Multi-Information Display
Alarm off
Alarm on
Select either of the setting modes (1
or 2), then select on or off by
pressing the SEL/RESET button
repeatedly.
To adjust the setting speed, select either of the setting speeds, then press and hold the SEL/RESET button. The display changes to the speed setting screen.
The displayed number is the current speed setting. Select either the or icon by pressing the INFO button − repeatedly, then press the SEL/ RESET button to change the setting value.
+
114
Instruments and Controls
06/12/06 10:44:12 32SMR600_118
Each time you press the SEL/ RESET button, the setting speed increases or decreases by 5 km/h (mph). You can set the speed values over 5 km/h (5 mph) with 5 km/h (mph) steps. Always follow the posted speed limit and never drive faster than is safe for the traffic conditions.
To enter your selection, select the SET icon by pressing the INFO button, then press and hold the SEL/ RESET button.
After your selection, press and release the INFO button to move to the exit mode. Press the SEL/ RESET button to enter your setting. If you press the INFO button, the display goes back to the setting mode. Repeat the setup.
Multi-Information Display
Toselectthealarmspeedwhiledriving:
To exit the customizing mode, select the exit mode shown above by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
Press the INFO button for about 1
second to switch the display. You will
see the speed alarm settings on the
multi-information display.
CONTINUED
Instruments and Controls 115
06/12/06 10:44:19 32SMR600_119
Multi-Information Display
According to the selected display, you can select the alarm speed between the two setting speeds: 50 km/h and 80 km/h in km/h mode, or 30 mph and 50 mph in mph mode. Each time you press and release the INFO button, the selected icon is changed between the setting speeds and the exit icon.
116
Instruments and Controls
Alarm off
Alarm on
Alarm on
Select the desired setting speed, then press the SEL/RESET button. Each time you press the SEL/ RESET button, the selected speed icon switches between on and off. After your selection, press and release the INFO button to move to the exit mode. Press the SEL/ RESET button to enter your setting. If you press the INFO button, the display goes back to the setting mode. Repeat the setup.
After pressing the SEL/RESET button, the display shows your setting for a few seconds, then goes back to the normal display.
If you do not press any button, the display returns to the normal display after about 10 seconds.
06/12/06 10:44:30 32SMR600_120
Multi-Information Display
Change Setting You can customize some of the vehicle control settings to suit your needs. The following items are the settings you can customize.
WARNING MESSAGE: The warning message is displayed with ). the symbol or not (see page
118
ADJUST OUTSIDE TEMP. DISPLAY: The outside temperature indicator value is adjustable up to page
+ −
120
or
).
3°C (see
TRIP A RESET WITH REFUEL: Average fuel mileage for trip meter A can be reset after refueling (see page ).
121
ELAPSED TIME RESET: The elapsed time can be reset when you turn the ignition switch to the OFF (0) position or when you reset the trip meter A or B (see page
123
).
Except Type-R
Type-R
DISPLAY UNIT: Measurements in
the trip computer can be selected;
auto, km or miles (see page
).
124
This function is available on the
right-hand drive type only.
REV. INDICATOR: Rev indicator
can be turned on or off (see page
126
).
ECO. INDICATOR: ECO indicator
can be turned on or off (see page
127
).
i-VTEC. INDICATOR: i-VTEC indicator can be turned on or off (see page
129
).
CONTINUED
Instruments and Controls 117
06/12/06 10:44:37 32SMR600_121
Multi-Information Display
Press and hold the INFO button to enter the customizing mode, then press and release the INFO button repeatedly to select ‘‘CHG SETTING.’’ While the multi-information display is showing ‘‘CHG SETTING,’’ press the SEL/RESET button. The display changes to the setting mode.
Press and release the INFO button repeatedly until you see the setup you want to customize, and press the SEL/RESET button to enter your selection. Each time you press the INFO button, the display changes as shown. To customize each setting, follow the procedures described on the following pages.
118
Instruments and Controls
WarningMessage
To exit the customizing mode after your selection, select the exit mode shown above by pressing the INFO button repeatedly, then press the SEL/RESET button. The display will return to the normal display.
You can see message(s) with the system warning symbol on the multi- information display. While the multi- information display is showing ‘‘WARNING MESSAGE,’’ press the SEL/RESET button. The display changes to the setting display.
06/12/06 10:44:45 32SMR600_122
Multi-Information Display
You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display shows ‘‘SETUP ON’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode. If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode.
Repeat the setup.
To exit the customizing mode, select
the exit mode by pressing the INFO
button repeatedly, then press the
SEL/RESET button (see page
118
The display goes back to the
‘‘WARNING MESSAGE’’ display.
To return to the normal display,
select the
the SEL/RESET button.
display, then press
).
CONTINUED
Instruments and Controls 119
06/12/06 10:44:51 32SMR600_123
Multi-Information Display
OutsideTemperatureDisplay Adjustment If you find that the temperature reading is always a few degrees below or above the actual temperature, adjust it as described on the following columns.
