2012 Toyota FJ Cruiser Owners Manual

cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

188

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 1130 lb. (510
kg), the available amount of cargo and luggage load capacity will be as follows: 1130 lb. − 366 lb. = 764 lb. (510 kg − 166 kg = 344 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

764 lb. − 388 lb. = 376 lb. (344 kg − 176 kg = 168 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

189

2-5. Driving information

CAUTION

■Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment. ●Receptacles containing gasoline ●Aerosol cans

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Do not place cargo or luggage in or on the following locations as the item may get under the clutch, brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Instrument panel • Dashboard • Auxiliary box or tray that has no lid

●Do not stack anything in the luggage compartment higher than the

seatbacks. Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

●Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious injury, in the event of sudden braking, sudden swerv- ing or an accident.

190

2-5. Driving information

CAUTION

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

191

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, TWR (Trailer Weight Rating) and cargo capacity. ■ Total load capacity: 1130 lb. (510 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

■ Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity.

■ TWR (Trailer Weight Rating): 4700 lb. (2130 kg)

TWR means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

■ Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

■Total load capacity and seating capacity

These details are also described on the tire and loading information label.(→P. 403)

CAUTION

■Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

192

2

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. ■ Pre-winter preparations

● Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

● Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

● Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the rear tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. ■ Before driving the vehicle

Perform the following according to the driving conditions. ● Do not try to forcibly open a window, scrape an outside rear view mirror surface or move a wiper or outside rear view mir- ror that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing.

● To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

● Remove any ice that has accumulated on the vehicle chassis. ● Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

193

2-5. Driving information

■ When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

■ When parking the vehicle

Park the vehicle and move the shift lever to P (automatic trans- mission) or to 1 or R (manual transmission) without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

Regulations on the use of snow chains

● Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains.

● Install the chains on the rear tires. ● Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

■Snow chain installation

Observe the following precautions when installing and removing chains. ●Install and remove tire chains in a safe location. ●Install tire chains on the rear tires only. Do not install tire chains on the

front tires.

●Install tire chains following the instructions provided in the accompanying

instructions.

194

2-5. Driving information

CAUTION

■Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. ●Use tires of the size specified for your vehicle. ●Maintain the recommended level of air pressure. ●Do not drive in excess of 75 mph (120 km/h) regardless of the type of

snow tires being used.

●Snow tires should be installed on all wheels. ●4WD models:

Do not mix tires of different makes, models, tread patterns or treadwear.

■Driving with snow chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. ●Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

●Avoid driving on bumpy road surfaces or over potholes. ●Avoid sudden turns and braking. ●Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

■Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

■Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

195

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger-and-load-carrying vehicle. Towing a trailer can have an adverse impact on handling, performance, braking, durability, and fuel consumption. For your safety and the safety of others, you must not overload your vehicle or trailer. You must also ensure that you are using appropriate tow- ing equipment, that the towing equipment has been installed cor- rectly and used properly, and that you employ the requisite driving habits. Vehicle-trailer stability and braking performance are affected by trailer stability, brake performance and setting, trailer brakes, the hitch and hitch systems (if equipped). To tow a trailer safely, use extreme care and drive the vehicle in accordance with your trailer’s characteristics and operating condi- tions. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Contact your Toyota dealer for further information about additional requirements such as towing kits, etc.

196

2

2-5. Driving information

Towing related terms

■ GCWR (Gross Combination Weight Rating)

The maximum allowable gross combination weight. The gross combination weight is the sum of the total vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the weight of the trailer being towed (including the cargo in the trailer).

■ GVWR (Gross Vehicle Weight Rating)

The maximum allowable gross vehicle weight. The gross vehicle weight is the total weight of the vehicle. When towing a trailer, it is the sum of the vehicle weight (including the occupants, cargo and any optional equipment installed on the vehicle) and the tongue weight.

197

2-5. Driving information

■ GAWR (Gross Axle Weight Rating)

Front GAWR

Rear GAWR

The maximum allowable gross axle weight. The gross axle weight is the load placed on each axle (front and rear).

