sand, mud or deep snow. The four–wheel drive indicator light comes on when the “H4”, “N” or “L4” mode is selected. See “(c) Shifting procedure (lever type)” for further instructions.
Use the front drive control lever to se- lect the following transfer modes. “H2” (high speed position, two–wheel drive): Lever at “H2” Use this for normal driving on dry hard– surfaced roads. This position gives greater economy, quietest ride and least wear. “H4” (high speed position, four–wheel drive): Lever at “H4” Use this for normal driving on wet, icy or roads. This position pro- snow–covered vides greater traction two–wheel drive.
than
134
2003 MY TACOMA (OM35800U)
Use the front drive control lever and “4WD” button to select the following transfer modes. “H2” (high speed position, two–wheel drive): Lever at “H”, “4WD” button left out Use this for normal driving on dry hard– surfaced roads. This position gives greater economy, quietest ride and least wear. “H4” (high speed position, four–wheel drive): Lever at “H”, “4WD” button pushed in Use this for normal driving on wet, icy or roads. This position pro- snow–covered vides greater traction two–wheel drive.
than
’03 Tacoma U (L/O 0209)
“N” (neutral position): Lever at “N” No power is delivered to the wheels. The vehicle must be stopped. “L4” (low speed position, four–wheel drive): Lever at “L4” Use this for maximum power and traction. Use “L4” for climbing or descending steep hills, off–road driving, and hard pulling in sand, mud or deep snow. The four–wheel drive indicator light comes on when the “H4”, “N” or “L4” mode is selected. See “(c) Shifting procedure (lever/button type)” for further instructions.
(b) A.D.D. (automatic disconnecting differential) The A.D.D. can be engaged or disen- gaged by the shifting operations de- scribed in “(c) Shifting procedure”. You should drive in four–wheel drive for at least 16 km (10 miles) each month. This will assure that the front drive com- ponents are lubricated.
(c) Shifting procedure (lever type with manual transmission) SHIFTING BETWEEN “H2” AND “H4” To shift from “H2” to “H4”, reduce your speed to less than 80 km/h (50 mph) and move lever. You need not depress the clutch pedal. If you have trouble shifting in cold weath- er, reduce your speed or stop the vehicle and reshift.
the front drive control
CAUTION
Never move the front drive control lever if wheels are slipping. Stop the slipping or spinning before shifting.
To shift from “H4” to “H2”, simply move the front drive control lever. This can be done at any vehicle speed. You need not depress the clutch pedal. If the indicator light does not go off when you shift “H2”, drive straight ahead while accelerating or decel- erating, or drive in reverse.
transfer
into
the
2003 MY TACOMA (OM35800U)
135
’03 Tacoma U (L/O 0209)
SHIFTING BETWEEN “H4” AND “L4” To shift from “H4” to “L4”, stop the vehicle or reduce your speed to less than 8 km/h (5 mph). With your foot off the accelerator pedal, depress the clutch ped- al and move the front drive control lever. To shift from “L4” to “H4”, depress the clutch pedal and move the front drive con- trol lever. This can be done at any vehicle speed.
(c) Shifting procedure (lever type with automatic transmission) SHIFTING BETWEEN “H2” AND “H4” To shift from “H2” to “H4”, reduce your speed to less than 80 km/h (50 mph) and move the front drive control lever. If you have trouble shifting in cold weath- er, reduce your speed or stop the vehicle and reshift.
CAUTION
Never move the front drive control lever if wheels are slipping. Stop the slipping or spinning before shifting.
the
into
transfer
To shift from “H4” to “H2”, simply move the front drive control lever. This can be done at any vehicle speed. If the indicator light does not go off when you shift “H2”, drive straight ahead while accelerating or decel- erating, or drive in reverse. SHIFTING BETWEEN “H4” AND “L4” To shift between “H4” and “L4”, stop the vehicle and put the transmission in “N”. With your the brake pedal, move the front drive control lever.
foot holding down
(c) Shifting procedure (lever/button type with manual transmission) SHIFTING BETWEEN “H2” AND “H4” To shift from “H2” to “H4”, reduce your speed to less than 100 km/h (62 mph) and push in the “4WD” button. You need not depress the clutch pedal. If the indicator light does not come on when you push in the “4WD” button, drive straight ahead while accelerating or decel- erating. If the indicator light flashes and the buzz- er sounds when you push in the “4WD” button, reduce your speed or stop the vehicle and reset.