120
Instruments and Controls
While the multi-information display is showing ‘‘ADJUST OUTSIDE TEMP. DISPLAY,’’ press the SEL/ RESET button. The display changes to the setting display.
or
+ −
The highlighted number is the current adjustment above or below the outside temperature. Select either icon by pressing the INFO button repeatedly then press the SEL/RESET button to change the setting value. You can select the 3, and 0, value between 0, 3. To enter your selection, − − − select the SET icon by pressing the INFO button, then press the SEL/ RESET button.
+ + +
1,
2,
1,
2,
06/12/06 10:44:58 32SMR600_124
±
°C’’ for a few seconds,
When your selection is successfully completed, the display shows ‘‘SETUP then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode.
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
Multi-Information Display
TripAResetWithRefuel
To cause the trip meter A and the average fuel mileage for trip A to reset every time you refuel your vehicle, adjust it as described as follows.
While the multi-information display is showing ‘‘TRIP A RESET WITH REFUEL,’’ press the SEL/RESET button. The display changes to the setting display.
CONTINUED
Instruments and Controls 121
06/12/06 10:45:04 32SMR600_125
Multi-Information Display
You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.
When your selection is successfully completed, the display shows ‘‘SETUP ON’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/ RESET button, then press the INFO button repeatedly to select another customizing mode.
122
Instruments and Controls
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display will return to the normal display.
06/12/06 10:45:12 32SMR600_126
ElapsedTimeReset
To cause the elapsed time to reset every time you turn the ignition switch to the LOCK (0) position or reset the trip meter A or B, adjust it as described as follows.
While the multi-information display is showing ‘‘ELAPSED TIME RESET,’’ press the SEL/RESET button. The display changes to the setting display.
You can select ‘‘IGN OFF,’’ ‘‘TRIP A,’’ or ‘‘TRIP B’’. Each time you press the INFO button, the selected mode switches between them. Enter your selection by pressing the SEL/RESET button.
Multi-Information Display
IGN OFF: The elapsed time is reset when you turn the ignition switch to the LOCK (0) position.
TRIP A: The elapsed time is reset when you reset the trip meter A.
TRIP B: The elapsed time is reset when you reset the trip meter B.
CONTINUED
Instruments and Controls 123
06/12/06 10:45:19 32SMR600_127
Multi-Information Display
IGN OFF is selected.
When your selection is successfully completed, the display shows the appropriate setting; ‘‘SETTING IGN OFF,’’ ‘‘SETUP TRIP A,’’ or ‘‘SETUP TRIP B’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.
124
Instruments and Controls
DisplayUnit
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
Ontheright-handdrivetypeonly You can select the measurement standard in the trip computer as described as follows. There are three selectable modes; AUTO, KM and MILES.
06/12/06 10:45:27 32SMR600_128
AUTO: The displayed measurements of the trip computer on the multi- information display correspond with the speedometer display setting. The display switches between ‘‘km’’ and ‘‘miles.’’
KM: The displayed measurements of the trip computer on the multi- information display do not correspond to the speedometer display switching. Always display with ‘‘km.’’
MILES: The displayed measurements of the trip computer on the multi-information display do not correspond to the speedometer display switching. Always display with ‘‘miles.’’
You can select ‘‘AUTO,’’ ‘‘KM,’’ or ‘‘MILES’’. Each time you press the INFO button, the selected mode switches between them. Enter your selection by pressing the SEL/ RESET button.
While the multi-information display is showing ‘‘DISPLAY UNIT,’’ press the SEL/RESET button. The display changes to the setting display.
Multi-Information Display
AUTO is selected.
When your selection is successfully completed, the display shows the appropriate setting; ‘‘SETUP AUTO,’’ ‘‘SETUP KM,’’ or ‘‘SETUP MILES’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.
CONTINUED
Instruments and Controls 125
06/12/06 10:45:33 32SMR600_129
Multi-Information Display
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
REVIndicator
You can select the REV indicator in the instrument panel. While the multi-information display is showing ‘‘REV. INDICATOR,’’ press the SEL/RESET button. The display changes to the setting display.
You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.
126
Instruments and Controls
06/12/06 10:45:41 32SMR600_130
ON is selected.
When your selection is successfully completed, the display shows ‘‘SETUP ON’’ or ‘‘SETUP OFF’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
Onvehicleswithi-SHIFT In the automatic driving mode, the REV indicator goes out even if the setting is on.
Multi-Information Display
ECOIndicator ExceptType-R
You can display the ECO indicator in the instrument panel. While the multi-information display is showing ‘‘ECO. INDICATOR,’’ press the SEL/RESET button. The display changes to the setting display.
CONTINUED
Instruments and Controls 127
06/12/06 10:45:48 32SMR600_131
Multi-Information Display
You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.
ON is selected.
When your selection is successfully completed, the display shows ‘‘SETUP ON’’ or ‘‘SETUP OFF’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.
