2016 Ford Explorer Owners Manual

Removing the Head Restraint 1. Fold the head restraint. 2. Press and hold both C buttons. 3. Pull the head restraint up. Installing the Head Restraint Align the steel stems into the guide sleeves and push the head restraint down until it locks.

142

Explorer (TUB), enUSA, First Printing

E201128E190836Seats

Recline Adjustment WARNING

Always drive and ride with your seatback upright and the lap belt snug and low across the hips.

1. Adjust the seatback to an upright

driving or riding position.

2. Pivot the head restraint forward toward

your head to the desired position. After the head restraint reaches the forward-most tilt position, pivoting it forward again will then release it to the rearward, un-tilted position. MANUAL SEATS (If Equipped) Moving the Seat Backward and Forward

WARNINGS

Do not adjust the driver seat or seatback when your vehicle is moving. Rock the seat backward and forward after releasing the lever to make sure that it is fully engaged.

143

Explorer (TUB), enUSA, First Printing

E144727E190838E190837Seats

Lumbar Adjustment (If Equipped)

POWER SEATS

WARNINGS

Do not adjust the driver seat or seatback when your vehicle is moving. Adjusting your seatback

while the vehicle is in motion may cause loss of control of the vehicle.

Do not place cargo or any objects behind the seatback before returning it to the original position.

144

Explorer (TUB), enUSA, First Printing

E190839E176038Power Lumbar (If Equipped)

Seats

Note: The engine must be running or the vehicle must be in accessory mode to activate the seats. Note: Allow a few seconds for any selection to activate. The seatback and cushion massage cannot function at the same time.

Multi-Contour Front Seats With Active Motion (If Equipped) Note: The massage system will turn off after 20 minutes.

Massage mode

Lumbar and bolster mode

Back massage intensity

adjustment

Upper lumbar

Massage intensity decrease

Lumbar decrease

and off*

Cushion massage intensity

adjustment

Lower lumbar**

Massage intensity increase

Lumbar increase

On and off

*The massage feature will default to an alternating massage mode with back massage intensity adjustment. The lumbar and bolster feature will default to the middle lumbar mode. **Press C a second time to adjust the back bolster. Press C a third time to adjust the cushion bolster.

You can also adjust this feature through the touchscreen. When switched on, the system displays directions for you to adjust the lumbar settings in your seat or to set the massage function. To access and make adjustments to the lumbar setting: 1. Press the Menu Settings icon > Vehicle

> Multi-contour Seat.

2. Choose the desired seat to adjust. 3. Press the + or - to adjust the lumbar

intensity.

145

Explorer (TUB), enUSA, First Printing

E176039E156301Seats

Saving a PreSet Position 1. Switch the ignition on. 2. Adjust the memory features to your

desired position.

3. Press and hold the desired preset button until you hear a single tone.

You can save up to three preset memory positions. You can save a memory preset at any time. Recalling a PreSet Position Press and release the preset button associated with your desired driving position. The memory features move to the position stored for that preset. Note: You can only recall a preset memory position when the ignition is off, or when the transmission is in park (P) or neutral (N) (and your vehicle is not moving) if the ignition is on. You can also recall a preset memory position by: • Pressing the unlock button on your

intelligent access key fob if it is linked to a preset position.

• Unlocking the intelligent driver door handle if a linked key fob is present. Entering a personal entry code on the Securicode keypad. See Locks (page 60).

•

Note: Using a linked key fob to recall your memory position when the ignition is off moves the seat to the Easy Entry position. Note: Pressing any active memory feature adjustment control (or any memory button) during a memory recall cancels the operation.

To access and make adjustments to the massage setting: 1. Press the Menu Settings icon > Vehicle

>Multi-contour Seat.

2. Choose the desired seat to adjust. 3. Press Off, Lo or Hi. MEMORY FUNCTION (If Equipped)

WARNINGS

Before activating the seat memory, make sure that the area immediately surrounding the seat is clear of

obstructions and that all occupants are clear of moving parts.

Do not use the memory function when your vehicle is moving.

This feature automatically recalls the position of the following: • Driver seat. • Power mirrors. • Optional power adjustable foot pedals. • Optional steering column. The memory control is located on the driver door.

146

Explorer (TUB), enUSA, First Printing

E142554Seats

Linking a PreSet Position to your Remote Control or Intelligent Access Key Fob Your vehicle can save the preset memory positions for up to three remote controls or intelligent access (IA) keys. 1. With the ignition on, move the memory

positions to the desired positions. 2. Press and hold the desired preset

button for about five seconds. A tone sounds after about two seconds. Continue holding until you hear a second tone.

REAR SEATS Adjusting the Rear Seats Second Row Seats

WARNINGS

Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’s safety belt, resulting in severe

personal injuries in the event of a crash.

3. Within three seconds, press the lock button on the remote control you are linking.

To unlink a remote control, follow the same procedure – except in step 3, press the unlock button on the remote control. Note: If more than one linked remote control or intelligent access key is in range, the memory function moves to the settings of the first key to recall a memory position. Easy Entry and Exit Feature If you enable the easy entry and exit feature, it automatically moves the driver seat position rearward up to two inches (five centimeters) when you switch the ignition off. The driver seat returns to the previous position when you switch the ignition on. You can enable or disable this feature in the information display. See Information Displays (page 101).

Recline Adjustment

Lift the handle to adjust the seatback rearward or forward. The seatback can also fold forward until it is flat. Fold flat seatback

147

Explorer (TUB), enUSA, First Printing

E190840E190841Seats

Lift the handle and fold the seatback forward until it is flat. Note: For the bench seats, make sure the center safety belt is unbuckled before folding the seatback. Moving the Seats Backward and Forward (If equipped)

Note: Remove items from the second-row seat. Make sure that no bulky objects such as purses or briefcases are on the floor in front of the second-row seats before tumbling them. Note: For second-row bench seats, make sure the center safety belt is unbuckled before folding the seatback. Note: You may have to move the front-row seat forward to allow the second-row seat to be fully tumbled. Note: You may have to lower the center head restraint. See Head Restraints (page 140). Fold and tumble the second-row seat to access the third row:

Third Row Seats (Manual Seats)

WARNINGS

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original position, pull on the seatback to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash.

