(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
CAUTION
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.
100
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13010
LS13011
LS13012
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
the
To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing the infant seat
firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
101
06 09.29
LS13013
LS13014
LS13015
4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.
installing, follow instructions about
installing
for
CAUTION
Rear−facing child restraint system: Never install a rear−facing child re- straint system on the front passenger seat with the passenger airbag off switch in the “AUTO” position. In the event of an accident, the force of the rapid inflation of the front passenger airbag can cause death or serious in- jury to the child if the rear−facing child restraint system is installed on the front passenger seat.
102
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
CAUTION
CAUTION
LS13006a
If you must install a rear−facing child restraint system on the front passen- ger seat, make sure that the passen- ger airbag off switch is in the “OFF” position with the key removed and that the indicator light is on.
When you install a rear−facing child re- straint system which belongs to a pas- senger risk group on the front passen- ger seat, turn the passenger airbag off switch counterclockwise to the “OFF” position and remove the key. (For de- tails, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.) The indicator system is off.
light comes on when the
child
forward−facing
Forward−facing child restraint system: restraint system which belongs to a passenger risk group should never be installed on the front passenger seat with the passenger airbag off switch in the “AUTO” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.)
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
103
06 09.29
LS13016
LS13017
CAUTION
the
lock mechanism of
(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
provided insert the
by tab
CAUTION
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- straint system on the rear right seat.
104
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13018
LS13019
LS13020
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing
the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
105
06 09.29
LS13021
LS13022
4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.
CAUTION
child
forward−facing
restraint system which belongs to a passenger risk group should never be installed on the front passenger seat with the passenger airbag off switch in the “AUTO” position, because the force of the deploying airbag could cause death or serious injury to the child in forward seating position. (For details, see “SRS driver airbag and front passenger airbag” on page 55 in this Section.)
106
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13023
1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.
Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 43 in this Section for details.
CAUTION
(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.
(cid:1) If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
could
(cid:1) Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.
injuries due
(cid:1) For child’s safety, do not place the
shoulder belt under child’s arm.
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
107
06 09.29
—Installation with seat belt (regular cab models with bench seat and double cab models)
LS13024
LS13028
LS13029
2. To remove the booster seat, press the the
buckle release button and allow belt to retract.
(A) INFANT SEAT INSTALLATION An infant seat must be used in rear− facing position only.
CAUTION
classification
(cid:1) Never install a rear−facing child re- straint system on the front passen- ger seat even if the front passenger occupant indicator light indicates “OFF”. In the event of an accident, the impact of the rapid inflation of the front passen- ger airbag could cause death or se- rious injury to the child if the rear− facing child is front passenger installed on seat.
restraint system the
108
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13030
LS13031
the
lock mechanism of
(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
CAUTION
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- the rear right straint system on seat. system installed on the rear seat should not contact the front seatbacks.
restraint
Child
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
109
06 09.29
LS13032
LS13033
LS13034
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
the
To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing the infant seat
firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
110
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13035
LS13036
Install the child restraint system on the right front passenger seat (regular cab models with bench seat) or front passen- ger seat (double cab models) only when it is unavoidable. Your vehicle is equipped with a front passenger occupant classifica- tion system. In order to activate the occu- pant classification system correctly, install the forward−facing child restraint system on the front passenger seat in the follow- ing order: 1. Turn the ignition key to the “ON” posi-
tion.
4. To remove the infant seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(B) CONVERTIBLE SEAT INSTALLATION A convertible seat must be used in for- ward−facing or rear−facing position de- pending on the age and size of the the child. When manufacturer’s the applicable age and size of the child as well as directions the child restraint system.
installing, follow instructions about
installing
for
2. Move
the right
front passenger seat (regular cab models with bench seat) or front passenger seat (double cab models) to the rearward position.
3. Put the child restraint system on the right front passenger seat (regular cab models with bench seat) or front pas- senger seat (double cab models) with- out putting your weight on the right front passenger seat (regular cab mod- els with bench seat) or front passenger seat (double cab models).
4. Insert the seat belt tab into the seat
belt buckle.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
111
06 09.29
5. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the seat securely, make sure the belt is in the lock mode before letting the belt retract.