CAUTION
if Never push wheels are slipping. Stop the slipping or spinning before shifting.
the “4WD” button
To shift from “H4” to “H2”, push the “4WD” button again to turn it off. This can be done at any vehicle speed. You need not depress the clutch pedal. If the indicator light does not go off when you shift “H2”, drive straight ahead while accelerating or decel- erating, or drive in reverse.
transfer
into
the
136
2003 MY TACOMA (OM35800U)
the accelerator pedal, depress
SHIFTING BETWEEN “H2” OR “H4” AND “L4” To shift from “H2” or “H4” to “L4”, stop the vehicle or reduce your speed to less than 8 km/h (5 mph). With your foot off the clutch pedal and move the front drive con- trol lever. To shift from “L4” to “H2” or “H4”, depress the clutch pedal and move the front drive control lever. When the “4WD” button is pushed in, the transfer shifts into “H4”; when the the button transfer shifts into “H2”. This can be done at any vehicle speed. If the indicator light does not go off when you shift “H2”, drive straight ahead while accelerating or decel- erating, or drive in reverse.
left out,
transfer
into
the
is
’03 Tacoma U (L/O 0209)
(c) Shifting procedure (lever/button type with automatic transmission) SHIFTING BETWEEN “H2” AND “H4” To shift from “H2” to “H4”, reduce your speed to less than 100 km/h (62 mph) and push in the “4WD” button. If the indicator light does not come on when you push in the “4WD” button, drive straight ahead while accelerating or decel- erating. If the indicator light flashes and the buzz- er sounds when you push in the “4WD” button, reduce your speed or stop the vehicle and reset.
CAUTION
Never push if wheels are slipping. Stop the slipping or spinning before shifting.
the “4WD” button
SHIFTING BETWEEN “H2” OR “H4” AND “L4” To shift from “H2” or “H4” to “L4”, stop the vehicle and put the transmission in “N”. With your foot holding down the brake pedal, move the front drive control lever. To shift from “L4” to “H2” or “H4”, stop the vehicle and put the transmission in “N”. With your foot holding down the brake pedal, move the front drive control lever. When the “4WD” button is pushed in, the transfer shifts into “H4”; when the button is left out, the transfer shifts into “H2”. If the indicator light does not go off when you shift “H2”, drive straight ahead while accelerating or decel- erating, or drive in reverse.
transfer
into
the
To shift from “H4” to “H2”, push the “4WD” button again to turn it off. This can be done at any vehicle speed. If the indicator light does not go off when you shift “H2”, drive straight ahead while accelerating or decel- erating, or drive in reverse.
transfer
into
the
2003 MY TACOMA (OM35800U)
137
’03 Tacoma U (L/O 0209)
Rear differential lock system
CAUTION
Do not use the rear differential lock in the conditions other than above. Large steering effort and careful cor- nering control will be required.
The rear differential lock system is pro- vided for use only when wheel spinning occurs in a ditch or on a slippery or ragged surface. This differential lock system is effective in case one of the rear wheels is spinning. Except for Pre Runner models Before using the rear differential lock sys- tem, first shift the front drive control into “L4” to see if it works. If this has no effect, additionally use the rear differential lock system.
138
2003 MY TACOMA (OM35800U)
To lock the rear differential, push the switch. Be sure to stop the wheels before locking the differential. For easy locking, depress the clutch ped- al, push the lock switch and slowly re- lease the clutch pedal. the The switch is turned on. Wait a few seconds for the system to complete operation. Af- ter the differential is locked, the light will stop blinking and remain on. The anti–lock brake system does not oper- ate when the rear differential is locked. It is normal operation for the “ABS” warning light to be on at this time.
light will blink when
indicator
’03 Tacoma U (L/O 0209)
Parking brake
To check the indicator bulb, turn the igni- tion key to the “ON” position, but do not start the engine.
