2013 Chevrolet Camaro Owners Manual

affects vehicle handling and ride comfort. Never load the vehicle with more weight than it was designed to carry.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (57,1)

When to Check Check the tires once a month or more. Do not forget the compact spare, if the vehicle has one. The cold compact spare tire pressure should be at 420 kPa (60 psi). See Compact Spare Tire on page 10‑85.

How to Check Use a good quality pocket-type gauge to check tire pressure. Proper tire inflation cannot be determined by looking at the tire. Check the tire inflation pressure when the tires are cold, meaning the vehicle has not been driven for at least three hours or no more than 1.6 km (1 mi). Remove the valve cap from the tire valve stem. Press the tire gauge firmly onto the valve to get a pressure measurement. If the cold tire inflation pressure matches the recommended

pressure on the Tire and Loading Information label, no further adjustment is necessary. If the inflation pressure is low, add air until the recommended pressure is reached. If the inflation pressure is high, press on the metal stem in the center of the tire valve to release air. Recheck the tire pressure with the tire gauge. Return the valve caps on the valve stems to prevent leaks and keep out dirt and moisture.

Tire Pressure for High-Speed Operation

{ WARNING

Driving at high speeds, 160 km/h (100 mph) or higher, puts an additional strain on tires. Sustained high-speed driving

(Continued)

Vehicle Care

10-57

WARNING (CONTINUED)

causes excessive heat buildup and can cause sudden tire failure. You could have a crash and you or others could be killed. Some high-speed rated tires require inflation pressure adjustment for high-speed operation. When speed limits and road conditions are such that a vehicle can be driven at high speeds, make sure the tires are rated for high-speed operation, in excellent condition, and set to the correct cold tire inflation pressure for the vehicle load.

Vehicles with 245/45ZR20 103Y, P245/50ZR19 104W, 275/ 40ZR20 106Y, 285/35ZR20 (100Y), and 305/35ZR20 (104Y) size tires, have tires capable of high speed use.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (58,1)

10-58

Vehicle Care

Make sure vehicles with 245/ 45ZR20 103Y, P245/50ZR19 104W and 275/40ZR20 106Y size tires are inflated to the recommended cold inflation pressures before operating the vehicle at speeds over 160 km/h (100 mph). See Vehicle Load Limits on page 9‑12 and Tire Pressure on page 10‑56. Make sure vehicles with 285/ 35ZR20 (100Y), and 305/35ZR20
(104Y) size tires are inflated to 300 kPa (44 psi) before operating the vehicle at speeds of 160 km/h (100 mph) or higher. Return the tires to the recommended cold tire inflation pressure when high-speed driving has ended. See Vehicle Load Limits on page 9‑12 and Tire Pressure on page 10‑56.

Tire Pressure Monitor System The Tire Pressure Monitor System (TPMS) uses radio and sensor technology to check tire pressure levels. The TPMS sensors monitor the air pressure in your tires and transmit tire pressure readings to a receiver located in the vehicle. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pressure label, you should determine the proper tire inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure monitoring system (TPMS) that illuminates a low tire

pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driving on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle's handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver's responsibility to maintain correct tire pressure, even if under-inflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (59,1)

The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevent the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. See Tire Pressure Monitor Operation on page 10‑59.

Federal Communications Commission (FCC) Rules and with Industry Canada Standards See Radio Frequency Statement on page 13‑21 for information regarding Part 15 of the Federal Communications Commission (FCC) Rules and with Industry Canada Standards RSS-GEN/210/220/310.

Tire Pressure Monitor Operation This vehicle may have a Tire Pressure Monitor System (TPMS). The TPMS is designed to warn the driver when a low tire pressure condition exists. TPMS sensors are mounted onto each tire and wheel assembly, excluding the spare tire and wheel assembly. The TPMS sensors monitor the air pressure in the tires and transmit the tire pressure readings to a receiver located in the vehicle.

Vehicle Care

10-59

When a low tire pressure condition is detected, the TPMS illuminates the low tire pressure warning light located on the instrument cluster. If the warning light comes on, stop as soon as possible and inflate the tires to the recommended pressure shown on the Tire and Loading Information label. See Vehicle Load Limits on page 9‑12. A message to check the pressure in a specific tire displays in the Driver Information Center (DIC) display. The low tire pressure warning light and the DIC warning message come on at each ignition cycle until the tires are inflated to the correct inflation pressure. Using the DIC, tire pressure levels can be viewed. For additional information and

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (60,1)

10-60

Vehicle Care

details about the DIC operation and displays see Driver Information Center (DIC) on page 5‑24. The low tire pressure warning light may come on in cool weather when the vehicle is first started, and then turn off as the vehicle is driven. This could be an early indicator that the air pressure is getting low and must be inflated to the proper pressure. A Tire and Loading Information label shows the size of the original equipment tires and the correct inflation pressure for the tires when they are cold. See Vehicle Load Limits on page 9‑12, for an example of the Tire and Loading Information label and its location. Also see Tire Pressure on page 10‑56. The TPMS can warn about a low tire pressure condition but it does not replace normal tire maintenance. See Tire Inspection on page 10‑62, Tire Rotation on page 10‑63 and Tires on page 10‑49.

Notice: Tire sealant materials are not all the same. A non-approved tire sealant could damage the TPMS sensors. TPMS sensor damage caused by using an incorrect tire sealant is not covered by the vehicle warranty. Always use only the GM-approved tire sealant available through your dealer or included in the vehicle. Factory-installed Tire Inflator Kits use a GM-approved liquid tire sealant. Using non-approved tire sealants could damage the TPMS sensors. See Tire Sealant and Compressor Kit on page 10‑72 for information regarding the inflator kit materials and instructions.

