Press the left side tune button to tune to lower frequencies and the right side to tune to higher frequencies. The tuned frequency is displayed.
ST will be displayed to indicate stereo FM reception.
pg. 137 Radio SC-813
A - Seek tuning up/down
Press the left side tune button to tune to lower frequencies and the right side to tune to higher frequencies. The radio seeks the next audible station and stops there. If you wish to continue the seek tuning, press the tune button again. B - Preset programming
1. Tune to the desired frequency.
2. Depress and hold a preset button. The audio will cut out. Keep the button depressed until the audio comes on again (approx. 2 seconds).
3. The frequency is now stored on this preset button. C - Preset buttons
To select a pre-programed radio frequency, depress the preset button. The set frequency will be displayed.
pg. 138 Radio SC-813
A - Automatic programming (Auto)
Please note that this function will not interfere with pre-stored stations on buttons 1-6.
This function automatically seeks and stores up to 8 strong AM or FM stations.
This is especially useful when travelling in areas where radio stations are unfamiliar.
1. Depress and hold the "AUTO" button for at least 1 second. A number of strong stations (max. 8) on the chosen waveband are now automatically stored in the memory.
If there are no audible stations, "- - - -" is displayed.
2. Press the "AUTO" button (for less than 1 second) to obtain another autostored station. A new station will be selected each time the button is pressed momentarily. B - Bass control
Adjust the bass by sliding the control up or down (up to increase, down to decrease).
A "detent" indicates "equalized" bass. C - Treble control
Adjust the treble by sliding the control up or down (up to increase, down to decrease).
A "detent" indicates "equalized" treble.
pg. 139 Radio SC-813
A - Fader control
Adjust front/rear speaker balance by sliding the control up or down (up to direct more sound to the front speakers, down to direct more sound to the rear speakers).
The "detent" indicates "equalized" front/rear balance position. B - Pause function
Press the "volume" knob to temporarily mute the sound. "PAUSE" is displayed. C - Balance control
Pull out the "volume" knob and adjust the left/right balance by turning the knob counter-clockwise or clockwise. D - Scan
Press this button to listen to each station for five seconds. Press it again to stop scanning. "Scan" will be displayed during scanning. E - Active sound control (ASC)
The ASC function automatically adjusts the volume level of the audio system according to driving speed. To deactivate ASC depress the "ASC" button. To activate ASC, depress the "ASC" button until "ASC" is displayed.
pg. 140 Cassette deck
A - Cassette slot
The cassette is inserted with the open side to the right (side 1 or A of the cassette upwards).
When the cassette is inserted, the radio is disengaged and the cassette will start to play automatically. "TAPE > " or "TAPE < " is displayed to indicate which side of the tape is being played. When one side of the tape has been played the unit will automatically play the other side (auto-reverse). The cassette can be inserted or ejected even when the unit is switched off. B - Reversing the tape (PROG)
Press the button to play the other side of the tape.
The side of the tape being played will be displayed. C - Fast winding
The tape is advanced with "
" and rewound with "
".
Fast winding can be stopped by pressing either the selected button or the fast wind button again or by pressing the "TAPE" button. D - Dolby B NR button
Press this button when you use tapes recorded with the Dolby B noise reduction system.
The Dolby symbol
will be indicated in the display.
pg. 141 Cassette deck
A - Next selector
Press the "
" button and the tape will automatically advance to the next song.
There must be a gap (no audio sound) of approx. 5 seconds between songs for this function to operate. B - Previous selector
Press the "
" button and the tape will automatically rewind to the previous song.
There must be a gap (no audio sound) of approx. 5 seconds between songs for this function to operate. C - Pause
If you press the "volume" knob the tape is stopped, the unit is silent and "PAUSE" is displayed. To restart the tape press the knob again. D - Scan
Press this button to listen to the first five seconds of each song. Press this button or the "TAPE" button to stop scanning. During scanning "SCAN" will be displayed. There must be a gap (no audio sound) of approx. 5 seconds between songs for this function to operate.
