2015 Ford Escape Owners Manual

sure they work properly and are not damaged. Inspect the vehicle and child seat safety belts to make sure there are no nicks, tears or cuts. Replace if necessary. All vehicle safety belt assemblies, including retractors, buckles, front safety belt buckle assemblies, buckle support assemblies (slide bar-if equipped), shoulder belt height adjusters (if equipped), shoulder belt guide on seat back (if equipped), child safety seat LATCH and tether anchors, and attaching hardware, should be inspected after a crash. Read the child restraint manufacturer's instructions for additional inspection and maintenance information specific to the child restraint. Ford Motor Company recommends that all safety belt assemblies in use in vehicles involved in a crash be replaced. However, if the crash was minor and an authorized dealer finds that the belts do not show damage and continue to operate properly, they do not need to be replaced. Safety belt assemblies not in use during a crash should also be inspected and replaced if either damage or improper operation is noted. Properly care for safety belts. See Vehicle Care (page 236).

Deactivating and Activating the Belt-Minder Feature

WARNING

While the system allows you to deactivate it, this system is designed to improve your chances of being safely belted and surviving an accident. We recommend you leave the system activated for yourself and others who may use your vehicle.

Note: The driver and front passenger warnings switch on and off independently. When you perform this procedure for one seating position, do not buckle the other position as this will terminate the process. Read Steps 1 - 4 thoroughly before proceeding with the programming procedure. Before following the procedure, make sure that: • • • •

The parking brake is set. The transmission is in park (P). The ignition is off. The driver and front passenger safety belts are unbuckled.

1. Switch the ignition on. Do not start the

engine.

2. Wait until the safety belt warning light

turns off (about one minute). After Step 2, wait an additional five seconds before proceeding with Step 3. Once you start Step 3, you must complete the procedure within 60 seconds.

3. For the seating position you are

switching off, buckle then unbuckle the safety belt three times at a moderate speed, ending in the unbuckled state. After Step 3, the safety belt warning light turns on.

38

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Personal Safety System™

How Does the Personal Safety System Work? The Personal Safety System can adapt the deployment strategy of the safety devices according to crash severity and occupant conditions. A collection of crash and occupant sensors provides information to the restraints control module. During a crash, the restraints control module may deploy the safety belt pretensioners, one or both stages of the dual-stage airbags based on crash severity and occupant conditions.

The Personal Safety System provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriate safety devices to help better protect a range of occupants in a variety of frontal crash situations. The Vehicle Personal Safety System consists of: • Driver and passenger dual-stage airbag

supplemental restraints. Front seat outboard safety belts with pretensioners, energy management retractors and safety belt usage sensors.

• Driver seat position sensor. • • Passenger airbag off and on indicator

Front passenger sensing system.

lamp. Front crash severity sensors.

• • Restraints control module with impact

and safing sensors.

• Restraint system warning light and

backup tone. The electrical wiring for the airbags, crash sensors, safety belt pretensioners, front safety belt usage sensors, driver seat position sensor, front passenger sensing system and indicator lights.

•

•

39

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Supplementary Restraints System

The airbags are a supplemental restraint system and are designed to work with the safety belts to help protect the driver and right front passenger from certain upper body injuries. Airbags do not inflate slowly; there is a risk of injury from a deploying airbag. Note: You will hear a loud bang and see a cloud of harmless powdery residue if an airbag deploys. This is normal. The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (for example, baking soda) that result from the combustion process that inflates the airbag. Small amounts of sodium hydroxide may be present which may irritate the skin and eyes, but none of the residue is toxic. While the system is designed to help reduce serious injuries, contact with a deploying airbag may also cause abrasions or swelling. Temporary hearing loss is also a possibility as a result of the noise associated with a deploying airbag. Because airbags must inflate rapidly and with considerable force, there is the risk of death or serious injuries such as fractures, facial and eye injuries or internal injuries, particularly to occupants who are not properly restrained or are otherwise out of position at the time of airbag deployment. Thus, it is extremely important that occupants be properly restrained as far away from the airbag module as possible while maintaining vehicle control. Routine maintenance of the airbags is not required.

PRINCIPLE OF OPERATION

WARNINGS

Airbags do not inflate slowly or gently, and the risk of injury from a deploying airbag is the greatest close

to the trim covering the airbag module.

All occupants of your vehicle, including the driver, should always properly wear their safety belts, even

when an airbag supplemental restraint system is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

Always transport children 12 years old and under in the back seat and always properly use appropriate

child restraints. Failure to follow this could seriously increase the risk of injury or death. Never place your arm over the airbag module as a deploying airbag can result in serious arm fractures or

other injuries.

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back. Do not attempt to service, repair, or modify the airbag supplemental restraint systems or its fuses as you could be seriously injured or killed. Contact your authorized dealer as soon as possible. Several airbag system components get hot after inflation. Do not touch them after inflation as this may result

in serious injury.

If the airbag has deployed, the airbag will not function again and must be replaced immediately. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

40

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Supplementary Restraints System

Proper Driver and Front Passenger Seating Adjustment WARNING

National Highway Traffic Safety Administration (NHTSA) recommends a minimum distance

of at least 10 inches (25 centimeters) between an occupant’s chest and the driver airbag module.

To properly position yourself away from the airbag: • Move your seat to the rear as far as you

can while still reaching the pedals comfortably.

• Recline the seat slightly (one or two degrees) from the upright position. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seat back, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. Children and Airbags WARNING

Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

DRIVER AND PASSENGER AIRBAGS

WARNINGS

Never place your arm or any objects over an airbag module. Placing your arm over a deploying airbag can result in serious arm fractures or other injuries. Objects placed on or over the airbag inflation area may cause those objects to be propelled by the airbag into your face and torso causing serious injury. Airbags can kill or injure a child in a child seat. Never place a rear-facing child seat in front of an active airbag. If you must use a forward-facing child seat in the front seat, move the seat upon which the child seat is installed all the way back.

The driver and front passenger airbags will deploy during significant frontal and near frontal crashes. The driver and passenger front airbag system consists of: • Driver and passenger airbag modules. •

Front passenger sensing system.

· Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 47).

41

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E151127Supplementary Restraints System

The indicator lamp is located in the center stack of the instrument panel. The front passenger sensing system is designed to disable (will not inflate) the front passenger frontal airbag under certain conditions: •

The front passenger seat is unoccupied. The system determines an infant is present in a child restraint.

•

• A passenger takes their weight off the

seat for a period of time. If there is a problem with the airbag system or the passenger sensing system.

•

Even with this technology, parents are strongly encouraged to always properly restrain children in the rear seat.

Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions may increase the risk of injury in a crash. FRONT PASSENGER SENSING SYSTEM

WARNINGS

Even with Advanced Restraints Systems, children 12 and under should be properly restrained in a

rear seating position. Failure to follow this could seriously increase the risk of injury or death.

Sitting improperly out of position or with the seatback reclined too far can take off weight from the seat

cushion and affect the decision of the front passenger sensing system, resulting in serious injury or death in a crash.

Always sit upright against your seat back, with your feet on the floor. Any alteration or modification to the front passenger seat may affect the performance of the front passenger

sensing system which could seriously increase the risk of injury or death.

42

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142846E145987Supplementary Restraints System

• When the front passenger sensing

• Restart the vehicle and have the person

•

remain in this position for about two minutes. This will allow the system to detect that person and enable the passenger’s frontal airbag. If the passenger airbag status indicator lamp remains lit even after this, the person should be advised to ride in the rear seat.

Note: When the passenger airbag status indicator lamp is illuminated, the passenger side airbag (seat mounted) may be disabled to avoid the risk of airbag deployment injuries. After all occupants have adjusted their seats and put on safety belts, it is very important that they continue to sit properly. A properly seated occupant sits upright, leaning against the seatback, and centered on the seat cushion, with their feet comfortably extended on the floor. Sitting improperly can increase the chance of injury in a crash event. For example, if an occupant slouches, lies down, turns sideways, sits forward, leans forward or sideways, or puts one or both feet up, the chance of injury during a crash is greatly increased. If you think that the status of the passenger airbag off indicator lamp is incorrect, check for the following: • Objects lodged underneath the seat. • Objects between the seat cushion and

the center console.

• Objects hanging off the seatback. • Objects stowed in the seatback map

pocket.

• Objects placed on the occupant's lap. • Cargo interference with the seat. • Other passengers pushing or pulling on

the seat.

• Rear passenger feet and knees resting

or pushing on the seat.

system disables (will not inflate) the front passenger frontal airbag, the passenger airbag status indicator will illuminate and stay lit to remind you that the front passenger frontal airbag is disabled. If the passenger airbag status indicator lamp indicates the passenger airbag is enabled, after the child restraint has been installed, turn the vehicle off, remove the child restraint from the vehicle and reinstall the restraint following the child restraint manufacturer’s instructions. If the passenger airbag status indicator lamp continues to indicate the passenger airbag is enabled, the child should be properly restrained in a rear seating position.

•

•

The front passenger sensing system works with sensors that are part of the front passenger seat and safety belt. The sensors are designed to detect the presence of a properly–seated occupant and determine if the front passenger frontal airbag should be enabled. • When the front passenger sensing

system enables the front passenger frontal airbag (may inflate), the passenger airbag status indicator will not illuminate.

If a person of adult size is sitting in the front passenger seat, but the passenger airbag is disabled, it is possible that the person is not sitting properly in the seat. If this happens: •

Turn the vehicle off and ask the person to place the seatback in the full upright position.

• Have the person sit upright in the seat, centered on the seat cushion, with the person's legs comfortably extended.

43

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Supplementary Restraints System

SIDE AIRBAGS

WARNINGS

Do not place objects or mount equipment on or near the airbag cover, on the side of the seatbacks (of the front seats), or in front seat areas that may come into contact with a deploying airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not use accessory seat covers. The use of accessory seat covers may prevent the deployment of the side airbags and increase the risk of injury in an accident.

Do not lean your head on the door. The side airbag could injure you as it deploys from the side of the

seatback.

Do not attempt to service, repair, or modify the airbag, its fuses or the seat cover on a seat containing an

airbag as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

If the side airbag has deployed, the airbag will not function again. The side airbag system (including the

seat) must be inspected and serviced by an authorized dealer. If the airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The side airbags are located on the outboard side of the seatbacks of the front seats. In certain sideways crashes, the airbag on the side affected by the crash will be inflated. The airbag was designed to inflate between the door panel and occupant to further enhance the protection provided occupants in side impact crashes.

The conditions listed above may cause the weight of a properly seated occupant to be incorrectly interpreted by the passenger sensing system. The person in the front passenger seat may appear heavier or lighter due to the conditions described in the list above.

Make sure the front passenger sensing system is operating properly. See Crash Sensors

and Airbag Indicator (page 47). If the airbag readiness lamp is lit, do the following: Check for objects that are lodged underneath the front passenger seat, or cargo interfering with the seat. If there are lodged objects, or cargo is interfering with the seat, take the following steps to remove the obstruction: • Pull the vehicle over. • Turn the vehicle off. • Driver or adult passengers should

check for any objects lodged underneath the front passenger seat or cargo interfering with the seat.

• Remove the obstruction(s) (if found). • Restart the vehicle. • Wait at least two minutes and verify that the airbag readiness lamp is no longer illuminated. If the airbag readiness lamp remains illuminated, this may or may not be a problem due to the front passenger sensing system.

•

Do not attempt to repair or service the system; take your vehicle immediately to an authorized dealer. If it is necessary to modify an advanced front airbag system to accommodate a person with disabilities, contact your authorized dealer.

44

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Supplementary Restraints System

DRIVER KNEE AIRBAG A driver's knee airbag is located under the instrument panel. During a crash, the restraints control module may activate the driver's knee airbag based on crash severity and occupant conditions. Under certain crash and occupant conditions, the driver’s knee airbag may deploy but the driver’s front airbag may not activate. As with front and side airbags, it is important to be properly seated and restrained to reduce the risk of death or serious injury.