TPMS Malfunction Light and Message The TPMS will not function properly if one or more of the TPMS sensors are missing or inoperable. When the system detects a malfunction, the low tire warning light flashes for about one minute and then stays on for the remainder of the ignition cycle. A DIC warning message also displays. The malfunction light and DIC warning message come on at each ignition cycle until the problem is corrected. Some of the conditions that can cause these to come on are: . One of the road tires has been

replaced with the spare tire. The spare tire does not have a TPMS sensor. The malfunction light and DIC message should go off after the road tire is replaced and the sensor matching process is performed successfully. See "TPMS Sensor Matching Process" later in this section.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (61,1)

The TPMS sensor matching process was not done or not completed successfully after rotating the tires. The malfunction light and the DIC message should go off after successfully completing the sensor matching process. See "TPMS Sensor Matching Process" later in this section.

. One or more TPMS sensors are

missing or damaged. The DIC message and the malfunction light should go off when the TPMS sensors are installed and the sensor matching process is performed successfully. See your dealer for service.

. Replacement tires or wheels do not match the original equipment tires or wheels. Tires and wheels other than those recommended could prevent the TPMS from functioning properly. See Buying New Tires on page 10‑65.

. Operating electronic devices or being near facilities using radio wave frequencies similar to the TPMS could cause the TPMS sensors to malfunction.

If the TPMS is not functioning properly, it cannot detect or signal a low tire condition. See your dealer for service if the TPMS malfunction light and DIC message come on and stay on. TPMS Sensor Matching Process Each TPMS sensor has a unique identification code. The identification code needs to be matched to a new tire/wheel position after rotating the tires or replacing one or more of the TPMS sensors. The TPMS sensor matching process should also be performed after replacing a spare tire with a road tire containing the TPMS sensor. The malfunction light and the DIC message should go off at the next ignition cycle. The sensors are matched to the tire/ wheel positions, using a TPMS

Vehicle Care

10-61

relearn tool, in the following order: driver side front tire, passenger side front tire, passenger side rear tire, and driver side rear. See your dealer for service or to purchase a relearn tool. There are two minutes to match the first tire/wheel position, and five minutes overall to match all four tire/wheel positions. If it takes longer, the matching process stops and must be restarted. The TPMS sensor matching process is: 1. Set the parking brake. 2. Turn the ignition to ON/RUN with

the engine off.

3. Use the MENU button to select the Vehicle Information menu in the Driver Information Center (DIC).

4. Use the thumbwheel to scroll to

the Tire Pressure Menu item screen.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (62,1)

10-62

Vehicle Care

5. Press the SET/CLR button to

10. Proceed to the passenger side

rear tire, and repeat the procedure in Step 8.

11. Proceed to the driver side rear tire, and repeat the procedure in Step 8. The horn sounds two times to indicate the sensor identification code has been matched to the driver side rear tire, and the TPMS sensor matching process is no longer active. The TIRE LEARNING ACTIVE message on the DIC display screen goes off.

12. Turn the ignition to LOCK/OFF. 13. Set all four tires to the

recommended air pressure level as indicated on the Tire and Loading Information label.

begin the sensor matching process. A message requesting acceptance of the process should display.

6. Press the SET/CLR button again

to confirm the selection. The horn sounds twice to signal the receiver is in relearn mode and the TIRE LEARNING ACTIVE message displays on the DIC screen.

7. Start with the driver side

front tire.

8. Place the relearn tool against

the tire sidewall, near the valve stem. Then press the button to activate the TPMS sensor. A horn chirp confirms that the sensor identification code has been matched to this tire and wheel position.

9. Proceed to the passenger side

front tire, and repeat the procedure in Step 8.

Tire Inspection We recommend that the tires, including the spare tire, if the vehicle has one, be inspected for signs of wear or damage at least once a month. Replace the tire if: . The indicators at three or

more places around the tire can be seen.

. There is cord or fabric

showing through the tire's rubber.

. The tread or sidewall is

cracked, cut, or snagged deep enough to show cord or fabric.

. The tire has a bump, bulge,

or split.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (63,1)

. The tire has a puncture, cut, or other damage that cannot be repaired well because of the size or location of the damage.

Tire Rotation If the vehicle has non-directional tires, they should be rotated every 12 000 km/7,500 mi. See Maintenance Schedule on page 11‑2. Tires are rotated to achieve a uniform wear for all tires. The first rotation is the most important. Anytime unusual wear is noticed, rotate the tires as soon as possible and check for damaged tires or wheels. If the unusual wear continues after the rotation, check the wheel alignment.

Vehicle Care

10-63

Use this rotation pattern if the vehicle has different size tires on the front and rear and they are non-directional. Different tire sizes should not be rotated front to rear.

See When It Is Time for New Tires on page 10‑64 and Wheel Replacement on page 10‑69. Directional tires should not be rotated. Each tire and wheel should be used only in the position it is in. Directional tires will have an arrow on the tire indicating the proper direction of rotation or will have “left” or “right” molded on the sidewall.