Contents | Top of Page
2 0 0 3 VOLVO
C70
INDEX
pg. 190 HomeLink® Universal Transceiver (option)
HomeLink® Universal Transceiver
HomeLink® is an advanced system that can be programmed to learn the codes of three different remote controlled- devices (e.g., garage door openers, remote lighting, entry door lock). HomeLink®'s sun visor-mounted transceiver, powered by your car's electrical system, may then be used in place of your hand-held remote controls.
NOTE: For your security, the HomeLink® Universal Transceiver is designed to not function if you lock your car from the outside.
Programming the transceiver
1. The ignition switch must be turned to the "accessory" position (II) before programming the HomeLink® Universal Transceiver.
2. Begin by erasing all 3 factory default channels. Hold down the two outside buttons (buttons 1 and 3 in the illustration) on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink® 's indicator light begins to flash. Then release the buttons.
3. Hold your hand-held transmitter (garage door opener, for example) 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface, keeping the indicator light in view. For placement questions, contact HomeLink® toll-free 1- 800-355-3515 (Internet: www.HomeLink.com).
4. Using two hands, push and hold both your hand-held transmitter's button and the transceiver button you wish to program. The indicator light will flash first slowly, then rapidly. Rapid flashing tells you the HomeLink® button has been successfully programmed. Release both buttons.
5. If you are programming a rolling code-equipped device (e.g., garage door opener or entry door lock), refer to "Programming rolling codes" on the next page to complete the programming process.
Repeat steps 3 and 4 to program the other two transceiver buttons.
If, after several attempts, you are unable to successfully train the HomeLink® Universal Transceiver to learn your hand-held transmitter's signal, contact HomeLink® toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
WARNING!
If you use HomeLink® to open a garage door or gate, be sure no one is near the gate or door while it is in motion. Do not use the HomeLink® Universal Transceiver with any garage door opener that lacks safety "stop" and
"reverse" features as required by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982) A garage door opener that cannot "detect" an object, signalling the door to "stop" and "reverse" does not meet current federal safety standards. Using a garage door opener without these features increases the risk of serious injury or death. For more information on this matter, call toll-free 1-800-355- 3515 (Internet: www.HomeLink.com).
pg. 191 HomeLink® Universal Transceiver (option)
NOTE - Canadian residents:
During programming, your hand-held transmitter may automatically stop transmitting. To successfully train HomeLink® , continue to hold the HomeLink® button. At the same time, repeatedly press and hold your hand-held transmitter's button at two-second intervals until HomeLink® has learned your transmitter's code. The HomeLink® indicator light will flash first slowly, and then rapidly to indicate that the button has been successfully programmed.
Determining if your garage door uses a rolling code
Determining if your garage door uses a rolling code Determine, in one of the following ways, if your garage door uses a rolling code system and is manufactured after 1996:
Refer to the garage door opener owner's manual for verification. If your hand-held transmitter appears to program the HomeLink® Universal Transceiver but the programmed button
does not activate the garage door, your garage door opener may have a rolling code.
Press the programmed HomeLink® button. If the garage door opener has the rolling code feature, the HomeLink®
indicator light flashes rapidly and then glows steadily after approximately 2 seconds.
To train a rolling code garage door opener , follow these instructions after programming the desired transceiver button according to "Programming the transceiver." The help of a second person may make training easier.
1. Locate the training button on the garage door opener motor head unit. The location and color of the training button
may vary. If you encounter difficulty, refer to the garage door opener owner's manual or call toll-free 1-800-355-3515
(Internet: www.HomeLink.com).
2. Press the "training" button on the garage door opener motor head unit until the "training" light comes on.
3. Press and release the programmed HomeLink® button. Press and release the programmed HomeLink® button a second time to complete the training process. Some garage door openers may require you to do this procedure a third time to complete the training.
The programmed button on your HomeLink® Universal Transceiver should now operate your garage door opener. The original hand-held transmitter can also be used, as desired, to operate the garage door.