CAUTION
Do not keep driving with the differen- tial lock switch on.
CAUTION
stopped
(cid:1) Do not lock the differential until the wheels have spinning. Otherwise, the vehicle may move in an unexpected direction when the differential lock is engaged, result- ing in an accident. This may also lead to possible damage to differen- tial lock component parts.
(cid:1) Do not drive over 8 km/h (5 mph)
when the differential is locked.
the
the differential, push
To unlock switch once again. Unlock the differential as soon as the ve- hicle moves out. For easy unlocking, slightly turn the steer- ing wheel in either direction while the ve- hicle is in motion. When the differential lock is disengaged, the indicator light will go out. Except for Pre Runner models The differential will also unlock if you shift the front drive control lever out of “L4”. Never forget to turn off the switch after using this feature.
first depress
When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Pull out on the lever. For better holding power, the brake pedal and hold it while setting the parking brake. To release: Press the lock release button (1), the then push it in (3). To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.
lever clockwise (2),
turn
2003 MY TACOMA (OM35800U)
139
’03 Tacoma U (L/O 0209)
CAUTION
Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.
Cruise control
The cruise control allows you to cruise
the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off
the accelerator pedal.
Your cruising speed can be maintained up
or down grades within the limits of engine
performance, although a slight speed
change may occur when driving up or
down
the grades. On steeper hills, a
greater speed change will occur so it is
better to drive without the cruise control.
CAUTION
(cid:1) To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow–covered) or winding roads.
If
(cid:1) Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.
140
2003 MY TACOMA (OM35800U)
TURNING ON THE SYSTEM To operate the cruise control, press the “CRUISE ON–OFF” button. This turns the system on. The the instrument panel shows that you can now set the vehicle at a desired cruising speed. Another press will turn the system completely off.
indicator
light
in
CAUTION
To avoid accidental cruise control en- gagement, keep the “CRUISE ON– OFF” switch off when not using the cruise control.
’03 Tacoma U (L/O 0209)
If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration.
CAUTION
For manual transmission: While driving with the cruise control on, do not shift to neutral without depressing the clutch pedal, as this may cause engine racing or over–rev- ving.
CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling
lever
the
the
in
“CANCEL”
direction and releasing it
b. Depressing the brake pedal c. Depressing
the clutch pedal (manual
transmission)
If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto-
matically cancel out.
If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset
speed will also automatically cancel out.
2003 MY TACOMA (OM35800U)
If the preset speed automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity. RESETTING TO A FASTER SPEED Push the lever up in the “RES/ACC” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “SET/COAST” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “SET/COAST” direction and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “SET/COAST” direction.
141
SETTING AT A DESIRED SPEED
On vehicles with automatic transmission,
the transmission must be in “D” before
you set the cruise control speed.
Bring your vehicle to the desired speed,
push the lever down in the “SET/COAST”
direction and release it. This sets the ve-
hicle at that speed. If the speed is not
satisfactory, tap the lever up for a faster
speed, or tap it down for a slower speed.
Each tap changes the set speed by 1.6
km/h (1.0 mph). You can now take your
foot off the accelerator pedal.
If you use
On vehicles with automatic transmission, even if you turn off the overdrive switch with the cruise control on, engine braking will not be applied because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. the brake pedal, cruise control is cancelled. RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal or clutch pedal, pushing the lever up in the “RES/ACC” direction will restore the speed set prior to cancellation. However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed.
lever or by depressing
’03 Tacoma U (L/O 0209)
Clutch start cancel switch (four–wheel drive models with manual transmission)
in
the
light
indicator
“CRUISE”
CRUISE CONTROL FAILURE WARNING If the instrument cluster flashes when using the cruise control, press the “CRUISE ON– OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. (cid:1) The indicator light does not come on. (cid:1) The indicator light flashes again. (cid:1) The
light goes out after
indicator
it
comes on.
If this is the case, contact your Toyota dealer and have your vehicle inspected.