6. While pressing
the convertible seat the seat cushion and firmly against seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
7. Put a child on the child restraint sys- tem and secure the child, complying with the instructions provided by the child restraint system manufacturer.
indicator
indicates
The front passenger occupant classifica- tion indicator light should indicate “OFF” when the ignition key is in the “ON” posi- tion and the child is in the child restraint system after following these procedures. The “OFF” the SRS front passenger airbag and side airbag on the passenger side will not deploy. if the indicator light indicates “ON”, do the fol- lowing procedure: 1. Turn the ignition off. 2. Remove the child restraint system. 3. When reinstalling a child restraint sys- tem, make sure the seatback does not press into the seat cushion. If this occurs, adjust the seatback angle slightly.
the child restraint system
4. Then make sure the head restraint is not pressing the child restraint system into the seat cushion. If this occurs, raise the head restraint.
5. Turn the ignition on again.
the
ignition key
The front passenger occupant classifica- tion indicator light should indicate “OFF”. If the indicator light still indicates “ON” when to the “ON” position, then the SRS front passen- ger airbag and side airbag on the passen- ger side may deploy in an accident. Do not drive the vehicle in this condition. Re- move the child restraint system and con- tact your Toyota dealer.
turned
is
CAUTION
the
(cid:1) Never install a rear−facing child re- straint system on the front passen- ger seat. A forward−facing child re- straint system should only be installed on front passenger seat when unavoidable. If you must install the child restraint system on the front passenger seat, put the seat in its most rearward position, and install the forward−facing child restraint system in the proper or- der. Otherwise, the front passenger occupant classification system can not detect the presence of the child restraint system and the front pas- senger airbag and side airbag on the front passenger seat could deploy.
112
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13037
LS13038
Move seat fully back
the
(cid:1) A forward−facing child restraint sys- tem should be allowed to be installed on front passenger seat only when it is unavoidable. Always move the seat as far back as possible even if the front pas- senger occupant classification indi- cator light indicates “OFF”, because the front passenger airbag could in- flate with considerable speed and force. Otherwise, the child may be killed or seriously injured.
CAUTION
classification
(cid:1) Never install a rear−facing child re- straint system on the front passen- ger seat even if the front passenger occupant indicator light indicates “OFF”. In the event of an accident, the impact of the rapid inflation of the front passen- ger airbag could cause death or se- rious injury to the child if the rear− facing child is front passenger installed on seat.
restraint system the
(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
113
06 09.29
LS13039
LS13040
the
lock mechanism of
(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.
provided insert the
by tab
CAUTION
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
(cid:1) If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
(cid:1) If the driver’s seat position does not allow sufficient space for safe the child installation, install re- the rear right straint system on seat. system installed on the rear seat should not contact the front seatbacks.
restraint
Child
114
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
LS13041
LS13042
LS13043
2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.
To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.
3. While pressing
the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.
CAUTION
Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
115
06 09.29
LS13044
LS13045
LS13046
4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.
freely again and be ready
(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.
Move seat fully back
CAUTION
the
(cid:1) A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the front pas- senger occupant classification indi- cator light indicates “OFF”, because the front passenger airbag could in- flate with considerable speed and force. Otherwise, the child may be killed or seriously injured.
116
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
(cid:1) On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.
LS13047
1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.
Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on the child’s hips. See “Seat belts” on page 43 in this Section for details.
CAUTION
(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.
could
(cid:1) Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.
injuries due
(cid:1) For child’s safety, do not place the
shoulder belt under child’s arm.
(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.
(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
117
06 09.29
(cid:1) If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.
install
LS13048
LS13050a
—Using a top strap (regular cab models)
2. To remove the booster seat, press the the
buckle release button and allow belt to retract.
Follow the procedure below for a child restraint system that requires the use of a top strap.
118
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
Symbol mark
Routing device
LS13052b
Use the routing device and the anchor bracket on the back panel to attach the top strap. Anchor brackets are installed for (each) passenger seating position. This symbol indicates the locations of the anchor brackets.
