2007 Honda CR V Owners Manual

MIDDLE SEGMENT

LOWER SEGMENT

MIDDLE SEGMENT

LOWER SEGMENT

Left-hand drive type

Right-hand drive type

The multi-information display consists of an upper segment, a middle segment and a lower segment. Each segment can display two lines of messages.

In normal display mode, the upper and middle segments display the trip computer and the rear seat belt use, and the lower segment displays the odometer, trip meter, and outside temperature.

06/09/13 17:07:21 32SWA600_110

INFO BUTTON

SEL/RESET BUTTON

On vehicles with cruise control

The trip computer consists of the current fuel mileage, the average fuel economy, the estimated distance, the elapsed time, and the average speed. The upper segment always displays one of the trip computer items as a primary display, and the middle segment shows what you last selected when you turn the ignition switch to the ON (II) position. You can customize it to your preference

INFO BUTTON

SEL/RESET BUTTON On vehicles with adaptive cruise control (ACC)

(see page

148

).

In the middle segment, the rear seat belt use is also displayed.

In the default setting, the upper display shows the current fuel mileage when you turn the ignition switch to the ON (II) position. The remaining trip computer items are displayed in the middle segment.

Multi-Information Display

Each time you press the INFO button, the trip computer changes from the average fuel economy to the estimated distance to the elapsed time to the average speed and then to the rear seat belt use as shown on the next page.

If there is any system warning, system warning symbol(s) will be shown on the multi-information display following the speed alarm setting. The system warning symbol/message that has the highest priority will be displayed first when you turn the ignition switch to the ON (II) position.

CONTINUED

Instruments and Controls 105

06/09/13 17:07:27 32SWA600_111

Multi-Information Display

Left-hand drive type

Right-hand drive type

If you select the blank display in the middle segment, the upper display will also change to the blank display. 106

Instruments and Controls

06/09/13 17:07:40 32SWA600_112

Indicators in the trip computer show:

Left-handdrivetype

: Your vehicle’s current fuel mileage in kilometers per hour and l/100 km.

Right-handdrivetype

: Your vehicle’s current fuel mileage in miles per hour and mpg.

The display may show a current fuel mileage reading higher than in normal driving while the particulate matter (PM) is burnt and removed from the diesel particulate filter (DPF). For more information, see page

534

Multi-Information Display

: The estimated distance you

can travel on the fuel remaining in the tank. This distance is estimated from the fuel economy you have achieved over the last few kilometers (miles), so it will vary with changes in speed, traffic condition, etc.

: The average speed you are travelling is displayed in kilometres per hour (km/h) or miles per hour (mph) depending on the model.

: Your vehicle’s average fuel mileage since you last reset the trip computer A.

: The time travelled since

you last turned the ignition switch to the ON (II) position.

: Your vehicle’s average fuel mileage since you last reset the trip computer B.

The average fuel mileage is updated once per 10 seconds. When you reset a trip meter, the average fuel mileage for that trip meter also resets. To reset the values in the trip computer, press and hold the SEL/ RESET button until the number resets to ‘‘0.0.’’

CONTINUED

Instruments and Controls 107

’’ or ‘‘

’’ will be

‘‘ displayed when the average fuel mileage is selected in the upper segment, depending on which trip meter (trip A or trip B) is displayed in the lower segment.

06/09/13 17:07:50 32SWA600_113

Multi-Information Display

Odometer The odometer shows the total number of kilometers or miles your vehicle has been driven.

TripMeter This meter shows the number of kilometers or miles driven since you last reset it.

There are two trip meters: trip A and trip B. To switch the display between them, press the SEL/RESET button repeatedly. When you turn the ignition switch to the ON (II) position, what you last selected is displayed.

Each trip meter works independently, so you can keep track of two different distances.

To reset a trip meter, display it, and then press and hold the SEL/RESET button until the number resets to ‘‘0.0.’’

TRIP METER ODOMETER

OUTSIDE TEMPERATURE INDICATOR Left-hand drive type is shown.

The lower segment always shows the odometer, trip meter and the outside temperature in the normal display mode.

108

Instruments and Controls

06/09/13 17:07:57 32SWA600_114

OutsideTemperatureIndicator This indicator displays the outside temperature in degrees Centigrade.

The temperature sensor is in the front bumper. Therefore, the temperature reading can be affected by heat reflection from the road surface, engine heat, and the exhaust from surrounding traffic. This can cause an incorrect temperature reading when your speed is under 30 km/h (19 mph).

The sensor delays the display update until it reaches the correct outside temperature. This may take several minutes.

If the outside temperature is incorrectly displayed, you can adjust it by up to (see page

3°C warmer or cooler ).

± 146

NOTE: The temperature must be stabilized before doing this procedure.

