2011 Toyota FJ Cruiser Owners Manual

offers greater durability and consumes less electricity, so it can help improve fuel economy.

n Automatic light off system

l When the headlights come on: The headlights and tail lights turn off 30
seconds after all doors and glass hatch are closed with the engine switch turned to the ACC or LOCK position. (The lights turn off immediately if the LOCK button on the wireless remote control is pressed twice after all doors are locked.)

l When only the tail lights come on: The tail lights turn off automatically with the engine switch turned to the ACC or LOCK position and the driver’s door is opened.

If the driver’s door is kept open, the lights automatically turn off after 30 min- utes. To turn the lights on again, turn the engine switch to the ON position, or turn the headlight switch off once and then back to the

or n Customization that can be configured at Toyota dealer

position.

Settings (automatic light off system) can be changed. (Customizable features →P. 493)

NOTICE

n To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

144

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation (when INT is selected).

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation

speed windshield

Decreases the intermittent windshield wiper frequency Increases intermittent windshield wiper frequency

the

145

2-3. Operating the lights and wipers

Washer/wiper dual opera- tion Wipers will automatically oper- ate a couple of times after the washer squirts.

n The windshield wiper and washer can be operated when

The engine switch must be in the ON position.

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

n When a nozzle becomes blocked

In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged.

146

2

2-3. Operating the lights and wipers Rear window wiper and washer∗

Intermittent window wiper operation. The wiper operates 3 times at normal speed and then moves to intermittent mode. Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion The rear window wiper oper- ates while the washer squirts.

n The rear window wiper and washer can be operated when

l The engine switch must be in the ON position. l The glass hatch is closed.

NOTICE

n When the rear window is dry

Do not use the wipers, as they may damage the rear window.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the knob is continuously twisted upward or downward as far as it will go.

∗: If equipped 147

2-4. Using other driving systems Cruise control∗

Use the cruise control to maintain a set speed without depressing the accelerator pedal.

Indicator Cruise control switch

n Setting the vehicle speed

Press the ON-OFF button to activate the cruise control. Press the button again deactivate the cruise control.

to

Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set the speed.

148

∗: If equipped

2

2-4. Using other driving systems

n Adjusting the set speed

To change the set speed, operate the lever until the desired set speed is obtained.

Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direction. Large adjustment: Hold lever in the desired direction.

the

The set speed will be increased or decreased as follows: Fine adjustment: By approximately 1 mph (1.6 km/h) each time the lever is operated. Large adjustment: The set speed can be increased or decreased con- tinually until the lever is released.

149

2-4. Using other driving systems

n Canceling and resuming the constant speed control

Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual transmission only) is depressed. Pushing resumes speed control. Resuming is available when the vehicle speed is more than approximately 25 mph (40 km/ h).

lever up constant

the the

n Cruise control can be set when

l The shift lever is in the D or 4 range (vehicles with an automatic transmis-

sion).

l Vehicle speed is above approximately 25 mph (40 km/h).

n Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

n Automatic cruise control cancellation

Cruise control will stop maintaining the vehicle speed in any of the following situations. l Actual vehicle speed falls more than approximately 10 mph (16 km/h)

below the preset vehicle speed. At this time, the memorized set speed is not retained.

l Actual vehicle speed is below approximately 25 mph (40 km/h). l VSC is activated.

150

2

2-4. Using other driving systems

n If the cruise control indicator light flashes

Press the ON-OFF button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

CAUTION

n To avoid operating the cruise control by mistake

Switch the cruise control off using the ON-OFF button when not in use.

n Situations unsuitable for cruise control

In heavy traffic

Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. l On roads with sharp bends l On winding roads l On slippery roads, such as those covered with rain, ice or snow l On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill

l When your vehicle is towing a trailer or during emergency towing

151

2-4. Using other driving systems Intuitive parking assist∗

The intuitive parking assist assists the driver by communicating the distance to obstacles measured by the sensors via the buzzer when parallel parking or maneuvering into a garage. Always check the sur- rounding area when using this system. n Back sensors

These sensors detect obsta- cles behind the vehicle.

152

∗: If equipped

2

n Intuitive parking assist switch

2-4. Using other driving systems

ON/OFF When on, the buzzer sounds to inform the driver that the system is operational. At this time, the indicator will come on. Press the switch to switch the ON/OFF mode.

The distance and buzzer

When a sensor detects an obstacle, the buzzer sounds.