LS13063
Anchor brackets
Bench seat
Symbol mark
Routing device
LS13053bAnchor
bracket
Separate seats
TO USE THE ANCHOR BRACKET: 1. Remove
the passenger head
re-
straint.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
119
06 09.29
Symbol mark
LS13181
LS13064b
LS13065b
2. Lightly push down on the top sur- face of the routing device cover with the symbol mark shown in the il- lustration, then pull it forward to re- move.
the
through
top strap
3. Pull the seatback release lever and swing the seatback forward slightly. Route the routing device as shown in the il- lustration. Latch bracket. Return the seatback to upright posi- tion.
the hook onto
the anchor
4. Fix the child restraint system with the seat belt and tighten the top strap. Replace straint.
the passenger head
re-
Store the removed cover in a safe place such as the glove box. Be sure to replace the cover when the anchor bracket is not in use. For instructions on installing the child re- straint system, see “Child restraint” on page 95 in this Section.
120
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
CAUTION
(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback.
is securely
(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.
—Using a top strap (access cab models)
LS13069
Front position
Follow the procedure below for a child restraint system that requires the use of a top strap.
LS13070a
Rear position
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
121
06 09.29
LS13071
Symbol mark
Routing device or upper anchor bracket
Lower anchor bracket
LS13072
Symbol mark
LS13073
the routing device and the anchor
Use bracket to attach the top strap. Upper anchor bracket is installed for front passenger’s seating position, lower anchor bracket is installed for right−rear seating position. This symbol the user ready anchor brackets.
locations of
indicates
TO USE THE ANCHOR BRACKET: Front position— 1. Remove
the passenger head
re-
straint. Lightly push down on the top sur- face of the anchor bracket cover with the symbol mark shown in the illustration, then pull it forward to remove.
2. Fix the child restraint system with
the seat belt. Latch the anchor bracket on the back panel and tight- en the top strap.
the hook onto
For instructions on installing the child re- straint system, see “Child restraint” on page 95 in this Section.
122
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
CAUTION
Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.
Symbol mark
LS13074
LS13075
3. Replace the head restraint. Store the removed cover in a safe place such as the glove box. Be sure to replace the cover when the anchor bracket is not in use.
Rear position— 1. Upper anchor bracket:
Lightly push down on the top sur- face of the upper anchor bracket cover with the symbol mark shown in the illustration, then pull it for- ward to remove. Lower anchor bracket: Pull up the lower anchor bracket.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
123
06 09.29
—Using a top strap (double cab models)
Routing device
LS13076a
LS13077a
LS13051
2. Fix the child restraint system with
the seat belt. Route the routing device as shown in the il- lustration.
top strap
through
the
For instructions on installing the child re- straint system, see “Child restraint” on page 95 in this Section.
CAUTION
Make sure twisted.
the
top strap
is not
3. Latch the hook onto the rear lower anchor bracket and tighten the top strap.
Follow the procedure below for a child restraint system that requires the use of a top strap.
Store the removed covers in a safe place such as the glove box. Be sure to replace the covers when the anchor bracket is not in use.
CAUTION
Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.
124
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
Symbol mark
LS13054a
LS13066
LS13067
Anchor brackets
Use the anchor bracket on the back panel to attach the top strap. Anchor brackets are rear seating position. This symbol indicates the locations of the anchor brackets.
for each
installed
TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.
2. Pull the seatback release strap and swing the seatback forward slightly, then latch the hook onto the anchor bracket. Return the seatback to its original position.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
125
06 09.29
CAUTION
is securely
(cid:1) When returning the seatback to its the original position, make sure seatback locked by pushing forward and rearward on the top of the seatback. Failure to do so will prevent the seat belt from operating properly.
(cid:1) Make sure the top strap is securely latched, and check that the child restraint system is secure by push- ing and pulling it in different direc- tions. Follow all the installation in- structions provided by its manufac- turer.
LS13068
3. Fix the child restraint system with the seat belt and tighten the top strap. Replace the head restraint.
For instructions on installing the child re- straint system, see “Child restraint” on page 95 in this Section.
—Installation with child restraint lower anchorages (regular cab models)
LS13078
Separate seats only
installed
Lower anchorages for Child Restraint Systems equipped with hook or buckle type attachments are in the front passenger seat. The anchorages are installed in the gap between the seat cushion and seatback of the front passenger seat as shown in the illustration. Child Restraint Systems equipped with hook or buckle type attachments can be installed using these anchorages. For such systems, it is not necessary to use the vehicle seatbelts.