Do not adjust or release the seat floor latch while vehicle is in motion. Do not operate the vehicle with seats in the tumbled position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched or if the seat is tumbled, the seat may cause injury during a sudden stop.

Explorer (TUB), enUSA, First Printing

1. Fold the outboard head restraint.

2. Lift the handle located on the side of

the seat to fold the seatback flat.

148

E190838E193964E190843Seats

5. Lift the seatback toward the rear of the vehicle, and rotate the seatback until you hear a click, locking it in the upright position. Note: The seatback will not raise if the rear latch hooks are not properly engaged to the floor striker. If the seatback does not raise, then repeat Step 4.

6. Pull the head restraint back up to its

normal adjusted position.

3. Lift the handle all the way up until the seat releases from the floor. Rotate the seat forward to allow access to the third row.

4. To return the seatback to the floor from the tumbled position, rotate the seat down until you hear it latching to the floor.

149

Explorer (TUB), enUSA, First Printing

Make sure that the rear latch hooks are properly engaged with the floor striker. Note: Make sure that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement. Third Row Seat Access (Power Fold and Tumble Seat-If equipped)

WARNING

Make sure that the seat is unoccupied when folding it down. Folding the seat while occupied

could result in occupant injury or damage to the seat.

E190844E190845E190846E190847Seats

The control is located at the back of the rear door opening. Press and hold it to fold the seatback down and tumble the seat forward for access to the third row. Third Row Seat Exit (Manual Seat, Power Fold and Tumble Seat)

1. Fold the outboard head restraint.

2. Pull on the strap located on the back of the second row seat. This will fold the seatback forward. Pull the strap a second time to tumble the seat forward, allowing easy exit from the third row seat.

WARNINGS

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original position, pull on the seatback to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash.

Do not adjust or release the seat floor latch while vehicle is in motion. Do not operate the vehicle with seats in the tumbled position. Always latch the vehicle seat to the floor, whether the seat is occupied or empty. If not latched or if the seat is tumbled, the seat may cause injury during a sudden stop.

Note: You may have to lower the center head restraint. See Head Restraints (page 140).

150

Explorer (TUB), enUSA, First Printing

E190848E193964E190849E190850Seats

3. To return the seatback to the floor from the tumbled position, rotate the seat down until you hear it latching to the floor.

Folding the Third Row Manual Seat 1. Remove all objects from the seat and

stowage tub.

2. Fold the outboard head restraint by

pulling the head restraint release strap.

4. Lift the seatback toward the rear of the vehicle, and rotate the seatback until you hear a click, locking it in the upright position. Note: The seatback will not raise if the rear latch hooks are not properly engaged to the floor striker. If the seatback does not raise, then repeat Step 3.

5. Pull the head restraint back up to its

normal adjusted position.

3. From the rear of the vehicle, fold the

seatback by pulling and holding the red strap while pushing the seatback forward. Release the strap once the seatback starts rotating forward.

Make sure that the rear latch hooks are properly engaged with the floor striker. Note: Make sure that the seat and seatback are latched securely in position. Keep floor area free of objects that would prevent proper seat engagement.

151

Explorer (TUB), enUSA, First Printing

E190846E190847E193843E190854Seats

WARNINGS

Before returning the seatback to its original position, make sure that cargo or any objects are not trapped

behind the seatback. After returning the seatback to its original position, pull on the seatback to make sure that it has fully latched. An unlatched seat may become dangerous in the event of a sudden stop or crash.

4. Release the cushion latches by pulling the short black strap while pulling on the strap located at the top of the seatback to tumble the seat all the way into the tub in the floor.

Note: Do not use the seat anchors as cargo tie downs.

Do not drive the vehicle when the third-row seat is rotated backwards. During a sudden stop, the safety

belts are not functional in this position and the third-row seat can rapidly tip back to the forward position, all of which may result in serious injury.

Note: Do not use the third row seat back as a load floor when the seatback is folded. Note: Make sure that the area under the seat is free of objects before stowing it. Unfolding the Third Row Manual Seat

Note: Make sure that there are no objects such as books, purses or briefcases on the load floor before unstowing the seat. Failure to remove all objects from the top of the load floor prior to unstowing it may cause damage to the seat. Note: Make sure the area under the load floor is free of objects before unstowing it.

WARNINGS

Make sure seat is latched to vehicle floor by pushing and pulling on the seat. If not latched, the seat may

cause injury during a sudden stop.

152

Explorer (TUB), enUSA, First Printing

E190923E190924E190927Seats

1. Unlatch and lift the seat out of the tub in the floor by squeezing and pulling up on the handle. Once the seat is at a vertical position, push the seat over, letting it fall onto the latches.

2. To return the seatback to the upright position, pull the red strap. Then while holding the red strap, pull the long strap located on the seatback to raise the seatback.

3. Pull the head restraints up to their

normal positions.

PowerFold™Third Row Seats (If equipped) The third row power seat buttons are located behind the third row seats on the left-hand quarter trim panel.

NORMAL: Press to return the seat to the normal seating position. STOW: Press to stow the seat into the tub floor.

153

Explorer (TUB), enUSA, First Printing

E190925E190926E190928Seats

FOLD: Press to fold down the seatback. RH / BOTH / LH: Press to select the normal, stow and fold modes to activate the right-hand seat, the left-hand seat or both.

HEATED SEATS (If Equipped) Front Seats

WARNING

People who are unable to feel pain to their skin because of advanced age, chronic illness, diabetes, spinal

cord injury, medication, alcohol use, exhaustion or other physical conditions, must exercise care when using the heated seat. The heated seat may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion. This may cause the heated seat to overheat. Do not puncture the seat with pins, needles or other pointed objects. This may damage the heating element which may cause the heated seat to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the heated seat if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

Note: The third row seat includes obstacle detection that allows the seat to stop and reverse direction if it hits an obstacle so that the obstacle can be removed. Note: Pressing a different button while the power seat feature is already being performed may cause the first selected seat movement to be cancelled. Allow the first seat movement to be completed before pressing a button for another function. Note: Make sure that there are no objects such as books, purses or briefcases on the load floor before unstowing the seat. Failure to remove all objects from the top of the load floor prior to unstowing it may cause damage to the seat. Note: In order to allow the seat to complete the stowed position, do not place objects under the seat before stowing. Remove all objects from the seat and stowage tub. Note: In the unlikely event that the third row power seat stops prematurely or travels to an unexpected position, press the FOLD button (C) to reset the seat and return it to a normal position. These seats feature a power one-touch operation that allows you fold and stow the seats. •

The power fold seats work only when the transmission is in park (P) and the liftgate is open. If the ignition is off and the feature is still running, the battery saver will turn it off after 10 minutes. Press unlock on the remote entry key transmitter to reactivate the power seats or unlock it with the keyless entry keypad. See Remote Control (page 49).