Distance shown as Buzzer

4.9 to 3.3 ft. (150 to 100 cm) Medium

3.3 to 1.6 ft. (100 to 50 cm) Fast

1.6 ft. (50 cm) Continuous

153

2-4. Using other driving systems

Sensors that operate and detection range

The following diagrams show the sensor detection range. Note that sensors may not be able to detect obstacles that are extremely close to the vehicle. n Detection range of the sensors

Approx. 4.9 ft. (150 cm) The diagram shows the detection range of the sensors. Note that the sensors may not be able to detect are extremely close to the vehicle. The range of the sensors may change depending on the shape of the object etc.

obstacles

that

154

2-4. Using other driving systems

n The intuitive parking assist system can be operated when

l The engine switch is at the ON position. l The shift lever is in R.

n Sensor detection information

l Certain vehicle conditions and the surrounding environment may affect the ability of a sensor to correctly detect an obstacle. Particular instances where this may occur are listed below. • There is dirt, snow or ice on a sensor. • A sensor is frozen. • A sensor is covered in any way. • The vehicle is leaning considerably to one side. • On an extremely bumpy road, on an incline, on gravel, or on grass. • The vicinity of the vehicle is noisy due to vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.

• There is another vehicle equipped with parking assist sensors in the

vicinity.

• A sensor is coated with a sheet of spray or heavy rain. • The vehicle is equipped with a fender pole or radio antenna. • A bumper or sensor receives a strong impact. • The vehicle is approaching a tall or right-angled curb. • In harsh sunlight or intense cold weather. • The area directly under the bumpers is not detected.

Objects lower than the sensors or thin stakes etc. may be detected ini- tially, but as they draw closer, they may cease to be detected.

• A towing hitch is mounted to the vehicle. • A non-genuine Toyota suspension (lowered suspension etc.) is

installed.

• When attaching a two-way radio antenna. • When a towing eyelet is mounted on your vehicle. • When the bumper is damaged.

In addition to the examples above, there are instances in which, because of their shapes, signs and other objects may be judged by a sensor to be closer than they are.

155

2-4. Using other driving systems

l The shape of the obstacle may prevent a sensor from detecting it. Pay

particular attention to the following obstacles: • Wires, fences, ropes, etc. • Cotton, snow and other materials that absorb radio waves • Sharply-angled objects • Low obstacles • Tall obstacles with upper sections projecting outwards in the direction

of your vehicle

• A person near the vehicle (depending on the type of clothes worn) • When the bumper is damaged.

n Certification (Canada only)

This ISM device complies with Canadian ICES-001.

CAUTION

n Caution when using the intuitive parking assist

Observe the following precautions. Failure to do so may result in the vehicle being unable to be driven safely and possibly cause an accident. l Do not use the sensor at speeds in excess of 6 mph (10 km/h). l Do not attach any accessories within the sensor range.

NOTICE

n Notes when washing the vehicle

Do not apply intensive bursts of water or steam to the sensor area. Doing so may result in the sensor malfunctioning.

156

2-4. Using other driving systems Rear view monitor system∗

The rear view monitor system assists the driver by displaying an image of the area behind the vehicle. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror.

The rear view image is dis- played on the inside rear view mirror when the shift lever is in the R.

The screen is turned off if any one of the following conditions are met: • The shift lever is shifted out

of R

• The back door opens • The screen remains on for 5

minutes

Automatic transmission Manual transmission Screen

n The rear view monitor system can be operated when

The shift lever is in R, the back door is fully closed and the engine switch is ON.

∗: If equipped 157

2-4. Using other driving systems

n Switching the screen ON/OFF mode

When the screen is displayed, press the AUTO button on the inside rear view mir- ror to switch the screen ON/OFF mode. Screen ON mode: Green indicator comes on. Screen OFF mode: Orange comes on.

indicator

The auto anti-glare inside rear view mir- ror will revert to the screen ON mode each time the engine switch is turned on.

The area covered by the camera is lim- ited. Objects that are close to either corner of the bumper or underneath the spare tire cannot be seen on the screen. The area displayed on the screen may vary according to vehicle orientation or road conditions.

n Displayed area

Corners of bumper

158

2

2-4. Using other driving systems

n Rear view monitor system camera

In the following cases, it may become dif- ficult to see the images on the screen, even when the system is functioning cor- rectly.

l The vehicle is in a dark area, such

as at night.

l The temperature near the lens is

extremely high or low.

l Water droplets are on the camera lens or humidity is high, such as when it rains.

l Foreign matter, such as snow or

mud, adheres to the camera lens.

l The sun or headlights are shining

directly into the camera lens.

l A bright object such as a white wall is reflected in the mirror surface over the monitor.

l The camera has scratches or dirt on

it.

n Smear effect

light, such as sunlight If a bright reflected off the vehicle body, is picked up by the camera, a smear effect* char- acteristic to the camera may occur. *: Smear effect: A phenomenon that occurs when a bright light is picked up by the camera; when transmitted by light source appears to have a vertical streak above and below it.

the camera,

the

n Flicker effect

When the camera is used under fluorescent lights, sodium lights, mercury lights etc., the lights and the illuminated areas may appear to flicker.

