2004 Honda Civic Hybrid Owners Manual

Pour coolant into the reserve tank. Fill it to halfway between the MAX and MIN marks. Put the cap back on the reserve tank.

Do not add any rust inhibitors or other additives to your vehicle’s cooling system. They may not be compatible with the coolant or engine components.

Main MenustTable of Contents０３／０７／１７　０９：１０：４５　３１Ｓ５Ｂ６２０　０１６０　

Windshield Washers

NOTICE: Do not use engine antif reeze or a vinegar/water solution in the windshield washer reservoir. Antif reeze can damage your vehicle’s paint, while a vinegar/water solution can damage the windshield washer pump. Use only commercially-available windshield washer f luid.

Check the fluid level in the windshield washer reservoir at least monthly during normal use. OnCanadianmodels: level indicator will light when the level is low.

The low washer

Fill the reservoir with a good-quality windshield washer fluid. This increases the cleaning capability and prevents freezing in cold weather. When you refill the reservoir, clean the edges of the windshield wiper blades with windshield washer fluid on a clean cloth. This will help to condition them.

Maintenance 157

Main MenustTable of Contents０３／０７／１７　０９：１０：５９　３１Ｓ５Ｂ６２０　０１６１　

Automatic Transmission Fluid

Continuously Variable Transmission (CVT)

HOT Range

UPPER MARK LOWER MARK

4.

5.

Remove the dipstick and check the fluid level. It should be between the upper and lower marks within the HOT range.

If the level is below the lower mark, add fluid into the filler hole to bring it to the level between the upper and lower marks.

DIPSTICK

Check the fluid level with the engine at normal operating temperature. 1.

Park the vehicle on level ground. Shut off the engine.

2.

Remove the dipstick (yellow loop) from the transmission, and wipe it with a clean cloth.

3.

Insert the dipstick all the way into the transmission securely.

158

Maintenance

Always use Honda ATF-Z1
(Automatic Transmission Fluid). If it’s not available, you may use a DEXRON III automatic transmission fluid as a temporary replacement. However, continued use can affect the shift quality. Have the transmission flushed and refilled with Honda ATF-Z1 as soon as it is convenient.

To thoroughly flush the transmission, the technician should drain and refill it with Honda ATF-Z1, then drive the vehicle for a short distance. Do this three times. Then drain and refill the transmission a final time.

6.

Insert the dipstick all the way back in the transmission.

The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule.

Main MenustTable of Contents０３／０７／１７　０９：１１：０６　３１Ｓ５Ｂ６２０　０１６２　

Manual Transmission Fluid

run out of the hole. Reinstall the filler bolt and tighten it securely.

If Honda MTF is not available, you may use an SAE 10W-30 or 10W-40
viscosity motor oil with the API Certification seal that says ‘‘FOR GASOLINE ENGINES’’ as a temporary replacement. However, motor oil does not contain the proper additives, and continued use can cause stiffer shifting. Replace as soon as it is convenient.

The transmission should be drained and refilled with new fluid according to the time and distance recommen- dations in the maintenance schedule.

5-speed Manual Transmission

FILLER BOLT

Correct Level

Check the fluid level with the transmission at normal operating temperature and the vehicle sitting on level ground. Remove the under- cover to access the transmission ). Remove the housing (see page transmission filler bolt and carefully feel inside the bolt hole with your finger. The fluid level should be up to the edge of the bolt hole. If it is not, add Honda Manual Transmis- sion Fluid (MTF) until it starts to

153

Maintenance

159

Main MenustTable of Contents０３／０７／１７　０９：１１：２０　３１Ｓ５Ｂ６２０　０１６３　

Brake and Clutch Fluid

Check the brake fluid level in the reservoirs monthly.

Brake System

Clutch System ManualTransmissiononly

MAX

Replace it according to the time recommendation in the maintenance schedule.

Always use Honda Heavy Duty Brake Fluid DOT 3. If it is not available, you should use only DOT 3
or DOT 4 fluid, from a sealed container, as a temporary replacement. Using any non-Honda brake fluid can cause corrosion and decrease the life of the system. Have the brake system flushed and refilled with Honda Heavy Duty Brake Fluid DOT 3 as soon as possible.

Brake fluid marked DOT 5 is not compatible with your vehicle’s braking system and can cause extensive damage.

160

Maintenance

MAX MIN

MIN

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If the level is at or below the MIN mark, your brake system needs attention. Have the brake system inspected for leaks or worn brake pads.

The fluid level should be between the MIN and MAX marks on the side of the reservoir. If it is not, add brake fluid to bring it up to that level. Use the same fluid specified for the brake system.

Low fluid level can indicate a leak in the clutch system. Have this system inspected as soon as possible.

Main MenustTable of Contents０３／０７／１７　０９：１１：３１　３１Ｓ５Ｂ６２０　０１６４　

PIVOTS

Headlight Aiming The headlights were properly aimed when your vehicle was new. If you regularly carry heavy items in the trunk, readjustment may be required. Adjustments should be performed by a Honda dealer or other qualified mechanic.

LATCH ASSEMBLY

Clean the hood latch assembly with a mild cleaner, then lubricate it with a multipurpose grease. Lubricate all the moving parts (as shown), including the pivot. Follow the time and distance recommendations in the Maintenance Schedule. If you are not sure how to clean and grease the latch, contact your Honda dealer.

Hood Latch, Lights

Replacing a Headlight Bulb Your vehicle has halogen headlight bulb. Handle it by its plastic case and protect the glass from contact with your skin or hard objects. If you touch the glass, clean it with denatured alcohol and a clean cloth.

NOTE: Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch on the glass can cause the bulb to overheat and shatter.