Use this rotation pattern when rotating tires of the same size installed on all four wheel positions. If the vehicle has a compact spare tire, do not include it in the tire rotation.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (64,1)

10-64

Vehicle Care

Adjust the front and rear tires to the recommended inflation pressure on the Tire and Loading Information label after the tires have been rotated. See Tire Pressure on page 10‑56
and Vehicle Load Limits on page 9‑12. Reset the Tire Pressure Monitor System. See Tire Pressure Monitor Operation on page 10‑59. Check that all wheel nuts are properly tightened. See “Wheel Nut Torque” under Capacities and Specifications on page 12‑2.

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come (Continued)

WARNING (CONTINUED)

off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

Lightly coat the center of the wheel hub with wheel bearing grease after a wheel change or tire rotation to prevent corrosion or rust build-up. Do not get grease on the flat wheel mounting surface or on the wheel nuts or bolts.

When It Is Time for New Tires Factors such as maintenance, temperatures, driving speeds, vehicle loading, and road conditions affect the wear rate of the tires.

Treadwear indicators are one way to tell when it is time for new tires. Treadwear indicators appear when the tires have only 1.6 mm (1/16 in) or less of tread remaining. See Tire Inspection on page 10‑62 and Tire Rotation on page 10‑63.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (65,1)

The rubber in tires ages over time. This also applies to the spare tire, if the vehicle has one, even if it is never used. Multiple factors including temperatures, loading conditions, and inflation pressure maintenance affect how fast aging takes place. GM recommends that tires, including the spare if equipped, be replaced after six years, regardless of tread wear. The tire manufacturer date is the last four digits of the DOT Tire Identification Number (TIN) which is molded into one side of the tire sidewall. The first two digits represent the week (01–52) and the last two digits, the year. For example, the third week of the year 2010 would have a four-digit DOT date of 0310. Vehicle Storage Tires age when stored normally mounted on a parked vehicle. Park a vehicle that will be stored for at least a month in a cool, dry, clean area away from direct sunlight to

slow aging. This area should be free of grease, gasoline, or other substances that can deteriorate rubber. Parking for an extended period can cause flat spots on the tires that may result in vibrations while driving. When storing a vehicle for at least a month, remove the tires or raise the vehicle to reduce the weight from the tires.

Buying New Tires GM has developed and matched specific tires for the vehicle. The original equipment tires installed were designed to meet General Motors Tire Performance Criteria Specification (TPC Spec) system rating. When replacement tires are needed, GM strongly recommends buying tires with the same TPC Spec rating.

Vehicle Care

10-65

GM's exclusive TPC Spec system considers over a dozen critical specifications that impact the overall performance of the vehicle, including brake system performance, ride and handling, traction control, and tire pressure monitoring performance. GM's TPC Spec number is molded onto the tire's sidewall near the tire size. If the tires have an all-season tread design, the TPC Spec number will be followed by MS for mud and snow. See Tire Sidewall Labeling on page 10‑50. GM recommends replacing worn tires in complete sets of four. Uniform tread depth on all tires will help to maintain the performance of the vehicle. Braking and handling performance may be adversely affected if all the tires are not replaced at the same time. If proper rotation and

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (66,1)

10-66

Vehicle Care

maintenance have been done, all four tires should wear out at about the same time. See Tire Rotation on page 10‑63 for information on proper tire rotation. However, if it is necessary to replace only one axle set of worn tires, place the new tires on the rear axle. Winter tires with the same speed rating as the original equipment tires may not be available for H, V, W, Y and ZR speed rated tires. Never exceed the winter tire's maximum speed capability when using winter tires with a lower speed rating.

{ WARNING

Tires could explode during improper service. Attempting to mount or dismount a tire could cause injury or death.

(Continued)

WARNING (CONTINUED)

WARNING (CONTINUED)

Only your dealer or authorized tire service center should mount or dismount the tires.

A tire and/or wheel could fail suddenly and cause a crash. Use only radial-ply tires with the wheels on the vehicle.

{ WARNING

Mixing tires of different sizes, brands, or types may cause loss of control of the vehicle, resulting in a crash or other vehicle damage. Use the correct size, brand, and type of tires on all wheels.

{ WARNING

Using bias-ply tires on the vehicle may cause the wheel rim flanges to develop cracks after many miles of driving.

(Continued)

If the vehicle tires must be replaced with a tire that does not have a TPC Spec number, make sure they are the same size, load range, speed rating, and construction (radial) as the original tires. Vehicles that have a tire pressure monitoring system could give an inaccurate low-pressure warning if non-TPC Spec rated tires are installed. See Tire Pressure Monitor System on page 10‑58.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (67,1)

The Tire and Loading Information label indicates the original equipment tires on the vehicle. See Vehicle Load Limits on page 9‑12.

Different Size Tires and Wheels If wheels or tires are installed that are a different size than the original equipment wheels and tires, vehicle performance, including its braking, ride and handling characteristics, stability, and resistance to rollover may be affected. If the vehicle has electronic systems such as antilock brakes, rollover airbags, traction control, and electronic stability control, the performance of these systems can also be affected.

{ WARNING

If different sized wheels are used, there may not be an acceptable level of performance and safety if tires not recommended for those wheels are selected. This increases the chance of a crash and serious injury. Only use GM specific wheel and tire systems developed for the vehicle, and have them properly installed by a GM certified technician.

See Buying New Tires on page 10‑65 and Accessories and Modifications on page 10‑3.

