2010 Toyota Camry Owners Manual

2-1. Driving procedures

Starting on a steep uphill

Automatic transmission

STEP 1

STEP 2

STEP 3

Firmly set the parking brake and shift the shift lever to D. Gently depress the accelerator pedal. Release the parking brake.

Manual transmission

STEP 1

STEP 2

STEP 3

With the parking brake firmly set and the clutch pedal fully depressed, shift the shift lever to 1. Lightly depress the accelerator pedal at the same time as gradually releasing the clutch pedal. Release the parking brake.

■Driving in the rain

●Drive carefully when it is raining, because visibility will be reduced, the

windows may become fogged-up, and the road will be slippery.

●Drive carefully when it starts to rain, because the road surface will be

especially slippery.

●Refrain from high speeds when driving on an expressway in the rain, because there may be a layer of water between the tires and the road surface, preventing the steering and brakes from operating properly.

■Breaking in your new Toyota

To extend the life of the vehicle, the following precautions are recommended to observe: ●For the first 186 miles (300 km):

Avoid sudden stops.

●For the first 994 miles (1600 km):

• Do not drive at extremely high speeds. • Avoid sudden acceleration. • Do not drive continuously in the low gears. • Do not drive at a constant speed for extended periods.

122

2-1. Driving procedures

■Drum-in-disc type parking brake system

Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or when- ever the parking brake shoes and/or drum are replaced. Have your Toyota dealer perform the bedding down.

■Operating your vehicle in a foreign country

Comply with the relevant vehicle registration laws and confirm the availability of the correct fuel. (→P. 484)

CAUTION

■When starting the vehicle (vehicles with an automatic transmission)

Always keep your foot on the brake pedal while stopped with the engine run- ning. This prevents the vehicle from creeping.

■When driving the vehicle

●Do not drive if you are unfamiliar with the location of the brake and accel-

erator pedals to avoid depressing the wrong pedal. • Accidentally depressing the accelerator pedal instead of the brake pedal will result in sudden acceleration that may lead to an accident that could result in death or serious injury.

• When backing up, you may twist your body around, leading to a diffi- culty in operating the pedals. Make sure to operate the pedals properly. • Make sure to keep a correct driving posture even when moving the vehicle only slightly, allowing you to depress the brake and accelerator pedals properly.

• Depress the brake pedal using your right foot. Depressing the brake pedal using your left foot may delay response in an emergency, result- ing in an accident.

●Do not drive the vehicle over or stop the vehicle near flammable materials. The exhaust system and exhaust gases can be extremely hot. This may cause a fire if there is any flammable material nearby.

●Vehicles with an automatic transmission: Do not let the vehicle roll back- wards while the shift lever is in a driving position, or roll forward while the shift lever is in R. Doing so may cause the engine to stall or lead to poor brake and steering performance, resulting in an accident or damage to the vehicle.

123

2-1. Driving procedures

CAUTION

●If the smell of exhaust is noticed inside the vehicle, open the windows and check that the trunk is closed. Large amounts of exhaust in the vehicle can cause driver drowsiness and an accident, resulting in death or a serious health hazard. Have the vehicle inspected by your Toyota dealer immedi- ately.

●On vehicles with an automatic transmission, do not shift the shift lever to P

while the vehicle is moving. Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to R while the vehicle is moving forward.

Doing so can damage the transmission and may result in a loss of vehicle control.

●Do not shift the shift lever to D (vehicles with an automatic transmission) or 1 (vehicles with a manual transmission) while the vehicle is moving back- ward. Doing so can damage the transmission and may result in a loss of vehicle control.

●Moving the shift lever to N while the vehicle is moving will disengage the engine from the transmission. Engine braking is not available when N is selected.

●During normal driving, do not turn off the engine. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so. However, in the event of an emergency, such as if it becomes impossible to stop the vehicle in the normal way: →P. 432

●Use engine braking (downshift) to maintain a safe speed when driving

down a steep hill. Using the brakes continuously may cause the brakes to overheat and lose effectiveness. (→P. 139)

124

2

2-1. Driving procedures

CAUTION

●When stopped on an inclined surface, use the brake pedal and parking brake to prevent the vehicle from rolling backward or forward and causing an accident.