■ TWR (Trailer Weight Rating)

(With brakes)

The maximum allowable gross trailer weight. The gross trailer weight is the sum of the trailer weight and the weight of the cargo in the trailer. TWR is calculated assuming base vehicle with one driver, one front passenger, towing package (if available), hitch and hitch sys- tems (if required).

Additional optional equipment, passengers and cargo in the vehi- cle will reduce the trailer weight rating so as not to exceed GCWR, GVWR and GAWR. If the gross trailer weight exceeds 3000 lb. (1360 kg), it is recom- mended to use a trailer with 2 or more axles.

198

2-5. Driving information

■ Unbraked TWR (Unbraked Trailer Weight Rating) (Without brakes)

The trailer weight rating for tow- ing a trailer without a trailer ser- vice brake system.

■ Tongue Weight

The load placed on the trailer hitch ball. (→P. 202)

199

2-5. Driving information

Weight limits

● The gross trailer weight must never exceed the TWR described in

the table. (→P. 201)

● The gross combination weight must never exceed the GCWR

described in the table. (→P. 201)

● The gross vehicle weight must never exceed the GVWR indi- cated on the Certification Label.

● The gross axle weight on each axle must never exceed the GAWR indicated on the Certi- fication Label.

● If the gross trailer weight is over the unbraked TWR, trailer service

brakes are required.

● If the gross trailer weight is over 2000 lb. (907 kg), a sway control

device with sufficient capacity is required.

200

2-5. Driving information

GCWR, TWR and Unbraked TWR

Confirm that the gross trailer weight, gross combination weight, gross vehicle weight, gross axle weight and tongue weight are all within the limits.

■ GCWR* and TWR*

Model code*1

Engine

Driving system 2WD

GCWR

TWR

engine

9200 lb. (4170 kg)

4.0L V6 (1GR-FE)

GSJ10L-GKASKA GSJ15L-GKFSKA GSJ15L-GKASKA *1: The model code is indicated on the Certification Label. (→P. 483) ■ Unbraked TWR* 1000 lb. (453 kg)

9500 lb. (4305 kg)

4WD

4700 lb. (2130 kg)

*: These models meet the tow-vehicle trailering requirement of SAE

International per SAE J2807.

201

2-5. Driving information

Trailer Tongue Weight

● A recommended tongue weight varies in accordance with the types

of trailers or towing as described below.

● To ensure the recommended values shown below, the trailer must

be loaded by referring to the following instructions. • Tongue Weight

The gross trailer weight should be distributed so that the tongue weight is 9% to 11%. (Tongue weight /Gross trailer weight x 100
= 9% to 11%)

Gross trailer weight Tongue weight

If using a weight distributing hitch when towing, return the front axle to the same weight as before the trailer connection. If front axle weight cannot be measured directly, measure the front fender height above the front axle before connection. Adjust weight distributing hitch torque until front fender is returned to the same height as before connection. The gross trailer weight, gross axle weight and tongue weight can be measured with platform scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

202

2-5. Driving information

Hitch

Trailer hitch assemblies have different weight capacities. Toyota rec- ommends the use of Toyota hitch/bracket for your vehicle. For details, contact your Toyota dealer. ● If you wish to install a trailer hitch, contact your Toyota dealer. ● Use only a hitch that conforms to the gross trailer weight require-

ment of your vehicle.

● Follow the directions supplied by the hitch manufacturer. ● Lubricate the hitch ball with a light coating of grease. ● Remove the trailer hitch whenever you are not towing a trailer. After removing the hitch, seal any mounting hole in the vehicle body to prevent entry of any substances into the vehicle.

203

2-5. Driving information

Selecting trailer ball

Use the correct trailer ball for your application.

Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers are stamped with the required trailer ball size.

Trailer class

Typical trailer ball size

IV

2 5/16 in.

II and III

2 in.

1 7/8 in.

