2012 Toyota FJ Cruiser Owners Manual

■ How to initialize the tire pressure warning system

Park the vehicle in safe place and turn the engine switch to the LOCK position. While the vehicle is moving, initialization is not performed. Adjust the tire inflation pressure to the specified cold tire infla- tion pressure level. (→P. 491) Make sure to adjust the tire pressure to the specified cold tire inflation pressure level. The tire pressure warning system will operate based on this pressure level. Turn the engine switch to the ON position.

396

4-3. Do-it-yourself maintenance

Press and hold the tire pressure warning reset switch until the tire pressure warning light blinks slowly 3 times.

Wait for a few minutes with the engine switch on, and then turn the engine switch to the ACC or LOCK position.

Registering ID codes

The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code of tire pressure warning valve and transmitter. Have the ID code registered by your Toyota dealer.

397

4-3. Do-it-yourself maintenance

■When to replace your vehicle's tires

Tires should be replaced if: ●You have tire damage such as cuts, splits, cracks deep enough to

expose the fabric or bulges indicating internal damage

●A tire goes flat repeatedly or cannot be properly repaired due to the

size or location of a cut or other damage

If you are not sure, consult with your Toyota dealer.

■Replacing tires and wheels

If the ID code of the tire pressure warning valve and transmitter is not registered, the tire pressure warning system will not work properly. After driving for about 20 minutes, the tire pressure warning light blinks for 1
minute and stays on to indicate a system malfunction.

■Tire life

Any tire over 6 years old must be checked by a qualified technician even if they have seldom or never been used or damage is not obvious.

■If the tread wears down below 0.16 in. (4 mm) on snow tires

The effectiveness of snow tires is lost.

■Maximum load of tire

Check that the number given by dividing the maximum load by 1.10 of the replacement tire is greater than 1/2 of the Gross Axle Weight Ratings (GAWR) of either the front axle or the rear axle, whichever is greater.

For the GAWR, see the Certification Label. For the maximum load of the tire, see the load limit at maximum cold tire inflation pressure mentioned on the sidewall of the tire. (→P. 496)

398

4-3. Do-it-yourself maintenance

■Tire types

1 Summer tires

Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads. For driving on snow-covered roads or icy roads, the use of snow tires is recommended. When installing snow tires, be sure to replace all four tires.

2 All season tires

All season tires are designed to provide better traction in snow and to be adequate for driving in most winter conditions, as well as for use year round. All season tires, however, do not have adequate traction performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving.

3 Snow tires

For driving on snow-covered roads or icy roads, we recommend using snow tires. If you need snow tires, select tires of the same size, con- struction and load capacity as the originally installed tires. Since your vehicle has radial tires as original equipment, make sure your snow tires also have radial construction. Do not install studded tires without first checking local regulations for possible restriction. Snow tires should be installed on all wheels. (→P. 193)

■Initializing the tire pressure warning system

Initialize the tire pressure warning system with the tire inflation pressure adjusted to the specified level.

■If you press the tire pressure warning reset switch accidentally

If initialization is performed, adjust the tire inflation pressure to the speci- fied level and initialize the tire pressure warning system again.

399

4-3. Do-it-yourself maintenance

■When the initialization of the tire pressure warning system has

failed Initialization can be completed in a few minutes. However, in the follow- ing cases, the settings have not been recorded and the system will not operate properly. If repeated attempts to record tire inflation pressure settings are unsuccessful, have the vehicle inspected by your Toyota dealer. ●When operating the tire pressure warning reset switch, the tire pres-

sure warning light does not blink 3 times.

●After carrying out the initialization procedure, the tire pressure warn- ing light blinks for 1 minute then stays on after driving for about 20
minutes.

■Routine tire inflation pressure checks

The tire pressure warning system does not replace routine tire inflation pressure checks. Make sure to check tire inflation pressure as part of your routine of daily vehicle checks.

■Tire pressure warning system certification

FCC ID: PAXPMV107J FCC ID: HYQ13BCX

For vehicles sold in the U.S.A.

NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC WARNING: Changes or modifications not expressly approved by the party responsi- ble for compliance could void the user’s authority to operate the equip- ment.