159

2-4. Using other driving systems

CAUTION

n When using the rear view monitor system, observe the following pre- cautions to avoid an accident that could result in death or serious inju- ries. l Never depend solely on the monitor system when reversing. l Always check visually and with the mirrors to confirm your intended path is

clear.

l Depicted distances between objects and flat surfaces differ from actual

distances.

n Conditions which may affect the rear view monitor system

If the back of the vehicle has been hit, the camera’s position and mounting angle may have changed. Have the vehicle inspected by your Toyota dealer.

l Rapid temperature changes, such as when hot water is poured on the

vehicle in cold weather, may cause the system to function abnormally. If the camera lens is dirty, it cannot transmit a clear image. Rinse with water and wipe with a soft cloth. If extremely dirty, wash with a mild cleanser and rinse.

l The displayed image may be darker and moving images may be slightly

distorted when the system is cold.

NOTICE

l As the camera has a water proof construction, do not detach, disassemble

or modify it. This may cause incorrect operation. If the camera lens becomes dirty, it cannot transmit a clear image. If water droplets, snow, or mud adhere to the lens, rinse with water and wipe with a soft cloth. If the lens is extremely dirty, wash it with a mild cleanser and rinse.

l Do not allow organic solvent, car wax, window cleaner or glass coat to

adhere to the camera. If this happens, wipe it off as soon as possible.

l When washing the vehicle, do not apply intensive bursts of water to the camera or camera area. Doing so may result in the camera malfunction- ing.

160

2-4. Using other driving systems Four-wheel drive system (4WD models with a manual transmission)

Use the four-wheel drive control lever to select the following transfer modes.

The center differential lock indicator comes on when the LL or HL mode is selected.

H (high speed position) Use this for normal driving on dry hard-surfaced roads. This position gives greater economy, quietest ride and least wear. HL (high speed position, center differential locked) Use this for driving only on tracks that permit the tires slide, like off- road, icy or snow-covered roads. N (neutral position) No power is delivered to the wheels. The vehicle must be stopped. LL (low speed position, center differential locked) Use this for maximum power and traction. Use “LL” for climbing or descending steep hills, off-road driving, and hard pulling in sand, mud or deep snow.

161

2-4. Using other driving systems

n Shifting between H and HL

l You need not to depress the clutch pedal.

If the center differential lock indicator does not come on when you shift from H to HL, drive straight ahead while accelerating or decelerating. If the center differential lock indicator does not go off when you shift from HL to H, drive straight ahead while accelerating or decelerating, or drive in reverse.

n Shifting from HL to LL

Stop the vehicle or reduce your speed to less than 5 mph (8 km/h). Depress the clutch pedal and move the four-wheel drive control lever.

n Shifting from LL to HL

Depress the clutch pedal and move the four-wheel drive control lever.

n Shifting to LL

VSC is automatically turned off.

CAUTION

n Caution while driving

Avoid turning suddenly while the center differential is locked. If you do turn suddenly, the difference in turning speeds between the front and rear wheels may have a similar effect to braking, thus making driving difficult.

162

2-4. Using other driving systems

NOTICE

n To prevent damage to the center differential

l For normal driving on dry and hard surface roads, unlock the center differ-

ential.

l Shift to H after the wheels are out of the ditch or off the slippery or bumpy

surface.

l Do not shift to any position when the vehicle is cornering or when its

wheels spinning freely off the ground.

n Shifting from H to HL while driving

Never operate the four-wheel drive control lever if the wheels are slipping. Stop the slipping or spinning before shifting.

163

2-4. Using other driving systems Four-wheel drive system (4WD models with an automatic transmission)

Use the front-wheel drive control lever to select the following trans- fer modes.

The four-wheel drive indicator comes on when the H4, N or L4 mode is selected.

H2 (high speed position, two-wheel drive) Use this for normal driving on dry hard-surfaced roads. This position gives greater economy, quietest ride and least wear. H4 (high speed position, four-wheel drive) Use this for driving only on tracks that permit the tires slide, like off- road, icy or snow-covered roads. This position provides greater traction than two-wheel drive. N (neutral position) No power is delivered to the wheels. The vehicle must be stopped. L4 (low speed position, four-wheel drive) Use this for maximum power and traction. Use “L4” for climbing or descending steep hills, off-road driving, and hard pulling in sand, mud or deep snow.

164

2

2-4. Using other driving systems

n Shifting between H2 and H4

l Reduce your speed to less than 50 mph (80 km/h) and shift the front-

wheel drive control lever from H2 to H4. If you have trouble shifting in cold weather, reduce your speed or stop the vehicle. If the four-wheel drive indicator does not go off when you shift from H4 to H2, drive straight ahead while accelerating or decelerating, or drive in reverse.

n Shifting between H4 and L4

Stop the vehicle, shift the shift lever to N and shift the front-wheel drive con- trol lever.

n Shifting to L4

VSC is automatically turned off.

n Four-wheel drive usage frequency

You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front drive components are lubricated.

