2010 Dodge Challenger SRT8 Owners Manual

Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution.

Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system. If you notice a change in the sound of the exhaust system; or if the exhaust fumes can be detected inside the vehicle; or when the underside or rear of the vehicle is damaged; have an authorized technician inspect the complete ex- haust system and adjacent body areas for broken, dam- aged, deteriorated, or mispositioned parts. Open seams or loose connections could permit exhaust fumes to seep

into the passenger compartment. In addition, inspect the exhaust system each time the vehicle is raised for lubri- cation or oil change. Replace as required.

WARNING!

• Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, refer to “Safety Tips/Exhaust Gas” in “Things To Know Before Starting Your Vehicle” for further information. • A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your exhaust system. Do not park or operate your ve- hicle in areas where your exhaust system can contact anything that can burn.

CAUTION!

• The catalytic converter requires the use of un- leaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emissions con- trol device and may seriously reduce engine per- formance and cause serious damage to the engine. • Damage to the catalytic converter can result if your vehicle is not kept in proper operating condition. In the event of engine malfunction, particularly involving engine misfire or other apparent loss of performance, have your vehicle serviced promptly. Continued operation of your vehicle with a severe malfunction could cause the converter to overheat, resulting in possible damage to the converter and vehicle.

MAINTAINING YOUR VEHICLE 357
Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage. NOTE: systems can result against you. In unusual situations involving grossly malfunctioning engine operation, a scorching odor may suggest severe and abnormal catalyst overheating. If this occurs, stop the vehicle, turn off the engine and allow it to cool. Service, including a tune-up to manufacturer’s specifica- tions, should be obtained immediately.

Intentional tampering with emissions control in civil penalties being assessed

358 MAINTAINING YOUR VEHICLE To minimize the possibility of catalytic converter dam- age: • Do not shut off the engine or interrupt the ignition, when the transmission is in gear and the vehicle is in motion. • Do not try to start the engine by pushing or towing the • Do not idle the engine with any spark plug wires disconnected or removed, such as when diagnostic testing, or for prolonged periods during very rough idle or malfunctioning operating conditions.

vehicle.

Cooling System

WARNING!

• When working near the radiator cooling fan, dis- connect the fan motor lead or turn the ignition switch to the LOCK position (OFF position for Keyless Go™). The fan is temperature controlled and can start at any time the ignition switch is in the ON position (RUN position for Keyless Go™). • You or others can be badly burned by hot coolant or steam from your radiator. If you see or hear steam coming from under the hood, do not open the hood until the radiator has had time to cool. Never try to open a cooling system pressure cap when the radiator is hot.

Coolant Checks Check the engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the system should be drained, flushed, and refilled with fresh coolant. Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently spraying water from a garden hose vertically down the face of the condenser. Check the coolant recovery bottle tubing for brittle rub- ber, cracking, tears, cuts, and tightness of the connection at the bottle and radiator. Inspect the entire system for leaks. With the engine at normal operating temperature (but not running), check the cooling system pressure cap for proper vacuum sealing by draining a small amount of coolant from the radiator drain cock. If the cap is sealing properly, the engine coolant (antifreeze) will begin to

MAINTAINING YOUR VEHICLE 359
drain from the coolant recovery bottle. DO NOT RE- MOVE THE COOLANT PRESSURE CAP WHEN THE COOLING SYSTEM IS HOT. Cooling System – Drain, Flush, and Refill If the solution is dirty or contains a considerable amount of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove all deposits and chemicals. Properly dispose of the old antifreeze solution. Refer to “Maintenance Schedule” for further information. Selection of Coolant Use only the manufacturer’s recommended coolant. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.

360 MAINTAINING YOUR VEHICLE

CAUTION!

• Mixing of coolants other than specified HOAT engine coolants may result in engine damage and may decrease corrosion protection. If a non-HOAT coolant is introduced into the cooling system in an emergency, it should be replaced with the speci- fied coolant as soon as possible. • Do not use plain water alone or alcohol-based engine coolant (antifreeze) products. Do not use additional rust inhibitors or antirust products, as they may not be compatible with the radiator engine coolant and may plug the radiator. • This vehicle has not been designed for use with propylene glycol-based coolants. Use of propylene glycol-based coolants is not recommended.

Adding Coolant Your vehicle has been built with an improved engine coolant (antifreeze) that allows extended maintenance intervals. This engine coolant (antifreeze) can be used up to five years or 102,000 miles (170 000 km) before replacement. To prevent reducing this extended mainte- nance period, it is important that you use the same engine coolant (antifreeze) throughout the life of your vehicle. Please review these recommendations for using Hybrid Organic Additive Technology (HOAT) engine coolant (antifreeze). When adding engine coolant (antifreeze): • The manufacturer

recommends using MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Organic Additive Technology) or equivalent.

• Mix a minimum solution of 50% HOAT engine coolant and distilled water. Use higher concentrations (not to exceed 70%) if temperatures below −34°F (−37°C) are anticipated. • Use only high purity water such as distilled or deion- ized water when mixing the water/engine coolant (antifreeze) solution. The use of lower quality water will reduce the amount of corrosion protection in the engine cooling system.

