Login- Download PDF Manual
-
protect child
properly
If you have children, or ever need to drive with a child in your vehicle, be sure to read this section. It begins with important general guidelines, then presents special information for infants, small children, and larger children.
34
Driver and Passenger Safety
06/12/06 10:33:20 32SMR600_038
Protecting Children General Guidelines
−
In most countries, child restraint systems must meet the specifications of the ECE 44
regulation.In many countries, the law requires children younger than 12 years of age and less than 150 cm (60 in) in height to be secured in an officially approved and suitable child restraint system. In those countries, officially approved and suitable child restraint systems must therefore be used in order to transport a child on any passenger seat whatsoever. Please check your local legal requirements.
All Children Should Sit in a Back Seat According to crash statistics, children of all ages and sizes are safer when they are restrained in a back seat. It is recommended that all children age 12 and under be properly restrained in a back seat.
Children who ride in back are less likely to be injured by striking interior vehicle parts during a collision or hard braking. Also, children cannot be injured by an inflating airbag when they ride in the back.
The Passenger’s Front Airbag Poses Serious Risks Front airbags have been designed to help protect adults in a moderate to severe frontal collision. To do this, the passenger’s front airbag is quite large, and it can inflate with enough force to cause very serious injuries.
Infants Neverputarearwardfacingchild restraintsysteminthefrontseatofa vehicleequippedwithapassenger’s If the airbag inflates, it frontairbag. can hit the back of the child restraint system with enough force to kill or very seriously injure an infant.
CONTINUED
Driver and Passenger Safety
35
06/12/06 10:33:27 32SMR600_039
Protecting Children General Guidelines
−
If the passenger’s front airbag inflates, it can hit the rearward facing child restraint system with great force. The rearward facing child restraint system can be dislodged or struck with enough force to cause very serious injury to the infant.
Small Children Placingafrontfacingchildrestraint systeminthefrontseatofavehicle equippedwithapassenger’sfront airbagcanbehazardous. vehicle seat is too far forward, or the child’s head is thrown forward during a collision, an inflating front airbag can strike the child with enough force to kill or very seriously injure a small child.
If the
Larger Children Childrenwhohaveoutgrownchild restraintsystemsarealsoatriskof beinginjuredorkilledbyaninflating Whenever passenger’sfrontairbag. possible, larger children should sit in the back seat, in a booster seat if needed, and be properly restrained with a seat belt (see page 60
important information about protecting larger children).for
In all cases observe the legal requirements of the countries in which you will drive.
As required by E.C.E Regulation No. 94;
DO NOT place rear-facing child seat on this seat with airbag.
DEATH OR SERIOUS INJURY can occur.
36
Driver and Passenger Safety
06/12/06 10:33:34 32SMR600_040
To remind you of the passenger’s front airbag hazards, and that children must be properly restrained in a back seat, your vehicle has warning labels on the windscreen, on the front passenger’s doorjamb and on the front visors. Please read and follow the instructions on these labels.
Protecting Children General Guidelines
−
As required by E.C.E Regulation No. 94;
Extreme Hazard!
DO NOT use a rearward facing child restraint on a seat protected by an airbag in front of it!
DO NOT place rear-facing child seat on this seat with airbag.
DEATH OR SERIOUS INJURY can occur.
Driver and Passenger Safety
37
06/12/06 10:33:39 32SMR600_041
Protecting Children General Guidelines
−
The Side Airbag Poses Serious Risks Side airbags have been designed to help protect adults in a moderate to severe side impact. If any part of a child’s body is in the path of a deploying airbag, an inflating side airbag can strike the child with enough force to kill or very seriously injure a child.
To remind you of the side airbags hazards, and that children must be properly restrained in the back seat, your vehicle has the safety label on each front doorjamb.
Leaning over the front door can result in serious injury or death if the side airbag inflates.
Always sit upright with their back against the seat-back.
38
Driver and Passenger Safety
06/12/06 10:33:50 32SMR600_042
If You Must Drive with Several Children Your vehicle has a back seat where children can be properly restrained. If you ever have to carry a group of children, and a child must ride in front:
Place the largest child in the front seat, provided the child is large enough to wear the lap/shoulder belt properly (see page
60
).
Move the vehicle seat as far to the rear as possible (see page
160
).
Have the child sit upright and well back in the seat (see page
19
).
Make sure the seat belt is properly positioned and secured (see page 17
).
Protecting Children General Guidelines
−
If a Child Requires Close Attention Many parents say they prefer to put an infant or a small child in the front passenger seat so they can watch the child, or because the child requires attention.
Placing a child in the front seat exposes the child to hazards in a frontal collision or a side impact, and paying close attention to a child distracts the driver from the important tasks of driving, placing both of you at risk.
If a child requires close physical attention or frequent visual contact, we strongly recommend that another adult ride with the child in the back seat. The back seat is far safer for a child than the front.
Additional Safety Precautions
Neverholdaninfantorchildon If you are not wearing a yourlap. seat belt in crash, you could be thrown forward and crush the child against the dashboard or a seat-back. If you are wearing a seat belt, the child can be torn from your arms and be seriously hurt or killed.