165

2-4. Using other driving systems

CAUTION

n Caution while driving

l Never shift the front-wheel drive control lever from H2 to H4 if the wheels

are slipping. Stop the slipping or spinning before shifting.

l For normal driving on dry and hard surface roads, use H2 position. Driving on dry and hard surface roads in H4 or L4 position may cause drive com- ponent oil leakage, seizure, or other problems resulting in an accident. Further, it may cause tire wear and increased fuel consumption.

l Avoid turning suddenly in H4 or L4 position. If you do turn suddenly, the difference in turning speeds between the front and rear wheels may have a similar effect to braking, thus making driving difficult.

l Securely shift the front-wheel drive control lever to H4 or L4. Otherwise, the transfer may disengage both the front and rear driveshafts from the powertrain and allow the vehicle to move regardless of the shift position. If this happens, the vehicle may be free to roll even if the automatic trans- mission is in P.

166

2

2-4. Using other driving systems Active traction control system∗

The active traction control system automatically helps prevent the spinning of 4 wheels when the vehicle is started or accelerated on slippery road surfaces. n System operation

Vehicles with an automatic transmission: Stop the vehicle, shift the shift lever to N and shift the front- wheel drive control lever into L4. Vehicles with a manual transmission: Stop the vehicle or reduce your speed to less than 5 mph (8
km/h). Depress the clutch pedal and shift the four-wheel drive control lever into LL.

Press the A-TRAC switch to activate the system.

At this time, the active traction control system indicator will come on. To cancel the system, push the switch again.

When the active traction control system is operating

If any of the drive wheels spins, the slip indicator flashes to indi- cate that the active traction con- trol system have been engaged.

∗: If equipped 167

2-4. Using other driving systems

n When the rear differential is locked (vehicles with the rear differential

lock system) The active traction control system is activated only when the vehicle speed is less than 4 mph (6 km/h).

n Sounds and vibrations caused by the active traction control system

l A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in the system.

l Vibrations may be felt through the vehicle body and steering. It may

occur when the system is operating.

n If the brake system overheats

The system will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.)

CAUTION

n The active traction control system may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the active traction control system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

168

2-4. Using other driving systems AUTO LSD system (2WD models)

The AUTO LSD system aids traction by using the traction control system to control engine performance and braking when one of the rear wheels begins to spin. The system should be used only when wheel spinning occurs in a ditch or rough surface. n System operation The system is activated when driving at a speed under 62 mph (100 km/h).

Press the VSC OFF switch to turn on the system.

At this time, the AUTO LSD and VSC OFF indicators will come on. To turn off the system, push the switch again.

When the AUTO LSD system is operating

If the rear wheels spin, the slip indicator flashes to indicate that the AUTO LSD system has con- trolled the spinning of the rear wheels.

169

2-4. Using other driving systems

n If the engine is turned off and restarted

The AUTO LSD system and the indicators are automatically turned off.

n Reactivation of the VSC system linked to vehicle speed

When the AUTO LSD system is turned on, the VSC system will turn on auto- matically if vehicle speed increases.

n If the brake system overheats

The system will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.) The system will be automatically restored after a short time.

CAUTION

n To avoid an accident

l Do not use the AUTO LSD system in conditions other than the above.

A much greater steering effort and more careful cornering control will be required.

l Do not drive with the AUTO LSD system continuously turned on.

170

2-4. Using other driving systems Rear differential lock system∗

The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a slippery or rugged surface. The rear differential lock system is effective in case one of the rear wheels is spinning.

Press the RR DIFF LOCK switch to lock the rear differen- tial.

At this time, the rear differential lock indicator will blink. Wait a few seconds for the system to complete operation. After the rear differential is locked, the indicator will stop blinking and remain on. To unlock the rear differential, push the switch again.

Using the rear differential lock system

Automatic transmission

4WD models: Before using the rear differential lock system. Stop the vehicle, shift the shift lever to N and shift the front- wheel drive control lever into L4 to see if this is sufficient. If this has no effect, additionally use the rear differential lock system. Be sure to stop the wheels. Press the RR DIFF LOCK switch. Gently depress the accelerator pedal. After the rear differential is locked, the indicator will come on.

Unlock the rear differential as soon as the vehicle moves. To unlock the rear differential, push the switch again.

∗: If equipped 171

2-4. Using other driving systems

Manual transmission

Before using the rear differential lock system. Stop the vehicle or reduce your speed to less than 5 mph (8
km/h). Depress the clutch pedal and shift the four-wheel drive control lever into LL to see if this is sufficient. If this has no effect, additionally use the rear differential lock system. Be sure to stop the wheels. Depress the clutch pedal. Press the RR DIFF LOCK switch. Slowly release the clutch pedal. After the rear differential is locked, the indicator will come on.

