2011 Toyota Matrix Owners Manual

Select “Delete Entry” using a voice command or

STEP 2

Select the data to be deleted by either of the following meth- ods, and select “Confirm” using a voice command or

a. Press the talk switch, and say the name of the desired

phone number to be deleted.

b. Press the talk switch, say “List phones”. While the name of the desired phone number is being read aloud, press the talk switch.

Deleting speed dials

STEP 1

Select “Delete Speed Dial” using a voice command or

STEP 2

Press the preset button in which the desired speed dial is reg-

istered, and select “Confirm” using a voice command or

280

3-4. Using the hands-free phone system (for cellular phone)

Listing the registered data

Selecting “List names” using a voice command causes a list of the registered data to be read aloud. When listing is complete, the system returns to “Phonebook”. Pressing the talk switch while the desired data is being read aloud selects the data, and the following function will be available. • Dialing: “Dial” • Changing a registered name: “Change Name” • Deleting an entry: “Delete Entry” • Setting a speed dial: “Speed Dial (Set speed dial)”

■Limitation of number of digits

A phone number that exceeds 24 digits cannot be registered.

281

3-5. Using the interior lights Interior lights list

Personal/interior lights or personal lights (→P. 284, 285) Interior lights (→P. 283)

282

3-5. Using the interior lights

Interior light

■Illuminated entry system Vehicles with moon roof

When the light switch is in the “DOOR” position, the interior lights and per- sonal/interior lights automatically turn on/off according to the engine switch position, whether the doors are locked/unlocked (with power door lock sys- tem) and whether the doors are open/closed.

Vehicles without moon roof

When the light switch is in the “DOOR” position, the interior lights automati- cally turn on/off according to the engine switch position, whether the doors are locked/unlocked (with power door lock system) and whether the doors are open/closed.

■To prevent the battery from being discharged

If the interior lights and personal/interior lights (vehicles with moon roof) remain on when the door is not fully closed and the light switch is in the “DOOR” position, the lights will go off automatically after 20 minutes.

■Customization that can be configured at Toyota dealer

Settings (e.g. The time elapsed before lights turn off) can be changed. (Customizable features →P. 472)

Interior light

“DOOR” position Off On

283

3-5. Using the interior lights

Personal/interior lights

Personal/interior lights (vehicles with moon roof)

■ Interior lights

“DOOR” position Off On

■ Personal lights

On/off

284

3-5. Using the interior lights

Personal lights

Personal lights (vehicles without moon roof)

On/off

285

3-6. Using the storage features List of storage features

Auxiliary boxes Glove box Bottle holders Cup holders Console box

CAUTION

■Items that should not be left in the storage spaces

Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: ●Glasses may be deformed by heat or cracked if they come into contact

with other stored items.

●Lighters or spray cans may explode. If they come into contact with other stored items, the lighter may catch fire or the spray can may release gas, causing a fire hazard.

286

3-6. Using the storage features

Glove box and console box

Glove box

Pull up the lever.

CAUTION

■Caution while driving

Keep the glove box closed. Injuries may result in the event of an accident or sudden braking.

Console box

Lift the lid while pulling the lever.

CAUTION

■Caution while driving

Keep the console box closed. Injuries may result in the event of an accident or sudden braking.

287

3-6. Using the storage features

Cup holders

Front

Cup holders

Rear

Pull the lid to open.

■Using the cup holder (front) to store small items

Remove the holders.

288

3-6. Using the storage features

Cup holders

■Adjusting the cup holder to the size of the cups or drink-cans

Remove holder position.

the holder and change

the

Small size Middle size Large size

CAUTION

■Items unsuitable for the cup holder

Do not place anything other than cups or aluminum cans in the cup holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury. If possible, cover hot drinks to prevent burns.

■When not in use

Keep the rear cup holders closed. Injuries may result in the event of an accident or sudden braking.

289

Bottle holders

3-6. Using the storage features

Bottle holders

Front

Rear

CAUTION

■Items unsuitable for the bottle holder

Do not place anything other than pet bottles in the bottle holders. Other items may be thrown out of the holders in the event of an accident or sudden braking and cause injury.