For vehicles sold in Canada

NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

400

4-3. Do-it-yourself maintenance

CAUTION

■When inspecting or replacing tires

Observe the following precautions to prevent accidents. Failure to do so may cause damage to parts of the drive train, as well as dangerous han- dling characteristics, which may lead to an accident resulting in death or serious injury. ●Do not mix tires of different makes, models or tread patterns. Also, do

not mix tires of remarkably different treadwear.

●Do not use tire sizes other than those recommended by Toyota. ●Do not mix differently constructed tires (radial, bias-belted or bias-ply

tires).

●Do not mix summer, all season and winter tires. ●Do not use tires that have been used on another vehicle. ●Do not use tires if you do not know how they were used previously.

■When initializing the tire pressure warning system

Do not press the tire pressure warning reset switch without first adjusting the tire inflation pressure to the specified level. Otherwise, the tire pres- sure warning light may not come on even if the tire inflation pressure is low, or it may come on when the tire inflation pressure is actually normal.

401

4-3. Do-it-yourself maintenance

NOTICE

■Repairing or replacing tires, wheels, tire pressure warning valves,

transmitters and tire valve caps ●When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled cor- rectly.

●When replacing tire valve caps, do not use tire valve caps other than

those specified. The cap may become stuck.

■To avoid damage to the tire pressure warning valves and transmit-

ters When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (→P. 396)

■Driving on rough roads

Take particular care when driving on roads with loose surfaces or pot- holes. These conditions may cause losses in tire inflation pressure, reducing the cushioning ability of the tires. In addition driving on rough roads may cause damage to the tires themselves, as well as the vehicle’s wheels and body.

■If tire inflation pressures become low while driving

Do not continue driving, or your tires and/or wheels may be ruined.

402

4-3. Do-it-yourself maintenance Tire inflation pressure

■ Tire inflation pressure The recommended cold tire inflation pressure and tire size is dis- played on the tire and loading information label. (→P. 491)

403

4-3. Do-it-yourself maintenance

■ Inspection and adjustment procedure

Tire valve Tire pressure gauge

Remove the tire valve cap. Press the tip of the tire pressure gauge onto the tire valve. Read the pressure using the graduations of the gauge. If the tire inflation pressure is not within the recommended levels, adjust inflate the tire. If you add too much air, press the center of the valve to lower. After completing the tire inflation pressure measurement and adjustment, apply soapy water to the valve and check for leakage. Reinstall the tire valve cap.

404

4-3. Do-it-yourself maintenance

■Tire inflation pressure check interval

You should check tire pressure every two weeks, or at least once a month. Do not forget to check the spare.

■Effects of incorrect tire inflation pressure

Driving with incorrect tire inflation pressure may result in the following: ●Reduced fuel efficiency ●Reduced driving comfort and tire life ●Reduced safety ●Damage to the drive train If a tire needs frequent refilling, have it checked by your Toyota dealer.

■Instructions for checking tire inflation pressure

When checking tire inflation pressure, observe the following: ●Check only when the tires are cold.

If your vehicle has been parked for at least 3 hours and has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.

●Always use a tire pressure gauge.

The appearance of the tire can be misleading. In addition, tire infla- tion pressures that are even just a few pounds off can degrade ride and handling.

●Do not bleed or reduce tire inflation pressure after driving. It is normal

for the tire inflation pressure to be higher after driving.

●Never exceed the vehicle capacity weight.

Passengers and luggage weight should be placed so that the vehicle is balanced.

405

4-3. Do-it-yourself maintenance

CAUTION

■Proper inflation is critical to save tire performance

Keep your tires properly inflated. Otherwise, the following conditions may occur and result in an accident causing death or serious injury. ●Excessive wear ●Uneven wear ●Poor handling ●Possibility of blowouts resulting from overheated tires ●Poor sealing of the tire bead ●Wheel deformation and/or tire separation ●A greater possibility of tire damage from road hazards

NOTICE

■When inspecting and adjusting tire inflation pressure

Be sure to reinstall the tire valve caps. Without the valve caps, dirt or moisture could get into the valve and cause air leakage, which could result in an accident. If the caps have been lost, replace them as soon as possible.