Unlock the rear differential as soon as the vehicle moves. To unlock the rear differential, push the switch again.

n Locking the rear differential

l When the rear differential is locked, VSC is automatically turned off.

(The rear differential lock and VSC OFF indicators will come on.)

l The following systems do not operate when the rear differential is locked. It is normal operation for the ABS warning light and VSC OFF indicator to be on at this time. • ABS • Brake assist system • VSC • TRAC (TRC)

n The rear differential lock is disengaged when

l Shift the four-wheel drive control lever to H or HL. (4WD models with a

manual transmission)

l Shift the front-wheel drive control lever to H2 or H4. (4WD models with

an automatic transmission)

Never forget to turn off the switch after using this feature.

n After unlocking the rear differential

Check that the indicator goes off.

172

2-4. Using other driving systems

CAUTION

n To avoid an accident

l Do not use the rear differential lock system except when wheel spinning occurs in a ditch or on a slippery or ragged surface. Large steering effort and careful cornering control will be required.

l Do not lock the rear differential until the wheels have stopped spinning.

Otherwise, the vehicle may move in an unexpected direction when the dif- ferential lock is engaged, resulting in an accident. This may also lead to possible damage to rear differential lock component parts.

l Do not drive over 5 mph (8 km/h) when the rear differential is locked. l Do not keep driving with the RR DIFF LOCK switch on.

173

2-4. Using other driving systems Clutch start cancel switch (vehicles with a manual transmission)

The switch allows the vehicle to be driven out of difficult situations by cranking the engine with the clutch engaged. Never use the switch for normal engine starting. Be sure to follow the starting procedure. (→P. 124)

Press the CLUTCH START CANCEL switch to cancel the clutch start system with the engine switch is turned to the ON position.

The indicator will come on when the clutch start system is canceled. The clutch start cancel switch turned off is automatically when is turned off.

the engine switch

n Clutch start system

The system is designed to keep the starter motor from operating if the clutch pedal is not depressed all the way down.

174

2

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. n ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

n Brake Assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

n VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

n TRAC/TRC (Traction Control)

Maintains drive power and prevents the rear wheels (2WD models) or all wheels (4WD models) from spinning when starting the vehicle or accelerating on slippery roads.

When VSC/TRAC (TRC) are operating

If the vehicle is in danger of slip- ping, or if the rear wheels (2WD models) or any of the drive wheels (4WD models) spins, the slip indicator flashes to indicate that VSC/TRAC (TRC) have been engaged.

175

2-4. Using other driving systems

To disable TRAC and/or VSC (2WD models)

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. n Turning off TRAC

n Turning off TRAC and VSC

Press the VSC OFF switch to turn off TRAC.

indicator will

The AUTO LSD come on. Push the switch again to turn the system back on.

Press the VSC OFF switch for more than 3 seconds while the vehicle is stopped to turn off both TRAC and VSC.

The VSC OFF and TRAC OFF indicators will come on. Push the switch again to turn both systems back on.

176

2-4. Using other driving systems

To disable TRAC (TRC) and/or VSC (H2 and H4 mode [automatic transmission] or H and HL mode [manual transmission] on 4WD models)

If the vehicle gets stuck in fresh snow or mud, TRAC (TRC) and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. n Turning off TRAC (TRC)

U.S.A. Canada

Press the VSC OFF switch to turn off TRAC (TRC).

The TRAC OFF (TRC OFF) indi- cator will come on. Push the switch again to turn the system back on.

n Turning off TRAC (TRC) and VSC

U.S.A. Canada

Press and hold the VSC OFF switch for more than 3 seconds while the vehicle is stopped to turn off both TRAC (TRC) and VSC.

The VSC OFF and TRAC OFF (TRC OFF) indicators will come on. Push the switch again to turn both systems back on.

177

2-4. Using other driving systems

n Automatic reactivation of TRAC (TRC) and VSC

Turning the engine switch off after turning off the TRAC (TRC) and VSC sys- tems will automatically re-enable them.

n Automatic VSC reactivation (2WD models)

If only the TRAC system is turned off, VSC OFF and AUTO LSD indicators turn on. The VSC system will turn on when the vehicle speed increases.

n Automatic TRAC (TRC) and VSC reactivation

If the TRAC (TRC) and VSC systems are turned off, the systems will not turn on, even when vehicle speed increases.

n Sounds and vibrations caused by the ABS, TRAC (TRC), VSC and

brake assist system l A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

l Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after the ABS is activated. • The brake pedal may move down slightly after the ABS is activated.

n If the brake system overheats

TRAC (TRC) will cease operation and a buzzer will sound to alert the driver. Stop the vehicle in a safe place. (There is no problem with continuing normal driving.)