Neverputaseatbeltoveryourself andachild. belt could press deep into the child and cause serious or fatal injuries.
During a crash, the
Neverlettwochildrenusethe If they do, they sameseatbelt. could be very seriously injured in a crash.
CONTINUED
Driver and Passenger Safety
39
06/12/06 10:33:58 32SMR600_043
Protecting Children General Guidelines
−
Donotleavechildrenaloneina Leaving children without vehicle. adult supervision is illegal in some countries, and can be very hazardous.
For example, infants and small children left in a vehicle on a hot day can die from heatstroke. A child left alone with the key in the ignition switch can accidentally set the vehicle in motion, possibly injuring themselves or others.
Lockbothdoorsandthetailgate whenyourvehicleisnotinuse. Children who play in vehicles can accidentally get trapped inside the vehicle. Teach your children not to play in or around vehicles.
Even very young
Keepvehiclekeys/remote transmittersoutofthereachof children. children learn how to unlock vehicle doors, turn on the ignition switch, and open the tailgate, which can lead to accidental injury or death.
WARNING: Alwaystaketheignition keywithyouwheneveryouleavethe vehiclealone(withotheroccupants).
‘‘Never let children kneel on seats or stand while the vehicle is in motion. The violent forces created during emergency braking will cause the children to be thrown forward. The children could be seriously injured or killed.’’
Makesureanyunusedseatbelt thatachildcanreachisbuckled, thelockableretractorisactivated, andthebeltisfullyretractedand locked. seat belt around their neck, they can be seriously or fatally injured. (See pages activate and deactivate the lockable retractor.)
If a child wraps a loose
for how to
and
52
56
WARNING: Usethemainpower windowswitchtopreventchildren fromopeningthewindows.Usingthis featurewillpreventchildrenfrom playingwiththewindows,which couldexposethemtohazardsor distractthedriver(seepage ).168
40
Driver and Passenger Safety
06/12/06 10:34:08 32SMR600_044
Protecting Infants
ChildRestraintSystemType An infant must be properly restrained in a rear-facing, reclining child restraint system until the child reaches the restraint system maker’s weight or height limit for the restraint system, and the child is at least one year old.
Protecting Infants and Small Children
Only a rearward facing child restraint system provides proper support for a baby’s head, neck and back.
Two types of restraints may be used: a restraint system designed exclusively for infants, or a convertible restraint system used in the rearward facing, reclining mode.
For EU countries, refer to page for the recommended child 47
restraint system.Donotputarearwardfacingchild restraintsysteminaforward-facing If placed facing forward, an position. infant could be very seriously injured during a frontal collision.
RearwardFacingChildRestraint SystemPlacement A rearward facing child restraint system can be placed in any seating position in the back seat, but not in the front. facingchildrestraintsysteminthe frontseat.
Neverputarearward
For EU countries, an approved rearward facing child restraint system should be placed in any seating position in the back seat (see page
47
).
If the passenger’s front airbag inflates, it can hit the back of the restraint with enough force to kill or seriously injure an infant.
CONTINUED
Driver and Passenger Safety
41
06/12/06 10:34:15 32SMR600_045
Protecting Infants and Small Children
When properly installed, a rearward facing child restraint system may prevent the driver or a front passenger from moving their seat as far back as recommended, or from locking their seat-back in the desired position.
In either situation, we strongly recommend that you install the child restraint system directly behind the front passenger seat, move the seat as far forward as needed, and leave it unoccupied. Or you may wish to get a smaller rearward facing child restraint system.
Placing a rearward facing child restraint system in the front seat can result in serious injury or death during a collision.
Always place a rearward facing child restraint system in the back seat, not the front.
42
Driver and Passenger Safety
As required by E.C.E Regulation No. 94;
DO NOT place rear-facing child seat on this seat with airbag.
DEATH OR SERIOUS INJURY can occur.
If the passenger’s front airbag inflates, it can hit the rearward facing child restraint system with great force. The rearward facing child restraint system can be dislodged or struck with enough force to cause very serious injury to the infant.
06/12/06 10:34:25 32SMR600_046
Protecting Small Children
ChildRestraintSystemType A child who is at least one year old, and who fits within the child restraint system maker’s weight and height limits, should be restrained in a front facing, upright child restraint system.
Of the different restraint systems available, we recommend those that have a five-point harness system as shown.
Protecting Infants and Small Children
We also recommend that a small child uses the child restraint system as long as possible, until the child reaches the weight or height limit for the restraint system.
For EU countries, refer to page for the recommended child 47
restraint system.ChildRestraintSystemPlacement We strongly recommend placing a front facing child restraint system in a back seat, not the front.
Placingafrontfacingchildrestraint systeminthefrontseatofavehicle equippedwithapassenger’sairbag If the vehicle seat canbehazardous. is too far forward, or the child’s head is thrown forward during a collision, an inflating airbag can strike the child with enough force to cause very serious or fatal injuries.
If it is necessary to put a front facing child restraint system in the front, move the vehicle seat as far to the rear as possible, and be sure the child restraint system is firmly secured to the vehicle and the child is properly strapped in the restraint system.