406

4-3. Do-it-yourself maintenance Wheels

If a wheel is bent, cracked or heavily corroded, it should be replaced. Otherwise, the tire may separate from the wheel or cause loss of handling control. ■ Wheel selection

When replacing wheels, care should be taken to ensure that they are equivalent to those removed in load capacity, diameter, rim width, and inset*. Replacement wheels are available at your Toyota dealer. *: Conventionally referred to as “offset”. Toyota does not recommend using: ● Wheels of different sizes or types ● Used wheels ● Bent wheels that have been straightened

■ Aluminum wheel precautions (if equipped)

● Use only Toyota wheel nuts and wrench designed for use with

your aluminum wheels.

● When rotating, repairing or changing your tires, check that the

wheel nuts are still tight after driving 1000 miles (1600 km).

● Be careful not to damage the aluminum wheels when using

tire chains.

● Use only Toyota genuine balance weights or equivalent and a

plastic or rubber hammer when balancing your wheels.

407

4-3. Do-it-yourself maintenance

■When replacing wheels

The wheels of your Toyota are equipped with tire pressure warning valves and transmitters that allow the tire pressure warning system to provide advanced warning in the event of a loss in tire inflation pressure. Whenever wheels are replaced, the tire pressure warning valves and transmitters must be installed. (→P. 396)

CAUTION

■When replacing wheels

●Do not use wheels that are a different size from those recommended in

the Owner’s Manual, as this may result in loss of handling control.

●Never use an inner tube in a leaking wheel which is designed for a tubeless tire. Doing so may result in an accident, causing death or seri- ous injury.

■When installing the wheel nuts

Tapered portion

facing

tapered ends

●Be sure to install the wheel nuts with the inward. Installing the nuts with the tapered ends facing outward can cause the wheel to break and eventually cause the wheel to come off while driving, which could lead to an accident resulting in death or serious injury.

●Never use oil or grease on the wheel bolts or wheel nuts.

Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. In addition, the oil or grease can cause the wheel nuts to loosen and the wheel may fall off, causing an accident and resulting in death or serious injury. Remove any oil or grease from the wheel bolts or wheel nuts.

408

4-3. Do-it-yourself maintenance

NOTICE

■Replacing tire pressure warning valves and transmitters

●Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.

●Ensure that only Genuine Toyota wheels are used on your vehicle.

Tire pressure warning valves and transmitters may not work properly with non-genuine wheels.

409

4-3. Do-it-yourself maintenance Air conditioning filter

The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method

Turn the engine switch off.

Open the glove box. Slide off the damper.

Push in each side of the glove box to disconnect the upper claws.

Then disconnect the claws at the bottom and remove the glove box.

410

4-3. Do-it-yourself maintenance

Remove the filter case.

■ Replacement method

Remove the air conditioning filter and replace it with a new one.

The “↑UP” marks shown on the filter should be pointing up.

■Checking interval

Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

■If air flow from the vents decreases dramatically

The filter may be clogged. Check the filter and replace if necessary.

411

4-3. Do-it-yourself maintenance

NOTICE

■When using the air conditioning system Make sure that a filter is always installed. Using the air conditioning system without a filter may cause damage to the system.

412

4-3. Do-it-yourself maintenance Key battery

Replace the battery with a new one if it is discharged. ■ You will need the following items:

● Small Phillips-head screwdriver ● Lithium battery CR2016

■ Replacing the battery

Remove the screw and cover. Push the cover in the arrow direction.

Remove the module.

Open the case cover using a coin protected with tape etc. and remove the depleted bat- tery.

Insert a new battery with the “+” terminal facing up.

413

4-3. Do-it-yourself maintenance

■If the key battery is discharged

The following symptoms may occur. ●The wireless remote control will not function properly. ●The operational range is reduced.

■Use a CR2016 lithium battery

●Batteries can be purchased at your Toyota dealer, jewelers, or camera

stores.

●Replace only with the same or equivalent type recommended by your

Toyota dealer.

●Dispose of used batteries according to the local laws.

CAUTION

■Removed battery and other parts

Keep away from children. These parts are small and if swallowed by a child, they can cause choking. Failure to do so could result in death or serious injury.

NOTICE

■For normal operation after replacing the battery

Observe the following precautions to prevent accidents. ●Always work with dry hands.

Moisture may cause the battery to rust.

●Do not touch or move any other components inside the remote control. ●Do not bend either of the battery terminals.