178

2

2-4. Using other driving systems

CAUTION

n The ABS does not operate effectively when

l The limits of the gripping performance have been exceeded. l The vehicle hydroplanes while driving at high speed on the wet or slick

road.

n Stopping distance when the ABS is operating will exceed that of nor-

mal conditions The ABS is not designed to shorten the vehicle’s stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. l When driving on dirt, gravel or snow-covered roads l When driving with tire chains l When driving over bumps in the road l When driving over roads with potholes or roads with uneven roads

n When VSC is activated

The slip indicator flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator flashes.

n TRAC (TRC) may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if TRAC (TRC) is operating. Do not drive the vehicle in conditions where stability and power may be lost.

n Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the appro- priate tire pressure level. The ABS, VSC and TRAC (TRC) will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

n Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

179

2-5. Driving information Off-road precautions

This vehicle belongs to the utility vehicle class, which has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off-road applications.

Off-road vehicle feature

l Specific design characteristics give it a higher center of gravity than ordinary passenger cars. This vehicle design feature causes this type of vehicle to be more likely to rollover. And, utility vehicles have a significantly higher rollover rate than other types of vehi- cles.

l An advantage of the higher ground clearance is a better view of the

road allowing you to anticipate problems. It is not designed for cornering at the same speeds as ordinary passenger cars any more than low-slung sports cars designed to perform satisfactorily under off-road conditions. Therefore, sharp turns at excessive speeds may cause rollover.

180

2

2-5. Driving information

CAUTION

n Off-road vehicle precautions

Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle:

In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.

l Avoid sharp turns or abrupt maneuvers, if at all possible.

Failure to operate this vehicle correctly may result in loss of control or vehicle rollover causing death or serious injury.

l Loading cargo on the roof luggage carrier will make the center of the vehi- cle gravity higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneuvers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle correctly.

l Always slow down in gusty crosswinds. Because of its profile and higher center of gravity, your vehicle is more sensitive to side winds than an ordi- nary passenger car. Slowing down will allow you to have better control.

l When driving off-road or in rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.

l Do not drive horizontally across steep slopes. Driving straight up or straight down is preferred. Your vehicle (or any similar off-road vehicle) can tip over sideways much more easily than forward or backward.

181

2-5. Driving information

Off-road driving

When driving your vehicle off-road, please observe the following pre- cautions to ensure your driving enjoyment and to help prevent the closure of areas to off-road vehicles. l Drive your vehicle only in areas where off-road vehicles are permit-

ted to travel.

l Respect private property. Get owner’s permission before entering

private property.

l Do not enter areas that are closed. Honor gates, barriers and signs

that restrict travel.

l Stay on established roads. When conditions are wet, driving tech- niques should be changed or travel delayed to prevent damage to roads.

n Additional information for off-road driving

For owners in U.S. mainland, Hawaii and Puerto Rico:

To obtain additional information pertaining to driving your vehicle off-road, consult the following organizations. l State and Local Parks and Recreation Departments l State Motor Vehicle Bureau l Recreational Vehicle Clubs l U.S. Forest Service and Bureau of Land Management

182

2-5. Driving information

CAUTION

n Off-road driving precautions

Always observe the following precautions to minimize the risk of serious per- sonal injury or damage to your vehicle: l Drive carefully when off the road. Do not take unnecessary risks by driving

in dangerous places.

l Do not grip the steering wheel spokes when driving off-road. A bad bump could jerk the wheel and injure your hands. Keep both hands and espe- cially your thumbs on the outside of the rim.

l Always check your brakes for effectiveness immediately after driving in

sand, mud, water or snow.

l After driving through tall grass, mud, rock, sand, rivers, etc., check that there is no grass, bush, paper, rags, stone, sand, etc. adhering or trapped on the underbody. Clear off any such matter from the underbody. If the vehicle is used with these materials trapped or adhering to the underbody, a breakdown or fire could occur. In a rollover crash, an unbelted person is significantly more likely to die than a person wearing a seat belt. Therefore, the driver and all passengers should fasten their seat belts whenever the vehicle is moving.

l When driving off-road or in rugged terrain, do not drive at excessive speeds, jump, make sharp turns, strike objects, etc. This may cause loss of control or vehicle rollover causing death or serious injury. You are also risking expensive damage to your vehicle’s suspension and chassis.

183

2-5. Driving information

NOTICE

n To prevent the water damage

l Take all necessary safety measures to ensure that water damage to the

engine or other components does not occur.

l Water entering the engine air intake will cause severe engine damage. l Water entering the automatic transmission will cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ulti- mately damage.

l Water can wash the grease from wheel bearings, causing rusting and pre- mature failure, and may also enter the differentials, transmission and transfer case, reducing the gear oil’s lubricating qualities.

n When you drive through water

If driving through water, such as when crossing shallow streams, first check the depth of the water and the bottom of the river bed for firmness. Drive slowly and avoid deep water.

n Inspection after off-road driving

l Sand and mud that has accumulated in brake drums and around brake discs may affect braking efficiency and may damage brake system compo- nents.

l Always perform a maintenance inspection after each day of off-road driv- ing that has taken you through rough terrain, sand, mud, or water. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.