In certain weather conditions, temperature readings near freezing (0°C) could mean that ice is forming on the road surface. You will also see a caution symbol on the multi- information display (see page

119

).

Multi-Information Display

Instruments and Controls

109

06/09/13 17:08:04 32SWA600_115

Multi-Information Display

System Warning Symbols If there is a problem with your vehicle, for example, the engine oil level is low or a door is not fully closed, the multi-information display will show you the problem. It does this by interrupting the current display with one or more symbols/ messages. Most of the symbols/ messages are displayed for about 5
seconds, and then the current display returns. Some symbols/ messages stay on until the problem is corrected.

When your vehicle is new, the multi- information display shows the system warning symbols without the message. This is the default setting when the vehicle leaves the factory. You can customize this setting to see the system warning symbols with messages (see page ). Some symbols such as the low outside temperature, rear seat belt reminder indicator, etc., do not have a

145

110

Instruments and Controls

message.

In this section, the system symbol without message is used in almost all examples, and the same symbol(s) are used for a message.

Usually, the symbols/messages are shown in the upper and middle segments. If the adaptive cruise control (ACC) or the collision mitigation brake system (CMBS) is selected, only the symbols are displayed in the middle segment and the ACC or CMBS information is displayed in the upper segment.

SYSTEM MESSAGE INDICATOR

These symbols/messages also trigger the appropriate indicator(s) on the instrument panel and cause the system message indicator to come on. The system message indicator does not go off until the problem(s) are corrected.

The following pages describe each system warning symbol/message that can be displayed. Here is a list of all messages:

06/09/13 17:08:16 32SWA600_116

See pages 122, 508 and

509.

See pages 122 and 503.

See pages 122 and 512.

See pages 121 and 505.

See pages 123 and 506.

See pages 89 and 126.

See pages 125 and 507.

See pages 123 and 511.

See pages 35 and 125.

See pages 125 and 366.

Multi-Information Display

See pages 117 and 214.

See pages 118 and 421.

See pages 126 and 358.

See pages 126 and 378.

See pages 123 and 391.

CONTINUED

Instruments and Controls 111

06/09/13 17:08:28 32SWA600_117

Multi-Information Display

See pages 24 and 114.

See pages 24 and 114.

See pages 25 and 115.

See pages 127 and 168.

See pages 128 and 285.

See pages 291 and 301.

See pages 286, 301 and

371.

See pages 120 and 289.

See pages 120 and 289.

See pages 128 and 368.

See page

369.

See pages 128 and 303.

See pages 124 and 535.

See pages 124 and 536.

See page

116.

112

Instruments and Controls

06/09/13 17:08:36 32SWA600_118

Multi-Information Display

See pages 94 and 118.

See pages 117 and 177.

See pages 127 and 426.

See pages 109 and 119.

See pages 127 and 165.

See pages 119 and 133.

See pages 119 and 133.

Petrol models See pages 96 and 118.

Diesel models See pages 96 and 118.

Instruments and Controls

113

06/09/13 17:08:43 32SWA600_119

Multi-Information Display

Fasten Seat Belt

Fasten Passenger Seat Belt

For more information of the seat belt reminder indicator, see page

.24

In addition to the seat belt reminder indicator in the instrument panel, the current display is interrupted and the multi-information display shows this symbol ‘‘ ,’’ or this symbol with a ‘‘FASTEN SEAT BELT’’ message if you do not fasten your seat belt while driving. This symbol/message remains displayed if you ignore it and do not wear your seat belt while the vehicle is moving.

The multi-information display also interrupts the current display and shows this symbol ‘‘ ,’’ or this symbol with a ‘‘FASTEN PASSENGER SEAT BELT’’ message if a front seat passenger does not fasten their seat belt while driving. This symbol/message remains displayed if a passenger ignores it and does not wear the seat belt while the vehicle is moving.

114

Instruments and Controls

06/09/13 17:08:51 32SWA600_120

Rear Seat Belt Use Monitor When you turn the ignition switch to the ON (II) position, the middle segment of the multi-information display shows the rear seat belt use.

This monitor goes off after about 30
seconds. It will also go off when you change the display by pressing the INFO button ( ) on the steering wheel.

Multi-Information Display

Seat belts in right and centre positions are used.

The system shows you how many rear seat belts are being used and reminds you and your passengers to fasten their seat belts. According to the rear seat belt use (1 through 3), you will see the indicator(s) highlighted on the right side of the middle segment.

CONTINUED

Instruments and Controls 115

The seat belt system detects any seat belt use of all three rear seat seating positions according to the activation of each seat belt retractor.

06/12/07 11:37:26 32SWA600_121

Multi-Information Display

The seat belt indicator system judges the use of the seat belt based on the amount of seat belt pulled out from the retractor. It is not an indicator to show that the seat belt is actually latched. Correct latching of the seat belts should be confirmed whenever the indicator shows a seat belt is in use.