Shank length Protrudes beyond the bottom of the lock washer and nut by at least 2 threads. Shank diameter Matches diameter size.

the ball mount hole

204

2-5. Driving information

Positions for towing hitch receiver and hitch ball

Weight carrying ball position: 43.3 in. (1100 mm) Hitch receiver pin hole posi- tion: 39.4 in. (1000 mm)

Connecting trailer lights

Use the wire harness stored in the rear end under body.

205

2-5. Driving information

Trailer towing tips

Your vehicle will handle differently when towing a trailer. Help to avoid an accident, death or serious injury, keep the following in mind when towing: ● Speed limits for towing a trailer vary by state or province. Do not

exceed the posted towing speed limit.

● Toyota recommends that the vehicle-trailer speed limit is 65 mph (104 km/h) on a flat, straight, dry road. Do not exceed this limit, the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Instability of the towing vehicle-trailer combination (trailer sway) increases as speed increases. Exceeding speed limits may cause loss of con- trol.

● Before starting out, check the trailer lights, tires and the vehicle-

trailer connections. Recheck after driving a short distance.

● Practice turning, stopping and reversing with the trailer attached in an area away from traffic until you become accustomed to the feel of the vehicle-trailer combination.

● Reversing with a trailer attached is difficult and requires practice. Grip the bottom of the steering wheel and move your hand to the left to move the trailer to the left. Move your hand to the right to move the trailer to the right. (This is generally opposite to reversing without a trailer attached.) Avoid sharp or prolonged turning. Have someone guide you when reversing to reduce the risk of an acci- dent.

● As stopping distance is increased when towing a trailer, vehicle-to- vehicle distance should be increased. For each 10 mph (16 km/h) of speed, allow at least one vehicle and trailer length.

● Avoid sudden braking as you may skid, resulting in the trailer jack- knifing and a loss of vehicle control. This is especially true on wet or slippery surfaces.

206

2-5. Driving information

● Avoid jerky starts or sudden acceleration. ● Avoid jerky steering and sharp turns, and slow down before mak-

ing a turn.

● Note that when making a turn, the trailer wheels will be closer than the vehicle wheels to the inside of the turn. Compensate by making a wider than normal turning radius.

● Slow down before making a turn, in crosswinds, on wet or slippery

surfaces, etc. Increasing vehicle speed can destabilize the trailer.

● Take care when passing other vehicles. Passing requires consider- able distance. After passing a vehicle, do not forget the length of your trailer, and be sure you have plenty of room before changing lanes.

● To maintain engine braking efficiency and charging system perfor- mance when using engine braking, do not use sixth gear (manual transmission), or do not put the transmission in D (automatic trans- mission).

● Instability happens more frequently when descending steep or long downhill grades. Before descending, slow down and downshift. Do not make sudden downshifts while descending steep or long down- hill grades.

● Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

● Due to the added load of the trailer, your vehicle’s engine may overheat on hot days (at temperatures over 85°F [30°C]) when driving up a long or steep grade. If the engine coolant temperature gauge indicates overheating, immediately turn off the air condition- ing (if in use), pull your vehicle off the road and stop in a safe spot. (→P. 474)

207

2-5. Driving information

● Always place wheel blocks under both the vehicle’s and the trailer’s wheels when parking. Apply the parking brake firmly, and put the transmission in P (automatic transmission) or in 1 or R (manual transmission). Avoid parking on a slope, but if unavoid- able, do so only after performing the following: Apply the brakes and keep them applied. Have someone place wheel blocks under both the vehicle’s and trailer’s wheels. When the wheel blocks are in place, release the brakes slowly until the blocks absorb the load. Apply the parking brake firmly. Shift into P (automatic transmission) or 1 or R (manual trans- mission) and turn off the engine.

● When restarting after parking on a slope:

With the transmission in P (automatic transmission) or the clutch pedal (manual transmission) depressed, start the engine. On vehicles with an automatic transmission, be sure to keep the brake pedal depressed. Shift into a forward gear. If reversing, shift into R. Release the parking brake (and also the brake pedal on vehi- cles with an automatic transmission), and slowly pull or back away from the wheel blocks. Stop and apply the brakes. Have someone retrieve the blocks.