Make sure the knee airbag is operating properly. See Crash Sensors and Airbag Indicator

(page 47).

SAFETY CANOPY™ WARNINGS

Do not place objects or mount equipment on or near the headliner at the siderail that may come into contact with a deploying curtain airbag. Failure to follow these instructions may increase the risk of personal injury in the event of a crash.

Do not lean your head on the door. The curtain airbag could injure you as it deploys from the headliner. Do not attempt to service, repair, or modify the curtain airbags, its fuses, the A, B, or C pillar trim, or the

headliner on a vehicle containing curtain airbags as you could be seriously injured or killed. Contact your authorized dealer as soon as possible.

The system consists of the following: • A label or embossed side panel

indicating that side airbags are fitted to your vehicle. Side airbags located inside the driver and front passenger seatbacks. Front passenger sensing system.

•

•

·Crash sensors and monitoring system with readiness indicator. See Crash Sensors and Airbag

Indicator (page 47). Note: The passenger sensing system will deactivate the passenger seat-mounted side airbag if it detects an empty passenger seat. The design and development of the side airbag system included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags.

45

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E152533Supplementary Restraints System

WARNINGS

All occupants of your vehicle including the driver should always wear their safety belts even when an airbag supplemental restraint system and curtain airbag is provided. Failure to properly wear your safety belt could seriously increase the risk of injury or death.

To reduce risk of injury, do not obstruct or place objects in the deployment path of the curtain

airbag.

If the curtain airbags have deployed, the curtain airbags will not function again. The curtain airbags (including

the A, B and C pillar trim and headliner) must be inspected and serviced by an authorized dealer. If the curtain airbag is not replaced, the unrepaired area will increase the risk of injury in a crash.

The Safety Canopy will deploy during significant side crashes or when a certain likelihood of a rollover event is detected by the rollover sensor. The Safety Canopy is mounted to the roof side-rail sheet metal, behind the headliner, above each row of seats. In certain sideways crashes or rollover events, the Safety Canopy will be activated, regardless of which seats are occupied. The Safety Canopy is designed to inflate between the side window area and occupants to further enhance protection provided in side impact crashes and rollover events.

46

Escape (TM2) Canada/United States of America, enUSA, Second Printing

The system consists of the following: •

Safety canopy curtain airbags located above the trim panels over the front and rear side windows identified by a label or wording on the headliner or roof-pillar trim.

• A flexible headliner which opens above

the side doors to allow air curtain deployment

· Crash sensors and monitoring system with a readiness indicator. See Crash Sensors and Airbag Indicator (page 47). Children 12 years old and under should always be properly restrained in the rear seats. The Safety Canopy will not interfere with children restrained using a properly installed child or booster seat because it is designed to inflate downward from the headliner above the doors along the side window opening. The design and development of the Safety Canopy included recommended testing procedures that were developed by a group of automotive safety experts known as the Side Airbag Technical Working Group. These recommended testing procedures help reduce the risk of injuries related to the deployment of side airbags (including the Safety Canopy).

E75004Supplementary Restraints System

CRASH SENSORS AND AIRBAG INDICATOR WARNING

Modifying or adding equipment to the front end of the vehicle (including frame, bumper, front end body

structure and tow hooks) may affect the performance of the airbag system, increasing the risk of injury. Do not modify the front end of the vehicle.

Your vehicle has a collection of crash and occupant sensors which provide information to the restraints control module. The restraints control module deploys (activates) the front safety belt pretensioners, driver airbag, passenger airbag, knee airbag(s), seat mounted side airbags and Safety Canopy airbags. Based on the type of crash (frontal impact or side impact), the restraints control module will deploy the appropriate safety devices. The restraints control module also monitors the readiness of the above safety devices plus the crash and occupant sensors. The readiness of the safety system is indicated by a warning indicator light in the instrument cluster or by a backup tone if the warning light is not working. Routine maintenance of the airbag is not required. A difficulty with the system is indicated by one or more of the following:

The readiness light will not illuminate immediately after the ignition is turned on.

•

The readiness light will either flash or stay lit.

• A series of five beeps will be heard. The

tone pattern will repeat periodically until the problem, the light or both are repaired.

Escape (TM2) Canada/United States of America, enUSA, Second Printing

If any of these things happen, even intermittently, have the supplemental restraint system serviced at an authorized dealer immediately. Unless serviced, the system may not function properly in the event of a crash. The safety belt pretensioners and the front airbag supplemental restraint system are designed to activate when the vehicle sustains frontal deceleration sufficient to cause the restraints control module to deploy a safety device. The fact that the safety belt pretensioners or front airbags did not activate for both front seat occupants in a crash does not mean that something is wrong with the system. Rather, it means the restraints control module determined the accident conditions (crash severity, belt usage) were not appropriate to activate these safety devices. •

The design of the front airbags is to activate only in frontal and near-frontal crashes (not rollovers, side impacts or rear impacts) unless the crash causes sufficient frontal deceleration. The safety belt pretensioners are designed to activate in frontal, near-frontal and side crashes. The knee airbag(s) may deploy based on crash severity and occupant conditions. The design of the side airbags is to inflate in certain side crashes. The design of the Safety Canopy is to inflate in certain side impact crashes and when a certain likelihood of rollover is detected by the rollover sensor. Side airbags and Safety Canopy airbags may activate in other types of crashes if the vehicle experiences sufficient sideways motion or deformation.

•

•

•

47

Supplementary Restraints System

AIRBAG DISPOSAL Contact your authorized dealer as soon as possible. Airbags must be disposed of by qualified personnel.

48

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Keys and Remote Controls

Structures around the vehicle.

• • Other vehicles parked next to your

vehicle.

The radio frequency used by your remote control can also be used by other radio transmitters, for example amateur radios, medical equipment, wireless headphones, wireless remote controls, cell phones, battery chargers and alarm systems. If the frequencies are jammed, you will not be able to use your remote control. You can lock and unlock the doors with the key. Note: Make sure to lock your vehicle before leaving it unattended. Note: If you are in range, the remote control will operate if you press any button unintentionally. Intelligent Access (If Equipped) The system uses a radio frequency signal to communicate with your vehicle and authorize your vehicle to unlock when one of the following conditions are met: •

You activate the front exterior door handle switch. You press the luggage compartment button. • You press a button on the transmitter. If excessive radio frequency interference is present in the area or if the transmitter battery is low, you may need to mechanically unlock your door. You can use the mechanical key blade in your intelligent access key to open the driver door in this situation. See Remote Control (page 50).