Please note that it is the owner’s responsibility to main- tain the proper level of protection against freezing ac- cording to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing engine coolant (antifreeze) types will decrease the life of the engine coolant (antifreeze) and will require more frequent coolant changes.

MAINTAINING YOUR VEHICLE 361

Cooling System Pressure Cap The cap must be fully tightened to prevent loss of coolant and to ensure that coolant will return to the radiator from the coolant recovery bottle. The cap should be inspected and cleaned if there is any accumulation of foreign material on the sealing surfaces.

WARNING!

• The warning words “DO NOT OPEN HOT” on the cooling system pressure cap are a safety pre- caution. Never add coolant when the engine is overheated. Do not loosen or remove the cap to cool an overheated engine. Heat causes pressure to build up in the cooling system. To prevent scald- ing or injury, do not remove the pressure cap while the system is hot or under pressure.

(Continued)

362 MAINTAINING YOUR VEHICLE

WARNING! (Continued)

• Do not use a pressure cap other than the one specified for your vehicle. Personal injury or en- gine damage may result.

Disposal of Used Coolant Used ethylene glycol-based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. To prevent ingestion by animals or children, do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground. If ingested by a child or pet, seek emergency assistance immediately. Clean up any ground spills immediately. Coolant Level The coolant bottle provides a quick visual method for determining that the coolant level is adequate. With the

engine OFF and cold, the level of the coolant in the bottle should be between the ranges indicated on the bottle. The radiator normally remains completely full, so there is no need to remove the radiator cap unless checking for coolant freeze point or replacing coolant. Advise your service attendant of this. As long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. When additional coolant is needed to maintain the proper level, it should be added to the coolant bottle. Do not overfill. Points to Remember NOTE: When the vehicle is stopped after a few miles (kilometers) of operation, you may observe vapor coming from the front of the engine compartment. This is nor- mally a result of moisture from rain, snow, or high

humidity accumulating on the radiator and being vapor- ized when the thermostat opens, allowing hot coolant to enter the radiator. If an examination of your engine compartment shows no evidence of radiator or hose leaks, the vehicle may be safely driven. The vapor will soon dissipate. • Do not overfill the coolant recovery bottle. • Check the coolant freeze point in the radiator and in the coolant recovery bottle. If antifreeze needs to be added, the contents of the coolant recovery bottle must also be protected against freezing. • If frequent coolant additions are required, or if the level in the coolant recovery bottle does not drop when the engine cools, the cooling system should be pres- sure tested for leaks.

MAINTAINING YOUR VEHICLE 363

• Maintain coolant concentration at 50% HOAT engine coolant (minimum) and distilled water for proper corrosion protection of your engine, which contains aluminum components. • Make sure that the radiator and coolant recovery bottle overflow hoses are not kinked or obstructed. • Keep the front of the radiator clean. If your vehicle is equipped with air conditioning, keep the front of the condenser clean. • Do not change the thermostat for Summer or Winter install operation. If replacement is ever necessary, ONLY the correct type thermostat. Other designs may result in unsatisfactory coolant performance, poor gas mileage, and increased emissions.

364 MAINTAINING YOUR VEHICLE Brake System In order to assure brake system performance, all brake system components should be inspected periodically. Refer to “Maintenance Schedule” for further information.

WARNING!

Riding the brakes can lead to brake failure and possibly an accident. Driving with your foot resting or riding on the brake pedal can result in abnormally high brake temperatures, excessive lining wear, and possible brake damage. You would not have your full braking capacity in an emergency.

Master Cylinder – Brake Fluid Level Check Check the fluid level in the master cylinder immediately if the “Brake Warning Light” indicates system failure. Check the fluid level in the master cylinder when per- forming underhood services.

Clean the top of the master cylinder area before removing the cap. Add fluid to bring the level up to the “MAX” mark on the side of the master cylinder reservoir. Overfilling of fluid is not recommended because it may cause leaking in the system. Add enough fluid to bring the level up to the require- ments described on the brake fluid reservoir. With disc brakes, fluid level can be expected to fall as the brake pads wear. However, low fluid level may be caused by a leak and a checkup may be needed. Use only manufacturer’s recommended brake fluid. Re- fer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.

WARNING!

• Use only manufacturer’s recommended brake fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Using the wrong type of brake fluid can severely damage your brake system and/or impair its performance. The proper type of brake fluid for your vehicle is also labeled on the origi- nal factory installed hydraulic master cylinder reservoir.

(Continued)

MAINTAINING YOUR VEHICLE 365

WARNING! (Continued)

• To avoid contamination from foreign matter or moisture, use only new brake fluid or fluid that has been in a tightly closed container. Keep the master cylinder reservoir cap secured at all times. Brake fluid in a open container absorbs moisture from the air resulting in a lower boiling point. This may cause it to boil unexpectedly during hard or prolonged braking, resulting in sudden brake failure. This could result in a accident. • Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts, causing the brake fluid to catch fire. Brake fluid can also damage painted and vinyl surfaces, care should be taken to avoid its contact with these surfaces.