290

3-6. Using the storage features

Bottle holders and auxiliary boxes

NOTICE

■When a pet bottle is in the front bottle holder (vehicles with manual

window)

As there is a possibility of interfering with a manual window regulator handle, pre- vent the window from opening and clos- ing, do not place a pet bottle in the holder when turning the handle.

Auxiliary boxes

Front

Pull up the lever.

Overhead console (vehicles with moon roof)

Push the lid.

291

3-6. Using the storage features

CAUTION

■Caution while driving

Auxiliary boxes

Keep the auxiliary boxes closed. Injuries may result in the event of an accident or sudden braking.

■Items unsuitable for storing (overhead console only)

Do not store items heavier than 0.4 lb. (0.2 kg). Doing so may cause the auxiliary box to open and the items inside may fall out, resulting in an accident.

292

3-7. Other interior features Sun visors

Forward position: Flip down. Side position: Flip down, unhook, and swing to the side.

293

3-7. Other interior features Vanity mirrors

Slide the cover.

294

3-7. Other interior features Clock

to

Adjusts the hour. Adjusts the minutes. Rounds hour.* *: e.g. 1:00 to 1:29 → 1:00
1:30 to 1:59 → 2:00

the nearest

■The clock is displayed when

The engine switch is in the “ACC” or “ON” position.

295

3-7. Other interior features Ashtrays∗

An ashtray can be installed in a cup holder.

CAUTION

■When not in use

Keep the ashtray closed. Injuries may result in the event of sudden braking, sudden swerving or an accident.

■To prevent fire

●Fully extinguish matches and cigarettes before putting them in the ashtray,

then make sure the ashtray is fully closed.

●Do not place paper or any other type of flammable object in the ashtray.

296

∗: If equipped

3-7. Other interior features Cigarette lighter∗

the cigarette

lighter

Push down.

The cigarette lighter will pop up when it is ready for use.

■The cigarette lighter can be used when

The engine switch is in the “ACC” or “ON” position.

CAUTION

■To avoid burns or fires

●Do not touch the metal parts of the cigarette lighter. ●Do not hold the cigarette lighter down. It could overheat and cause a fire. ●Do not insert anything other than the cigarette lighter into the outlet.

∗: If equipped 297

3-7. Other interior features Power outlet∗

The power outlet can be used for a following component.

12 V: Accessories that run on less than 10 A. 115 V: Accessories that uses less than 100 W. Type A (12 V)

Type B (115 V)

■The power outlet can be used when

12 V

The engine switch is in the “ACC” or “ON” position.

115 V

The engine switch is in the “ON” position.

298

∗: If equipped

3-7. Other interior features

NOTICE

■To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short cir- cuit.

■To prevent the fuse from being blown

12 V

Do not use an accessory that uses more than 12 V 10 A.

115 V

Do not use a 115 V appliance that requires more than 100 W. If a 115 V appliance that consumes more than 100 W is used, the protection circuit will cut the power supply.

■To prevent the battery from being discharged

Do not use the power outlet longer than necessary when the engine is off.

■Appliances that may not operate properly (115 V)

The following 115 V appliances may not operate properly even if their power consumption is under 100 W. ●Appliances with high initial peak wattage ●Measuring devices that process precise data ●Other appliances that require an extremely stable power supply

299

3-7. Other interior features Grocery bag hook

This hook is designed to hang things like grocery bag.

Cabin

Press the hook.

Luggage compartment

300

3-7. Other interior features

NOTICE

■Grocery bag hook weight capacity

Cabin

Do not hang any object heavier than 44 lb. (20 kg) on the grocery bag hook.

Luggage compartment

Do not hang any object heavier than 7 lb. (3 kg) on the grocery bag hooks.

301

3-7. Other interior features Seatback table∗

Front passenger's seatback can be used as a temporary table only when the vehicle is stopped.