Vehicle Care

10-67

Uniform Tire Quality Grading Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example:

Treadwear 200 Traction AA Temperature A The following information relates to the system developed by the United States National Highway Traffic Safety Administration (NHTSA), which grades tires by treadwear, traction, and temperature performance. This applies only to vehicles sold in the United States. The grades are molded on the sidewalls of most passenger car tires. The Uniform Tire Quality Grading (UTQG) system does not apply to deep tread, winter tires, compact spare tires, tires with

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (68,1)

10-68

Vehicle Care

nominal rim diameters of 10 to 12 inches (25 to 30 cm), or to some limited-production tires. While the tires available on General Motors passenger cars and light trucks may vary with respect to these grades, they must also conform to federal safety requirements and additional General Motors Tire Performance Criteria (TPC) standards. All Passenger Car Tires Must Conform to Federal Safety Requirements In Addition To These Grades.

Treadwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire

graded 150 would wear one and one-half (1½) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

Traction – AA, A, B, C The traction grades, from highest to lowest, are AA, A, B, and C. Those grades represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on

straight-ahead braking traction tests, and does not include acceleration, cornering, hydroplaning, or peak traction characteristics.

Temperature – A, B, C The temperature grades are A (the highest), B, and C, representing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passenger car tires must meet under the Federal Motor Safety Standard No. 109. Grades B and A represent higher levels of

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (69,1)

performance on the laboratory test wheel than the minimum required by law. Warning: The temperature grade for this tire is established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either separately or in combination, can cause heat buildup and possible tire failure.

Wheel Alignment and Tire Balance The tires and wheels were aligned and balanced at the factory to provide the longest tire life and best overall performance. Adjustments to wheel alignment and tire balancing will not be necessary on a regular basis. However, check the alignment if there is unusual tire wear or if the vehicle is pulling to one side or the other. If the vehicle vibrates when driving on a smooth

road, the tires and wheels might need to be rebalanced. See your dealer for proper diagnosis.

Wheel Replacement Replace any wheel that is bent, cracked, or badly rusted or corroded. If wheel nuts keep coming loose, the wheel, wheel bolts, and wheel nuts should be replaced. If the wheel leaks air, replace it. Some aluminum wheels can be repaired. See your dealer if any of these conditions exist. Your dealer will know the kind of wheel that is needed. Each new wheel should have the same load-carrying capacity, diameter, width, offset, and be mounted the same way as the one it replaces. Replace wheels, wheel bolts, wheel nuts, or Tire Pressure Monitor System (TPMS) sensors with new GM original equipment parts.

Vehicle Care

10-69

{ WARNING

Using the wrong replacement wheels, wheel bolts, or wheel nuts can be dangerous. It could affect the braking and handling of the vehicle. Tires can lose air, and cause loss of control, causing a crash. Always use the correct wheel, wheel bolts, and wheel nuts for replacement.

Notice: The wrong wheel can also cause problems with bearing life, brake cooling, speedometer or odometer calibration, headlamp aim, rear differential, bumper height, vehicle ground clearance, and tire or tire chain clearance to the body and chassis. See If a Tire Goes Flat on page 10‑70 for more information.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (70,1)

10-70

Vehicle Care

Used Replacement Wheels

{ WARNING

Replacing a wheel with a used one is dangerous. How it has been used or how far it has been driven may be unknown. It could fail suddenly and cause a crash. When replacing wheels, use a new GM original equipment wheel.

Tire Chains

{ WARNING

Do not use tire chains. There is not enough clearance. Tire chains used on a vehicle without the proper amount of clearance can cause damage to the brakes, suspension, or other vehicle parts. The area damaged by the tire chains could cause loss of

(Continued)

WARNING (CONTINUED)

control and a crash. Use another type of traction device only if its manufacturer recommends it for the vehicle's tire size combination and road conditions. Follow that manufacturer's instructions. To avoid vehicle damage, drive slowly and readjust or remove the traction device if it contacts the vehicle. Do not spin the wheels. If traction devices are used, install them on the rear tires.

If a Tire Goes Flat It is unusual for a tire to blow out while driving, especially if the tires are maintained properly. See Tires on page 10‑49. If air goes out of a tire, it is much more likely to leak out slowly. But if there is ever a blowout, here are a few tips about what to expect and what to do: If a front tire fails, the flat tire creates a drag that pulls the vehicle toward that side. Take your foot off the accelerator pedal and grip the steering wheel firmly. Steer to maintain lane position, and then gently brake to a stop, well off the road, if possible. A rear blowout, particularly on a curve, acts much like a skid and may require the same correction as used in a skid. Stop pressing the accelerator pedal and steer to straighten the vehicle. It may be very bumpy and noisy. Gently brake to a stop, well off the road, if possible.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (71,1)

WARNING (CONTINUED)

changing a flat tire. If it is used for anything else, you or others could be badly injured or killed if the vehicle slips off the jack. If a jack is provided with the vehicle, only use it for changing a flat tire.

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place, well off the road, if possible. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑4.

{ WARNING

Driving on a flat tire will cause permanent damage to the tire. Re-inflating a tire after it has been driven on while severely underinflated or flat may cause a blowout and a serious crash. Never attempt to re-inflate a tire that has been driven on while severely underinflated or flat. Have your dealer or an authorized tire service center repair or replace the flat tire as soon as possible.

{ WARNING

Lifting a vehicle and getting under it to do maintenance or repairs is dangerous without the appropriate safety equipment and training. If a jack is provided with the vehicle, it is designed only for (Continued)

Vehicle Care

10-71

{ WARNING

Changing a tire can be dangerous. The vehicle can slip off the jack and roll over or fall causing injury or death. Find a level place to change the tire. To help prevent the vehicle from moving:

1. Set the parking brake firmly. 2. Put an automatic

transmission in P (Park) or a manual transmission in 1 (First) or R (Reverse).