Placing a front facing child restraint system in the front seat can result in serious injury or death if the front airbag inflates.
If you must place a front facing child restraint system in front, move the vehicle seat as far back as possible, and properly restrain the child.
CONTINUED
Driver and Passenger Safety
43
06/12/06 10:34:33 32SMR600_047
Selecting a Child Restraint System
We also recommend selecting a lower anchorages system-compatible child restraint system with a rigid, rather than a flexible, anchor (see page
49
).
In EU countries, a child restraint system with a flexible anchor is not available.
In seating positions and vehicles not equipped with lower anchorages, a lower anchorages system-compatible child restraint system can be installed using a seat belt.
Whatever type of child restraint you choose, to provide proper protection, a child restraint system should meet three requirements:
1.
In most
Thechildrestraintsystemshould meetsafetystandards. countries, child restraint systems must meet the specifications of the ECE 44 regulation. Look for the approval mark on the system and the manufacturer’s statement of compliance on the box.
The manufacturer of the vehicle does not assume any responsibility for damage which would be caused by a defect inherent in the recommended child restraint system.
When buying a child restraint system, you need to choose either a conventional child restraint system, or one designed for use with the lower anchorages and tethers.
Conventional child restraint systems must be secured to a vehicle with a seat belt, whereas lower anchorages system-compatible child restraint systems are secured by attaching the restraint to hardware built into the two outer seating positions in the back seat.
Since lower anchorages system- compatible child restraint systems are easier to install and reduce the possibility of improper installation, if your vehicle is equipped with the lower anchorages system, we recommend selecting this style.
44
Driver and Passenger Safety
06/12/06 10:34:39 32SMR600_048
Selecting a Child Restraint System
3.
Thechildrestraintsystemshould fitthevehicleseatingposition(or positions)whereitwillbeused.
2.
Thechildrestraintsystemshould beofthepropertypeandsizetofit thechild. Rearward facing for infants, front facing for small children.
Make sure the restraint system fits your child. Check the manufacturer’s instructions and labels for height and weight limits.
Before purchasing a conventional child restraint system, or using a previously purchased one, we recommend that you test the restraint system in the specific vehicle seating position or positions where the child restraint system will be used.
For EU countries, refer to page 47
for the recommended child restraint system.Driver and Passenger Safety
45
06/12/06 10:34:47 32SMR600_049
Installing a Child Restraint System
After selecting a proper child restraint system and a good place to install the restraint system, there are three main steps in installing the restraint system:
1.
All child
Properlysecurethechildrestraint systemtothevehicle. restraint systems must be secured to the vehicle with the lap part of a lap/shoulder belt or with the lower anchorages system. A child whose restraint system is not properly secured to the vehicle can be endangered in a crash.
ExceptforEuropeanmodels If you use a lap/shoulder belt without an additional lockable retractor, be sure you install a locking clip on the seat belt (see page
57
).
2.
Makesurethechildrestraint After systemisfirmlysecured. installing a child restraint system, push and pull the restraint system forward and from side-to-side to verify that it is secure.
A child restraint system secured with a seat belt should be installed as firmly as possible. However, it does not need to be ‘‘rock solid.’’ Some side-to-side movement can be expected and should not reduce the child restraint system’s effectiveness.
If the child restraint system is not secure, try installing it in a different seating position, or use a different style of child restraint system that can be firmly secured.
For EU countries, refer to page for the recommended child 47
restraint system.3.
Securethechildinthechild Make sure the restraintsystem. child is properly strapped in the child restraint system according to the child restraint system maker’s instructions. A child who is not properly secured in a child restraint system can be seriously injured in a crash.
The following pages provide the recommended child restraint systems for EU countries and guidelines on how to properly install a child restraint system. A front facing child restraint system is used in all examples, but the instructions are the same for a rearward facing child restraint system.
46
Driver and Passenger Safety
06/12/06 10:35:00 32SMR600_050
Installing a Child Restraint System
Child Restraint System for EU Countries Various types of child restraint systems are available. Not all types are suitable for your vehicle. Please refer to the table below to select which category of child restraint system can be used on each seating position.
Mass Group
Front passenger
Rear passenger
Seating Position
group 0
group 0＋
Up to 10 kg Up to 13 kg
Outboard
IL (Honda BABY-SAFE
ISO FIX) or U
Centre
＊
Honda BABY-SAFE Honda BABY-SAFE
group I
9 kg to 18 kg
Honda LORD
＊
IUF (Size class A, B1, B)
Honda LOAD
15 kg to 25 kg 22 kg to 36 kg
Honda KID Honda KID
＊
＊
or U
Honda KID Honda KID
Suitable for particular ISO FIX child restraint systems (CRS) given in this table. Suitable for front facing ISO FIX child restraint systems of universal category approved for use in this mass group. Suitable for ‘‘universal’’ category child restraints approved for use in this mass group. Seat position not suitable for children in this mass group. Move the front seat to its rearmost position.