While driving, you can also confirm the rear seat belt use. Press and release the INFO button ( repeatedly to change the display.

116

Instruments and Controls

Door and Tailgate Open

This shows all doors and tailgate open.

If the tailgate or any door(s) is not closed tightly, this monitor display indicates you which door or the tailgate is not closed tightly, and reminds you to close the tailgate or the door(s) before you start driving. This display continues until you close the door(s) and the tailgate.

If the system cannot detect the seat belt use, you will see three dashes. Turn the ignition switch to the LOCK (0) position to reset the system. If this happens, the SRS indicator also comes on. Have your vehicle checked by your dealer (see page

35

).

06/09/13 17:09:04 32SWA600_122

Pressing the INFO button on the steering wheel momentarily changes the display, but it will come back after about 5 seconds.

Release Parking Brake

Ignition Key

Multi-Information Display

If you start driving without releasing the parking brake, the current display is interrupted and the multi- information display shows this symbol, or this symbol with a ‘‘RELEASE PARKING BRAKE’’ message. This symbol/message continues, and a chime sounds, until you release the parking brake.

If you leave the key in the ignition switch in the LOCK (0) or ACCESSORY (I) position and open the driver’s door, you will see this symbol, or this symbol with/a ‘‘IGNITION KEY’’ message in the display and hear a reminder beeper.

Instruments and Controls 117

06/09/13 17:09:13 32SWA600_123

Multi-Information Display

Brake Fluid Low

Fuel Low

Diesel Fuel Low

Onpetrolmodels If the level of the fuel in the tank gets low, you will see this symbol, or this symbol with a ‘‘FUEL LOW’’ message on the display, and you must refuel soon. The low fuel indicator in the instrument panel will also come on (see page

96

).

If the brake fluid level is at or below the MIN mark on the side of the brake fluid reservoir in the engine compartment, you will see this symbol, or this symbol with a ‘‘BRAKE FLUID LOW’’ message. If you see this message, have the brake system checked by your dealer (see page

421

).

118

Instruments and Controls

Ondieselmodels If the level of the fuel in the tank gets low, you will see this symbol, or this symbol with a ‘‘DIESEL FUEL LOW’’ message on the display, and you must refuel soon. The low fuel indicator in the instrument panel will also come on (see page

96

).

06/09/13 17:09:20 32SWA600_124

Headlights On

Speed Alarm

Low Outside Temperature

Multi-Information Display

Alarm at vehicle speed 80 km/h is set.

If you set the speed alarm function in the custom settings, you will see this indicator and hear a beep when the vehicle speed reaches the set speed. You can set two different speeds for the alarm. For more information to set the speed alarm, see page 133

If you turn the ignition switch to the ACCESSORY (I) or LOCK (0) position without turning off the headlights or position lights, and open the driver’s door, you will see this symbol, or this symbol with a ‘‘HEADLIGHTS ON’’ message on the display. The lights on indicator in the instrument panel also comes on and stays on. You will also hear a reminder chime.

If the outside temperature is very low (near freezing) and there is a risk that the road surface is iced over, you will see this symbol on the multi- function display. For more information of the outside temperature indicator, see page

109

Instruments and Controls 119

06/09/13 17:09:25 32SWA600_125

Multi-Information Display

Shift Up/Shift Down Indications

Shift up

Shift down

Onvehicleswithadaptivecruisecontrol (ACC) Manualtransmissiononly Either the shift up or shift down indication comes on to show you the appropriate time to change a higher or lower gear when the adaptive cruise control system is activated. For more information, see page

289

120

Instruments and Controls

06/09/13 17:09:32 32SWA600_126

Check Engine Oil Level

SystemWarnings The following symbols/messages indicate various problems in your vehicle’s systems.

You will also hear a beep when the symbol or the symbol with a message is displayed on the multi- information display at the first time.

Multi-Information Display

If you ignore the oil level symbol/ message and keep driving with this symbol/message on, you can seriously damage the engine.