128
Instruments and Controls
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
06/12/06 10:45:54 32SMR600_132
i-VTECIndicator Type-Rmodelonly
You can display the i-VTEC indicator in the instrument panel. While the multi-information display is showing ‘‘i-VTEC INDICATOR,’’ press the SEL/RESET button. The display changes to the setting display.
You can select ‘‘ON’’ or ‘‘OFF’’. Each time you press the INFO button, the selected mode switches between on and off. Enter your selection by pressing the SEL/RESET button.
Multi-Information Display
ON is selected.
When your selection is successfully completed, the display shows ‘‘SETUP ON’’ or ‘‘SETUP OFF’’ for a few seconds, then goes back to the ‘‘CHG SETTING’’ display. Press the SEL/RESET button, then press the INFO button repeatedly to select another customizing mode.
CONTINUED
Instruments and Controls 129
06/12/06 10:46:01 32SMR600_133
Multi-Information Display
If you fail to enter your selection, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
Selecting Language
Press and hold the INFO button to enter the customizing mode, then press and release the INFO button to select ‘‘LANGUAGE.’’ While the multi-information display is showing ‘‘LANGUAGE,’’ press the SEL/ RESET button. The display changes to the setting display.
You can select any of the following languages: English, French, German, Spanish, Italian, Portuguese. Press and release the INFO button to select the language, then press the SEL/RESET button to enter the selection.
130
Instruments and Controls
06/12/06 10:46:07 32SMR600_134
Multi-Information Display
ENGLISH is selected.
When the language selection is successfully completed, the display changes to the screen shown above for a few seconds, then goes back to the ‘‘LANGUAGE’’ display. Press the INFO button repeatedly to select another customizing mode.
If you fail to set the language setting, you will see ‘‘INCOMPLETE’’ on the display for a few seconds. The display returns to the setting mode. Repeat the setup.
To exit the customizing mode, select the exit mode shown above by pressing the INFO button repeatedly, then press the SEL/RESET button. The display goes back to the normal display.
CONTINUED
Instruments and Controls 131
06/12/06 10:46:13 32SMR600_135
Multi-Information Display
Default Settings
If you want to set the customizable vehicle control settings to the default setting, press the INFO button on the steering wheel repeatedly until ‘‘DEFAULT ALL’’ is displayed, then press the SEL/RESET button.
The display shows the selectable items. If you want to cancel ‘‘DEFAULT ALL,’’ select ‘‘CANCEL’’ by pressing the INFO button, then press and hold the SEL/RESET button for about 3 seconds to set. The display goes back to the normal display.
To set the default settings, select ‘‘OK’’ by pressing the INFO button, then press and hold the SEL/RESET button for about 3 seconds to set.
132
Instruments and Controls
06/12/06 10:46:18 32SMR600_136
Multi-Information Display
After the DEFAULT ALL operation is completed, you will see the above display for a few seconds, then the display switches to the language setting mode.
If the DEFAULT ALL operation is not successful, you will see the above display for a few seconds, then the display goes back to the setting display.
Instruments and Controls 133
06/12/06 10:46:28 32SMR600_137
Multi-Information Display
The following are the default values for each customizable setting.
Average fuel mileage for trip meter A is not reset on refueling.
The speed alarm function is off.
The warning message function is off. Only the symbols are displayed on the multi-information display.
Outside temperature display adjustment value is 0°C.
The elapsed time is reset with the ignition switch in the LOCK (0) position.
Measurements in the trip computer correspond with the measurements selected with the mph to km/h change button (km/h or mph).
Rev indicator is on.
Onvehicleswithi-SHIFT In the automatic driving mode, the REV indicator goes out.
ECO indicator is on.
i-VTEC indicator is off.
Displayed language is English.
Default setting is selected.