•

154

Explorer (TUB), enUSA, First Printing

Seats

The rear seat heat controls are located on the rear of the center console.

Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. The heated seat module resets at every ignition run cycle. While the ignition is on, press the high or low heated seat switch to enable heating mode. When activated, they will turn off automatically when you turn the engine off. CLIMATE CONTROLLED SEATS (If Equipped) Heated Seats

Press the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings. Rear Seats (If Equipped)

WARNING

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Do not do the following: • Place heavy objects on the seat. • Operate the seat heater if water or any other liquid is spilled on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

155

Explorer (TUB), enUSA, First Printing

E146322E146322Seats

WARNING

Persons who are unable to feel pain to the skin because of advanced age, chronic illness, diabetes, spinal cord injury, medication, alcohol use, exhaustion, or other physical conditions, must exercise care when using the seat heater. The seat heater may cause burns even at low temperatures, especially if used for long periods of time. Do not place anything on the seat that insulates against heat, such as a blanket or cushion, because this may cause the seat heater to overheat. Do not puncture the seat with pins, needles, or other pointed objects because this may damage the heating element which may cause the seat heater to overheat. An overheated seat may cause serious personal injury.

Note: Do not do the following: • Place heavy objects on the seat. • Operate the seat heater if water or any other liquid spills on the seat. Allow the seat to dry thoroughly.

• Operate the heated seats unless the engine is running. Doing so can cause the battery to lose charge.

Cooled Seats The cooled seats only function when the engine is running.

To operate the cooled seats: Touch the cooled seat symbol to cycle through the various cooling settings and off. More indicator lights indicate cooler settings. If the engine falls below 350 RPM while the cooled seats are on, the feature turns itself off. You need to reactivate it. Climate controlled seat air filter replacement Your vehicle is equipped with lifetime air filters that are integrated with the seats. Regular maintenance or replacement is not needed.

Touch the heated seat symbol to cycle through the various heat settings and off. More indicator lights indicate warmer settings.

156

Explorer (TUB), enUSA, First Printing

E146322E146309Universal Garage Door Opener (If Equipped)

HomeLink Wireless Control System

WARNINGS

Make sure that the garage door and security device are free from obstruction when you are

programming. Do not program the system with the vehicle in the garage.

Do not use the system with any garage door opener that does not have the safety stop and reverse

feature as required by U.S. Federal Safety Standards (this includes any garage door opener manufactured before April 1, 1982). A garage door opener which cannot detect an object, signaling the door to stop and reverse, does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death.

Note: Make sure you keep the original remote control transmitter for use in other vehicles as well as for future system programming. Note: We recommend that upon the sale or lease termination of your vehicle, you erase the programmed function buttons for security reasons. See Erasing the Function Button Codes. Note: You can program a maximum of three devices. To change or replace any of the three devices after it has been initially programmed, you must first erase the current settings. See Erasing the Function Button Codes.

The universal garage door opener replaces the common hand-held garage door opener with a three-button transmitter that is integrated into the driver’s sun visor. The system includes two primary features, a garage door opener and a platform for remote activation of devices within the home. As well as being programmed for garage doors, the system transmitter can be programmed to operate entry gate operators, security systems, entry door locks and home or office lighting. Additional system information can be found online at www.homelink.com, www.youtube.com/HomeLinkGentex or by calling the toll-free help line on 1-800-355-3515. In-Vehicle Programming This process is to program your hand-held transmitter and your in-vehicle HomeLink button. Note: The programming steps below assume you will be programming HomeLink that was not previously programmed. Note: Put a new battery in the hand-held transmitter. This will ensure quicker training and accurate transmission of the radio-frequency signal.

157

Explorer (TUB), enUSA, First Printing

E142657Universal Garage Door Opener (If Equipped)

To program additional buttons, repeat Steps 1 – 4. For questions or comments, please contact HomeLink at www.homelink.com, www.youtube.com/HomeLinkGentex or 1-800-355-3515. Programming Your Garage Door Opener Motor Note: You may need a ladder to reach the unit and you may need to remove the cover or lamp lens on your garage door opener.

1. Press the learn button on the garage

door opener motor and then you have 30 seconds to complete the next two steps.

2. Return to your vehicle.

3. Press and hold the function button you

want to program for 2 seconds, then release. Repeat this step. Depending on your brand of garage door opener, you may need to repeat this sequence a third time.

1. With your vehicle parked outside of the

garage, turn your ignition to the on position, but do not start your vehicle.

2. Hold your hand-held garage door

transmitter 2–6 in (5–14 cm) away from the HomeLink button you want to program.

3. Using both hands, simultaneously,

press and hold the desired HomeLink button and the hand-held transmitter button. DO NOT release either one until the HomeLink indicator light flashes slowly and then rapidly. When the indicator light flashes rapidly, both buttons may be released. The rapid flashing indicates successful training.

Note: You may need to use a different method if you live in Canada or have difficulties programming your gate operator or garage door opener. See Gate Operator / Canadian Programming. 4. Press and hold the HomeLink button you programmed for two seconds, then release. You may need to do this twice to activate the door. If your garage door does not operate, watch the HomeLink indicator light.

If the indicator light stays on, the programming is complete. No further action is needed. If the indicator light flashes rapidly for 2
seconds and then turns to a constant light, the HomeLink button is not programmed yet. See Programming Your Garage Door Opener Motor.

158

Explorer (TUB), enUSA, First Printing

E142658E142659E142658Universal Garage Door Opener (If Equipped)

Gate Operator / Canadian Programming Canadian radio-frequency laws require transmitter signals to “time-out” (or quit) after several seconds of transmission – which may not be long enough for HomeLink to pick up the signal during programming. Similar to this Canadian law, some U.S. gate operators are designed to “time-out” in the same manner. Note: If programming a garage door opener or gate operator, it is advised to unplug the device during the “cycling” process to prevent possible overheating. 1. Press and hold the HomeLink button while you press and release,every two seconds, your hand-held transmitter until the HomeLink indicator light changes from a slow to a rapidly blinking light.

