2007 Honda CR V Owners Manual

Additional Information About Your Seat Belts

AnchoragePoints When replacing the seat belts, make certain to use the anchorage points shown in the illustrations.

(Rear Seat)

(Front Seat)

Not checking or maintaining seat belts can result in serious injury or death if the seat belts do not work properly when needed.

Check your seat belts regularly and have any problem corrected as soon as possible.

The rear seat has three lap/shoulder belts.

30

Driver and Passenger Safety

06/09/13 18:19:02 32SWA600_036

Additional Information About Your Airbags

Airbag System Components Your airbag system includes:

Automatic front seat belt tensioners (see page ). 27

Two SRS (supplemental restraint system) front airbags. The driver’s airbag is stored in the centre of the steering wheel; the front passenger’s airbag is stored in the dashboard. Both are marked ‘‘SRS AIRBAG’’ (see page

32

).

Two side airbags, one for the driver and one for a front passenger. The airbags are stored in the outer edges of the seat- backs. Both are marked ‘‘SIDE AIRBAG’’ (see page

34

).

Two side curtain airbags, one for each side of the vehicle. The airbags are stored in the ceiling above the side windows. The front and rear pillars on both sides are marked ‘‘SIDE CURTAIN ). AIRBAG’’ (see page

34

OnvehicleswithCMBS

Front seat belt e-pretensioners (see page

28

).

Sensors that can detect a moderate to severe front impact, side impact, or a rollover.

Sensors that can detect whether the driver’s seat belt and a front passenger’s seat belt is latched or unlatched (see page

19

).

A sophisticated electronic system that continually monitors and records information about the sensors, the control unit, the airbag activators, the seat belt tensioners, and driver and front passenger seat belt use when the ignition switch is in the ON (II) position.

An indicator on the instrument panel that alerts you to a possible problem with your airbags, sensors, or seat belt tensioners (see page

35

).

OnvehicleswithCMBS This indicator also alerts you to a possible problem with the seat belt e-pretensioners.

A rollover sensor that can detect if your vehicle is about to roll over and signal the control unit to deploy both side curtain airbags and front seat belt tensioners (see page

35

).

Emergency backup power in case your vehicle’s electrical system is disconnected in a crash.

Driver and Passenger Safety

31

06/09/13 18:19:09 32SWA600_037

Additional Information About Your Airbags

During a frontal crash, your seat belt restrains your lower body and torso, and the front airbag helps protect your head and chest.

Although both airbags normally inflate within a split second of each other, it is possible for only one airbag to deploy.

This can happen if the severity of a collision is at the margin, or threshold, that determines whether or not the airbags will deploy. In such cases, the seat belt will provide sufficient protection, and the supplemental protection offered by the airbag would be minimal.

How Your Front Airbags Work

If you ever have a moderate to severe frontal collision, sensors will detect the vehicle’s rapid deceleration.

If the rate of deceleration is high enough, the control unit will instantly inflate the driver’s and front passenger’s airbags, at the time and with the force needed.

32

Driver and Passenger Safety

After inflating, the front airbags immediately deflate, so they won’t interfere with the driver’s visibility, or the ability to steer or operate other controls.

06/09/13 18:19:17 32SWA600_038

The total time for inflation and deflation is one-tenth of a second, so fast that most occupants are not aware that the airbags deployed until they see them lying in their laps.

After a crash, you may see what looks like smoke. This is actually powder from the airbag’s surface. Although the powder is not harmful, people with respiratory problems may experience some temporary discomfort. If this occurs, get out of the vehicle as soon as it is safe to do so.

Additional Information About Your Airbags

Dual-StageAirbags Your front airbags are dual-stage airbags. This means they have two inflation stages that can be ignited sequentially or simultaneously, depending on crash severity.

moresevere

In a crash, both stages will ignite simultaneously to provide the quickest and greatest protection.

lesssevere

crash, one stage will

In a ignite first, then the second stage will ignite a split second later. This provides longer airbag inflation time with a little less force.

Dual-ThresholdAirbags Your front airbags are also dual- threshold airbags. Airbags with this feature have two deployment thresholds that depend on whether sensors detect the occupant is wearing a seat belt or not.

notlatched

If the occupant’s belt is the airbag will deploy at a slightly lower threshold, because the occupant would need extra protection.

latched

, the If the occupant’s belt is airbag will inflate at a slightly higher threshold, when the airbag would be needed to supplement the protection provided by the seat belt.

Driver and Passenger Safety

33

06/09/13 18:19:26 32SWA600_039

Additional Information About Your Airbags

How Your Side Airbags Work

How Your Side Curtain Airbags Work

SIDE CURTAIN AIRBAG

Only one airbag will deploy during a side impact. If the impact is on the passenger’s side, the passenger’s side airbag will deploy even if there is no passenger.

To get the best protection from the side airbags, front seat occupants should wear their seat belts and sit upright and well back in their seats.

