows operate for up to 10
minutes after you turn off the
ignition switch. Opening either front
door cancels this function.
BACK WINDOW SWITCH
Closing a power window on someone’s hands or fingers can cause serious injury.
Make sure your passengers are away from the windows before closing them.
Turn the ignition switch to ON (II) to raise or lower any side window, or open and close the back window. To open the window, push the switch down and hold it. Release the switch when you want the window to stop. Pull back on the switch and hold it to close the window.
102
−
To open or close the
AUTO driver’s window, push or pull the window switch firmly down or up to the second detent, and release it. The window will automatically go up or down all the way. To stop the window, pull or push on the window switch briefly.
When you push the MAIN switch in, the passenger windows and the back window cannot be raised or lowered.
To cancel this feature, push on the switch again. Keep the MAIN switch off when you have children in the vehicle so they do not injure themselves by operating the windows unintentionally.
Main MenuTable of Contentsst04/12/03 16:32:38 31SJC600 0108
AUTO REVERSE − If the driver’s window senses any obstacle while it is closing automatically, it will reverse direction and then stop. To close the window, remove the obstacle, then use the window switch again.
Auto reverse stops sensing when the window is almost closed. You should always check that all passengers and objects are away from the window before closing it.
If the driver’s window fuse is removed, the AUTO function may be disabled. The power window system needs to be reset after reinstalling the fuse.
1.
2.
Start the engine. Push down and hold the driver’s window switch until the window is fully open.
Pull and hold the driver’s window switch to close the window completely, then hold the switch for a second or two more.
If the power windows do not operate properly after resetting, have your vehicle checked by your dealer.
Power Windows
Back Window Your vehicle has a power back window.
Back Window Open Indicator
This indicator comes on when you
turn the ignition switch from ON (II)
to ACCESSORY (I) or LOCK (0)
without closing the back window.
With the ignition switch in the
ACCESSORY (I) position, the
indicator goes off after about 30
seconds. With the ignition switch in
the LOCK (0) position, the indicator
goes off after about 3 minutes.
CONTINUED
103
Main MenuTable of Contentsst04/12/03 16:32:50 31SJC600 0109
Power Windows
If you remove the ignition key and
open the driver’s door without
closing the back window, you hear
five beeps and see the indicator blink.
If you do not close the back window
before the beeper stops, the
indicator stops blinking but remains
on. It will go off after about 3
minutes (see page
66
).
The back window is not designed to carry long items through it. Do not use the opened back window as a cargo area pass-through.
104
Opening the Side Windows with the Remote Transmitter You can open all of the side windows from the outside with the remote transmitter.
1.
Press the UNLOCK button once to unlock the driver’s door.
2.
Press the UNLOCK button a second time, and hold it. The passenger’s doors unlock, and all four side windows start to open. To stop the windows, release the button.
3.
To open the windows further, press the button again, within about 3 seconds.
You cannot close the windows with the remote transmitter.
UNLOCK BUTTON
Close
Open
Opening/Closing the Side Windows with the Key You can open and close the side windows with the key in the driver’s door lock.
To open: 1.
Insert the key in the driver’s door lock.
2.
Turn the key clockwise, then release it.
Main MenuTable of Contentsst04/12/03 16:33:04 31SJC600 0110
3.
Turn the key clockwise again, and hold it. All four side windows start to open. To stop the windows, release the key.
4.
To open the windows further, turn and hold the key again (within 10 seconds).
NOTE: If the windows stop before
the desired position, repeat steps 2
and 3.
To close: 1.
Insert the key in the driver’s door lock.
2.
Turn the key counterclockwise, then release it.
3.
Turn the key counterclockwise again, and hold it. All four side windows start to close. To stop the windows, release the key.
Power Windows, Moonroof
4.
To close the windows further, turn and hold the key again (within 10 seconds).
Moonroof
NOTE: If the windows stop before
the desired position, repeat steps 2
and 3.
MOONROOF SWITCH
Ifequipped The moonroof has two positions: it can be tilted up in the back for ventilation, or it can slide back into the roof. Use the switch near the left dashboard vent to operate the moonroof. The ignition switch must be in the ON (II) position.
CONTINUED
105
Main MenuTable of Contentsst04/12/03 16:33:13 31SJC600 0111
Moonroof, Parking Brake
). To close the
To tilt up the back of the moonroof, press and hold the center part of the switch ( moonroof, press and hold the upper part of the switch ( ). To open the moonroof, press and hold the lower part of the switch ( ). Release the switch when the moonroof gets to the desired position.