Fold down the front passen- ger's seat to use the seatback table. (→P. 38)

CAUTION

■Caution while driving

Observe the following precautions to avoid death or serious injury. ●Do not set up the seatback table. ●Do not sit on or place anything on the seatback table.

NOTICE

■To prevent damage to the seatback table

Do not put heavy loads on the table.

302

∗: If equipped

3-7. Other interior features Floor mat

Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet.

Fix the floor mat in place using the retaining hooks (clips) pro- vided.

The shape of the retaining hooks (clips) and the fixing procedure of the floor mat for your vehicle may differ from those shown in the illustration. For details, refer to the floor mat retention clip installation instructions supplied with the clips.

CAUTION

Observe the following precautions. Failure to do so may cause the driver's floor mat to slip, possibly interfering with the pedals while driving. An unexpectedly high speed may result or it may become difficult to stop the vehicle, leading to a serious accident. ■When installing the driver's floor mat

●Do not use floor mats designed for other models or different model year

vehicles, even if they are Toyota Genuine floor mats.

●Only use floor mats designed for the driver's seat. ●Always install the floor mat securely using the retaining hooks (clips) pro-

vided.

●Do not use two or more floor mats on top of each other. ●Do not place the floor mat bottom-side up or upside-down.

■Before driving

●Check that the floor mat is securely fixed in the right place with all the pro- vided retaining hooks (clips). Be espe- cially careful to perform this check after cleaning the floor.

●With the engine stopped and the shift lever in P (automatic transmission) or N (manual transmission), fully depress each pedal to the floor to make sure it does not interfere with the floor mat.

303

3-7. Other interior features Luggage compartment feature

■ Cargo hooks

Cargo hooks are provided for securing loose items.

■ Tie-down belts

To tighten To loosen To hook To unhook

304

■ Auxiliary boxes

3-7. Other interior features

knobs to Turn the “UNLOCK” position, remove the deck boards.

the and

305

3-7. Other interior features

■ Grocery bag hooks (→P. 300) ■ Tonneau cover (if equipped) STEP 1

Remove the deck board.

STEP 2

Take out the bag.

STEP 3

Remove the tonneau cover from the bag.

306

STEP 4

STEP 5

STEP 6

3-7. Other interior features

Slowly unfold cover.

the

tonneau

Attach the hook to the hook brackets.

Raise the rear center head restraint to attach the hook.

307

Hold the tonneau cover with both hands. Point your thumbs in opposite directions.

Bend one side of the cover towards you.

Twist the other side in the oppo- site direction, as shown in the illustration.

3-7. Other interior features

Folding the tonneau cover

STEP 1

STEP 2

STEP 3

308

STEP 4

STEP 5

3-7. Other interior features

Make a small circle, then fold it inward.

Make sure the three circles are side by side.

STEP 6

Put it in the bag.

309

3-7. Other interior features

CAUTION

■When unfolding the tonneau cover

Be careful not to hit yourself when unfolding the tonneau cover.

■Caution while driving

Keep the deck boards locked. Injuries may result in the event of an accident or sudden braking.

310

3-7. Other interior features Compass∗

The compass on the inside rear view mirror indicates the direction in which the vehicle is heading. ■ Operation

To turn the compass on or off, press and hold “AUTO” for 3
seconds.

■ Displays and directions

Display

NE SE SW NW

Direction

North

Northeast

East

Southeast

South

Southwest

West

Northwest

∗: If equipped 311

3-7. Other interior features

Calibrating the compass

The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle.

If you cross over a map boundary shown in the illustration, the compass will deviate. To obtain higher precision or perfect calibration, refer to the following.

■ Deviation calibration Stop the vehicle. STEP 1

STEP 2

Press and hold “AUTO” for 6
seconds.

A number (1 to 15) appears on the compass display.

STEP 3

Press “AUTO” and, referring to the map above, select the number of the zone where you are. If the direction is displayed several seconds after adjustment, the calibration is complete.

312

3-7. Other interior features

■ Circling calibration STEP 1

Stop the vehicle in a place where it is safe to drive in a circle. Press and hold “AUTO” for 9
seconds.