If a front seat passenger leans sideways and his head is in the deployment path of the side airbag, he can be seriously injured by an inflating side airbag. An inflating side airbag can strike the child with enough force to kill or very seriously injure a child. For the information of the side airbags hazards, see pages 43

and

67

InaSideImpact In a moderate to severe side impact, sensors will detect rapid acceleration and signal the control unit to instantly inflate the side curtain airbag and activate the seat belt tensioner on the driver’s or the passenger’s side of the vehicle.

If you ever have a moderate to severe side impact, sensors will detect rapid acceleration and signal the control unit to instantly inflate either the driver’s or the passenger’s side airbag and activate the seat belt tensioner.

34

Driver and Passenger Safety

06/09/13 18:19:35 32SWA600_040

Additional Information About Your Airbags

If the impact is on the passenger’s side, the passenger’s side curtain airbag will inflate even if there are no occupants on that side of the vehicle.

To get the best protection from the side curtain airbags, occupants should wear their seat belts and sit upright and well back in their seats.

InaRollover If the rollover sensor detects your vehicle is about to roll over, it signals the control unit, which immediately deploys both side curtain airbags and activates both front seat belt tensioners.

The airbag on the passenger’s side will deploy, and the seat belt tensioner will activate, even if there are no passengers on that side of the vehicle.

How the SRS Indicator Works The SRS indicator alerts you to a potential problem with your airbags, sensors, or seat belt tensioners.

OnvehicleswithCMBS This indicator also alerts you to a possible problem with the seat belt e-pretensioners.

When you turn the ignition switch to the ON (II) position, this indicator comes on briefly then goes off. This tells you the system is working properly.

CONTINUED

Driver and Passenger Safety

35

06/09/13 18:19:42 32SWA600_041

Additional Information About Your Airbags

Onvehicleswithmulti-information display You will also see the symbol ‘‘ ‘‘CHECK SYSTEM’’ message on the multi-information display (see page 125

’’ or the symbol with a

).

If you see any of these indications, the airbags and seat belt tensioners may not work properly when you need them.

Ignoring the SRS indicator can result in serious injury or death if the airbag systems or tensioners do not work properly.

Have your vehicle checked by a dealer as soon as possible if the SRS indicator alerts you to a possible problem.

If the indicator comes on at any other time, or does not come on at all, you should have the system checked by your dealer. For example:

If the SRS indicator does not come on after you turn the ignition switch to the ON (II) position.

If the indicator stays on after the engine starts.

If the indicator comes on or flashes on and off while you drive.

36

Driver and Passenger Safety

06/09/13 18:19:50 32SWA600_042

Airbag Service Your airbag systems and automatic seat belt tensioners are virtually maintenance free, and there are no parts you can safely service. However, you must have your vehicle serviced if:

Any airbag

Anairbageverinflates. that has deployed must be replaced along with the control unit and other related parts. Any seat belt tensioner that activates must also be replaced.

Do not try to remove or replace any airbag by yourself. This must be done by your dealer or a knowledgeable body shop.

TheSRSindicatoralertsyoutoa Take your vehicle to an problem. authorized dealer as soon as possible. If you ignore this indication, your airbags may not operate properly.

Additional Information About Your Airbags

Handling is allowed by trained personnel only. It is prohibited to remove the airbag unit/belt- tensioner from the vehicle. In case of malfunction, shutdown or after airbag inflation/belt-tensioner operation you have to ask a qualified shop for repair or removal.

Additional Safety Precautions

Donotattempttodeactivateyour airbags. seat belts provide the best protection.

Together, airbags and

Donottamperwithairbagand automaticseatbelttensioner componentsorwiringforany Tampering could cause reason. the airbags and automatic seat belt tensioners to deploy, possibly causing very serious injury.

CONTINUED

Driver and Passenger Safety

37

06/09/13 18:19:54 32SWA600_043

Additional Information About Your Airbags

Donotexposethefrontseat-backs If water or another liquid toliquid. soaks into the seat-back, it can prevent the side airbag system from working properly.

Donotcoverorreplacefrontseat- backcoverswithoutconsulting Improperly replacing yourdealer. or covering front seat-back covers can prevent your side airbags from inflating during a side impact.

38

Driver and Passenger Safety

06/09/13 18:20:03 32SWA600_044

Protecting Children General Guidelines

−

All Children Must Be Restrained Each year, many children are injured or killed in vehicle crashes because they are either unrestrained or not properly restrained. In fact, vehicle accidents are the number one cause of the death of children ages 12 and under.

To reduce the number of child deaths and injuries, infants and children should be properly restrained when they ride in a vehicle.

Infantsandsmallchildrenmustbe restrainedinanapprovedchild restraintsystemthatisproperly (see pages securedtothevehicle 39

65

).

−

Children who are unrestrained or improperly restrained can be seriously injured or killed in a crash.

Any child too small for a seat belt should be properly restrained in an approved child restraint system. A larger child should be properly restrained with a seat belt and use a booster seat if necessary.

Largerchildrenmustberestrained withalap/shoulderbeltandrideon aboosterseatuntiltheseatbeltfits ). themproperly

(see pages

67

71

−

CONTINUED

Driver and Passenger Safety

39

Children depend on adults to protect them. However, despite their best intentions, many adults do not know how to passengers.

protect child

properly

If you have children, or ever need to drive with a child in your vehicle, be sure to read this section. It begins with important general guidelines, then presents special information for infants, small children, and larger children.