134
Instruments and Controls
06/12/06 10:46:36 32SMR600_138
Left-hand drive type
VSA OFF SWITCH (P.342)
HEADLIGHTS/TURN SIGNALS/ REAR FOG LIGHT/ FRONT FOG LIGHTS (P.140, 142, 143)
*
ENGINE START BUTTON (P.318, 319, 320)
HEADLIGHT ADJUSTER (P.146)
HANDS-FREE TELEPHONE SYSTEM BUTTONS (P.280)
*
Controls Near the Steering Wheel
WINDSCREEN WIPERS/ WASHERS
(P.137)
REAR WINDOW DEMISTER/ HEATED MIRROR (P.145, 173)
INSTRUMENT PANEL (P.144) BRIGHTNESS
HAZARD WARNING BUTTON (P.145)
VOICE CONTROL BUTTONS
*
REMOTE AUDIO CONTROLS (P.269)
*
CRUISE CONTROL BUTTONS (P.276)
*
CIGARETTE LIGHTER (P.182)
HORN *
STEERING WHEEL ADJUSTMENT (P.147)
MULTI-INFORMATION BUTTONS (P.90)
* *
1 : 2 :
To use the horn, press the centre pad of the steering wheel. If equipped
CONTINUED
Instruments and Controls 135
06/12/06 10:46:44 32SMR600_139
Controls Near the Steering Wheel
Right-hand drive type
HAZARD WARNING BUTTON (P.145)
REAR WINDOW DEMISTER/ HEATED MIRROR (P.145, 173)
MULTI-INFORMATION BUTTONS (P.90)
HANDS-FREE TELEPHONE SYSTEM BUTTONS (P.280)
*
VOICE CONTROL BUTTONS
*
Without cruise control With navigation system
INSTRUMENT PANEL BRIGHTNESS (P.144)
REMOTE AUDIO CONTROLS (P.269)
*
CIGARETTE LIGHTER
(P.182)
1 : 2 :
*
*
136
To use the horn, press the centre pad of the steering wheel. If equipped Instruments and Controls
HEADLIGHTS/TURN SIGNALS/ REAR FOG LIGHT/ FRONT FOG LIGHTS (P.140, 142, 143)
*
mph to km/h CHANGE BUTTON (P.85)
VSA OFF SWITCH (P.342)
WINDSCREEN WIPERS/WASHERS (P.137)
ENGINE START BUTTON (P.318, 319, 320)
HEADLIGHT ADJUSTER (P.146)
CRUISE CONTROL BUTTONS (P.276)
*
HORN
*
STEERING WHEEL ADJUSTMENT (P.147)
MULTI-INFORMATION BUTTONS (P.90)
06/12/06 10:46:56 32SMR600_140
Windscreen Wipers and Washers
Windscreen Wipers
Push the lever up or down to select a position.
HI
−
The wipers run at high speed.
−
Windscreen Washers
Pull the wiper control lever toward you, and hold it. The washers spray until you release the lever. The wipers run at low speed, then complete one more sweep after you release the lever.
Headlight Washer (For some types) When you pull back on the wiper control lever with the headlight switch ON, the headlight washers and windscreen washers work at the same time.
The headlight washers use the same fluid reservoir as the windscreen washers.
MIST
−
The wipers run at high
speed until you release the lever.
OFF
−
The wipers are not activated.
INT
−
The length of the wiper
interval is varied automatically according to vehicle’s speed.
Vary the delay by turning the INT TIME ring.
If you turn it to the shortest delay, the wipers will change to low speed operation when the vehicle speed exceeds 20 km/h (12 mph).
While the vehicle is stopped and in gear, the wipers sweep the windscreen whenever you remove your foot from the brake pedal.
LO
−
The wipers run at low speed.
CONTINUED
Instruments and Controls 137
1. 2. 3.
4. 5. 6.
−
Intermittent
MIST OFF INT (AUTO ) LO Low speed HI High speed Windscreen washers
− −
*
*
On vehicles with automatic
intermittent wipers, see page
138
06/12/06 10:47:03 32SMR600_141
Windscreen Wipers and Washers
When the system senses rainfall, it turns on the windscreen wipers and varies their speed (intermittent, low speed, or high speed) depending on how hard it is raining. This function is available when the vehicle speed exceeds 10 km/h (6 mph).
When the wiper lever is in the ‘‘LO’’ (low speed) or ‘‘HI’’ (high speed) position, the windscreen wipers run at that speed. Automatic sensing is disabled.
AUTO SENSITIVE RING
You can adjust the sensitivity of the system by turning the AUTO sensitive ring on the wiper lever.
AutomaticIntermittentWipers Onsomemodels
The automatic intermittent wiper system senses rainfall and automatically turns on the windscreen wipers. To enable sensing, push the lever down to select AUTO.
138
Instruments and Controls
06/12/06 10:47:07 32SMR600_142
Windscreen Wipers and Washers
RAINFALL SENSOR
Do not position the wiper lever in AUTO when driving through a car wash. Turn off this system when not in use.
The rainfall sensor is located in the windscreen near the rearview mirror. If the sensor is covered with mud, oil, dust, etc., the wipers may not operate properly or may operate unexpectedly.
Instruments and Controls 139
06/12/06 10:47:15 32SMR600_143
Turn Signals and Headlights
1. 2. 3. 4. 5. 6. 7.
Turn signal Off Position and indicator lights AUTO (on some models) Headlights on High beams Flash high beams
140
Instruments and Controls
−
Turn Signal Push down or up on the lever to signal a turn. To signal a lane change, push lightly on the lever in the proper direction and hold it. The lever will return to centre when you release it or complete a turn.
One-pushTurnSignal To signal a lane change easily, push the turn signal lever in the proper direction lightly and release it. The left or right turn signal indicator on the instrument panel and the appropriate outside turn signals will blink three times.
If you hold the turn signal lever, the turn signal continues to blink and will stop when you release it.
−
Turning the ’’ position turns
Headlights On switch to the ‘‘ on the position lights, tail-lights, instrument panel lights, and rear licence plate lights.