The remaining two HomeLink® buttons can be programmed in the same way. In the event of any problems in programming the HomeLink® Universal Transceiver, call toll-free 1-800-355-3515 (Internet: www.HomeLink.com).
Operating the HomeLink® Universal Transceiver Once programmed, the HomeLink® Universal Transceiver can be used in place of your hand-held transmitters.
To operate, the key must be turned to the "accessory" position (II) or the engine must be running. Press the programmed HomeLink® button to activate the garage door, driveway gate, security lighting, home security system, etc.
Your original hand-held transmitters may, of course, be used at any time.
Erasing programmed buttons
Individual buttons cannot be erased. To erase all three programmed buttons:
1. Turn the ignition key to the "accessory" position (II).
2. Hold down the two outside buttons on the HomeLink® Universal Transceiver for about 20 seconds, until HomeLink® 's indicator light begins to flash.
3. Release both buttons.
The HomeLink® buttons can be reprogrammed using the procedures described on the previous page.
(HomeLink® information is continued on the next page)
pg. 192 HomeLink® Universal Transceiver (option)
Reprogramming a single HomeLink® button
1. Press and hold the desired HomeLink® button. Do not release the button until step 3 has been completed.
2. When the indicator light begins to flash slowly (after approximately 20 seconds), position the hand-held transmitter 2 to 5 in. (5 to 12 cm) away from the HomeLink® surface.
3. Press and hold the hand-held transmitter button. The HomeLink® indicator light will begin to flash, first slowly then rapidly. When the indicator light flashes rapidly, release both buttons.
The previously programmed device has now been erased and the new device can be activated by pressing the HomeLink® button that has just been programmed. This procedure will not affect any other programmed HomeLink® buttons.
NOTE:
Retain the original transmitter(s) for future programming procedures (i.e., if you purchase a new car). It is also suggested that if you sell your car, the programmed channels on the HomeLink® Universal Transceiver be
erased for security purposes.
Contents | Top of Page
2 0 0 3 VOLVO
C70
INDEX
pg. 193 - 195 Index
ABS
Air conditioning
Air filter- engine
Air mix
Air vents
Airbag (SIPS)
Airbag (SRS)
Alarm
Ambient temperature sensor
Anti-lock Brake System (ABS)
Antifreeze
Ashtrays
Audio systems
-General information
-SC-813
-SC-816
-SC-900/01
Automatic car washing
Automatic daytime running
Automatic transmission
-Kickdown
Automatic transmission fluid
Battery
Battery drain - avoiding
Battery maintenance
Booster cushion
Brake failure warning light
Brake fluid
Brake fluid warning light
Brake system
17
35
113
33
33
45
25
17,74
77
31
186
134
147
163
107
24
66,129
67
126
77,130
57
122
12
17, 18
118,126
18
74, 75
17
17,19
130
129
123
44
81
86
12
12
107
34
16
25
118
65
107
40
102
120
19
17
69,128
20
51
29
Brake warning light
Bulb failure warning
Bulbs
Capacities
Catalytic converter
Central locking system
Chains (snow)
Changing a wheel
Child booster cushion
Child safety
Cleaning the convertible top
Climate control systems
Clock
Clock - resetting
Clutch fluid
Clutch interlock
Convertible top - cleaning
Convertible top - electrically operated
Convertible top - manually raising
Coolant - checking/changing
Coolant level sensor
Coolant level warning light
Cooling system
Courtesy lights - exterior
Courtesy lights - front
Cruise control
Daytime running lights
Demister - rear window
Dimensions
Distributor ignition system
Diversity antenna
Doors and locks
Driving economy
Driving mode W
EBD (Electronic Brake-force Distribution) 75
ECC - Electronic Climate Control
Electrical system
Electrically heated front seats
Electrically operated convertible top
Electrically operated front seats
Electrically operated windows
24
23
131
128
189
43
63
67, 77
34, 35
69,130
30
40
47
36
71, 72
23
127
113
121
116, 117,126
116
17
20
Electronic Brake Distribution (EBD)
75
Electronic Brake-force Distribution (EBD) 75
Emergency towing
Emergency warning flashers
