2004 Toyota Highlander Owners Manual

D If the seat belt does not function it cannot protect your normally, child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

’04 HIGHLANDER_U (L/O 0308)

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

95

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the convertible seat, press the buckle release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat must be used in for- ward−facing position only.

96

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Same angle

Same position

D On vehicles with side airbags and curtain shield airbags, do not allow the child to lean his/her head or any part of his/her body against the door or the area of the seat, front or rear pillar or roof side rail from which the side airbags or curtain shield airbags deploy even if the child is seated in the child restraint system. It is dangerous if the side airbag and curtain shield airbag in- flate, and the impact could cause death or serious injury to the child.

D When

installing a child restraint system in the second seat center position, adjust both seat cushions to the same position and align both seatbacks at the same angle. Other- wise, the child restraint system can- not be securely restrained and this may cause death or serious injuries in a collision.

97

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

Move seat fully back

CAUTION

the

D A forward−facing child restraint sys- to be tem should be allowed front passenger installed on seat only when it is unavoidable. Always move the seat as far back as possible even if the “AIRBAG OFF” indicator light is illuminated, because the front passenger airbag considerable could speed and the child may be killed or seriously in- jured.

force. Otherwise,

inflate with

’04 HIGHLANDER_U (L/O 0308)

CAUTION

D Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Otherwise, the child may be killed or seriously injured in case of sud- den braking or a collision.

D If the seat belt does not function normally, it cannot protect your child from death or serious injury. Contact your Toyota dealer immedi- ately. Do not the child restraint system on the seat until the seat belt is fixed.

install

could

D Both high−positioned lap belts and cause loose−fitting belts death or serious to sliding under the lap belt during a collision or other unintended event. Keep the lap belt positioned as low on a child’s hips as possible.

injuries due

D For child’s safety, do not place the

shoulder belt under child’s arm.

D After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

D Do not insert coins, clips, etc. in the buckle as this may prevent your child from properly latching the tab and buckle.

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and across the child following the instructions provided by its manufacturer and insert the tab into the buckle taking care not to twist the belt.

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” on page 54 in this Section for details.

98

’04 HIGHLANDER_U (L/O 0308)

—Using a top strap

Anchor brackets

Symbol

2. To remove the child restraint system, the buckle release button and

press allow the belt to retract.

Follow the procedure below for a child restraint system that requires the use of a top strap.

to secure

Use the anchor brackets behind the sec- ond seat seatbacks top strap. Anchor brackets are seating position of the second seat. This symbol the user ready anchor brackets.

locations of

indicates

for each

installed

the

99

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

TO USE THE ANCHOR BRACKET: 1. Remove the head restraint.

2. Open the anchor bracket cover with the symbol as shown in the illustra- tion.

3. Fix the child restraint system with

the seat belt. Latch bracket and tighten the top strap.

the hook onto

the anchor

instructions

For the child re- straint system, see “Child restraint” on page 85 in this Section.

install

to

100

CAUTION

Make sure the top strap is securely latched, and check that the child re- straint system is secure by pushing and pulling it in different directions. Follow all the installation instructions provided by its manufacturer.

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

—Installation with child restraint lower anchorages

4. Replace the head restraint and lift it

up to the uppermost lock position.

Be sure to close the cover when the an- chor bracket is not in use.

specifications

Lower anchorages for the child restraint systems complying with the FMVSS225
or CMVSS210.2 are installed in the second seat. The anchorages are installed in the seat cushion of both outside second seats. Child restraint systems complying with the FMVSS225 or CMVSS210.2 specification can be fixed to these anchorages. In this case, it is not necessary to fix the child restraint system with a seat belt on the vehicle.

Canada only

Type A

101

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

RESTRAINT

For owners in Canada The symbol on a child restraint system indicates the presence of a lower connec- tor system. CHILD INSTALLATION Type A— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages below the tag in the seatback.