06/09/13 18:20:10 32SWA600_045

Protecting Children General Guidelines

−

In most countries, child restraint systems must meet the specifications of the ECE 44
regulation.

In many countries, the law requires children younger than 12 years of age and less than 150 cm (60 in) in height to be secured in an officially approved and suitable child restraint system. In those countries, officially approved and suitable child restraint systems must therefore be used in order to transport a child on any passenger seat whatsoever. Please check your local legal requirements.

All Children Should Sit in a Back Seat According to crash statistics, children of all ages and sizes are safer when they are restrained in a back seat. It is recommended that all children age 12 and under be properly restrained in a back seat.

Children who ride in back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating airbag when they ride in the back.

The Passenger’s Front Airbag Poses Serious Risks Front airbags have been designed to help protect adults in a moderate to severe frontal collision. To do this, the passenger’s front airbag is quite large, and it can inflate with enough force to cause very serious injuries.

Infants Neverputarearwardfacingchild restraintsysteminthefrontseatofa vehicleequippedwithapassenger’s If the airbag inflates, it frontairbag. can hit the back of the child restraint system with enough force to kill or very seriously injure an infant.

40

Driver and Passenger Safety

06/09/13 18:20:19 32SWA600_046

As required by E.C.E Regulation No. 94;

DO NOT place rear-facing child seat on this seat with airbag.

DEATH OR SERIOUS INJURY can occur.

Protecting Children General Guidelines

−

If the passenger’s front airbag inflates, it can hit the rearward facing child restraint system with great force. The rearward facing child restraint system can be dislodged or struck with enough force to cause very serious injury to the infant.

Small Children Placingafrontfacingchildrestraint systeminthefrontseatofavehicle equippedwithapassenger’sfront airbagcanbehazardous. vehicle seat is too far forward, or the child’s head is thrown forward during a collision, an inflating front airbag can strike the child with enough force to kill or very seriously injure a small child.

If the

Larger Children Childrenwhohaveoutgrownchild restraintsystemsarealsoatriskof beinginjuredorkilledbyaninflating Whenever passenger’sfrontairbag. possible, larger children should sit in the back seat, in a booster seat if needed, and be properly restrained with a seat belt (see page 67
important information about protecting larger children).

for

In all cases observe the legal requirements of the countries in which you will drive.

CONTINUED

Driver and Passenger Safety

41

06/09/13 18:20:24 32SWA600_047

Protecting Children General Guidelines

−

To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the windscreen, on the front passenger’s doorjamb and on the front passenger’s sun visor. Please read and follow the instructions on these labels.

As required by E.C.E Regulation No. 94;

Extreme Hazard!

DO NOT use a rearward facing child restraint on a seat protected by an airbag in front of it!

DO NOT place rear-facing child seat on this seat with airbag.

DEATH OR SERIOUS INJURY can occur.

42

Driver and Passenger Safety

06/09/19 17:13:21 32SWA600_048

Protecting Children General Guidelines

−

The Side Airbag Poses Serious Risks Side airbags have been designed to help protect adults in a moderate to severe side impact. If any part of a child’s body is in the path of a deploying airbag, an inflating side airbag can strike the child with enough force to kill or very seriously injure a child.

To remind you of the side airbags hazards, and that children must be properly restrained in the back seat, your vehicle has the safety label on each front doorjamb.

Leaning over the front door can result in serious injury or death if the side airbag inflates.

Always sit upright with their back against the seat-back.

Driver and Passenger Safety

43

06/09/13 18:20:39 32SWA600_049

Protecting Children General Guidelines

−

If a Child Requires Close Attention Many parents say they prefer to put an infant or a small child in the front passenger seat so they can watch the child, or because the child requires attention.

Placing a child in the front seat exposes the child to hazards in a frontal collision or a side impact, and paying close attention to a child distracts the driver from the important tasks of driving, placing both of you at risk.

If a child requires close physical attention or frequent visual contact, we strongly recommend that another adult ride with the child in the back seat. The back seat is far safer for a child than the front.

Additional Safety Precautions

Neverholdaninfantorchildon If you are not wearing a yourlap. seat belt in crash, you could be thrown forward and crush the child against the dashboard or a seat-back. If you are wearing a seat belt, the child can be torn from your arms and be seriously hurt or killed.

Neverputaseatbeltoveryourself andachild. belt could press deep into the child and cause serious or fatal injuries.

During a crash, the

Neverlettwochildrenusethe If they do, they sameseatbelt. could be very seriously injured in a crash.

If You Must Drive with Several Children Your vehicle has a back seat where children can be properly restrained. If you ever have to carry a group of children, and a child must ride in front:

Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page

67

).

Move the vehicle seat as far to the rear as possible (see page

189

).

Have the child sit upright and well back in the seat (see page

21

).

Make sure the seat belt is properly positioned and secured (see page 19

).