(Continued)

366 MAINTAINING YOUR VEHICLE

WARNING! (Continued)

• Do not allow petroleum based fluid to contami- nate the brake fluid. Brake seal components could be damaged, causing partial or complete brake failure. This could result in an accident.

Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture. Clutch Hydraulic System (Manual Transmission) – If Equipped The clutch hydraulic system is fed by a segregated volume of fluid within the brake system master cylinder reservoir. In the event of leakage or wear, use only the manufacturer’s recommended brake fluid. Refer to “Flu- ids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information.

Manual Transmission – If Equipped

Fluid Level Check Check the fluid level by removing the fill plug on the left side of the transmission. The fluid level should be at the bottom of the fill hole. Add fluid, if necessary, to maintain the proper level. Refer to “Fluids, Lubricants, and Genu- ine Parts” in “Maintaining Your Vehicle” for further information. Change Transmission Fluid If contaminated with water, change the fluid immedi- ately. See your authorized dealer for service. Refer to “Maintenance Schedule” for further information.

Automatic Transmission – If Equipped

Fluid Level Check Regular automatic transmission fluid level checks are not required. For this reason, the dipstick is omitted. If you notice fluid loss or gear shift malfunction, have your authorized dealer check the transmission fluid level.

CAUTION!

• Using a transmission fluid other than the manufac- turer’s recommended fluid may cause deterioration in transmission shift quality and/or torque converter shudder. Using a transmission fluid other than that recommended by the manufacturer will result in more frequent fluid and filter changes. Refer to “Fluids, Lubricants, and Genuine Parts” in “Main- taining Your Vehicle” for further information.

(Continued)

MAINTAINING YOUR VEHICLE 367

CAUTION! (Continued)

• The fluid level is preset at the factory and it does not require adjustment under normal operating conditions. If a transmission fluid leak occurs, visit your authorized dealer immediately. Severe damage to the transmission may occur. Your au- thorized dealer has the proper tools to adjust the fluid level accurately.

Fluid and Filter Changes Refer to “Maintenance Schedule” for further information. If the transmission is disassembled for any reason, the fluid and filter should be changed.

368 MAINTAINING YOUR VEHICLE Selection of Lubricant It is important that the proper lubricant is used in the transmission to assure optimum transmission perfor- mance. Use only manufacturer’s recommended transmis- sion fluid. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further informa- tion. It is important that the transmission fluid be main- tained at the prescribed level using the recommended fluid. No chemical flushes should be used in any trans- mission; only the approved lubricant may be used. Special Additives Automatic Transmission Fluid (ATF) is an engineered product and its performance may be impaired by supple- mental additives. Therefore, do not add any fluid addi- tives to the transmission. The only exception to this policy is the use of special dyes to aid in detecting fluid leaks. In addition, avoid using transmission sealers as they may adversely affect seals.

CAUTION!

Do not use chemical flushes in your transmission as the chemicals can damage your transmission compo- nents. Such damage is not covered by the New Vehicle Limited Warranty.

Rear Axle

Fluid Level Check Check the fluid level by removing the fill plug on the axle. The fluid level should be at the bottom of the fill hole. Add fluid, if necessary, to maintain the proper level. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. Change Axle Fluid Refer to “Maintenance Schedule” for further information.

Appearance Care and Protection from Corrosion

Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and chemicals that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle. Outside parking, which exposes your vehicle to airborne contami- nants, road surfaces on which the vehicle is operated, extreme hot or cold weather and other extreme condi- tions will have an adverse effect on paint, metal trim, and underbody protection. The following maintenance recommendations will enable you to obtain maximum benefit from the corrosion resistance built into your vehicle. What Causes Corrosion? Corrosion is the result of deterioration or removal of paint and protective coatings from your vehicle.

MAINTAINING YOUR VEHICLE 369

The most common causes are: • Road salt, dirt, and moisture accumulation. • Stone and gravel impact. • Insects, tree sap, and tar. • Salt in the air near seacoast localities. • Atmospheric fallout/industrial pollutants. Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using MOPAR威 Car Wash or equiva- lent, or a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar, or other similar deposits have accumu- lated on your vehicle, use MOPAR威 Super Kleen Bug and Tar Remover or equivalent to remove.

370 MAINTAINING YOUR VEHICLE

• Use a high quality cleaner wax, such as MOPAR威 Cleaner Wax or equivalent to remove road film, stains and to protect your paint finish. Take care never to scratch the paint. • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish.

CAUTION!

• Do not use abrasive or strong cleaning materials such as steel wool or scouring powder that will scratch metal and painted surfaces. • Use of power washers exceeding 1,200 psi (8 274 kPa) can result in damage or removal of paint and decals.