●Do not adjust the position of the steering wheel, the seat, or the inside or

outside rear view mirrors while driving. Doing so may result in a loss of vehicle control that can cause accidents that may result in death or serious injury.

●Always check that all passengers' arms, heads or other parts of their bod- ies are not outside the vehicle, as this may result in death or serious injury. ●Do not drive in excess of the speed limit. Even if the legal speed limit per- mits it, do not drive over 85 mph (140 km/h) unless your vehicle has high- speed capability tires. Driving over 85 mph (140 km/h) may result in tire failure, loss of control and possible injury. Be sure to consult a tire dealer to determine whether the tires on your vehicle are high-speed capability tires or not before driving at such speeds. ■When driving on slippery road surfaces

●Sudden braking, acceleration and steering may cause tire slippage and

reduce your ability to control the vehicle, resulting in an accident.

●Sudden changes in engine speed, such as engine braking caused by up- shifting or down-shifting, may cause the vehicle to skid, resulting in an accident.

●After driving through a puddle, lightly depress the brake pedal to make sure that the brakes are functioning properly. Wet brake pads may prevent the brakes from functioning properly. If the brakes on only one side are wet and not functioning properly, steering control may be affected, resulting in an accident.

■When shifting the shift lever

Vehicles with an automatic transmission: Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

125

2-1. Driving procedures

CAUTION

■When the vehicle is stopped

●Do not race the engine.

If the vehicle is in any gear other than P (automatic transmission only) or N the vehicle may accelerate suddenly and unexpectedly, and may cause an accident.

●Do not leave the vehicle with the engine running for a long time.

If such a situation cannot be avoided, park the vehicle in an open space and check that exhaust fumes do not enter the vehicle interior.

●Vehicles with an automatic transmission: Always keep a foot on the brake pedal while the engine is running to prevent an accident caused by the vehicle moving.

■When the vehicle is parked

●Do not leave glasses, cigarette lighters, spray cans, or soft drink cans in

the vehicle when it is in the sun. Doing so may result in the following. • Gas may leak from a cigarette lighter or spray can, and may lead to a

fire.

• The temperature inside the vehicle may cause the plastic lenses and

plastic material of eye glasses to deform or crack.

• Soft drink cans may fracture, causing the contents to spray over the interior of the vehicle, and may also cause a short circuit in the vehi- cle's electrical components.

●Always apply the parking brake, shift the shift lever to P (automatic trans-

mission only), stop the engine and lock the vehicle. Do not leave the vehicle unattended while the engine is running.

●Do not touch the exhaust pipe while the engine is running or immediately

after turning the engine off. Doing so may cause burns.

●Do not leave the engine running in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the engine is running, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

126

2-1. Driving procedures

CAUTION

■Exhaust gases

Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard. ●If the vehicle is in a poorly ventilated area, stop the engine. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

●The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard. ■When taking a nap in the vehicle

Always turn the engine off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to engine overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

127

2-1. Driving procedures

CAUTION

■When braking the vehicle

●When the brakes are wet, drive more cautiously.

Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle.

●If the power brake assist function does not operate, do not follow other

vehicles closely and avoid downhills or sharp turns that require braking. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.

●Do not pump the brake pedal if the engine stalls.

Each push on the brake pedal uses up the reserve for the power-assisted brakes.

●The brake system consists of 2 individual hydraulic systems: If one of the systems fails, the other will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

128

2-1. Driving procedures

NOTICE

■When driving the vehicle

Manual transmission

●Do not shift gears unless the clutch pedal is fully depressed. After shifting, do not release the clutch abruptly. Doing so may damage the clutch, trans- mission and gears.

●Do not rest your foot on the clutch pedal while driving.

Doing so may cause clutch trouble.

●Do not use any gears other than the first gear when starting off and mov-

ing forward. Doing so may damage the clutch.

●Do not use the clutch to hold the vehicle when stopping on an uphill grade.

Doing so may damage the clutch.

●Do not shift into reverse when the vehicle is still moving. Doing so may

damage the clutch, transmission and gears. Automatic transmission

Do not use the accelerator pedal or depress the accelerator and brake ped- als together to hold the vehicle on a hill.