To crank the engine without depressing the clutch pedal, push the switch with the ignition on. The switch stays on as long as the igni- tion is on. And it will automatically turn off when the ignition is off. An indicator light will illuminate to indicate the system is operating. This switch cancels the clutch start sys- tem, which is designed to keep the starter motor from operating if the clutch pedal is not depressed all the way down. The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged.
142
2003 MY TACOMA (OM35800U)
Never use the switch for normal engine starting. Be sure the starting procedure instructed in “How to start the engine” in Section 3.
follow
to
’03 Tacoma U (L/O 0209)
2003 MY TACOMA (OM35800U)
143
’03 Tacoma U (L/O 0209)
144
2003 MY TACOMA (OM35800U)
’03 Tacoma U (L/O 0209)
SECTION 1– 7
OPERATION OF INSTRUMENTS AND CONTROLS Car audio system Reference Using your audio system Car audio system operating hints
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
146
146
166
2003 MY TACOMA (OM35800U)
145
’03 Tacoma U (L/O 0209)
Reference
Type 1: AM·FM radio (with cassette and compact disc auto changer controllers)
Type 3: AM·FM radio/cassette player/com- pact disc player (with compact disc auto changer controller)
Type 2: AM·FM radio/cassette player (with
compact disc auto changer controller)
146
2003 MY TACOMA (OM35800U)
“TAPE”,
turn on
“FM1·2”,
“AM”, to
Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR/VOL” or “PWR·VOL” to turn the audio system on and off. Push “AUX” pushing “PWR/VOL” or “PWR·VOL”. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “CD” or “AUX” if the system is already on but you want to switch from one function to anoth- er.
“CD” or function without
“FM1·2”,
“TAPE”,
“AM”,
that
’03 Tacoma U (L/O 0209)
TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.
YOUR RADIO ANTENNA To remove an antenna, carefully turn it counterclockwise.
NOTICE
To prevent damage to the antenna, make sure it is removed before driv- ing your Toyota through an automatic car wash.
YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should face to the right.
NOTICE
Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.
YOUR COMPACT DISC PLAYER When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The compact disc player will play from track 1 through the end of the disc. Then it will play from track 1 again. On models with the compact disc auto changer, next disc will be played from track 1.
NOTICE
Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.
The player is intended for use with 12 cm (4.7 in.) discs only.
2003 MY TACOMA (OM35800U)
147
’03 Tacoma U (L/O 0209)
—Controls and features
(cid:1)Type 1
Details of specific buttons, controls, and features are described in the alphabetical list that follows.
148
2003 MY TACOMA (OM35800U)
’03 Tacoma U (L/O 0209)
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE” knob or “SEEK” button.) Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM1·2”.)
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which ” indicates side is currently selected (“ top side, “ Auto–reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
(Reverse/Fast forward buttons)
the
the
fast
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto–re- verse feature. Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing.
AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CTRL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. For “CTRL appears on knob to suit your preference. The display will show the “BAS –5” to “BAS 5”. For high–pitch “CTRL appears on knob to suit your preference. The display will show the “TRE –5” to “TRE 5”.
tone adjustment, push / MODE” repeatedly until “TRE” the
tone adjustment, push / MODE” repeatedly until “BAS” the
the display. Then
the display. Then
to adjust
low–pitch
is used
range
range
turn
turn
from
from
tone
2003 MY TACOMA (OM35800U)
149
’03 Tacoma U (L/O 0209)
the
from
range
to adjust
is also used
left/right adjustment, push “CTRL
Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For front/rear adjustment, push “CTRL / MODE” repeatedly until “FAd” appears on the display. Then turn the knob to adjust the front/rear balance. The display will show “FAd–F7” to “FAd–R7”. For MODE” repeatedly until “BAL” appears on the display. Then turn the knob to adjust the left/right balance. The display will show “BAL–L7” to “BAL–R7”. AUX (Auxiliary button) This button is used to operate each player when a cassette tape player, compact disc player or compact disc auto changer is equipped with this radio player. With cassette tape player Push “AUX” to switch from radio to cas- sette operation. If the audio system is off, you can turn on the cassette player by pushing “AUX”. In both cases, a cassette must already be loaded in the player.
range
from
the
in
loaded
With compact disc player or compact disc auto changer Push “AUX” to switch from radio to com- pact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “AUX”. In both cases, a disc must already be the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each time you push “AUX”, the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.
inserted up–side down. Clean
loaded
inside
it the
is
150
2003 MY TACOMA (OM35800U)
If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC (cid:2)(cid:1) Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, push the button marked with the double–D symbol. The double–D symbol will appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape.