CONTINUED

Maintenance

161

Main MenustTable of Contents０３／０７／１７　０９：１１：４４　３１Ｓ５Ｂ６２０　０１６５　

Lights

HOLDING CLIP

BULB

CONNECTOR

TAB

1.

Open the hood. If you need to change the headlight bulb on the driver’s side, remove the holding clip from the stay with a flat-tipped screwdriver, then remove the upper part of the washer fluid reservoir tank by pulling it out.

2.

Remove the electrical connector from the bulb by pushing on the tab and pulling the connector down.

3.

Remove the bulb by turning it one- quarter turn counterclockwise.

162

Maintenance

4.

5.

Insert the new bulb into the hole and turn it one-quarter turn clock- wise to lock it in place.

Push the electrical connector back onto the bulb. Make sure it is on all the way.

6.

Turn on the headlights to test the new bulb.

7.

(Driver’s side) Reinstall the upper part of the windshield washer reservoir. Install the holding clip on the stay and lock it by pushing on the center of clip.

Main MenustTable of Contents０３／０７／１７　０９：１１：５７　３１Ｓ５Ｂ６２０　０１６６　

Replacing the Front Side Marker/ Turn Signal and Parking Light Bulb

HOLDING CLIP

BULB

SOCKET

1.

If you are changing the bulb on the driver’s side, start the engine, turn the steering wheel all the way to the right, and turn off the engine. If you are changing the bulb on the passenger’s side, turn the steering wheel to the left.

2.

Use a flat-tipped screwdriver to remove the holding clip from the inner fender, and pull the inner fender cover back.

3.

Remove the socket from the headlight assembly by turning it one-quarter turn counterclockwise.

Lights

4.

Remove the bulb from the socket by pushing it in and turning the bulb counterclockwise until it unlocks.

5.

Install the new bulb in the socket. Turn it clockwise to lock it in place.

6.

Insert the socket back into the headlight assembly. Turn it clockwise to lock it in place.

7.

Test the lights to make sure the new bulb is working.

8.

Put the inner fender cover in place. Install the holding clip. Lock it in place by pushing on the center.

Maintenance

163

Main MenustTable of Contents０３／０７／１７　０９：１２：１０　３１Ｓ５Ｂ６２０　０１６７　

Lights

Replacing Rear Bulbs (in Fenders)

BULBS

SOCKETS

FASTENERS

1.

Open the trunk.

Remove the screws in the center of each of the two fasteners on the side of the trunk lining. Pull the lining back.

2.

Determine which of the two bulbs is burned out: stop/taillight/side marker light or turn signal light.

3.

Remove the socket by turning it one-quarter turn counterclockwise.

164

Maintenance

4.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

5.

Reinstall the socket into the light assembly by turning it clockwise until it locks.

6.

Test the lights to make sure the new bulb is working.

7.

8.

Reinstall the trunk lining. Make sure it is installed under the edge of the trunk seal.

Put the fasteners into the holes on the side of the trunk lining. Reinstall the screws.

Main MenustTable of Contents０３／０７／１７　０９：１２：２３　３１Ｓ５Ｂ６２０　０１６８　

Replacing Rear Bulbs (in Trunk Lid)

4.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

BULBS

5.

Insert the socket back into the light assembly. Turn it clockwise to lock it in place.

6.

Test the lights to make sure the new bulb is working.

SOCKETS

1.

Open the trunk.

2.

Determine which of the two bulbs is burned out: taillight or back-up light.

3.

Remove the socket by turning it one-quarter turn counterclockwise.

Lights

Replacing a High-mount Brake Light Bulb

BULB

SOCKET

1.

2.

Open the trunk and remove the socket from the light assembly by turning it one-quarter turn counter- clockwise.

Pull the bulb straight out of its socket. Push the new bulb straight into the socket until it bottoms.

CONTINUED

Maintenance

165

Main MenustTable of Contents０３／０７／１７　０９：１２：３４　３１Ｓ５Ｂ６２０　０１６９　

Lights, Seat Belts, Floor Mats

3.

Reinstall the socket. Turn it clockwise until it locks. Make sure the new bulb is working.

Seat Belts

Floor Mats

LOOP

If your seat belts get dirty, use a soft brush with a mixture of mild soap and warm water to clean them. Do not use bleach, dye, or cleaning solvents. Let the belts air dry before you use the vehicle. Dirt build-up in the loops of the seat belt anchors can cause the belts to retract slowly. Wipe the insides of the loops with a clean cloth dampened in mild soap and warm water or isopropyl alcohol.

Onmodelsequipped The driver’s floor mat that came with your vehicle hooks over the floor mat anchor. This keeps the floor mat from sliding forward and possibly interfering with the pedals.

If you remove the driver’s floor mat, make sure to re-anchor it when you put it back in your vehicle.

166

Maintenance

Main MenustTable of Contents０３／０７／１７　０９：１２：４１　３１Ｓ５Ｂ６２０　０１７０　

Floor Mats, Dust and Pollen Filter

If you use a non-Honda floor mat, make sure it fits properly and that it can be used with the floor mat anchor. Do not put additional floor mats on top of the anchored mat.

Dust and Pollen Filter This filter removes the dust and pollen that is brought in from the outside through the heating and cooling system.

Have your Honda dealer replace this filter every 30,000 miles (48,000 km) under normal conditions. It should be replaced every 15,000 miles (24,000 km) if you drive primarily in urban areas that have high concentrations of soot in the air, or if the flow from the heating and cooling system becomes less than usual.