C appears on the compass dis- play.

Drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed.

STEP 2

STEP 3

If there is not enough space to drive in a circle, drive around the block until the direction is dis- played.

■Conditions unfavorable for correct operation

The compass may not show the correct direction in the following situations: ●The vehicle is stopped immediately after turning. ●The vehicle is on an inclined surface. ●The vehicle is in a place where the earth's magnetic field is subject to interference by artificial magnetic fields (underground car park/parking lot, under a steel tower, between buildings, roof car park/parking lot, near an intersection, near a large vehicle, etc.).

●The vehicle has become magnetized.

(There is a magnet or metal object near the anti-glare inside rear view mirror.)

●The battery has been disconnected. ●A door is open.

313

3-7. Other interior features

CAUTION

■While driving the vehicle

Do not adjust the display. Be sure to adjust the display only when the vehicle is stopped.

■When doing the circling calibration

Be sure to secure a wide space, and watch out for people and vehicles in the neighborhood. Do not violate any local traffic rules while performing circling calibration.

NOTICE

■To avoid compass malfunctions

Do not place magnets or any metal objects near the anti-glare inside rear view mirror. Doing this may cause a malfunction of the compass sensor.

■To ensure normal operation of the compass

●Do not perform circling calibration of the compass in a place where the earth's magnetic field is subject to interference by artificial magnetic fields. ●During calibration, do not operate electric systems (moon roof, power win-

dows, etc.) as they may interfere with the calibration.

314

4-1. Maintenance and care Cleaning and protecting the vehicle exterior

Perform the following to protect the vehicle and maintain it in prime condition.

● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust. Wash the vehicle body using a sponge or soft cloth, such as a chamois.

● For hard-to-remove marks, use car wash soap and rinse thor-

oughly with water.

● Wipe away any water. ● Wax the vehicle when the waterproof coating deteriorates. If water does not bead on a clean surface, apply wax when the vehicle body is cool.

■Automatic car washes

●Before washing the vehicle, do the following.

• Fold the mirrors back. • Remove the antenna.

●Brushes used in automatic car washes may scratch the vehicle surface

and harm your vehicle's paint.

■High pressure car washes

●Do not allow the nozzles of the car wash to come within close proximity

of the windows.

●Before car wash, check that the fuel filler door on your vehicle is closed

properly.

316

4-1. Maintenance and care

■Aluminum wheels

●Remove any dirt immediately by using a neutral detergent. Do not use hard brushes or abrasive cleaners. Do not use strong or harsh chemical cleaners. Use the same mild detergent and wax as used on the paint.

●Do not use detergent on the wheels when they are hot, for example after

driving for long distance in the hot weather.

●Wash detergent from the wheels immediately after use.

■Bumpers

Do not scrub with abrasive cleaners.

CAUTION

■Caution about the exhaust pipe

Exhaust gasses cause the exhaust pipe to become quite hot. When washing the vehicle, be careful not to touch the pipe until it has cooled sufficiently, as touching a hot exhaust pipe can cause burns.

317

4-1. Maintenance and care

NOTICE

■To prevent paint deterioration and corrosion on the body and compo-

nents (aluminum wheels etc.) ●Wash the vehicle immediately in the following cases:

• After driving near the sea coast • After driving on salted roads • If you see coal tar or tree sap on the paint surface • If you see dead insects or insect droppings on the paint • After driving in an area contaminated with soot, oily smoke, mine dust,

iron powder or chemical substances

• If the vehicle becomes heavily soiled in dust or mud • If liquids such as benzene and gasoline are spilled on the paint surface

●If the paint is chipped or scratched, have it repaired immediately. ●To prevent the wheels from corroding, remove any dirt and store in a place

with low humidity when storing the wheels.

■If the windshield washer nozzle become blocked

Contact your Toyota dealer. Do not try to clear it with a pin or other object. This may damage the nozzle. ■Cleaning the exterior lights

●Wash carefully. Do not use organic substances or scrub with a hard brush.

This may damage the surfaces of the lights.