126
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
1st lock position
10th lock position
LS13160a
SYSTEM
RESTRAINT
CHILD INSTALLATION 1. Fold down the seatback and back to the 1st lock position (most upright position) until into place. Adjust the seatback to the 10th lock position.
locks
it
LS13082
LS13083
Make sure the seatback is locked secure- ly.
Canada only
Canada only
Type A
Type B
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
127
06 09.29
2. Widen
the gap between
the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback.
the button on
3. Type A—Latch the hooks of
lower the anchorages and
straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.
For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 118 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.
it should be anchored. (For
CAUTION
(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.
(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.
it
(cid:1) After securing
the child restraint system, never slide or recline the seat.
—Installation with child restraint lower anchorages (access cab models)
LS13078
Front seat
LS13099
128
Rear seat
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
installed
Lower anchorages for Child Restraint Systems equipped with hook or buckle type attachments are in the front passenger seat and the right rear auxiliary seat. For front seat without a seatback table— The anchorages are installed in the gap between the seat cushion and seatback as shown in the illustration. For front seat with a seatback table— The anchorages are installed in the seat cushion. Child Restraint Systems equipped with hook or buckle type attachments can be installed using these anchorages. For such systems, it is not necessary to use the vehicle seatbelts. Instructions for installing these types of Child Restraint Systems in the right rear seating area are shown in the illustration on page 131.
CAUTION
To install the child restraint system properly, make sure the bottom cush- ion is flipped over whenever you use a child restraint system in the rear seating area.
1st lock position
10th lock position
LS13160a
SYSTEM
RESTRAINT
CHILD INSTALLATION 1. Front seat—Fold down the front seat seatback and back to the 1st lock position (most upright position) until it locks into place. Adjust the seat- back to the 10th lock position.
LS13082
Make sure the seatback is locked secure- ly.
Canada only
Front seat without seatback table (type A)
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
129
06 09.29
LS13083
LS13186
LS13187
Canada only
Canada only
Canada only
Front seat without seatback table (type B)
Front seat with seatback table (type A)
Front seat with seatback table (type B)
130
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
the gap between
Front seat— 2. Front seat without seatback table— the seat Widen cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback. Front seat with seatback table—Wid- en the seat cushion slightly and confirm the position of the lower anchorages near the but- ton on the seat cushion.
the button on
the slits of
3. Type A—Latch the hooks of
lower the anchorages and
straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.
Rear seat— See the diagrams at right and the in- structions on page 132. For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system.
LS13100
LS13101
Canada only
Canada only
Rear seat (type A)
Rear seat (type B)
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
131
06 09.29
To install a Child Restraint System in the rear seat properly, make sure the bottom seat cushion is flipped over. If the bottom seat cushion is already flipped over, pro- ceed to step 3. 1. Pull the lock release strap. 2. Flip over the bottom cushion.
LS13004a
3. Be sure to follow the Child Restraint System manufacturer’s instructions for the installation proce- dure.
recommended
4. Push and pull the Child Restraint Sys- tem in different directions to ensure a secure installation.
5. If the Child Restraint System shakes or vibrates when used, install a cushion the Child Restraint System between and the flipped−over surface of the seat.
CAUTION
To install the child restraint system properly, make sure the bottom cush- ion is flipped over whenever you use a child restraint system in the rear seating area.
it should be anchored. (For
If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 121 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.
CAUTION
(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.
(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.
it
132
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
(cid:1) After securing
the child restraint system, never slide or recline the seat.
the
lock mechanism of
(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
—Installation with child restraint lower anchorages (double cab models)
LS13084
installed
Lower anchorages for Child Restraint Systems equipped with hook or buckle type attachments are in the rear seat. The anchorages are installed in the gap between the seat cushion and seatback of both outside rear seats as shown in the illustration. Child Restraint Systems equipped with hook or buckle type attachments can be installed using these anchorages. For such systems, it is not necessary to use the vehicle seatbelts.
LS13085
Canada only
Type A
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
133
06 09.29
RESTRAINT
SYSTEM
CAUTION
CHILD INSTALLATION 1. Widen
the gap between
the seat cushion and seatback slightly and confirm the position of the lower an- chorages near the seatback.
the button on
2. Type A—Latch the hooks of
lower the anchorages and
straps onto tighten the lower straps. Type B—Latch the buckles onto the anchorages.