44

Driver and Passenger Safety

06/09/13 18:20:48 32SWA600_050

Makesureanyunusedseatbelt thatachildcanreachisbuckled, thelockableretractorisactivated, andthebeltisfullyretractedand locked. seat belt around their neck, they can be seriously or fatally injured. (See pages activate and deactivate the lockable retractor.)

If a child wraps a loose

for how to

and

59

62

Usethechildproofdoorlocksto preventchildrenfromopeningthe reardoors. children from accidentally falling out (see page

This can prevent

181

).

WARNING: Usethemainpower windowswitchtopreventchildren fromopeningthewindows.Usingthis featurewillpreventchildrenfrom playingwiththewindows,which couldexposethemtohazardsor 208
distractthedriver(seepage ).

Protecting Children General Guidelines

−

Even very young

Keepvehiclekeys/remote transmittersoutofthereachof children. children learn how to unlock vehicle doors, turn on the ignition switch, and open the tailgate, which can lead to accidental injury or death.

‘‘Never let children kneel on seats or stand while the vehicle is in motion. The violent forces created during emergency braking will cause the children to be thrown forward. The children could be seriously injured or killed.’’

WARNING: Alwaystaketheignition keywithyouwheneveryouleavethe vehiclealone(withotheroccupants).

Donotleavechildrenaloneina Leaving children without vehicle. adult supervision is illegal in some countries, and can be very hazardous.

For example, infants and small children left in a vehicle on a hot day can die from heatstroke. A child left alone with the key in the ignition switch can accidentally set the vehicle in motion, possibly injuring themselves or others.

Lockalldoorsandthetailgate whenyourvehicleisnotinuse. Children who play in vehicles can accidentally get trapped inside. Teach your children not to play in or around vehicles.

Driver and Passenger Safety

45

06/09/13 18:20:58 32SWA600_051

Protecting Infants and Small Children

Only a rearward facing child restraint system provides proper support for a baby’s head, neck and back.

Two types of restraints may be used: a restraint system designed exclusively for infants, or a convertible restraint system used in the rearward facing, reclining mode.

For EU countries, refer to page for the recommended child 52
restraint system.

Donotputarearwardfacingchild restraintsysteminaforward-facing If placed facing forward, an position. infant could be very seriously injured during a frontal collision.

Protecting Infants

ChildRestraintSystemType An infant must be properly restrained in a rear-facing, reclining child restraint system until the child reaches the restraint system maker’s weight or height limit for the restraint system, and the child is at least one year old.

46

Driver and Passenger Safety

RearwardFacingChildRestraint SystemPlacement A rearward facing child restraint system can be placed in any seating position in the back seat, but not in the front. facingchildrestraintsysteminthe frontseat.

Neverputarearward

For EU countries, an approved rearward facing child restraint system should be placed in any seating position in the back seat (see page

52

).

If the passenger’s front airbag inflates, it can hit the back of the restraint with enough force to kill or seriously injure an infant.

06/09/13 18:21:04 32SWA600_052

When properly installed, a rearward facing child restraint system may prevent the driver or a front passenger from moving their seat as far back as recommended, or from locking their seat-back in the desired position.

In either situation, we strongly recommend that you install the child restraint system directly behind the front passenger seat, move the seat as far forward as needed, and leave it unoccupied. Or you may wish to get a smaller rearward facing child restraint system.

Protecting Infants and Small Children

As required by E.C.E Regulation No. 94;

Placing a rearward facing child restraint system in the front seat can result in serious injury or death if the passenger’s front airbag inflates.

Always place a rearward facing child restraint system in the back seat, not the front.

DO NOT place rear-facing child seat on this seat with airbag.

DEATH OR SERIOUS INJURY can occur.

If the passenger’s front airbag inflates, it can hit the rearward facing child restraint system with great force. The rearward facing child restraint system can be dislodged or struck with enough force to cause very serious injury to the infant.

Driver and Passenger Safety

47

06/09/13 18:21:13 32SWA600_053

Protecting Infants and Small Children

Protecting Small Children

ChildRestraintSystemType A child who is at least one year old, and who fits within the child restraint system maker’s weight and height limits, should be restrained in a front facing, upright child restraint system.

Of the different restraint systems available, we recommend those that have a five-point harness system as shown.

48

Driver and Passenger Safety

We also recommend that a small child uses the child restraint system as long as possible, until the child reaches the weight or height limit for the restraint system.

For EU countries, refer to page for the recommended child 52
restraint system.

ChildRestraintSystemPlacement We strongly recommend placing a front facing child restraint system in a back seat, not the front.

Placingafrontfacingchildrestraint systeminthefrontseatofavehicle equippedwithapassenger’sairbag If the vehicle seat canbehazardous. is too far forward, or the child’s head is thrown forward during a collision, an inflating airbag can strike the child with enough force to cause very serious or fatal injuries.

If it is necessary to put a front facing child restraint system in the front, move the vehicle seat as far to the rear as possible, and be sure the child restraint system is firmly secured to the vehicle and the child is properly strapped in the restraint system.

Placing a front facing child restraint system in the front seat can result in serious injury or death if the front airbag inflates.

If you must place a front facing child restraint system in front, move the vehicle seat as far back as possible, and properly restrain the child.