Maintenance

167

Main MenustTable of Contents０３／０７／１７　０９：１２：４８　３１Ｓ５Ｂ６２０　０１７１　

Wiper Blades

Check the condition of the wiper blades at least every six months. Replace them if you find signs of cracking in the rubber, areas that are getting hard, or if they leave streaks and unwiped areas when used.

1.

Raise the wiper arm off the windshield.

LOCK TAB

BLADE

2.

Disconnect the blade assembly from the wiper arm by pushing in the lock tab. Hold the lock tab in while you push the blade assembly toward the base of the arm.

3.

Remove the blade from its holder by grasping the tabbed end of the blade. Pull firmly until the tabs come out of the holder.

168

Maintenance

Main MenustTable of Contents０３／０７／１７　０９：１２：５８　３１Ｓ５Ｂ６２０　０１７２　

BLADE

5.

Slide the new wiper blade into the holder until the tabs lock.

6.

Slide the wiper blade assembly onto the wiper arm. Make sure it locks in place.

7.

Lower the wiper arm down against the windshield.

REINFORCEMENT

4.

Examine the new wiper blades. If they have no plastic or metal rein- forcement along the back edge, remove the metal reinforcement strips from the old wiper blade, and install them in the slots along the edge of the new blade.

Wiper Blades, Tires

Tires To safely operate your vehicle, your tires must be the proper type and size, in good condition with adequate tread, and correctly inflated.

The following pages give more detailed information on how to take care of your tires and what to do when they need to be replaced.

Using tires that are excessively worn or improperly inflated can cause a crash in which you can be seriously hurt or killed.

Follow all instructions in this owner’s manual regarding tire inflation and maintenance.

Maintenance

169

Main MenustTable of Contents０３／０７／１７　０９：１３：１３　３１Ｓ５Ｂ６２０　０１７３　

RecommendedTirePressuresfor NormalDriving The following chart shows the recommended cold tire pressures for most normal driving conditions and speed.

Tire Size

P185/70R14 87S

Cold Tire Pressure for Normal Driving 30 psi (210 kPa , 2.1
kgf/cm )

TirePressureAdjustmentforHigh SpeedDriving Honda strongly recommends that you not drive faster than posted speed limits and conditions allow. If you decide it is safe to drive at high speeds, be sure to adjust the cold tire pressures as shown in the next column. If you do not adjust the tire pressure, excessive heat can build up and cause sudden tire failure.

The compact spare tire pressure is: 60 psi (420 kPa , 4.2 kgf/cm )

Tire Size

P185/70R14 87S

Cold Tire Pressure for Speed over 100
mph (160 km/h) 35 psi (240 kPa , 2.4
kgf/cm )

Tires

Inflation Keeping the tires properly inflated provides the best combination of handling, tread life, and riding comfort.

Underinflated tires wear unevenly, adversely affect handling and fuel economy, and are more likely to fail from being overheated.

Overinflated tires can make your vehicle ride more harshly, are more prone to damage from road hazards, and wear unevenly.

We recommend that you visually check your tires every day. If you think a tire might be low, check it immediately with a tire gauge.

170

Maintenance

Main MenustTable of Contents０３／０７／１７　０９：１３：２５　３１Ｓ５Ｂ６２０　０１７４　

For convenience, the recommended tire sizes and cold air pressures are on a label on the driver’s doorjamb.

Add or release air, if needed, to match the recommended cold tire pressures on page 170 .

For additional technical information, see page

206

Use a gauge to measure the air pressure at least once a month. Even tires that are in good condition may lose one to two psi (10 to 20 kPa, 0.1
to 0.2 kgf/cm ) per month. Remember to check the spare tire at thesametime.

Check the pressure in the tires when they are cold. This means the vehicle has been parked for at least three hours, or driven less than 1 mile (1.6
km).

If you check the pressure when the tires are hot (driven for several miles), you will see readings 4 to 6
psi (30 to 40 kPa, 0.3 to 0.4 kgf/cm ) higher than the cold reading. This is normal; do not release air to match the cold pressure.

Tubeless tires have some ability to self-seal if they are punctured. You should look closely for punctures if a tire starts losing pressure.

You should get your own tire pressure gauge and use it whenever you check your tire pressures. This will make it easier for you to tell if a pressure loss is due to a tire problem and not due to a variation between gauges.

Tires

Tire Inspection Every time you check inflation, you should also examine the tires for damage, foreign objects, and wear. You should look for:

Bumps or bulges in the tread or side of the tire. Replace the tire if you find either or these conditions.

Cuts, splits, or cracks in the side of the tire. Replace the tire if you can see fabric or cord.

Excessive tread wear.

CONTINUED

Maintenance

171

Main MenustTable of Contents０３／０７／１７　０９：１３：３４　３１Ｓ５Ｂ６２０　０１７５　

Tires

INDICATOR LOCATION MARKS

TREAD WEAR INDICATOR

Your vehicle’s tires have wear indica- tors molded into the tread. When the tread wears down to that point, you will see a 1/2 inch (12.7 mm) wide band running across the tread. This shows there is less than 1/16 inch (1.6 mm) of tread left on the tire. A tire that is this worn gives very little traction on wet roads. You should replace the tire if you can see the tread wear indicator in three or more places around the tire.

172

Maintenance

Tire Maintenance In addition to proper inflation, correct wheel alignment helps to decrease tire wear. If you find a tire is worn unevenly, have your dealer check the wheel alignment.

Have your dealer check the tires if you feel a consistent vibration while driving. A tire should always be rebalanced if it is removed from the wheel. When you have new tires installed, make sure they are balanced. This increases riding comfort and tire life. For best results, have the installer perform a dynamic balance.