B NR*
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn
on the radio by pushing “FM1·2”. Also,
push “FM1·2” to switch from cassette or
compact disc operation to radio operation.
PWR/VOL (Power/Volume)
Push “PWR/VOL” to turn the audio system
on and off. Turn “PWR/VOL” to adjust the
volume.
RAND (Random)
There are two random features—you can
either listen to the tracks on all the com-
pact discs in the magazine in random or-
der, or only
tracks on a
specific compact disc in random order.
listen
the
to
’03 Tacoma U (L/O 0209)
the
in the
random
turn off
To randomly play the tracks on the disc: Quickly push and release “RAND”. “RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To feature, push “RAND” again. Compact disc auto changer only— To randomly play all the tracks magazine: Push and hold “RAND” until you hear a beep. “ ·RAND” will appear on the dis- play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push “RAND” again. RPT (Repeat) Cassette Player is playing. Push “RPT” while “RPT” will appear on the display. When the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
track ends,
track
the
Compact Disc Player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a beep. “ ·RPT” will appear on the dis- play. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back the disc and replay. This process will be continued until you push the button again to turn off the repeat feature.
to the top track of
2003 MY TACOMA (OM35800U)
151
’03 Tacoma U (L/O 0209)
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold “SCAN” until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
“SCAN” again.
To scan all the frequencies:
Quickly push and release “SCAN”. If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push “SCAN” again.
Compact disc player
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “(cid:1)” or “(cid:2)” under the “SEEK”. Do this again to find another station.
the radio finds and the next station up or down the
·SCAN” will appear on
the seek mode,
“SCAN” again.
If
152
2003 MY TACOMA (OM35800U)
Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. (cid:2) After tape
the beginning of
is the player will automatically
reached, start playing the same side.
the
’03 Tacoma U (L/O 0209)
TUNE (Tuning) Turn the knob clockwise to step up the frequency. Turn the knob counterclockwise to step down the frequency.
2003 MY TACOMA (OM35800U)
153
(cid:2) After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly.
the beginning of
to
’03 Tacoma U (L/O 0209)
(cid:1)Type 2
Details of specific buttons, controls, and features are described in the alphabetical list that follows.
154
2003 MY TACOMA (OM35800U)
’03 Tacoma U (L/O 0209)
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE” knob or “SEEK” button.) Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM1·2”.)
(Eject button) the cassette
Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which ” indicates side is currently selected (“ top side, “ Auto–reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
(Reverse/Fast forward buttons)
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”. If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto–re- verse feature.
fast
the
the
Compact Disc Player If you want forward or reverse to fast through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation. CTRL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. For “CTRL appears on knob to suit your preference. The display will show the “BAS –5” to “BAS 5”.
tone adjustment, push / MODE” repeatedly until “BAS” the
the display. Then
to adjust
low–pitch
is used
range
turn
from
tone
2003 MY TACOMA (OM35800U)
155
’03 Tacoma U (L/O 0209)
from
turn
range
to adjust
is also used
the display. Then
left/right adjustment, push “CTRL
tone adjustment, push / MODE” repeatedly until “TRE” the
For high–pitch “CTRL appears on knob to suit your preference. The display will show the “TRE –5” to “TRE 5”. Sound balance adjustment function— This knob the sound balance between the front and rear, and the right and left speakers. For MODE” repeatedly until “BAL” appears on the display. Then turn the knob to adjust the left/right balance. The display will show “BAL–L7” to “BAL–R7”. Models with rear speakers—for front/rear adjustment, push “CTRL / MODE” repeat- edly until “FAd” appears on the display. Then turn the knob to adjust the front/rear balance. The display will show “FAd–F7” to “FAd–R7”.
