2004 Toyota Camry Owners Manual

memory (all three programs)

To erase all previously programmed codes at one time, press and hold down the 2
outside buttons for 20 seconds until the indicator light flashes. If you sell your vehicle, be sure to erase the programs stored the HomeLinkR memory.

in

’04Camry_U (L/O 0307)

that may be received,

This device complies with FCC Rules Part 15. Operation is subject to the fol- lowing two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interfer- ence including interference that may cause undesired operation. WARNING: This transmitter has been tested and complies with FCC and DOC/MPAC rules. Changes or modifi- cations not expressly approved by the party compliance could void the user’s authority to op- erate the device.

responsible

for

CAUTION

D When programming the HomeLinkR Universal Transceiver, you may be operating a garage door or other device. Make sure people and ob- jects are out of the way of the ga- rage door or other device to pre- vent potential harm or damage.

D Do not use this HomeLinkR Univer- sal Transceiver with any garage door opener that lacks the safety stop and reverse feature as re- quired by federal safety standards. (This includes any garage door opener model manufactured before April 1, 1982.) A garage door open- er which cannot detect an object (signaling the door to stop and re- verse), does not meet current feder- al safety standards. Using a garage door opener without these features increases risk of serious injury or death.

189

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Glove box

Auxiliary boxes

To use the glove box, do this. To open: Pull the lever. With the instrument panel lights on, the glove box light will come on when the glove box is open. To lock: Insert the master key and turn it clockwise.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the glove box door closed while driving.

injury

190

Instrument panel

Over head console

To use above.

the box, open

it as shown

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the auxiliary box closed while driving.

injury

NOTICE

Over head console box—During hot weather, the interior of the vehicle becomes very hot. Do not leave any- thing flammable or deformable such as a lighter, glasses, etc. inside.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Rear console box

UPPER TRAY To access the upper tray, raise the con- sole box lid while pushing the lock re- lease button.

CONSOLE BOX To access the rear console box, pull up the lock release lever while raising the rear console box lid.

CAUTION

To reduce the chance of in case of an accident or a sudden stop, always keep the console box closed while driving.

injury

191

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Front cup holder

Rear cup holder

The cup holder is designed for holding cups or drink−cans securely. With lever type parking brake: To use the cup holder, open the lid. With pedal type parking brake: To use the cup holder, push the lid. To hold the cups or drink−cans securely, adjust the size with the adapter.

CAUTION

D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

D To reduce the chance of injury in case of an accident or sudden stop while driving, keep the cup holder closed when it is not in use.

With lever type parking brake

With pedal type parking brake

192

The cup holder is designed for holding cups or drink−cans securely. To use the cup holder, pull down the arm- rest.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Storage box

Grocery bag hooks

CAUTION

D Do not place anything else other than cups or drink−cans in the cup items may be holder, as such thrown about in the compartment and possibly injure people in the vehicle during sudden braking or in an accident.

D Do not lift the armrest upright when

the cup holder is in use.

This box is designed to hold things like bottles.

This hook is designed to hang things like grocery bags.

NOTICE

To prevent damage to the hook, avoid hanging heavy loads on it.

193

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Cargo net

Rear sun shade

Floor mat

To secure belongings, hang the cargo net on the hooks.

NOTICE

z Do not use the net to secure sharp or heavy object. The net will tear off.

z Be sure not to twist the net when

hooking.

194

To raise the rear sun shade, pull the tab of the shade and hook it on the anchors. To lower the shade, pull the tab slightly to unhook the shade, and lower it slowly.

Use a floor mat of the correct size. If the floor carpet and floor mat have 2
holes, then they are designed for use with locking clips. Fix the floor mat with lock- ing clips into the holes in the floor carpet.