Tire Rotation

Front

Front

(Front Non-directional Tires and Wheels)

(Front Directional Tires and Wheels)

To help increase tire life and distribute wear more evenly, rotate the tires every 10,000 miles (16,000
km). Move the tires to the positions shown in the chart each time they are rotated. If you purchase directional tires, rotate only front-to- back.

Main MenustTable of Contents０３／０７／１７　０９：１３：４９　３１Ｓ５Ｂ６２０　０１７６　

Tires

Replacing Tires Replace your tires with radial tires of the same size, load range, speed rating and maximum cold tire pressure rating (as shown on the tire’s side wall). Mixing radial and bias-ply tires on your vehicle can reduce braking ability, traction, and steering accuracy. Using tires of a different size or construction can cause the ABS to work inconsistently.

It is best to replace all four tires at the same time. If that is not possible or necessary, replace the two front tires or two rear tires as a pair. Replacing just one tire can seriously affect your vehicle’s handling.

If you ever replace a wheel, make sure that the wheel’s specifications match those of the original wheels.

Installing improper tires on your vehicle can affect handling and stability. This can cause a crash in which you can be seriously hurt or killed.

Always use the size and type of tires recommended in this owner’s manual.

Wheel and Tire Specifications Wheels:

14 x 5 1/2 JJ

Tires:

P185/70R14 87S

206

for DOT tire quality

See page grading information, and page for tire size explanation. 207

Winter Driving Tires marked ‘‘M S’’ or ‘‘All Season’’ on the sidewall have an all- weather tread design suitable for most winter driving conditions.

＋

For the best performance in snowy or icy conditions, you should install snow tires or tire chains. They may be required by local laws under certain conditions.

Snow Tires If you mount snow tires on your Honda, make sure they are radial tires of the same size and load range as original tires. Mount snow tires on all four wheels. The traction provided by snow tires on dry roads may be lower than your original tires. Check with the tire dealer for maximum speed recommendations.

Maintenance

173

Main MenustTable of Contents０３／０７／１７　０９：１３：５６　３１Ｓ５Ｂ６２０　０１７７　

NOTICE: Traction devices that are the wrong size or improperly installed can damage your vehicle’s brake lines, suspension, body, and wheels. Stop driving if they are hitting any part of the vehicle.

Tires

Tire Chains Because your Honda has limited tire clearance, mount only SAE Class ‘‘S’’ cable-type traction devices, with rubber chain tensioners on the front tires. Use traction devices only when required by driving condition or local laws. Make sure they are the correct size for your tires. Metal link-type ‘‘chains’’ should not be used.

When installing cables, follow the manufacturer’s instructions, and mount them as tight as you can. Make sure they are not contacting the brake lines or suspension. Drive slowly with them installed. If you hear them coming into contact with the body or chassis, stop and investigate. Remove them as soon as you begin driving on cleared roads.

174

Maintenance

Main MenustTable of Contents０３／０７／１７　０９：１４：０４　３１Ｓ５Ｂ６２０　０１７８　

TEST INDICATOR WINDOW

Check the condition of the battery monthly by looking at the test indicator window. The label on the battery explains the test indicator’s colors.

Check the terminals for corrosion (a white or yellowish powder). To remove it, cover the terminals with a solution of baking soda and water. It will bubble up and turn brown. When this stops, wash it off with plain water. Dry off the battery with a cloth or paper towel. Coat the terminals with grease to help prevent further corrosion.

If additional battery maintenance is needed, see your Honda dealer or a qualified technician.

Battery posts,

WARNING: terminals, and related accessories contain lead and lead compounds. Wash your hands after handling.

Checking the Battery

If you need to connect the battery to a charger, disconnect both cables to prevent damaging your vehicle’s electrical system. Always disconnect the negative ( − reconnect it last.

) cable first, and

The battery gives off explosive hydrogen gas during normal operation.

A spark or flame can cause the battery to explode with enough force to kill or seriously hurt you.

Wear protective clothing and a face shield, or have a skilled mechanic do the battery maintenance.

Maintenance

175

Main MenustTable of Contents０３／０７／１７　０９：１４：１７　３１Ｓ５Ｂ６２０　０１７９　

Vehicle Storage

If you need to park your vehicle for an extended period (more than one month), there are several things you should do to prepare it for storage. Proper preparation helps prevent deterioration and makes it easier to get your vehicle back on the road. If possible, store your vehicle indoors.

Fill the fuel tank.

Block the rear wheels.

If the vehicle is to be stored for a longer period, it should be supported on jackstands so the tires are off the ground.

Leave one window open slightly (if the vehicle is being stored indoors).

Change the engine oil and filter.

Disconnect the 12 volt battery.

Wash and dry the exterior completely.

Cleantheinterior.Makesurethe carpeting, floor mats, etc. are completely dry.

Leave the parking brake off. Put the transmission in Reverse (5- speed manual) or Park (CVT).

Support the front wiper blade arms with a folded towel or rag so they do not touch the windshield.

To minimize sticking, apply a silicone spray lubricant to all door and trunk seals. Also, apply a vehiclebodywaxtothepainted surfaces that mate with the door and trunk seals.

Cover the vehicle with a ‘‘breathable’’ cover, one made from a porous material such as cotton. Non-porous materials, such as plastic sheeting, trap moisture, which can damage the paint.

Reconnect the 12 volt battery and drive your vehicle every month for about 30 minutes. This will keep the IMA battery charged and in good condition.

If you store your vehicle for 12
months or longer, have your Honda dealer perform the inspections called for in the 24 months/30,000 miles maintenance schedule (Normal Conditions) as soon as you take it out of storage (see page ). The replacements called for in the maintenance schedule are not needed unless the vehicle has actually reached that time or mileage.

147

176

Maintenance

Main MenustTable of Contents０３／０７／１７　０９：１４：２３　３１Ｓ５Ｂ６２０　０１８０　

Taking Care of the Unexpected

This section covers the more common problems that motorists experience with their vehicles. It gives you information about how to safely evaluate the problem and what to do to correct it. If the problem has stranded you on the side of the road, you may be able to get going again. If not, you will also find instructions on getting your vehicle towed.

Compact Spare Tire Changing a Flat Tire If the Engine Won’t Start Jump Starting If the Engine Overheats Low Oil Pressure Indicator Charging System Indicator Malfunction Indicator Lamp Brake System Indicator Fuses Fuse Locations Emergency Towing

...................... .................... ............. ................................ .............. ......... .......... ....... ............... .............................................. .............................. ......................

. 178
. 179
. 184
. 186
. 187
. 190
. 191
. 192
. 193
. 194
. 197
. 199

Taking Care of the Unexpected 177

Main Menust０３／０７／１７　０９：１４：３３　３１Ｓ５Ｂ６２０　０１８１　

Compact Spare Tire

Use the compact spare tire as a temporary replacement only. Get your regular tire repaired or replaced and put it back on your vehicle as soon as you can.

Check the inflation pressure of the compact spare tire every time you check the other tires. It should be inflated to: 60 psi (420 kPa , 4.2 kgf/cm )

178

Taking Care of the Unexpected

Follow these precautions:

INDICATOR LOCATION MARK

Never exceed 50 mph (80 km/h).

This tire gives a harsher ride and less traction on some road sur- faces. Use greater caution while driving.

Do not mount snow chains on it.

Do not use your compact spare tire on another vehicle unless it is the same make and model.

TREAD WEAR INDICATOR BAR

Replace the tire when you can see the tread wear indicator bars. The replacement should be the same size and design tire, mounted on the same wheel. The spare tire is not designed to be mounted on a regular wheel, and the spare wheel is not designed for mounting a regular tire.

Main MenustTable of Contents０３／０７／１７　０９：１４：４４　３１Ｓ５Ｂ６２０　０１８２　

If you have a flat tire while driving, stop in a safe place to change it. Drive slowly along the shoulder until you get to an exit or an area to stop that is far away from the traffic lanes.

The vehicle can easily roll off the jack, seriously injuring anyone underneath.

Follow the directions for changing a tire exactly, and never get under the vehicle when it is supported only by the jack.

1.

2.

Park the vehicle on firm, level and non-slippery ground. Put the transmission in Park (automatic) or Reverse (manual). Apply the parking brake.

Turn on the hazard warning lights, and turn the ignition switch to LOCK (0). Have all the passengers get out of the vehicle while you change the tire.

Changing a Flat Tire

SPARE TIRE

TRUNK FLOOR

TOOL KIT JACK Open the trunk. Raise the trunk 3. floor mat and the trunk floor by lifting up on the back edge.

4.

Take the tool kit out of the trunk.

5.

Unscrew the wing bolt and take the spare tire out of its well.

CONTINUED

Taking Care of the Unexpected 179

Main MenustTable of Contents０３／０７／１７　０９：１４：５２　３１Ｓ５Ｂ６２０　０１８３　

Changing a Flat Tire

JACK

JACKING POINTS

6.

Turn the jack’s end counterclockwise to loosen it, then remove the jack.

WHEEL WRENCH

7.

Loosen each wheel nut 1/2 turn with the wheel wrench.

8.

Place the jack under the jacking point. Turn the end bracket clockwise until the top of the jack contacts the jacking point. Make sure the jacking point tab is resting in the jack notch.

180

Taking Care of the Unexpected

Main MenustTable of Contents０３／０７／１７　０９：１５：０２　３１Ｓ５Ｂ６２０　０１８４　

EXTENSION

WHEEL WRENCH Use the extension and wheel 9. wrench as shown to raise the vehicle until the flat tire is off the ground.

10.

Remove the flat tire. Place the flat tire on the ground with the outside surface facing up.

Changing a Flat Tire

BRAKE HUB

11.

Before mounting the spare tire, wipe any dirt off the mounting surface of the wheel and hub with a clean cloth. Wipe the hub carefully; it may be hot from driving.

CONTINUED

Taking Care of the Unexpected 181

Main MenustTable of Contents０３／０７／１７　０９：１５：１５　３１Ｓ５Ｂ６２０　０１８５　

Changing a Flat Tire

WING BOLT

SPACER CONE

12.

Put on the spare tire. Put the wheel nuts back on finger-tight, then tighten them in a crisscross pattern with the wheel wrench until the wheel is firmly against the hub. Do not try to tighten them fully.

13.

Lower the vehicle to the ground and remove the jack.

14.

Tighten the wheel nuts securely in the same crisscross pattern. Have the wheel nut torque checked at the nearest automotive service facility. Tighten the wheel nuts to: 80 lbf·ft (108 N·m , 11 kgf·m)

15.

Remove the center cap before storing the flat tire in the trunk well.

16.

Place the flat tire face down in the spare tire well.

17.

Remove the spacer cone from the wing bolt, turn it over, and put it back on the bolt.

18.

Secure the flat tire by screwing the wing bolt back into its hole.

182

Taking Care of the Unexpected

Main MenustTable of Contents０３／０７／１７　０９：１５：２１　３１Ｓ５Ｂ６２０　０１８６　

Changing a Flat Tire

19.

Store the jack in the trunk with the end bracket on the left side. Turn the jack’s end bracket to lock it in place. Store the tool kit.

Loose items can fly around the interior in a crash and could seriously injure the occupants.

Store the wheel, jack, and tools securely before driving.

20.

Store the wheel cover or center cap in the trunk. Make sure it does not get scratched or damaged.