■When parking the vehicle

Vehicles with an automatic transmission: Always put the shift lever in P. Fail- ure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is accidentally depressed.

■Avoiding damage to vehicle parts

●Do not turn the steering wheel fully in either direction and hold it there for a

long time. Doing so may damage the power steering motor.

●When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

129

2-1. Driving procedures

NOTICE

■If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or that of the brake discs are exceeded.

■If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. ●It may be difficult to control your vehicle. ●The vehicle will make abnormal sounds. ●The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 457)

■When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. ●Engine stalling ●Short in electrical components ●Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. ●Brake function ●Changes in quantity and quality of engine oil, and transaxle fluid etc. ●Lubricant condition for the bearings and suspension joints (where possi-

ble) and the function of all joints, bearings, etc.

130

2-1. Driving procedures Engine (ignition) switch (vehicles with smart key system)

Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine STEP 1

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. The “ENGINE START STOP” switch indicator turns green. If the indicator does not turn green, the engine cannot be started.

STEP 2

STEP 3

STEP 4

Press the “ENGINE START STOP” switch.

The engine will crank until it starts or for up to 25 seconds, whichever is less. If you press and hold the “ENGINE START STOP” switch, the engine will keep cranking for about 30
seconds maximum. Continue depressing the brake pedal until the engine is com- pletely started. The engine can be started from any mode.

131

2-1. Driving procedures

■ Changing “ENGINE START STOP” switch mode Modes can be changed by pressing the “ENGINE START STOP” switch with the brake pedal released. (The mode changes each time the switch is pressed.)

OFF* Emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “ENGINE START STOP” switch indicator turns amber. IGNITION ON mode All electrical components can be used. The “ENGINE START STOP” switch indicator turns amber.

*: If the shift lever is in a position other than “P” when turning off the engine, “ENGINE START STOP” switch will be turned to ACCESSORY mode, not to OFF.

the

132

■Steering lock release

2-1. Driving procedures

Make sure that the steering wheel lock is released. To release the steering wheel lock, gently turn the wheel left or right while pressing the “ENGINE START STOP” switch. If the steering wheel lock does not release, the “ENGINE START STOP” switch indicator will flash green.

■If the engine does not start

The engine immobilizer system may not have been deactivated. (→P. 80) ■When the “ENGINE START STOP” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. ■Auto power OFF function

If the vehicle is left in ACCESSORY mode for more than an hour with the shift lever in P, the “ENGINE START STOP” switch will automatically turn OFF.

■Key battery depletion

→P. 32

■When the electronic key battery is discharged

→P. 401

■Conditions affecting operation

→P. 30

■Note for the entry function

→P. 33

133

2-1. Driving procedures

CAUTION

■When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Stopping the engine in an emergency

If you want to stop the engine in an emergency while driving the vehicle, push and hold the “ENGINE START STOP” switch for more than 3 seconds. However, do not touch the "ENGINE START STOP" switch while driving except in an emergency. Turning the engine off while driving will not cause loss of steering or braking control, but the power assist to these systems will be lost. This will make it more difficult to steer and brake, so you should pull over and stop the vehicle as soon as it is safe to do so.

NOTICE

■To prevent battery discharge

Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNI- TION ON mode for long periods without the engine running.

■When starting the engine ●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

134

2

2-1. Driving procedures Engine (ignition) switch (vehicles without smart key system)

■ Starting the engine

Automatic transmission

STEP 1

STEP 2

STEP 3

STEP 4

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. Turn the engine switch to the “START” position and start the engine.

Manual transmission

STEP 1

STEP 2

STEP 3

STEP 4

Check that the parking brake is set. Check that the shift lever is set in N. Firmly depress the clutch pedal. Turn the engine switch to the “START” position and start the engine.

■ Changing engine switch mode

“LOCK” The steering wheel is locked and the key can be removed. (Vehicles with an automatic transmission: The key can be removed only when the shift lever is in “P”.) “ACC” Some electrical components such as the audio system can be used. “ON” All electrical components can be used. “START” For starting the engine.