•

PRINCIPLE OF OPERATION The remote control allows you to: • Remotely lock or unlock the vehicle

doors.

• Unlock the doors without actively using

a key or remote control (intelligent access only).

• Remotely open the power liftgate (if

equipped).

• Remotely start or stop the engine and

user pre-set features (if equipped).

• Arm and disarm the anti-theft system. • Activate the panic alarm. GENERAL INFORMATION ON RADIO FREQUENCIES This device complies with Part 15 of the FCC Rules and with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Note: Changes or modifications not expressively approved by the party responsible for compliance could void the user's authority to operate the equipment. The term IC before the radio certification number only signifies that Industry Canada technical specifications were met. The typical operating range for your transmitter is approximately 33 ft (10 m). Vehicles with the remote start feature will have a greater range. One of the following could cause a decrease in operating range: • Weather conditions. • Nearby radio towers.

49

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Keys and Remote Controls

REMOTE CONTROL Integrated Keyhead Transmitters (If Equipped)

Your intelligent access keys operate the power locks and the remote start system. The key must be in your vehicle to activate the push-button start system.

Use the key blade to start your vehicle and unlock or lock the driver door from outside your vehicle. The transmitter portion functions as the remote control.

The intelligent access key also contains a removable mechanical key blade that you can use to unlock the driver door. Slide the release on the back of the transmitter to release the key blade, then pull the blade out.

Note: Your vehicle’s keys came with a security label that provides important vehicle key cut information. Keep the label in a safe place for future reference. Intelligent Access Key (If Equipped) Note: A three-button remote control will operate similarly.

Note: Your vehicle’s back-up keys came with a security tag that provides important vehicle key cut information. Keep the tag in a safe place for future reference. Replacing the Battery Note: Refer to local regulations when disposing of transmitter batteries. Note: Do not wipe off any grease on the battery terminals or on the back surface of the circuit board.

50

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E142585E138615E138616E142431E138618Keys and Remote Controls

Note: Replacing the battery will not delete the transmitter from the vehicle. The transmitter should operate normally. The remote control uses one coin-type three-volt lithium battery CR2032 or equivalent. Integrated Keyhead Transmitter

2. Twist a thin coin under the tab hidden behind the backup key head to remove the battery cover. Do not use the backup key to remove the cover or you could damage the intelligent access key.

3. Remove the old battery. 4.

Insert a new battery with the + facing downward. Press the battery down to make sure it is fully in the housing.

5. Snap the battery cover back onto the transmitter and install the backup key.

Car Finder

Press the button twice within three seconds. The horn will sound and the turn signals will flash. We recommend you use this method to locate your vehicle, rather than using the panic alarm.

1. Twist a thin coin in the slot of the

transmitter near the key ring to remove the battery cover.

2. Remove the old battery.

3.

Insert the new battery. Refer to the instructions inside the transmitter for the correct orientation of the battery. Press the battery down to make sure it is fully in the housing.

4. Snap the battery cover back onto the

transmitter.

Intelligent Access Transmitter 1. Remove the backup key from the

transmitter.

51

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138619E138620E142432E138622E138623Keys and Remote Controls

• • • •

the hood is open the transmission is not in P the vehicle battery voltage is too low the service engine soon indicator was on the last time your vehicle was driven.

Remote Starting the Vehicle Note: You must press each button within three seconds of each other. Your vehicle will not remote start and the horn will not sound if you do not follow this sequence.

The label on your transmitter details the starting procedure. To remote start your vehicle: 1. Press the lock button to lock all the

doors.

2. Press the remote start button twice. The exterior lamps will flash twice.

The horn will sound if the system fails to start, unless quiet start is on. Quiet start will run the blower fan at a slower speed to reduce noise. You can switch it on or off in the information display. See General Information (page 93). Note: If you remote start your vehicle with an integrated keyhead transmitter, you must switch the ignition on before driving your vehicle. If you remote start your vehicle with an intelligent access transmitter, you must press the START/STOP button on the instrument panel once while applying the brake pedal before driving your vehicle.

Note: If locking was not successful or if any door or the liftgate is open, or if the hood is open on vehicles with a perimeter alarm or remote start, the horn will sound twice and the lamps will not flash. Sounding a Panic Alarm Note: The panic alarm will only operate when the ignition is off.

Press the button to activate the alarm. Press the button again or turn the ignition on to deactivate.

Remote Start (If Equipped) WARNING

To avoid exhaust fumes, do not use remote start if your vehicle is parked indoors or areas that are not well

ventilated.

Note: Do not use remote start if your vehicle is low on fuel.

The remote start button is on the transmitter.

This feature allows you to start your vehicle from outside the vehicle. The transmitter has an extended operating range. Vehicles with automatic climate control can be configured to operate when the vehicle is remote started. See Automatic Climate Control (page 107). Many states and provinces have restrictions for the use of remote start. Check your local and state or provincial laws for specific requirements regarding remote start systems. The remote start system will not work if: • • •

the ignition is on the alarm system is triggered you disable the feature

52

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138624E138625E138626Keys and Remote Controls

The power windows will be inhibited during the remote start and the radio will not turn on automatically. The parking lamps will remain on and the vehicle will run for 5, 10, or 15 minutes, depending on the setting. Extending the Vehicle Run Time Repeat Steps 1 and 2 with the vehicle still running to extend the run time for another remote start duration. If the duration is set to last 10 minutes, the duration will extend by another 10 minutes. For example, if the vehicle had been running from the first remote start for five minutes, the vehicle will continue to run now for a total of 20
minutes. You can only extend the remote start once. Some late build vehicles may be able to restart up to 30 minutes. Wait at least five seconds before remote starting after a vehicle shutdown. Turning the Vehicle Off After Remote Starting

Press the button once. The parking lamps will turn off. You may have to be closer to the vehicle than when starting due to ground reflection and the added noise of the running vehicle. You can disable or enable the remote start system through the information display. See General Information (page 93).