NOTICE

Observe the following, otherwise dam- age and/or failure may result: z Do not place anything where they may hinder the opening/closing of the shade.

z Do not place things on the shade.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

CAUTION

Make sure the floor mat is properly placed on the floor carpet. If the floor mat slips and the movement of the pedals during driv- ing, it may cause an accident.

interferes with

195

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

196

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

SECTION 2

INFORMATION BEFORE DRIVING YOUR TOYOTA Information before driving your Toyota Break−in period Fuel Fuel pump shut off system Operation in foreign countries Three−way catalytic converters Engine exhaust cautions Facts about engine oil consumption Iridium−tipped spark plugs Brake system Brake pad wear limit indicators Your Toyota’s identification Theft prevention labels Suspension and chassis Tire information Vehicle load limits Cargo and luggage Types of tires

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

198
198
200
200
201
202
203
204
204
208
208
210
210
211
219
219
222

197

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Break−in period Drive gently and avoid high speeds. Your vehicle does not need an elaborate break−in. But following a few simple tips for the first 1600 km (1000 miles) can add to the future economy and long life of your vehicle: D Avoid full

throttle acceleration when

starting and driving.

D Avoid racing the engine. D Try to avoid hard stops during the first

300 km (200 miles).

D Do not drive slowly with the manual

transmission in a high gear.

D Do not drive for a long time at any

single speed, either fast or slow.

D Do not tow a trailer during the first 800

km (500 miles).

Fuel FUEL TYPE Your new vehicle must use only un- leaded gasoline. To help prevent gas station mix−ups, your Toyota has a smaller fuel tank opening. The special nozzle on pumps with un- leaded fuel will fit it, but the larger stan- dard nozzle on pumps with leaded gas will not. At a minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB 3.5−M93
in Canada.

NOTICE

Do not use leaded gasoline. Use of leaded gasoline will cause the three− way catalytic converter to lose its ef- fectiveness and the emission control system to function improperly. Also, this can increase maintenance costs.

OCTANE RATING 2AZ−FE engine: Select Octane Rating 87
(Research Octane Number 91) or higher. 1MZ−FE and 3MZ−FE engines: Select Octane Rating 87 (Research Octane Number 91) or higher. For improved ve- hicle performance, the use of premium unleaded gasoline with an Octane Rat- ing of 91 (Research Octane Number of 96) or higher is recommended. Use of unleaded gasoline with an octane rating or research octane number lower than stated above will cause persistent heavy knocking. If it is severe, this will lead to engine damage. If your engine knocks... If you detect heavy knocking even when using if you hear steady knocking while holding a steady speed on level roads, consult your Toyota dealer. However, occasionally, you may notice light knocking for a short time while accel- erating or driving up hills. This is normal and there is no need for concern.

the recommended

fuel, or

198

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

in

GASOLINE CONTAINING DETERGENT ADDITIVES Toyota recommends the use of gasoline that contains detergent additives to avoid build−up of engine deposits. However, all gasoline sold the U.S. contains detergent additives to keep clean and/or clean intake systems. QUALITY GASOLINE Automotive manufacturers in the U.S., Europe and Japan have developed a specification fuel named World−Wide Fuel Charter (WWFC) that is expected to be applied world wide. The WWFC consists of four categories that depend on required emisvels. In the U.S., category 3 or 4 has beension le adopted. The WWFC improves air quality by providing for better emis- sions in vehicle fleets, and customer satisfaction through better vehicle per- formance.

for quality

’04Camry_U (L/O 0307)

CLEANER BURNING GASOLINE Cleaner burning gasoline, including re- formulated gasoline that contains oxy- genates such as ethanol or MTBE is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gas- oline provide excellent vehicle perfor- mance, reduce vehicle emissions, and im- prove air quality. OXYGENATES IN GASOLINE Toyota allows the use of oxygenate blended gasoline where the oxygenate content is up to 10% ethanol or 15% MTBE. in your Toyota, be sure that it has an octane rating no lower than 87. Toyota does not recommend the use of gasoline containing methanol.