3. Turn off the engine and do not restart while the vehicle is raised.

4. Do not allow passengers to

remain in the vehicle.

5. Place wheel blocks on both

sides of the tire at the opposite corner of the tire being changed.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (72,1)

10-72

Vehicle Care

This vehicle may come with a jack and spare tire or a tire sealant and compressor kit. To use the jacking equipment to change a spare tire safely, follow the instructions below. Then see Tire Changing on page 10‑79. To use the tire sealant and compressor kit, see Tire Sealant and Compressor Kit on page 10‑72. When the vehicle has a flat tire (2), use the following example as a guide to assist you in the placement of wheel blocks (1).

1. Wheel Block 2. Flat Tire

The following information explains how to repair or change a tire.

{ WARNING

Tire Sealant and Compressor Kit

{ WARNING

Idling a vehicle in an enclosed area with poor ventilation is dangerous. Engine exhaust may enter the vehicle. Engine exhaust contains carbon monoxide (CO) which cannot be seen or smelled. It can cause unconsciousness and even death. Never run the engine in an enclosed area that has no fresh air ventilation. For more information, see Engine Exhaust on page 9‑25.

Overinflating a tire could cause the tire to rupture and you or others could be injured. Be sure to read and follow the tire sealant and compressor kit instructions and inflate the tire to its recommended pressure. Do not exceed the recommended pressure.

{ WARNING Storing the tire sealant and compressor kit or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store the tire sealant and compressor kit in its original location.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (73,1)

Tire sealant may not completely seal a 305/35ZR20 tire below –18° C (0° F). If this vehicle has a tire sealant and compressor kit, there may not be a spare tire, tire changing equipment, and on some vehicles there may not be a place to store a tire. The tire sealant and compressor can be used to temporarily seal punctures up to 6 mm (0.25 in) in the tread area of the tire. It can also be used to inflate an under inflated tire. If the tire has been separated from the wheel, has damaged sidewalls, or has a large puncture, the tire is too severely damaged for the tire sealant and compressor kit to be effective. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. Read and follow all of the tire sealant and compressor kit instructions.

The kit includes:

1. On/Off Button 2. Selector Switch (Sealant/Air or

Air Only)

3. Pressure Relief Button 4. Pressure Gauge 5. Air Only Hose (Black) 6. Sealant/Air Hose (Clear) 7. Power Plug

Vehicle Care

10-73

Tire Sealant Read and follow the safe handling instructions on the label adhered to the compressor. Check the tire sealant expiration date on the sealant canister. The sealant canister should be replaced before its expiration date. Replacement sealant canisters are available at your local dealer. See “Removal and Installation of the Sealant Canister” following. There is only enough sealant to seal one tire. After usage, the sealant canister and sealant/air hose assembly must be replaced. See “Removal and Installation of the Sealant Canister” following. Using the Tire Sealant and Compressor Kit to Temporarily Seal and Inflate a Punctured Tire Follow the directions closely for correct sealant usage.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (74,1)

10-74

Vehicle Care

Do not remove any objects that have penetrated the tire. 1. Remove the tire sealant and

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑79.

2. Unwrap the sealant/air hose (6)

and the power plug (7).

3. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the valve stem cap from

the flat tire by turning it counterclockwise.

5. Attach the sealant/air hose (6) onto the tire valve stem. Turn it clockwise until it is tight.

6. Plug the power plug (7) into the

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑5. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

8. Turn the selector switch (2)

clockwise to the Sealant + Air position.

When using the tire sealant and compressor kit during cold temperatures, warm the kit in a heated environment for five minutes. This will help to inflate the tire faster. If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑4. See If a Tire Goes Flat on page 10‑70 for other important safety warnings.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (75,1)

reading. The compressor may be turned on/off until the correct pressure is reached.

Notice: If the recommended pressure cannot be reached after approximately 25 minutes, the vehicle should not be driven farther. The tire is too severely damaged and the tire sealant and compressor kit cannot inflate the tire. Remove the power plug from the accessory power outlet and unscrew the inflating hose from the tire valve. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11.

9. Press the on/off button (1) to

turn the tire sealant and compressor kit on. The compressor will inject sealant and air into the tire. The pressure gauge (4) will initially show a high pressure while the compressor pushes the sealant into the tire. Once the sealant is completely dispersed into the tire, the pressure will quickly drop and start to rise again as the tire inflates with air only.

Inflate the tire to the recommended inflation pressure using the pressure gauge (4). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑56. The pressure gauge (4) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate pressure

10.

Vehicle Care

10-75

11. Press the on/off button (1) to

turn the tire sealant and compressor kit off. The tire is not sealed and will continue to leak air until the vehicle is driven and the sealant is distributed in the tire; therefore, Steps 12–18 must be done immediately after Step 11. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (7) from

the accessory power outlet in the vehicle.

13. Turn the sealant/air hose (6)

counterclockwise to remove it from the tire valve stem.

14. Replace the tire valve

stem cap.

15. Return the sealant/air hose (6) and the power plug (7) back in their original locations.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (76,1)

10-76

Vehicle Care

16.

If the flat tire was able to inflate to the recommended inflation pressure, remove the maximum speed label from the sealant canister and place it in a highly visible location. Do not exceed the speed on this label until the damaged tire is repaired or replaced.

17. Return the equipment to its

18.

original storage location in the vehicle. Immediately drive the vehicle 8 km (5 mi) to distribute the sealant in the tire.