414

4-3. Do-it-yourself maintenance Checking and replacing fuses

If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as necessary.

Turn the engine switch off. The fuses are located in the following places. To check the fuses, follow the instructions below.

■ Engine compartment

Type A

Push the tab in and lift the lid off.

Type B (if equipped)

Push the tab in and lift the lid off.

415

4-3. Do-it-yourself maintenance

■ Under the instrument panel

Remove the lid.

After a system failure, see “Fuse layout and amperage rat- ings” (→P. 419) for details about which fuse to check.

416

4-3. Do-it-yourself maintenance

Remove the fuse with the pull- out tool.

417

4-3. Do-it-yourself maintenance

Check if the fuse has blown.

Type A

Type B

Type C

418

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid.

Normal fuse Blown fuse Replace it with one of an appropriate amperage rating. The amperage rating can be found on the fuse box lid

4-3. Do-it-yourself maintenance

Fuse layout and amperage ratings

■ Engine compartment

Type A

Type B (if equipped)

419

4-3. Do-it-yourself maintenance

Fuse SPARE SPARE TOWING TAIL RR FOG

5 OFFROAD LP

10 A 15 A 15 A 10 A 15 A

STOP

10 A

DEICER AUX LP TOWING BRK

10 OBD

20 A 15 A 30 A 7.5 A

11 HEAD (LO RH)

10 A

12 HEAD (LO LH)

13 HEAD (HI RH) 14 HEAD (HI LH)

15 EFI NO.2

16

INJ

17 DRL

420

10 A

10 A 10 A

10 A

10 A

7.5 A

Ampere

Circuit

Spare fuse Spare fuse Trailer lights No circuit Offroad lamp Stop lights, high mounted stop- light, anti-lock brake system, trac- tion control system, active traction control system, vehicle stability control system, AUTO LSD system, multiport fuel injection system/ sequential multiport fuel injection system, shift lock system No circuit Driving lamp No circuit On-board diagnosis system Right-hand headlight (low beam)*1
Right-hand headlight*2
Left-hand headlight (low beam)*1
Left-hand headlight*2
Right-hand headlight (high beam)*1
Left-hand headlight (high beam)*1
Multiport fuel injection system/ sequential multiport fuel injection system Multiport fuel injection system/ sequential multiport fuel injection system Daytime running light system

4-3. Do-it-yourself maintenance

Fuse 18 DEFOG

19 DEFOG NO.2

20 DOME

21 RADIO NO.1

22 ECU-B

23 ALT-S 24 AI-VSV 25 HORN

26 A/F HEATER

27 TRN-HAZ

28 ETCS

29 EFI

30 TOWING NO.2

31 DR/LCK

32 TOWING 33 RADIO NO.2

Ampere

Circuit

30 A

10 A

10 A

20 A

10 A

7.5 A 10 A 10 A

15 A

15 A

10 A

20 A

30 A

20 A

15 A 20 A

Rear window defogger Multiport fuel injection system/ sequential multiport fuel injection system Interior light, personal lights, engine switch light, clock, acces- sory meter, meter and gauge Audio system Air conditioning system, multiplex communication system, SRS air- bag system, front passenger occu- pant classification system Charging system No circuit Horn Multiport fuel injection system/ sequential multiport fuel injection system Turn signal lights, emergency flashers Multiport fuel injection system/ sequential multiport fuel injection system, electronic throttle control system EFI NO.2, multiport fuel injection system/sequential multiport fuel injection system No circuit Door lock system, multiplex com- munication system Towing converter Audio system

421

Ampere

Circuit

No circuit ACC, ECU-IG, IG1, RR WSH, FR WIP-WSH, 4WD/DIFF and STA TAIL, PWR OUTLET, POWER Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, active traction control system, AUTO LSD system IGN and GAUGE, multiport fuel injection system/sequential multi- port fuel injection system, starting system Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, active traction control system, AUTO LSD system AM1, 400W INV, DEFOG, DEFOG NO.2, STOP, OBD, J/B, TOWING TAIL, AUX LP and OFFROAD LP Air conditioning system Power outlet