Special Care • If you drive on salted or dusty roads or if you drive near the ocean, hose off the undercarriage at least once a month. • It is important that the drain holes in the lower edges of the doors, rocker panels, and trunk be kept clear and open. • If you detect any stone chips or scratches in the paint, touch them up immediately. The cost of such repairs is considered the responsibility of the owner. • If your vehicle is damaged due to an accident or similar cause that destroys the paint and protective coating, have your vehicle repaired as soon as pos- sible. The cost of such repairs is considered the respon- sibility of the owner.

• If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider • Use MOPAR威 Touch Up Paint or equivalent on scratches as soon as possible. Your authorized dealer has touch up paint to match the color of your vehicle.

mud or stone shields behind each wheel.

Wheel and Wheel Trim Care All wheels and wheel trim, especially aluminum and chrome-plated wheels should be cleaned regularly with a mild soap and water to prevent corrosion. To remove heavy soil and/or excessive brake dust, use MOPAR威 Wheel Cleaner or equivalent or select a nonabrasive, non-acidic cleaner. Do not use scouring pads, steel wool, a bristle brush, or metal polishes. Only MOPAR威 or equivalent is recommended. Do not use oven cleaner.

MAINTAINING YOUR VEHICLE 371
Avoid automatic car washes that use acidic solutions or harsh brushes that may damage the wheels’ protective finish. Stain Repel Fabric Cleaning Procedure – If Equipped Stain Repel seats may be cleaned in the following man- ner: • Remove as much of the stain as possible by blotting • Blot any remaining stain with a clean, damp towel. • For tough stains, apply MOPAR威 Total Clean or equivalent, or a mild soap solution to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue.

with a clean, dry towel.

372 MAINTAINING YOUR VEHICLE

• For grease stains, apply MOPAR威 Multi-Purpose Cleaner or equivalent to a clean, damp cloth and remove the stain. Use a fresh, damp towel to remove soap residue. • Do not use any harsh solvents or any other form of

protectants on Stain Repel products.

Interior Care Use MOPAR威 Fabric Cleaner or equivalent to clean fabric upholstery and MOPAR威 Carpet Cleaner or equivalent for carpeting. Interior Trim should be cleaned starting with a damp cloth, or MOPAR威 Satin Select or equivalent. Do not use harsh cleaners or Armor All威. Use MOPAR威 Total Clean or equivalent to clean vinyl upholstery. MOPAR威 Total Clean or equivalent is specifically recom- mended for leather upholstery.

Your leather upholstery can be best preserved by regular cleaning with a damp soft cloth. Small particles of dirt can act as an abrasive and damage the leather upholstery and should be removed promptly with a damp cloth. Stubborn soils can be removed easily with a soft cloth and MOPAR威 Total Clean or equivalent. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, detergents, or ammonia-based cleaners to clean your leather upholstery. Application of a leather condi- tioner is not required to maintain the original condition.

WARNING!

Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in closed areas they may cause respiratory harm.

Cleaning Headlights Your vehicle has plastic headlights that are lighter and less susceptible to stone breakage than glass headlights. Plastic is not as scratch resistant as glass; and therefore, different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other aggressive material to clean the lenses. Glass Surfaces All glass surfaces should be cleaned on a regular basis with MOPAR威 Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning the inside rear win- dow equipped with electric defrosters or the right rear

MAINTAINING YOUR VEHICLE 373
quarter window equipped with the radio antenna. Do not use scrapers or other sharp instruments that may scratch the elements. When cleaning the rear view mirror, spray cleaner on the towel or rag that you are using. Do not spray cleaner directly on the mirror. Cleaning Plastic Instrument Cluster Lenses The lenses in front of the instruments in this vehicle are molded in clear plastic. When cleaning the lenses, care must be taken to avoid scratching the plastic. 1. Clean with a wet soft rag or micro-fiber towel. A mild soap solution may be used, but do not use high alcohol content or abrasive cleaners. If soap is used, wipe clean with a clean damp rag. 2. Dry with a soft tissue.

FUSES

Integrated Power Module (IPM) The Integrated Power Module (IPM) is located in the engine compartment. This module contains fuses and relays.

374 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye, or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the belts need cleaning, use MOPAR威 Total Clean or equivalent, a mild soap solution, or lukewarm water. Do not remove the belts from the vehicle to wash them. Replace the belts if they appear frayed or worn or if the buckles do not work properly. Cleaning The Center Console Cupholders Clean with a damp cloth or towel using a mild detergent with the cupholder in the center console. NOTE: The cupholder cannot be removed.

Integrated Power Module

CAUTION!

• When installing the integrated power module cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the integrated power module and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.