135

2-1. Driving procedures

■Turning the key from “ACC” to “LOCK”

■Steering lock release

STEP 1

STEP 2

Shift the shift lever to N (manual transmission) or P (automatic transmission). (→P. 138, 142) Push in the key and turn to the “LOCK” position.

When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turn- ing the steering wheel slightly in either direction.

■If the engine does not start

The engine immobilizer system may not have been deactivated. (→P. 80)

■Key reminder buzzer

A buzzer sounds if the driver’s door is opened while the key is in the “LOCK” position to remind you to remove the key.

CAUTION

■When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution when driving

Do not turn the engine switch to the “LOCK” position while driving. If, in an emergency, you must turn the engine off while the vehicle is moving, turn the key only to the “ACC” position.

136

2

2-1. Driving procedures

NOTICE

■To prevent battery discharge

Do not leave the key in the “ACC” or “ON” position for long periods if the engine is not running.

■When starting the engine

●Do not crank for more than 30 seconds at a time. This may overheat the

starter and wiring systems. ●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

137

2-1. Driving procedures Automatic transmission∗

Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever

Vehicles with smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, depress the brake pedal and move the shift lever. Vehicles without smart key system: While the engine switch is in the “ON” position, depress the brake pedal and move the shift lever.

138

∗: If equipped

2-1. Driving procedures

■ Shift position uses

Shift position

Function

Parking the vehicle or starting the engine

Reversing Neutral

Normal driving*1
S mode driving*2

(→P. 139)

*1: Shifting to the D position allows the system to select a gear suitable

for the driving conditions. Setting the shift lever to the D position is recommended for normal driving.

*2: Selecting shift ranges using S mode restricts the upper limit of the possible gear ranges, controls engine braking force, and prevents unnecessary upshifting.

Changing shift ranges in S mode

When the shift lever is in the S position, the shift lever can be oper- ated as follows:

Upshifting Downshifting

The initial shift range in S mode is set automatically to 5 or 4 accord- ing to vehicle speed. However, the initial shift range may be set to 3 if AI-SHIFT has operated while the shift lever was in the D position. (→P. 141)

139

2-1. Driving procedures

■ Shift ranges and their functions

Shift range

Function

A gear between 1 and 6 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 5 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 4 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 3 is automatically selected according to vehicle speed and driving conditions. A gear between 1 and 2 is automatically selected according to vehicle speed and driving conditions. Setting the gear at 1.

A lower shift range will provide greater engine braking force than a higher shift range.

■Downshifting restrictions

To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (The warning buzzer will sound twice.)

■When driving with the cruise control system

Engine braking will not occur during shift range selection in the D position or S mode, even when downshifting to range 5 or 4. (→P. 166)

■If the shift lever cannot be shifted from P

→P. 467

140

2

2-1. Driving procedures

■If the “S” indicator does not come on even after shifting the shift lever

to S This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the vehicle will operate as if the shift lever is in D.)

■S mode

●When the shift range is 5 or lower, holding the shift lever toward “+” sets

the shift range to 6.

●To prevent the engine from over-revving, upshifting may automatically

occur.

●To protect the automatic transmission, a function is adopted that auto-

matically shifts to the top range when the temperature is too hot.

■AI-SHIFT

The AI-SHIFT automatically shifts the gear to the suitable position according to the driver performance and driving conditions. The AI-SHIFT automatically operates when the shift lever is in the D posi- tion. (Shifting the shift lever to the S position cancels the function.)

141

2-1. Driving procedures Manual transmission∗

■ Shifting the shift lever

Fully depress the clutch pedal before operating the shift lever, and then release it slowly. ■ Shifting the shift lever to R

Shift the shift lever to the R position while lifting up the ring section.

142

∗: If equipped

2

2-1. Driving procedures

■Maximum allowable speeds

Observe the following maximum allowable speeds in each gear when maxi- mum acceleration is necessary.

mph (km/h)

Shift position

Maximum speed

32 (52) 56 (91) 83 (135) 118 (191) 130 (210)

NOTICE

■To prevent damage to the transmission

●Do not shift the shift lever to R without

depressing the clutch pedal.

●Do not lift up the ring section except when shifting the lever to R. ●Shift the shift lever to R only when the vehicle is stationary.