range
range
from
from
the
the
time you push “CD”,
CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages. If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc.
inserted up–side down. Clean
loaded
inside
it the
is
156
2003 MY TACOMA (OM35800U)
If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer. DISC (cid:2)(cid:1) Compact disc auto changer only— By using this button, you can select a disc you wish to listen to. Push either side of the button until the number of the disc you want to listen to appears on the display. Dolby(cid:3) If you are listening to a tape that was recorded with Dolby(cid:3) B Noise Reduction, push the button marked with the double–D symbol. The double–D symbol will appear on the display. Push the button again to turn off Dolby(cid:3) B NR. The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used for recording the tape.
B NR*
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn
on the radio by pushing “FM1·2”. Also,
push “FM1·2” to switch from cassette or
compact disc operation to radio operation.
PWR/VOL (Power/Volume)
Push “PWR/VOL” to turn the audio system
on and off. Turn “PWR/VOL” to adjust the
volume.
RAND (Random)
There are two random features—you can
either listen to the tracks on all the com-
pact discs in the magazine in random or-
der, or only
tracks on a
specific compact disc in random order.
listen
the
to
’03 Tacoma U (L/O 0209)
the
in the
random
turn off
To randomly play the tracks on a disc: Quickly push and release “RAND”. “RAND” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To feature, push “RAND” again. Compact disc auto changer only— To randomly play all the tracks magazine: Push and hold “RAND” until you hear a beep. “ ·RAND” will appear on the dis- play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push “RAND” again. RPT (Repeat) Cassette Player is playing. Push “RPT” while “RPT” will appear on the display. When the it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
track ends,
track
the
Compact Disc Player There are two repeat features—you can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” while the track is playing. “RPT” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “RPT” until you hear a beep. “ ·RPT” will appear on the dis- play. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back the disc and replay. This process will be continued until you push the button again to turn off the repeat feature.
to the top track of
2003 MY TACOMA (OM35800U)
157
’03 Tacoma U (L/O 0209)
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold “SCAN” until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
“SCAN” again.
To scan all the frequencies:
Quickly push and release “SCAN”. If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push “SCAN” again.
Compact disc player
There are two scan features—you can ei-
ther scan the tracks on a specific disc or
scan the first tracks of all the discs in the
magazine.
Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ the display and the player will perform the first track of the next disc. To select a disc, push the the player has scanned all the discs, it will stop scan- ning. SEEK (Seeking) Radio In plays station band. To seek a station, quickly push and re- lease the “(cid:1)” or “(cid:2)” under the “SEEK”. Do this again to find another station.
the radio finds and the next station up or down the
·SCAN” will appear on
the seek mode,
“SCAN” again.
If
158
2003 MY TACOMA (OM35800U)
Cassette Player By using this button, you can skip up or down to a different track. You can skip up to nine tracks at a time. Push the up or down side of the button. “FF 1” or “REW 1” will appear on the display. Next, push either side of the track button until the number on the display reaches the number of tracks you want to skip. If you push the button ten times, the skip feature will be turned off. When counting the number of tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two be- fore the song you are listening to, push on the down side of the button until “REW 3” appears on the display. If you have pushed the track button more than you wanted to, push the other side of the button. The track number will be reduced. The track number you select is not valid if it is higher than the number of tracks remaining on the current cassette side. (cid:2) After tape
the beginning of
is the player will automatically
reached, start playing the same side.
the
’03 Tacoma U (L/O 0209)
TRACK (Track up/down button): Compact disc player By using this button, you can skip up or down to a different track. Push either side of the track button until the number of the track you want to listen to appears on the display. If you want to return the current track, push the down side of the button one time, quickly. TUNE (Tuning) Turn the knob clockwise to step up the frequency. Turn the knob counterclockwise to step down the frequency.
the beginning of
to
(cid:2) After the end of the tape is reached, the player will automatically reverse sides and start playing the other side. There must be at least 3 seconds of blank space between tracks for the track button to work correctly. In addition, the feature may not work well with some spoken word, live, or classical recordings. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push “TAPE” to switch from radio or com- pact disc operation to cassette operation. If the audio system is off, you can turn on the cassette player by pushing “TAPE”. In both cases, a cassette must already be loaded in the player.