REPLACING A LOST KEY OR REMOTE CONTROL Replacement keys or remote controls can be purchased from an authorized dealer. Authorized dealers can program remote controls for your vehicle. See Passive Anti-Theft System (page 69). To re-program the passive anti-theft system see an authorized dealer.

53

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138625MyKey™

• Driver assist features, if equipped on

your vehicle, are forced on: parking aid, blind spot information system (BLIS) with cross traffic alert, lane departure warning and forward collision warning system. Satellite radio adult content restrictions.

•

Configurable Settings With an admin key, you can configure certain MyKey settings when you first create a MyKey and before you recycle the key or restart the vehicle. You can also change the settings afterward with an admin key: • Vehicle speed limits can be set.

Warnings will be shown in the display followed by an audible tone when your vehicle reaches the set speed. You cannot override the set speed by fully depressing the accelerator pedal.

• Vehicle speed minders. Once you select a speed, it will be shown in the display followed by a tone when the set vehicle speed is exceeded.

• Audio system maximum volume of

45%. A message will be shown in the display when you attempt to exceed the limited volume. Also, the speed sensitive compensated volume (automatic volume control) feature will be disabled.

• Always on setting. When this is

selected you will not be able to disable AdvanceTrac, 911 Assist or the do not disturb feature (if your vehicle is equipped with these features).

CREATING A MYKEY Use the information display to create a MyKey:

•

PRINCIPLE OF OPERATION MyKey allows you to program keys with restricted driving modes to promote good driving habits. All but one of the keys programmed to the vehicle can be activated with these restricted modes. Any keys that have not been programmed are referred to as administrator keys or admin keys. These can be used to: • Create a MyKey. • Program configurable MyKey settings. • Clear all MyKey features. When you have created a MyKey, you can access the following information using the information display: • How many admin keys and MyKeys are

programmed to your vehicle. The total distance your vehicle has traveled using any MyKey.

Note: All MyKeys are programmed to the same settings. You cannot program them individually. Note: For vehicles with keyless start, when both a MyKey transmitter and an admin transmitter are present, the admin transmitter will be recognized by the vehicle to start the engine. Non-configurable Settings The following settings cannot be changed by an admin key user: •

Belt-minder. You cannot disable this feature. The audio system will mute when the safety belts are not fastened. Early low fuel warning. The low-fuel warning activates earlier, giving the MyKey user more time to refuel.

•

54

Escape (TM2) Canada/United States of America, enUSA, Second Printing

MyKey™

1. Insert the key you want to program into the ignition. If your vehicle is equipped with a push-button start, hold the intelligent access key next to the steering column. Details on the correct fob placement and position is in another chapter. See Starting and Stopping the Engine (page 128). 2. Switch the ignition on. 3. Access the main menu on the information display controls, and select Settings and then MyKey by pressing OK or the > button. 4. Press OK or the > button to select Create MyKey. 5. When prompted, hold the OK button until you see a message informing you to label this key as a MyKey. The key will be restricted at your vehicle's next start. MyKey is successfully created. Make sure you label it so you can distinguish it from the admin keys. You can also program configurable settings for the key(s). Refer to Programming/Changing Configurable Settings.

Programming/Changing Configurable Settings Use the information display to access your configurable MyKey settings: 1. Switch the ignition on using an admin

key or fob.

2. Access the main menu on the

information display controls, and select Settings, then MyKey by pressing OK or the > button.

3. Use the arrow buttons to get to a

configurable feature.

4. Press OK or > to make a selection. Note: You can clear or change your MyKey settings at any time during the same key cycle as you created the MyKey. Once you have switched the engine off, however, you will need an admin key to change or clear your MyKey settings. CLEARING ALL MYKEYS You can clear or change your MyKey settings using the information display control on the steering wheel. See Information Displays (page 93). Switch the ignition on using an admin key or fob.

To clear all MyKeys of all MyKey settings, press the left arrow button to access the main menu and scroll to:

Message

Action and Description

Settings MyKey Clear MyKey

Press the OK button. Press the OK button. Press and hold the OK button until the following message displays.

All MyKeys Cleared Note: When you clear your MyKeys, you remove all restrictions and return all MyKeys to their original admin key status.

55

Escape (TM2) Canada/United States of America, enUSA, Second Printing

MyKey™

CHECKING MYKEY SYSTEM STATUS

You can find information on programmed MyKey(s) using the information display control on the steering wheel. See Information Displays (page 93).

To find information on programmed MyKey(s), press the left arrow button to access the main menu and scroll to:

Message

Description

Settings MyKey Select one of the following: MyKey Dist.

Press the OK button. Press the OK button.

Tracks the distance when drivers use a MyKey. The only way to delete the accumulated distance is by using an admin key to clear your MyKeys. If the distance does not accumulate as expected, then the intended user is not using the MyKey, or an admin key user recently cleared and then recreated a MyKey. Indicates the number of MyKeys programmed to your vehicle. Use this feature to detect how many MyKeys you have for your vehicle and determine when a MyKey has been deleted. Indicates how many admin keys are programmed to your vehicle. Use this feature to determine how many unrestricted keys you have for your vehicle, and detect if an additional MyKey has been programmed.

{0} MyKeys

{0} Admin Keys

56

Escape (TM2) Canada/United States of America, enUSA, Second Printing

MyKey™

USING MYKEY WITH REMOTE START SYSTEMS MyKey is not compatible with non MYKEY TROUBLESHOOTING

Ford-approved, aftermarket remote start systems. If you choose to install a remote start system, see an authorized dealer for a Ford-approved remote start system.

Condition I cannot create a MyKey.

Potential Causes

•

•

The key or transmitter used to start the vehicle does not have admin privileges. The key or transmitter used to start the vehicle is the only admin key (there always has to be at least one admin key).

