2011 Ford Ranger Owners Manual

• Driving on flat terrain offers improved fuel economy as compared to • Transmissions give their best fuel economy when operated in the top • Four-wheel drive operation (if equipped) is less fuel efficient than • Close windows for high speed driving. EMISSION CONTROL SYSTEM Your vehicle is equipped with various emission control components and a catalytic converter which will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your vehicle is moving, especially at • Have the items listed in scheduled maintenance information

high speeds.

performed according to the specified schedule.

The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system. 250

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

If other than Ford, Motorcraft威 or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability.

WARNING: Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the

engine compartment and exhaust system, which can start a fire.

Illumination of the service engine soon warning light or the temperature warning light, fluid leaks, strange odors, smoke or loss of engine power could indicate that the emission control system is not working properly. An improperly operating or damaged exhaust system may allow exhaust to enter the vehicle. Have a damaged or improperly operating exhaust system inspected and repaired immediately.

indicator, charging system

WARNING: Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment.

Do not make any unauthorized changes to your vehicle or engine. By law, vehicle owners and anyone who manufactures, repairs, services, sells, leases, trades vehicles, or supervises a fleet of vehicles are not permitted to intentionally remove an emission control device or prevent it from working. Information about your vehicle’s emission system is on the Vehicle Emission Control Information Decal located on or near the engine. This decal also lists engine displacement. Please consult your Warranty Guide for complete emission warranty information.

On-board diagnostics (OBD-II) Your vehicle is equipped with a computer that monitors the engine’s emission control system. This system is commonly known as the on-board diagnostics system (OBD-II). The OBD-II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD-II system also assists your authorized dealer in properly servicing your vehicle. When the service engine soon a malfunction. Temporary malfunctions may cause the service engine soon 1. The vehicle has run out of fuel—the engine may misfire or run poorly. 251

indicator illuminates, the OBD-II system has detected

indicator to illuminate. Examples are:

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly. 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter. 4. Driving through deep water—the electrical system may be wet. These temporary malfunctions can be corrected by filling the fuel tank with good quality fuel, properly tightening the fuel cap or letting the electrical system dry out. After three driving cycles without these or any other temporary malfunctions present, the service engine soon indicator should stay off the next time the engine is started. A driving cycle consists of a cold engine startup followed by mixed city/highway driving. No additional vehicle service is required. indicator remains on, have your vehicle If the service engine soon serviced at the first available opportunity. Although some malfunctions detected by the OBD-II may not have symptoms that are apparent, indicator on can continued driving with the service engine soon result in increased emissions, lower fuel economy, reduced engine and transmission smoothness, and lead to more costly repairs.

indicator is on or not working

Readiness for Inspection/Maintenance (I/M) testing Some state/provincial and local governments may have Inspection/Maintenance (I/M) programs to inspect the emission control equipment on your vehicle. Failure to pass this inspection could prevent you from getting a vehicle registration. Your vehicle may not pass the I/M test if the service engine soon properly (bulb is burned out), or if the OBD-II system has determined that some of the emission control systems have not been properly checked. In this case, the vehicle is considered not ready for I/M testing. If the service engine soon work, the vehicle may need to be serviced. Refer to On-board diagnostics (OBD-II) in this chapter. If the vehicle’s engine or transmission has just been serviced, or the battery has recently run down or been replaced, the OBD-II system may indicate that the vehicle is not ready for I/M testing. To determine if the vehicle is ready for I/M testing, turn the ignition key to the on position for 15 seconds without cranking the engine. If the service engine soon ready for I/M testing; if the service engine soon solid, it means that the vehicle is ready for I/M testing. 252

indicator blinks eight times, it means that the vehicle is not indicator stays on

indicator is on or the bulb does not

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving cycle consisting of mixed city and highway driving may be performed: 15 minutes of steady driving on an expressway/highway followed by 20 minutes of stop-and-go driving with at least four 30-second idle periods. Allow the vehicle to sit for at least eight hours without starting the engine. Then, start the engine and complete the above driving cycle. The engine must warm up to its normal operating temperature. Once started, do not turn off the engine until the above driving cycle is complete. If the vehicle is still not ready for I/M testing, the above driving cycle will have to be repeated.

POWER STEERING FLUID Check the power steering fluid. Refer to the scheduled maintenance guide for more information. • 2.3L I4 engine

• 4.0L V6 engine

1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near the center of the normal area between H and C).

253

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

2. While the engine idles, turn the steering wheel left and right several times. 3. Turn the engine off. 4. Check the fluid level in the reservoir. It should be between the MIN and MAX lines. Do not add fluid if the level is within this range. 5. If the fluid is low, add fluid in small amounts, until it reaches between the MIN and MAX lines. Refer to Maintenance product specifications and capacities in this chapter for the proper fluid type.

BRAKE FLUID The fluid level will drop slowly as the brakes wear, and will rise when the brake components are replaced. Fluid levels between the MIN and MAX lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range, the performance of the system could be compromised; seek service from your authorized dealer immediately.

CLUTCH FLUID (IF EQUIPPED) Check the fluid level. Refer to scheduled maintenance information for the service interval schedules. During normal operation, the fluid level in the clutch reservoir should remain constant. If the fluid level drops, refill the fluid level to the step in the reservoir. Use only a brake fluid designed to meet Ford specifications. Refer to Maintenance product specifications and capacities in this chapter.

254

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

1. Clean the reservoir cap before removal to prevent dirt and water from entering the reservoir. 2. Remove cap and rubber diaphragm from reservoir. 3. Add fluid until the level reaches the step in the reservoir. 4. Reinstall rubber diaphragm and cap onto reservoir.

TRANSMISSION FLUID

and change intervals.

Checking automatic transmission fluid • Refer to scheduled maintenance information for scheduled check • Transmission does not consume fluid. • Check fluid when transmission is not operating properly or if you see • Fluid level must be checked at normal operating temperature, 20 miles

a leak.

(30 km) of driving.

To check and add fluid: 1. Drive the vehicle 20 miles (30 km) to reach normal operating temperatures. 2. If driven in hot weather, city traffic, pulling a trailer, allow transmission to cool for 30 minutes before checking. 3. Engage parking brake, start engine. 4. Put your foot on the brake pedal and move the gearshift lever slowly through all of the gear ranges. 5. Shift to P (Park) and leave the engine running. 6. Remove the dipstick, wipe clean with a dry lint free rag. 7. Install and fully seat the dipstick into the filler tube. 8. Remove the dipstick and inspect the fluid level. Level should be in the cross-hatched area.

9. If necessary, add fluid in 1/2 pint (250 ml) increments through the filler tube until the level is correct at normal operating temperatures.

255

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

Refer to the Maintenance product specifications and capacities section in this chapter for the correct fluid type. The use of any other non-approved fluid may cause internal transmission damage. 10. Fluid can be checked at ambient temperatures between 50–95°F (10–30°C). DO NOT ADD fluid until the transmission is at normal operating temperatures or the transmission will be overfilled. Low fluid level Do not drive the vehicle if the fluid level is at or below the bottom of the dipstick.

High fluid level Fluid levels above the safe range may cause overheating, shift and/or engagement concerns and internal transmission damage. If an overfill condition occurs, excess fluid should be removed by an authorized dealer.

Checking and adding manual transmission fluid (if equipped) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level.

256

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

3. Fluid level should be at the bottom of the opening. 4. Add enough fluid through the filler opening so that the fluid level is at the bottom of the opening. 5. Install and tighten the fill plug securely.

Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter.

TRANSFER CASE FLUID (IF EQUIPPED) 1. Clean the filler plug. 2. Remove the filler plug and inspect the fluid level.

3. Add only enough fluid through the filler opening so that the fluid level is at the bottom of the opening.

Use only fluid that meets Ford specifications. Refer to the Maintenance product specifications and capacities section in this chapter.

257

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

DRIVELINE UNIVERSAL JOINT AND SLIP YOKE Your vehicle is equipped with universal joints that do not require lubrication. If the original universal joints are replaced with universal joints equipped with grease fittings, periodic lubrication will be necessary.

AIR FILTER Refer to scheduled maintenance information for the appropriate intervals for changing the air filter element. When changing the air filter element, use only the air filter element listed. Refer to Motorcraft威 part numbers in this chapter.

WARNING: To reduce the risk of vehicle damage and/or personal burn injuries do not start your engine with the air

cleaner removed and do not remove it while the engine is running.

1. Loosen the clamp that secures the air inlet tube to the engine air filter cover and disconnect the tube from the cover (for V6 only). 2. Release the clamps that secure the air filter housing cover. 3. Carefully separate the two halves of the air filter housing.

4. Remove the air filter element from the air filter housing. 5. Wipe the air filter housing and cover clean to remove any dirt or debris and to ensure good sealing.

258

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover. This could cause filter damage and allow unfiltered air to enter the engine if not properly seated.

7. Replace the air filter housing cover and secure the clamps. 8. Replace the air inlet tube and secure the clamp. Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if the correct air filter element is not used.

VEHICLE STORAGE If you plan on storing your vehicle for an extended period of time (30 days or more), refer to the following maintenance recommendations to ensure your vehicle stays in good operating condition. All motor vehicles and their components were engineered and tested for reliable, regular driving. Long term storage under various conditions may lead to component degradation or failure unless specific precautions are taken to preserve the components. General • Store all vehicles in a dry, ventilated place. • Protect from sunlight, if possible. • If vehicles are stored outside, they require regular maintenance to Body• Wash vehicle thoroughly to remove dirt, grease, oil, tar or mud from

protect against rust and damage.

exterior surfaces, rear-wheel housing and underside of front fenders. See the Cleaning chapter for more information. • Periodically wash vehicles stored in exposed locations. • Touch-up raw or primed metal to prevent rust. • Cover chrome and stainless steel parts with a thick coat of auto wax

to prevent discoloration. Re-wax as necessary when the vehicle is washed. See the Cleaning chapter for more information.

259

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

grade oil. See the Cleaning chapter for more information.

Maintenance and Specifications • Lubricate all hood, door and trunk lid hinges, and latches with a light • Cover interior trim to prevent fading. • Keep all rubber parts free from oil and solvents. Engine • The engine oil and filter should be changed prior to storage, as used • Start the engine every 15 days. Run at fast idle until it reaches normal • With your foot on the brake, shift through all the gears while the

engine oil contain contaminates that may cause engine damage.

operating temperature.

engine is running.

Fuel system • Fill the fuel tank with high-quality fuel until the first automatic shutoff

of the fuel pump nozzle.

Note: During extended periods of vehicle storage (30 days or more), fuel may deteriorate due to oxidation. Add a quality gas stabilizer product to the vehicle fuel system whenever actual or expected storage periods exceed 30 days. Follow the instructions on the additive label. The vehicle should then be operated at idle speed to circulate the additive throughout the fuel system. Cooling system • Protect against freezing temperatures. • When removing vehicle from storage, check coolant fluid level. Confirm there are no cooling system leaks, and fluid is at the recommended level.

Battery • Check and recharge as necessary. Keep connections clean. • If storing your vehicle for more than 30 days without recharging the battery, it may be advisable to disconnect the battery cables to ensure battery charge is maintained for quick starting.

Note: If battery cables are disconnected, it will be necessary to reset memory features.

260

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

Brakes • Make sure brakes and parking brake are fully released. Tires • Maintain recommended air pressure. Miscellaneous • Make sure all linkages, cables, levers and pins under vehicle are • Move vehicles at least 25 feet (8 m) every 15 days to lubricate

covered with grease to prevent rust.

working parts and prevent corrosion.

window surfaces.

during storage (mice/squirrel nests).

Removing vehicle from storage When your vehicle is ready to come out of storage, do the following: • Wash your vehicle to remove any dirt or grease film build-up on • Check windshield wipers for any deterioration. • Check under the hood for any foreign material that may have collected • Check the exhaust for any foreign material that may have collected • Check tire pressures and set tire inflation per the Tire Label. • Check brake pedal operation. Drive the vehicle 15 ft (4.5 meters) back • Check fluid levels (including coolant, oil and gas) to make sure there • If the battery was removed, clean the battery cable ends and inspect. If you have any concerns or issues, contact your authorized dealer.

are no leaks, and fluids are at recommended levels.

and forth to remove rust build-up.

during storage.

261

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

4.0L V6 Engine FA-1744
FG-1036
BXT-59
FL-820S

2.3L I4 Engine FA-1744
FG-1036
BXT-59
FL-910S

MOTORCRAFT PART NUMBERS Component Air filter element Fuel filter Battery Oil filter Spark plugs 1For spark plug replacement, see your authorized dealer. Refer to scheduled maintenance information for the appropriate intervals for changing the spark plugs. Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft威 or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used.

262

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

威

威

—

—

—

–

威

–

263

2011 Ranger (ran) Owners Guide, 2nd Printing USA (fus)

Maintenance and Specifications

威

威

威

威

威

威

威