Cavity Car-

tridge Fuse —

—

—

—

— —

—

—

MAINTAINING YOUR VEHICLE 375

Mini- Fuse

15 Amp Blue 25 Amp Natural 25 Amp Natural 25 Amp Natural — 25 Amp Natural 25 Amp Natural 30 Amp Green

Description

Washer Motor

Powertrain Control Module (PCM) Ignition Run/Start

EGR Solenoid/ Alternator — Ignition Coils/Injectors

Headlamp Washer Relay – If Equipped Starter

376 MAINTAINING YOUR VEHICLE

Cavity Car-

Mini- Fuse

Description

Cavity Car-

10

11

12

13

14
15

tridge Fuse — 30 Amp Pink 30 Amp Pink 40 Amp Green 50 Amp Red — 50 Amp Red

— —

—

—

—

— —

16
17
18
19
20
21
22

— Windshield Wiper

Anti-Lock Brake System (ABS) Valves Radiator Fan Lo/High

Anti-Lock Brake System (ABS) Pump Motor — Radiator Fan

tridge Fuse — — — — — — —

Mini- Fuse

Description

— — — — — — —

— — — — — — —

Rear Power Distribution Center There is also a power distribution center located in the trunk under the spare tire access panel. This center contains fuses and relays.

MAINTAINING YOUR VEHICLE 377

Rear Power Distribution Center

Access Panel

378 MAINTAINING YOUR VEHICLE

CAUTION!

• When installing the power distribution center cover, it is important to ensure the cover is prop- erly positioned and fully latched. Failure to do so may allow water to get into the power distribution center and possibly result in an electrical system failure. • When replacing a blown fuse, it is important to use only a fuse having the correct amperage rating. The use of a fuse with a rating other than indicated may result in a dangerous electrical system over- load. If a properly rated fuse continues to blow, it indicates a problem in the circuit that must be corrected.

Cavity Car-

Mini- Fuse

—

tridge Fuse 60 Amp Yellow

40 Amp Green — 40 Amp Green

—

— —

Description

Ignition Off Draw (IOD) Cavity 1 of the Rear Power Distribution Center contains a black IOD fuse needed for vehicle processing dur- ing assembly. The ser- vice replacement part is a 60 Amp yellow car- tridge fuse. Integrated Power Mod- ule (IPM) — Integrated Power Mod- ule (IPM)

Cavity Car-

tridge Fuse — —

Cavity Car-

tridge Fuse 30 Amp Pink —

10
11 * 12 *

—

—

—

— — —

Mini- Fuse

—

20 Amp Yellow 15 Amp Blue 15 Amp Blue

20 Amp Yellow — — —

Description

Heated Seats – If Equipped Fuel Pump

Sub Amp – If Equipped

Diagnostic Link Connec- tor (DLC)/Wireless Con- trol Module (WCM)/ Wireless Ignition Node (WIN) Power Outlet

— — —

13 * 14

15
16
17

18

19

20
21
22

— — —

—

—

— — —

MAINTAINING YOUR VEHICLE 379

Mini- Fuse

— 10 Amp Red

— — 20 Amp Yellow 20 Amp Yellow 10 Amp Red — — —

Description

— AC Heater Control/ Cluster/Security Mod- ule – If Equipped — — Cluster

Selectable Power Outlet

Stop Lights

— — —

380 MAINTAINING YOUR VEHICLE

Cavity Car-

23
24
25
26
27

28

29

Cavity Car-

tridge Fuse —

tridge Fuse — — — — —

—

—

Mini- Fuse

— — — — 10 Amp Red 10 Amp Red

5 Amp Orange

Description

— — — — Occupant Restraint Con- troller (ORC) Ignition Run, AC Heater Control/Occupant Re- straint Controller (ORC) Cluster/Electronic Sta- bility Program (ESP)/ Powertrain Control Module (PCM)/STOP LIGHT Switch

30

31
32
33
34
35

36

37

— — — — —

—

—

Mini- Fuse

10 Amp Red

— — — — 5 Amp Orange

25 Amp Natural

15 Amp Blue

Description

Door Modules/Power Mirrors/Steering Con- trol Module (SCM) — — — — Antenna Module – If Equipped/Power Mir- rors Hands-Free Phone – If Equipped/Radio/ Amplifier Feed Transmission

Cavity Car-

tridge Fuse —

—

—

Mini- Fuse

10 Amp Red

10 Amp Red 5 Amp Orange

— 30 Amp Pink 30 Amp Pink 20 Amp Blue

— —

—

—

Description

Cargo Light/Vehicle In- formation Module – If Equipped Heated Mirrors – If Equipped Auto Inside Rearview Mirror/Heated Seats – If Equipped/Switch Bank — Front Blower Motor

Rear Window Defroster

Amplifier/Sunroof – If Equipped

MAINTAINING YOUR VEHICLE 381
* Cavities 11, 12, and 13 contain self-resetting fuses (circuit breakers) that are only serviceable by an autho- rized dealer. The cluster and the driver seat switch are fused by the 25 Amp circuit breaker in cavity 11. The passenger seat switch is fused by the 25 Amp circuit breaker in cavity 12. The door modules, the driver power window switch, and the passenger power window switch are fused by the 25 Amp circuit breaker in cavity 13. If you experience temporary or permanent loss of these systems, see your authorized dealer for service.