208

2-5. Driving information

■Matching trailer ball height to trailer coupler height

No matter which class of tow hitch applies, for a more safe trailer hookup, the trailer ball setup must be the proper height for the coupler on the trailer.

Coupler Trailer ball

■Before towing

Check that the following conditions are met: ●Ensure that your vehicle’s tires are properly inflated. (→P. 491) ●Trailer tires are inflated according to the trailer manufacturer’s recom-

mendation.

●All trailer lights work as required by law. ●All lights work each time you connect them. ●The trailer ball is set at the proper height for the coupler on the trailer. ●The vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue weight, overloading, worn suspension, or other possible causes.

●The trailer cargo is securely loaded. ●The rear view mirrors conform to all applicable federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes.

209

2-5. Driving information

■Break-in schedule

If your vehicle is new or equipped with any new power train components (such as an engine, transmission, differential or wheel bearing), Toyota rec- ommends that you do not tow a trailer until the vehicle has been driven for over 500 miles (800 km). After the vehicle has been driven for over 500 miles (800 km), you can start towing. However, for the next 500 miles (800 km), drive the vehicle at a speed of less than 50 mph (80 km/h) when towing a trailer, and avoid full throttle acceleration.

■Maintenance

●If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Owner’s Warranty Information Booklet” or “Scheduled Maintenance Guide/Owner’s Manual Supplement”.)

●Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km) of trailer towing.

■If trailer sway occurs

One or more factors (crosswinds, passing vehicles, rough roads, etc.) can adversely affect handling of your vehicle and trailer, causing instability. ●If trailer swaying occurs:

• Firmly grip the steering wheel. Steer straight ahead.

Do not try to control trailer swaying by turning the steering wheel.

• Begin releasing the accelerator pedal immediately but very gradually to

reduce speed. Do not increase speed. Do not apply vehicle brakes.

If you make no extreme correction with the steering or brakes, your vehicle and trailer should stabilize. ●After the trailer swaying has stopped:

• Stop in a safe place. Get all occupants out of the vehicle. • Check the tires of the vehicle and the trailer. • Check the load in the trailer.

Make sure the load has not shifted. Make sure the tongue weight is appropriate, if possible.

• Check the load in the vehicle.

Make sure the vehicle is not overloaded after occupants get in.

210

2

2-5. Driving information

If you cannot find any problems, the speed at which trailer swaying occurred is beyond the limit of your particular vehicle-trailer combination. Drive at a lower speed to prevent instability. Remember that swaying of the towing vehicle-trailer increases as speed increases.

CAUTION

■Trailer towing precautions

To tow a trailer safely, use extreme care and drive the vehicle in accordance with the trailer’s characteristics and operating conditions. Failure to do so could cause an accident resulting in death or serious injury. Vehicle stability and braking performance are affected by trailer stability, brake setting and performance, and the hitch. Your vehicle will handle differently when towing a trailer.

■To avoid accident or injury

●Do not exceed the TWR, unbraked TWR, GCWR, GVWR or GAWR. ●If the gross trailer weight is over 2000 lb. (907 kg), a sway control device

with sufficient capacity is required.

●Adjust the tongue weight within the appropriate range. Place heavier loads

as close to the trailer axle as possible.

●Do not exceed 65 mph (104 km/h), the posted towing speed limit or the speed limit for your trailer as set forth in your trailer owner’s manual, whichever is lowest. Slow down sufficiently before making a turn, in cross winds, on wet or slippery surface, etc. to help avoid an accident. If you experience a vehicle-trailer instability from reducing a certain speed, slow down and make sure you keep your vehicle speed under the speed of which you experience the instability.

●Do not make jerky, abrupt or sharp turns. ●Do not apply the brakes suddenly as you may skid, resulting in jackknifing and loss of vehicle control. This is especially true on wet or slippery sur- faces.

●Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue weight capacities.

●Do not use cruise control when towing.