2. Release both the HomeLink and hand-held transmitter buttons.

3. Continue programing HomeLink. See

In-Vehicle Programming.

Erasing the Function Button Codes Note: You cannot erase individual buttons.

1. Press and hold the outer two function

buttons simultaneously for approximately 20 seconds until the indicator lights above the buttons flash rapidly.

2. When the indicator lights flash, release the buttons. The codes for all buttons are erased.

Reprogramming a Single Button To program a device to a previously trained button, follow these steps: 1. Press and hold the desired button. Do

NOT release the button.

2. The indicator light will begin to flash

after 20 seconds. Without releasing the button, follow Step 1 in the Programming section.

For questions or comments, contact HomeLink at www.homelink.com, www.youtube.com/HomeLinkGentex or 1-800-355-3515. Programming to a Genie Intellicode 2
Garage Door Opener Note: The Genie Intellicode 2 transmitter must already be programmed to operate with the garage door opener. Note: To program HomeLink to the transmitter you must first put the transmitter into programming mode.

159

Explorer (TUB), enUSA, First Printing

E142660Universal Garage Door Opener (If Equipped)

1. Press and hold the previously

programmed Genie button on the hand-held transmitter for 10 seconds. The indicator light will change from red to red and green.

2. Press the same button twice to confirm

the change. If done correctly the indicator light will turn green.

Programming HomeLink to the Genie Intellicode Garage Door Opener Motor Note: You may need a ladder to access the garage door opener motor.

1. Press and hold the program button on

the garage door opener motor until both blue indicator lights turn on.

2. Release the program button. Only the smaller round indicator light should be on.

3. Press and release the program button.

The larger purple indicator light will flash.

Note: The next two steps must be completed in 30 seconds. 4. Press and release the Genie Intellicode

2 hand-held transmitter’s previously programmed button. Both indicator lights on the garage door opener motor unit should now flash purple.

A. B.

Red indicator light Green indicator light

1. Press and hold one of the buttons on

the hand-held transmitter for 10
seconds. The indicator light will change from green to red and green.

2. Press the same button twice to confirm the change to programming mode. If done properly the indicator light will appear red.

3. Hold the transmitter within 1–3 inches (2–8 centimeters) of the button on the visor you want to program.

4. Press and hold both the programmed

Genie button on the hand-held transmitter and the button you want to program. The indicator light on the visor will flash rapidly when the programming is successful.

Note: The Genie transmitter will transmit for up to 30 seconds. If HomeLink does not program within 30 seconds the Genie transmitter will need to be pressed again. If the Genie transmitter indicator light displays green and red, release the button until the indicator light turns off before pressing the button again. Once HomeLink has been programmed successfully, the Genie transmitter must be changed out of program mode. To do this:

160

Explorer (TUB), enUSA, First Printing

BAE142661E142662Universal Garage Door Opener (If Equipped)

5. Press and hold the previously

programmed button on the visor for 2
seconds. Repeat this step up to 3 times until the garage door moves. Programming is now complete. Clearing a HomeLink Device To erase programming from the three HomeLink buttons press and hold the two outer HomeLink buttons until the indicator light begins to flash. The indicator light will begin flashing in 10 to 20 seconds, at which time both buttons should be released. Programming has now been erased, and the indicator light should blink slowly to indicate the device is in train mode when any of the three HomeLink buttons are pressed. FCC and RSS-210 Industry Canada Compliance This device complies with Part 15 of the FCC Rules and with RSS-210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to your device not expressly approved by the party responsible for compliance can void the user’s authority to operate the equipment.

161

Explorer (TUB), enUSA, First Printing

Auxiliary Power Points

12 Volt DC Power Point WARNINGS

Do not plug optional electrical accessories into the cigar lighter socket. Incorrect use of the cigar

lighter can cause damage not covered by the vehicle warranty, and can result in fire or serious injury.

Do not use a power point for operating a cigar lighter. Incorrect use of the power points can cause

damage not covered by the vehicle warranty, and can result in fire or serious injury.

Note: When you switch the ignition on, you can use the socket to power 12 volt appliances with a maximum current rating of 15 amps. If the power supply does not work after you switch the ignition off, switch the ignition on. Note: Do not hang any accessory from the accessory plug. Note: Do not use the power point over the vehicle capacity of 12 volt DC 180 watts or a fuse may blow. Note: Always keep the power point caps closed when not in use. Do not insert objects other than an accessory plug into the power point. This will damage the power point and blow the fuse. Run the vehicle for full capacity use of the power point. To prevent the battery from running out of charge: • Do not use the power point longer than

necessary when the vehicle is not running.

• Do not leave devices plugged in

overnight or when you park your vehicle for extended periods.

Explorer (TUB), enUSA, First Printing

Locations Power points may be in the following locations: • On the lower instrument panel. • • On the rear of the center console. • 110 Volt AC Power Point (If Equipped)

Inside the center console.

In the rear cargo area.

WARNING

Do not keep electrical devices plugged in the power point whenever the device is not in use. Do not use any extension cord with the 110 volt AC power point, since it will defeat the safety protection design. Doing so may cause the power point to overload due to powering multiple devices that can reach beyond the 150 watt load limit and could result in fire or serious injury.

Note: The power point will turn off when the ignition is switched off or the battery voltage drops below 11 volts. Use the power point for powering electric devices that require up to 150 watts. It is on the rear of the center console.

Note: Depending on your vehicle, the power point cover may open to the right or upward.

162

E193395Auxiliary Power Points

When the indicator light on the power point is: • On: The power point is working, the ignition is on and a device is plugged in.

• Off: The power point is off, the ignition

is off or no device is plugged in. Flashing: The power point is in fault mode.

•

The power outlet temporarily turns off power when in fault mode if the device exceeds the 150 watt limit. Unplug your device and switch the ignition off. Switch the ignition back on, but do not plug your device back in. Let the system cool off and switch the ignition off to reset the fault mode. Switch the ignition back on and make sure the indicator light remains on. Do not use the power point for certain electric devices, including: • Cathode-ray, tube-type televisions. • Motor loads, such as vacuum cleaners, electric saws and other electric power tools or compressor-driven refrigerators.