21.

Lower the trunk floor and trunk floor mat, then close the trunk lid.

Taking Care of the Unexpected 183

Main MenustTable of Contents０３／０７／１７　０９：１５：３２　３１Ｓ５Ｂ６２０　０１８７　

If the Engine Won’t Start

Diagnosing why your engine won’t start falls into two areas, depending on what you hear when you turn the key to START (III):

You hear nothing, or almost nothing. The engine’s starter motor does not operate at all, or operates very slowly.

You can hear the starter motor operating normally, or the starter motor sounds like it is spinning faster than normal, but the engine does not start up and run.

Nothing Happens or the Starter Motor Operates Very Slowly When you turn the ignition switch to START (III), you do not hear the normal noise of the engine trying to start. You may hear a clicking sound or series of clicks, or nothing at all. Check these things:

Check the transmission interlock. If you have a manual transmission, the clutch pedal must be pushed all the way to the floor or the starter will not operate. With an automatic transmission, it must be in Park or Neutral.

Turn the ignition switch to ON (II). Turn on the headlights and check their brightness. If the headlights are very dim or don’t light at all, the battery is discharged. See Jump Starting

on page

186

184

Taking Care of the Unexpected

Turn the ignition switch to START (III). If the headlights do not dim, check the condition of the fuses. If the fuses are OK, there is probably something wrong with the electrical circuit for the ignition switch or starter motor. You will need a qualified technician to determine the Emergency Towing problem (see ). on page 199

If the headlights dim noticeably or go out when you try to start the engine, either the battery is dis- charged or the connections are corroded. Check the condition of the battery and terminal connec- tions (see page 175). You can then try jump starting the vehicle from a booster battery (see page 186

).

Main MenustTable of Contents０３／０７／１７　０９：１５：４０　３１Ｓ５Ｂ６２０　０１８８　

If the Engine Won’t Start

The Starter Operates Normally In this case, the starter motor’s speed sounds normal, or even faster than normal, when you turn the ignition switch to START (III), but the engine does not run.

Are you using a properly coded key? An improperly coded key will cause the immobilizer system indicator in the instrument panel to blink rapidly (see page

71

).

Do you have fuel? Check the fuel gauge; the low fuel indicator may not be working.

There may be an electrical problem, such as no power to the fuel pump. Check all the fuses (see page

194

).

Ifyoufindnothingwrong,youwill need a qualified technician to find the problem. See Towing on page

Emergency 199

Are you using the proper starting Starting the procedure? Refer to Engine 129

on page

Taking Care of the Unexpected 185

Main MenustTable of Contents０３／０７／１７　０９：１５：５２　３１Ｓ５Ｂ６２０　０１８９　

Jump Starting

Although this seems like a simple procedure, you should take several precautions.

A battery can explode if you do not follow the correct procedure, seriously injuring anyone nearby.

Keep all sparks, open flames, and smoking materials away from the battery.

You cannot start a Honda with an automatic transmission (CVT) by pushing or pulling it.

186

Taking Care of the Unexpected

ToJumpStartYourVehicle:

1.

Open the hood, and check the physical condition of the 12 volt battery. In very cold weather, check the condition of the electrolyte. If it seems slushy or like ice, do not try jump starting until it thaws.

NOTICE: If a battery sits in extreme cold, the electrolyte inside can f reeze. Attempting to jump start with a f rozen battery can cause it to rupture.

2.

3.

Turn off all the electrical acces- sories: heater, A/C, stereo system, lights, etc. Put the transmission in Neutral or Park, and set the parking brake.

＋

) terminal on your

Connect one jumper cable to the positive ( battery. Connect the other end to the positive ( ) terminal on the ＋ booster battery.

4.

−

Connect the second jumper cable to the negative ( ) terminal on the booster battery. Connect the other end to the metal projection as shown. Do not connect this jumper cable to any other part of the engine.

5.

If the booster battery is in another vehicle, have an assistant start that vehicle and run it at a fast idle.

Main MenustTable of Contents０３／０７／１７　０９：１６：０４　３１Ｓ５Ｂ６２０　０１９０　

Jump Starting, If the Engine Overheats

6.

7.

Start your vehicle. If the starter motor still operates slowly, check that the jumper cables have good metal-to-metal contact.

Once your vehicle is running, disconnect the negative cable from your vehicle, then from the booster battery. Disconnect the positive cable from your vehicle, and then from the booster battery.

Keep the ends of the jumper cables away from each other and any metal on the vehicle until everything is disconnected. Otherwise, you may cause an electrical short.

If your vehicle’s 12 volt battery is disconnected or goes dead, the IMA battery level gauge reading may not be correct the next time you turn the ignition switch to ON (II). It may show less than the actual level temporarily. It will show the correct level after you drive for at least 30

minutes.

If the Engine Overheats The reading on your vehicle’s temperature gauge should stay in the midrange. If it climbs to the red mark, you should determine the reason (hot day, driving up a steep hill, etc.).

If your vehicle overheats, you should take immediate action. The only indication may be the temperature gauge climbing to or above the red mark. Or you may see steam or spray coming from under the hood.

Driving with the

NOTICE: temperature gauge pointer at the red mark can cause serious damage to your engine.

Steam and spray from an overheated engine can seriously scald you.

Do not open the hood if steam is coming out.

CONTINUED

Taking Care of the Unexpected

187

Main MenustTable of Contents０３／０７／１７　０９：１６：１４　３１Ｓ５Ｂ６２０　０１９１　

If the Engine Overheats

1.

2.

Safely pull to the side of the road. Put the transmission in Neutral or Park, and set the parking brake. Turn off all the accessories, and turn on the hazard indicator.