19. Stop at a safe location and

check the tire pressure. Refer to Steps 1–11 under “Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured).” If the tire pressure has fallen more than 68 kPa (10 psi) below the recommended inflation pressure, stop driving the vehicle. The tire is too severely damaged and the tire sealant cannot seal the tire. See Roadside Assistance Program (Mexico) on page 13‑7 or Roadside Assistance Program (U.S. and Canada) on page 13‑11. If the tire pressure has not dropped more than 68 kPa (10 psi) from the recommended inflation pressure, use the compressor kit to inflate the tire to the recommended inflation pressure.

20. Wipe off any sealant from the

wheel, tire, and vehicle.

21. Dispose of the used sealant canister and sealant/air hose (6) assembly at a local dealer or in accordance with local state codes and practices.

22. Replace it with a new canister

available from your dealer.

23. After temporarily sealing a tire

using the tire sealant and compressor kit, take the vehicle to an authorized dealer within 161 km (100 mi) of driving to have the tire repaired or replaced.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (77,1)

1. Remove the tire sealant and

6. Plug the power plug (7) into the

Vehicle Care

10-77

compressor kit from its storage location. See Storing the Tire Sealant and Compressor Kit on page 10‑79.

2. Unwrap the air only hose (5) and

the power plug (7).

3. Place the kit on the ground.

Make sure the tire valve stem is positioned close to the ground so the hose will reach it.

4. Remove the tire valve stem cap

from the flat tire by turning it counterclockwise.

5. Attach the air only hose (5) onto

the tire valve stem by turning it clockwise until it is tight.

accessory power outlet in the vehicle. Unplug all items from other accessory power outlets. See Power Outlets on page 5‑5. If the vehicle has an accessory power outlet, do not use the cigarette lighter. If the vehicle only has a cigarette lighter, use the cigarette lighter. Do not pinch the power plug cord in the door or window.

7. Start the vehicle. The vehicle

must be running while using the air compressor.

8. Turn the selector switch (2)

counterclockwise to the Air Only position.

9. Press the on/off button (1) to

turn the compressor on. The compressor will inflate the tire with air only.

Using the Tire Sealant and Compressor Kit without Sealant to Inflate a Tire (Not Punctured) To use the air compressor to inflate a tire with air only and not sealant:

If a tire goes flat, avoid further tire and wheel damage by driving slowly to a level place. Turn on the hazard warning flashers. See Hazard Warning Flashers on page 6‑4. See If a Tire Goes Flat on page 10‑70 for other important safety warnings.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (78,1)

10-78

Vehicle Care

10.

Inflate the tire to the recommended inflation pressure using the pressure gauge (4). The recommended inflation pressure can be found on the Tire and Loading Information label. See Tire Pressure on page 10‑56. The pressure gauge (4) may read higher than the actual tire pressure while the compressor is on. Turn the compressor off to get an accurate reading. The compressor may be turned on/ off until the correct pressure is reached. If the tire is inflated higher than the recommended pressure, press the pressure relief button (3), if equipped, until the proper pressure reading is reached. This option is only functional when using the air only hose (5).

11. Press the on/off button (1) to

turn the tire sealant and compressor kit off. Be careful while handling the tire sealant and compressor kit as it could be warm after usage.

12. Unplug the power plug (7) from

the accessory power outlet in the vehicle.

13. Disconnect the air only

hose (5) from the tire valve stem, by turning it counterclockwise, and replace the tire valve stem cap.

14. Return the air only hose (5)

and the power plug (7) back to their original locations.

15. Return the equipment to its

original storage location in the vehicle.

Removal and Installation of the Sealant Canister To remove the sealant canister:

1. Remove the plastic cover. 2. Unscrew the connector (2) from

the canister (1).

3. Pull up on the canister (1) to

remove it.

4. Replace with a new canister which is available from your dealer.

5. Push the new canister into

place.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (79,1)

6. Screw the connector (2) to the

3. Turn the center retainer

Vehicle Care

10-79

counterclockwise to remove the cover.

4. Remove the tire sealant and compressor kit from the foam container.

To store the tire sealant and compressor kit, reverse the steps.

Tire Changing

Removing the Spare Tire and Tools

Spare Tire 1. Open the trunk. See Trunk on

page 2‑8.

2. Remove the carpet.

canister (1).

7. Slide the plastic cover back on.

Storing the Tire Sealant and Compressor Kit

The tire sealant and compressor kit is in a foam container in the trunk. 1. Open the trunk. See Trunk on

page 2‑8.

2. Remove the carpet.

3. Turn the center retainer

counterclockwise to remove the spare tire cover.

4. Remove the spare tire and place it next to the tire being changed.

Tools The jack and tools are stored below the spare tire.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (80,1)

10-80

Vehicle Care

Coin/Pierce Jack with Two-Piece

Hex-Head Jack with Three-Piece

Wrench

1. Tool Container 2. Two-Piece Wrench 3. Strap 4. Jack Handle Extension 5. Coin/Pierce Jack

Wrench

1. Tool Container 2. Three-Piece Wrench 3. Strap 4. Hex Head Jack

1. Tool Container 2. Jack 3. End of the Jack 1. Turn the end of the jack (3)

counterclockwise to loosen it. Remove the jack (2) from the retaining bracket.

2. Remove the tool container (1). 3. Remove the tools and tire strap

from the tool container.