2003 MY TACOMA (OM35800U)
159
’03 Tacoma U (L/O 0209)
(cid:1)Type 3
Details of specific buttons, controls, and features are described in the alphabetical list that follows.
160
2003 MY TACOMA (OM35800U)
’03 Tacoma U (L/O 0209)
to preset and
1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. (See “TUNE” knob or “SEEK” button.) Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To tune in to a preset station: Push the button for the station you want. The but- ton number and station frequency will ap- pear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM1·2”.)
(Eject button) the cassette
Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc. After you turn the ignition to “LOCK”, you will be able to eject a cassette or disc but you will not be able to reinsert it.
(Program)
Push “ ” to select the other side of a cassette tape. The display indicates which ” indicates side is currently selected (“ top side, “ Auto–reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.
” indicates bottom side). feature: After
(Reverse/Fast forward buttons)
Cassette Player Push the fast forward button to fast for- ward a cassette tape. “FF” will appear on the display. Push the reverse button to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push forward button or “TAPE”; to stop the tape while it is re- winding, push reverse button or “TAPE”.
fast
the
the
If a tape side rewinds completely, the cas- sette player will stop and then play that same side. If a tape fast forwards com- pletely, the cassette player will play the other side of the tape, using the auto–re- verse feature. Compact Disc Player If you want to fast forward or reverse through a compact disc track, push and hold in the fast forward or reverse button. When you release the button, the compact disc player will resume playing. AM Push “AM” to turn on the radio and select the AM band. “AM” will appear on the display. If the audio system is off, you can turn on the radio by pushing “AM”. Also, push “AM” to switch from cassette or compact disc operation to radio operation.
2003 MY TACOMA (OM35800U)
161
’03 Tacoma U (L/O 0209)
the
from
from
range
range
the knob
the knob
the display. Then
the display. Then
For front/rear adjustment, push “CONTROL / MODE” repeatedly until “FAd” appears on turn to adjust the front/rear balance. The display will show the “FAd–F7” to “FAd–R7”. For left/right adjustment, push “CONTROL / MODE” repeatedly until “BAL” appears on to turn adjust the left/right balance. The display will show “BAL–L7” to “BAL–R7”. CD (Compact Disc) Push “CD” to switch from radio or cas- sette operation to compact disc operation. If the audio system is off, you can turn on the compact disc player by pushing “CD”. In both cases, a disc must already be loaded in the player. When the audio is set into compact disc operation, the display shows the track or, track and disc number currently being played. Each the system changes to the automatic changer. If the player malfunctions, your audio sys- tem will display one of the six following error messages.
time you push “CD”,
inserted up–side down. Clean
If “WAIT” appears on the display, it indi- cates that the inside of the player unit may be too hot due to the very high ambi- ent temperature. Remove the disc or mag- azine from the player and allow the player to cool down. If “Err 1” appears on the display, it indicates the disc is dirty, damaged, or it was the disc or insert it correctly. If “Err 2” appears on the display, indicates no disc magazine. Insert a disc. If “Err 3” or “Err 4” appears on the display, it indicates there is a trouble in- side the system. Eject the disc or maga- zine. Set the disc or magazine again. If “OPEn” appears on the display, it indicates the compact disc auto changer lid is open. Close the compact disc auto changer lid. If the malfunction is not rectified, take your vehicle to your Toyota dealer.
loaded
inside
it the
is
the
tone
from
range
is used
low–pitch
to adjust
/ MODE”
CONTROL / MODE (Audio control and mode adjustment) Manual tone adjustment function— This knob the manually. tone adjustment, push For “CONTROL repeatedly until “BAS” appears on the display. Then turn the knob to suit your preference. The display will show “BAS –5” to “BAS 5”. For middle–pitch tone adjustment, push “CONTROL / MODE” repeatedly until “MId” appears on the knob to suit your preference. The display will show the range from “MId –5” to “MId 5”. tone adjustment, push For high–pitch “CONTROL repeatedly until “TRE” appears on the display. Then turn the knob to suit your preference. The display will show “TRE –5” to “TRE 5”. Sound balance adjustment function— the This knob sound balance between the front and rear, and the right and left speakers.