4-3. Do-it-yourself maintenance

Fuse 34 AIR PMP

35 AM1

36

J/B

37 ABS MTR

38 AM2

50 A

50 A

50 A

40 A

30 A

39 ABS SOL

30 A

40 ALT

41 HEATER 42
400W INV

120 A

60 A 80 A

*1: Vehicles with daytime running light *2: Vehicles without daytime running light

422

4-3. Do-it-yourself maintenance

■ Under the instrument panel

6 7 8

10 11

12

Fuse

Ampere

Circuit

IGN

10 A

2 GAUGE

FR WIP-WSH

4WD/DIFF

PWR OUTLET

RR WSH

7.5 A 30 A

20 A

15 A

15 A

Multiport fuel injection system/ sequential multiport fuel injection system, anti-lock brake system, vehicle stability control system, traction control system, active trac- tion control system, AUTO LSD system, SRS airbag system, front passenger occupant classification system Meter and gauge Windshield wipers and washer Four-wheel drive system, rear dif- ferential lock system Power outlet Rear window wiper and washer, multiplex communication system

423

4-3. Do-it-yourself maintenance

Fuse

Ampere

Circuit

ECU-IG

10 A

IG1

15 A

STA

10 TAIL

11 ACC

12 POWER

7.5 A

10 A

7.5 A

30 A

Anti-lock brake system, vehicle sta- bility control system, traction con- trol system, active traction control system, AUTO LSD system, cruise control system, back door lock sys- tem, shift lock system, multiplex communication system, tire pres- sure warning system Turn signal lights, air conditioning system, charging system, clutch start cancel switch, anti-lock brake system, traction control system, active traction control system, vehi- cle stability control system, AUTO LSD system, back-up lights, intui- tive parking assist, rear differential lock system, power outlet, acces- sory meter, meter and gauge, rear view monitor system Starting system, clutch start cancel switch, power outlet Tail lights, license plate lights, park- ing lights, instrument panel light control, illuminations Shift lock system, outside rear view mirrors, audio system, power out- let, clock, accessory meter, multi- plex communication system Power windows

424

4-3. Do-it-yourself maintenance

■After a fuse is replaced

●If the lights do not turn on even after the fuse has been replaced, a bulb

may need replacement. (→P. 426)

●If the replaced fuse blows again, have the vehicle inspected by your

Toyota dealer.

■If there is an overload in the circuits

The fuses are designed to blow, protecting the wiring harness from damage.

CAUTION

■To prevent system breakdowns and vehicle fire

Observe the following precautions. Failing to do so may cause damage, and possibly a fire or injury. ●Never use a fuse of a higher amperage rating than indicated, or use any

other object in place of a fuse.

●Always use a genuine Toyota fuse or equivalent.

Never replace a fuse with a wire, even as a temporary fix. This can cause extensive damage or even fire.

●Do not modify the fuse or the fuse box.

NOTICE

■Before replacing fuses

Have the cause of electrical overload determined and repaired by your Toy- ota dealer as soon as possible.

425

4-3. Do-it-yourself maintenance Light bulbs

You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. ■ Prepare a replacement light bulb.

Check the wattage of the light bulb being replaced. (→P. 492)

■ Front bulb locations

Headlights and daytime running lights (if equipped)

Front turn signal/parking and front side marker lights

426

4-3. Do-it-yourself maintenance

■ Rear bulb locations

Stop/tail and rear side marker lights

Back-up lights

Rear turn signal lights

License plate lights

Replacing light bulbs

■ Headlights and daytime running lights (if equipped) Unplug the connector.

427

4-3. Do-it-yourself maintenance

Remove the rubber cover.

Release spring.

the bulb

retaining

Remove the bulb.

To install a new bulb, align the tabs of the bulb with the cutouts of the mounting hole.

428

4-3. Do-it-yourself maintenance

■ Front turn signal/parking and front side marker lights

Turn the bulb base counterclock- wise.

Remove the light bulb.

429

4-3. Do-it-yourself maintenance

■ Back-up lights, stop/tail and rear side marker and rear turn

signal light bulbs

● Removing the sub woofer speaker (vehicles with sub woofer)

Remove the speaker cover.

Remove the cover.

Installing the sub woofer speaker (→P. 433)

Remove the sub woofer speaker.

Disconnect the connectors. Remove the 4 screws and the sub woofer speaker.