VEHICLE STORAGE If you are leaving your vehicle dormant for more than 21 days, you may want to take these steps to protect your battery. • Disconnect the negative cable from the battery. • Anytime you store your vehicle, or keep it out of service (i.e., vacation) for two weeks or more, run the air conditioning system at idle for about five minutes

38

39

40

41
42

43

44

382 MAINTAINING YOUR VEHICLE

in the fresh air and high blower setting. This will ensure adequate system lubrication to minimize the possibility of compressor damage when the system is started again.

REPLACEMENT BULBS

LIGHT BULBS – Interior Bulb Number Rear Courtesy/Reading Lamps . . . . . . . . . . . . . W5W Rear Compartment (Trunk) Lamp . . . . . . . . . . . . . 562
Overhead Console Reading Lamps . . . . . . . . . . . . 578
Visor Vanity Lamps . . . . . . . . . . . . . . . . . . . . . A6220
Glove Box Lamp – If Equipped. . . . . . . . . . . . . . . 194
Door Courtesy . . . . . . . . . . . . . . . . . . . . . . . . . . 562
Shift Indicator Lamp . . . . . . . . . . . . . . . . . JKLE14140
Optional Door Map Pocket/Cupholder . . . . . . . . LED (Serviced at Authorized Dealer) NOTE: For lighted switches, see your authorized dealer for replacement instructions.

Bulb Number

All of the interior bulbs are glass wedge base or glass cartridge types. Aluminum base bulbs are not approved and should not be used for replacement. LIGHT BULBS – Exterior Low Beam Headlamp – High Intensity Discharge (HID) . . . . . . . . . . . . . . . . . . . . . . . . . D1S (Serviced at Authorized Dealer) High Beam Headlamp . . . . . . . . . . . . . . . . . . . . 9005
Front Park/Turn Lamp. . . . . . . . . . . . . . . . . . . 3157A Front Fog Lamp . . . . . . . . . . . . . . . . . . . . . . PSX24W (Serviced at Authorized Dealer) Front Side Marker . . . . . . . . . . . . . . . . . . . . . . . . 168
Tail Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3057K Tail/Stop/Turn Lamp . . . . . . . . . . . . . . . . . . . 3057K Rear Side Marker . . . . . . . . . . . . . . . . . . . . . . . . 168
Backup Lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 921
Center High-Mount Stop Lamp (CHMSL). . . . . . . LED (Serviced at Authorized Dealer) License. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 168

BULB REPLACEMENT

Low Beam Headlamp, High Beam Headlamp, Park/Turn Lamp — Models with Halogen Headlamps — If Equipped See your authorized dealer for bulb replacement. Low Beam Headlamp, High Beam Headlamp, and Park/Turn Lamp — Models with High Intensity Discharge (HID) Headlamps — If Equipped

HID Headlamps The headlamps are a type of high voltage discharge tube. High voltage can remain in the circuit even with the headlamp switch off and the key removed. Because of this, you should not attempt to service a headlamp bulb yourself. If a headlamp bulb fails, take your vehicle to an authorized dealer for service.

MAINTAINING YOUR VEHICLE 383

WARNING!

A transient high tension occurs at the bulb sockets of HID headlamps when the headlamp switch is turned ON. It may cause serious electrical shock or electro- cution if not serviced properly. See your authorized dealer for service.

NOTE: On vehicles equipped with HID headlamps, when the headlamps are turned on, there is a blue hue to the lamps. This diminishes and becomes more white after approximately 10 seconds, as the system charges. Front/Rear Side Marker Lamp

1. Remove the front/rear side marker. Use a fiber stick or similar tool to gently pry the lamp on the outboard side to disengage the clip.

Tail/Turn and Stop Lamp

1. Open the trunk. 2. Using a screwdriver, remove the tail lamp retainer.

384 MAINTAINING YOUR VEHICLE NOTE: • If a screwdriver is used, make sure a soft material is placed between the vehicle body and tool so not to scratch the paint.

2. Rotate the bulb’s socket counterclockwise, and remove the bulb and socket assembly from the housing. 3. Pull the bulb out of the socket and insert the replace- ment bulb. 4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place. 5. Reinstall the front/rear side marker.

3. Remove the fasteners from the back of the tail lamp assembly.

MAINTAINING YOUR VEHICLE 385
6. Pull the tail lamp assembly clear from the vehicle to access the bulbs.

4. Pull back the trunk liner. 5. Remove the remaining fasteners from the back of the tail lamp assembly.

7. Push the electrical connector locking tab to the side. 8. Disconnect the electrical connector.

386 MAINTAINING YOUR VEHICLE 9. Turn the appropriate bulb and socket assembly coun- terclockwise to remove it from the tail lamp assembly. 10. Disconnect the bulb from the socket assembly and install the replacement bulb. 11. Reinstall the bulb and socket assembly into the tail lamp assembly, and then turn it clockwise. 12. Reinstall the tail lamp assembly, fasteners, electrical connector, and trunk liner. 13. Reinstall tail lamp retainer.