143

2-1. Driving procedures Turn signal lever

Right turn Left turn Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever.

■Turn signals can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position. ■If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

144

2-1. Driving procedures Parking brake

Manual transmission

U.S.A. Canada

Sets the parking brake Fully apply the parking brake while depressing the brake pedal. Releases the parking brake Slightly raise the lever and lower it completely while pressing the but- ton. Automatic transmission

Sets the parking brake* (Depressing the pedal again releases the parking brake.)

*: Fully depress

the parking brake pedal with your left foot while depressing the brake pedal with your right foot.

U.S.A. Canada

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

145

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 65)

146

2-2. Instrument cluster Gauges and meters

Vehicles with multi-information display

Vehicles with smart key system: The following gauges, meters and displays illuminate when the “ENGINE START STOP” switch is in IGNITION ON mode. Vehicles without smart key system: The following gauges, meters and displays illuminate when the engine switch is in the “ON” posi- tion.

Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Multi-information display →P. 155
Fuel gauge Displays the quantity of fuel remaining in the tank.

147

2-2. Instrument cluster

Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays. Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button. (→P. 150) Automatic transmission shift position indicator lights →P. 138
Automatic transmission shift range display →P. 138

148

Vehicles without multi-information display

2-2. Instrument cluster

The following gauges, meters and displays illuminate when the engine switch is in the “ON” position. Engine coolant temperature gauge Displays the engine coolant temperature. Tachometer Displays the engine speed in revolutions per minute. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter displays. Pressing and holding the button will reset the trip meter when the trip meter is being displayed. To adjust the brightness of the instrument panel light, turn the button. (→P. 150)

149

2-2. Instrument cluster

Odometer, trip meter and outside temperature display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently. Outside temperature: Displays the outside temperature. Automatic transmission shift position indicator lights →P. 138
Automatic transmission shift range display →P. 138

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Darker Brighter When the headlight switch is turned to on, the brightness will be reduced slightly unless the control dial is turned fully clockwise.

NOTICE

■To prevent damage to the engine and its components

●Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

●The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 475)

150

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster (vehicles with multi-information display)

Instrument cluster (vehicles without multi-information display)

151

2-2. Instrument cluster

Center panel

152

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

(U.S.A.)

(CANADA)

(if equipped)

Turn signal indicator (→P. 144)

Headlight high beam indicator (→P. 160)

Slip indicator (→P. 170)

VSC OFF indicator (→P. 171)

“TRAC OFF” indicator (→P. 171)

Engine immobilizer/ alarm system indicator (→P. 80, 82)

Headlight indicator (→P. 159)

Tail light indicator (→P. 159)

Front fog light indicator (→P. 163)

SRS airbag on-off indi- cator (→P. 99)

Cruise control indicator (→P. 166)

Cruise control set indi- cator (→P. 166)

153

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 432)

(CANADA)

(U.S.A.)

(CANADA)

(U.S.A.)

(CANADA)

(if equipped)

(U.S.A.)

(U.S.A.)

(U.S.A.)

(if equipped) (if equipped)

(if equipped)

*: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with smart key system) or the engine switch is turned to the “ON” position (vehicles without smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS or the SRS airbag warning light not come on when you start the engine, this could mean that these sys- tems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

154

2-2. Instrument cluster Multi-information display∗

The multi-information display presents the driver with a variety of driving-related data, including the outside temperature.

● Outside

temperature dis- (→P. 156) play Indicates the outside tempera- ture.

● Trip information

(→P. 156) Displays driving range, fuel consumption and other cruis- ing-related information.

● Warning messages

(→P. 444) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.

● Odometer and trip meter

display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the dis- tance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances indepen- dently.

∗: If equipped 155

2-2. Instrument cluster

Switch the display

Display items can be switched by pressing the “DISP” button.

The display will return to the out- side temperature display when the “DISP” button is pressed and held.

● Outside temperature

● Cruising range

Displays the outside air temperature.

The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining. • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated.

● Average fuel consumption after refueling

Displays the average fuel consumption since the vehicles was last refueled.

156

2-2. Instrument cluster

● Driving distance

Displays the driving distance since the engine was started.