●Do not apply wax on the surfaces of the lights.

Wax may cause damage to the lenses.

■Antenna installation and removal precautions

●Before driving, ensure that the antenna is installed. ●When the antenna is removed, such as before entering an automatic car wash, make sure to store it in a suitable place so as not to lose it. Also, before driving, make sure to reinstall the antenna in its original position.

318

4-1. Maintenance and care Cleaning and protecting the vehicle interior

The following procedures will help protect your vehicle's interior and keep it in top condition: ■ Protecting the vehicle interior

Remove dirt and dust using a vacuum cleaner. Wipe dirty sur- faces with a cloth dampened with lukewarm water.

■ Cleaning the leather areas

● Remove dirt and dust using a vacuum cleaner. ● Wipe any excess dirt and dust with a soft cloth dampened with

diluted detergent. Use a diluted water solution of approximately 5% neutral wool deter- gent.

● Wring out any excess water from the cloth and thoroughly

wipe off all remaining traces of detergent.

● Wipe the surface with a dry, soft cloth to remove any remain- ing moisture. Allow the leather to dry in a shaded ventilated area.

■ Synthetic leather areas

● Remove loose dirt using a vacuum cleaner. ● Apply a mild soap solution to the synthetic leather using a

sponge or soft cloth.

● Allow the solution to soak in for a few minutes. Remove the

dirt and wipe off the solution with a clean, damp cloth.

319

4-1. Maintenance and care

■Caring for leather areas

Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior.

■Shampooing the carpets

There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam. Rub in overlapping circles. Do not apply water. Excellent results are obtained by keeping the carpet as dry as possi- ble.

■Seat belts

Clean with mild soap and lukewarm water using a cloth or sponge. Also check the belts periodically for excessive wear, fraying or cuts.

CAUTION

■Water in the vehicle

●Do not splash or spill liquid in the vehicle. Doing so may cause electrical

components etc. to malfunction or catch fire.

●Do not get any of the SRS components or wiring in the vehicle interior wet.

(→P. 72) Electrical malfunction may cause the airbags to deploy or not function properly, resulting in death or severe injury.

■Cleaning the interior (especially instrument panel)

Do not use polish wax or polish cleaner. The instrument panel may reflect off the windshield, obstructing the driver's view and leading to an accident, resulting in death or serious injury.

320

4-1. Maintenance and care

NOTICE

■Cleaning detergents

●Do not use organic substances such as benzene or gasoline, acidic or alkaline solutions, dye, bleach or other detergent. Doing so may discolor the vehicle interior or cause streaks or damage to painted surfaces.

●Do not use polish wax or polish cleaner. The instrument panel's or other

interior part's painted surface may be damaged.

■Preventing damage to leather surfaces

Observe the following precautions to avoid damage to and deterioration of leather surfaces. ●Remove any dust or dirt on leather surfaces immediately. ●Do not expose the vehicle to direct sunlight for extended periods of time.

Park the vehicle in the shade, especially during summer.

●Do not place items made of vinyl, plastic, or that contain wax, on the upholstery, as they may stick to the leather surface if the vehicle interior heats up significantly.

■Water on the floor

Do not wash the vehicle floor with water. Vehicle systems such as the audio system may be damaged if water comes into contact with electrical components under the floor of the vehicle, and may also cause the body to rust.

■Cleaning the inside of the rear window

●Do not use glass cleaner to clean the rear window, as this may cause damage to the rear window defogger heater wires. Use a cloth dampened with lukewarm water to gently wipe the window clean. Wipe the window in strokes running parallel to the heater wires.

●Be careful not to scratch or damage the heater wires.

321

4-2. Maintenance Maintenance requirements

To ensure safe and economical driving, day-to-day care and regular maintenance is essential. It is the owner’s responsibility to perform regular checks. Toyota recommends the following maintenance. ■ General maintenance

Should be performed on a daily basis. This can be done by your- self or by a Toyota dealer. ■ Scheduled maintenance

Should be performed at specified intervals according to the maintenance schedule. For details about maintenance items and schedules, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

■ Do-it-yourself maintenance

You can perform some maintenance procedures yourself. Please be aware that do-it-yourself maintenance may affect war- ranty coverage. The use of Toyota Repair Manuals is recommended. For details about warranty coverage, see the separate “Owner’s War- ranty Information Booklet” or “Owner’s Manual Supplement”.