430

4-3. Do-it-yourself maintenance

● Removing the back-up, stop/tail and rear side marker and rear turn

signal light bulbs

Open the back door and remove the cover.

Using a flathead screwdriver or equivalent which is wrapped with a cloth.

Turn the bulb bases counter- clockwise.

Back-up light Rear turn signal light Stop/tail and rear side marker lights

Remove the light bulb.

Back-up light Rear turn signal light Stop/tail and rear side marker lights

431

4-3. Do-it-yourself maintenance

■ License plate lights

Remove the screws and cover.

Remove the light bulb.

■ Lights other than the above

If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. • Outside rear view mirror illumination lights (if equipped) • High mounted stoplight

432

4-3. Do-it-yourself maintenance

■Condensation build-up on the inside of the lens

Contact your Toyota dealer for more information in the following situations. Temporary condensation build-up on the inside of the headlight lens does not indicate a malfunction. ●Large drops of water are built up on the inside of the lens. ●Water has built up inside the headlight.

■LED high mounted stoplight

The high mounted stoplight consists of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced.

■Installing the sub woofer speaker (vehicles with sub woofer)

Install the rubber inside the panel as shown in the illustration.

CAUTION

■Replacing light bulbs

●Turn off the headlights. Do not attempt to replace the bulb immediately

after turning off the headlights. The bulbs become very hot and may cause burns.

●Do not touch the glass portion of the light bulb with bare hands. Hold the

bulb by the plastic or metal portion. If the bulb is scratched or dropped it may blow out or crack.

●Fully install light bulbs and any parts used to secure them. Failing to do so may result in heat damage, fire, or water entering the headlight unit. This may damage the headlights or cause condensation to build up on the lens.

■To prevent damage or fire

Make sure bulbs are fully seated and locked.

433

4-3. Do-it-yourself maintenance

434

5-1. Essential information Emergency flashers

Use the emergency flashers if the vehicle malfunctions or is involved in an accident.

Press the switch to flash all the turn signal lights. To turn them off, press the switch once again.

NOTICE

■To prevent battery discharge

Do not leave the emergency flashers on longer than necessary when the engine is not running.

436

5-1. Essential information If your vehicle needs to be towed

If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or a commercial towing service, using a lift-type truck or a flat bed truck. Use a safety chain system for all towing, and abide by all state/pro- vincial and local laws. The wheels and axle on the ground must be in good condition. If they are damaged, use a towing dolly or flat bed truck.

Before towing

The following may indicate a problem with your transmission. Contact your Toyota dealer before towing. ● The engine is running, but the vehicle will not move. ● The vehicle makes an abnormal sound.

Emergency towing

If a tow truck is not available, in an emergency your vehicle may be temporarily towed using a cable or chain secured to the emergency towing eyelet. This should only attempted on hard, surfaced roads for short distances at low speeds. A driver must be in the vehicle to steer and operate the brakes. The vehicle’s wheels, drive train, axles, steering and brakes must be in good condition.

Towing eyelet

437

5-1. Essential information

■Emergency towing procedure

The engine switch must be in the ACC (engine off) or the ON (engine running) position. 4WD models with an automatic transmission: Shift the front-wheel drive control lever in H2. 4WD models with a manual transmission: Unlock the center differ- ential. Put the shift lever in N. Release the parking brake.

CAUTION

■Caution while towing

●Use extreme caution when towing the vehicle.

Avoid sudden starts or erratic driving maneuvers which would place excessive stress on the emergency towing eyelet and the cables or chains. Always be cautious of the surroundings and other vehicles while towing.

●If the engine is not running, the power assist for the brakes and steering

will not function, making steering and braking more difficult.

NOTICE

■To prevent causing serious damage to the transmission

(vehicles with an automatic transmission) Never tow this vehicle from the rear with the four wheels on the ground. This may cause serious damage to the transmission.

■Emergency towing eyelet precautions

●Before emergency towing, check that the eyelet is not broken or damaged. ●Fasten the towing cable or chain securely to the eyelet. ●Do not jerk the eyelet. Apply steady and even force. ●To avoid damaging the eyelet, do not pull from the side or at a vertical

angle. Always pull straight ahead.