● Average vehicle speed

Displays the average vehicle speed since the engine was started.

● Cruise information off

Displays the odometer and trip meters only.

● Zoom display of odometer and trip meter

Displays the odometer and one of the trip meters simultaneously.

■Outside temperature display

In the following situations, the correct outside temperature may not be dis- played, or the display may take longer than normal to change. ●When stopped, or driving at low speeds (less than 12 mph [20 km/h]) ●When the outside temperature has changed suddenly (at the entrance/

exit of a garage, tunnel, etc.)

157

2-2. Instrument cluster

NOTICE

■The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

158

2

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically.

For U.S.A.

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “ENGINE START STOP” switch or the engine switch is in ON) Daytime running light system is off.

159

2-3. Operating the lights and wipers

For Canada

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “ENGINE START STOP” switch or the engine switch is in ON)

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

160

2

2-3. Operating the lights and wipers

■The headlights can be operated automatically when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

■Daytime running light system

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the engine is started and the parking brake is released. Daytime running lights are not designed for use at night. For U.S.A.: Daytime running lights can be turned off by operating the switch.

■Headlight control sensor

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. Doing so the sensor detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

161

2-3. Operating the lights and wipers

■Automatic light off system

Vehicles with smart key system

●When the headlights are on: The headlights and tail lights turn off 30 sec- onds after all doors are closed with the “ENGINE START STOP” switch OFF. (The lights turn off immediately if on the key is pressed after all doors are locked.)

●When only the tail lights are on: The tail lights turn off automatically if the “ENGINE START STOP” switch is turned OFF and the driver’s door is opened.

To turn the lights on again, turn the “ENGINE START STOP” switch to IGNI- or TION ON mode, or turn the headlight switch off and then back to

position.

If any of the doors or trunk lid is kept open, the lights automatically turn off after 20 minutes.

Vehicles without smart key system

●When the headlights are on: The headlights and tail lights turn off 30 sec- onds after all doors are closed with the engine switch OFF. (Vehicles with wireless remote control: The lights turn off immediately if on the key is pressed after all doors are locked.)

●When only the tail lights are on: The tail lights turn off automatically if the

engine switch is turned OFF and the driver’s door is opened.

To turn the lights on again, turn the engine switch to the “ON” position, or turn the headlight switch off and then back to If any of the doors or trunk lid is kept open, the lights automatically turn off after 20 minutes.

position.

or

■Customization that can be configured at Toyota dealer

Settings (e.g. Light sensor sensitivity) can be changed. (Customizable features →P. 510)

NOTICE

■To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

162

2-3. Operating the lights and wipers Fog light switch∗

The fog lights improve visibility in difficult driving conditions, such as in rain or fog. They can be turned on only when the headlights are on low beam.

Off Front fog lights on

∗: If equipped 163

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation.

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

the

Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency

164

2-3. Operating the lights and wipers

Wash/wipe operation

Wipers operate automatically.

■The windshield wiper and washers can be operated when

Vehicles with smart key system

The “ENGINE START STOP” switch is in IGNITION ON mode.

Vehicles without smart key system

The engine switch is in the “ON” position.

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

165

2-4. Using other driving systems Cruise control

Use the cruise control to maintain a set speed without using the accelerator.

Indicators Cruise control switch

Turn the “ON-OFF” button on. At this time, the cruise control indicator will come on. Press the button once more to deactivate the cruise control.

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

At this time, the cruise control set indicator will come on.

■ Setting the vehicle speed STEP 1

STEP 2

166

2

■ Adjusting the speed setting

2-4. Using other driving systems

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed (approximately 1.0 mph [1.6 km/h]) can be made by lightly pushing the lever up or down and releasing it.

■ Canceling and resuming regular acceleration

Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied or the clutch pedal (manual is depressed. Resume To resume cruise control and return to the set speed, push the lever up.

transmission)

167

2-4. Using other driving systems

■Cruise control can be set when

●Automatic transmission:

The shift lever is in D, 4, 5 or 6 range of S. ●Vehicle speed is above 25 mph (40 km/h).

■Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

■Automatic cruise control cancellation

The set speed is automatically canceled in any of the following situations. ●Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Contact your Toyota dealer and have your Toyota inspected.