• Measuring devices, which process

precise data, such as medical equipment or measuring equipment.

• Other appliances requiring an

extremely stable power supply such as microcomputer-controlled electric blankets or touch-sensor lamps.

163

Explorer (TUB), enUSA, First Printing

Storage Compartments

CENTER CONSOLE Stow items in the cup holder carefully as items may become loose during hard braking, acceleration or crashes, including hot drinks which may spill. Available console features include:

Rear Seat Armrest

OVERHEAD CONSOLE

Press near the rear edge of the door to open it.

USB, or USB and SD card (if equipped). Power point. Cup holder. Hill descent control (if equipped). 110 volt AC power point or USB port (if equipped). Rear climate controls (if equipped). 110 volt AC power point / 230
volt AC power point (if equipped). USB smart charger (if equipped).

164

Explorer (TUB), enUSA, First Printing

E193409E190042E75193Starting and Stopping the Engine

GENERAL INFORMATION

IGNITION SWITCH (If Equipped)

WARNINGS

Extended idling at high engine speeds can produce very high temperatures in the engine and

exhaust system, creating the risk of fire or other damage.

Do not park, idle or drive your vehicle on dry grass or other dry ground cover. The emission system heats up

the engine compartment and exhaust system, creating the risk of fire.

Do not start the engine in a closed garage or in other enclosed areas. Exhaust fumes can be toxic. Always open the garage door before you start the engine.

If you smell exhaust fumes inside your vehicle, have your vehicle checked by an authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes.

If you disconnect the battery, your vehicle may exhibit some unusual driving characteristics for approximately 5 miles (8 kilometers) after you reconnect it. This is because the engine management system must realign itself with the engine. You can disregard any unusual driving characteristics during this period. The powertrain control system meets all Canadian interference-causing equipment standard requirements regulating the impulse electrical field or radio noise. When you start the engine, avoid pressing the accelerator pedal before and during operation. Only use the accelerator pedal when you have difficulty starting the engine.

0 (off) - The ignition is off. Note: When you switch the ignition off and leave your vehicle, do not leave your key in the ignition. This could cause your vehicle battery to lose charge. I (accessory) - Allows the electrical accessories, such as the radio, to operate while the engine is not running. Note: Do not leave the ignition key in this position for too long. This could cause your vehicle battery to lose charge. II (on) - All electrical circuits are operational and the warning lamps and indicators illuminate. III (start) - cranks the engine. KEYLESS STARTING (If Equipped) Note: The keyless starting system may not function if the key is close to metal objects or electronic devices such as cellular phones. Note: A valid key must be located inside your vehicle to switch the ignition on and start the engine.

165

Explorer (TUB), enUSA, First Printing

E72128Starting and Stopping the Engine

Note: You can crank the engine for a total of 60 seconds without the engine starting before the starting system temporarily disables. The 60 seconds does not have to be all at once. For example, if you crank the engine three times for 20 seconds each time, without the engine starting, you reached the 60-second time limit. A message appears in the information display alerting you that you exceeded the cranking time. You cannot attempt to start the engine for at least 15 minutes. After 15
minutes, you are limited to a 15-second engine cranking time. You need to wait 60
minutes before you can crank the engine for 60 seconds again. Before starting your vehicle, check the following: • Make sure all occupants have fastened

their safety belts.

• Make sure the headlamps and electrical accessories are off.

• Make sure the parking brake is on. • Make sure the transmission is in park

(P). Switch the ignition on. For vehicles with a keyless ignition, see the following instructions.

•

Vehicles with an Ignition Key Note: Do not touch the accelerator pedal. 1. Fully depress the brake pedal. 2. Turn the key to the start position to

start the engine.

Note: The engine may continue cranking for up to 15 seconds or until it starts. Note: If you cannot start the engine on the first try, wait for a short period and try again. Vehicles with Keyless Start Note: Do not touch the accelerator pedal.

Ignition Modes

The keyless starting system has three modes: Off: Turns the ignition off. • Without applying the brake pedal, press and release the button once when the ignition is in the on mode, or when the engine is running but the vehicle is not moving.

On: All electrical circuits are operational and the warning lamps and indicators illuminate. • Without applying the brake pedal, press and release the button once.

Start: Starts the vehicle. The engine may not start when the vehicle starts. • Press the brake pedal, and then press the button for any length of time. An indicator light on the button illuminates when then ignition is on and when the engine starts.

STARTING A GASOLINE ENGINE When you start the engine, the idle speed increases. This helps to warm up the engine. If the engine idle speed does not slow down automatically, have your vehicle checked by an authorized dealer.

166

Explorer (TUB), enUSA, First Printing

E144447Starting and Stopping the Engine

Note: You must have your intelligent access key in your vehicle in order to shift the transmission out of park (P). 1. Fully depress the brake pedal. 2. Press the push button ignition switch. The system does not function if: •

The passive key frequencies are jammed. The key battery has no charge.

• If you are unable to start your vehicle, do the following:

2.

Insert the passive key into the backup slot.

3. With the key in this position, press the brake pedal then press the push button ignition switch to switch the ignition on and start your vehicle.

Fast Restart The fast restart feature allows you to restart your vehicle within 20 seconds of switching it off, even if it does not detect a valid passive key. Within 20 seconds of switching the engine off, press the brake pedal and press the push button ignition switch. After 20
seconds, you can no longer start your vehicle if it does not detect a valid passive key. Once your vehicle starts, it remains running until you press the push button ignition switch, even if your vehicle does not detect a valid passive key. If you open and close a door while your vehicle is running, the system searches for a valid passive key. You cannot start your vehicle if the system does not detect a valid passive key within 20 seconds. Failure to Start If you cannot start the engine after three attempts, wait 10 seconds and follow this procedure: 1. Fully depress the brake pedal. 2. Shift into park (P). 3. Fully depress the accelerator pedal and

hold it there.

4. Start the engine.

1. Open the floor console storage

compartment lid.