438

5-1. Essential information

Towing with a sling-type truck

NOTICE

■To prevent body damage

Do not tow with a sling-type truck, either from the front or rear.

Towing with a wheel lift-type truck from the front

Use a towing dolly under the rear wheels.

NOTICE

■To prevent causing serious damage to the transmission

Never tow this vehicle wheels on the ground.

439

5-1. Essential information

Towing with a wheel lift-type truck from the rear

2WD models

Turn the engine switch to the ACC position.

4WD models

Vehicles with a manual transmis- sion: Use a towing dolly under the front wheels. Vehicles with an automatic trans- mission: When not using a tow- ing dolly, turn the engine switch to the ACC position, shift the shift lever to N and shift the front- wheel drive control lever in H2.

NOTICE

■To prevent causing serious damage to the transmission (4WD models)

Never tow this vehicle wheels on the ground.

■To prevent damaging the vehicle

●Do not tow the vehicle with the key removed or in the LOCK position.

The steering lock mechanism is not strong enough to hold the front wheel straight.

●When raising the vehicle, ensure adequate ground clearance for towing at the opposite end of the raised vehicle. Without adequate clearance, the vehicle could be damaged while being towed.

440

Using a flat bed truck

Front

5-1. Essential information

If your Toyota is transported by a flat bed truck, it should be tied down at the locations shown in the illustration.

If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45°. Do not overly tighten the tie downs or the vehicle may be damaged. Apply the parking brake firmly.

441

5-1. Essential information If you think something is wrong

If you notice any of the following symptoms, your vehicle probably needs adjustment or repair. Contact your Toyota dealer as soon as possible. ■ Visible symptoms

● Fluid leaks under the vehicle

(Water dripping from the air conditioning after use is normal.)

● Flat-looking tires or uneven tire wear ● Engine coolant temperature gauge needle continually points

higher than normal

● Voltmeter continually points higher or lower than normal.

■ Audible symptoms

● Changes in exhaust sound ● Excessive tire squeal when cornering ● Strange noises related to the suspension system ● Pinging or other noises related to the engine

■ Operational symptoms

● Engine missing, stumbling or running rough ● Appreciable loss of power ● Vehicle pulls heavily to one side when braking ● Vehicle pulls heavily to one side when driving on a level road ● Loss of brake effectiveness, spongy feeling, pedal almost

touches the floor

442

5-1. Essential information Fuel pump shut off system

To minimize the risk of fuel leakage when the engine stalls or an air- bag inflates upon collision, the fuel pump shut off system stops sup- plying fuel to the engine.

Follow the procedure below to restart the engine after the system is activated.

Turn the engine switch to the ACC or LOCK position. Restart the engine.

NOTICE

■Before starting the engine

Inspect the ground under the vehicle. If you find that fuel has leaked onto the ground, the fuel system has been damaged and is in need of repair. Do not restart the engine.

443

5-2. Steps to take in an emergency If a warning light turns on or a warning buzzer sounds...

Calmly perform the following actions if any of the warning lights turn on or flash. If a light turns on or flashes, but then turns off, this does not necessarily indicate a malfunction in the system.

Stop the vehicle immediately. Continuing to drive the vehicle may be dangerous.

The following warning indicates a possible problem in the brake sys- tem. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Brake system warning light • Low brake fluid • Malfunction in the brake system This light also comes on when the parking brake is not released. If the light turns off after the parking brake is fully released, the system is operating nor- mally.

(U.S.A.)

(Canada)

444

5-2. Steps to take in an emergency

Stop the vehicle immediately.

The following warnings indicate the possibility of damage to the vehi- cle that may lead to an accident. Immediately stop the vehicle in a safe place and contact your Toyota dealer.

Warning light

Warning light/Details

Charging system warning light Indicates a malfunction in the vehicle’s charging sys- tem.

Low engine oil pressure warning light Indicates that the engine oil pressure is too low*.

*: The light may come on when the oil level is extremely low. It is not designed to indicate low oil level, and the oil level must be checked using the engine oil level dipstick.

Have the vehicle inspected immediately.

Failing to investigate the cause of the following warnings may lead to the system operating abnormally and possibly cause an accident. Have the vehicle inspected by your Toyota dealer immediately.