06/09/13 18:21:22 32SWA600_054

When buying a child restraint system, you need to choose either a conventional child restraint system, or one designed for use with the lower anchorages and tethers.

Conventional child restraint systems must be secured to a vehicle with a seat belt, whereas lower anchorages system-compatible child restraint systems are secured by attaching the restraint to hardware built into each rear seating position in the back seat.

Since lower anchorages system- compatible child restraint systems are easier to install and reduce the possibility of improper installation, we recommend selecting this style.

Selecting a Child Restraint System

We also recommend selecting a lower anchorages system-compatible child restraint system with a rigid, rather than a flexible, anchor (see page

54

).

In EU countries, a child restraint system with a flexible anchor is not available.

In seating positions and vehicles not equipped with lower anchorages system, a lower anchorages system- compatible child restraint system can be installed using a seat belt.

Whatever type of child restraint you choose, to provide proper protection, a child restraint system should meet three requirements:

1.

In most

Thechildrestraintsystemshould meetsafetystandards. countries, child restraint systems must meet the specifications of the ECE 44 regulation. Look for the approval mark on the system and the manufacturer’s statement of compliance on the box.

The manufacturer of the vehicle does not assume any responsibility for damage which would be caused by a defect inherent in the recommended child restraint system.

CONTINUED

Driver and Passenger Safety

49

06/09/13 18:21:27 32SWA600_055

Selecting a Child Restraint System

2.

Thechildrestraintsystemshould beofthepropertypeandsizetofit thechild. Rearward facing for infants, front facing for small children.

Make sure the restraint system fits your child. Check the manufacturer’s instructions and labels for height and weight limits.

3.

Thechildrestraintsystemshould fitthevehicleseatingposition(or positions)whereitwillbeused.

Before purchasing a conventional child restraint system, or using a previously purchased one, we recommend that you test the restraint system in the specific vehicle seating position or positions where the child restraint system will be used.

For EU countries, refer to page 52
for the recommended child restraint system.

50

Driver and Passenger Safety

06/09/13 18:21:36 32SWA600_056

After selecting a proper child restraint system and a good place to install the restraint system, there are three main steps in installing the restraint system:

1.

All child

Properlysecurethechildrestraint systemtothevehicle. restraint systems must be secured to the vehicle with the lap part of a lap/shoulder belt or with the lower anchorages system. A child whose restraint system is not properly secured to the vehicle can be endangered in a crash.

ExceptforEuropeanmodels If you use a lap/shoulder belt without a lockable retractor, be sure you install a locking clip on the seat belt (see page

63

).

Installing a Child Restraint System

2.

Makesurethechildrestraint After systemisfirmlysecured. installing a child restraint system, push and pull the restraint system forward and from side-to-side to verify that it is secure.

A child restraint system secured with a seat belt should be installed as firmly as possible. However, it does not need to be ‘‘rock solid.’’ Some side-to-side movement can be expected and should not reduce the child restraint system’s effectiveness.

If the child restraint system is not secure, try installing it in a different seating position, or use a different style of child restraint system that can be firmly secured.

For EU countries, refer to page for the recommended child 52
restraint system.

3.

Securethechildinthechild Make sure the restraintsystem. child is properly strapped in the child restraint system according to the child restraint system maker’s instructions. A child who is not properly secured in a child restraint system can be seriously injured in a crash.

The following pages provide the recommended child restraint systems for EU countries and guidelines on how to properly install a child restraint system. A front facing child restraint system is used in all examples, but the instructions are the same for a rearward facing child restraint system.

Driver and Passenger Safety

51

06/09/13 18:21:49 32SWA600_057

Installing a Child Restraint System

Child Restraint System for EU Countries Various types of child restraint systems are available. Not all types are suitable for your vehicle. Please refer to the table below to select which category of child restraint system can be used on each seating position.

Mass Group

Front passenger

group 0 Up to 10 kg group 0
Up to 13 kg

＋

group I 9 kg to 18 kg

Honda LORD

＊

group II 15 kg to 25 kg group III 22 kg to 36 kg

Honda KID Honda KID

＊

＊

Rear passenger

Seating Position

Outboard

＊

IL (Honda BABY-SAFE

ISO FIX) or U

＊

IUF (Size class A, B1, B)

＊

or U

＊

＊

Centre

Honda BABY-SAFE

IL (Honda BABY-SAFE ISO FIX) or Honda BABY-SAFE IUF (Size class A, B1, B) or

Honda LOAD Honda KID Honda KID

IL: IUF:

U: X: ＊ ＊

1: 2:

Suitable for particular ISO FIX child restraint systems (CRS) given in this table. Suitable for front facing ISO FIX child restraint systems of universal category approved for use in this mass group. For group I, the front facing genuine Honda ISO FIX child restraint system is available from your dealer. Suitable for ‘‘universal’’ category child restraints approved for use in this mass group. Seat position not suitable for children in this mass group. Move the front seat to its rearmost position. Adjust the front seat forward to 30 mm (3 notches) from its rearmost position.