1: 2: Except for Type-R
group II group III IL: IUF:
U: X: ＊ ＊
A size class is specified for some child restraint systems. Make sure to check the size class as indicated on the manufacturer’s instructions, package, and labels of the child restraint.
The particular child restraints in the above table are Honda Genuine Parts. They are available from your dealer. For a correct installation, please refer to the Child Restraint Instruction Manual.
Driver and Passenger Safety
CONTINUED 47
06/12/06 10:35:04 32SMR600_051
Installing a Child Restraint System
The use of any child restraint system which is not suitable for your vehicles would not properly secure the infant or child who could therefore be killed or seriously injured.
Your vehicle is equipped with lower anchorages at the outer seating positions on the rear seat. These anchorages are only to be used with a child restraint system designed to be attached to the lower anchorages. Refer to page for how to install a child restraint system to the lower anchorages.
49
48
Driver and Passenger Safety
06/12/06 10:35:12 32SMR600_052
Installing a Child Restraint System with the Lower Anchorages Your vehicle is equipped with lower anchorages at the outer rear seats. These anchorages are located between the seat-back and seat bottom, and are to be used only with a child restraint system designed for use with the lower anchorages.
Installing a Child Restraint System
LOWER ANCHORAGES
The location of each lower anchorage is indicated by a small button above the anchorage point.
For EU countries, refer to page for the recommended child 47
restraint system.To install a child restraint system designed to be attached to the lower anchorages:
1.
2.
Move the seat belt buckle or tongue away from the lower anchorages.
Make sure there are no objects near the anchorages that could prevent a secure connection between the child restraint system and the anchorages.
CONTINUED
Driver and Passenger Safety
49
06/12/06 10:35:20 32SMR600_053
Installing a Child Restraint System
LOWER ANCHORAGE
Rigid type
GUIDE-CUP
GUIDE-CUP
3. Onsomechildrestraintsystems
You may use optional guide-cups that came with your child restraint system to install it to the lower anchorages without damaging the seat surface.
Attach the guide-cups to the lower anchorages as shown in the illustration.
When using the guide-cups, always follow the child restraint system manufacturer’s instructions.
4.
Place the child restraint system on the vehicle seat, then attach the child restraint system to the lower anchorages according to the child restraint system maker’s instructions.
Some child restraint systems designed for use with lower anchorages have a rigid-type connector as shown above.
50
Driver and Passenger Safety
06/12/06 10:35:28 32SMR600_054
Flexible type
Other child restraints have a flexible- type connector as shown above.
Installing a Child Restraint System
5.
Whatever type you have, follow the child restraint system maker’s instructions for adjusting or tightening the fit.
Flexible type child restraint system is available in some countries. In EU countries, this type is not available.
ATTACHING CLIP
Front
ANCHOR FITTING
6.
Attach the attaching clip to the anchor fitting as shown in the illustration. Make sure the strap is not twisted, then tighten the strap according to the child restraint system maker’s instructions.
The above illustration shows how the attaching clip should be routed in EU countries.
CONTINUED
Driver and Passenger Safety
51
06/12/06 10:35:35 32SMR600_055
Installing a Child Restraint System
7.
Push and pull the child restraint system forward and from side-to- side to verify that it is secure.
The design and suitability of the child restraint systems must be carefully checked with the child restraint system manufacturer concerned and the seller of those systems. If you are not sure, consult your dealer before purchasing this type of child restraint system.
Installing a Child Restraint System with a Lap/Shoulder Belt When not using the lower anchorages system, all child restraint systems must be secured to the vehicle with the lap part of a lap/ shoulder belt.
ATTACHING CLIP
Front
ANCHOR FITTING
Lift the head restraint (see page ), then route the tether strap 162
through the legs of the head restraint and over the seat-back, making sure the strap is not twisted.Attach the attaching clip to the anchor fitting, then tighten the strap as instructed by the child restraint system maker.
52
Driver and Passenger Safety
06/12/06 10:35:43 32SMR600_056
Installing a Child Restraint System
To properly route a lap/shoulder belt through a child restraint system, follow the restraint system maker’s instructions.
The procedures in the following pages are described based on a front facing child restraint system available in EU countries.
For EU countries, refer to page for installing a child restraint 47
system.LABEL
SEAT BELT
In addition, the lap/shoulder belts in the back seating positions have a lockable retractor that must be activated to secure a child restraint system.
The seat belt with a lockable retractor has a label as shown in the illustration above.
1.
Place the child restraint system in the desired back seating position. Make sure the child restraint is positioned well back in the seat- back.
If you place the child restraint system in either rear outer seating position and use the tether strap for additional security, make sure to push down the head restraint to the lowest position and attach the attaching clip to the anchor fitting before securing the child restraint system with the lap/shoulder belt.
CONTINUED
Driver and Passenger Safety
53
06/12/06 10:35:50 32SMR600_057
Installing a Child Restraint System
TAB
4.
5.
Push down the tab. Route the shoulder part of the belt into the slit at the side of the restraint, then let the belt feed back into the retractor.
After the belt has retracted, tug on it. If the belt is locked, you will not be able to pull it out. If you can pull the belt out, it is not locked, and you will need to repeat these steps.