14. Close the trunk. Center Tail/Backup Lamp See your authorized dealer for bulb replacement.

Center High-Mounted Stop Lamp (CHMSL) The CHMSL uses LED lamps that are not serviceable separately. The CHMSL must be replaced as an assembly, see your authorized dealer. License Lamp

1. Remove the screws securing the lamp to the rear fascia. 2. Remove the bulb and socket assembly. 3. Disconnect the bulb from the socket assembly and install the replacement bulb.

MAINTAINING YOUR VEHICLE 387

1 — License Lamp Bulb 2 — Socket 4. Reinstall the bulb and socket assembly. 5. Reattach the lamp to the rear fascia, and then install the screws.

388 MAINTAINING YOUR VEHICLE FLUID CAPACITIES

Fuel (Approximate) Engine Oil with Filter 6.1 Liter Engine (SAE 5W-40, API Certified) Cooling System * 6.1 Liter Engine (MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula or equivalent) * Includes heater and coolant recovery bottle filled to MAX level.

U.S.

19 Gallons

7 Quarts

Metric 72 Liters

6.6 Liters

15 Quarts

14.4 Liters

FLUIDS, LUBRICANTS, AND GENUINE PARTS

MAINTAINING YOUR VEHICLE 389

Engine Component Engine Coolant

Engine Oil

Engine Oil Filter Spark Plugs Fuel Selection

Fluid, Lubricant, or Genuine Part MOPAR威 Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. For best performance and maximum protection under all types of operat- ing conditions, the manufacturer only recommends full synthetic engine oils that meet the requirements of Chrysler Material Standard MS-10725
and are approved to MB 229.3 or MB 229.5. The manufacturer recom- mends the use of a full synthetic 5W-40 or equivalent engine oil. MOPAR威 Engine Oil Filter or equivalent. PLZTR5A-13 (Gap 0.040 in [1.01 mm]) Premium Unleaded 91 Octane Only or higher.

390 MAINTAINING YOUR VEHICLE Chassis Component Manual Transmission – If Equipped MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed

Fluid, Lubricant, or Genuine Part

Automatic Transmission – If Equipped Brake Master Cylinder

Power Steering Reservoir

Rear Axle

ATF+4威 product. MOPAR威 ATF+4威 Automatic Transmission Fluid or equivalent licensed ATF+4威 product. MOPAR威 DOT 3, SAE J1703 should be used. If DOT 3, SAE J1703 brake fluid is not available, then DOT 4 is acceptable. Use only recommended brake fluids. MOPAR威 Power Steering Fluid + 4, MOPAR威 ATF+4威 Automatic Trans- mission Fluid or equivalent licensed ATF+4威 product. MOPAR威 Synthetic Gear Lubricant SAE 75W90 (API GL-5) or equivalent (with MOPAR威 Friction Modifier — Hypoid Gear Additive).

MAINTENANCE SCHEDULES

CONTENTS

䡵 Emission Control System Maintenance . . . . . . 392
䡵 Maintenance Schedule . . . . . . . . . . . . . . . . . . 392

▫ Required Maintenance Intervals . . . . . . . . . . 394

M

392 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The Scheduled Maintenance services listed in bold type, must be done at the times or mileages specified to ensure the continued proper functioning of the Emission Control System. These, and all other maintenance services in- cluded in this manual, should be done to provide best vehicle performance and reliability. More frequent main- tenance may be needed for vehicles in severe operating conditions, such as dusty areas and very short trip driving. Inspection and service should also be done anytime a malfunction is suspected. NOTE: Maintenance, replacement, or repair of the emis- sions control devices and systems on your vehicle may be performed by any automotive repair establishment or individual using any automotive part that has been certified pursuant to U.S. EPA or in the State of Califor- nia, California Air Resources Board regulations.

Information Center

MAINTENANCE SCHEDULE The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance. On Electronic Vehicle (EVIC) equipped vehicles, “Oil Change Required” will be dis- played in the EVIC and a single chime will sound, indicating that an oil change is necessary. On Non-EVIC equipped vehicles, “Change Oil” will flash in the instrument cluster odometer and a single chime will sound, indicating that an oil change is necessary. Based on engine operation conditions, the oil change indicator message will illuminate. This means that ser- vice is required for your vehicle. Have your vehicle serviced as soon as possible, within the next 500 miles (805 km).

NOTE: • The oil change indicator message will not monitor the time since the last oil change. Change your vehicle’s oil if it has been six months since your last oil change, even if the oil change indicator message is NOT illuminated. • Change your engine oil more often if you drive your • Under no circumstances should oil change intervals exceed 6,000 miles (10,000 km) or six months, which- ever comes first.

vehicle off-road for an extended period of time.