4. Place the tools next to the tire

being changed.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (81,1)

Removing the Flat Tire and Installing the Spare Tire 1. Do a safety check before

proceeding. See If a Tire Goes Flat on page 10‑70 for more information. If the vehicle has wheel bolt caps, remove the caps. Store the caps with the wheel cover.

2.

Notice: Make sure that the jack lift head is in the correct position or you may damage your vehicle. The repairs would not be covered by your warranty.

4. Position the jack lift head at the jack location nearest the flat tire. The location is indicated by a mark on the bottom edge of the vehicle. The jack must not be used in any other position. Raise the jack until it engages with the jacking point.

3. Use the fully extended wheel

wrench to loosen all the wheel nuts one-half turn counterclockwise. Do not remove them yet.

Vehicle Care

10-81

{ WARNING

Getting under a vehicle when it is lifted on a jack is dangerous. If the vehicle slips off the jack, you could be badly injured or killed. Never get under a vehicle when it is supported only by a jack.

{ WARNING

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (82,1)

10-82

Vehicle Care

{ WARNING

Raising the vehicle with the jack improperly positioned can damage the vehicle and even make the vehicle fall. To help avoid personal injury and vehicle damage, be sure to fit the jack lift head into the proper location before raising the vehicle.

5.

If you have a coin/pierce jack, attach the jack handle extension to the jack by sliding the hook through the end of the jack and insert the other end of the jack handle into the wrench. If you have a hex head jack, place the hex tube end of the wrench over the hex head of the jack.

6. Raise the vehicle by turning the

wrench clockwise until the vehicle is far enough off the ground to allow enough room for the compact spare tire to fit under the vehicle. Keep the hook parallel to the ground. The wrench may need to be removed and repositioned to continue turning it.

Coin/Pierce Jack and Wrench

Hex Head Jack and Wrench

7. Remove all of the wheel nuts and place them in a dry, clean place to avoid getting dirt in the threads.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (83,1)

Vehicle Care

10-83

10. Reinstall the wheel nuts with the rounded end of the nuts toward the wheel. Tighten each nut as much as possible using the wheel wrench until the wheel is held firmly against the hub. Use your free hand to prevent the wheel from turning while you are tightening.

11. Lower the vehicle by turning

the wrench counterclockwise. Lower the jack completely.

{ WARNING

Rust or dirt on a wheel, or on the parts to which it is fastened, can make wheel nuts become loose after time. The wheel could come off and cause an accident. When changing a wheel, remove any rust or dirt from places where the wheel attaches to the vehicle. In an emergency, a cloth or a paper towel can be used; however, use a scraper or wire brush later to remove all rust or dirt.

8. Remove any rust or dirt from the wheel bolts, mounting surfaces, and spare wheel.

9. Place the compact spare tire on

the wheel-mounting surface.

{ WARNING

Never use oil or grease on bolts or nuts because the nuts might come loose. The vehicle's wheel could fall off, causing a crash.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (84,1)

10-84

Vehicle Care

12. Tighten the wheel nuts firmly in

a crisscross sequence, as shown.

{ WARNING

Wheel nuts that are improperly or incorrectly tightened can cause the wheels to become loose or come off. The wheel nuts should be tightened with a torque wrench to the proper torque specification after replacing. Follow the torque specification supplied by the aftermarket manufacturer when using accessory locking wheel nuts. See Capacities and Specifications on page 12‑2 for original equipment wheel nut torque specifications.

Notice: Improperly tightened wheel nuts can lead to brake pulsation and rotor damage. To avoid expensive brake repairs, evenly tighten the wheel nuts in the proper sequence and to the

proper torque specification. See Capacities and Specifications on page 12‑2 for the wheel nut torque specification. Storing a Flat or Spare Tire and Tools

{ WARNING

Storing a jack, a tire, or other equipment in the passenger compartment of the vehicle could cause injury. In a sudden stop or collision, loose equipment could strike someone. Store all these in the proper place.

To store a flat or spare tire and tools: 1. Return the jack and tools as they

were originally stored in the trunk.

2. Return the spare tire cover as it

3.

was in the trunk. Install the retainer nut and turn it clockwise until tight.

4. Return the rear trunk carpet. 5. Place the flat tire face up on the

load floor.

6. Route the strap provided, as shown, to secure the flat tire.

The compact spare tire is for temporary use only. Replace the compact spare with a full-size tire as soon as possible.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (85,1)

Compact Spare Tire { WARNING Driving with more than one compact spare tire at a time could result in loss of braking and handling. This could lead to a crash and you or others could be injured. Use only one compact spare tire at a time.

If this vehicle has a compact spare tire, it was fully inflated when new; however, it can lose air over time. Check the inflation pressure regularly. It should be 420 kPa (60 psi). Stop as soon as possible and check that the spare tire is correctly inflated after being installed on the vehicle. The compact spare tire is designed for temporary use only. The vehicle will perform differently with the spare tire installed and it is recommended that the vehicle speed be limited to 80 km/h

(50 mph). To conserve the tread of the spare tire, have the standard tire repaired or replaced as soon as convenient and return the spare tire to the storage area. Notice: When the compact spare is installed, do not take the vehicle through an automatic car wash with guide rails. The compact spare can get caught on the rails which can damage the tire, wheel, and other parts of the vehicle. Do not use the compact spare on other vehicles. Do not mix the compact spare tire or wheel with other wheels or tires. They will not fit. Keep the spare tire and its wheel together. Notice: Tire chains will not fit the compact spare. Using them can damage the vehicle and the chains. Do not use tire chains on the compact spare.