SYSTEM

2. Latch the hooks of lower straps onto the anchorages and tighten the lower straps. Type B— 1. Widen

the the clearance between seat cushion and seatback a little and confirm the position of the low- er anchorages below the tag in the seatback.

2. Latch the buckles onto the anchor-

ages.

it should be anchored. (For

If your child restraint system has a top strap, the installation of the top strap, see “—Using a top strap” on page 99 in this Section.)

Canada only

Type B

102

the installation details, refer

For to the instruction manual equipped with each product.

CAUTION

D When using the lower anchorages for the child restraint system, be sure that there are no irregular ob- jects around the anchorages or that the seat belt is not caught.

D Push and pull the child restraint system in different directions to be sure is secure. Follow all the installation instructions provided by its manufacturer.

it

D When using the lower anchorages for the child restraint system, en- sure that the seat is moved to the rear−most position, with the seat- back close to the child restraint system.

D After securing

the child restraint system, never slide or recline the seat.

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

D Do not install a child restraint sys- tem on the second seat if it inter- feres with the lock mechanism of the front seats. Otherwise, the child or front seat occupant(s) may be killed or seriously injured in case of sudden braking or a collision.

103

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

104

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

SECTION 1− 4

OPERATION OF INSTRUMENTS AND CONTROLS Steering wheel and Mirrors Tilt steering wheel Outside rear view mirrors Anti−glare inside rear view mirror Auto anti−glare inside rear view mirror Sun visors

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

106
106
108
109
110

105

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Tilt steering wheel

Outside rear view mirrors—

CAUTION

D Do not adjust the steering wheel while the vehicle is moving. Doing so may cause the driver to mishan- dle the vehicle and an accident may occur resulting in death or serious injuries.

D After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

To change the steering wheel angle, hold the steering wheel, push down the lock the steering wheel to the desired angle and return the lever to its original position.

release

lever,

tilt

106

Adjust the mirror so that you can just see the side of your vehicle in the mir- ror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side because it is a convex mirror. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror. On some models, when you push the out- side rear view mirror defogger switch, the heater panels the outside rear view mirrors will quickly clear the mirror sur- face. (See “Rear window and outside rear view mirror defoggers and windshield wip- er de−icer” on page 122 in Section 1−5.)

in

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

—Power rear view mirror control

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de−icer to free the mirror.

CAUTION

D Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the vehicle and an accident may occur resulting in death or serious inju- ries.

D Since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Push (right).

the switch to “L” (left) or “R”

2. Control switch—To move the mirror

Push the switch in the desired direc- tion.

Mirrors can be adjusted when the key is in the “ACC” or “ON” position.

107

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

—Folding rear view mirrors

Anti−glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

The rear view mirrors can be folded backward for parking in compact areas. To fold the rear view mirror, push back- ward.

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

108

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Auto anti−glare inside rear view mirror

Type A

Type B

When the inside air temperature is low, it for the mirror to may take little longer darken to the detection of headlights.

in response

CAUTION

Do not adjust the mirror while the vehicle is moving. Doing so may cause the driver to mishandle the ve- hicle and an accident may occur re- sulting in death or serious injuries.

is

the

ignition key

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. This mirror is equipped with auto anti− glare function. The function is designed to reduce glare from the headlights of the vehicle behind you during night driving. When inserted and turned on, the inside rear view mirror al- ways turns on in the automatic function mode. The indicator illuminates to show you that the function is on. In automatic function mode, if the mirror detects light from the headlights of the vehicle behind you, the mirror surface darkens slightly the reflected light. To turn off the automatic function: Type A—Push the “OFF” switch. Type B—Push the “MIRROR” switch. To turn on the automatic function again: Type A—Push the “AUTO” switch. Type B—Push the “MIRROR” switch. Adjust it before driving so that the rear view is in the best condition.

to reduce

109

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Sun visors—

To ensure correct functioning of an anti−glare mirror sensor located on the back side of the mirror, do not touch or cover the sensor with your finger or a piece of cloth, etc.