211

2-5. Driving information

CAUTION

■To avoid accident or injury

●Slow down and downshift before descending steep or long downhill grades. Do not make sudden downshifts while descending steep or long downhill grades.

●Vehicle-trailer instability is more likely on steep long downhills. Before descending steep or long downhill grades, slow down and downshift. Do not make sudden downshifts when descending steep or long downhill grades. Avoid holding the brake pedal down too long or applying the brakes too frequently. This could cause the brakes to overheat and result in reduced braking efficiency.

■Hitch

Trailer hitch assemblies have different weight capacities established by the hitch manufacturer. Even though the vehicle may be physically capable of towing a higher weight, the operator must determine the maximum weight rating of the particular hitch assembly and never exceed the maximum weight rating specified for the trailer-hitch. Exceeding the maximum weight rating set by the trailer-hitch manufacturer can cause an accident resulting in death or serious personal injuries.

■When towing a trailer

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations. ●If the gross trailer weight exceeds unbraked TWR, trailer brakes are required. Toyota recommends trailers with brakes that conform to all appli- cable federal and state/provincial regulations.

●Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

●Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

212

2-5. Driving information

NOTICE

■When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

■Do not directly splice trailer lights

Do not directly splice trailer lights. Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

213

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

■To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

214

2-5. Driving information

215

3-1. Using the air conditioning system and defogger Air conditioning system

Outside air or recirculated air mode switch

Air conditioning ON/OFF switch

Fan speed control dial

Temperature control dial

Air outlet selection dial

Adjusting the settings

■ Adjusting the temperature setting

Turn the temperature control dial clockwise (warm) or counter- clockwise (cool).

A/C

is not pressed, the system will blow ambient temperature air or

If heated air. For quick cooling, turn the temperature control dial to the MAX A/C position. The air conditioning will automatically turn on and the air intake selector will be set to recirculated air mode.

218

3-1. Using the air conditioning system and defogger

■ Adjusting the fan speed

Turn the fan speed control dial clockwise (increase) or counter- clockwise (decrease). Set the dial to OFF to turn the fan off.

■ Selecting the air outlets

Set the air outlet selection dial to an appropriate position. The positions between the air outlet selections shown below can also be selected for more detailed adjustment.

When the dial is set to flows to the upper body.

, air

When the dial is set to , air flows to the upper body and feet.

When the dial is set to mainly air flows to the feet.

219

3-1. Using the air conditioning system and defogger

When the dial is set to , air flows to the feet and the wind- shield defogger operates.

The air intake selector is automat- ically set to outside air mode. To return

the recirculated air

mode, press

When the dial is set to , air flows to the windshield and side windows to defog them.

The air intake selector is automat- ically set to outside air mode. In this position, the air intake selector cannot be changed to the recirculated air mode.

■ Switching between outside air and recirculated air modes

Press

The mode switches between

(outside air mode) and

(recirculated air mode) each time the switch is pressed.

220

3-1. Using the air conditioning system and defogger

■ If the ambient temperature drops while using the recirculated

air mode The air intake mode automatically changes from recirculated air mode to outside air mode after a few minutes. To cancel this function:

Press and hold

for longer than 2 seconds.

To reactivate this function: Turn the engine switch to the LOCK or ACC position.

Adjusting the position of the air outlets

Center outlets

Direct air flow to the left or right, up or down.

221

3-1. Using the air conditioning system and defogger

Right and left side outlets

Direct air flow to the left or right, up or down.

Opening and closing the right and left side outlets

Open the vent. Close the vent.

222

3-1. Using the air conditioning system and defogger

■Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

■When outside air temperature approaches 32°F (0°C)

The air conditioning system may not operate even when

A/C

is pressed.

■When

is selected for the air outlets used

For your driving comfort, air flowing to the feet may be warmer than air flow- ing to the upper body depending on the position of the temperature adjust- ment dial.

■When the indicator on

A/C

flashes

A/C

and turn off the air conditioning system before turning it on Press once more. There may be a problem in the air conditioning system if the indi- cator continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

■Air conditioning odors

●During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system. This may then cause odor to be emitted from the vents.