Turning the switch to the ‘‘ ’’ position turns on the headlights. If you leave the lights on with the key removed from the ignition switch, you will hear a reminder chime when you open the driver’s door.
’’ or the ‘‘
When the light switch is in the ‘‘ lights on indicator comes on as a reminder.
’’ position, the
You will also see the symbol ‘‘ or this symbol with a ‘‘HEADLIGHTS ON’’ message on the multi-information display.
,’’
06/12/06 10:47:25 32SMR600_144
−
Push the lever
High Beams forward until you hear a click to turn on the high beams. The blue high beam indicator will come on (see page ). Pull the lever back to return to the low beams.
82
To flash the high beams, pull the lever back lightly, then release it. The high beams will stay on as long as you hold the lever back.
Daytime Running Lights (For some types) The daytime running lights come on automatically when you turn the ignition switch to the ON (II) position. They go out automatically when the light switch is ON.
Headlights
−
Onsomemodels AUTO The automatic lighting feature turns on the headlights, all other exterior lights, and the instrument panel lights when it senses low ambient light.
To turn on the automatic lighting, turn the light switch to AUTO at any time. The lights will come on automatically when the outside light level becomes low (at dusk, for example). The lights on indicator comes on as a reminder. The lights and indicator turn off automatically when the system senses high ambient light.
The lights turn off automatically when you turn the ignition switch to the LOCK (0) position. To turn them on again, either turn the ignition switch to the ON (II) position, or turn the light switch to
position.
Even with the automatic lighting feature turned on, we recommend that you turn on the lights manually when driving at night or in a dense fog, or when you enter dark areas such as long tunnels or parking facilities.
Do not leave the light switch in AUTO if you will not be driving the vehicle for an extended period (a week or more). You should also turn off the lights if you plan to leave the engine idling or the engine off for a long time.
,’’ or the symbol with a
If there is a problem with the control system, you will see the symbol ‘‘ ‘‘CHECK SYSTEM’’ message on the multi-information display. Have the vehicle checked by your dealer as soon as possible.
CONTINUED
Instruments and Controls 141
06/12/06 10:47:34 32SMR600_145
Headlights, Front and Rear Fog Lights
LIGHTING SENSOR
Rear Fog Light (For some types)
To operate the rear fog light, turn the switch up from the off ( position. The instrument panel comes on to indicate that the rear fog light is on.
indicator in the
You can turn off the rear fog light with the headlights on by turning the switch up again.
The rear fog light will go off when you turn the headlights off. To turn the rear fog light on again, you have to turn the rear fog light switch again with the headlights on.
The automatic lighting feature is controlled by a sensor located on the windscreen near the rearview mirror. Do not cover this sensor or spill liquids on it.
REAR FOG LIGHT SWITCH
The rear fog light switch is located next to the light control switch. You can use the rear fog light when the headlights are on (the light control switch is in the
position).
142
Instruments and Controls
06/12/06 10:47:45 32SMR600_146
Front and Rear Fog Lights (For some types)
To turn on the rear fog light only, turn the switch down from the off indicator in the instrument panel comes on to indicate that the rear fog light is on.
) position. The
The front and rear fog lights will go off when you turn the light control switch off. With only the rear fog light on, it will go off when you turn the headlights off.
Front and Rear Fog Lights
FRONT AND REAR FOG LIGHT SWITCH
The fog light switch is located next to the light control switch. You can control the front fog lights with this switch when the light control switch is in the
position.
or
You can also use the rear fog light when the light control switch is in the lights are turned on.
position or the front fog
You can turn off the rear fog light with the headlights on by turning the switch down again.
To operate the front fog lights, turn the switch up from the off ( position to the
position. The
indicator comes on as a
reminder. To turn the rear fog light on with the front fog lights, turn the switch one position up from the
position.
You can turn off the rear fog light with the front fog lights on by turning the switch up again.
When you turn the light control switch on again, the front fog lights will also turn on. To turn the fog lights completely off, turn the fog light switch down to the off ( position.
To turn the rear fog light on again, you have to turn the fog light switch again with the headlights on lights on.
position) or the front fog
Instruments and Controls 143
06/12/06 10:47:52 32SMR600_147
Instrument Panel Brightness
To reduce glare at night, the instrument panel illumination dims when you turn the light switch to the
or
position.
The knob on the instrument panel adjusts the brightness of the instru- ment panel. Push on the knob to pop it out, then turn it to adjust the brightness.
Push the knob back in to prevent your setting from accidentally changing.
BRIGHTNESS LEVELS
The brightness can be shown within the six brightness levels on the multi-information display. When you turn the knob, the lower segment of the display changes to vertical bars that show you the current level. You will hear a tone when you reach the maximum or minimum brightness. The brightness level goes out about 5 seconds after you stop adjusting.
144
Instruments and Controls
You can adjust the brightness to the desired level with the headlight switch off, and also with the headlight switch on. Both settings will remain at those levels until you change them.