322

4-2. Maintenance

■Repair and replacement

It is recommended that genuine Toyota parts be used for repair to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.

■After changing the engine oil (U.S.A. only)

After the requred maintenace is performed according to the maintenance schedule, please reset the maintenance data. To reset the data, follow the procedures described below: STEP 1

Turn the engine switch OFF with the trip meter A reading shown. While pressing the trip meter reset button (→P. 129), turn the engine switch to the “ON” position. Continue to press and hold the button until the trip meter displays 000000.

STEP 2

STEP 3

■Allow inspection and repairs to be performed by a Toyota dealer

●Toyota technicians are well-trained specialists and are kept up to date with the latest service information. They are well informed about the operations of all systems on your vehicle.

●Keep a copy of the repair order. It proves that the maintenance that has been performed is under warranty coverage. If any problem should arise while your vehicle is under warranty, your Toyota dealer will promptly take care of it.

323

4-2. Maintenance

CAUTION

■Warning in handling of battery

●Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm. Work in a well ventilated area.

●Oils, fuels and fluids contained in vehicles as well as waste produced by component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Avoid exposure and wash any affected area immediately.

●Battery posts, terminals and related accessories contain lead and lead compounds which are known to cause brain damage. Wash your hands after handling. (→P. 347)

324

4-2. Maintenance

General maintenance

Listed below are the general maintenance items that should be per- formed at the intervals specified in the “Owner's Warranty Informa- tion Booklet” or “Owner’s Manual Supplement/Scheduled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice.

Engine compartment

Items

Battery

Brake fluid Engine coolant Engine oil Exhaust system

Radiator/condenser/hoses

Washer fluid

Check points Check the connections.

(→P. 347) At the correct level? (→P. 345) At the correct level? (→P. 343) At the correct level? (→P. 339) No fumes or strange sounds? Not blocked with foreign matter?

(→P. 344) At the correct level? (→P. 349)

325

4-2. Maintenance

Vehicle interior

Items

Check points

Accelerator pedal

Automatic transmission “Park” mechanism

Brake pedal

Brakes

Clutch pedal

Head restraints

Indicators/buzzers Lights

Parking brake

Seat belts

Seats

Steering wheel

326

• Moves smoothly (without uneven pedal effort or catching)? • Can the vehicle be held securely on an incline with the shift lever in P? • Moves smoothly? • Does it have appropriate clear- ance and correct amount of free play? • Not pull to one side when applied? • Loss of brake effectiveness? • Spongy feeling brake pedal? • Pedal almost touches floor? • Moves smoothly? • Move smoothly and lock securely? • Function properly? • Do all the lights come on? • Moves smoothly? • Can hold the vehicle securely on an incline? • Does the seat belt system oper- ate smoothly? • Are the belts undamaged? • Do the seat controls operate properly? • Moves smoothly? • Has correct free play? • No strange noises?

4-2. Maintenance

Vehicle exterior

Items

Check points

Doors Engine hood

Fluid leaks

Tires

• Operate smoothly? • The lock system works properly? • Is there any leakage after park- ing? • Inflation pressure is correct? • Tire surfaces not worn or dam- aged? • Tires rotated according to the maintenance schedule? • Wheel nuts are not loose?

CAUTION

■If the engine is running

Turn the engine off and ensure that there is adequate ventilation before per- forming maintenance checks.

327

4-2. Maintenance

Emission inspection and maintenance (I/M) programs

Some states have vehicle emission inspection programs which include OBD (On Board Diagnostics) checks. The OBD system moni- tors the operation of the emission control system. ■ If the malfunction indicator lamp comes on

The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/ M test and may need to be repaired. Contact your Toyota dealer to service the vehicle.