Engine
Engine air filter
Engine compartment
Engine oil
Engine oil - checking/changing
Engine oil pressure
Exterior courtesy lights
Fog light - rear
Fog lights - front
Front courtesy lights
Front fog lights
Front seats
Front seats - heated
Front seats - memory function
Fuel filter
Fuel gauge
Fuel level
Fuel requirements
Fuel system
Fuel tank cover - opening
opening manually
Fuses
Fuses - replacing
Gas tank cover - opening
opening manually
Generator
Hand brake
Handling
Hazard warning flashers
Headlight wiper blades - replacing
Headlights
Heated front seats
Heated side-view mirrors
Heating
Heating and air conditioning
High beams
Hoisting the car
30
68
23
100
20
30
23
35
33
17
112
17,22
22
51
22
47
30
47
113
16
17
60, 61
113, 128
37, 62
101, 102
95, 96, 97
95
37, 62
101, 102
17, 130
Homelink® Hood Ignition switch Immobilizer (start inhibitor) Instrument illumination Instruments Jack Jump starting Keyless entry system Keylock Keys Kick-down Kickdown Label information Lifting the car Locks Long load storage Lubrication Luggage racks - trunk-mounted Lumbar support Maintenance service Malfunction indicator lamp Manual transmission Manually raising convertible top Memory function - front seats Mirrors - rear/side view Occupant safety Octane rating Odometer Oil (engine) Oil pressure warning light Opening the trunk from the inside Paint touchup Parking brake Parking brake reminder light Parking lights PCV system
190-192
54
21
43
22
14, 15
56, 86
73
44
64
43
66
67
110
112
43
53
115
70
49
111
17
65, 129
102
47
50
13
62
16
116, 117, 126
18
55
104
17,30
18
20
113
Polishing
Power seats
Power steering fluid
Radio
-General information
-SC-813
-SC-816
-SC-900/01
Radio Data System - RDS
Rear fog light
Rear suspension
Rear window demister
Rear/side-view mirrors
Refueling
Remote control (central locking system)
Remote keyless entry system
Replacing bulbs
Replacing fuses
Reporting safety defects
Road assistance
Roadholding
Roll Over Protection System (ROPS)
Rotating tires
Safety defects - reporting
Seat belt maintenance
Seat belts
- Automatic Locking Retractor
- Emergency Locking Retractor
Seat belts - cleaning
Seats
Seats - heated
Securing cargo
Service reminder indicator
Servicing
Shift lock
Shiftlock
Shiftlock release (override)
Side Impact Protection System (SIPS)
Side-view mirrors - heated
SIPS
Snow chains
Snow tires
107
47
118, 126
186
134
147
163
168
17, 22
128
23
50
62
44
44
89-94
95
13
132
68
10
82
13
13
2,3,11
11
11
108
47
30
57
17
112, 114
64
66
101
23
81
81
Spare tire Spare tire (sedan) Spark plugs Speakers (rear seat) - turning on/off Specifications SRS SRS diagnostic system SRS warning light Stability and Traction Control (STC) Start inhibitor (immobilizer) Starting the engine Steering wheel adjustment Steering wheel lock Storage compartments Studded tires Tachometer Temperature gauge Temporary spare tire Three-way catalytic converter Timing belt Tire pressure Tire rotation Tires - changing Towing Towing a trailer Towing the car Trailer towing Trip computer Trip odometer Trunk - opening from the inside Trunk - opening/locking Trunk light Turn signals Uniform tire quality grading Upholstery - cleaning Vanity mirrors Vehicle Identification Number (VIN) Vehicle loading Volvo On Call Warning flashers
88
56
113, 128
36
125
5,6,7
19
5,17, 19
19, 23, 75
43
64
32
21
42
81
16
16
88
123
113
82
82
86
71, 72
76
72
76
23, 26, 27, 28
16
55
55
56
17,20
83
108
52
110
129
133
23
Warning lights Warranty Washer fluid level Washer fluid reservoir Washing Waxing Wheel changing Wheels and tires WHIPS Whiplash Protection System(WHIPS) Wind deflector Windshield washer nozzles Windshield washers/wipers Windshield wiper blades - replacing Winter driving Winter/Wet driving mode
18, 19
111
17
119
106
107
86, 87
80
41
119
21
99
77
67, 77
Contents | Top of Page
2 0 0 3 VOLVO
C70
Back Cover
Back Cover
Accessory Installation - Important Warning
We strongly recommend that Volvo owners install only genuine, Volvo-approved accessories, and that accessory
installations be performed only by the factory-trained technicians at your authorized Volvo retailer.