Type A

Type B

110

To block out glare, move the sun visor. To block out glare from the front—Swing down the sun visor (position 1). To block out glare from the side—Swing down the sun visor, remove it from the hook and swing it to the lateral side (posi- tion 2). If glare comes from obliquely behind you, extend the plate at the end of the visor (position 3).

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

CAUTION

Do not extend the plate at the end of the sun visor when the visor is in the position 1. It can cover the anti−glare inside rear view mirror and obstruct the rear view.

—Vanity mirrors

To use the vanity mirrors, swing down the main sun visor and slide the cover. Type A only—The vanity light comes on when you slide the cover.

Type A

Type B

111

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

112

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

SECTION 1− 5

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior lights Personal lights Ignition switch light Windshield wipers and washer Rear window wiper and washer Rear window and outside rear view mirror defoggers and windshield

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

114
117
117
118
118
119
120
121
122

wiper de−icer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

122

113

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Headlights and turn signals (with automatic light control system)

top of

the driver’s side

The automatic light control sensor is on the instrument panel. Do not place anything on the instrument panel, and/or do not affix anything on the windshield to block this sensor.

The lights automatically turn off when the driver’s door is opened with the ignition key in the “ACC” or “LOCK” position. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

the

Daytime running light system (on some models) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above Position 3 (“AUTO”)—Headlights and/or all of the lights in position 1
They automatically turn on or off depend- ing on the darkness of the surroundings. Manually twist the knob to the position 2
to turn on the headlights if they are need- ed immediately when entering a dark tun- nel, parking structure, etc.

the

114

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Headlights and turn signals (without automatic light control system)

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 392 in Section 7−3.

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above The lights automatically turn off when the driver’s door is opened with the ignition turned off. To turn them on again, turn the key to the “ON” position or actuate the headlight switch. If you are going to park for over one week, make sure the head- light switch is off.

the

115

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

the

Daytime running light system (on some models) The headlights turn on at reduced intensi- ty when the parking brake is released with the engine started, even with light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Twist the knob to the position 2 to turn the headlights to full intensity for driving at night.

116

High−Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out. See “Replacing light bulbs” on page 392 in Section 7−3.

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Emergency flashers

Instrument panel light control

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

To adjust the brightness of the instru- ment panel lights, turn the knob.

117

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Front fog lights

Interior lights

ILLUMINATED ENTRY SYSTEM (center interior light) When the switch is in the “DOOR” posi- tion and any of the side doors and back door is opened, the light will come on. After all the side doors and back door are closed, the light remains on for about 15
seconds before fading out. However, in the following cases, the light fades out immediately: D All the side doors and back door are in

ignition key

closed when “ACC” or “ON” position.

the

is

To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.

To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”— Center: Turns the light on when any of the side doors and back door are opened. Rear: Turns the light on when the back door is opened.

D The ignition key is turned to “ACC” or “ON” after all the side doors and back door are closed.

D All the side doors and back door are

locked when the light is still on.

When all the side doors and back door are unlocked using either the key or the wireless remote control transmitter simul- taneously, the light will come on and re- main on for about 15 seconds before fad- ing out.

118

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

The following adjustments can be made in this system. For details, contact your Toyota dealer. D Cancelling the door key or wireless re- mote control transmitter linked opera- tion

D Changing the timing for the light turn-

ing off

Personal lights

With moon roof

Without moon roof

’04 HIGHLANDER_U (L/O 0308)

The personal lights operate separately with each lens. To turn on the light, push the lens on your side. To turn the light off, push the switch once again. The center switch has the following posi- tions: “DOOR”—Turns the lights on when any of the side doors or back door is opened. “OFF”—The lights are off. ILLUMINATED ENTRY SYSTEM When the switch is in the “DOOR” posi- tion and any of the side doors and back door is opened, the light will come on. After all the side doors and back door are closed, the light remains on for about 15
seconds before fading out. However, in the following cases, the light fades out immediately: D All the side doors and back door are in

ignition key

closed when “ACC” or “ON” position.

the

is

D The ignition key is turned to “ACC” or “ON” after all the side doors and back door are closed.