LS13086
For owners in Canada—The symbol on a child restraint system indicates the pres- ence of a lower connector system. If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 124 in this Section.) For installation details, refer to the instruc- tion manual equipped with each product.
it should be anchored. (For
(cid:1) When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.
(cid:1) Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.
it
(cid:1) After securing
the child restraint
system, never recline the seat.
the
lock mechanism of
(cid:1) Do not install a child restraint sys- tem on the rear seat if it interferes with the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sud- den braking or a collision.
Canada only
Type B
134
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
135
06 09.29
SECTION 1− 4
OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt and telescopic steering wheel Outside rear view mirrors Anti−glare inside rear view mirror Auto anti−glare inside rear view mirror Sun visors Vanity mirrors
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
137
137
139
140
141
141
136
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
Tilt and telescopic steering wheel
Outside rear view mirrors—
CAUTION
(cid:1) Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.
(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.
LS14001a
To adjust the steering wheel position, push down the lock release lever. Then tilt the steering wheel to the desired angle, push or pull it to the desired steering column length and pull up the lock release lever.
LS14002
Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
137
06 09.29
—Power rear view mirror control
CAUTION
Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.
LS14003
NOTICE
If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.
To adjust a mirror, use the switches. 1. Master switch—To select the mirror to
be adjusted Push (right).
the switch to “L” (left) or “R”
2. Control switch—To move the mirror
Push the switch in the desired direc- tion.
Mirrors can be adjusted when the key is in the “ACC” or “ON” position.
138
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
—Folding rear view mirrors
Anti−glare inside rear view mirror
LS14004
LS14005
CAUTION
Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious injuries.
The rear view mirrors can be folded backward for parking in compact areas. To fold the rear view mirror, push back- ward.
CAUTION
Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.
Adjust the mirror so that you can just
see the rear of your vehicle in the mir-
ror.
To reduce glare from the headlights of
the vehicle behind you during night
driving, operate the lever on the lower
edge of the mirror.
Daylight driving—Lever at position 1
The reflection in the mirror has greater
clarity at this position.
Night driving—Lever at position 2
Remember that by reducing glare you also
lose some rear view clarity.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
139
06 09.29
Auto anti−glare inside rear view mirror
U14028
Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on.
ignition key
the
is
In automatic function mode, if the mirror detects light from the headlights of the the mirror surface vehicle behind you, darkens slightly the reflected light. To turn off and on the automatic function, push the “
to reduce
” switch.
Adjust it before driving so that the rear view is in the best condition. When the inside air temperature is low, it may take a little longer for the mirror to darken the detection of headlights.
in response
to
CAUTION
Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.
U14029
To ensure correct functioning of anti− glare mirror sensors located on both sides of the mirror, do not touch or cover the sensors with your finger or a piece of cloth, etc.
140
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
Sun visors
Vanity mirrors
LS14009
To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). Type B— If glare comes from obliquely behind you, extend the plate at the end of the visor (position 3).
LS14010
Type A
CAUTION
Type A
Type B— Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti−glare inside rear view mirror and obstruct the rear view.
LS14008
LS14011
Type B
Type B (passenger’s side only)
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
141
06 09.29
Type A— To use the vanity mirrors, swing down the sun visor and slide the cover. Type B— To use the vanity mirror, swing down the sun visor.
142
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
143
06 09.29
SECTION 1− 5
OPERATION OF INSTRUMENTS AND CONTROLS Lights and Wipers Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Personal lights Windshield wipers and washer
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
145
147
147
148
148
149
149
144
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
06 09.29
Headlights and turn signals
LS15001b
For the U.S.A.
LS15002b
For Canada
the
HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, tail, license plate and instrument panel lights For Canada—The tail light indicator (green light) on the instrument panel will tell you that the tail lights are on. Position 2—Headlights and all of above For the U.S.A.—The headlight low beam indicator light (green light) on the instru- ment panel will low beams are on. Automatic light cut off system The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.
tell you
that
the
NOTICE
To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.
2007 TACOMA from Sep. ’06 Prod. (OM35877U)
145
06 09.29
Daytime running light (DRL) system (on some models) The Daytime Running Light (DRL) system can make it easier for others to see the front of your vehicle during the day. The