●To reduce potential odors from occurring:

It is recommended that the air conditioning system be set to outside air mode prior to turning the vehicle off.

CAUTION

■To prevent the windshield from fogging up

Do not set the air outlet selection dial to during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

223

3-1. Using the air conditioning system and defogger

NOTICE

■To prevent battery discharge

Do not leave the air conditioning system on longer than necessary when the engine is stopped.

224

3-1. Using the air conditioning system and defogger Rear window defogger

This feature is used to defog the rear window.

On/off

Press the button to turn on the rear window defogger. The indicator light will come on. The defogger will automatically turn off after 15 to 240 minutes. The operation time changes according to the ambient tem- perature and vehicle speed. Pressing the button again also turns the defogger off.

■The rear window defogger can be operated when

The engine switch is in the ON position.

NOTICE

■To prevent battery discharge

Turn the rear window defogger off when the engine is off.

225

3-2. Using the audio system Audio system

Type A: CD player with changer controller and AM/FM radio

Type B: CD player with changer and AM/FM radio

226

3-2. Using the audio system

Title

Using the radio Using the CD player Playing MP3 and WMA discs Operating an iPod Operating a USB memory Optimal use of the audio system Using the AUX port Using the steering wheel audio switches

Page P. 230
P. 237
P. 245
P. 252
P. 259
P. 267
P. 270
P. 271

Language settings

The language used for all voice guidance, voice recognition and mes- sages may be changed.

Press

Press Press Press

(MORE). (LANG). or

that corresponds to the desired language.

For vehicles sold in the U.S.A. “ENG” (English) or “ESP” (Spanish) For vehicles sold in Canada “ENG” (English) or “FRAN” (French)

227

3-2. Using the audio system

■Using cellular phones

Interference may be heard through the audio system’s speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

■Certification for the audio system

This device complies with part 15 of the FCC Rules and RSS-Gen of the IC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired oper- ation.

CAUTION

■For vehicles sold in U.S.A. and Canada

●Part 15 of the FCC Rules and RSS-Gen of the IC Rules

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

●Laser products

• Do not take this unit apart or attempt to make any changes by yourself. This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

• The use of optical instruments with this product will increase eye haz-

ard.

228

3-2. Using the audio system

NOTICE

■To prevent battery discharge

Do not leave the audio system on longer than necessary with the engine off.

■To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

229

3-2. Using the audio system Using the radio

Power

Volume

Scanning for receivable stations

Station selector

Adjusting the frequency (AM, FM mode) or channel (SAT mode) Displaying radio text messages

Mute

Seeking the frequency

Setting preset button

AM/FM/SAT mode button

Changing the channel category

Setting station presets (excluding XM® Satellite Radio)

Search for desired stations by turning

or pressing

“∧” or “∨” on Press and hold a button (from beep.

to

) until you hear a

Each time total of 6 pages.

is pressed, station pages are changed. There are a

230

3-2. Using the audio system

Scanning radio stations (excluding XM® Satellite Radio)

■ Scanning the preset radio stations

Press and hold

until you hear a beep.

Preset stations will be played for 5 seconds each.

When the desired station is reached, press

again.

■ Scanning all radio stations within range

Press

All the stations with reception will be played for 5 seconds each.

When the desired station is reached, press

again.

■ Displaying radio text messages (FM mode only)

When a new radio text message is received, “MSG” is shown on

the display. To display the message, press

If the text continues past the end of the display, “

” is displayed. Press

and hold

until you hear a beep.

Text messages are not displayed while driving.

231

3-2. Using the audio system

XM® Satellite Radio (if equipped) ■ Receiving XM® Satellite Radio

Press

The display changes as follows each time AM → FM → XM

is pressed.

Turn

to select the desired channel in all the catego-

ries or press “∧” or “∨” on nel in the current category.

to select the desired chan-

■ Setting XM® Satellite Radio channel presets

Select the desired channel. Press and hold a button (from

to

) until you hear a beep.