D All the side doors and back door are

locked when the light is still on.

119

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

When all the side doors and back door are unlocked using either the key or the wireless remote control transmitter simul- taneously, the light will come on and re- main on for about 15 seconds before fad- ing out. The following adjustments can be made in this system. For details, contact your Toyota dealer. D Cancelling the door key or wireless re- mote control transmitter linked opera- tion

D Changing the timing for the light turn-

ing off

’04 HIGHLANDER_U (L/O 0308)

Ignition switch light

D All the side doors and back door are closed and locked when the light is still on.

When all the side doors and back door are unlocked using either the key or the wireless remote control transmitter simul- taneously, the light will come on and re- main on for about 15 seconds before fad- ing out. The following adjustments can be made in this system. For details, contact your Toyota dealer. D Cancelling the door key or wireless re- mote control transmitter linked opera- tion

D Changing the timing for the light turn-

ing off

For easy access to the ignition switch, the ignition switch light comes on when any of the side doors are opened. The light remains on for some time after all the side doors and back door are closed. However, in the following cases, the lights go off immediately. D All the side doors and back door are in

ignition key

closed when “ACC” or “ON” position.

the

is

D The ignition key is turned to “ACC” or “ON” after all the side doors and back door are closed.

120

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

When waxing your vehicle, make sure that the washer nozzles do not become blocked. If a nozzle becomes blocked, contact your Toyota dealer to have the vehicle serviced.

NOTICE

If a nozzle becomes blocked, do not try to clear it with a pin or other object. The nozzle will be damaged.

the band upward to

The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it. To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” on page 391 in Section 7−3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield the glass.

It may scratch

is dry.

Windshield wipers and washer

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Position 3

Intermittent

Slow

Fast

For a single sweep of push the lever up and release it.

the windshield,

121

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Rear window wiper and washer

Rear window and outside rear view mirror defoggers and windshield wiper de−icer

NOTICE

Do not operate the rear wiper if the rear window is dry. It may scratch the glass.

To turn on the rear window wiper, twist the lever knob upward. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Intermittent

Normal

To squirt washer fluid on the rear window, twist the knob upward or downward as far as it will go (position 3 or 4). The knob automatically returns from these positions after you release it. For instructions on adding washer fluid, see “Adding washer fluid” on page 391 in Section 7−3.

122

Without navigation system (type A)

Without navigation system (type B)

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

On some models, the outside rear view mirror defoggers and/or the windshield wiper de−icer is also operating simulta- neously by this switch. Vehicles with the outside rear view mirror defoggers, the heater panel in the outside rear view mir- rors will quickly clear the surfaces. Ve- hicles with the windshield wiper de−icer, the windshield wiper blades will be de− iced. Push the switch once again to turn the defoggers off. The system will automatically shut off af- ter the defogger has operated about 15
minutes.

CAUTION

Vehicles with outside rear view mirror defoggers, since the mirror surfaces can get hot, do not touch them when the defogger switch is on.

turn

Make sure you the defoggers off when the surfaces are clear or the wiper blades have de−iced. Leaving the defog- gers on for a long time could cause the battery to discharge, especially during stop−and−go driving. The defoggers are not designed for drying rain water or for melting snow. If the outside rear view mirrors are heavi- ly coated with ice, use a spray de−icer before operating the switch.

NOTICE

When cleaning the inside of the rear window, be careful not to scratch or damage the heater wires or connec- tors.

With navigation system

To defog or defrost the rear window, push the switch. The key must be in the “ON” position. The thin heater wires on the inside of the rear window will quickly clear the window surface. An indicator light will illuminate to indicate the defogger is operating.

123

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

124

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

SECTION 1− 6

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fuel gauge Engine coolant temperature gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tachometer Odometer and two trip meters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Service reminder indicators and warning buzzers

126
126
127
127
129

125

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Fuel gauge

Engine coolant temperature gauge

Low fuel level warning light

On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual. If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

indicates

The gauge the approximate quantity of the fuel remaining in the tank when the ignition switch is on. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. The needle moves when braking, acceler- ating or making turns. This is caused by the movement of the fuel in the tank. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible.

126

The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle overheats, stop your vehicle and allow the engine to cool. Your vehicle may overheat during severe operating conditions, such as: D Driving up a long hill on a hot day. D Reducing speed or stopping after high

speed driving.

D Idling for a long period with the air conditioning on in stop−and−go traffic.

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Tachometer

Odometer and two trip meters

D Towing a trailer.

NOTICE

z Do not remove the thermostat

in the engine cooling system as this may cause the engine to overheat. The thermostat is designed to con- trol the flow of coolant to keep the temperature of the engine within the specified operating range.

z Do not continue driving with an overheated engine. See “If your ve- hicle overheats” on page 328 in Section 4.

The tachometer indicates engine speed in thousands of rpm (revolutions per minute). Use it while driving to select correct shift points and to prevent en- gine lugging and over−revving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy. Remember, in most cases the slower the engine speed, the greater the fuel economy.

NOTICE

Do not let the indicator needle get into the red zone. This may cause severe engine damage.

This meter displays the odometer and two trip meters. 1. Odometer—Shows

total distance

the

the vehicle has been driven.

2. Two

trip meters—Show

two different distances independently driven since the last time each trip meter was set to zero. You can use one trip meter to calculate the to measure the distance on each trip. All trip meter data is cancelled if the elec- trical power source is disconnected.

fuel economy and

the other

127

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

3. Trip meter reset knob—Resets the two trip meters to zero, and also change the meter display. To change the meter display, quickly push and release the knob. The meter display changes in the order from the odometer to trip meter A to trip meter then back B, the odometer each time you push. To reset the trip meter A to zero, dis- play the meter A reading, then push and hold the knob until the meter is set to zero. The same process can be applied for resetting the trip meter B.

to

128

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Service reminder indicators and warning buzzers

If the indicator or buzzer comes on...

Do this.

(a)

(b)

(c)

(d)

(e)

(f)

(g)

or

(indicator and buzzer)

If parking brake is off, stop immediately and contact Toyota dealer.

(indicator and buzzer)

Fasten driver’s seat belt.

Fasten front passenger’s seat belt.

Stop and check.

Stop and check.

or

Take vehicle to Toyota dealer.

Low fuel level warning light

Fill up tank.

129

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

If the indicator or buzzer comes on...

Do this.

or

Take vehicle to Toyota dealer. If brake system warning light is also on, stop immediately and contact Toyota dealer.

(indicator and buzzer)

Close all side doors and back door.

Stop and check.

Take vehicle to Toyota dealer immediately.

Take vehicle to Toyota dealer.

Adjust tire inflation pressure. If light remains, contact Toyota dealer.

Add washer fluid.

(h)

(i)

(j)

(k)

(l)

(m)

(n)

130

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

If the indicator or buzzer comes on...

Do this.

(o)

(p)

Replace engine oil.

Key reminder buzzer

Remove key.

131

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

(a) Brake System Warning Light and

Buzzer

A warning light turning on briefly during operation does not indicate a problem.

(b) Driver’s Seat Belt Reminder Light

and Buzzer

the

This light comes on in the following cases when the ignition key is in the “ON” posi- tion. D When the parking brake is applied... This light comes on for a few seconds when to the “ON” position even after the parking brake is released. If the vehicles speed rises above 5 km/h (3 mph) with the parking brake applied, a buzzer sounds. D When the brake fluid level is low...

ignition key

turned

is

CAUTION

It is dangerous to continue driving normally when the brake fluid level is low.

Have your vehicle checked at your Toyota dealer in the following cases: D The light does not come on even if the parking brake is applied when the igni- tion key is in the “ON” position.

D The light does not come on even if the ignition key is turned on with the park- ing brake released.

132

CAUTION

If either of the following conditions occurs, immediately stop your vehicle at a safe place and contact your Toyota dealer. D The

light does not turn off even after the parking brake is released while the engine is running. In this case, the brakes may not work properly and your stopping distance will become longer. De- press the brake pedal firmly and bring the vehicle to an immediate stop.

D The brake system warning light re- mains on together with the “ABS” warning light. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely un- stable during braking.

to

reminder

remind you

light and buzzer

This buckle up the driver’s seat belt. Once the ignition key is turned to “ON”, the flashes and buzzer sounds if the driver’s seat belt is not fas- tened. Unless the driver fastens the belt, the light keeps flashing and the buzzer stops after about 4 to 8 seconds. (c) Front Seat

Passenger’s

light

Belt

Reminder Light

This light reminds you to buckle up the front passenger’s seat belt. Once the ignition key is turned to “ON”, the reminder light flashes if a passenger sits in the front passenger seat and does not fasten the seat belt. If luggage or other load is placed on the front passenger seat, depending on its weight, the reminder light may come on. (d) Discharge Warning Light This light warns that the battery is being discharged. If it comes on while you are driving, there is a problem somewhere in the charging system.

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

The engine ignition will continue to oper- the battery ate, however, until is dis- charged. Turn off the air conditioning, blower, radio, etc., and drive directly to the nearest Toyota dealer or repair shop.

NOTICE

Do not continue driving if the engine drive belt is broken or loose.

(e) Low Engine Oil Pressure Warning

Light

This light warns that the engine oil pres- sure is too low. If it flickers or stays on while you are driving, pull off the road to a safe place and stop the engine immediately. Call a Toyota dealer or qualified repair shop for assistance. The flicker when the engine is idling or it may come on briefly after a hard stop. There is no cause for concern if it then goes out when the engine is accelerated slightly. The light may come on when the oil level is extremely is not designed to indicate low oil level, and the oil level must be checked using the level dipstick.

light may occasionally

low. It

NOTICE

the Do not drive warning light on—even for one block. It may ruin the engine.

the vehicle with

(f) Malfunction Indicator Lamp This lamp comes on when the ignition key is turned to the “ON” position and goes off after the engine starts. This means that the warning light system is operating properly. If the lamp remains on, or the lamp comes on while driving, first check the followings. D Empty fuel tank

If the fuel tank is empty, refuel immedi- ately.

D Loose fuel tank cap

If the fuel tank cap is loose, securely tighten it.

These cases are temporary malfunctions. The malfunction indicator lamp will go off after taking several driving trips. If the lamp will not go off even after the several trips, contact your Toyota dealer as soon as possible.

If the fuel tank is not empty or the fuel tank cap is not loose... D There is a problem somewhere in the engine, emission control system, elec- tronic throttle control system, automatic transmission electrical system or warn- ing light system itself.

In this case, slow down and have your vehicle checked/repaired by your Toyota dealer as soon as possible. If the engine speed does not increase with the accelerator pedal depressed down, there may be a problem somewhere in your electronic throttle control system. At this time, vibration may occur. Howev- er, if you depress the accelerator pedal more firmly and slowly, you can drive your vehicle at low speeds. Have your vehicle checked by your Toyota dealer as soon as possible. Even if the abnormality of the electronic throttle control system is corrected during low speed driving, the system may not be recovered until the engine is stopped and the ignition key to “ACC” or “LOCK” position.

turned

is

133

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

if

few seconds. Thereafter,

(h) “ABS” Warning Light The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system and the brake assist system work properly, the light turns off after a the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, the traction control system and the vehicle stability control system do not operate, but the brake system still oper- ates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

in

the following conditions If either of indicates a malfunction occurs, this somewhere the components moni- tored by the warning light system. Con- tact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.

D The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem.

CAUTION

If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.

CAUTION

Be especially careful to prevent erro- neous pedal operation.

if

control

system

inspection

Emissions Inspection and Maintenance (I/M) programs Your vehicle may not pass a state emission the malfunction indicator lamp remains on. Contact your to check your vehicle’s Toyota dealer emission and OBD (On−Board Diagnostics) system before taking your vehicle for the inspection. For details, see “Emissions Inspection and Maintenance (I/M) programs” on page 362
in Section 6. (g) Low Fuel Level Warning Light This light comes on when the fuel level in the tank becomes nearly empty. Fill up the tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the low fuel level warning light may come on earlier than usual.

134

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

(i) Open Door Warning Light and Buzz-

er

the side This light remains on until all doors and back door are completely closed. If the vehicle speed rises above 5 km/h (3 mph) with any door open, a buzzer sounds. (j) Automatic

Transmission

Fluid

Temperature Warning Light

This light warns that the automatic trans- mission fluid temperature is too high. If this light comes on while you are driv- ing, slow down and pull off the road. Stop the vehicle at a safe place and put the selector lever in “P”. With the engine id- ling, wait until the light goes off. If the light goes off, you can start the vehicle again. If the light does not go off, call a Toyota dealer or qualified repair shop for assistance.

NOTICE

Continued driving with the warning light on may damage the automatic transmission.

’04 HIGHLANDER_U (L/O 0308)

light system monitors

(k) SRS Warning Light This light will come on when the igni- tion key is turned to the “ON” position. After about 6 seconds, the light will go off. This means the systems of the air- bag and front seat belt pretensioners are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, side and curtain shield airbag sen- sors, curtain shield airbag sensors, driv- er’s seat position sensor, driver’s seat belt buckle switch, front passenger occupant classification system, “AIRBAG ON” indi- cator light, “AIRBAG OFF” indicator light, front passenger’s seat belt buckle switch, seat belt pretensioner assemblies, inflat- ors, warning light, interconnecting wiring and power sources. If either of the following conditions occurs, this indicates a malfunction somewhere in the parts monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, remains on for more than 6 sec- onds or flashes.

If the light stays on, it indicates that the SRS driver and front passenger airbag system and/or front passenger occupant classification system and “AIRBAG ON” and “AIRBAG OFF” indicator lights have a problem. If the light flashes, the SRS side airbag system and/or curtain shield airbag system have a problem. (l) “VSC” Warning Light This light warns that there is a problem somewhere in the vehicle stability control system or traction control system. The light will come on when the ignition key is turned to “ON”, and will go off after a few seconds. If the light comes on while driving, the system does not work. However, as con- ventional braking operates when applied, there is no problem to continue your driv- ing. In the following cases, contact your Toyota dealer: D The warning light does not come on after the ignition key is turned to “ON”. D The warning light remains on after the

ignition key is turned to “ON”.

D The warning light comes on while driv-

D The light comes on or flashes while

ing.

driving.

135

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

is

the

turned

ignition key

Two−wheel drive models only—The “TRAC OFF” indicator light will come on when the “VSC” warning light comes on even if the “TRAC OFF” switch is not pushed. (m) Low Tire Pressure Warning Light This light warns that the tire inflation pres- sure is critically low. The light comes on when to the “ON” position. It goes off after a few sec- onds. This indicates that the low tire pres- sure warning system is functioning proper- ly. If the light comes on while driving, adjust tire inflation pressure to the specified lev- el. (See “Tires” on page 402 in Section 8.) After the tire inflation pressure is adjusted, push the tire pressure warning system re- set switch for a few seconds and make sure the warning light goes off. If the light still remains or blinks slowly (every 0.5
seconds), have the low tire pressure warn- ing system checked at your Toyota dealer. If the light blinks rapidly (every 0.25 sec- onds), the low tire pressure warning sys- tem needs to be initialized. For details, see “Tire pressure warning system” on page 155 in Section 1−7.