■ Your vehicle may not pass the I/M test:

● When the battery is disconnected or discharged

Readiness codes that are set during ordinary driving are erased. Also, depending on your driving habits, the readiness codes may not be completely set.

● When the fuel tank cap is loose

The malfunction indicator lamp comes on as a temporary mal- function and your vehicle may not pass the I/M test.

■ When the malfunction indicator lamp goes off after several

driving trips The error code in the OBD system will not be cleared unless the vehicle is driven 40 or more times.

■ If your vehicle does not pass the I/M test

Contact your Toyota dealer to prepare the vehicle for re-testing.

328

4-3. Do-it-yourself maintenance Do-it-yourself service precautions

If you perform maintenance yourself, be sure to follow the correct procedures as given in these sections.

Items

Parts and tools

• Warm water • Baking soda • Grease • Conventional wrench (for terminal clamp bolts) • FMVSS No.116 DOT 3 or SAE J1703 brake fluid • Rag or paper towel • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non-silicate, non- amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology. For the U.S.A.: “Toyota Super Long Life Coolant” is pre-mixed with 50% coolant and 50% deionized water. For Canada: “Toyota Super Long Life Coolant” is pre-mixed with 55% coolant and 45% deionized water. • Funnel (used only for adding engine coolant) • “Toyota Genuine Motor Oil” or equivalent • Rag or paper towel, funnel (used only for adding oil)

Battery condition

(→P. 347)

Brake fluid level

(→P. 345)

Engine coolant level

(→P. 343)

Engine oil level

(→P. 339)

328

4-3. Do-it-yourself maintenance

Items

Parts and tools

Fuses

(→P. 371)

• Fuse with same amperage rating as original

Radiator and condenser

(→P. 344)

Tire inflation pressure (→P. 360)

Washer fluid

(→P. 349)

⎯

• Tire pressure gauge • Compressed air source • Water washer fluid containing antifreeze (for winter use) • Funnel

329

4-3. Do-it-yourself maintenance

CAUTION

The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury observe the following precautions. ■When working on the engine compartment

●Keep hands, clothing, and tools away from the moving fan and engine

drive belt.

●Be careful not to touch the engine, radiator, exhaust manifold, etc. right

after driving as they may be hot. Oil and other fluids may also be hot.

●Do not leave anything that may burn easily, such as paper or rags, in the

engine compartment.

●Do not smoke, cause sparks or expose an open flame to fuel or the bat-

tery. Fuel and battery fumes are flammable.

●Be extremely cautious when working on the battery. It contains poisonous

and corrosive sulfuric acid.

●Take care because brake fluid can harm your hands or eyes and damage

painted surfaces. If fluid gets on your hands or in your eyes, flush the affected area with clean water immediately. If you still experience discomfort, see a doctor.

■When working near the electric cooling fans or radiator grille

Be sure the engine switch is OFF. With the engine switch in the “ON” posi- tion, the electric cooling fans may automatically start to run if the air condi- tioning is on and/or the coolant temperature is high. (→P. 344)

■Safety glasses

Wear safety glasses to prevent flying or falling material, fluid spray, etc. from getting in the eyes.

330

4-3. Do-it-yourself maintenance

NOTICE

■If you remove the air cleaner

Driving with the air cleaner removed may cause excessive engine wear due to dirt in the air. Also, a backfire could cause a fire in the engine compart- ment.

331

4-3. Do-it-yourself maintenance Hood

Release the lock from the inside of the vehicle to open the hood.

Pull the hood release lever. The hood will pop up slightly.

Lift the auxiliary catch lever and lift the hood.

Hold the hood open by insert- ing the supporting rod into the slot.

STEP 1

STEP 2

STEP 3

332

4-3. Do-it-yourself maintenance

CAUTION

■Pre-driving check

Check that the hood is fully closed and locked. If the hood is not locked properly, it may open while the vehicle is in motion and cause an accident, which may result in death or serious injury.

■After installing the support rod into the slot

Make sure the rod supports the hood securely from falling down on to your head or body.