If this symbol or this symbol with a ‘‘CHECK ENGINE OIL LEVEL’’ message comes on on the multi- information display when the engine is running, the engine oil level is low. You will also hear a beep with this symbol/message on. You should check the oil level and add engine oil. For more information, see page

505

CONTINUED

Instruments and Controls 121

06/09/13 17:09:40 32SWA600_127

Multi-Information Display

Oil Pressure Low

Check System (Engine)

Check System (Brake)

If the engine oil is very low or has lost pressure, you will see this symbol or this symbol with an ‘‘OIL PRESSURE LOW’’ message on the multi-information display. You will also see the low oil pressure indicator in the instrument panel flashing or staying on. If you see this symbol/message, you should take immediate action since serious engine damage is possible. Follow the procedure on page

503

122

Instruments and Controls

If you see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display, it means one of the engine’s emissions systems may have a problem. Have your vehicle checked by a dealer (see page page 509

508
on diesel models).

on petrol models and

If there is a problem with the brake system (including the front-to-rear barking distribution system), you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. The parking brake and brake system indicator in the instrument panel will also come on. For more information, see page

512

06/09/13 17:09:49 32SWA600_128

Check System (Engine Oil Level Sensor)

Check System (PGM-FI)

Check System (Trailer Stability Assist)

Multi-Information Display

If there is a problem with the engine oil level sensor system, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. If you ignore this symbol/message and continue driving, the system will be seriously damaged. For more information, see page

506

Dieselmodelsonly If there is a problem with the engine control system, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. If you ignore this symbol/message and continue driving, the engine control system will be seriously damaged. For more information, see page

511

If there is a problem with the brake lighting system, the trailer stability assist function shuts down and you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. For more information of the trailer stability assist function, see page 390

CONTINUED

Instruments and Controls

123

If you ignore this symbol/message and continue driving, the DPF and your vehicle’s emission control systems will be seriously damaged. For more information on the DPF system, see page

534

06/09/13 17:09:57 32SWA600_129

Multi-Information Display

DPF (Regeneration Required)

DPF (Check System)

DieselmodelswithDPF(Diesel ParticulateFilter) If you see this symbol or this symbol with a ‘‘DPF REGENERATION REQUIRED’’ message on the multi- information display while the engine is running, it means the diesel particulate filter (DPF) should be regenerated to remove the accumulated particulate matter (PM). For more information on the DPF system, see page

534

DieselmodelswithDPF(Diesel ParticulateFilter) If you see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display while the engine is running, it means the diesel particulate filter (DPF) is clogged with accumulated particulate matter (PM) and it should be checked, then repaired or replace. Take your vehicle to a Honda dealer as soon as possible.

124

Instruments and Controls

06/09/13 17:10:05 32SWA600_130

Check System (Charging System)

Check System (Airbag System)

Check System (ABS System)

Multi-Information Display

If you see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display, it means the battery is not being charged. For more information, see page

507

If there is a problem with your front airbags, side airbags, automatic seat belt tensioners, or side curtain airbags, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi- information display. Take your vehicle to a dealer as soon as possible (see page

35

).

If there is a problem with the anti- lock brake system (ABS), you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. Have your vehicle checked by a dealer (see page

86

).

CONTINUED

Instruments and Controls 125

06/09/13 17:10:14 32SWA600_131

Multi-Information Display

Check System (Automatic Transmission)

Check System (EPS) (For some types)

Check System (VSA)

Onvehicleswithautomatictransmission If there is a problem with the automatic transmission, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information. Avoid rapid acceleration, and have the transmission checked by a dealer as soon as possible.

126

Instruments and Controls

If there is a problem with the electric power steering (EPS) system, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ on the multi-information display. The EPS system indicator in the instrument panel will also come on. If you see this symbol/message, have the EPS system checked by your dealer. For more information, see page

89

If there is a problem with the vehicle stability assist (VSA) system, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. The VSA system and VSA activation indicators in the instrument panel will also come on. If you see this symbol/message, have the VSA system checked by your dealer. For more information, see page

378

06/09/13 17:10:23 32SWA600_132

Water In Fuel Filter

Check System (Automatic Headlights On)

Multi-Information Display

Check System (Adaptive Front Lighting System) (For some types)

Dieselmodelsonly If this symbol or this symbol with a ‘‘WATER IN FUEL FILTER’’ shows on the multi-information display, water stays in the fuel system which may cause damage to the fuel injection system. Contact your dealer as soon as possible and have the fuel filter checked to drain off water.

Onvehicleswithautomaticlighting feature If you see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display, it means there is a problem with the automatic headlights on control system. If you see this symbol/ message, have the vehicle checked by your dealer as soon as possible.

If there is a problem with the adaptive front lighting (AFS) system, the AFS indicator comes on in the instrument panel and you will also see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. For more information, see page

168

CONTINUED

Instruments and Controls 127

06/09/21 18:44:19 32SWA600_133

Multi-Information Display

Check System (Adaptive Cruise Control) (For some types)

Check System (Collision Mitigation Brake System) (For some types)

Check System (Parking Sensor System) (For some types)

If there is a problem with the adaptive cruise control (ACC) system, the ACC indicator comes on amber in the instrument panel and you will also see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. For more information, see page

285

128

Instruments and Controls

If there is a problem with the collision mitigation brake system (CMBS), the CMBS indicator comes on in the instrument panel and you will also see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information display. For more information, see page

368

If there is a problem with the parking sensor system, you will see this symbol or this symbol with a ‘‘CHECK SYSTEM’’ message on the multi-information. Have the parking sensor system checked by your dealer. For more information of how to activate the parking sensors, see page

303

06/09/13 17:10:43 32SWA600_134

Multi-Information Display

Customized Settings You can customize some of the vehicle control settings to suit your needs. The table shows the settings you can customize.