167

Explorer (TUB), enUSA, First Printing

1E1987282Starting and Stopping the Engine

2. Switch the ignition off. 3. Apply the parking brake. Vehicles with Keyless Start 1. Shift into park (P). 2. Press the push button ignition switch. 3. Apply the parking brake. Note: The ignition, all electrical circuits and all warning lamps and indicators will be turned off. Note: If the engine is idling for 30 minutes, the ignition and engine automatically shut down. Stopping the Engine When Your Vehicle is Moving

WARNING

Switching off the engine when the vehicle is still moving will result in a loss of brake and steering assistance. The steering will not lock, but higher effort will be required. When the ignition is switched off, some electrical circuits, including air bags, warning lamps and indicators may also be off. If the ignition was turned off accidentally, you can shift into neutral (N) and re-start the engine.

Vehicles with an Ignition Key 1. Shift into neutral and use the brakes to

bring your vehicle to a safe stop.

2. When your vehicle has stopped, shift into park (P) and switch the ignition off.

3. Apply the parking brake. Vehicles with Keyless Start 1. Shift into neutral and use the brakes to

bring your vehicle to a safe stop.

2. When your vehicle has stopped, shift

into park (P).

Automatic Engine Shutdown For vehicles with a keyless ignition, this feature automatically shuts down the engine if it has been idling for an extended period. The ignition also turns off in order to save battery power. Before your vehicle shuts down, a message appears in the information display showing a timer counting down from 30 seconds. If you do not intervene within 30 seconds, your vehicle shuts down. Another message appears in the information display to inform you that your vehicle has shut down to save fuel. Start your vehicle as you normally do. Automatic Engine Shutdown Override Note: You cannot permanently switch off the automatic shutdown feature. When you switch it off temporarily, it turns on at the next ignition cycle. You can stop the shutdown, or reset the timer, at any point before the 30-second countdown has expired by doing any of the following: •

You can reset the timer by interacting with your vehicle, for example pressing the brake or accelerator pedal. You can temporarily switch off the shutdown feature any time the ignition is on using the information display. See Information Displays (page 101). The feature only remains off for the current ignition cycle.

•

• During the 30-second countdown, the

system prompts you to press OK or RESET to temporarily switch the feature off for the current ignition cycle only.

Stopping the Engine When Your Vehicle is Stationary Vehicles with an Ignition Key 1. Shift into park (P).

168

Explorer (TUB), enUSA, First Printing

Starting and Stopping the Engine

Note: The heater is most effective when outdoor temperatures are below 0°F (-18°C). The heater acts as a starting aid by warming the engine coolant. This allows the climate control system to respond quickly. The equipment includes a heater element (installed in the engine block) and a wire harness. You can connect the system to a grounded 120-volt AC electrical source. We recommend that you do the following for a safe and correct operation: • Use a 16-gauge outdoor extension cord

that is product certified by Underwriter’s Laboratory (UL) or Canadian Standards Association (CSA). This extension cord must be suitable for use outdoors, in cold temperatures, and be clearly marked Suitable for Use with Outdoor Appliances. Do not use an indoor extension cord outdoors. This could result in an electric shock or become a fire hazard.

• Use as short an extension cord as

possible.

• Do not use multiple extension cords. • Make sure that when in operation, the

extension cord plug and heater cord plug connections are free and clear of water. This could cause an electric shock or fire.

• Make sure your vehicle is parked in a

clean area, clear of combustibles.

• Make sure the heater, heater cord and extension cord are firmly connected.

• Check for heat anywhere in the

electrical hookup once the system has been operating for approximately 30
minutes.

3. Press and hold the push button ignition

switch, or press it three times within two seconds.

4. Apply the parking brake. Guarding Against Exhaust Fumes

WARNING

If you smell exhaust fumes inside your vehicle, have your vehicle checked by your authorized dealer immediately. Do not drive your vehicle if you smell exhaust fumes. Carbon monoxide is present in exhaust fumes. Take precautions to avoid its dangerous effects. Important Ventilating Information If you stop your vehicle and then leave the engine idling for long periods, we recommend that you do one of the following: • Open the windows at least 1 in (3 cm). • Set your climate control to outside air. ENGINE BLOCK HEATER (If Equipped)

WARNINGS

Failure to follow engine block heater instructions could result in property damage or serious personal injury. Do not use your heater with ungrounded electrical systems or two-pronged adapters. There is a risk

of electrical shock.

Do not fully close the hood, or allow it to drop under its own weight when using the engine block heater. This could damage the power cable and may cause an electrical short resulting in fire, injury and property damage.

169

Explorer (TUB), enUSA, First Printing

Starting and Stopping the Engine

• Make sure the system is unplugged and

properly stowed before starting and driving your vehicle. Make sure the protective cover seals the prongs of the block heater cord plug when not in use.

• Make sure the heater system is

checked for proper operation before winter.

Using the Engine Block Heater Make sure the receptacle terminals are clean and dry prior to use. Clean them with a dry cloth if necessary. The heater uses 0.4 to 1.0 kilowatt-hours of energy per hour of use. The system does not have a thermostat. It achieves maximum temperature after approximately three hours of operation. Using the heater longer than three hours does not improve system performance and unnecessarily uses electricity.

170

Explorer (TUB), enUSA, First Printing

Fuel and Refueling

SAFETY PRECAUTIONS

WARNINGS

Do not overfill the fuel tank. The pressure in an overfilled tank may cause leakage and lead to fuel spray

and fire.

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door (Easy Fuel capless fuel system), do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

Automotive fuels can cause serious injury or death if misused or mishandled. Flow of fuel through a fuel pump nozzle can produce static electricity. This can cause a fire if you are filling

an ungrounded fuel container.

Fuel ethanol and gasoline may contain benzene, which is a cancer-causing agent. When refueling always shut the engine off and never allow sparks or open flames near the filler neck. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

Observe the following guidelines when handling automotive fuel: •

Extinguish all smoking materials and any open flames before refueling your vehicle.

• Always turn off the vehicle before

refueling.

Explorer (TUB), enUSA, First Printing

• Automotive fuels can be harmful or

fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury. If fuel is swallowed, call a physician immediately, even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours.

• Avoid inhaling fuel vapors. Inhaling too much fuel vapor of any kind can lead to eye and respiratory tract irritation. In severe cases, excessive or prolonged breathing of fuel vapor can cause serious illness and permanent injury.

• Avoid getting fuel liquid in your eyes. If

fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury. Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin, clothing or both, promptly remove contaminated clothing and wash skin thoroughly with soap and water. Repeated or prolonged skin contact with fuel liquid or vapor causes skin irritation. Be particularly careful if you are taking “Antabuse” or other forms of disulfiram for the treatment of alcoholism. Breathing gasoline vapors, or skin contact could cause an adverse reaction. In sensitive individuals, serious personal injury or sickness may result. If fuel is splashed on the skin, promptly wash skin thoroughly with soap and water. Consult a physician immediately if you experience an adverse reaction.

•

•

171

Fuel and Refueling

•

•

Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT). Leaded fuel (using leaded fuel is prohibited by law).

The use of fuels with metallic compounds such as methylcyclopentadienyl manganese tricarbonyl (commonly known as MMT), which is a manganese-based fuel additive, will impair engine performance and affect the emission control system. Do not be concerned if the engine sometimes knocks lightly. However, if the engine knocks heavily while using fuel with the recommended octane rating, contact an authorized dealer to prevent any engine damage. FUEL QUALITY - E85
Choosing the Right Fuel

Use regular unleaded gasoline with a minimum pump (R+M)/2 octane rating of 87, or regular unleaded gasoline blended with a maximum of 85% ethanol (E85). Flex fuel vehicles have a yellow fuel filler cap or the fuel tank filler pipe will have a yellow housing or bezel. Some fuel stations offer fuels posted as regular unleaded gasoline with an octane rating below 87, particularly in high altitude areas. Fuels with octane levels below 87 are not recommended.

FUEL QUALITY Choosing the Right Fuel

We recommend regular unleaded gasoline with a pump (R+M)/2 octane rating of 87. Some fuel stations offer fuels posted as regular unleaded gasoline with an octane rating below 87, particularly in high altitude areas. We do not recommend fuels with an octane rating below 87. For vehicles with EcoBoost engines, to provide improved performance, we recommend premium fuel for severe duty usage such as trailer tow. Do not use any fuel other than those recommended because they could lead to engine damage that may not be covered by the vehicle Warranty. Note: Use of any fuel other than those recommended can impair the emission control system and cause a loss of vehicle performance. Do not use: • Diesel fuel. • •

Fuels containing kerosene or paraffin. Fuel containing more than 15% ethanol or E85 fuel. Fuels containing methanol. Fuels containing metallic-based additives, including manganese-based compounds.

• •

172

Explorer (TUB), enUSA, First Printing

E161513E161513Fuel and Refueling

RUNNING OUT OF FUEL Running out of fuel can cause damage not covered by the vehicle Warranty. If your vehicle runs out of fuel: • Add a minimum of 1.3 gal (5 L) of fuel to restart the engine. If your vehicle is out of fuel and on a steep slope, more fuel may be required. You may need to switch the ignition from off to on several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. When restarting, cranking time takes a few seconds longer than normal.

•

Filling a Portable Fuel Container Use the following guidelines to avoid electrostatic charge build-up when filling an ungrounded fuel container: • Only use an approved fuel container to transfer fuel to your vehicle. Place the container on the ground when filling it.

•

• Do not fill a fuel container when it is

inside your vehicle (including the cargo area). Keep the fuel pump nozzle in contact with the fuel container when filling it. • Do not use a device that holds the fuel

pump nozzle lever in the fill position. Adding Fuel From a Portable Fuel Container

WARNINGS

Do not insert the nozzle of a fuel container or an aftermarket funnel into the fuel system filler neck. This may damage the fuel system filler neck or its seal and cause fuel to run onto the ground.

Do not use any fuel other than those recommended because they could lead to engine damage that may not be covered by the vehicle Warranty. Note: Use of any fuel other than those recommended can impair the emission control system and cause a loss of vehicle performance. Do not use: • Diesel fuel. • •

Fuels containing kerosene or paraffin. Fuels containing more than 85% ethanol or E100 fuel. Fuels containing methanol. Fuels containing metallic-based additives, including manganese-based compounds. Fuels containing the octane booster additive, methylcyclopentadienyl manganese tricarbonyl (MMT). Leaded fuel (using leaded fuel is prohibited by law).

• •

•

•

The use of fuels with metallic compounds such as methylcyclopentadienyl manganese tricarbonyl (commonly known as MMT), which is a manganese-based fuel additive, will impair engine performance and affect the emission control system. Do not be concerned if the engine sometimes knocks lightly. However, if it knocks heavily under most driving conditions while you are using fuel with the recommended octane rating, contact an authorized dealer to prevent any engine damage. FUEL FILLER FUNNEL LOCATION The fuel filler funnel is located in the spare wheel storage tray.

173

Explorer (TUB), enUSA, First Printing

Fuel and Refueling

WARNINGS

Do not try to pry open or push open the capless fuel system with foreign objects. This could damage the fuel system and its seal and cause injury to you or others.

Do not dispose of fuel in the household refuse or the public sewage system. Use an authorized

waste disposal facility.

When refueling the vehicle fuel tank from a fuel container, use the plastic funnel included with your vehicle. See Fuel Filler Funnel Location (page 173). Note: Do not use aftermarket funnels as they will not work with the capless fuel system and can damage it. When refueling the vehicle fuel tank from a fuel container, do the following: 1. Fully open the fuel tank filler door until

it engages and remove the fuel tank filler cap.

Note: Capless fuel systems do not have a fuel tank filler cap. 2. Fully insert the plastic funnel into the

fuel tank filler pipe opening.

3. Add fuel to your vehicle from the fuel

container.

4. Remove the plastic funnel from the

fuel tank filler pipe opening.

5. Replace the fuel tank filler cap and

close the fuel tank filler door.

6. Clean the plastic funnel and place it

back in your vehicle or properly dispose of it.

Note: Extra funnels can be purchased from an authorized dealer if you choose to dispose of the funnel. REFUELING

WARNINGS

Fuel vapor burns violently and a fuel fire can cause severe injuries. Read and follow all the instructions on the pump island. When refueling always shut the engine off and never allow sparks or open flames near the fuel tank filler

valve. Never smoke or use a cell phone while refueling. Fuel vapor is extremely hazardous under certain conditions. Avoid inhaling excess fumes.