Each time 6 pages.

is pressed, station pages are changed. There are a total of

■ Changing the channel category

Press “∧” or “∨” on

232

3-2. Using the audio system

■ Scanning XM® Satellite Radio channels

● Scanning channels in the current category

Press

When the desired channel is reached, press again.

● Scanning the preset channels

Press and hold

until you hear a beep.

When the desired channel is reached, press again.

■ Displaying text information

Press

Each time

is pressed, the display changes in the following order:

Title (song/program title) → Name (artist name/feature)/Title (song/pro- gram title).

233

3-2. Using the audio system

■Reception sensitivity

●Cargo loaded on the roof luggage carrier, especially metal objects, may

adversely affect the reception of XM® Satellite Radio.

●Maintaining perfect radio reception at all times is difficult due to the con- tinually changing position of the antenna, differences in signal strength and surrounding objects, such as trains, transmitters, etc.

●The radio antenna is mounted on the right-side front fender. The antenna

can be removed from the base by turning it.

■XM® Satellite Radio

An XM® Satellite Radio is a tuner designed exclusively to receive broadcasts provided under a separate subscription. Availability is limited to the 48 con- tiguous states and 10 Canadian provinces. ●XM® subscriptions

For detailed information about XM® Satellite Radio or to subscribe: U.S.A. ⎯ Visit on the web at www.xmradio.com or call 1-800-967-2346. Canada ⎯ Visit on the web at www.xmradio.ca or call 1-877-209-0079.

●Radio ID

You will need the radio ID when activating XM® service or reporting a

problem. Select “CH000” using

, and the receiver’s 8-character

ID number will appear.

●Satellite tuner

The tuner supports only Audio Services (Music and Talk) and the accom- panying Text Information of XM® Satellite Radio.

234

3-2. Using the audio system

■If XM® Satellite Radio does not operate normally

If a problem occurs with the XM® tuner, a message will appear on the dis- play. Refer to the table below to identify the problem, and take the suggested corrective action.

CHECK ANTENNA

CHANNEL NOT AUTHORIZED

NO SIGNAL

LOADING

CHANNEL OFF

AIR

Blank

The XM® antenna is not connected. Check whether the XM® antenna cable is attached securely. There is a short-circuit in the antenna or the sur- rounding antenna cable. See a Toyota certified dealer. You have not subscribed to XM® Satellite Radio. The radio is being updated with the latest encryp- tion code. Contact XM® Satellite Radio for sub- scription information. When a contract is canceled, you can choose the “CH000” and all free-to-air channels. The premium channel you selected is not autho- rized. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel. If you want to listen to the premium chan- nel, contact XM® Satellite Radio. The XM® signal is too weak at the current location. Wait until your vehicle reaches a location with a stronger signal. The unit is acquiring audio or program information. Wait until the unit has received the information. The channel you selected is not broadcasting any programming. Select another channel. There is no song/program title or artist name/fea- ture associated with the channel at this time. No action needed.

235

3-2. Using the audio system

CHANNEL NOT

AVAILABLE

The channel you selected is no longer available. Wait for about 2 seconds until the radio returns to the previous channel or “CH001”. If it does not change automatically, select another channel.

Contact the XM® Listener Care Center at 1-800-967-2346 (U.S.A.) or 1-877- 209-0079 (Canada)

■Certifications for the radio tuner

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How- ever, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by trying one or more of the following: ●Reorienting or relocating the receiving antenna. ●Increasing the separation between the equipment and receiver. ●Connecting the equipment into an outlet on a circuit different from that to

which the receiver is connected.

●Consulting the dealer or an experienced radio/TV technician for help.

NOTICE

■To prevent damage, remove the antenna in the following cases.

●The antenna will touch the ceiling of a garage. ●A cover will be put on the vehicle.