Each display (upper and lower) will illuminate with reduced brightness when you unlock and open the driver’s door, then go to normal brightness when you turn the ignition switch to the ON (II) position.
If you insert the key but do not turn the ignition switch to the ON (II) position, the illumination turns off after about 10 seconds.
06/12/06 10:48:01 32SMR600_148
Hazard Warning Button, Rear Window Demister
Hazard Warning Button
Rear Window Demister
Make sure the rear window is clear and you have good visibility before starting to drive.
The demister and antenna wires on the inside of the rear window can be accidentally damaged. When cleaning the glass, always wipe side- to-side.
Pushing the demister also turns the mirror heaters on and off. For more information, see page
173
Push the red button to turn on the hazard warning lights (four-way flashers). This causes all outside turn signals and both turn indicators in the instrument panel to flash. Use these lights to give a warning to other road users that your vehicle is causing a hazard.
The rear window demister will clear fog, frost, and thin ice from the window. Turn the ignition switch to the ON (II) position. Push the demister button to turn it on and off. The indicator in the button comes on to show the demister is on. It also shuts off when you turn off the ignition switch. You have to turn the demister on again when you restart the vehicle.
Instruments and Controls 145
06/12/06 10:48:09 32SMR600_149
Headlight Adjuster
The vertical angle of the headlights (low beam) can be adjusted according to the number of persons and the loading weight in the luggage area.
Push the knob to pop it out, then turn the knob to select an appropriate angle of the headlights. After adjusting, push the knob back in to prevent your setting from accidentally changing.
146
Instruments and Controls
0:
1:
2:
3:
A driver or a driver and passenger in the front seat. Five or four (Type-R model) persons in the front and rear seats. Five or four (Type-R model) persons in the front and rear seats and luggage in the luggage area, within the limits of maximum permissible axle weight and maximum permissible vehicle weight. A driver and luggage in the luggage area, within the limits of maximum permissible axle weight and maximum permissible vehicle weight.
(Forsometypes) Onvehicleswithheadlightsbulbsof highvoltagedischargetube Your vehicle is equipped with an automatic headlight adjusting system that senses changes in the vehicle posture due to riding and loading conditions of the passengers and their luggage and adjusts the vertical angle of the headlights (low beam) automatically.
06/12/06 10:48:16 32SMR600_150
Make any steering wheel adjustments before you start driving.
Adjusting the steering wheel position while driving may cause you to lose control of the vehicle and be seriously injured in a crash.
Adjust the steering wheel only when the vehicle is stopped.
Steering Wheel Adjustments
3.
Push the lever up to lock the steering wheel in position.
4.
Make sure you have securely locked the steering wheel in place by trying to move it up, down, in, and out.
Instruments and Controls 147
LEVER
1.
Push the lever under the steering column all the way down.
2.
Move the steering wheel up or down, and in or out, so it points toward your chest, not toward your face. Make sure you can see the instrument panel gauges and indicators.
06/12/06 10:48:24 32SMR600_151
Keys and Locks
KEY NUMBER TAG
IGNITION KEYS WITH REMOTE TRANSMITTER
You should have received a key number tag with your keys. You will need this key number if you ever have to get a lost key replaced. Use only Honda-approved key blanks.
These keys contain electronic circuits that are activated by the immobilizer system. They will not work to start the engine if the circuits are damaged.
RemoteTransmitter
Your two ignition keys are also fitted
with remote transmitters; see page
154
operation.
for an explanation of the
Protect the keys from direct sunlight, high temperature, and high humidity.
Do not drop the keys or set heavy objects on them.
Keep the keys away from liquids. If they get wet, dry them immediately with a soft cloth.
Two ignition keys come with your vehicle. You should keep one of them in a safe place, away from the vehicle, as a spare. They fit all the locks on your vehicle.
148
Instruments and Controls
06/12/06 10:48:34 32SMR600_152
Immobilizer System, Ignition Switch
Immobilizer System The immobilizer system protects your vehicle from theft. If an improperly-coded key (or other device) is used, the engine’s fuel system is disabled.
When you turn the ignition switch to the ON (II) position, the immobilizer system indicator should come on briefly, then go off. If the indicator starts to blink, it means the system does not recognize the coding of the key. Turn the ignition switch to the LOCK (0) position, remove the key, reinsert it, and turn the ignition switch to the ON (II) position again.
The system may not recognize your key’s coding if another immobilizer key or other metal object (i.e. key fob) is near the ignition switch when you insert the key.
If the system repeatedly does not recognize the coding of your key, contact your dealer.
Do not attempt to alter this system or add other devices to it. Electrical problems could result that may make your vehicle undrivable.
If you have lost your key and cannot start your engine, contact your dealer.
(EU models) EC Directives This immobilizer system complies with the R & TTE (Radio equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity) Directives.
Ignition Switch
The ignition switch has three positions: LOCK (0), ACCESSORY (I), and ON (II).