Vehicle Care

10-85

Jump Starting For more information about the vehicle battery, see Battery on page 10‑32. If the battery has run down, try to use another vehicle and some jumper cables to start your vehicle. Be sure to use the following steps to do it safely.

{ WARNING

Batteries can hurt you. They can be dangerous because:

. They contain acid that can

burn you.

. They contain gas that can

explode or ignite.

. They contain enough electricity to burn you.

If you do not follow these steps exactly, some or all of these things can hurt you.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (86,1)

10-86

Vehicle Care

Notice: Ignoring these steps could result in costly damage to the vehicle that would not be covered by the warranty. Trying to start the vehicle by pushing or pulling it will not work, and it could damage the vehicle.

1. Remote Positve (+) Terminal 2. Remote Negative (-) Terminal The jump start remote positive (1) and negative (2) terminals are in the engine compartment on the driver side of the vehicle.

These terminals are used instead of a direct connection to the battery. The positive jump start connection is covered by a red cap. Remove to expose the terminal. 1. Check the other vehicle. It must

have a 12-volt battery with a negative ground system.

Notice: Only use a vehicle that has a 12-volt system with a negative ground for jump starting. If the other vehicle does not have a 12-volt system with a negative ground, both vehicles can be damaged. 2. Position the two vehicles so that

they are not touching.

3. Set the parking brake firmly.

Vehicles with an automatic transmission should be in P (Park). See Shifting Into Park on page 9‑21. Vehicles with a manual transmission should be in Neutral. See Parking (Manual Transmission) on page 9‑24.

Notice: If any accessories are left on or plugged in during the jump starting procedure, they could be damaged. The repairs would not be covered by the vehicle warranty. Whenever possible, turn off or unplug all accessories on either vehicle when jump starting the vehicle. 4. Turn the ignition to LOCK/OFF

and switch off all lights and accessories in both vehicles, except the hazard warning flashers if needed.

{ WARNING

An electric fan can start up even when the engine is not running and can injure you. Keep hands, clothing and tools away from any underhood electric fan.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (87,1)

Vehicle Care

10-87

10. Try to start the vehicle that had

the dead battery. If it will not start after a few tries, it probably needs service.

Notice: If the jumper cables are connected or removed in the wrong order, electrical shorting may occur and damage the vehicle. The repairs would not be covered by the vehicle warranty. Always connect and remove the jumper cables in the correct order, making sure that the cables do not touch each other or other metal.

Jumper Cable Removal Reverse the sequence exactly when removing the jumper cables.

{ WARNING

{ WARNING

Using a match near a battery can cause battery gas to explode. People have been hurt doing this, and some have been blinded. Use a flashlight if you need more light. Be sure the battery has enough water. You do not need to add water to the battery installed in your new vehicle. But if a battery has filler caps, be sure the right amount of fluid is there. If it is low, add water to take care of that first. If you do not, explosive gas could be present. Battery fluid contains acid that can burn you. Do not get it on you. If you accidentally get it in your eyes or on your skin, flush the place with water and get medical help immediately.

Fans or other moving engine parts can injure you badly. Keep your hands away from moving parts once the engine is running.

5. Connect one end of the red

positive (+) cable to the jump start positive (+) post.

6. Connect the other end of the red

positive (+) cable to the positive (+) terminal of the good battery.

7. Connect one end of the black

negative (–) cable to the negative (–) terminal of the good battery.

8. Connect the other end of the

black negative (–) cable to the negative (–) post.

9. Start the engine in the vehicle with the good battery and run the engine at idle speed for at least four minutes.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (88,1)

The vehicle was neither designed nor intended to be towed with any of its wheels on the ground. If the vehicle must be towed, see “Towing the Vehicle” earlier in this section.

10-88

Vehicle Care

Towing

Towing the Vehicle Notice: Incorrectly towing a disabled vehicle may cause damage. The damage would not be covered by the vehicle warranty. Have the vehicle towed on a flatbed car carrier. A wheel lift tow truck could damage the vehicle.

Due to low ramp angles on the ZL1, use care when loading the vehicle onto a flatbed carrier. Front spring spacers are provided for lifting the front suspension. Consult your dealer or a professional towing service if the disabled vehicle must be towed. To tow the vehicle behind another vehicle for recreational purposes, such as behind a motor home, see “Recreational Vehicle Towing” in this section.

Recreational Vehicle Towing Notice: Dolly towing or dinghy towing the vehicle may cause damage because of reduced ground clearance. Always put the vehicle on a flatbed truck or trailer.

Chevrolet Camaro Owner Manual - 2013 - CRC - 4/18/12

Black plate (89,1)

Appearance Care

Exterior Care

Washing the Vehicle To preserve the vehicle's finish, wash it often and out of direct sunlight. Notice: Do not use petroleum-based, acidic, or abrasive cleaning agents as they can damage the vehicle's paint, metal, or plastic parts. If damage occurs, it would not be covered by the vehicle's warranty. Approved cleaning products can be obtained from your dealer. Follow all manufacturer directions regarding correct product usage, necessary safety precautions, and appropriate disposal of any vehicle care product. Notice: Avoid using high-pressure washes closer than 30 cm (12 in) to the surface of the vehicle. Use of power washers

exceeding 8,274 kPa (1,200 psi) can result in damage or removal of paint and decals. Rinse the vehicle well, before washing and after, to remove all cleaning agents completely. If they are allowed to dry on the surface, they could stain. Dry the finish with a soft, clean