184

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. l Stow cargo and luggage in the luggage compartment whenever

possible.

l Be sure all items are secured in place. l Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

l For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) − (Total weight of occupants) Steps for Determining Correct Load Limit— (1)Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’s placard.

(2)Determine the combined weight of the driver and passengers that

will be riding in your vehicle.

(3)Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4)The resulting figure equals the available amount of cargo and lug-

gage load capacity. For example, if the “XXX” amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of available cargo and luggage load capacity is 650 lbs. (1400 − 750 (5 × 150) = 650 lbs.)

(5)Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

185

2-5. Driving information

(6)If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 1130 lb. (510
kg), the available amount of cargo and luggage load capacity will be as follows: 1130 lb. − 366 lb. = 764 lb. (510 kg − 166 kg = 344 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

764 lb. − 388 lb. = 376 lb. (344 kg − 176 kg = 168 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

186

2

2-5. Driving information

CAUTION

n Things that must not be carried in the luggage compartment

The following things may cause a fire if loaded in the luggage compart- ment. l Receptacles containing gasoline l Aerosol cans

n Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. l Do not place cargo or luggage in or on the following locations as the item may get under the clutch, brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Instrument panel • Dashboard • Auxiliary box or tray that has no lid

l Do not stack anything in the luggage compartment higher than the

seatbacks. Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

l Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

l Never allow anyone to ride in the luggage compartment. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious injury, in the event of sudden braking, sudden swerv- ing or an accident.

187

2-5. Driving information

CAUTION

n Capacity and distribution

l Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

l Even if the total load of occupant’s weight and the cargo load is less than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking control which may cause death or serious injury.

188

2

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. n Total load capacity: 1130 lb. (510 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

n Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. Even if the number of occupants are within the seating capacity, do not exceed the total load capacity. n Towing capacity: 5000 lb. (2270 kg)

Towing capacity means the maximum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

n Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

n Total load capacity and seating capacity

These details are also described on the tire and loading information label.(→P. 387)

CAUTION

n Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

189

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. n Pre-winter preparations

l Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine coolant • Washer fluid

l Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

l Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the rear tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. n Before driving the vehicle

Perform the following according to the driving conditions. l Do not try to forcibly open a window, scrape an outside rear view mirror surface or move a wiper or outside rear view mir- ror that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing.

l To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

l Remove any ice that has accumulated on the vehicle chassis. l Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

190

2-5. Driving information

n When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

n When parking the vehicle

Park the vehicle and move the shift lever to P (automatic trans- mission) or to 1 or R (manual transmission) without setting the parking brake. The parking brake may freeze up, preventing it from being released. If necessary, block the wheels to prevent inadvertent sliding or creeping.

Regulations on the use of snow chains

l Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains. Install the chains on the rear tires.

l Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

n Snow chain installation

Observe the following precautions when installing and removing chains.

Install and remove tire chains in a safe location. Install tire chains on the rear tires only. Do not install tire chains on the front tires. Install tire chains following the instructions provided in the accompanying instructions.

191

2-5. Driving information

CAUTION

n Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. l Use tires of the size specified for your vehicle. l Maintain the recommended level of air pressure. l Do not drive in excess of 75 mph (120 km/h) regardless of the type of

snow tires being used.

l Snow tires should be installed on all wheels. l 4WD models:

Do not mix tires of different makes, models, tread patterns or treadwear.

n Driving with snow chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. l Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

l Avoid driving on bumpy road surfaces or over potholes. l Avoid sudden turns and braking. l Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

NOTICE

n Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

n Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

192

2

2-5. Driving information Trailer towing

Your vehicle is designed primarily as a passenger-carrying vehicle, thus towing a trailer will have an adverse effect on handling, perfor- mance, braking, durability, and fuel consumption. For your safety and the safety of others, do not overload the vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. n Weight limits

Confirm the total trailer weight, gross vehicle weight, gross axle weight and trailer tongue load are all within the limits.

n Gross vehicle weight

The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum of the weights of the unloaded vehicle, driver, passengers, luggage, hitch, and the trailer tongue load. It also includes the weight of any special equipment installed on your vehicle.

n Gross axle weight

The load on either the front or rear axle resulting from distribu- tion of the gross vehicle weight on both axles must not exceed the Gross Axle Weight Rating (GAWR) listed on the Certification Label.