Group Setup

Menu Item

Description

SPEED ALARM (P.133)

SPEED ALARM 1 (ON/OFF, Setting) SPEED ALARM 2 (ON/OFF, Setting)

Sets the speed alarm on and changes the alarm speed setting.

SPEED ALARM 1 (ON/OFF) SPEED ALARM 2 (ON/OFF)

＊

＊

Sets the speed alarm on.

CHG SETTING (P.138)

ACC SETUP

METER SETUP

PRE-RUNNING CAR DETECT BEEP ACC DISPLAY SPEED UNIT WARNING MESSAGE ADJUST OUTSIDE TEMP. DISPLAY PRIMARY DISP. SELECTION

Sets the beep to sound when the system detects a vehicle ahead of you. Changes the displayed measurement with the ACC on. Switches warning message to be displayed or not. Changes the outside temperature reading above or below its current reading. Changes the primary displayed trip computer item in the upper segment.

TRIP A RESET WITH REFUEL ELAPSED TIME RESET

Causes trip meter A and the average fuel economy to reset when you refuel. Resets the elapsed time of your current trip.

＊ ＊ ＊

1 : 2 : 3 :

Setting is available while driving. Factory default setting Default setting is what you last selected.

Setting Option

＊

ON/OFF over 5 km/h (mph) with 5 km/h (mph) steps ON/OFF

＊

ON/OFF

＊

＊

＊

＊

3°C

km/h mph ON/OFF up to ± 0°C Current fuel mileage , Average fuel mileage, Elapsed time, Range, Average speed ON/OFF

＊

＊

＊

IGN OFF , TRIP A, TRIP B

＊

Page 133

136

141

142

145
146

148

150

151

CONTINUED Instruments and Controls 129

06/09/13 17:10:49 32SWA600_135

Multi-Information Display

Group Setup

LANGUAGE (P.154)

DEFAULT ALL (P.155)

＊

Factory default setting

Menu Item

Description

Setting Option

Changes the language used in the display.

Resets all customized settings to the factory default.

＊

ENGLISH , ITALIAN, SPANISH, GERMAN, FRENCH, PORTUGUESE CANCEL OK

＊

Page 154

155

130

Instruments and Controls

06/09/13 17:10:58 32SWA600_136

To enter the customizing mode, the vehicle must be stopped with the ignition switch in the ON (II) position and the parking brake is set on vehicles with manual transmission. If your vehicle has the automatic transmission, the shift lever should be in park. (Exceptionally, this condition is not applied on some speed alarm settings.) Press and hold the INFO button ( about 3 seconds while the multi- information display is in its normal display. Here are the settings you can customize.

) on the steering wheel for

SPEED ALARM: To set the speed alarm (see page

133

).

CHG SETTING: To change vehicle control settings (see page 138

).

LANGUAGE: To select language (see page

154

).

Multi-Information Display

Each time you press the INFO button, the display switches from ‘‘SPEED ALARM’’, ‘‘CHG SETTING’’, ‘‘LANGUAGE’’, ‘‘DEFAULT ALL’’, ‘‘EXIT’’, and then back to ‘‘SPEED ALARM’’ as shown above.

CONTINUED

Instruments and Controls 131

: Press the INFO button.

DEFAULT ALL: To return to the default settings (see page

155

).

06/09/13 17:11:07 32SWA600_137

Multi-Information Display

If you set the alarm to the specified vehicle speed while driving, select ‘‘SPEED ALARM,’’ and refer to page . Exceptionally, you can also 133
select the specified speed alarm while driving.

If you do not select any settings on the display after you press the INFO button and the setting menu is displayed, the customizing mode display will return to the normal display after about 10 seconds.

If you want to change any vehicle control settings, select ‘‘CHG SETTING,’’ and follow the instructions on page

138

Customizing is also cancelled, if you turn the ignition switch out of the ON (II) position or release the parking brake (M/T) or move the shift lever out of Park (A/T).

If you select SEL/RESET button, the normal display is shown again.

and press the

If you want the settings as they were when the vehicle left the factory, select ‘‘DEFAULT ALL,’’ as described on page

155

) on the

Use the INFO button ( steering wheel to see and scroll through the settings, and the SEL/ RESET button to enter your selections.

If you try to start driving while customizing the settings, you will see the above display a few seconds and then the customizing will be cancelled.