2.
Route the belt through the restraint according to the restraint system maker’s instructions, then insert the latch plate into the buckle.
3.
To activate the lockable retractor, slowly pull the shoulder part of the belt all the way out until it stops.
54
Driver and Passenger Safety
06/12/06 10:35:55 32SMR600_058
Installing a Child Restraint System
To remove slack, it may help to put weight on the child restraint system, or push on the back of the restraint system while pulling up on the belt.
6.
After confirming that the belt is locked, grab the shoulder part of the belt near the buckle, and pull up to remove any slack from the lap part of the belt. Remember, if the lap part of the belt is not tight, the child restraint system will not be secure.
7.
Secure the belt in the slit by pushing up the tab. Make sure the belt is not twisted and it is positioned properly in the slit.
CONTINUED
Driver and Passenger Safety
55
06/12/06 10:36:02 32SMR600_059
Installing a Child Restraint System
To deactivate the lockable retractor and remove a child restraint system, unlatch the buckle, unroute the seat belt, and let the belt fully retract.
LOCKING CLIP
8.
Push and pull the child restraint system forward and from side-to- side to verify that it is secure enough to stay upright during normal driving manoeuvres. If the child restraint system is not secure, unlatch the belt, allow it to retract fully, then repeat these steps.
56
Driver and Passenger Safety
ExceptforEuropeanmodels Onvehicleswithoutlockableretractor fittedtotheseatwherethechildis positioned When you secure a child restraint system with a lap/shoulder belt, be sure you install a locking clip on the seat belt.
06/12/06 10:36:12 32SMR600_060
UsingaSeatBeltLockingClip ExceptforEuropeanmodels Onvehicleswithoutlockableretractor fittedtotheseatwherethechildis positioned Always use a seat belt locking clip when you secure a child restraint system to your vehicle with a lap/ shoulder belt. This helps prevent the restraint system from shifting position or overturning.
A locking clip is usually included with the child restraint system. If you need a clip, contact the seat’s manufacturer or a store that sells child restraints.
If it is necessary to put a front facing child restraint system in the front, move the vehicle seat as far to the rear as possible, be sure the child restraint system is firmly secured to the vehicle, and the child is properly strapped in the restraint system (see page
43
).
Installing a Child Restraint System
To install a locking clip, do the following:
1.
2.
3.
Place the child restraint in the seat with a lap/shoulder belt. Route the lap/shoulder belt through the restraint according to the seat manufacturer’s instructions.
Insert the latch plate into the buckle. Pull on the shoulder part of the belt to make sure there is no slack in the lap portion.
Tightly grasp the belt near the latch plate. Pinch both parts of the belt together so they won’t slip through the latch plate. Unbuckle the seat belt.
LOCKING CLIP
4.
5.
Install the locking clip as shown. Position the clip as close as possible to the latch plate.
Insert the latch plate into the buckle. Push and pull on the child restraint system to verify that it is held firmly in place. If it is not, repeat these steps until the restraint is secure.
Driver and Passenger Safety
57
06/12/06 10:36:20 32SMR600_061
Installing a Child Restraint System
Installing a Child Restraint System with a Tether Children riding in vehicles should be restrained to minimize the risk of injury in the event of an accident.
ANCHOR FITTING
Since a tether can provide additional security to the lap/shoulder belt installation, we recommend using a tether whenever one is required or available. (The owners may check with the child restraint system maker to determine whether a tether is available for a particular child restraint system.)
TETHER ANCHOR POINTS
A child restraint system with a tether can be installed in the two outer positions in the back seat, using one of the anchor points shown in the illustration.
58
Driver and Passenger Safety
UsinganAnchorFitting
ATTACHING CLIP
Front
TETHER STRAP
ANCHOR FITTING
1.
After properly securing the child restraint system (see page or ), route the tether strap over 52
the seat-back and on both sides of the head restraint as shown.49
The above illustration shows how the tether strap should be routed in EU countries.
06/12/06 10:36:29 32SMR600_062
ATTACHING CLIP
Front
Installing a Child Restraint System
2.
Lift the cover, then attach the attaching clip to the anchor fitting, making sure the strap is not twisted.
3.
Tighten the tether strap according to the child restraint system maker’s instructions.
Childrestraint
WARNING: anchoragesaredesignedtowithstand onlythoseloadsimposedbycorrectly fittedchildrestraints.Underno circumstancesaretheytobeusedfor adultseatbelts,harnessesorfor attachingotheritemsorequipmentto thevehicle.
To attach the tether to the child restraint system, follow the child restraint system maker’s instructions.
ANCHOR FITTING
Onsomemodels Lift the head restraint, then route the tether strap over the seat-back and through the head restraint legs.
When the child restraint system is used, follow the instructions that came with the child restraint system.
Driver and Passenger Safety
59
06/12/06 10:36:34 32SMR600_063
Protecting Larger Children
When a child reaches the recommended weight or height limit for a front facing child restraint system, the child should sit in a back seat on a booster seat and wear a lap/shoulder belt.