Warning light

Warning light/Details

Malfunction indicator lamp Indicates a malfunction in: • The electronic engine control system; • The electronic throttle control system; • The electronic automatic transmission control sys- tem; or • Emission control system.

(U.S.A.)

(Canada)

445

5-2. Steps to take in an emergency

Warning light

Warning light/Details

SRS warning light Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system.

ABS warning light Indicates a malfunction in: • The ABS; or • The brake assist system.

(U.S.A.)

(Canada)

Slip indicator The indicator comes on to indicate a malfunction in: • The VSC; • The TRAC (TRC); or • The active traction control system (if equipped); or • The AUTO LSD system (2WD models). Automatic transmission fluid temperature warn- ing light • Comes on: Indicates that the automatic transmission fluid temperature is too high. • Flashes: Indicates a malfunction in the automatic transmission system.

Unengaged “Park” warning light Malfunction in the transmission “Park” mechanism.

Cruise control indicator light (if equipped) Indicates a malfunction in the cruise control system.

(Automatic transmis-

sion vehicles)

(Automatic transmis-

sion vehicles)

(Flashes)

446

5-2. Steps to take in an emergency

Follow the correction procedures.

After taking the specified steps to correct the suspected problem, check that the warning light turns off.

Warning light

Warning light/Details

Correction procedure

Open door warning light Indicates that a door, back door or glass hatch is not fully closed. Driver’s seat belt reminder light (warning buzzer)*1
Warns the driver to fas- ten his/her seat belt. Front passenger’s seat belt reminder light (warning buzzer)*2
Warns the front passen- ger to fasten his/her seat belt.

Check that all doors and glass hatch are closed.

Fasten the seat belt.

Fasten the seat belt.

(On the instrument

cluster)

(On the center

panel)

447

5-2. Steps to take in an emergency

Warning light

Warning light/Details

Correction procedure

Tire pressure warning light When the light comes on: Low tire inflation pres- sure such as • Natural causes (→P. 450) • Flat tire (→P. 454)

When the light comes on after blinking for 1 minute: Malfunction in the tire pressure warn- ing system (→P. 451) Low fuel level warning light Low level of fuel. Low washer fluid warn- ing light Low level of washer fluid.

Adjust the tire inflation pressure (including the spare tire) to the specified level. The light will turn off after a few minutes. In case the light does not turn off even if the tire inflation pressure is adjusted, have the system checked by your Toyota dealer. Have the system checked by your Toyota dealer.

Refuel the vehicle.

Fill the tank.

(Canada)

448

5-2. Steps to take in an emergency

Warning light

Warning light/Details Maintenance required reminder light Indicates that mainte- nance is required accord- ing to the driven distance on the maintenance schedule.*3
Illuminates for about 3 seconds and then flashes for about 15 seconds approximately 4500 miles (7200 km) after the main- tenance data has been reset. Comes on and remains on if the distance driven exceeds 5000 miles (8000 km) after the maintenance data has been reset. (The indicator will not work properly unless the main- tenance data has been reset.) *1: Driver’s seat belt reminder:

(U.S.A.)

Correction procedure

If necessary, perform maintenance.

Perform the necessary maintenance. Please reset the mainte- nance data after the maintenance is per- formed. (→P. 371)

The driver’s seat belt reminder sounds to alert the driver that his or her seat belt is not fastened. Once the engine switch is turned to the ON or START position, the buzzer sounds for 6 seconds. If the vehicle has reached a speed of at least 12 mph (20 km/h), the buzzer sounds intermittently for 10
seconds. Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 more seconds.

*2: Front passenger’s seat belt reminder:

The front passenger’s seat belt reminder sounds to alert the front passenger that his or her seat belt is not fastened. The buzzer sounds intermittently for 10 seconds after the vehicle has reached a speed of at least 12 mph (20 km/ h). Then, if the seat belt is still unfastened, the buzzer will sound in a different tone for 20 more seconds.

449

5-2. Steps to take in an emergency

*3: Refer to the separate “Scheduled Maintenance Guide” or “Owner’s Manual

Supplement” for the maintenance interval applicable to your vehicle.

■Key reminder buzzer

The buzzer indicates that the key has not been removed (with the engine switch in the ACC or LOCK position and the driver’s door opened).

■If the malfunction indicator lamp comes on while driving

First check the following: