You may also be interested in...

2009 Ford F 150 Owners Manual

Download PDF Manual

adjustment. Most geographic areas (zones) have a magnetic north compass point that varies slightly from the northerly direction on maps. This variation is four degrees between adjacent zones and will become noticeable as the vehicle crosses multiple zones. A correct zone setting will eliminate this error. Refer to Compass zone adjustment.


68


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


23


15


14
13
12


7 8 9 1011


Compass zone adjustment 1. Determine which magnetic zone you are in for your geographic location by referring to the zone map. 2. Turn ignition to the on position.


3. Press and hold the 7 and 9 radio preset buttons together for approximately five seconds until ZONE XX appears in the CID.


4. Press and release the 7 and 9
radio preset buttons together, repeatedly until ZONE XX changes to the correct zone (1–15) in the CID.


5. The direction will display after the buttons are released. The zone is now updated.


Compass calibration adjustment Perform compass calibration in an open area free from steel structures and high voltage lines. For optimum calibration, turn off all electrical accessories (heater/air conditioning, wipers, etc.) and make sure all vehicle doors are shut. 1. Start the vehicle.


69


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


2. To calibrate, press and hold the 7
and 9 radio preset buttons together for approximately 10 seconds until CAL appears. Release the buttons.


3. Slowly drive the vehicle in a circle (less than 3 mph [5 km/h]) until the CAL display changes to the direction value (N, S, E, W, etc.). It may take up to five circles to complete calibration. 4. The compass is now calibrated. AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only. Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty. The auxiliary power point is located on the instrument panel. Do not use the power point for operating the cigarette lighter element (if equipped). To prevent the fuse from being blown, do not use the power point(s) over the vehicle capacity of 12 VDC/180W. If the power point or cigar lighter socket is not working, a fuse may have blown. Refer to Fuses and relays in the Roadside Emergencies chapter for information on checking and replacing fuses. To have full capacity usage of your power point, the engine is required to be running to avoid unintentional discharge of the battery. To prevent the battery from being discharged: • do not use the power point longer than necessary when the engine is • do not leave battery chargers, video game adapters, computers and other devices plugged in overnight or when the vehicle is parked for extended periods.


not running,


70


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


An additional auxiliary power point is located on the lower rear side of the center console. The power point is accessible from the rear seats. Always keep the power point caps closed when not being used.


Cigarette/Cigar lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold the lighter in with your hand while it is heating, this will damage the lighter element and socket. The lighter will be released from its heating position when it is ready to be used. Note: Improper use of the lighter can cause damage not covered by your warranty, and can result in fire or serious injury.


Cupholder/Ashtray (if equipped) The cupholder/ashtray is located on the instrument panel. To open cupholder/ashtray, push in on the door and release. The door will spring out 1/4+ inches. Then pull cupholder/ashtray assembly out the remaining distance to utilize. To close, push assembly in completely and release.


71


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Ashtray (if equipped) The ashtray is located on the instrument panel. To open ashtray, push in on the door and release. The ashtray assembly will tip out. To close, push assembly in completely and release. Up-level ashtray shown; base similar.


POWER WINDOWS


WARNING: Do not leave children unattended in the vehicle and do not let children play with the power windows. They may


seriously injure themselves.


WARNING: When closing the power windows, you should verify they are free of obstructions and ensure that children and/or


pets are not in the proximity of the window openings.


Press and pull the window switches to open and close windows. • Push down (to the first detent) • Pull up (to the first detent) and


and hold the switch to open.


hold the switch to close.


Rear Window Buffeting: When one or both of the rear windows are open, the vehicle may demonstrate a wind throb or buffeting noise. This noise can be alleviated by lowering a front window approximately two to three inches.


72


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


One touch down Allows the driver’s window to open fully without holding the control down. Press the switch completely down to the second detent and release quickly. The window will open fully. Momentarily press the switch to any position to stop the window operation.


Window lock The window lock feature allows only the driver to operate the power windows. To lock out all the window controls (except for the driver’s) press the right side of the control. Press the left side to restore the window controls. Note: The rear window switches will not illuminate when the window control is in the locked position.


Power sliding back window (if equipped) the control Press and hold the to open the window all the way to the full open position. Pull and hold the close the window.


control to


WARNING: When operating the power sliding back window you must ensure all rear seat occupants and/or cargo are not in the


proximity of the back window.


73


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


WARNING: Do not leave children unattended in the vehicle and do not let children play with the power sliding back window.


They may seriously injure themselves.


Accessory delay (if equipped) With accessory delay, the window switches may be used for up to 10 minutes after the ignition switch is turned to the off position or until any door is opened.


INTERIOR MIRROR The interior rear view mirror has two pivot points on the support arm which lets you adjust the mirror up or down and from side to side.


WARNING: Do not adjust the mirror while the vehicle is in motion.


Automatic dimming interior rear view mirror (if equipped) Your vehicle may be equipped with an interior rear view mirror that has an auto-dimming function (optional on the driver’s side exterior mirror). The electronic day/night mirror will change from the normal (high reflective) state to the non-glare (darkened) state when bright lights (glare) reach the interior mirror. When the interior mirror detects bright light from behind the vehicle, the interior rear view mirror and the driver’s side exterior mirror (if equipped) will automatically adjust (darken) to minimize glare. Without microphone


74


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


With microphone


Driver Controls


The mirrors will automatically return to the normal state whenever the vehicle is placed in R (Reverse) to ensure a bright clear view when backing up. Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. Note: If equipped with a reverse camera system, a video image will display in the mirror or the Navigation system display (if equipped) when the vehicle is put in R (Reverse). As you shift into any other gear from R (Reverse), the image will remain for a few seconds and then turn off. Refer to Reverse camera system in the Driving chapter.


EXTERIOR MIRRORS


Power side view mirrors (if equipped)


WARNING: Do not adjust the mirror while the vehicle is in motion.


To adjust your mirrors: 1. Rotate the control clockwise to adjust the right mirror and rotate the control counterclockwise to adjust the left mirror. 2. Move the control in the direction you wish to tilt the mirror. 3. Return to the center position to lock mirrors in place. Memory feature (if equipped) The power side view mirror positions are saved when doing a memory set function and can be recalled along with the vehicle personality features when a memory position is selected through the remote entry


75


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


transmitter, keyless entry keypad or memory switch on the driver’s seat. Refer to Memory seats and mirrors in the Seating and Safety Restraints chapter. Automatic dimming feature (if equipped) The driver’s side view mirror has an auto-dimming function. For more information, refer to Automatic dimming interior rear view mirror in this chapter.