Your authorized dealer will reset the oil change indicator message after completing the scheduled oil change. If a scheduled oil change is performed by someone other than your authorized dealer, the message can be reset by referring to the steps described under “Electronic Vehicle Information Center (EVIC)/Oil Change Required” in

MAINTENANCE SCHEDULES 393
“Understanding Your Instrument Panel” or under “In- strument Cluster Description/Odometer/Trip Odom- eter” in “Understanding Your Instrument Panel” for further information. At Each Stop for Fuel • Check the engine oil level. Refer to “Maintenance Procedures/Engine Oil” in “Maintaining Your Ve- hicle” for further information. • Check the windshield washer solvent and add if

required.

Once a Month • Check tire pressure and look for unusual wear or • Inspect the battery, and clean and tighten the terminals

damage.

as required.

Required Maintenance Intervals Refer to the Maintenance Schedules on the following pages for the required maintenance intervals.

394 MAINTENANCE SCHEDULES

• Check the fluid levels of the coolant reservoir, brake master cylinder, and power steering, and add as needed. • Check all lights and other electrical items for correct

operation.

At Each Oil Change • Change the engine oil filter. • Inspect the brake hoses and lines.

CAUTION!

Failure to perform the required maintenance items may result in damage to the vehicle.

6,000 Miles (10,000 km) or 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 395

12,000 Miles (20,000 km) or 12 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. Perform the first inspection at 12,000 miles (20 000 km) or

12 months.

❏ Inspect the exhaust system. Perform the first inspection at 12,000 miles (20 000 km) or

12 months.

❏ Inspect the manual transmission fluid (if equipped), add as necessary. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

396 MAINTENANCE SCHEDULES

18,000 Miles (30,000 km) or 18 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Inspect the rear axle fluid.

24,000 Miles (40,000 km) or 24 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the

following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

30,000 Miles (50,000 km) or 30 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Adjust parking brake on vehicles

equipped with four-wheel disc brakes.

MAINTENANCE SCHEDULES 397

36,000 Miles (60,000 km) or 36 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the rear axle fluid. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

398 MAINTENANCE SCHEDULES

42,000 Miles (70,000 km) or 42 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

MAINTENANCE SCHEDULES 399

48,000 Miles (80,000 km) or 48 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner filter, and replace if necessary. ❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for damage, wear, improper looseness or end play;

replace if necessary.

❏ Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet, or frequent trailer towing. ❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the following: Most of your driving is at sustained high

speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

M

400 MAINTENANCE SCHEDULES

54,000 Miles (90,000 km) or 54 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Inspect the rear axle fluid.

60,000 Miles (100,000 km) or 60 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. ❏ Change the automatic transmission fluid and filter if using your vehicle for any of the

following: police, taxi, fleet, or frequent trailer towing.

❏ Flush and replace the engine coolant at 60 months if not done at 102,000 miles

(170 000 km).

❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

66,000 Miles (110,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 401

72,000 Miles (120,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the rear axle fluid. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the

following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

402 MAINTENANCE SCHEDULES

78,000 Miles (130,000 km) or 78 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

84,000 Miles (140,000 km) or 84 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

90,000 Miles (150,000 km) or 90 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Inspect and replace the PCV Valve if

necessary.*

❏ Inspect the rear axle fluid. ❏ Adjust parking brake on vehicles

equipped with four-wheel disc brakes.

MAINTENANCE SCHEDULES 403

96,000 Miles (160,000 km) or 96 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

❏ Change the rear axle fluid if using your vehicle for any of the following: police, taxi, fleet,

or frequent trailer towing.

❏ Change the manual transmission fluid (if equipped).

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

M

404 MAINTENANCE SCHEDULES

102,000 Miles (170,000 km) or 102 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires. ❏ Replace the spark plugs. ❏ Flush and replace the engine coolant if

not done at 60 months.

108,000 Miles (180,000 km) or 108 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ If you are using your vehicle in dusty or off-road conditions, inspect the engine air cleaner

filter, and replace if necessary.

❏ Inspect the brake linings, and replace if necessary. ❏ Inspect the rear axle fluid. ❏ Inspect the manual transmission fluid (if equipped), add as necessary. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #

Date

Dealer Code

Signature Authorized Chrysler Dealer

Signature Authorized Chrysler Dealer

114,000 Miles (190,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil

filter.

❏ Rotate tires.

MAINTENANCE SCHEDULES 405

120,000 Miles (200,000 km) or 120 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate tires. ❏ Replace the engine air cleaner filter. ❏ Inspect the brake linings, and replace if necessary. ❏ Adjust parking brake on vehicles equipped with four-wheel disc brakes. ❏ Inspect the CV joints. ❏ Inspect the exhaust system. ❏ Inspect the front suspension, tie rod ends and boot seals for cracks or leaks and all parts for

damage, wear, improper looseness or end play; replace if necessary.

❏ Change the automatic transmission fluid and filter. ❏ Change the manual transmission fluid (if equipped) if using your vehicle for any of the

following: Most of your driving is at sustained high speeds during hot weather, above 90°F (32°C), driving in dusty conditions, or stop and go driving.

Odometer Reading

Repair Order #

Date

Dealer Code

Odometer Reading

Repair Order #