• Vehicles with keyless start: The keyless

start transmitter is not placed in the backup position. See Starting a Gasoline Engine (page 129). SecuriLock passive anti-theft system is disabled or in unlimited mode.

•

I cannot program the configurable settings.

I cannot clear the MyKeys.

•

The key or transmitter used to start your vehicle does not have admin privileges. • No MyKeys are created. See Creating a

MyKey (page 54).

•

The key or transmitter used to start your vehicle does not have admin privileges. • No MyKeys are created. See Creating a

MyKey (page 54).

I lost the only admin key.

Purchase a new key from an authorized dealer.

57

Escape (TM2) Canada/United States of America, enUSA, Second Printing

MyKey™

Condition

Potential Causes

I lost a key.

MyKey distances do not accumulate.

No MyKey functions with the keyless entry transmitter.

Program a spare key. See Passive Anti-Theft System (page 69). • The MyKey user is not using the MyKey. • An admin key holder cleared the MyKeys

and created new MyKeys. The key system has been reset.

•

• An admin transmitter is present at vehicle

start.

• No MyKeys are created. See Creating a

MyKey (page 54).

58

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Locks

LOCKING AND UNLOCKING You can use the power door lock control or the remote control to lock and unlock your vehicle. Power Door Locks The power door lock control is on the driver and front passenger door panels.

Unlock Lock

Door Lock Indicator An LED on the instrument panel will light when you lock the doors. It is not a functional control. Remote Control Unlocking the Doors (Two-Stage Unlock)

Press the button to unlock the driver door. Press the button again within

three seconds to unlock all doors. The turn signals will flash.

Press and hold both the lock and unlock buttons on the remote control for four seconds to disable or enable two-stage unlocking. Disabling two-stage unlocking allows all vehicle doors to unlock with one press of the button. The turn signals will flash twice to indicate a change to the unlocking mode. The unlocking mode applies to the remote control, keyless entry keypad and intelligent access. Intelligent access at the driver door will unlock all doors when you disable two-stage unlocking. Locking the Doors

Press the button to lock all the doors. The turn signals will flash. Press the button again within

three seconds to confirm that all the doors are closed. The doors will lock again, the horn will sound and the turn signals will flash if all the doors and the luggage compartment are closed. Note: If locking was not successful or any door or the liftgate is open, or if the hood is open on vehicles with a perimeter alarm or remote start, the horn will sound twice and the lamps will not flash. Liftgate

WARNINGS

Make sure all persons are clear of the liftgate area before using the liftgate control. Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.

59

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138628E138629E138623Locks

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate.

Press twice within three seconds to:

• •

unlatch a manual liftgate open, close or stop the movement of a power liftgate. See Power Liftgate (page 64).

Mechanical Key Turn the top of the key toward the front of your vehicle once to lock all doors. Turn the top of the key toward the rear of your vehicle once to unlock the driver door only. Locking the Doors Individually If the power locks fail to operate, lock the doors individually using the key in the position shown.

Right-Hand Side Turn counterclockwise to lock. Opening a Rear Door from Inside Pull the interior door release handle twice to unlock and open a rear door. The first pull unlocks the door and the second pull will unlatch the door. Activating Intelligent Access (If Equipped) The intelligent access key must be within 3 feet (1 meter) of your vehicle. At the Front Doors Pull a front exterior door handle to unlock and open the door. The unlock sensor is on the back of the handle. Make sure not to touch the lock sensor area on the front of the handle.

Touch the lock sensor area for a few seconds to lock your vehicle. To avoid inadvertently unlocking the door, make sure you only touch the lock sensor and no other area of the door handle. After locking the doors with the lock sensor, there is a brief delay before you can unlock your vehicle. This delay lets you pull the handle to make sure it locked.

60

Left-Hand Side Turn clockwise to lock.

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138630E112203E185863Locks

In order to override the smart unlock feature and intentionally lock the intelligent access key inside your vehicle, you can lock your vehicle after all doors are closed by using the keyless entry keypad, pressing the lock button on another intelligent access key or touching the locking area on the handle with another intelligent access key in your hand. When you open one of the front doors and lock your vehicle using the power door lock control, all doors will lock then unlock if the ignition is on. Autolock (If Equipped) The autolock feature will lock all the doors when: • • •

all doors are closed, the ignition is on, you shift into any gear putting your vehicle in motion, and your vehicle attains a speed greater than 4 mph (7 km/h).

•

Autounlock (If Equipped) The autounlock feature will unlock all the doors when: •

the ignition is on, all the doors are closed, and your vehicle has been in motion at a speed greater than 4 mph (7 km/h); your vehicle comes to a stop and you switch the ignition off or to accessory; and you open the driver door within 10
minutes of the switching the ignition off or to accessory.

•

•

Note: The doors will not autounlock if you electronically lock your vehicle after you switch the ignition off and before you open the driver door.

Note: Keep the door handle surface clean to avoid issues with operation. At the Liftgate Press the exterior liftgate release button on the top of the liftgate pull-cup handle. Smart Unlocks For Integrated Keyhead Transmitter This feature helps to prevent you from locking yourself out of your vehicle if your key is still in the ignition. When you open one of the front doors and lock your vehicle with the power door lock control, all the doors will lock then unlock if your key is still in the ignition. You can still lock your vehicle with the key in the ignition by either: •

using the keyless entry keypad with the driver door closed pressing the lock button on the transmitter even if the doors are not closed.

•

If both front doors are closed, you can lock your vehicle by any method, regardless of whether the key is in the ignition or not. Smart Unlocks For Intelligent Access Keys (If Equipped) This feature helps to prevent you from unintentionally locking your intelligent access key inside your vehicle’s passenger compartment or rear cargo area. When you lock your vehicle using the power door lock control (with the door open, vehicle in park and ignition off), your vehicle will search for an intelligent access key in the passenger compartment after you close the door. If your vehicle finds a key, all of the doors will immediately unlock.

61

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Locks

The illuminated entry system will turn off the lights if: • •

you start your vehicle, you press the remote control lock button, or after 25 seconds of illumination.