If you see steam and/or spray coming from under the hood, turn off the engine. Wait until you see no more signs of steam or spray, then open the hood.

3.

If you do not see steam or spray, leave the engine running and watch the temperature gauge. If the high heat is due to overloading, the engine should start to cool down almost immediately. If it does, wait until the temperature gauge comes down to the midpoint, then continue driving.

4.

If the temperature gauge stays at the red mark, turn off the engine.

5.

Look for any obvious coolant leaks, such as a split radiator hose. Everything is still extremely hot, so use caution. If you find a leak, it must be repaired before you Emergency continue driving (see Towing ). 199

on page

6.

If you don’t find an obvious leak, check the coolant level in the radiator reserve tank. Add coolant if the level is below the MIN mark.

188

Taking Care of the Unexpected

Main MenustTable of Contents０３／０７／１７　０９：１６：２１　３１Ｓ５Ｂ６２０　０１９２　

If the Engine Overheats

7.

If there was no coolant in the reserve tank, you may need to add coolant to the radiator. Let the engine cool down until the reading reaches the middle of the temperature gauge, or lower, before checking the radiator.

Removing the radiator cap while the engine is hot can cause the coolant to spray out, seriously scalding you.

Always let the engine and radiator cool down before removing the radiator cap.

8.

9.

Using gloves or a large heavy cloth, turn the radiator cap counterclockwise without pushing down to the first stop. After the pressure releases, push down on the cap, and turn it until it comes off.

Start the engine, and set the temperature control dial to maximum. Add coolant to the radiator up to the base of the filler neck. If you do not have the proper coolant mixture available, you can add plain water. Remember to have the cooling system drained and refilled with the proper mixture as soon as you can.

10.

Put the radiator cap back on tightly. Run the engine and watch the temperature gauge. If it goes back to the red mark, the engine needs repair (see Towing on page

Emergency 199

).

11.

If the temperature stays normal, check the coolant level in the radiator reserve tank. If it has gone down, add coolant to the MAX mark. Put the cap back on tightly.

Taking Care of the Unexpected

189

Main MenustTable of Contents０３／０７／１７　０９：１６：３０　３１Ｓ５Ｂ６２０　０１９３　

Low Oil Pressure Indicator

This light should never come on when the engine is running. If it starts flashing

or stays on, the oil pressure has dropped very low or lost pressure. Serious engine damage is possible and you should take immediate action.

NOTICE: Running the engine with low oil pressure can cause serious mechanical damage almost immediately. Turn of f the engine as soon as you can saf ely get the vehicle stopped.

1.

2.

3.

4.

190

Taking Care of the Unexpected

Safely pull off the road, and shut off the engine. Turn on the hazard warning indicators.

Let the vehicle sit for a minute. Open the hood, and check the oil level (see page ). An engine very low on oil can lose pressure during cornering and other driving maneuvers.

118

The engine running generates the oil pressure. When the Auto Idle Stop is activated, the engine is stopped, the oil pressure is dropped, and the low oil pressure indicator does not light.

If necessary, add oil to bring the level back to the full mark on the dipstick (see page

152

).

Start the engine, and watch the oil pressure indicator. If it does not go out within 10 seconds, turn off the engine. There is a mechanical problem that needs to be repaired before you can continue driving. Emergency Towing (See ). 199

on page

Main MenustTable of Contents０３／０７／１７　０９：１６：３７　３１Ｓ５Ｂ６２０　０１９４　

Charging System Indicator

If the charging system indicator comes on brightly when the engine is running,

the 12 volt battery is not being charged.

Immediately turn off all electrical accessories. Try not to use other electrically operated controls such as the power windows and rear window defogger. Keep the engine running; starting the engine will discharge the battery rapidly.

Go to a service station or garage where you can get technical assistance.

If the Auto Idle Stop is active for an extended period, the charging system indicator may come on. If it happens, start the engine.

The charging system indicator may also come on if the Integrated Motor Assist (IMA) battery charge drops below a desired level and the engine starts to recharge the battery.

This indicator may blink after you start the vehicle in the morning when the temperature is below 20
− °F ( 30°C). It will stop blinking when the IMA battery warms up.

−

Taking Care of the Unexpected

191

Main MenustTable of Contents０３／０７／１７　０９：１６：４９　３１Ｓ５Ｂ６２０　０１９５　

Malfunction Indicator Lamp

If the indicator comes on while driving, it means one of the engine’s emission

control systems may have a problem. Even though you may feel no difference in your vehicle’s performance, it can reduce your fuel economy and cause increased emissions. Continued operation may cause serious damage.

If you have recently refueled your vehicle, the indicator coming on could be a loose or missing fuel fill cap. Tighten the cap until it clicks at least three times. Tightening the cap will not turn the indicator turn off immediately; it takes at least three days of normal driving.

192

Taking Care of the Unexpected

If the indicator comes on repeatedly, even though it may turn off as you continue driving, have the vehicle checked by the dealer as soon as possible.

If your vehicle battery has been disconnected or gone dead, these codes are erased. It takes at least three days of driving under various conditions to set the codes again.

NOTICE: If you keep driving with the Malf unction Indicator Lamp on, you can damage your vehicle’s emission controls and the engine. Those repairs may not be covered by your vehicle’s warranties.

Readiness Code Your vehicle has certain ‘‘readiness codes’’ that are part of the on-board diagnostics for the emissions systems. In some states, part of the emissions testing is to make sure these codes are set. If they are not set, the test cannot be completed.