The following pages give instructions on how to check proper seat belt fit, what kind of booster seat to use if one is needed, and important precautions for a child who must sit in front.
60
Driver and Passenger Safety
Allowing a child age 12 or under to sit in front can result in injury or death if the passenger’s front airbag inflates.
If a child must ride in front, move the vehicle seat as far back as possible, use a booster seat if needed, have the child sit up properly and wear the seat belt properly.
Leaning over the front door can result in serious injury or death if the side airbag inflates.
Always sit upright with their back against the seat-back.
06/12/06 10:36:44 32SMR600_064
Checking Seat Belt Fit
To determine if a lap/shoulder belt properly fits a child, have the child put on the seat belt, then ask yourself:
1.
Does the child sit all the way back against the seat?
2.
Do the child’s knees bend comfortably over the edge of the seat?
3.
Does the shoulder belt cross between the child’s neck and arm?
4.
Is the lap part of the belt as low as possible, touching the child’s thighs?
5.
Will the child be able to stay seated like this for the whole trip?
If you answer yes to all these questions, the child is ready to wear the lap/shoulder belt correctly. If you answer no to any question, the child needs to ride on a booster seat.
Protecting Larger Children
Using a Booster Seat
A child who has outgrown a front facing child restraint system should ride in a back seat and use a booster seat until the lap/shoulder belt fits them properly without the booster.
CONTINUED
Driver and Passenger Safety
61
06/12/06 10:36:51 32SMR600_065
Protecting Larger Children
Booster seats can be high-back or low-back. Whichever style you select, make sure the booster seat meets approved safety standards (see page ) and that you follow the booster 44
seat maker’s instructions.If a child who uses a booster seat must ride in front, move the vehicle seat as far back as possible and be sure the child is wearing the seat belt properly.
A child may continue using a booster seat until the tops of their ears are even with the top of the vehicle’s or booster’s seat-back. A child of this height should be tall enough to use the lap/shoulder belt without a booster seat.
For EU countries, refer to page 47
for the booster seat placement.
GUIDE
A back-rest may be available for a specific booster seat. Install the back-rest to the booster seat and adjust it to the vehicle seat according to the booster seat maker’s instructions. Make sure the seat belt is properly routed through the guide at the shoulder of the back-rest and the belt does not touch and cross the child’s neck (see page
17
).
62
Driver and Passenger Safety
06/12/06 10:37:03 32SMR600_066
When Can a Larger Child Sit in Front It is recommended that all children age 12 and under be properly restrained in the back seat.
Of course, children vary widely. And while age may be one indicator of when a child can safely ride in front, there are other important factors you should consider.
The back seat is the safest place for a child of any age or size.
If the passenger’s front airbag inflates in a moderate to severe frontal collision, the airbag can cause serious injuries to a child who is unrestrained, improperly restrained, sitting too close to the airbag, or out of position.
If your vehicle is equipped with the side airbag, it also poses risks. If any part of a larger child’s body is in the path of a deploying side airbag, the child could receive possibly serious injuries.
PhysicalSize Physically, a child must be large enough for the lap/shoulder belt to properly fit (see pages ). If 60
the seat belt does not fit properly, with or without the child sitting on a booster seat, the child should not sit in front.and
17
Maturity To safely ride in front, a child must be able to follow the rules, including sitting properly, and wearing the seat belt properly throughout a ride.
Protecting Larger Children
If you decide that a child can safely ride up front, be sure to:
Carefully read the owner’s manual, and make sure you understand all seat belt instructions and all safety information.
Move the vehicle seat to the rear- most position.
Have the child sit up straight, back against the seat, and feet on or near the floor.
Check that the child’s seat belt is properly and securely positioned.
Remind the child not to lean toward the door.
Supervise the child. Even mature children sometimes need to be reminded to fasten the seat belts or sit properly.
Driver and Passenger Safety
63
Twochildrenshouldneverusethe sameseatbelt. could be very seriously injured in a crash.
If they do, they
Devices intended to
Donotputanyaccessoriesona seatbelt. improve a child’s comfort or reposition the shoulder part of a seat belt can make the belt less effective and increase the chance of serious injury in a crash.
06/12/06 10:37:09 32SMR600_067
Protecting Larger Children
Additional Safety Precautions
Donotletachildwearaseatbelt This could result acrosstheneck. in serious neck injuries during a crash.
This could
Donotletachildputtheshoulder partofaseatbeltbehindtheback orunderthearm. cause very serious injuries during a crash. It also increases the chance that the child will slide under the belt in a crash and be injured.
64
Driver and Passenger Safety
06/12/06 10:37:17 32SMR600_068
Your vehicle’s exhaust contains carbon monoxide gas. Carbon monoxide should not enter the vehicle in normal driving if you maintain your vehicle properly and follow the information on this page.
Have the exhaust system inspected for leaks whenever:
The vehicle is raised for an oil change.
You notice a change in the sound of the exhaust.
The vehicle was in an accident that may have damaged the underside.
Carbon monoxide gas is toxic. Breathing it can cause unconsciousness and even kill you.
Avoid any enclosed areas or activities that expose you to carbon monoxide.