If you use gasohol

GASOLINE CONTAINING MMT Some gasoline contain an octane en- hancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel con- taining MMT is used, your emission con- trol system may be adversely affected. The Malfunction Indicator Lamp on the in- strument cluster may come on. If this hap- pens, contact your Toyota dealer for ser- vice. GASOLINE QUALITY In a very few cases, you may experience driveability problems caused by the partic- ular gasoline that you are using. If you continue to have unacceptable driveability, try changing gasoline brands. If this does not rectify your problem, then consult your Toyota dealer.

199

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Fuel pump shut off system The fuel pump shut off system stops sup- plying fuel to the engine to minimize the risk of fuel leakage when the engine stalls or an airbag inflates upon collision. To restart the engine after the fuel pump shut off system activates, ignition switch to “ACC” or “LOCK” once and start it.

turn

the

CAUTION

Inspect the ground under the vehicle before restarting the engine. If you find that liquid has leaked onto the ground, it indicates the fuel system has been damaged and it is in need of repair. In this case, do not restart the engine.

NOTICE

z Do not use gasohol other

than stated above. It will cause fuel sys- tem damage or vehicle performance problems.

z If driveability problems are encoun- tered (poor hot starting, vaporizing, engine knock, etc.), discontinue the use.

z Take care not to spill gasohol dur- ing refueling. Gasohol may cause paint damage.

FUEL TANK CAPACITY

70 L (18.5 gal., 15.4 lmp. gal.)

200

Operation in foreign countries If you plan to drive your Toyota another country... First, comply with the vehicle registration laws. Second, confirm the availability of the cor- rect fuel (unleaded and minimum octane number).

in

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Three−way catalytic converters

The three−way catalytic converter is an emission control device installed in the exhaust system. The purpose is to reduce pollutants in the exhaust gas.

CAUTION

D Keep people and combustible mate- rials away from the exhaust pipe while the engine is running. The exhaust gas is very hot.

D Do not drive, idle or park your ve- hicle over anything that may burn easily such as grass, leaves, paper or rags. D Do not

that may burn easily, such as paper or rags, in the engine compartment.

leave anything

2AZ−FE engine

1MZ−FE and 3MZ−FE engines

NOTICE

large amount of unburned gases into the three−way catalytic flowing converter may cause it to overheat and create a fire hazard. To prevent this and other damage, observe the following precautions: z Use only unleaded gasoline. z Do not drive with an extremely low fuel level; running out of fuel could cause the engine to misfire, creat- ing an excessive load on the three− way catalytic converter.

z Do not allow the engine to run at idle speed for more than 20 min- utes.

z Avoid racing the engine. z Do not push−start or pull−start your

vehicle.

z Do not turn off the ignition while

the vehicle is moving.

201

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Engine exhaust cautions

CAUTION

D Avoid inhaling the engine exhaust. It contains carbon monoxide, which is a colorless and odorless gas. It can cause unconsciousness or even death.

D Make sure the exhaust system has no holes or loose connections. The system should be checked from time to time. If you hit something, or notice a change in the sound of the the system exhaust, have checked immediately.

D Do not run the engine in a garage or enclosed area except the time needed to drive the vehicle in or out. The exhaust gases cannot escape, making this a particularly dangerous situation.

for

D Do not remain for a long time in a parked vehicle with the engine run- ning. If it is unavoidable, however, do so only in an unconfined area and adjust the heating or cooling system to force outside air into the vehicle.

in

z Keep your engine in good running order. Malfunctions the engine electrical system, electronic ignition system/distributor ignition system or fuel system could cause an ex- tremely high three−way catalytic converter temperature.

z If the engine becomes difficult to start or stalls frequently, take your vehicle in for a check−up as soon as possible. Remember, your Toyota dealer knows your vehicle and its three−way catalytic converter sys- tem best.

z To ensure that the three−way cata- lytic converter and the entire emis- sion control system operate proper- ly, your vehicle must receive the periodic inspections required by the Toyota Maintenance Schedule. For scheduled maintenance information, refer to the “Scheduled Maintenance Guide” or “Owner’s Manual Supple- ment”.