(n) Low Windshield Washer Fluid Level

Warning Light

The light warns that the windshield washer fluid level is too low. Add washer fluid at your earliest opportunity. (For instructions, see “Adding washer fluid” on page 391 in Section 7−3.) (o) Engine Oil Replacement Reminder

Light (for vehicles sold in U.S.A.)

then flashes

This light reminds you when to replace the engine oil. This light will come on when the ignition key is turned to “ON” and will go off after about a few seconds. When you drive for about 7200 km (4500
miles) after the engine oil replacement, this light illuminates for about 3 seconds and for about 12 seconds with the ignition key turned to the “ON” position. If you continue driving without replacing the engine oil, and if the dis- tance driven exceeds 8000 km (5000
miles), the light will come on after the ignition key turned to “ON” position. The light will remain on thereafter. If the light is flashing, we recommend that you replace the engine oil at an early opportunity depending on the driving and road conditions. light comes on, replace it as soon as possible.

the

is

If

The system must be reset after the en- gine oil replacement. Reset the system by the following procedure: 1. Turn the ignition key to the “OFF” posi- tion with the odometer reading shown. (For details, see “Odometer and two trip meters” on page 127 in this Sec- tion.)

2. Turn the ignition key to the “ON” posi- tion while holding down the trip meter reset knob.

indicates

Hold down the knob for at least 5 sec- onds. The odometer “000000” and the light goes off. If the system fails to reset, the light will continue flashing. (p) Key Reminder Buzzer This buzzer reminds you to remove the key when you open the driver’s door with the ignition key in the “ACC” or “LOCK” position.

136

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

light

SERVICE

CHECKING REMINDER INDICATORS (except the low fuel level warning low windshield washer fluid level warning light) 1. Apply the parking brake. 2. Open one of the side doors or back

and

door. The open door warning come on.

light should

3. Close the door.

The open door warning light should go off.

4. Turn the ignition key to “ON”, but do

low

lights,

not start the engine. All the service reminder indicators ex- cept the open door warning light should come on. The “ABS” and “VSC” warn- ing tire pressure warning light and engine oil replacement re- minder light go off after a few seconds. The SRS warning light goes off after about 6 seconds. (The “TRAC OFF” indicator light and slip indicator light also come on and go off after a few seconds.)

If any service reminder indicator or warn- ing buzzer does not function as described above, have it checked by your Toyota dealer as soon as possible.

137

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

138

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

SECTION 1− 7

OPERATION OF INSTRUMENTS AND CONTROLS Ignition switch, Transmission and Parking brake Ignition switch with steering lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Automatic transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Traction control system Vehicle stability control system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Tire pressure warning system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Parking brake Cruise control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

140
141
150
154
155
159
159

139

2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)

’04 HIGHLANDER_U (L/O 0308)

Ignition switch with steering lock

NOTICE

leave the key

in the “ON” Do not position if the engine is not running. The battery will discharge and the ignition could be damaged.

“LOCK”—Engine is off and the steering wheel is locked. The key can be re- moved only at this position. You must push in the key to turn it from “ACC” to the “LOCK” position. The selec- tor lever must be in the “P” position be- fore pushing the key. Vehicles with engine immobilizer sys- tem—Once you remove the key, the en- gine immobilizer system is automatically set. (See “Engine immobilizer system” on page 15 in Section 1−2.) When starting the engine, the key may seem stuck at the “LOCK” position. To free it, first be sure the key is pushed all the way in, and then rock the steering wheel slightly while turning the key gently. 2AZ−FE engine only—Approximately five hours after the engine is turned off, you may hear sound coming from underneath the luggage compartment for several min- utes. This is normal operation and does not “Leak indicate a malfunction. detection pump” on page viii.)