132

Instruments and Controls

06/09/13 17:11:14 32SWA600_138

Tosetthespeedalarmwhilethevehicle isstopped:

Speed Alarm You can access different alarm functions when the vehicle is stopped or while driving. While driving, you can select either of the two speed alarm settings. When your vehicle is stopped, you can customize the setting speed to your preference.

Multi-Information Display

Speed setting 1 off is selected.

Press and hold the INFO button to enter the customizing mode, then press and release the INFO button repeatedly to select ‘‘SPEED ALARM.’’ While the multi- information display is showing ‘‘SPEED ALARM,’’ press the SEL/ RESET button. The display changes to the setting mode.

On the left-hand drive type, you can set the speed alarm in km/h. On the right-hand drive type, you can set the speed alarm in mph. The two speed selections and the on/off setting icons are displayed.

CONTINUED

Instruments and Controls

133

06/09/13 17:11:22 32SWA600_139

Multi-Information Display

Speed setting 1: You can set the alarm on or off, and adjust the setting speeds above or below 50 km/h (30 mph).

Speed setting 2: You can set the alarm on or off, and adjust the setting speeds above or below 80 km/h (50 mph).

), the selected

Each time you press and release the INFO button ( icon is changed from set 1, to 50
km/h (30 mph), and to set 2, to 80
km/h (50 mph). Then press the INFO button again to exit.

134

Instruments and Controls

Alarm off

Alarm on

Select either of the setting modes (1
or 2), then select on or off by pressing the SEL/RESET button repeatedly.

To adjust the setting speed, select either of the setting speeds, then press and release the SEL/RESET button. The display changes to the speed setting screen.

06/09/13 17:11:28 32SWA600_140

The displayed number is the current speed setting. Select either the or icon by pressing the INFO button − repeatedly, then press the SEL/ RESET button to change the setting value.

＋

Multi-Information Display

After your selection, press and release the INFO button to move to the exit mode. Press the SEL/ RESET button to enter your setting. If you press the INFO button, the display goes back to the setting mode. Repeat the setup.

Each time you press the SEL/ RESET button, the setting speed increases or decreases by 5 km/h (mph). You can set the speed values over 5 km/h (5 mph) with 5 km/h (mph) steps. Always follow the posted speed limit and never drive faster than is safe for the traffic conditions.

To enter your selection, select the SET icon by pressing the INFO button, then press and hold the SEL/ RESET button.

CONTINUED

Instruments and Controls 135

06/09/13 17:11:36 32SWA600_141

Multi-Information Display

Toselectthealarmspeedwhiledriving:

INFO button, the selected icon is changed between the setting speeds and the exit icon.

To exit the customizing mode, select the exit mode shown above by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.

136

Instruments and Controls

Press the INFO button for about 1
second to switch the display. You will see the speed alarm settings on the multi-information display.

According to the selected display, you can select the alarm speed between the two setting speeds: 50 km/h and 80 km/h in the left- hand drive type, or 30 mph and 50
mph in the right-hand drive type. Each time you press and release the

Alarm off

Alarm on

Select the desired setting speed, then press the SEL/RESET button. Each time you press the SEL/ RESET button, the selected speed icon switches between on and off.

06/09/13 17:11:41 32SWA600_142

After your selection, press and release the INFO button to move to the exit mode. Press the SEL/ RESET button to enter your setting. If you press the INFO button, the display goes back to the setting mode. Repeat the setup.

Alarm on

Multi-Information Display

After pressing the SEL/RESET button, the display shows your setting for a few seconds, then goes back to the normal display.

If you do not press any button, the display returns to the normal display after about 10 seconds.

Instruments and Controls 137

06/09/13 17:11:47 32SWA600_143

Multi-Information Display

Change Setting You can customize some of the vehicle control settings to your preference. On vehicles with adaptive cruise control (ACC) system, the change setting consists of the two main items; ACC Setup and Meter Setup, and each main item has some custom settings. On the other vehicles, the change setting consists of all items in the meter setup menu. The following items are the settings you can customize.

138

Instruments and Controls

Go to the ACC Setup Customize Setting Display ＊ (see page 140).

Go to the Meter Setup Customize Setting Display (see page 144).

＊

: ACC Setup is available on vehicles with adaptive cruise control.

Multi-Information Display

06/09/13 17:11:52 32SWA600_144

Press and hold the INFO button to enter the customizing mode, then press and release the INFO button repeatedly to select ‘‘CHG SETTING.’’ While the multi-information display is showing ‘‘CHG SETTING,’’ press the SEL/RESET button. The display changes to the setting mode.

Press and release the INFO button repeatedly until you see the setup you want to customize, and press the SEL/RESET button to enter your selection. Each time you press the INFO button, the display changes as shown. To customize each setting, follow the procedures described on the following pages.