202

D Keep

the

trunk

lid closed while driving. An open or unsealed trunk lid may cause exhaust gases to be drawn into the vehicle.

D To allow proper operation of your vehicle’s ventilation system, keep the inlet grilles in front of the wind- shield clear of snow, leaves, or oth- er obstructions.

D If you smell exhaust fumes in the vehicle, drive with the windows open and the trunk lid closed. Have the cause immediately located and corrected.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

Facts about engine oil consumption FUNCTIONS OF ENGINE OIL Engine oil has the primary functions of lubricating and cooling the inside of the engine, and plays a major role in main- taining the engine in proper working order. ENGINE OIL CONSUMPTION It is normal that an engine should con- sume some engine oil during normal engine operation. The causes of oil consumption in a normal engine are as follows. D Oil is used to lubricate pistons, piston rings and cylinders. A thin film of oil is left on the cylinder wall when a pis- ton moves downwards in the cylinder. High negative pressure generated when the vehicle is decelerating sucks some of this oil into the combustion chamber. This oil as well as some part of the oil film left on the cylinder wall is burned by temperature combustion gases during the combustion process. D Oil is also used to lubricate the stems of the intake valves. Some of this oil is sucked into the combustion chamber together with is burned along with the fuel. High tem- perature exhaust gases also burn the oil used to lubricate the exhaust valve stems.

intake air and

the high

the

’04Camry_U (L/O 0307)

The amount of engine oil consumed de- pends on the viscosity of the oil, the quality of the oil and the conditions the vehicle is driven under. More oil is consumed by high−speed driv- ing and frequent acceleration and decel- eration. A new engine consumes more oil, since its pistons, piston rings and cylinder walls have not become conditioned. Oil consumption: Max. 1.0 L per 1000
km (1.1 qt./600 miles, 0.9 lmp. qt./600
miles) When judging the amount of oil con- sumption, note that the oil may become diluted and make it difficult to judge the true level accurately. As an example, if a vehicle is used for repeated short trips, and consumes a nor- mal amount of oil, the dipstick may not show any drop in the oil level at all, even after 1000 km (600 miles) or more. This is because the oil is gradually becoming diluted with fuel or moisture, making it appear that the oil level has not changed. The diluting ingredients evaporate out when the vehicle is then driven at high speeds, as on an express way, making it appear that oil is excessively consumed after driving at high speeds.

IMPORTANCE OF ENGINE OIL LEVEL CHECK One of the most important points in prop- er vehicle maintenance is to keep the en- gine oil at the optimum level so that oil function will not be impaired. Therefore, it is essential that the oil level be checked regularly. Toyota recommends that the oil level be checked every time you refuel the vehicle.

NOTICE

Failure to check the oil level regularly could lead to serious engine trouble due to insufficient oil.

For detailed information on oil level check, see “Checking level” on page 282 in Section 7−2.

the engine oil

203

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

Iridium−tipped spark plugs

Your engine is fitted with iridium−tipped spark plugs.

NOTICE

Use only iridium−tipped spark plugs and do not adjust gaps for your en- gine performance and smooth drive- ability.

204

’04Camry_U (L/O 0307)

Brake system The tandem master cylinder brake system is a hydraulic system with two separate sub−systems. If either sub−system should fail, the other will still work. However, the pedal will be harder to press, and your stopping distance will increase. Also, the brake system warning light may come on.

CAUTION

Do not drive your vehicle with only a single brake system. Have your brakes fixed immediately.

CAUTION

D Do not pump the brake pedal if the engine stalls. Each push on the pedal uses up your reserved vacu- um.

lost,

D Even if the power assist

is com- pletely the brakes will still work. But you will have to push the pedal hard, much harder than nor- mal. And your braking distance will increase.

the brakes.