Genuine Volvo accessories are tested to ensure compatibility with the performance, safety, and emission systems in your car. Additionally, your authorized Volvo retailer knows where accessories may and may not be safely installed in your Volvo. In all cases, please consult your authorized Volvo retailer before installing any accessory in or on your car.
Accessories that have not been approved by Volvo may or may not be specifically tested for compatibility with your
car. Additionally, an inexperienced installer may not be familiar with some of your car's systems.
Any of your car's performance and safety systems could be adversely affected if you install accessories that Volvo
has not tested, or if you allow accessories to be installed by someone unfamiliar with your car.
Damage caused by unapproved or improperly installed accessories may not be covered by your new car warranty.
See your Warranty and Service Records Information booklet for more warranty information. Volvo assumes no responsibility for death, injury, or expenses that may result from the installation of non-genuine accessories.
Driver Distraction
Driver distraction results from driver activities that are not directly related to controlling the car in the driving environment. Your new Volvo is, or can be, equipped with many feature-rich entertainment and communication systems. These include hands-free cellular telephones, navigation systems, and multipurpose audio systems. You may also own other portable electronic devices for your own convenience. When used properly and safely, they enrich the driving experience. Improperly used, any of these could cause a distraction.
For all of these systems, we want to provide the following warning that reflects the strong Volvo concern for your
safety:
parked.
Never use these devices or any feature of your vehicle in a way that distracts you from the task of driving safely.
In addition to this general warning, we offer the following guidance regarding specific newer features that may be
Never use a hand-held cellular telephone while driving. Some jurisdictions prohibit cellular telephone use by a
Distraction can lead to a serious accident.
found in your vehicles:
driver while the vehicle is moving.
If your car is equipped with a navigation system, set and make changes to your travel itinerary only with the vehicle
Never program your audio system while the vehicle is moving. Program radio presets with the vehicle parked, and
use your programmed presets to make radio use quicker and simpler.
Never use portable computers or personal digital assistants while the vehicle is moving.
A driver has a responsibility to do everything possible to ensure his or her own safety and the safety of passengers in the vehicle and others sharing the roadway. Avoiding distractions is part of that responsibility.
The following should be checked regularly: *
1 Washer fluid reservoir should be filled with water and solvent (wintertime: windshield washer anti-freeze). See page 119.
2 Coolant level should be between the expansion tank marks. Mixture: 50% anti-freeze and 50% water. See page 120.
3 Power steering - When cold, the level must not be above the COLD mark and when hot it must not be above the HOT mark. Top up if the level drops to the ADD mark with ATF fluid. See page 118.
4 Engine oil level should be between the dipstick marks. The distance between the marks represents approx. 1.6 US qts (1.5 liters). See page 116.
5 Brake fluid - check, without removing the cap, that the level is above the MIN mark. Use brake fluid DOT 4+. See page 118.
* Engine oil should be checked each time the car is refuelled.
Octane rating, see page 60.
Tire pressure, see label located on the rear edge of the right front door.
Bulbs Power Socket US no.
55 W -
30/7 W BA 15s 3357NA
55 W PK 22s H1
5 W BA 15s 67
H7
5
21 W BAU 15 -
21 W BA 15s 1156
See pages 89-94 for more detailed information.
Volvo Car Corporation
Göteborg, Sweden
Contents | Top of Page