168

2

2-4. Using other driving systems

CAUTION

■To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

169

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. ■ ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface.

■ Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

■ VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

■ TRAC (Traction Control)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

When VSC and TRAC are operating

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that VSC/TRAC have been engaged. A buzzer (intermittent) sounds to indicate that VSC is operating.

170

2-4. Using other driving systems

To disable TRAC and/or VSC

If the vehicle gets stuck in fresh snow or mud, TRAC and VSC may reduce power from the engine to the wheels. You may need to turn the system off to enable you to rock the vehicle in order to free it. ■ Turning off TRAC

Quickly push and release the button to turn off TRAC.

■ Turning off TRAC and VSC

The “TRAC OFF” indicator light should come on. Push the button again to turn the system back on.

Push and hold the button for more than 3 seconds while the vehicle is stopped to turn off TRAC and VSC.

The “TRAC OFF” and VSC OFF indicator lights should come on. Push the button again to turn the system back on.

171

2-4. Using other driving systems

■Automatic reactivation of TRAC and VSC

Vehicles with smart key system

Turning the “ENGINE START STOP” switch OFF after turning off the TRAC and VSC systems will automatically re-enable them.

Vehicles without smart key system

Turning the engine switch OFF after turning off the TRAC and VSC systems will automatically re-enable them.

■Automatic TRAC reactivation

If only the TRAC system is turned off, the TRAC system will turn on when vehicle speed increases.

■Automatic TRAC and VSC reactivation

If the TRAC and VSC systems are turned off, the systems will not turn on even when vehicle speed increases.

■Sounds and vibrations caused by ABS, brake assist, VSC and TRAC ●A sound may be heard from the engine compartment when the engine is started or just after the vehicle begins to move. This sound does not indi- cate that a malfunction has occurred in any of these systems.

●Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop. • The brake pedal may pulsate slightly after ABS is activated. • The brake pedal may move down slightly after ABS is activated.

■If the slip indicator comes on...

It may indicate a malfunction in the VSC and TRAC. Contact your Toyota dealer.

172

2

2-4. Using other driving systems

CAUTION

■ABS does not operate effectively when

●Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

●The vehicle hydroplanes while driving at high speed on the wet or slick

road.

■Stopping distance when ABS is operating on the wet or slick roads

ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. ●When driving on dirt, gravel or snow-covered roads ●When driving with tire chains ●When driving over bumps in the road ●When driving over roads with potholes or uneven roads

■TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

173

2-4. Using other driving systems

CAUTION

■When VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

■When TRAC and VSC are off

Be especially careful and drive at a speed appropriate to the road condi- tions. As these are systems to ensure vehicle stability and driving force, do not turn off TRAC and VSC unless necessary.

■Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC system will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

■Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

174

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. ● Stow cargo and luggage in the trunk whenever possible. ● Be sure all items are secured in place. ● Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

● For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit ⎯ (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb. passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 - 750
(150 × 5) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

175

2-5. Driving information

(6)

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (→P. 183)

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 900 lb. (410
kg), the available amount of cargo and luggage load capacity will be as follows: 900 lb. - 366 lb. = 534 lb. (410 kg -166 kg = 244 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

534 lb. - 388 lb. = 146 lb. (244 kg - 176 kg = 68 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

176

2

2-5. Driving information

CAUTION

■Storage precautions

Observe the following precautions. Failing to do so may result in death or serious injury. ●Vehicles with fold-down type rear seat: To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep cargo and luggage low, as close to the floor as possible.

●Vehicles with fold-down type rear seat: Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. They should ride in their seats with their seat belts properly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking, sudden swerving or a collision.

●Do not place cargo or luggage in or on the following locations as the item may get under the clutch, brake or accelerator pedal and prevent the pedals from being depressed properly, block the driver’s vision, or hit the driver or passengers, causing an accident. • Driver’s feet • Front passenger or rear seats (when stacking items) • Package tray • Instrument panel • Dashboard

●Secure all items in the occupant compartment, as they may shift and injure someone during sudden braking, sudden swerving or an acci- dent.

■Capacity and distribution

●Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

●Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.