High levels of carbon monoxide can collect rapidly in enclosed areas, such as a garage. Do not run the engine with the garage door closed. Even with the door open, run the engine only long enough to move the vehicle out of the garage.
Carbon Monoxide Hazard
With the tailgate open, airflow can pull exhaust gas into your vehicle’s interior and create a hazardous condition. If you must drive with the tailgate open, open all the windows, and set the heating and ventilation system/climate control system as shown below.
If you must sit in your parked vehicle with the engine running, even in an unconfined area, adjust the heating and ventilation system/climate control system as follows:
1. 2. 3. 4.
Select the fresh air mode. Select the mode. Set the fan speed to high. Set the temperature control to a comfortable setting.
Driver and Passenger Safety
65
06/12/06 10:37:26 32SMR600_069
Safety Labels
These labels are in the locations shown. They warn you of potential hazards that could cause serious injury. Read these labels carefully.
If a label comes off or becomes hard to read, contact your dealer for a replacement.
The label shown below is attached to the back of the bonnet.
SRS Airbag
SRS Airbag
CHILD SAFETY/SRS AIRBAG (Left-hand drive type)
CHILD SAFETY/SRS AIRBAG (Right-hand drive type)
BATTERY DANGER LABEL
Safety alert symbol
Follow service manual instructions carefully
SIDE AIRBAG
CHILD SAFETY
RADIATOR CAP DANGER LABEL (Petrol models)
EXPANSION TANK CAP DANGER LABEL (Diesel models)
SRS AIRBAG
66
Driver and Passenger Safety
06/12/06 10:37:34 32SMR600_070
Safety Labels
The label shown below is attached to each doorjamb.
on top of the
OnDieselmodels Symbols engine under the engine cover are to remind you to follow the service manual instructions. When replacing the injectors, your authorized dealer should perform this work. Contact your dealer.
Side Airbag
Safety alert symbol
Follow owner’ s manual instructions carefully
Driver and Passenger Safety
67
06/12/06 10:37:37 32SMR600_071
68
06/12/06 10:37:41 32SMR600_072
This section gives information about the controls and displays that contribute to the daily operation of your vehicle. All the essential controls are within easy reach.
Control Locations Instrument Panel Instrument Panel Indicators Gauges
. 70
. 72
. 76
. 84
mph to km/h Change Button . 85
Speedometer . 86........................... ............................ .......... ............................................. .... ...............................
Tachometer Temperature Gauge Fuel Gauge REV Indicator ECO Indicator i-VTEC Indicator
................................. ................... .................................. .............................. ............................. ......................... ..............
Multi-information Display Controls Near the Steering
. 86
. 86
. 86
. 87
. 87
. 88
. 89Wheel
.........................................
. 135
Windscreen Wipers and
Washers
Turn Signal and Headlights Front and Rear Fog Lights Instrument Panel Brightness Hazard Warning Button Rear Window Demister Headlight Adjuster Steering Wheel Adjustments Keys and Locks Immobilizer System Ignition Switch Door Locks
..................................... ......... .......... ...... ............... ............... ....................... ...... ............................. ...................... .............................. .................................... .................... ........................... ..................... ..........................................
Remote Transmitter Tailgate
Power Door Locks Super Locking
. 137
. 140
. 142
. 144
. 145
. 145
. 146
. 147
. 148
. 149
. 149
. 151
. 151
. 153
. 154
. 158Instruments and Controls
Seats
............................................... ...........
Front Seat Adjustments Driver’s Seat Height
. 160
. 160Adjustment
Head Restraints Armrests Folding the Rear Seats
Seat Heaters Luggage Area Cover Power Windows Sunshades Mirrors Parking Brake Interior Convenience Items
............................ ........................ .................................... ............. .................................. .................... ............................ ...................................... ........................................... ............................... ......... .................................. ......................... ..................... ......... .................................. ................................... ............................ ........ ........................... ...................... ....................................... ...............................
Glove Box Centre Console Beverage Holders Accessory Power Socket Coat Hook Sun Visor Vanity Mirror Under-floor Storage Area Centre Pocket Cigarette Lighter Ashtray
Interior Lights
. 162
. 162
. 163
. 164
. 166
. 167
. 168
. 170
. 172
. 174
. 175
. 176
. 177
. 178
. 179
. 179
. 180
. 180
. 180
. 182
. 182
. 183
. 183Instruments and Controls
69
06/12/06 10:37:48 32SMR600_073
Control Locations
Left-hand drive type
MULTI-INFORMATION DISPLAY
(P.89)
MIRROR CONTROLS (P.172)
POWER DOOR LOCK MASTER SWITCH (P.151)
POWER WINDOW SWITCHES (P.168)
FUEL FILL DOOR RELEASE HANDLE (P.299)
CLIMATE CONTROL (P.189, 195) SYSTEM
SUNSHADE SWITCH ＊ (P.170)
CLOCK (P.270)
AUDIO SYSTEM ＊ (P.212)
PASSENGER’S FRONT AIRBAG (P.12, 28)
HAZARD WARNING BUTTON (P.145)
BONNET RELEASE HANDLE
(P.301)
DRIVER’S FRONT AIRBAG (P.12, 28)
MANUAL TRANSMISSION i-SHIFT
(P.326)
(P.322)
Vehicle without navigation system is shown.
＊
If equipped
70
Instruments and Controls
06/12/06 10:37:55 32SMR600_074
Control Locations
Right-hand drive type
CLOCK (P.270)
CLIMATE CONTROL SYSTEM (P.189, 195)
SUNSHADE SWITCH ＊ (P.170)
MULTI-INFORMATION DISPLAY
(P.89)
HAZARD WARNING BUTTON (P.145)
PASSENGER’S FRONT AIRBAG (P.12, 28)
AUDIO SYSTEM ＊ (P.212)
DRIVER’S FRONT AIRBAG (P.12, 28)
MIRROR CONTROLS (P.172)
POWER DOOR LOCK MASTER SWITCH (P.151)
POWER WINDOW SWITCHES (P.168)
FUEL FILL DOOR RELEASE HANDLE (P.299)
MANUAL TRANSMISSION i-SHIFT
(P.326)
(P.322)
Vehicle without navigation system is shown.
＊:
If equipped
BONNET RELEASE HANDLE (P.301)
Instruments and Controls
71
06/12/06 10:38:03 32SMR600_075
Instrument Panel (Petrol models) Withmanualtransmission
HIGH BEAM INDICATOR (P.82) IMMOBILIZER SYSTEM (P.78) INDICATOR FRONT FOG LIGHT (P.80) INDICATOR MALFUNCTION INDICATOR LAMP (P.76, 467)
LOW OIL PRESSURE INDICATOR (P.77, 464) ELECTRIC POWER STEERING (EPS) INDICATOR (P.80)
CHARGING SYSTEM INDICATOR (P.77, 466)
LIGHTS ON INDICATOR (P.82)
ANTI-LOCK BRAKE SYSTEM INDICATOR (P.78)
CRUISE MAIN INDICATOR (P.81) SYSTEM MESSAGE INDICATOR (P.79)
CRUISE CONTROL INDICATOR (P.81)
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.79) VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.81) VSA ACTIVATION (P.81) INDICATOR LOW FUEL INDICATOR (P.83)
REAR FOG LIGHT INDICATOR (P.80)
SEAT BELT REMINDER INDICATOR (P.76)
SECURITY SYSTEM INDICATOR (P.83)
PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P.77, 470)
Since the indicators vary between models, some indicators are not on your vehicle. 72
Instruments and Controls
06/12/06 10:38:12 32SMR600_076
Withi-SHIFT
HIGH BEAM INDICATOR (P.82) IMMOBILIZER SYSTEM (P.78) INDICATOR FRONT FOG LIGHT (P.80) INDICATOR MALFUNCTION INDICATOR LAMP (P.76, 467)
i-SHIFT SYSTEM INDICATOR (P.79, 336) LOW OIL PRESSURE INDICATOR
(P.77, 464)
ELECTRIC POWER STEERING (EPS) INDICATOR (P.80)
CHARGING SYSTEM INDICATOR (P.77, 466)
LIGHTS ON INDICATOR (P.82)
Instrument Panel (Petrol models)
GEAR POSITION INDICATOR (P.326)
ANTI-LOCK BRAKE SYSTEM INDICATOR (P.78) CRUISE MAIN INDICATOR (P.81) SYSTEM MESSAGE INDICATOR (P.79)
CRUISE CONTROL INDICATOR (P.81)
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.79) VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.81) VSA ACTIVATION (P.81) INDICATOR LOW FUEL INDICATOR (P.83)
REAR FOG LIGHT INDICATOR (P.80)
SEAT BELT REMINDER INDICATOR (P.76)
SECURITY SYSTEM INDICATOR (P.83)
PARKING BRAKE AND BRAKE SYSTEM INDICATOR (P.77, 470)
Since the indicators vary between models, some indicators are not on your vehicle.
Instruments and Controls
73
06/12/06 10:38:20 32SMR600_077
Instrument Panel (Petrol models) Type-R
HIGH BEAM INDICATOR (P.82) IMMOBILIZER SYSTEM (P.78) INDICATOR FRONT FOG LIGHT (P.80) INDICATOR MALFUNCTION INDICATOR LAMP (P.76, 467)
LOW OIL PRESSURE INDICATOR
(P.77, 464)
ELECTRIC POWER STEERING (EPS) INDICATOR (P.80)
CHARGING SYSTEM INDICATOR (P.77, 466)
LIGHTS ON INDICATOR (P.82)
ANTI-LOCK BRAKE SYSTEM INDICATOR (P.78)
CRUISE MAIN INDICATOR (P.81)
SYSTEM MESSAGE INDICATOR (P.79)
CRUISE CONTROL INDICATOR (P.81)
SUPPLEMENTAL RESTRAINT SYSTEM INDICATOR (P.79) VEHICLE STABILITY ASSIST (VSA) SYSTEM INDICATOR (P.81) VSA ACTIVATION