NOTICE

■When closing the hood

Be sure to return the support rod to its clip before closing the hood. Closing the hood with the support rod up could cause the hood to bend.

333

4-3. Do-it-yourself maintenance Positioning a floor jack

When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury. ■ Front

1.8 L 4-cylinder (2ZR-FE) engine

2.4 L 4-cylinder (2AZ-FE) engine

334

4-3. Do-it-yourself maintenance

■ Rear

2WD models without 18-inch tires

2WD models with 18-inch tires

AWD models

335

4-3. Do-it-yourself maintenance

CAUTION

■When raising your vehicle

Make sure to observe the following to reduce the possibility of death or seri- ous injury.

●Lift up the vehicle using a floor jack such as the one shown in the illustra- tion.

●When using a floor jack, follow the instructions of the manual provided with

the jack.

●Do not use the jack that was supplied with your vehicle. ●Do not put any part of your body or get underneath the vehicle supported

only by the floor jack.

●Always use floor jack and/or automotive jack stands on a solid, flat, level

surface.

●Do not start the engine while the vehicle is supported by the floor jack. ●Stop the vehicle on level firm ground, firmly set the parking brake and put

the shift lever in P (automatic transmission) or R (manual transmission).

●Make sure to set the floor jack properly at the jack point.

Raising the vehicle with an improperly positioned floor jack will damage the vehicle and may cause the vehicle to fall off the floor jack.

●Do not raise the vehicle while someone is in the vehicle. ●When raising the vehicle, do not place any objects on top of or underneath

the floor jack.

336

4-3. Do-it-yourself maintenance Engine compartment

1.8 L 4-cylinder (2ZR-FE) engine

Engine oil filler cap

(→P. 340)

Engine oil level dipstick

(→P. 339)

Brake fluid reservoir

Fuse box

(→P. 345) (→P. 371)

(→P. 347) (→P. 344)

Battery Radiator Electric cooling fan Condenser Engine coolant reservoir

(→P. 344)

(→P. 343) Washer fluid tank (→P. 349)

337

4-3. Do-it-yourself maintenance

2.4 L 4-cylinder (2AZ-FE) engine

Engine coolant reservoir

(→P. 343)

Engine oil filler cap

(→P. 340)

Engine oil level dipstick

(→P. 339)

Brake fluid reservoir

(→P. 345)

(→P. 371) (→P. 347) (→P. 344)

Fuse box Battery Radiator Electric cooling fans (→P. 344) Condenser Washer fluid tank (→P. 349)

338

4-3. Do-it-yourself maintenance

Engine oil

With the engine at operating temperature and turned off, check the oil level on the dipstick. ■ Checking the engine oil STEP 1

Park the vehicle on level ground. After turning off the engine, wait more than five minutes for the oil to drain back into the bottom of the engine.

STEP 2

Hold a rag under the end and pull the dipstick out.

STEP 3

STEP 4

STEP 5

STEP 6

Wipe the dipstick clean. Reinsert the dipstick fully. Holding a rag under the end, pull the dipstick out and check the oil level. Wipe the dipstick and reinsert it fully.

1.8 L 4-cylinder (2ZR-FE) engine

Low Full

339

4-3. Do-it-yourself maintenance

2.4 L 4-cylinder (2AZ-FE) engine

Low Full

■ Adding engine oil

If the oil level is below or near the low level mark, add engine oil of the same type as already in the engine.

Make sure to check the oil type and prepare the items needed before adding oil.

Engine oil selection →P. 447

Oil quantity (Low → Full)

Items

1.8 L 4-cylinder (2ZR-FE) engine

1.6 qt. (1.5 L, 1.3 Imp. qt.)

2.4 L 4-cylinder (2AZ-FE) engine

1.1 qt. (1.0 L, 0.9 Imp. qt.) Clean funnel

STEP 1

STEP 2

STEP 3

Remove the oil filler cap. Add engine oil slowly, checking the dipstick. Install the filler cap, turning it clockwise.

340

4-3. Do-it-yourself maintenance

■Engine oil consumption