the display. Then
is also used
/ MODE”
to adjust
range
turn
from
the
162
2003 MY TACOMA (OM35800U)
’03 Tacoma U (L/O 0209)
B NR*
DISC (cid:2)(cid:1)
Compact disc auto changer only—
By using this button, you can select a
disc you wish to listen to.
Push either side of the button until the
number of the disc you want to listen to
appears on the display.
Dolby(cid:3)
If you are listening to a tape that was
recorded with Dolby(cid:3) B Noise Reduction,
push the button marked with the double–D
symbol. The double–D symbol will appear
on the display. Push the button again to
turn off Dolby(cid:3) B NR.
The Dolby NR mode reduces tape noise
by about 10 dB. For best sound reproduc-
tion, play your tapes with this button on
or off according to the mode used for
recording the tape.
: Dolby noise reduction manufactured under license from
Dolby Laboratories Licensing Corporation. “DOLBY” and the
double D symbol
are trademarks of Dolby Laboratories
Licensing Corporation.
FM1·2
Push “FM1·2” to turn on the radio and
select the FM band. “FM1” or “FM2” will
appear on the display. This system allows
you to set twelve FM stations, two for
each button.
If the audio system is off, you can turn on the radio by pushing “FM1·2”. Also, push “FM1·2” to switch from cassette or compact disc operation to radio operation. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on all the com- pact discs in the magazine in random or- der, or only tracks on a specific compact disc in random order. To randomly play the tracks on a disc: Quickly push and release “ ” will appear on the display. The disc you are listening to will play in random order. If you hear a beep, you held the button too long, and the player will play all the tracks in the magazine in random order. To turn off the random feature, push this button again.
listen
the
”. “
to
in the
Compact disc auto changer only— To randomly play all the tracks magazine: ” until you hear a Push and hold “ ” will appear on the dis- beep. “ play and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the random fea- ture, push this button again. RPT (Repeat) Cassette Player
” while the track is playing. Push “ ” will appear on the display. When “ the track ends, it will automatically be rewound and replayed. This process will be continued until you push the button again to turn off the repeat feature. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly.
2003 MY TACOMA (OM35800U)
163
’03 Tacoma U (L/O 0209)
Compact Disc Player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “ ” while the track is playing. “ ” will appear on the display. If you hear a beep, you held the button too long, and the player will repeat the whole disc. When the track ends, it will automatically be replayed. This pro- cess will be continued until you push the button again to turn off the repeat feature. Compact disc auto changer only— Repeating a disc: Push and hold “ ” until you hear a ” will appear on the display. beep. “ The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the top track of the disc and replay. This process will be continued until you push the button again to turn off the re- peat feature.
SCAN
Radio
You can either scan all the frequencies on
a band or scan only the preset stations
for that band.
To scan the preset stations:
Push and hold “SCAN” until you hear a
beep. The radio will tune in the next pres-
et station up the band, stay there for 5
seconds, and then move to the next pre-
set station. To select a station, push
“SCAN” again.
To scan all the frequencies:
Quickly push and release “SCAN”. If you
hear a beep, you held the button too long,
and the radio will scan the preset sta-
tions. The radio will find the next station
up the station band, stay there for 5 se-
conds, and then scan again. To select a
station, push “SCAN” again.
164
2003 MY TACOMA (OM35800U)
Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “SCAN”. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are listening to. If you hear a beep, you held the button too long, and the player will scan the first track of all the discs in the magazine. To select a track, push “SCAN” again. If the player scanned all the tracks on the disc, it will stop scan- ning. Compact disc auto changer only— Scanning the first track of all the discs in the magazine: “SCAN” until you hear a beep. Push “ the display and the player will perform the first track of the next disc. To select a disc, push the the player has