236

3-2. Using the audio system Using the CD player

Power

PWR VOL

Volume

PWR VOL

CD eject

Searching playback Selector buttons

CD load (type B only)

Displaying text messages

TOYOTA

SCAN

PWR VOL

LOAD

TEXT

TUNE SCROLL

PUSH SELECT

PRESET

Selecting a track

Playback/ pause

Playback

CD

RADIO

AUX

SEEK TRACK

TYPE FOLDER

SET UP

Selecting a track/ fast-forwarding and reversing

STY32AC022

Loading CDs

■ Loading a CD (type A)

Insert a CD.

■ Loading a CD (type B)

Press

When the indicator on the slot turns from amber to green, insert a CD.

237

3-2. Using the audio system

■ Loading multiple CDs (type B only)

Press and hold

until you hear a beep.

When the indicator on the slot turns from amber to green, insert a CD. The indicator on the slot turns to amber when the CD is inserted. When the indicator on the slot turns from amber to green again, insert the next CD. Repeat the procedure for the remaining CDs.

To cancel, press onds, loading will be canceled automatically.

. If you do not insert a disc within 15 sec-

Ejecting CDs

■ Ejecting a CD (type A)

Press

and remove the CD.

■ Ejecting a CD (type B)

To select the CD to be ejected, press The selected CD number is shown on the display.

) or

).

Press

and remove the CD.

■ Ejecting all the CDs (type B only)

Press and hold CDs.

until you hear a beep, and then remove the

238

3-2. Using the audio system

Selecting a track

or press “∧” or “∨” on

to select the desired

Turn

track.

Fast-forwarding and reversing tracks

Press and hold “∧” or “∨” on

Scanning tracks

Press

The first ten seconds of each track will be played.

To cancel, press

again.

Press

again when the desired track is reached.

239

3-2. Using the audio system

Selecting a CD (type B only)

■ Selecting a CD to play

Press

■ Scanning loaded CDs

) or

).

Press and hold

until you hear a beep.

The first ten seconds of the first track on each CD will be played.

To cancel, press

again.

Press

again when the desired CD is reached.

Playing and pausing tracks

Press

Random playback

■ Current CD

(RDM).

Press Songs are played in random order. To cancel, press the button one more (type A), or twice more (type B).

■ All CDs (type B only) (RDM) twice.

Press Tracks on all loaded CDs are played in random order. To cancel, press the button again.

240

3-2. Using the audio system

Repeat play

■ Repeating a track

Press

(RPT).

To cancel, press the button once more (type A), or twice more (type B).

■ Repeating all of the tracks on a CD (type B only)

Press

(RPT) twice.

To cancel, press the button again.

Switching the display

Press

Each time

is pressed, the display changes in the following order:

Track title → Track name/Artist name → Track name/Elapsed time.

■Error messages

“CD CHECK”: This indicates a problem either with the CD or inside the player. The CD may be dirty, damaged or inserted up-side down.

“PLEASE WAIT”: Operation has stopped due to a high temperature inside

the player. Wait for a while and then press your Toyota dealer if the CD still cannot be played back.

. Contact

241

3-2. Using the audio system

■Discs that can be used

Discs with the marks shown below can be used. Playback may not be possible depending on the recording format or disc features, or due to scratches, dirt or deterioration.

CDs with copy-protection features may not be used.

■CD player protection feature

To protect the internal components, playback is automatically stopped when a problem is detected while the CD player is being used.

■If CDs are left inside the CD player or in the ejected position for

extended periods CDs may be damaged and may not play properly.

■Lens cleaners

Do not use lens cleaners. Doing so may damage the CD player.

242

3-2. Using the audio system

NOTICE

■CDs and adapters that cannot be used

Do not use the following types of CDs, 3 in. (8 cm) CD adapters or Dual Discs. Doing so may damage the CD player and/or the CD insert/eject function.

●CD player with changer and AM/FM radio: CDs that have a diameter that is not 4.7 in. (12 cm)

●Low-quality and deformed CDs

●CDs with a transparent or translucent

recording area

●CDs that have had tape, stickers or CD- R labels attached to them, or that have had the label peeled off