A size class is specified for some child restraint systems. Make sure to check the size class as indicated on the manufacturer’s instructions, package, and labels of the child restraint. The particular child restraints in the above table are Honda Genuine Parts. They are available from your dealer. For a correct installation, please refer to the Child Restraint Instruction Manual. 52

Driver and Passenger Safety

06/11/27 16:23:24 32SWA600_058

Installing a Child Restraint System

Your vehicle has the manual adjustable rear seat. To install a child restraint system in any seating position on the rear seat, slide the rear seat as far back as it can go.

The use of any child restraint system which is not suitable for your vehicles would not properly secure the infant or child who could therefore be killed or seriously injured.

Your vehicle is equipped with lower anchorages at each seating position on the rear seat. These anchorages are only to be used with a child restraint system designed to be attached to the lower anchorages. Refer to page for how to install a child restraint system to the lower anchorages.

54

Driver and Passenger Safety

53

06/09/13 18:22:03 32SWA600_059

Installing a Child Restraint System

Installing a Child Restraint System with the Lower Anchorages Your vehicle is equipped with lower anchorages at the rear seats to secure a child restraint system in any seating position: one in each outer seating position, or one in the centre.

The five lower anchorages are located between the seat-back and seat bottom, and are to be used only with a child restraint system designed for use with the lower anchorages.

The location of each lower anchorage is indicated by a small button above the anchorage point.

For EU countries, refer to page for the recommended child 52
restraint system.

When you install a child restraint system in the rear centre seating

54

Driver and Passenger Safety

BUTTON

LOWER ANCHORAGES for CENTRE POSITION

UsingtheOuterLowerAnchorages

LOWER ANCHORAGES for OUTER POSITION

position, use the centre lower anchorages as shown in the illustration. To install a child restraint system in either outer seating position, use the outer lower anchorages. You can install up to two child restraint systems at a time using the outer lower anchorages.

Do not attach two child restraint system connectors to a single lower anchorage at a time.

OUTER LOWER ANCHORAGES

To install a child restraint system designed to be attached to the lower anchorages in either of the rear outer seats:

1.

Store the seat belt buckle or tongue in the storage pockets.

06/09/13 18:22:12 32SWA600_060

2.

3.

Make sure there are no objects near the anchorages that could prevent a secure connection between the child restraint system and the anchorages.

Onsomechildrestraintsystems You may use optional guide-cups that came with your child restraint system to install it to the lower anchorages without damaging the seat surface.

Installing a Child Restraint System

LOWER ANCHORAGE

Rigid type

GUIDE-CUP

Attach the guide-cups to the lower anchorages as shown in the illustration.

When using the guide-cups, always follow the child restraint system manufacturer’s instructions.

4.

Place the child restraint system on the vehicle seat, then attach the child restraint system to the lower anchorages according to the child restraint system maker’s instructions.

Some child restraint systems designed for use with lower anchorages have a rigid-type connector as shown above.

CONTINUED

Driver and Passenger Safety

55

06/09/13 18:22:20 32SWA600_061

Installing a Child Restraint System

Flexible type

5.

Whatever type you have, follow the child restraint system maker’s instructions for adjusting or tightening the fit.

Flexible type child restraint system is available in some countries. In EU countries, this type is not available.

6.

Set the head restraint to its highest position.

Other child restraints have a flexible- type connector as shown above.

7.

Route the tether strap over the seat-back through the outsides of the head restraint legs, then attach the attaching clip to the tether anchor fitting in the ceiling as shown in the illustration. Make sure the strap is not twisted, then tighten the strap according to the child restraint system maker’s instructions.

56

Driver and Passenger Safety

ATTACHING CLIP

TETHER ANCHOR FITTING

The above illustration shows how the attaching clip should be routed in EU countries.

06/09/13 18:22:28 32SWA600_062

Installing a Child Restraint System

ATTACHING CLIP

8.

Push and pull the child restraint system forward and from side-to- side to verify that it is secure.

UsingtheCentreLowerAnchorages

TETHER ANCHOR FITTING

TETHER ANCHOR FITTING

On some child restraint types, route the tether strap between the legs of the head restraint as shown.

COVER

CENTRE LOWER ANCHORAGES To install a child restraint system in the rear centre seating position, use the centre lower anchorages as shown above.

1.

Follow step 1 through 5 as described previously to secure the child restraint system.

CONTINUED

Driver and Passenger Safety

57

06/09/13 18:22:36 32SWA600_063

Installing a Child Restraint System

2.

Lower the head restraint to its lowest position.

3.

Pull down the cover to access the tether anchor fitting.

TETHER ANCHOR

TETHER ANCHOR FITTING

The design and suitability of the child restraint systems must be carefully checked with the child restraint system manufacturer concerned and the seller of those systems. If you are not sure, consult your dealer before purchasing this type of child restraint system.

ATTACHING CLIP

On some child restraint system, route the tether strap over the head restraint as shown.

5.

Push and pull the child restraint system forward and from side-to- side to verify that it is secure.

4.

ATTACHING CLIP Route the tether strap over the seat-back, then attach the attaching clip to the tether anchor fitting in the centre of the ceiling, making sure the strap is not twisted. Tighten the strap according to the child restraint system maker’s instructions.