• The lights will not turn off if: •

25 seconds elapse, or you lock your vehicle from the outside.

you turn them on with the lamp control, or • any door is open. Illuminated Exit The interior lamps and select exterior lamps will illuminate when all doors are closed and you switch the ignition off. The lamps will turn off if all the doors remain closed and: • • Battery Saver If you leave the courtesy lamps or dome lamps on and switch the ignition off, the battery saver shuts them off after some time. Accessory Mode Battery Saver for Intelligent Access Keys (If Equipped) If you leave the ignition on after leaving your vehicle, it will shut off 15 minutes after you close all of the doors.

Enabling or Disabling Autolock and Autounlock Note: Your authorized dealer can perform this procedure, or you can do the procedure yourself. To enable or disable these features, do the following: Note: You will have 30 seconds to complete the procedure. 1. Switch the ignition on. 2. Press the power door unlock button

three times.

3. Switch the ignition off. 4. Press the power door unlock button

three times.

5. Switch the ignition on. The horn will

sound indicating your vehicle is in programming mode.

Autolock: Press the power door unlock button then the lock button. The horn will sound once if disabled or twice (one short and one long) if enabled. Autounlock: Press the power door lock button then the unlock button. The horn will sound once if disabled or twice (one short and one long) if enabled. After programming the feature, switch the ignition off. The horn will sound once indicating programming is complete. Note: You can enable or disable the autounlock feature independently of the autolock feature. Illuminated Entry The interior lamps and select exterior lamps will illuminate when you unlock the doors with the remote entry system.

62

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Locks

Opening the Liftgate Manually

MANUAL LIFTGATE WARNINGS

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety belt properly. Failure to follow this warning could result in serious personal injury or death.

Press the button located in the top of the liftgate pull cup handle to unlatch the liftgate, and then pull on the outside handle. With the Remote Control

Press the button twice within three seconds.

Closing the Liftgate

Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not hang anything, for example a bike rack, from the glass or liftgate. This could damage the liftgate and its components. Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components.

A handle is located inside the liftgate to help with closing.

63

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138632E138630E155976Locks

•

•

•

The ignition is on and the transmission is not in park (P). The battery voltage is below the minimum operating voltage. The vehicle speed is at or above 1 mph (1 km/h).

If the liftgate starts to close after it has fully opened, this indicates there may be excessive weight on the liftgate or a possible gas strut failure. A repetitive chime sounds and the liftgate closes under control. Remove any excessive weight from the liftgate. If the liftgate continues to close after opening, have the system checked by an authorized dealer. Opening and Closing the Liftgate

WARNING

Make sure all persons are clear of the power liftgate area before using the power liftgate control.

Note: Be careful when opening or closing the liftgate in a garage or other enclosed area to avoid damaging the liftgate. Note: Do not leave the liftgate open while driving. This could damage the liftgate and its components. From the Instrument Panel

Press the button on the instrument panel.

With the Remote Control

Press the button twice within three seconds.

POWER LIFTGATE (If Equipped)

WARNINGS

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a crash, people riding in

these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Make sure everyone in your vehicle is in a seat and properly using a safety belt. Failure to follow this warning could result in serious personal injury or death.

Make sure to close and latch the liftgate to prevent drawing exhaust fumes into your vehicle. This will also prevent passengers and cargo from falling out. If you must drive with the liftgate open, keep the vents or windows open so outside air comes into your vehicle. Failure to follow this warning could result in serious personal injury.

Keep keys out of reach of children. Do not allow children to operate or play near an open or moving power

liftgate. You should supervise the operation of the power liftgate at all times.

Note: Make sure that you close the liftgate before operating or moving your vehicle, especially in an enclosure, like a garage or a parking structure. This could damage the liftgate and its components. Note: Do not hang anything, for example a bike rack, from the glass or liftgate. This could damage the liftgate and its components. The liftgate only operates with the transmission in park (P). Three warning tones sound once as the liftgate begins to power close. Five short chimes indicate a problem with the open or close request, caused by:

64

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E189530E138630Locks

With the Outside Control Button Opening the Liftgate 1. Unlock the liftgate with the remote

control or power door unlock control. If an intelligent access key is within 3 ft (1 m) of the liftgate, the liftgate unlocks when you press the liftgate release button.

Press and release the liftgate control button. Stopping the Liftgate Movement You can stop the liftgate movement by doing any of the following: • Pressing the liftgate control button. • Pressing the liftgate button on the

remote control twice.

• Pressing the liftgate button on the

instrument panel.

• Activating the obstacle detection

feature.

• Moving your foot under and away from the center rear bumper in a single-kick motion.*

*This method only works for vehicles with the hands-free liftgate feature. Setting the Liftgate Open Height 1. Open the liftgate. 2. Stop the liftgate by pressing the control button on the liftgate when it reaches the desired height.

Note: When the liftgate has stopped moving, you can also manually move it to the desired height.

2. Press the button in the top of the

liftgate pull-cup handle.

Note: Allow the system to open the liftgate. Manually pushing or pulling the liftgate may turn on obstacle detection and stop the power operation or reverse its direction. Manually interfering with the liftgate motion may also replicate a gas strut failure. Closing the Liftgate

WARNING

Keep clear of the liftgate when activating the rear switch.

65

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138632E138636Locks

When Opening The system stops when it detects an obstacle and two short tones sound. When you remove the obstacle, you can continue to operate the liftgate. Hands-Free Feature (If Equipped) Make sure you have an intelligent access transmitter within 3 ft (1 m) of the liftgate.

1. Move your foot under and away from

the rear bumper detection area in a single-kick motion. Do not move your foot sideways or the sensors may not detect the motion.

2. The liftgate powers open or close. Note: Allow the power system to open the liftgate. Manually pushing or pulling the liftgate may activate the system’s obstacle detection feature and stop the power operation or reverse its direction. Manually interfering with the liftgate motion may also replicate a gas strut failure. Note: Splashing water may cause the hands-free liftgate to open. Keep the intelligent access key away from the rear bumper detection area when washing your vehicle.