To exit the customizing mode after your selection, select the exit mode shown above by pressing the INFO button repeatedly, then press the SEL/RESET button. The display will return to the normal display.

Instruments and Controls 139

06/09/13 17:11:59 32SWA600_145

Multi-Information Display

AdaptiveCruiseControl(ACC)Setup You can customize either of the adaptive cruise control (ACC) system settings to your preference. Here are the settings you can customize.

ACCSetup

PRE-RUNNING CAR DETECT BEEP: You can turn on or off the alarm when the system detects a vehicle ahead of you (see page 141

).

ACC DISPLAY SPEED UNIT: Measurements in the ACC display can be selected; km or miles (see page

142

).

: Press the INFO button.

: Press the SEL/RESET button.

140

Instruments and Controls

06/09/13 17:12:06 32SWA600_146

Pre-RunningCarDetectBeep

Multi-Information Display

Onvehicleswithadaptivecruisecontrol (ACC) With this setting on, a beep sounds when the system detects a vehicle ahead of you. You will also hear a beep when the vehicle goes out of the range of your vehicle’s radar sensor. While the multi-information display is showing ‘‘PRE-RUNNING CAR DETECT BEEP,’’ press the SEL/RESET button. The display changes to the setting display.

You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.

When your selection is successfully completed, the display shows ‘‘SETUP ON’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode.

CONTINUED

Instruments and Controls

141

06/09/13 17:12:15 32SWA600_147

Multi-Information Display

AdaptiveCruiseControl(ACC) DisplaySpeedUnit

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the ‘‘PRE-RUNNING CAR DETECT BEEP’’ display.

To return to the normal display, select the the SEL/RESET button.

display, then press

Onvehicleswithadaptivecruisecontrol (ACC) The speed unit measurements of the adaptive cruise control can be selected; km/h or mph.

While the multi-information display is showing ‘‘ACC DISPLAY SPEED UNIT,’’ press the SEL/RESET button. The display changes to the setting display.

142

Instruments and Controls

06/09/13 17:12:21 32SWA600_148

You can select ‘‘km/h’’ or ‘‘mph’’. The highlighted item is the current setting. Each time you press the INFO button, the selected item changes. Enter your selection by pressing the SEL/RESET button.

When your selection is successfully completed, the display shows ‘‘SETUP km/h’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode.

Multi-Information Display

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

To exit this mode without changing the current setting, select and press the SEL/RESET button.

Instruments and Controls 143

06/09/19 17:13:29 32SWA600_149

Multi-Information Display

MeterSetup You can customize some of the vehicle control settings to suit your needs. The following items are the settings you can customize.

WARNING MESSAGE: The warning message is displayed with the symbol or not (see page ).

145

ADJUST OUTSIDE TEMP. DISPLAY: The outside temperature indicator value is adjustable up to page

＋ −

146

or

).

3°C (see

PRIMARY DISP SELECTION: A trip computer item displayed in the upper segment can be selected (see page

148

).

144

Instruments and Controls

: Press the INFO button. : Press the SEL/RESET button.

TRIP A RESET WITH REFUEL: Average fuel mileage for trip meter A can be reset after refueling (see page ).

150

ELAPSED TIME RESET: The elapsed time can be reset when you turn the ignition switch to the OFF (0) position or when you reset the trip meter A or B (see page

151

).

06/09/13 17:12:37 32SWA600_150

WarningMessage

Multi-Information Display

You can see message(s) with the system warning symbol on the multi- information display. While the multi- information display is showing ‘‘WARNING MESSAGE,’’ press the SEL/RESET button. The display changes to the setting display.

You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.

When your selection is successfully completed, the display shows ‘‘SETUP ON’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode.

CONTINUED

Instruments and Controls

145

To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button (see page 139
The display goes back to the ‘‘WARNING MESSAGE’’ display.

).

To return to the normal display, select the the SEL/RESET button.

display, then press

OutsideTemperatureDisplay Adjustment If you find that the temperature reading is always a few degrees below or above the actual temperature, adjust it as described on the following columns.

06/09/13 17:12:44 32SWA600_151

Multi-Information Display

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

146

Instruments and Controls

06/09/13 17:12:51 32SWA600_152

Multi-Information Display

While the multi-information display is showing ‘‘ADJUST OUTSIDE TEMP. DISPLAY,’’ press the SEL/ RESET button. The display changes to the setting display.

or

＋ −

The highlighted number is the current adjustment above or below the outside temperature. Select either icon by pressing the INFO button repeatedly then press the SEL/RESET button to change the setting value. You can select the 3, and 0, value between 0, 3. To enter your selection, − − − select the SET icon by pressing the INFO button, then press the SEL/ RESET button.