−
You can insert or
LOCK (0) remove the key only in this position. To turn the key, push it in slightly.
CONTINUED
Instruments and Controls 149
06/12/06 10:48:43 32SMR600_153
Ignition Switch
If the front wheels are turned, the anti-theft lock may make it difficult to turn the key. Firmly turn the steering wheel to the left or right as you turn the key.
−
You can
ACCESSORY (I) operate the audio system (on some types) and the cigarette lighter in this position.
The engine can be started with the
key in this position by pressing the
ENGINE START button (see page
on petrol models with manual
318
transmission, page
models with i-SHIFT, and page
320
on diesel models).
on petrol
319
−
This is the normal key
ON (II) position when driving. Several of the indicators on the instrument panel come on as a test when you turn the ignition switch from the ACCESSORY (I) to the ON (II) position.
On some types, the headlights come on automatically in this position.
150
Instruments and Controls
You will hear a reminder beeper if you leave the key in the ignition switch in the LOCK (0) or the ACCESSORY (I) position and open the driver’s door. You will also see the symbol ‘‘ ,’’ or the symbol with an ‘‘IGNITION KEY’’ message on the multi-information display. Remove the key to turn off the beeper and the warning symbol.
Removing the key from the ignition switch while driving locks the steering. This can cause you to lose control of the vehicle.
Remove the key from the ignition switch only when parked.
06/12/06 10:48:53 32SMR600_154
Both doors and the tailgate lock or unlock when you use the key to lock or unlock the driver’s door.
Onsometypes Pushing the bottom of the master door lock switch will unlock all doors and the tailgate.
Only the driver’s door unlocks when you use the driver’s door lock tab.
To unlock the driver’s door from the outside, turn the key and release it. If you turn it again, all doors and the tailgate unlock.
Power Door Locks
MASTER DOOR LOCK SWITCH
Lock
Unlock
To lock the doors and the tailgate, push the top of the master door lock switch on the driver’s door, pull the lock tab rearward on the driver’s door, or use the key on the outside lock on the driver’s door.
Pushing the bottom of the master door lock switch or pushing forward the lock tab on the driver’s door will unlock both doors and the tailgate.
Door Locks
RED INDICATOR
Unlock
Lock
Each door has a lock tab next to the inner door handle. Pushing forward or rearward the lock tab on each passenger’s door only locks and unlocks that door.
When the door is unlocked, you can see the red indicator on the lock tab next to the inner door handle.
CONTINUED
Instruments and Controls 151
06/12/06 10:48:59 32SMR600_155
Door Locks
To lock the passenger’s door when getting out of the vehicle, pull the lock tab rearward and close the door. To lock the driver’s door, remove the key from the ignition switch, pull and hold the outside door handle, and pull the lock tab rearward or push the top of the master door lock switch, then close the door.
LockoutPrevention With the driver’s door open and the key in the ignition, the master door lock switch is disabled. It is not disabled if the driver’s door is closed. If you try to lock an open driver’s door by pulling the lock tab rearward with the outside handle pulled, the tabs on all doors pop out.
Onvehicleswithsecuritysystem When you lock the doors and the tailgate with the key or the remote transmitter, all outside turn signals and both indicators in the instrument panel flash three times to verify the doors and the tailgate are locked and the security system has set (see page
273
).
The security system activates after you lock the doors and the tailgate with the lock tab on the driver’s door or the master door lock switch (see page
273
).
152
Instruments and Controls
06/12/06 10:49:08 32SMR600_156
SuperLocking (Forsometypes)
The super locking will not set if either door or the tailgate is not fully closed. It will be set even if the bonnet, or either window is open.
With the super locking set, the master door lock switch on the driver’s door and the lock tabs on both doors are disabled.
You can also set the super locking with the remote transmitter. To set it, push the LOCK button twice within 5 seconds (see page
155
).
The super locking helps to protect your vehicle and valuables from theft. To set the super locking, turn the key towards the front of the vehicle twice within 5 seconds.
To cancel the super locking, unlock the driver’s door with the key or the remote transmitter.
Onvehicleswithultrasonicsensor Only the remote transmitter can reset the security system. Unlocking the driver’s door with the key activates the alarm.
Door Locks
If there are persons inside the vehicle with the super locking set, they cannot unlock the doors from the inside.
Make sure there is no person inside the vehicle before setting the super locking.
Onvehicleswithultrasonicsensor If you set the super locking with the windows open, the ultrasonic sensor may activate the alarm unexpectedly when the system senses strong vibrations on the vehicle or loud sound.
Instruments and Controls 153
06/12/06 10:49:16 32SMR600_157
Remote Transmitter
LED
LOCK BUTTON
UNLOCK BUTTON
−
LOCK Press this button to lock both doors and the tailgate. When you push the LOCK button, all outside turn signals and both indicators in the instrument panel flash three times to verify the doors and the tailgate are locked and the security system (if equipped) has set. You cannot lock the doors and the tailgate if either door or the tailgate is not fully closed or the key is in the ignition switch.