58

Driver and Passenger Safety

06/09/13 18:22:45 32SWA600_064

Installing a Child Restraint System

Installing a Child Restraint System with a Lap/Shoulder Belt When not using the lower anchorages system, all child restraint systems must be secured to the vehicle with the lap part of a lap/ shoulder belt.

In addition, the lap/shoulder belts in the back seating positions have a lockable retractor that must be activated to secure a child restraint system.

If you intend to install a child restraint system in the centre seating position of the rear seat, make sure the detachable seat belt anchor is securely latched (see page 199

).

To properly route a lap/shoulder belt through a child restraint system, follow the restraint system maker’s instructions.

For EU countries, refer to page for installing a child restraint 52
system.

The procedures in the following pages are described based on a front facing child restraint system available in EU countries.

1.

Place the child restraint system in the desired back seating position. Make sure the child restraint is positioned well back in the seat- back.

If you place the child restraint system in any rear seating position and use the tether strap for additional security, make sure to set the head restraint properly and attach the attaching clip to the anchor fitting before securing the child restraint system with the lap/ shoulder belt.

2.

Route the belt through the restraint according to the restraint system maker’s instructions, then insert the latch plate into the buckle.

CONTINUED

Driver and Passenger Safety

59

06/09/13 18:22:52 32SWA600_065

Installing a Child Restraint System

3.

To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops.

4.

5.

Push down the tab. Route the shoulder part of the belt into the slit at the side of the restraint, then let the belt feed back into the retractor.

After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked, and you will need to repeat these steps.

6.

After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child restraint system will not be secure.

60

Driver and Passenger Safety

06/09/13 18:22:58 32SWA600_066

To remove slack, it may help to put weight on the child restraint system, or push on the back of the restraint system while pulling up on the belt.

Installing a Child Restraint System

7.

Secure the belt in the slit by pushing up the tab. Make sure the belt is not twisted and it is positioned properly in the slit.

8.

Push and pull the child restraint system forward and from side-to- side to verify that it is secure enough to stay upright during normal driving manoeuvres. If the child restraint system is not secure, unlatch the belt, allow it to retract fully, then repeat these steps.

CONTINUED

Driver and Passenger Safety

61

06/09/13 18:23:04 32SWA600_067

Installing a Child Restraint System

To deactivate the lockable retractor and remove a child restraint system, unlatch the buckle, unroute the seat belt, and let the belt fully retract.

LOCKING CLIP

ExceptforEuropeanmodels Onvehicleswithoutlockableretractor fittedtotheseatwherethechildis positioned When you secure a child restraint system with a lap/shoulder belt, be sure you install a locking clip on the seat belt (see page

63

).

62

Driver and Passenger Safety

06/09/13 18:23:14 32SWA600_068

UsingaSeatBeltLockingClip ExceptforEuropeanmodels Onvehicleswithoutlockableretractor fittedtotheseatwherethechildis positioned Always use a seat belt locking clip when you secure a child restraint system to your vehicle with a lap/ shoulder belt. This helps prevent the restraint system from shifting position or overturning.

A locking clip is usually included with the child restraint system. If you need a clip, contact the seat’s manufacturer or a store that sells child restraints.

If it is necessary to put a front facing child restraint system in the front, move the vehicle seat as far to the rear as possible, be sure the child restraint system is firmly secured to the vehicle, and the child is properly strapped in the restraint system (see page

48

).

Installing a Child Restraint System

To install a locking clip, do the following:

1.

2.

3.

Place the child restraint in the seat with a lap/shoulder belt. Route the lap/shoulder belt through the restraint according to the seat manufacturer’s instructions.

Insert the latch plate into the buckle. Pull on the shoulder part of the belt to make sure there is no slack in the lap portion.

Tightly grasp the belt near the latch plate. Pinch both parts of the belt together so they won’t slip through the latch plate. Unbuckle the seat belt.

LOCKING CLIP

4.

5.

Install the locking clip as shown. Position the clip as close as possible to the latch plate.

Insert the latch plate into the buckle. Push and pull on the child restraint system to verify that it is held firmly in place. If it is not, repeat these steps until the restraint is secure.

Driver and Passenger Safety

63

06/09/13 18:23:23 32SWA600_069

Installing a Child Restraint System

Installing a Child Restraint System with a Tether Children riding in vehicles should be restrained to minimize the risk of injury in the event of an accident.

TETHER ANCHOR POINTS

Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. (The owners may check with the child restraint system maker to determine whether a tether is available for a particular child restraint system.)

UsinganOuterAnchorFitting

ATTACHING CLIP

TETHER STRAP

ANCHOR FITTING

1.

After properly securing the child restraint system (see page or ), route the tether strap over 59
the seat-back and on both sides of the head restraint as shown.

54

The above illustration shows how the tether strap should be routed in EU countries.

A child restraint system with a tether can be installed in any seating position in the back seat, using one of the anchor points shown in the illustration.

64

Driver and Passenger Safety

06/09/13 18:23:32 32SWA600_070

Installing a Child Restraint System

ATTACHING CLIP

2.