Make sure everyone’s hands are away from the moonroof before opening or closing it.
Opening or closing the moonroof on someone’s hands or fingers can cause serious injury.
Make sure all hands and fingers are clear of the moonroof before opening or closing it.
106
You can open and close the moonroof for up to 10 minutes after you turn off the ignition switch. Opening either front door cancels this function.
Parking Brake
RELEASE HANDLE
If you try to open the moonroof in below-f reezing temperatures, or when it is covered with snow or ice, you can damage the moonroof panel or its motor.
PARKING BRAKE PEDAL
To apply the parking brake, push the pedal down with your foot. To release it, pull the release handle fully. The parking brake indicator on the instrument panel should go out when the parking brake is fully released, and the ignition switch is in the ON (II) position (see page
60
).
Main MenuTable of Contentsst04/12/03 16:33:22 31SJC600 0112
Parking Brake, Mirrors
Ifequipped Therearviewmirrorhasacompass function to indicate the vehicle’s direction. Refer to
Compass
on page
166
Mirrors
TAB
Driving the vehicle with the parking brake applied can damage the rear brakes and axles. A beeper will sound if the vehicle is driven with the parking brake on.
Keeptheinsideandoutsidemirrors clean and adjusted for best visibility. Be sure to adjust the mirrors before you start driving.
The inside mirror has day and night positions. The night position reduces glare from headlights behind you. Flip the tab on the bottom edge of the mirror to select the day or night position.
107
Main MenuTable of Contentsst04/12/03 16:33:32 31SJC600 0113
Mirrors
AdjustingthePowerMirrors
ADJUSTMENT SWITCH
SELECTOR SWITCH
1.
Turn the ignition switch to ON (II).
2.
3.
Move the selector switch to L (driver’s side) or R (passenger’s side).
Push the appropriate edge of the adjustment switch to move the mirror right, left, up, or down.
108
4.
When you finish, move the selector switch to the center (off) position. This turns the adjustment switch off to keep your settings.
HeatedMirrors
HEATED MIRROR BUTTON
Ifequipped The outside mirrors are heated to remove fog and frost. With the ignition switch in the ON (II) position, turn on the heaters by pressing the button. The indicator in the button comes on as a reminder. Press the button again to turn the heaters off.
Main MenuTable of Contentsst04/12/03 16:33:38 31SJC600 0114
VANITY MIRROR
SUN VISOR
CENTER CONSOLE
CONSOLE COMPARTMENT
Interior Convenience Items
SUNGLASSES HOLDER
CENTER UPPER POCKET *
GLOVE BOX
ACCESSORY POWER SOCKETS CENTER POCKET
BEVERAGE HOLDER
COAT HOOK
ACCESSORY POWER SOCKET
CENTER LOWER POCKET
BEVERAGE HOLDERS
*
: On vehicle without navigation system
109
Main MenuTable of Contentsst04/12/03 16:33:48 31SJC600 0115
Interior Convenience Items
Center Console
ConsoleCompartments The center console main compartment is under the tray and the beverage holder. You can access the main compartment in two ways (front or rear).
Your vehicle has a multi-function center console. It includes beverage holders, storage compartments, an armrest, a coin holder, and a storage tray.
110
To open the rear of the compartment, push the button at the end of the tray, then slide the tray forward. To close, slide the tray back in place.
There are two removable partitions in the main compartment. The partitions can be used to divide the main compartment, or can be stored at the front of the compartment. The console compartment light comes on when the instrument panel lights are on.
To open the front of the compartment, squeeze the knob, and push it forward while sliding the beverage holder. To close, squeeze the knob and pull the compartment backward until the beverage holder latches.
Main MenuTable of Contentsst04/12/03 16:34:00 31SJC600 0116
CargoHooks
COIN HOLDER
You can put small items in the upper console compartment. To use it, pull up on the lever and lift up the armrest.
Ifequipped The upper console compartment has a removable coin holder. Pull the coin holder straight up to remove it. To install it, push it down along the guides on the side of the compartment.
CARGO HOOKS
There are two cargo hooks for plastic grocery bags at the back of the center console. They are designed to hold light items. Heavy objects may damage the hooks.
Interior Convenience Items
Beverage Holders The center console has two beverage holders on the front. Your vehicle also has beverage holders in the rear seat armrest and the rear door panels.
Be careful when you are using the beverage holders. A spilled liquid that is very hot can scald you or your passengers. Liquid can also spill from the door panel beverage holders when you close the doors. Use only resealable containers in the door beverage holders.
Spilled liquids can damage the