Certification label

193

2-5. Driving information

n Trailer tongue load

The trailer cargo load should be distributed so that the tongue load is 9 to 11% of the total trailer weight, not exceeding the maximum 500 lb. (227 kg) (Tongue load / Total trailer weight x 100 = 9 to 11%) The total trailer weight and tongue load can be measured with platform scales found at a highway weighing station, building supply company, trucking company, junk yard, etc.

Total trailer weight Tongue load

Towing a trailer

Consult your Toyota dealer for further information about additional requirements such as a towing kits, etc.

Hitch and tow hitch receiver

n Hitch

Trailer hitch assemblies have different weight capacities estab- lished by the hitch manufacturer. Even though the vehicle may be rated for towing a higher weight, the operator must never exceed the maximum weight rating specified for the trailer hitch.

194

2

2-5. Driving information

Selecting trailer ball

Use the correct trailer ball for your application.

Connecting trailer lights

Trailer ball load rating Matches or exceeds the gross trailer weight rating of the trailer. Ball diameter Matches the size of the trailer coupler. Most couplers are stamped with the required trailer ball size. Shank length Protrudes beyond the bottom of the lock washer and nut at least 2
threads. Shank diameter Matches diameter size.

the ball mount hole

Use the wire harness stored in the rear end underbody.

195

2-5. Driving information

n Before towing

Check that the following conditions are met: l Ensure that your vehicle’s tires are properly inflated. (→P. 477) l Trailer tires should be inflated according to the trailer manufacturer’s rec-

ommendation.

l All trailer lights work to be legal. l Confirm all lights work each time you connect them. l The trailer ball is set up at the proper height for the coupler on the trailer. l Check that your vehicle remains level when a loaded or unloaded trailer is hitched. Do not drive if the vehicle is not level, and check for improper tongue load, overloading, worn suspension, or other possible causes.

l Make sure the trailer cargo is securely loaded. l Check that your rear view mirrors conform to any federal, state/provincial or local regulations. If they do not, install rear view mirrors appropriate for towing purposes. n Break-in schedule

Toyota recommends that you do not use a new vehicle or a vehicle with any new power train components (engine, transmission, differential, wheel bear- ings, etc.) to tow a trailer for the first 500 miles (800 km) of driving.

n Maintenance

If you tow a trailer, your vehicle will require more frequent maintenance due to the additional load. (See “Scheduled Maintenance Guide” or “Owner’s Manual Supplement”.)

l Retighten the fixing bolts of the towing ball and bracket after approxi-

mately 600 miles (1000 km).

196

2

2-5. Driving information

CAUTION

n To avoid accident or injury

l The total trailer weight (trailer weight plus the weight of cargo) must not

exceed 5000 lb. (2270 kg) If a trailer and cargo weight over 2000 lb. (907 kg), use a sway control device with sufficient capacity.

l The gross combined weight (sum of your vehicle weight plus its load and

the total trailer weight) must not exceed the following. 2WD models:

9200 lb. (4173 kg)

4WD models:

9500 lb. (4309 kg)

l Do not exceed the trailer hitch assembly weight, gross vehicle weight,

gross axle weight and trailer tongue load capacities.

l Never load more weight in the back than in the front of the trailer. About 60% of the load should be in the front half of the trailer, and the remaining 40% in the rear.

l The tow hitch receiver installed on your vehicle must never be used on

another vehicle.

n Hitches

If you wish to install a trailer hitch, your Toyota dealer should be consulted.

l Use only a hitch that conforms to the total trailer weight requirement. l Follow the directions supplied by the hitch manufacturer. l Lubricate the hitch ball with a light coat of grease. l Remove the trailer hitch whenever you are not towing a trailer to reduce the possibility of additional damage caused by the hitch if your vehicle is struck from behind.

197

2-5. Driving information

CAUTION

n When towing a trailer

If the total trailer weight exceeds 1000 lb. (453 kg), trailer brakes are required.

l Never tap into your vehicle’s hydraulic system, as this will lower the vehi-

cle’s braking effectiveness.

l Never tow a trailer without using a safety chain securely attached to both the trailer and the vehicle. If damage occurs to the coupling unit or hitch ball, there is danger of the trailer wandering into another lane.

NOTICE

n When installing a trailer hitch

Use only the position recommended by your Toyota dealer. Do not install the trailer hitch on the bumper; this may cause body damage.

n Brakes

Toyota recommends trailers with brakes that conform to any applicable fed- eral and state/provincial regulations.

n Safety chain

A safety chain must always be used between the towing vehicle and the trailer. Leave sufficient slack in the chain for turns. The chain should cross under the trailer tongue to prevent the tongue from dropping to the ground in the case that it becomes damaged or separated. For the correct safety chain installation procedure, ask your Toyota dealer.

n Do not directly splice trailer lights

Directly splicing trailer lights may damage your vehicle’s electrical system and cause a malfunction.

198

2

2-5. Driving information

Trailer towing tips

Your vehicle will handle differently when towing a trailer. In order to