Fold-away mirrors Fold the side mirrors in carefully before driving through a narrow space, like an automatic car wash. Powerfold mirrors (if equipped) With powerfold mirrors, you can fold the side mirrors using the power mirror switch. 1. Rotate the switch to the center/neutral position. 2. Momentarily pull the switch rearward to auto fold in. 3. Momentarily pull the switch rearward again to fold back to design position. The powerfold mirrors may be moved inward/outward manually. However, if a mirror is moved manually, it will need to be reset. A mirror which has not been reset may appear to be loose. To reset: with the switch in the center position, momentarily pull the switch rearward to fold the mirrors in. An audible ⬙click⬙ will be heard indicating re-synchronization. If the click is not heard, use the switch to fold the mirrors out, then in, until the click is heard. After that, the mirrors will operate normally until they are again moved manually. Note: 10 or more switch activations within one minute, or repeated folding/unfolding of the mirrors while holding the switch rearward during full travel, may cause the system to disable the fold/unfold function to protect motors from overheating. Should this occur, wait approximately three minutes with the vehicle running and up to 10 minutes with the vehicle off, for the system to reset and for function to return to normal.


76


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Heated outside mirrors (if equipped) Heated mirrors remove ice, mist and fog. To activate the heated mirrors, press the rear defrost button R located on the climate control panel. Refer to Rear window defroster in the Climate Controls chapter for more information. On vehicles not equipped with rear defrost, press the heated mirror control refer to the Climate Controls chapter. Note: If your vehicle is equipped with the Auto dimming feature, the mirror glass is thicker and will take longer to defrost. Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products.


located on the climate control panel. For more information


Exterior mounted mirror turn signal indicator (if equipped) When the vehicle turn signal is activated, the lower portion of the mirror housing will blink. This feature provides an indicator to the driver that the vehicle turn signal is working properly.


77


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Telescoping trailer tow mirrors (if equipped) The telescoping feature allows the mirror to extend approximately 3.5 inches (90 mm). This feature is especially useful to the driver when towing a trailer. Pull the mirrors inward carefully when driving through a narrow space.


POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the right side of the control to adjust the pedals toward you. • Press the left side of the control to adjust the pedals away from you.


WARNING: Never adjust the accelerator and brake pedal with feet on the pedals while the vehicle is moving.


POWER DEPLOYABLE RUNNING BOARDS (IF EQUIPPED) Deployable running boards (DRB) automatically move when the doors are opened to assist entering and exiting the vehicle.


78


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Automatic power deploy: • The running boards will extend


down and out when the doors are opened.


Automatic power stow: • The running boards will return to the stowed position when the doors are closed. There will be a two second delay before the running boards move in to the stowed position.


Manual power deploy: To manually operate the running boards, refer to the Message center in this chapter. • This feature can manually set the running boards in the deployed • When running boards are manually set in the deployed position , the boards will return to the stowed position and enter automatic mode when the vehicle speed exceeds 5 mph (8 km/h).


position for access to the roof.


Enable/disable: To enable/disable the power running board feature, refer to the Message center in this chapter. • When this feature is disabled , the running boards will move to • When this feature is enabled , the running boards will move


the stowed position regardless of the position of the doors.


back to the correct positions based off of the door positions.


Bounce-back: • If an object is in the way of the moving running board, the running board will automatically bounce back in the reverse direction and move to the end of travel.


Note: The running boards may operate slower in cooler temperatures. In adverse conditions, debris such as mud, dirt, and salt may become trapped in the running board mechanism, possibly leading to unwanted noise. If this occurs, manually set the running boards to the deployed position and flush the system (in particular the front and rear hinge arms) with a high-pressure car wash wand.


79


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Note: Do not use the running boards, front and rear hinge assemblies, running board motors, or the running board under body mounts to lift the vehicle when jacking. Please utilize proper jacking points. Refer to Changing the tires in the Roadside Emergencies chapter.


WARNING: In extreme climates, excessive ice buildup may occur, causing the running boards not to deploy. Be sure that the


running boards have deployed, and have finished moving before attempting to step on them. Note: The running boards will resume normal function once the blockage is cleared.


WARNING: Turn off the running boards before jacking or placing any object under the vehicle. Never place your hand


between the extended running board and the vehicle. A moving running board may cause injury.


SPEED CONTROL (IF EQUIPPED) With speed control set, you can maintain a set speed without keeping your foot on the accelerator pedal.


WARNING: Do not use the speed control in heavy traffic or on roads that are winding, slippery or unpaved.


Setting speed control The controls for using your speed control are located on the steering wheel for your convenience. 1. Press the ON control and release it. 2. Accelerate to the desired speed.


80


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


3. Press the SET + or SET - control and release it. 4. Take your foot off the accelerator pedal. 5. The indicator instrument cluster will turn on.


light on the


steep hill.


Note: • Vehicle speed may vary momentarily when driving up and down a • If the vehicle speed increases above the set speed on a downhill, you • If the vehicle speed decreases more than 10 mph (16 km/h) below


may want to apply the brakes to reduce the speed.


your set speed on an uphill, your speed control will disengage.


Disengaging speed control To disengage the speed control: • Depress the brake pedal. Disengaging the speed control will not erase previous set speed. Resuming a set speed Press the RESUME control and release it. This will automatically return the vehicle to the previously set speed.


81


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. You can also use the SET + control to operate the Tap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 km/h).


• Use the accelerator pedal to get to the desired speed. When the vehicle reaches that speed press and release the SET + control.


Reducing speed while using speed control There are two ways to reduce a set speed: • Press and hold the SET - control until you get to the desired speed, then release the control. You can also use the SET - control to operate the Tap-Down function. Press and release this control to decrease the vehicle set speed in small amounts by 1 mph (1.6 km/h).


• Depress the brake pedal until the desired vehicle speed is reached and


press the SET + control.


82


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Turning off speed control There are two ways to turn off the speed control: • Depress the brake pedal or the clutch pedal (if equipped). This will not erase your vehicle’s previously set speed. • Press the speed control OFF


control.


Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased.


STEERING WHEEL CONTROLS (IF EQUIPPED) Radio control features Press MEDIA to select: • AM, FM1, FM2, or CD • SAT1, SAT2 or SAT3 (Satellite • LINE IN (auxiliary input jack)


Radio mode).


In radio mode: • Press


to access the


next/previous preset station.


In CD mode: • Press


to listen to the


next track on the disc. In satellite radio mode: • Press


to advance


through preset channels.


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


83


Driver Controls


In any mode: • Press VOL + or VOL - to adjust


the volume.


SYNC威 system hands free control features briefly to use the voice Press command feature. You will hear a tone and LISTENING will appear in the radio display. Press and hold to activate phone mode or Press answer a phone call. Press VOL + or − to adjust volume. Press and hold


to exit voice command.


to end a call or exit phone mode.


to scroll through various menus and selections. Press


Press OK to confirm your selection. For further information on the SYNC威 system, refer to the SYNC威 supplement. Navigation system/SYNC威 hands free control features (if equipped) Press voice Navigation display to use the voice command feature. to activate phone mode or Press answer a phone call. Press VOL + or − to adjust volume. Press and hold


control briefly until the icon appears on the


to exit phone mode or end a call.


84


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


For further information on the Navigation system/SYNC威 system, refer to the Navigation and SYNC威 supplements.


MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console.


WARNING: Do not let children play with the moon roof or leave children unattended in the vehicle. They may seriously hurt


themselves.


WARNING: When closing the moon roof, you should verify that it is free of obstructions and ensure that children and/or pets are


not in the proximity of the moon roof opening.


The moon roof is equipped with an automatic, one-touch, express opening and closing feature. To stop motion at any time during the one-touch operation, press the control a second time. To open the moon roof: Press and release the SLIDE control, the moon roof will open automatically. Press the switch again to stop the moon roof. To close the moon roof: Pull and release the SLIDE control, the moon roof will close automatically. Press the switch again to stop the moon roof. Bounce-back: When an obstacle has been detected in the moon roof opening as the moon roof is closing, the moon roof will automatically open and stop at a prescribed position. Bounce-back override: To override bounce-back function, pull and hold the SLIDE switch within two seconds of a bounce-back event. The closing force will begin to increase each time the moon roof is closed for the first three closing cycles, with bounce-back active. For example: Bounce-back can be used to overcome the resistance of ice on the moon roof or seals To vent the moon roof: Press and release the TILT control, the moon roof will move to the vent position automatically from any moon roof position. Press the switch again to stop the moon roof. Pull and hold the TILT control to close the moon roof.


85


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. To close the shade, pull it toward the front of the vehicle.


HOMELINK姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink威 Wireless Control System, located on the driver’s visor, provides a convenient way to replace up to three hand-held transmitters with a single built-in device. This feature will learn the radio frequency codes of most transmitters to operate garage doors, entry gate operators, security systems, entry door locks, and home or office lighting.


WARNING: When programming your HomeLink威 Wireless Control System to a garage door or gate, be sure that people and


objects are out of the way to prevent potential injury or damage.


Do not use the HomeLink威 Wireless Control System with any garage door opener that lacks safety stop and reverse features as required by U.S. federal safety standards (this includes any garage door opener model manufactured before April 1, 1982). A garage door which cannot detect an object, signaling the door to stop and reverse, does not meet current U.S. federal safety standards. For more information, contact HomeLink威 at: www.homelink.com or 1–800–355–3515. Retain the original transmitter for use in other vehicles as well as for future programming procedures (i.e. new HomeLink威 equipped vehicle purchase). It is also suggested that upon the sale of the vehicle, the programmed Homelink威 buttons be erased for security purposes, refer to Programming in this section.


Programming Do not program HomeLink威 with the vehicle parked in the garage. Note: Your vehicle may require the ignition switch to be turned to the accessory position for programming and/or operation of the HomeLink威. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink威 for quicker training and accurate transmission of the radio-frequency signal.


86


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


1. Position the end of your hand-held transmitter 1–3 inches (2–8 cm) away from the HomeLink威 button you wish to program (located on your visor) while keeping the indicator light in view. 2. Simultaneously press and hold both the chosen HomeLink威 and hand-held transmitter buttons until the HomeLink威 indicator light changes from a slow to a rapidly blinking light. Now you may release both the HomeLink威 and hand-held transmitter buttons. Note: Some entry gates and garage door openers may require you to replace Step 2 with procedures noted in the Gate Operator and Canadian Programming in this section for Canadian residents. 3. Firmly press and hold for five seconds and release the programmed HomeLink威 button up to two separate times to activate the door. If the door does not activate, press and hold the just-trained HomeLink威 button and observe the indicator light. • If the indicator light stays on constantly, programming is complete and your device should activate when the HomeLink威 button is pressed and released. • If the indicator light blinks rapidly for two seconds and then turns to a constant light continue with “Programming” Steps 4 through 6 to complete programming of a rolling code equipped device (most commonly a garage door opener). 4. At the garage door opener receiver (motor-head unit) in the garage, locate the “learn” or “smart” button (usually near where the hanging antenna wire is attached to the unit). 5. Firmly press and release the “learn” or “smart” button. (The name and color of the button may vary by manufacturer.) Note: There are 30 seconds in which to initiate Step 6. 6. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to complete the programming. HomeLink威 should now activate your rolling code equipped device. To program additional HomeLink威 buttons begin with Step 1 in this section. For questions or comments, please contact HomeLink威 at www.homelink.com or 1–800–355–3515.


87


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Gate Operator & Canadian Programming During programming, your hand-held transmitter may automatically stop transmitting — not allowing enough time for HomeLink威 to accept the signal from the hand-held transmitter. After completing Step 1 outlined in the Programming section, replace Step 2 with the following: Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent overheating. • Continue to press and hold the HomeLink威 button (note Step 2 in the


Programming section) while you press and release — every two seconds (“cycle”) your hand-held transmitter until the frequency signal has been accepted by the HomeLink威. The indicator light will flash slowly and then rapidly after HomeLink威 accepts the radio frequency signal.


• Proceed with Step 3 in the Programming section.


Operating the HomeLink姞 Wireless Control System To operate, simply press and release the appropriate HomeLink威 button. Activation will now occur for the trained product (garage door, gate operator, security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used at any time. In the event that there are still programming difficulties, contact HomeLink威 at www.homelink.com or 1–800–355–3515.


88


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Erasing HomeLink姞 buttons To erase the three programmed buttons (individual buttons cannot be erased): • Press and hold the two outer HomeLink威 buttons until the indicator light begins to flash-after 20 seconds. Release both buttons. Do not hold for longer that 30 seconds.


HomeLink威 is now in the train (or learning) mode and can be programmed at any time beginning with Step 1 in the Programming section. Reprogramming a single HomeLink姞 button To program a device to HomeLink威 using a HomeLink威 button previously trained, follow these steps: 1. Press and hold the desired HomeLink威 button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink威 button, follow Step 1 in the Programming section. For questions or comments, contact HomeLink威 at www.homelink.com or 1–800–355–3515.


STANDARD MESSAGE CENTER (IF EQUIPPED) With the ignition in the on position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.


Selectable features Press and release the SELECT/RESET stem, located in the speedometer, to scroll and reset the following functions. Select or reset the function by pressing and holding the SELECT/RESET stem for more than two seconds.


89


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Info menu This menu displays the following: • Odometer/Trip Odometer (Trip A and Trip B) • Distance to Empty • Hold Reset for Setup Menu • Hold Reset for System check • Blank Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Select this function to estimate approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel. The DTE function will display XXX MILES TO E FUEL LEVEL LOW and sound a chime for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and chime will return within 10 minutes. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is re-initialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing miles traveled by gallons of fuel used (liters of fuel used by 100 kilometers traveled), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up 90


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


service stations


• Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter) 1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the SELECT/RESET stem (press and hold for two seconds in order to reset the function) after setting the speed control to get accurate highway fuel economy readings. Setup Menu Press and hold the SELECT/RESET stem to get into the SETUP menu sequence from the INFO menu for the following items: • Oil Life • Units (English/Metric) • Rear Park Aid (if equipped) • Autolamp (if equipped) • Autolock (if equipped) • Autounlock (if equipped) • Easy Entry (if equipped) • Trailer Sway (if equipped) • Language • Reset to English–if in another language (see Note below) Note: When returning to the SETUP menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed to change back to English. Press and hold the SELECT/RESET stem to change back to English. Oil Life XXX% HOLD RESET = NEW An oil change is required whenever indicated by the message center. USE ONLY RECOMMENDED ENGINE OILS.


91


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


To reset the oil monitoring system to 100% after each oil change [approximately 7,500 miles (12,000 km) or six months] perform the following: 1. Press and release the SELECT/RESET stem to display OIL LIFE = XXX% HOLD RESET = NEW.


2. Press and hold the SELECT/RESET stem for two seconds and release. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed. 3. While “OIL LIFE SET TO 100%” is displayed, if a lower oil life start value is desired, press and release the RESET control to reduce the start value. Each press of the SELECT/RESET stem reduces the value by 10 percent. Note: Oil life start value of 100% equals 7,500 miles (12,000 km) or six months. For example, setting oil life start value to 60% sets the oil life start value to 4,500 miles (7,200 km) and 108 days. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press and hold the SELECT/RESET stem to change from English to Metric. 3. Press the SELECT/RESET stem for the next SETUP menu item or wait for more than four seconds to return to the INFO menu. Rear Park Aid (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected.


92


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


1. To disable/enable the reverse sensing system feature with the vehicle in P (Park), select this function from the SETUP MENU or put the vehicle in R (Reverse). 2. Press and hold the SELECT/RESET stem to turn the park aid ON or OFF. 3. Press the SELECT/RESET stem for the next SETUP MENU item or wait for more than four seconds to return to the INFO menu. Autolamp This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP MENU. 2. Press and hold the SELECT/RESET stem to select the new Autolamp delay values of 0, 10, 20, 30, 60, 90, 120 or 180 seconds. Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1. To disable/enable the autolock feature, select this function from the SETUP MENU. 2. Press and hold the SELECT/RESET stem to turn the autolock ON or OFF. Autounlock This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off. 1. To disable/enable the autounlock feature, select this function from the SETUP MENU. 2. Press and hold the SELECT/RESET stem to turn the autounlock ON or OFF.


93


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Easy Entry (if equipped) This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy entry/exit seat feature, select this function from the SETUP menu. 2. Press and hold the SELECT/RESET stem to turn the easy entry/exit seat on or off. Trailer sway (if equipped) This feature uses the electronic stability control to mitigate trailer sway. 1. To disable/enable the trailer sway feature, select this function from the SETUP menu. 2. Press the SELECT/RESET stem to turn the trailer sway on or off. Language 1. Select this function from the SETUP menu. 2. Press and hold the SELECT/RESET stem to select a new language. Selectable languages are English, Spanish and French 3. Press the SELECT/RESET stem for the next SETUP menu item or wait for more than four seconds to return to the INFO menu. Reset to English (if in another language) When entering the SETUP menu and a non-English language has been selected, HOLD RESET FOR ENGLISH will be displayed. Press and hold the SELECT/RESET stem to set the language choice.


94


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


RESET FOR SYSTEM CHECK Press and hold the SELECT/RESET stem to get into the system check sequence from the INFO menu for the following items: The message center will cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for two seconds. The sequence of the system check report and how it appears in the message center is as follows: 1. XXX% OIL LIFE 2. CHARGING SYSTEM 3. DOOR STATUS 4. BRAKE FLUID LEVEL 5. XX MILES TO E FUEL LEVEL XXX 6. TBC GAIN = XX.X NO TRAILER (if equipped and no trailer connected) 7. TBC GAIN = XX.X OUTPUT = ////// (if equipped and trailer connected)


System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the SELECT/RESET stem and clearing the warning message. Warning messages can be divided into three categories: • Cannot be cleared until the condition is corrected. • Reappears 10 minutes after resetting it. • Reappears if the condition clears, then reoccurs within the same


ignition on/off cycle.


95


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Warning display Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar XXX miles to E fuel level low Check charging system Tire pressure sensor fault Low tire pressure Service RSC now Check fuel fill inlet Check 4x4 (if equipped) Tire pressure monitor fault Brake fluid level low Trailer brake module fault (if equipped) Oil change required XX% Oil life change soon Wiring fault on trailer (if equipped) Check rear park aid (if equipped) Trailer disconnected (if equipped)


Check brake system


96


Status The warning can return after the ignition key is turned from off to on if the condition still exists.


The warning can be reset. If the condition/problem occurs again, the message can return after being reset. The warning can return after the ignition key is turned from off to on if the condition/problem still exists.


The warning can be reset. The warning can return after the ignition key is turned from off to on if the condition/problem still exists.


The warning can be reset. The warning can return immediately after being reset if the condition/problem still exists. The warning will return 10 minutes after being reset if the condition/problem still exists. The warning can return after the ignition key is turned from off to on if the condition/problem still exists.


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Warning display Park brake engaged


Trailer sway reduce speed


Driver Controls


Status The warning can be reset. The warning can return immediately after being reset if the condition still exists. The warning will return 10 minutes after being reset if the condition/problem still exists. The warning can return after the ignition key is turned from off to on if the condition still exists. The warning can be reset. The warning can return immediately after being reset if the condition still exists. Temporary alert


For 4x4 low stop vehicle (if equipped) For 4x4 low shift to N (if equipped) To exit 4x4 low stop vehicle (if equipped) To exit 4x4 low shift to N (if equipped) Trailer connected Train left front tire Train right front tire Train right rear tire Train left rear tire Tires not trained – repeat Training complete DRIVER DOOR AJAR — Displayed when the driver door is not completely closed. PASSENGER DOOR AJAR — Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed.


97


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


XXX MILES TO E FUEL LEVEL LOW — Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM — Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, contact your authorized dealer as soon as possible TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible LOW TIRE PRESSURE — Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. SERVICE RSC NOW — Displayed when the RSC system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuel system in the Maintenance and Specifications chapter. CHECK 4X4 (if equipped) — Displayed when a 4X4 system fault is present. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TIRE PRESSURE MONITOR FAULT — Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid in the Maintenance and Specifications chapter. TRAILER BRAKE MODULE FAULT (if equipped) — Displayed and accompanied by a single chime, in response to faults sensed by the TBC. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. OIL CHANGE REQUIRED — Displayed when an oil change is required. XX% OIL LIFE CHANGE SOON — Displayed when an oil change will soon be required and shows the percentage of oil life left.


98


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


WIRING FAULT ON TRAILER (if equipped) — Displayed if there are certain faults in the vehicle wiring and trailer wiring/brake system. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. CHECK REAR PARK AID (if equipped) — Displayed when the transmission is in R (Reverse). Refer to Reverse sensing system in the Driving chapter. TRAILER DISCONNECTED (if equipped) — Displayed when a trailer connection becomes disconnected, either intentionally or unintentionally, and has been sensed during a given ignition cycle. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. CHECK BRAKE SYSTEM — Displayed when a fault has been detected by the ABS module. PARK BRAKE ENGAGED — Displayed when the parking brake is engaged. TRAILER SWAY REDUCE SPEED (if equipped) — Displayed when the trailer sway control has detected trailer sway. For more information, refer to the Driving chapter for more information. FOR 4X4 LOW STOP VEHICLE (if equipped) — Displayed when 4X4 LOW is selected while the vehicle is moving. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. FOR 4X4 LOW SHIFT TO N (if equipped) — Displayed when 4X4
LOW is selected and the vehicle is stopped. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TO EXIT 4X4 LOW STOP VEHICLE (if equipped) — Displayed when 2WD is selected while the vehicle is operating in 4X4 LOW. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when 2WD is selected while the vehicle has been stopped in 4X4 LOW. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TRAILER CONNECTED (if equipped) — Displayed when a correct trailer connection (a trailer with electric trailer brakes) is sensed during a given ignition cycle. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. TRAIN LEFT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information.


99


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


TRAIN RIGHT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN RIGHT REAR TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN LEFT REAR TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TIRES NOT TRAINED – REPEAT (if equipped) — Displayed when an error occurs while training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAINING COMPLETE (if equipped) — Displayed when training of the TPMS system is complete. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information.


OPTIONAL MESSAGE CENTER (IF EQUIPPED) With the ignition in the on position, the message center, located on your instrument cluster, displays important vehicle information through a constant monitor of vehicle systems. You may select display features on the message center for a display of status preceded by a brief indicator chime. The system will also notify you of potential vehicle problems with a display of system warnings followed by a long indicator chime.


Selectable features Reset Press this control to select and reset functions shown in the INFO menu and SETUP menu.


Info menu This control displays the following control displays: • Trip odometer/Odometer • Distance to Empty • Average Fuel Economy


100


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


• Instantaneous Fuel Economy • Trip Elapsed Drive Time • Blank Odometer/Trip odometer Refer to Gauges in the Instrument Cluster chapter. Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition off when refueling to allow this feature to correctly detect the added fuel. The DTE function will display XXX MILES TO E FUEL LEVEL LOW and sound a tone for one second when you have approximately 50 miles (80 km) to empty. If you RESET this warning message, this display and tone will return within 10 minutes. DTE is calculated using a running average fuel economy, which is based on your recent driving history of 500 miles (800 km). This value is not the same as the average fuel economy display. The running average fuel economy is re-initialized to a factory default value if the battery is disconnected. Average fuel economy (AFE) Select this function from the INFO menu to display your average fuel economy in miles/gallon or liters/100 km. If you calculate your average fuel economy by dividing 100 miles traveled by gallons of fuel used (kilometers traveled by liters used), your figure may be different than displayed for the following reasons: • Your vehicle was not perfectly level during fill-up • Differences in the automatic shut-off points on the fuel pumps at • Variations in top-off procedure from one fill-up to another • Rounding of the displayed values to the nearest 0.1 gallon (liter)


service stations


101


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


, one or no bars


poor economy to


1. Drive the vehicle at least 5 miles (8 km) with the speed control system engaged to display a stabilized average. 2. Record the highway fuel economy for future reference. It is important to press the RESET control after setting the speed control to get accurate highway fuel economy readings. Instantaneous fuel economy Select this function from the INFO menu to display your instantaneous fuel economy. This will display your fuel economy as a bar graph ranging from excellent economy. Your vehicle must be moving to calculate instantaneous fuel economy. When your vehicle is not moving, this function shows illuminated. Instantaneous fuel economy cannot be reset. Trip elapsed drive time Select this function from the INFO menu to display a timer. To operate the Trip Elapsed Drive Time perform the following: 1. Press and release RESET in order to start the timer. 2. Press and release RESET to pause the timer. 3. Press and hold RESET for two seconds in order to reset the timer. Blank screen Press the RESET once to turn the message center display off. Setup menu Press this control for the following displays: • Reset For System Check • Oil Life • Rear Park Aid (if equipped) • Running Boards (if equipped) • Autolamp 102


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


• Autolock • Autounlock • Easy Entry (if equipped) • Trailer Sway (if equipped) • Units (English/Metric) • Language • Reset to English (if in another language) Reset For System check Selecting this function from the SETUP menu causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for three seconds. Pressing the RESET control cycles the message center through each of the systems being monitored. The sequence of the system check report and how it appears in the message center is as follows: 1. XXX% OIL LIFE 2. CHARGING SYSTEM 3. DOOR STATUS 4. BRAKE FLUID LEVEL 5. XX MILES TO E FUEL LEVEL XXX 6. TBC GAIN = XX.X NO TRAILER (if equipped and no trailer connected) 7. TBC GAIN = XX.X OUTPUT = ////// (if equipped and trailer connected) Oil Life XXX% HOLD RESET = NEW An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONLY RECOMMENDED ENGINE OILS.


103


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


To reset the oil monitoring system to 100% after each oil change (approximately 7,500 miles [12,000 km] or six months) perform the following: 1. Press and release the SETUP control to display “OIL LIFE XXX% HOLD RESET = NEW”.


2. Press and hold the RESET control for two seconds and release. Oil life is set to 100% and “OIL LIFE SET TO 100%” is displayed.


Note: To change oil life 100% miles value from 7,500 miles (12,000 km) or six months to another value, proceed to Step 3. 3. Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET control switch to change the Oil Life Start Value. Each release and press will reduce the value by 10%. Rear Park Aid (if equipped) This feature sounds a warning tone to warn the driver of obstacles near the rear bumper, and functions only when R (Reverse) gear is selected. 1. To disable/enable the reverse sensing system feature with the vehicle in P (Park), select this function from the SETUP MENU or put the vehicle in R (Reverse). 2. Press and hold the RESET control to turn the park aid ON or OFF. 3. Press the RESET control for the next SETUP MENU item or wait for more than four seconds to return to the INFO MENU. Running Boards (if equipped) This feature automatically deploys the side running boards for easy entry/exit from the vehicle or for cleaning.


104


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


1. To disable/enable the power running board feature with the vehicle in P (Park), select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the running boards setting as follows: • AUTO: the running boards will automatically deploy when a door is opened and automatically retract when the door is closed, • OUT: the running boards will remain deployed regardless of the doors being open/closed. This setting can be used when washing the vehicle, or accessing the roof rack. The running boards will stow and enter AUTO mode when the vehicle speed exceeds 5 mph (8 km/h), • OFF: the running boards will remain IN regardless of the doors being open/closed. Autolamp delay This feature keeps your headlights on for up to three minutes after the ignition is switched off. 1. To disable/enable the autolamp delay feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to select the new Autolamp delay values of >0, >10, >20, >30, >60, >90, >120 or >180. Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear, putting the vehicle in motion. 1. To disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolocks ON or OFF. Autounlock This feature automatically unlocks all vehicle doors when the driver’s door is opened within 10 minutes of the ignition being turned off.


105


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


1. To disable/enable the autounlock feature, select this function from the SETUP MENU. 2. Press and hold the RESET control switch to turn the autounlock ON or OFF. 3. Press the RESET control switch for the next SETUP MENU item. Easy Entry (if equipped) This feature automatically moves the drivers seat backwards for easy exit from the vehicle. 1. To disable/enable the easy entry/exit seat feature, select this function from the SETUP menu. 2. Press the RESET control to turn the easy entry/exit seat on or off. Trailer sway (if equipped) This feature uses the electronic stability control to mitigate trailer sway. 1. To disable/enable the trailer sway feature, select this function from the SETUP menu for the current display mode. 2. Press the RESET control to turn the trailer sway on or off. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. Language 1. Select this function from the SETUP menu for the current language to be displayed. 2. Waiting four seconds or pressing the RESET control cycles the message center through each of the language choices.


106


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Selectable languages are English, Spanish, or French. 3. Press and hold the RESET control for two seconds to set the language choice. Reset to English (if in another language) When entering the SETUP MENU and a non-English language has been selected, “HOLD RESET FOR ENGLISH” will be displayed. Press and hold the RESET control to set the language choice. System warnings System warnings alert you to possible problems or malfunctions in your vehicle’s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for four seconds. The message center will display the last selected feature if there are no more warning messages. This allows you to use the full functionality of the message center after you acknowledge the warning by pressing the RESET control and clearing the warning message. Warning messages can be divided into three categories: • Cannot be cleared until the condition is corrected. • Reappears 10 minutes after resetting it. • Reappears if the condition clears, then reoccurs within the same


ignition on/off cycle.


107


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Warning display Driver door ajar Passenger door ajar Rear left door ajar Rear right door ajar XXX miles to E fuel level low Check charging system Tire pressure sensor fault Low tire pressure Service RSC now Check fuel fill inlet Check 4x4 (if equipped) Tire pressure monitor fault Brake fluid level low Trailer brake module fault (if equipped) Oil change required XX% Oil life change soon Wiring fault on trailer (if equipped) Check rear park aid (if equipped) Trailer disconnected (if equipped)


Check brake system


108


Status The warning can return after the ignition key is turned from off to on if the condition still exists.


The warning can be reset. If the condition/problem occurs again, the message can return after being reset. The warning can return after the ignition key is turned from off to on if the condition/problem still exists.


The warning can be reset. The warning can return after the ignition key is turned from off to on if the condition/problem still exists.


The warning can be reset. The warning can return immediately after being reset if the condition/problem still exists. The warning will return 10 minutes after being reset if the condition/problem still exists. The warning can return after the ignition key is turned from off to on if the condition/problem still exists.


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Warning display Park brake engaged


Trailer sway reduce speed


Driver Controls


Status The warning can be reset. The warning can return immediately after being reset if the condition still exists. The warning will return 10 minutes after being reset if the condition/problem still exists. The warning can return after the ignition key is turned from off to on if the condition still exists. The warning can be reset. The warning can return immediately after being reset if the condition still exists. Temporary alert


For 4x4 low stop vehicle (if equipped) For 4x4 low shift to N (if equipped) To exit 4x4 low stop vehicle (if equipped) To exit 4x4 low shift to N (if equipped) Trailer connected Train left front tire Train right front tire Train right rear tire Train left rear tire Tires not trained – repeat Training complete DRIVER DOOR AJAR — Displayed when the driver door is not completely closed. PASSENGER DOOR AJAR — Displayed when the passenger door is not completely closed. REAR LEFT DOOR AJAR — Displayed when the rear left door is not completely closed. REAR RIGHT DOOR AJAR — Displayed when the rear right door is not completely closed.


109


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


XXX MILES TO E FUEL LEVEL LOW — Displayed as an early reminder of a low fuel condition. CHECK CHARGING SYSTEM — Displayed when the electrical system is not maintaining proper voltage. If you are operating electrical accessories when the engine is idling at a low speed, turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, contact your authorized dealer as soon as possible TIRE PRESSURE SENSOR FAULT — Displayed when a tire pressure sensor is malfunctioning, or your spare tire is in use. For more information on how the system operates under these conditions, refer to Understanding Your Tire Pressure Monitoring System (TPMS) in the Tires, Wheels and Loading chapter. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. LOW TIRE PRESSURE — Displayed when one or more tires on your vehicle have low tire pressure. Refer to Inflating Your Tires in the Tires, Wheels and Loading chapter. SERVICE RSC NOW — Displayed when the RSC system is not operating properly. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. CHECK FUEL FILL INLET — Displayed when the fuel fill inlet may not be properly closed. Refer to Easy Fuel™ “no cap” fuel system in the Maintenance and Specifications chapter. CHECK 4X4 (if equipped) — Displayed when a 4X4 system fault is present. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TIRE PRESSURE MONITOR FAULT — Displayed when the Tire Pressure Monitoring System is malfunctioning. If the warning stays on or continues to come on, contact your authorized dealer as soon as possible. BRAKE FLUID LEVEL LOW — Indicates the brake fluid level is low and the brake system should be inspected immediately. Refer to Brake fluid in the Maintenance and Specifications chapter. TRAILER BRAKE MODULE FAULT (if equipped) — Displayed and accompanied by a single chime, in response to faults sensed by the TBC. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. OIL CHANGE REQUIRED — Displayed when an oil change is required.


110


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


XX% OIL LIFE CHANGE SOON — Displayed when an oil change will soon be required and shows the percentage of oil life left. WIRING FAULT ON TRAILER (if equipped) — Displayed if there are certain faults in the vehicle wiring and trailer wiring/brake system. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. CHECK REAR PARK AID (if equipped) — Displayed when the transmission is in R (Reverse). Refer to Reverse sensing system in the Driving chapter. TRAILER DISCONNECTED (if equipped) — Displayed when a trailer connection becomes disconnected, either intentionally or unintentionally, and has been sensed during a given ignition cycle. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information. CHECK BRAKE SYSTEM — Displayed when a fault has been detected by the ABS module. PARK BRAKE ENGAGED — Displayed when the parking brake is engaged. TRAILER SWAY REDUCE SPEED (if equipped) — Displayed when the trailer sway control has detected trailer sway. For more information, refer to the Driving chapter for more information. FOR 4X4 LOW STOP VEHICLE (if equipped) — Displayed when 4X4 LOW is selected while the vehicle is moving. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. FOR 4X4 LOW SHIFT TO N (if equipped) — Displayed when 4X4
LOW is selected and the vehicle is stopped. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TO EXIT 4X4 LOW STOP VEHICLE (if equipped) — Displayed when 2WD is selected while the vehicle is operating in 4X4 LOW. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TO EXIT 4X4 LOW SHIFT TO N (if equipped) — Displayed when 2WD is selected while the vehicle has been stopped in 4X4 LOW. For more information, refer to Four-wheel drive (4WD) operation in the Driving chapter. TRAILER CONNECTED (if equipped) — Displayed when a correct trailer connection (a trailer with electric trailer brakes) is sensed during a given ignition cycle. Refer to Trailer towing in the Tires, Wheels and Loading chapter for more information.


111


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


TRAIN LEFT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN RIGHT FRONT TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN RIGHT REAR TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAIN LEFT REAR TIRE (if equipped) — Displayed when training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TIRES NOT TRAINED – REPEAT (if equipped) — Displayed when an error occurs while training the TPMS system. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information. TRAINING COMPLETE (if equipped) — Displayed when training of the TPMS system is complete. Refer to TPMS reset procedure in the Tires, Wheels and Loading chapter for more information.


POSITIVE RETENTION FLOOR MAT


WARNING: Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the


accelerator or the brake pedals.


Position the floor mat so that the eyelet is over the pointed end of the retention post. Make sure that the mat does not interfere with the operation of the accelerator or the brake pedal. To remove the floor mat, reverse the installation procedure.


112


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


TAILGATE LOCK (IF EQUIPPED) Your vehicle may be equipped with a tailgate lock designed to help prevent theft of the tailgate. • Insert ignition key and turn to the • Turn ignition key to the left to


right to engage lock.


unlock.


Tailgate removal Your tailgate is removable to allow more room for loading. Note: If equipped with a Reverse Camera System (RCS), do steps 1
through 3 before removing the tailgate. 1. Before removal of the tailgate, locate and disconnect the tailgate in-line connector under the pickup box on the passenger side of the vehicle near the spare tire. 2. Install a protective cap (located in the glove box) onto the in-line RCS connector that remains under the pickup box. 3. Partially lower tailgate and carefully feed tailgate harness up through the gap between the pickup box and the bumper. Place the tailgate harness out of the way under the pickup box.


113


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


4. Lower the tailgate. 5. Using a screwdriver, gently pry the spring clip (on each connector) past the head of the support screw. Disconnect cable. 6. Disconnect the other cable. 7. Lift tailgate to a 45-degree angle from horizontal. 8. Lift right side off of its hinge. 9. Lift tailgate to a 80-degree angle from horizontal. 10. Remove tailgate from left side hinge by sliding tailgate to the right. To install, follow the removal procedures in reverse order. Tailgate step (if equipped) Your vehicle may be equipped with a feature that allows easier entry into the truck bed. To open the tailgate step: 1. Flip down the tailgate. 2. Pull the yellow latch lever to the ) to release the unlock positon ( grab handle from its stowed postion and raise the handle upright until you feel it latch and see the latch ). The lever in the lock positon ( yellow lever only needs to be used when releasing the grab handle.


3. Rotate the center molding to unlatch the tailgate step and pull it towards you to extend it. 4. Flip open the step panel to widen the step. Note: To reduce risk of falling: • Operate step only when the vehicle is on level surface. • Operate step only in areas with • Always open flip panel to widen step.


sufficient lighting


114


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


• Always use grab handle when stepping up and down. • Step not intended for bare-footed use. • Keep step clean from contamination before use (e.g. snow, mud) • Keep the step load (you + load) below 350 lb. (159 kg). • Never drive with step deployed. To close the tailgate step: 1. Close the step panel, then lift and fully close the tailgate step into the tailgate. 2. Slide the latch at the bottom of the handle, then lower the handle. Note: • Fully close and latch the tailgate step before moving the vehicle. • Never drive with the step or grab handle deployed. • Replace slip resistance tape (serviceable item) if worn out. • Replace handle molding (serviceable item) if damaged. • Do not tow with grab handle or step frame.


Box side step (if equipped) Your vehicle may be equipped with a box side step that allows easier access to the truck bed. Note: Do not drive vehicle with box side step(s) in the deployed position. Note: The Box Side Step load carrying capability (1 person + cargo) is 500 lbs (227 kg). Do not exceed 500 lbs (227 kg).


115


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


To deploy the box side step, with your foot, push down on the button. The step will automatically extend out from the stowed position. Note: The box side steps may operate slower in cooler temperatures. In adverse conditions, debris such as mud, dirt, snow, ice, and salt may become trapped in the box side step mechanism, possibly causing the box side step to not deploy automatically after pressing the button. If this occurs, ensure that the button is pressed down, carefully manually pull out the box side step, wash off the debris with a high-pressure car wash wand, and re-stow the step.


To stow the box side step, with your foot, push the box side step under the truck until fully latched. Do not push on the button while stowing the box side step. Note: Do not use the box side steps to lift the vehicle when jacking. Utilize proper jacking points. Refer to Changing the tires in the Roadside Emergencies chapter.


BED EXTENDER (IF EQUIPPED) Your vehicle may be equipped with a cargo management feature in the truck bed. Note: This feature is not intended for off-road usage.


116


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


To open the bed extender into tailgate mode: 1. Pull the locking pin toward the center of the vehicle.


2. Open the latches to release the panels.


3. Rotate the panels toward the tailgate.


Repeat Steps 1–3 for the other side of the bed extender.


117


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


4. Connect the two panels, then rotate both knobs a quarter-turn clockwise to secure the panels. 5. Ensure the latch rod is inserted into the tailgate hole and the locking pins on both sides are engaged into their holes in the pick-up box. 6. Reverse steps for storage of the bed extender.


Note: When the vehicle is in motion, ensure the locking pins and knobs are fully engaged. Note: Ensure all cargo is secured. Note: When the vehicle is in motion, the tailgate load must not exceed 150 lbs. (68 kg). Note: The bed extender should always be kept in the grocery mode or stowed position with the tailgate closed when not being used for the purpose of restraining cargo in the tailgate mode.


118


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


To open the bed extender into grocery mode, follow Steps 1–4 by rotating the panels away from the tailgate. Close the tailgate.


CARGO AREA FEATURES (IF EQUIPPED)


Cargo management system (if equipped) The cargo management system consists of the Cargo rail package with the following as optional accessories: • Front header bar (if equipped) • Cross bars (if equipped) • Bed divider (if equipped) • Side mounted tool bins (if equipped)


119


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Cargo rail package: The strong extruded aluminum double channel rails and four adjustable cleats are designed to hold loads up to 600 lb (272 kg) per cleat (maximum of two cleats per rail).


• Cleat positions are adjusted by pulling the knob and turning slightly to lock open. The cleat can then be moved along the rail. Once the desired position is reached, return the knob to the horizontal position. Pull the cleat side-to-side to ensure it has locked into the next available hole location.


• To remove cleat from rail, pull the knob and turn slightly to lock open


and slide it off the end of the rail.


When installing cleat, reverse instructions above. Note: When replacing a cleat into the rail, make sure the oval embossed on the knob is not upside down. This will ensure that the cleat is properly oriented to accept accessory attachments.


120


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Front header bar: Spans the header area of the pickup box, providing the function of a header rail.


Driver Controls


• Attachment cleats from side rails or other attachments may be positioned in the front header bar to secure loads up to 600 lb (272 kg) per cleat (maximum of two cleats).


• Cleats and other attachments may be inserted through the access window located in the center of the header bar. These items can then be slid to either side, and secured the same way as the side rails.


121


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Cross bars: Aluminum cross bars with T-slot channels in all four sides, and a latch mechanism that allows the end supports to snap over the existing cleats. Cross bars are rated to hold loads up to 100 lb (45 kg) load evenly distributed between the two crossbars, and the T-slots are sized to accept industry-standard roof rack accessories.


shroud off of the cleat.


• To remove cross bar, lift handle on each side and lift end support • To install cross bar, align cleats directly across from each other on the same rail (upper or lower). Then place crossbar end support onto cleat and press down on each side until the latch handle cycles up and then press the handle down to secure (pull up on the bars to ensure they are securely attached). • To install accessories into T-slots, remove cross bar and turn upside down, then find the slip joint end, indicated with an arrow embossed on the bottom of the support. Using a T25 Torx driver, remove two Torx head bolts from bottom, and slide end support off of aluminum extrusion. Insert accessory into desired T-slot, and install end support. When tightening Torx head bolts, hand tightening with a Torx driver is sufficient, DO NOT over torque by using a ratchet.


122


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Bed divider: This panel will keep small items up to 400 lb (180 kg) in position in the pickup box. Also includes T-slots to allow attachment of industry-standard roof rack accessories.


Driver Controls


shroud off of the cleat.


• To remove bed divider, lift handle on each side and lift end support • To install bed divider, align cleats directly across from each other on the lower rail. Then place divider end support onto the cleats and press down on each side until the latch handle cycles up then press the handle down to secure (pull up on the divider to ensure they are securely attached). • To install accessories into T-slots, remove bed divider, then find the slip joint end, indicated with an arrow embossed on the support. Using a T25 Torx driver, remove two Torx head bolts and slide end support off of the aluminum extrusion. Insert accessory into desired T-slot and install end support. When tightening Torx head bolts, hand tightening with a Torx driver is sufficient, DO NOT over torque by using a ratchet.


123


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls


Side mounted tool bins: Watertight bins can be positioned at any point along the side rails and can be easily removed (even when full), and carried to wherever the contents are needed. Each bin will hold up to 60 lb (27 kg) of cargo, and has a drain plug for use as a cooler. Note: When multiple bins are placed on one side of the pickup box, the total cargo weight in all bins on that side of the pickup box cannot exceed 60 lb (27 kg).


• To access the lock, pull the tab at the base of the rubber cap to


uncover the lock. When you are done with the lock always reinstall the rubber cap on the lock to ensure proper sealing. When the bin is unlocked the rubber cap does not need to be removed to open the bin, just press the rubber cap to unlatch the lid.


• The lock cylinder is keyed to the first ignition key to be turned in the


lock. This allows one key to work all bins, even if more are ordered through the dealer. The dealer will usually key the locks during pre-delivery, but if necessary, simply remove the sticker covering the keyhole, insert ignition key and turn to the extent of travel in each direction. This key will then be the only key to unlock the bin.


• Once the key has been set, simply turn the key to the right to lock, or


to the left to unlock. When locked, the push-button will not depress when pushed.


124


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Driver Controls • To remove the bin from the rail, open lid and pull up on both levers located on the outboard edge (next to the pickup box top rail) until the handles are all the way up (approximately 90 degrees). Once both handles are raised, the lid may be closed. Note: Windows in the lid will allow the handles to stick up above the lid (with the lid closed). After closing the lid, simply lift up and inboard away from the pickup box side to release bin from rail.


• To install, reverse the above instructions. Note: Remove the bins during severe off road driving to avoid damage to the cargo bins and pickup box.


WARNING: If any levers are visible above the lid of the bin, the bin is not securely attached to the rail, and may become


detached from the vehicle if driven in that configuration.


125


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Locks and Security


KEYS The key operates all locks on your vehicle. In case of loss, replacement keys are available from your dealer. You should always carry a second key with you in a safe place in case you require it in an emergency. Refer to the SecuriLock™ passive anti-theft system section in this chapter for more information.


POWER DOOR LOCKS (IF EQUIPPED) Press control to unlock all doors.


Press control to lock all doors.


Smart unlocking feature The smart unlocking feature helps prevent you from locking yourself out of your vehicle. With the key in any ignition position: • The driver’s door will automatically unlock if it is locked by the


driver’s power lock control while the driver’s door is open.


The vehicle may still be locked with the key in the ignition, and performing one of the following actions: • Pressing the manual lock button on the door. • Operating the remote entry transmitter. • Operating the keyless entry keypad. • Operating the driver’s door with a key will only lock the driver’s door.


126


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Locks and Security


and the vehicle speed is 9 mph (15 km/h) or lower and


transmission the park brake should not be engaged) and


Autolock The autolock feature is available on vehicles with power locking. This feature will lock all the doors when: • all the doors are closed, • the ignition is in the on position, • you shift into any gear putting the vehicle in motion, (for manual • the vehicle attains a speed greater than 12 mph (20 km/h). The autolock feature repeats when: • any door is opened then closed while the ignition is in the on position • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Your vehicle comes with the autolock feature enabled. There are four methods to enable/disable this feature: • Through your authorized dealer, or • Performing the power door lock control procedure, • Performing the keyless entry keypad (if equipped) procedure, or • Performing the message center (if equipped) procedure. Power door unlock/lock procedure Before starting, ensure the ignition is in the off position and all vehicle doors are closed. You must complete Steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. Note: All doors must be closed and remain closed throughout the configuration process. 1. Turn the ignition to the on position. 2. Press the power door unlock control three times. 3. Turn the ignition from the on to the off position. 4. Press the power door unlock control three times. 5. Turn the ignition back to the on position. The horn will chirp.


127


2009 F-150 (f12) Owners Guide (own2002), 3rd Printing USA (fus)


Locks and Security


6. Press the unlock control, then press the lock control. The horn will chirp once if autolock was deactivated or twice (one short and one long chirp) if autolock was activated. 7. Turn the ignition to the off position. The horn will chirp once to confirm the procedure is complete. Keyless entry keypad procedure 1. Turn the ignition to the off position. 2. Close all doors 3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8.

Loading...
x