Stay outside your vehicle and do not leave the fuel pump unattended when refueling your vehicle. This is

against the law in some places.

Keep children away from the fuel pump; never let children pump fuel. Wait at least 10 seconds before removing the fuel pump nozzle to allow any residual fuel to drain into

the fuel tank.

Stop refueling after the fuel pump nozzle automatically shuts off for the second time. Failure to follow this

will fill the expansion space in the fuel tank and could lead to fuel overflowing.

174

Explorer (TUB), enUSA, First Printing

E157452Fuel and Refueling

WARNINGS

Do not remove the fuel pump nozzle from its fully inserted position when refueling.

Use the following guidelines to avoid electrostatic charge build-up, which can produce a spark, when filling an ungrounded fuel container: • Place approved fuel container on the

ground.

3.

Insert the fuel pump nozzle up to the first notch on the nozzle. Hold handle higher during insertion for easier access. Leave the fuel pump nozzle fully inserted until you are done pumping.

4. Remove the fuel filler nozzle and fully

close the fuel tank filler door.

Note: A fuel spillage concern may occur if overfilling the fuel tank. Do not overfill the tank. The fill pipe is equipped with a drain hole. Excess fuel due to overfill may drain through the drain hole and drip onto the ground. If the fuel fill inlet was not properly closed, a service engine warning lamp may appear on the instrument cluster. At the next opportunity, do the following:

•

• Do not fill a fuel container while it is in the vehicle (including the cargo area). Keep the fuel pump nozzle in contact with the fuel container while filling. • Do not use a device that would hold

the fuel pump handle in the fill position. Easy Fuel™ Capless Fuel System

WARNING

The fuel system may be under pressure. If you hear a hissing sound near the fuel filler door, do not refuel until the sound stops. Otherwise, fuel may spray out, which could cause serious personal injury.

When fueling your vehicle: 1. When your vehicle has stopped, shift into park (P) and switch the ignition off.

2. Fully open the fuel tank filler door until

it engages.

175

Explorer (TUB), enUSA, First Printing

E156032E154765Fuel and Refueling

Filling the Tank For consistent results when filling the fuel tank: •

Turn the ignition off before fueling; an inaccurate reading results if the engine is left running.

• Use the same fill rate

(low-medium-high) each time the tank is filled.

• Allow no more than two automatic

click-offs when filling.

Results are most accurate when the filling method is consistent. Calculating Fuel Economy Do not measure fuel economy during the first 1000 miles (1600 kilometers) of driving (this is your engine’s break-in period); a more accurate measurement is obtained after 2000 miles - 3000 miles (3200 kilometers - 4800 kilometers). Also, fuel expense, frequency of fill ups or fuel gauge readings are not accurate ways to measure fuel economy. 1. Fill the fuel tank completely and record

the initial odometer reading.

2. Each time you fill the tank, record the

amount of fuel added.

3. After at least 3 to 5 tank fill ups, fill the

fuel tank and record the current odometer reading.

4. Subtract your initial odometer reading

from the current odometer reading. 5. Calculate fuel economy by dividing miles traveled by gallons used (For Metric: Multiply liters used by 100, then divide by kilometers traveled).

1. Stop your vehicle as soon as safely

possible and shift the transmission into park (P).

2. Switch the ignition off. 3. Open the fuel filler door and remove

any visible debris from the fuel fill opening. Insert either the fuel fill nozzle or the fuel fill funnel provided with the vehicle several times to allow the inlet to close properly. This will dislodge any debris preventing the inlet from sealing.

4.

If this action corrects the problem, the message may not reset immediately. It may take several driving cycles for the message to turn off. A driving cycle consists of an engine start-up (after 4 or more hours with the engine off) followed by city or highway driving. Continuing to drive with the message on may cause the service engine soon lamp to turn on as well. FUEL CONSUMPTION Empty reserve is the amount of fuel remaining in the tank after the fuel gauge indicates empty. The amount of usable fuel in the empty reserve varies and should not be relied upon to increase driving range. The usable capacity of the fuel tank is • the amount of fuel that can be added into the tank after the gauge indicates empty The advertised capacity is the total fuel tank size. See Capacities and Specifications (page 334). It is the combined usable capacity plus the empty reserve.

•

• Due to the empty reserve, you may not be able to refuel the full amount of the advertised capacity of the fuel tank even when the fuel gauge reads empty.

176

Explorer (TUB), enUSA, First Printing

Fuel and Refueling

EMISSION CONTROL SYSTEM

WARNINGS

Do not park, idle, or drive your vehicle in dry grass or other dry ground cover. The emission system heats up the

engine compartment and exhaust system, which can start a fire.

Exhaust leaks may result in entry of harmful and potentially lethal fumes into the passenger compartment. If

you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately. Do not drive if you smell exhaust fumes.

Your vehicle is equipped with various emission control components and a catalytic converter that will enable your vehicle to comply with applicable exhaust emission standards. To make sure that the catalytic converter and other emission control components continue to work properly: • Use only the specified fuel listed. • Avoid running out of fuel. • Do not turn off the ignition while your

vehicle is moving, especially at high speeds.

• Have the items listed in scheduled

maintenance information performed according to the specified schedule. The scheduled maintenance items listed in scheduled maintenance information are essential to the life and performance of your vehicle and to its emissions system. If you use parts other than Ford, Motorcraft or Ford-authorized parts for maintenance replacements, or for service of components affecting emission control, such non-Ford parts should be the equivalent to genuine Ford Motor Company parts in performance and durability.

Keep a record for at least 1 month and record the type of driving (city or highway). This provides an accurate estimate of the vehicle’s fuel economy under current driving conditions. Additionally, keeping records during summer and winter show how temperature impacts fuel economy. In general, lower temperatures mean lower fuel economy. Conditions • Heavily loading a vehicle or towing a

trailer may reduce fuel economy at any speed.

• Carrying unnecessary weight may

reduce fuel economy (approximately 1 mpg [0.4 km/L] is lost for every 400
pounds [180 kilograms] of weight carried).

• Adding certain accessories to your

vehicle (for example bug deflectors, rollbars/light bars, running boards, ski racks) may reduce fuel economy.

• Using fuel blended with alcohol may

lower fuel economy. Fuel economy may decrease with lower temperatures during the first 8–10
miles (12–16 kilometers) of driving.

•