＋ ＋ ＋

1,

2,

1,

2,

±

°C’’ for a few seconds,

When your selection is successfully completed, the display shows ‘‘SETUP then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode.

CONTINUED

Instruments and Controls 147

06/09/13 17:13:02 32SWA600_153

Multi-Information Display

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.

148

Instruments and Controls

PrimaryDispSelection You can select a trip computer item displayed in the upper segment. The trip computer consists of the current fuel mileage, the average fuel economy, the estimated distance, the elapsed time, and the average speed. The upper segment always displays one of the trip computer items as a primary display when you turn the ignition switch to the ON (II) position. This selected item in the upper segment does not switch even if you press the INFO button. For more information of each trip computer items, see page 107

Here are the settings you can customize:

: Current fuel mileage

: Estimated distance

: Average fuel mileage

: Time travelled since you

last turned the ignition switch to the ON (II) position

: Average speed

06/09/13 17:13:09 32SWA600_154

Multi-Information Display

While the multi-information display is showing ‘‘PRIMARY DIPS SELECTION,’’ press the SEL/ RESET button. The display changes to the setting display.

You can select each trip computer symbol. Each time you press the INFO button, the selected symbol switches between them. Enter your selection by pressing the SEL/ RESET button.

When your selection is successfully completed, the display shows the appropriate symbol with a ‘‘SETUP’’ message for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.

CONTINUED

Instruments and Controls 149

06/09/13 17:13:16 32SWA600_155

Multi-Information Display

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

If you select SEL/RESET button, the normal display is shown again.

and press the

TripAResetWithRefuel

To cause the trip meter A and the average fuel mileage for trip A to reset every time you refuel your vehicle, adjust it as described as follows.

You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.

While the multi-information display is showing ‘‘TRIP A RESET WITH REFUEL,’’ press the SEL/RESET button. The display changes to the setting display.

150

Instruments and Controls

06/09/13 17:13:24 32SWA600_156

When your selection is successfully completed, the display shows ‘‘SETUP ON’’ or ‘‘SETUP OFF’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display will return to the normal display.

Multi-Information Display

ElapsedTimeReset

To cause the elapsed time to reset every time you turn the ignition switch to the LOCK (0) position or reset the trip meter A or B, adjust it as described as follows.

While the multi-information display is showing ‘‘ELAPSED TIME RESET,’’ press the SEL/RESET button. The display changes to the setting display.

CONTINUED

Instruments and Controls

151

06/09/13 17:13:31 32SWA600_157

Multi-Information Display

You can select ‘‘IGN OFF,’’ ‘‘TRIP A,’’ or ‘‘TRIP B’’. Each time you press the INFO button, the selected mode switches between them. Enter your selection by pressing the SEL/RESET button.

152

Instruments and Controls

IGN OFF: The elapsed time is reset when you turn the ignition switch to the LOCK (0) position.

TRIP A: The elapsed time is reset when you reset the trip meter A.

TRIP B: The elapsed time is reset when you reset the trip meter B.

IGN OFF is selected.

When your selection is successfully completed, the display shows the appropriate setting; ‘‘SETTING IGN OFF,’’ ‘‘SETUP TRIP A,’’ or ‘‘SETUP TRIP B’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.

06/09/13 17:13:35 32SWA600_158

If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.

Multi-Information Display

Instruments and Controls 153

06/09/13 17:13:42 32SWA600_159

Multi-Information Display

Selecting Language

Press and hold the INFO button to enter the customizing mode, then press and release the INFO button to select ‘‘LANGUAGE.’’ While the multi-information display is showing ‘‘LANGUAGE,’’ press the SEL/ RESET button. The display changes to the setting display.

You can select any of the following languages: English, French, German, Spanish, Italian, Portuguese. Press and release the INFO button to select the language, then press the SEL/RESET button to enter the selection.

When the language selection is successfully completed, the display changes to the screen shown above for a few seconds, then goes back to the ‘‘LANGUAGE’’ display. Press the INFO button repeatedly to select another customizing mode.

ENGLISH is selected.

154

Instruments and Controls

06/09/13 17:13:49 32SWA600_160

Multi-Information Display

Default Settings

If you fail to set the language setting, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.

To exit the customizing mode, select the exit mode shown above by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.

If you want to set the customizable vehicle control settings to the default setting, press the INFO button on the steering wheel repeatedly until ‘‘DEFAULT ALL’’ is displayed, then press the SEL/RESET button.

CONTINUED

Instruments and Controls 155

06/09/13 17:13:55 32SWA600_161

Multi-Information Display

To set the default settings, select ‘‘OK’’ by pressing the INFO button, then press and hold the SEL/RESET button for about 3 seconds to set.

After the DEFAULT ALL operation