3.

Attach the attaching clip to the anchor fitting, making sure the strap is not twisted.

Tighten the tether strap according to the child restraint system maker’s instructions.

UsingtheCentreAnchor

TETHER ANCHOR FITTING

ANCHOR FITTING

On some child restraint types, route the tether strap between the legs of the head restraint as shown.

COVER

1.

Push down the rear centre head restraint to the lowest position.

2.

After properly securing the child restraint system (see page ), open the anchor cover.

59

CONTINUED

Driver and Passenger Safety

65

06/09/13 18:23:39 32SWA600_071

Installing a Child Restraint System

TETHER ANCHOR FITTING

TETHER ANCHOR FITTING

ATTACHING CLIP

3.

Route the tether strap over the head restraint, then attach the attaching clip to the anchor fitting, making sure the tether strap is not twisted.

ATTACHING CLIP On some child restraint system, route the tether strap over the head restraint as shown.

4.

Tighten the tether strap according to the child restraint system maker’s instructions.

66

Driver and Passenger Safety

To attach the tether to the child restraint system, follow the child restraint system maker’s instructions.

When the child restraint system is used, follow the instructions that came with the child restraint system.

Childrestraintanchorages

WARNING: aredesignedtowithstandonlythose loadsimposedbycorrectlyfittedchild restraints.Undernocircumstancesare theytobeusedforadultseatbelts, harnessesorforattachingotheritems orequipmenttothevehicle.

06/09/13 18:23:44 32SWA600_072

When a child reaches the recommended weight or height limit for a front facing child restraint system, the child should sit in a back seat on a booster seat and wear a lap/shoulder belt.

The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in front.

Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.

If a child must ride in front, move the vehicle seat as far back as possible, use a booster seat if needed, have the child sit up properly and wear the seat belt properly.

Protecting Larger Children

Leaning over the front door can result in serious injury or death if the side airbag inflates.

Always sit upright with their back against the seat-back.

Driver and Passenger Safety

67

06/09/13 18:23:55 32SWA600_073

Protecting Larger Children

Checking Seat Belt Fit

To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt, then ask yourself:

1.

Does the child sit all the way back against the seat?

2.

Do the child’s knees bend comfortably over the edge of the seat?

68

Driver and Passenger Safety

3.

Does the shoulder belt cross between the child’s neck and arm?

4.

Is the lap part of the belt as low as possible, touching the child’s thighs?

5.

Will the child be able to stay seated like this for the whole trip?

If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat.

Using a Booster Seat

A child who has outgrown a front facing child restraint system should ride in a back seat and use a booster seat until the lap/shoulder belt fits them properly without the booster.

06/09/13 18:24:02 32SWA600_074

Protecting Larger Children

Booster seats can be high-back or low-back. Whichever style you select, make sure the booster seat meets approved safety standards (see page ) and that you follow the booster 49
seat maker’s instructions.

If a child who uses a booster seat must ride in front, move the vehicle seat as far back as possible and be sure the child is wearing the seat belt properly.

A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster seat.

For EU countries, refer to page 52

for the booster seat placement.

GUIDE

A back-rest may be available for a specific booster seat. Install the back-rest to the booster seat and adjust it to the vehicle seat according to the booster seat maker’s instructions. Make sure the seat belt is properly routed through the guide at the shoulder of the back-rest and the belt does not touch and cross the child’s neck (see page

19

).

Driver and Passenger Safety

69

06/09/13 18:24:14 32SWA600_075

Protecting Larger Children

When Can a Larger Child Sit in Front It is recommended that all children age 12 and under be properly restrained in the back seat.

Of course, children vary widely. And while age may be one indicator of when a child can safely ride in front, there are other important factors you should consider.

PhysicalSize Physically, a child must be large enough for the lap/shoulder belt to properly fit (see pages ). If 67
the seat belt does not fit properly, with or without the child sitting on a booster seat, the child should not sit in front.

and

19

Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly, and wearing the seat belt properly throughout a ride.

The back seat is the safest place for a child of any age or size.

If the passenger’s front airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position.

A side airbag also poses risks. If any part of a larger child’s body is in the path of a deploying side airbag, the child could receive possibly serious injuries.

70

Driver and Passenger Safety

If you decide that a child can safely ride up front, be sure to:

Carefully read the owner’s manual, and make sure you understand all seat belt instructions and all safety information.

Move the vehicle seat to the rear- most position.

Have the child sit up straight, back against the seat, and feet on or near the floor.

Check that the child’s seat belt is properly and securely positioned.

Remind the child not to lean toward the door.

Supervise the child. Even a mature child sometimes needs to be reminded to fasten the seat belt or sit properly.

Protecting Larger Children

Devices intended to

Donotputanyaccessoriesona seatbelt. improve a child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective and increase the chance of serious injury in a crash.

06/09/13 18:24:20 32SWA600_076

Additional Safety Precautions

Donotletachildwearaseatbelt This could result acrosstheneck. in serious neck injuries during a crash.

This could

Donotletachildputtheshoulder partofaseatbeltbehindtheback orunderthearm. cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.