3. Press and hold the liftgate control button on the liftgate until a tone sounds, indicating programming is complete.

Note: You can only use the liftgate control button to program the height. Note: You cannot program the height if the liftgate position is too low. The new open liftgate height is recalled when the power liftgate is opened. To change the programmed height, repeat the above procedure. Once you open the power liftgate, you can manually move it to a different height. Note: The system recalls the new programmed height, even if you disconnect the battery. When operating the power liftgate after you have programmed a lower height than fully open, you can fully open the liftgate by manually pushing it upward to the maximum open position. Obstacle Detection When Closing The system stops when it detects an obstacle. Two short tones sound and the system reverses to open. When you remove the obstacle, you can power close the liftgate. Note: Entering your vehicle while the liftgate is closing can cause your vehicle to bounce and activate obstacle detection. To prevent this, let the power liftgate close completely before you enter your vehicle. Before driving off, check the instrument cluster for a liftgate or door ajar message or warning indicator. Failure to do this could result in unintentionally leaving the liftgate open while driving.

66

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E16160221Locks

2. Press 1·2 on the keypad within five

seconds.

3. Enter your personal five-digit code. You

must enter each number within five seconds of each other.

4. Press 1·2 on the keypad to save

personal code 1.

The doors will lock then unlock to confirm that programming was successful. To program additional personal entry codes, repeat Steps 1-3, then for Step 4: • • • • Tips: • Do not set a code that uses five of the

press 3·4 to save personal code 2
press 5·6 to save personal code 3
press 7·8 to save personal code 4
press 9·0 to save personal code 5.

same number.

• Do not use five numbers in sequential

order. The factory-set code will work even if you have set your own personal code.

•

Erasing a Personal Code 1. Enter the factory-set five-digit code. 2. Press and release 1·2 on the keypad

within five seconds.

3. Press and hold 1·2 for two seconds.

This must be done within five seconds of completing Step 2.

All personal codes will erase and only the factory-set five-digit code will work. Anti-Scan Feature The keypad will go into an anti-scan mode if you enter the wrong code seven times (35 consecutive button presses). This mode disables the keypad for one minute and the keypad lamp will flash.

KEYLESS ENTRY (If Equipped) SECURICODE™ KEYLESS ENTRY KEYPAD The keypad is located near the driver window. It is invisible until touched and then it lights up so you can see and touch the appropriate buttons. Note: If you enter your entry code too fast on the keypad, the unlock function may not work. Re-enter your entry code more slowly.

You can use the keypad to: • lock or unlock the doors program and erase user codes • • arm and disarm the anti-theft alarm. You can operate the keypad with the factory-set five-digit entry code. The code is located on the owner’s wallet card in the glove box and is available from an authorized dealer. You can also create up to five of your own five-digit personal entry codes. Programming a Personal Entry Code To create your own personal entry code: 1. Enter the factory-set code.

67

Escape (TM2) Canada/United States of America, enUSA, Second Printing

E138637Locks

The anti-scan feature will turn off after: • •

one minute of keypad inactivity pressing the unlock button on the remote control switching the ignition on unlocking the vehicle using intelligent access.

• •

Unlocking and Locking the Doors To Unlock the Driver Door Enter the factory-set five-digit code or your personal code. You must press each number within five seconds of each other. The interior lamps will illuminate. Note: All doors will unlock if the two-stage unlocking feature is disabled. See Locking and Unlocking (page 59). To Unlock All Doors Enter the factory-set code or your personal code, then press 3·4 control within five seconds. To Lock All Doors Press and hold 7·8 and 9·0 at the same time with the driver door closed. You do not need to enter the keypad code first.

68

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Security

PASSIVE ANTI-THEFT SYSTEM Note: The system is not compatible with non-Ford aftermarket remote start systems. Use of these systems may result in vehicle starting problems and a loss of security protection. Note: Metallic objects, electronic devices or a second coded key on the same key chain may cause vehicle starting problems if they are too close to the key when starting the engine. Prevent these objects from touching the coded key while starting the engine. Switch the ignition off, move all objects on the key chain away from the coded key and restart the engine if a problem occurs. Note: Do not leave a duplicate coded key in the vehicle. Always take your keys and lock all doors when leaving the vehicle. SecuriLock® The system is an engine immobilization system. It is designed to help prevent the engine from being started unless a coded key programmed to your vehicle is used. Using the wrong key may prevent the engine from starting. A message may appear in the information display. If you are unable to start the engine with a correctly coded key, a malfunction has happened and a message may appear in the information display. Automatic Arming The vehicle arms immediately after you switch the ignition off. Automatic Disarming Switching the ignition on with a coded key disarms the vehicle.

Replacement Keys Note: Your vehicle comes equipped with two integrated keyhead transmitters or two intelligent access keys. The integrated keyhead transmitter functions as a programmed ignition key that operates all the locks and starts the vehicle, as well as a remote control. The intelligent access key functions as a programmed key that operates the driver door lock and activates the intelligent access with push button start system, as well as a remote control. If your programmed transmitters or standard SecuriLock coded keys (integrated keyhead transmitters only) are lost or stolen and you do not have an extra coded key, you will need to have your vehicle towed to an authorized dealer. You need to erase the key codes from your vehicle and program new coded keys. Store an extra programmed key away from the vehicle in a safe place to help prevent any inconveniences. See your authorized dealer to purchase additional spare or replacement keys. Programming a Spare Integrated Keyhead Transmitter Note: You can program a maximum of eight coded keys to your vehicle. All eight can be integrated keyhead transmitters. You can program your own integrated keyhead transmitter or standard SecuriLock coded keys to your vehicle. This procedure will program both the engine immobilizer keycode and the remote entry portion of the remote control to your vehicle Only use integrated keyhead transmitters or standard SecuriLock keys.

69

Escape (TM2) Canada/United States of America, enUSA, Second Printing

Security

You must have two previously programmed coded keys and the new unprogrammed key readily accessible. See your authorized dealer to have the spare key programmed if two previously programmed coded keys are not available. Read and understand the entire procedure before you begin. 1.

Insert the first previously programmed coded key into the ignition.

2. Switch the ignition from off to on. Keep

the ignition on for at least three seconds, but no more than 10 seconds. 3. Switch the ignition off and remove the