To check if they are set, turn the ignition to ON (II), without starting the engine. The Malfunction Indicator Lamp will come on for 20
seconds. If it then goes off, the readiness codes are set. If it blinks 5
times, the readiness codes are not set. If possible, do not take your vehicle for a state emissions test until the readiness codes are set. Refer to State Emissions Testing for more information (see page

211

).

Main MenustTable of Contents０３／０７／１７　０９：１６：５７　３１Ｓ５Ｂ６２０　０１９６　

U.S.

Canada

The brake system indicator normally comes on when you turn the ignition switch ON (II) and as a reminder to check the parking brake. It will stay lit if you do not fully release the parking brake.

If the brake system indicator comes on while driving, the brake fluid level is probably low. Press lightly on the brake pedal to see if it feels normal. If it does, check the brake fluid level thenexttimeyoustopataservice station (see page

160

).

If the fluid level is low, take your vehicle to the dealer and have the brake system inspected for leaks or worn brake pads.

However, if the brake pedal does not feel normal, you should take immediate action. A problem in one part of the system’s dual circuit

Brake System Indicator

OnmodelsequippedwithABS If the ABS indicator comes on with this indicator, have the vehicle inspected by your Honda dealer immediately.

design will still give you braking at two wheels. You will feel the brake pedal go down much farther before the vehicle begins to slow down and you will have to press harder on the pedal.

Slow down by shifting to a lower gear, and pull to the side of the road when it is safe. Because of the long distance needed to stop, it is hazardous to drive the vehicle. You should have it towed and repaired as soon as possible (see Towing on page 199).

Emergency

If you must drive the vehicle a short distance in this condition, drive slowly and carefully.

Taking Care of the Unexpected

193

Main MenustTable of Contents０３／０７／１７　０９：１７：０６　３１Ｓ５Ｂ６２０　０１９７　

Fuses

INTERIOR

UNDER-HOOD FUSE BOX

SECONDARY FUSE BOX

TAB

TAB

The vehicle’s fuses are located in threefuseboxes.Theinteriorfuse box is located underneath the steering column. To open it, turn the knobsasshown.

The under-hood fuse box is located in the engine compartment on the driver’s side.

The secondary fuse box is located in the engine compartment.

194

Taking Care of the Unexpected

Checking and Replacing Fuses If something electrical in your vehicle stops working, check for a blown fuse first. Determine from the chart on pages or the diagram on the fuse box lid, which fuses control that device. Check those fuses first, but check all the fuses before deciding that a blown fuse is the cause. Replace any blown fuses, and check if the device works.

and

197

198

Main MenustTable of Contents０３／０７／１７　０９：１７：１８　３１Ｓ５Ｂ６２０　０１９８　

FUSE

BLOWN

BLOWN

1.

Turn the ignition switch to LOCK (0). Make sure the headlights and all other accessories are off.

2.

Remove the cover from the fuse box.

3.

Check each of the large fuses in the under-hood fuse box by looking through the top at the wire inside. Remove the screws with a phillips-head screwdriver.

4.

Check the smaller fuses in the under-hood fuse box and all the fuses in the interior fuse box by pulling out each fuse with the fuse puller provided in the under-hood fuse box.

5.

Look for a burned wire inside the fuse. If it is burned, replace it with one of the spare fuses of the same rating or lower.

Fuses

If you cannot drive the vehicle without fixing the problem, and you do not have a spare fuse, take a fuse of the same rating or a lower rating from one of the other circuits. Make sure you can do without that circuit temporarily (such as the accessory power socket or radio).

If you replace the blown fuse with a spare fuse that has a lower rating, it might blow out again. This does not indicate anything wrong. Replace the fuse with one of the correct rating as soon as you can.

Replacing a f use with one

NOTICE: that has a higher rating greatly increases the chances of damaging the electrical system. If you do not have a replacement f use with the proper rating f or the circuit, install one with a lower rating.

Taking Care of the Unexpected 195

Main MenustTable of Contents０３／０７／１７　０９：１７：２３　３１Ｓ５Ｂ６２０　０１９９　

When the audio system is disabled, the clock setting in the audio system will be canceled. You will need to reset the clock according to the instructions in the audio system section on this owner’s manual.

Fuses

6.

If the replacement fuse of the same rating blows in a short time, there is probably a serious electrical problem in your vehicle. Leave the blown fuse in that circuit and have your vehicle checked by a qualified mechanic.

If the radio fuse is removed, the audio system will disable itself. The nexttimeyouturnontheradioyou will see ‘‘COdE’’ in the frequency display. Use the Preset buttons to enter the five-digit code (see page 107

).

196

Taking Care of the Unexpected

Main MenustTable of Contents０３／０７／１７　０９：１７：３１　３１Ｓ５Ｂ６２０　０２００　

UNDER-HOOD AND SECONDARY FUSE BOXES

No. Amps.

Circuits Protected

Fuse Locations

10
11
12
13
14
15
16
17
18
19
20
−

20 A 10 A 10 A 20 A 10 A 15 A 15 A 20 A 10 A 40 A 30 A 40 A 40 A 40 A 20 A 20 A 20 A 60 A 80 A 50 A −

21 25 7.5A 30A

Condenser Fan IMA Small Light Cooling Fan Hazard FI ECU Horn, Stop ABS F/S Back Up ABS Motor Rear Defroster Heater Motor Power Window Option Left Headlight Door Lock Right Headlight EPS Battery Ignition 1
Spare Fuses

Taking Care of the Unexpected

197

No. Amps.

Circuits Protected

20 A

Cooling Fan

Main MenustTable of Contents０３／０７／１７　０９：１７：３９　３１Ｓ５Ｂ６２０　０２０１　

Fuse Locations

INTERIOR FUSE BOX

No. Amps.

Circuits Protected

10
11
12
13
14
15