154
Instruments and Controls
−
UNLOCK Press this button to unlock both doors and the tailgate. When you push the UNLOCK button, all outside turn signals, and both indicators in the instrument panel flash once.
Onsometypes Press this button once to unlock the driver’s door. Push it twice to unlock the remaining doors and the tailgate.
The front ceiling light (if the light
switch is in the Door position) and
rear ceiling light (if the light switch
is in the centre position) will come
on when you press the UNLOCK
button. If you do not open either
door or the tailgate within 30
seconds, the lights fade out. If you
relock the doors and tailgate with
the remote transmitter before 30
seconds have elapsed, the lights will
go off immediately.
If you do not open either door or the tailgate within 30 seconds, the doors and the tailgate automatically relock and the security system (if equipped) sets.
You cannot unlock the doors and the tailgate if the key is in the ignition switch.
06/12/06 10:49:25 32SMR600_158
SuperLocking (Forsometypes) You can set the super locking with the remote transmitter. To set the super locking, push the LOCK button twice within 5 seconds.
The super locking will not set if either door or the tailgate is not fully closed. It will be set even if the bonnet, or either window is open.
To cancel the super locking, push the UNLOCK button on the remote transmitter, or unlock the driver’s door with the key.
See page
153
super locking.
for information on the
If there are persons inside the vehicle with the super locking set, they cannot unlock the doors from the inside.
Make sure there is no person inside the vehicle before setting the super locking.
Remote Transmitter
Remote Transmitter Care
Avoid dropping or throwing the transmitter.
Protect the transmitter from extreme temperature.
Do not immerse the transmitter in any liquid.
If you lose a transmitter, the replacement needs to be reprogrammed by your dealer.
Instruments and Controls 155
06/12/06 10:49:34 32SMR600_159
Remote Transmitter
Replacing the Transmitter Battery If it takes several pushes on the button to lock or unlock the doors and the tailgate, replace the battery as soon as possible.
Battery type: CR1616
156
Instruments and Controls
BATTERY
SCREW
TAB
To replace the battery:
1.
2.
Remove the screw at the base of the transmitter with a small Phillips-head screwdriver.
Separate the transmitter by prying its middle seam with your fingernail.
3.
Inside the transmitter, separate the inner cover from the keypad by releasing the two tabs on the cover.
06/12/06 10:49:40 32SMR600_160
4.
Remove the old battery from the back of the inner cover, and insert a new battery into the back of the cover with the
side facing down.
+
5.
Install the parts in reverse order.
An improperly disposed of battery can hurt the environment. Always confirm local regulations for battery disposal.
Remote Transmitter
(EU models) EC Directives This keyless entry system complies with the R & TTE (Radio equipment and Telecommunications Terminal Equipment and the mutual recognition of their conformity) Directives.
Instruments and Controls 157
06/12/06 10:49:46 32SMR600_161
Tailgate
The tailgate will lock or unlock when you lock or unlock the driver’s door with the key, the remote transmitter, the master door lock switch, or the lock tab on the driver’s door.
RELEASE
HANDLE
To open the tailgate, push the release, then lift up. To close the tailgate, use the inner handle to pull it down, then press down on the back edge.
Keep the tailgate closed at all times
while driving to avoid damaging the
tailgate and to prevent exhaust gas
from getting into the interior. See
Carbon Monoxide Hazard
.65
on page
158
Instruments and Controls
06/12/06 10:49:53 32SMR600_162
Opening the Tailgate Manually
Lock
Tailgate
COVER
Unlock (open)
If the power door lock system cannot unlock the tailgate, unlock it manually. In this case, you cannot open the tailgate with the release.
To open the tailgate, access the tailgate release lever from inside the vehicle. Place a cloth on the edge of the cover, then use a small flat-tipped screwdriver to remove the cover on the back of the tailgate.
Push the release lever to the lower right as shown.
If you need to open the tailgate manually, it means there is a problem with the tailgate. Have the vehicle checked by your dealer.
Instruments and Controls 159
06/12/06 10:50:01 32SMR600_163
Seats
−
15 16
Front Seat Adjustments Seepages forimportantsafety informationandwarningsabouthowto properlypositiontheseatsandseat- backs.
Make all seat adjustments before you start driving.
160
Instruments and Controls
SEAT-BACK ANGLE ADJUSTMENT LEVER
Driver’s seat is shown.
To adjust the seat forward or backward, pull up on the bar under the seat cushion’s front edge. Move the seat to the desired position, and release the bar. Try to move the seat to make sure it is locked in position.
To change the seat-back angle, pull up on the lever on the outside of the seat cushion.
Once a seat is adjusted correctly, rock it back and forth to make sure it is locked in position.
06/12/06 10:50:07 32SMR600_164
Rear Seat Access
Driver’s side
Passenger’s side
RELEASE LEVER
Seats
RELEASE LEVER