BRAKE BOOSTER The brake booster uses engine vacuum to power−assist the engine should quit while you are driving, you can bring the vehicle to a stop with normal pedal pressure. There is enough reserved vacuum two stops—but no more!

for one or

If

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

(with

ANTI−LOCK BRAKE SYSTEM “ABS” warning light) The anti−lock brake system is designed to help prevent lock−up of the wheels during a sudden braking or braking on slippery road surfaces. This assists in providing directional stability and steer- ing performance of the vehicle under these circumstances.

this situation,

Effective way to press the ABS brake pedal: When the anti−lock brake system function is in action, you may feel the brake pedal pulsating and hear a noise. In the anti−lock brake system work for you, just hold the brake pedal down more firmly. Do not pump the brake in a panic stop. This will reduced braking perfor- mance.

result

let

to

in

The anti−lock brake system becomes op- erative after the vehicle has accelerated to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the vehicle decelerates to a speed below approximately 5 km/h (3 mph).

’04Camry_U (L/O 0307)

CAUTION

Do not overestimate the anti−lock brake system: Although the anti−lock brake system assists in providing ve- hicle control, it is still important to drive with all due care and maintain a moderate speed and safe distance from the vehicle in front of you, be- cause there are limits to the vehicle stability and effectiveness of steering wheel operation even with the anti− lock brake system on. If tire grip performance exceeds its capability, or if hydroplaning occurs during high speed driving in the rain, the anti−lock brake system does not provide vehicle control.

Depressing the brake pedal on slippery road surfaces such as on a manhole cov- er, a steel plate at a construction site, joints in a bridge, etc. on a rainy day tends to activate the anti−lock brake sys- tem. You may hear a click or motor sound in the engine compartment for a few seconds when the engine is started or just after the vehicle begins to move. This means that the anti−lock brake system is in the self−check mode, and does not indicate a malfunction. When the anti−lock brake system is ac- tivated, the following conditions may occur. They do not indicate a malfunc- tion of the system: D You may hear the anti−lock brake sys- tem operating and feel the brake pedal pulsating and the vibrations of the ve- hicle body and steering wheel. You may also hear the motor sound in the engine compartment even after the ve- hicle is stopped.

D At the end of the anti−lock brake sys- the brake pedal may

tem activation, move a little forward.

205

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

the vehicle

Anti−lock brake system is not de- signed to shorten the stopping dis- tance: Always drive at a moderate speed and maintain a safe distance from front of you. Compared with vehicles without an anti−lock brake system, your vehicle may require a longer stopping dis- tance in the following cases: D Driving on rough, gravel or snow−

in

covered roads.

D Driving with tire chains installed. D Driving over the steps such as the

joints on the road.

D Driving on roads where the road surface is pitted or has other differ- ences in surface height.

Install all 4 tires of specified size at appropriate pressure: The anti−lock brake system detects vehicle speeds using the speed sensors for respec- tive wheels’ turning speeds. The use of tires other than specified may fail to detect the accurate turning speed resulting longer stopping dis- tance.

in a

Type A

Type B

206

’04Camry_U (L/O 0307)

“ABS” warning light (vehicles without vehicle stability control system) The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system works properly, the light turns off after a few seconds. There- after, if the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate, but the brake system still operates con- ventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces. the following conditions If either of occurs, indicates a malfunction this somewhere in the parts monitored by the warning light. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.

D The light comes on while you are driv-

ing.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

if

few seconds. Thereafter,

A warning light turning on briefly during operation does not indicate a problem. “ABS” warning light (vehicles with ve- hicle stability control system) The light comes on when the ignition key is turned to the “ON” position. If the anti− lock brake system and the brake assist system work properly, the light turns off after a the system malfunctions, the light comes on again. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system, the brake assist system, the traction control system and the vehicle stability control system do not operate, but the brake system still oper- ates conventionally. When the “ABS” warning light is on (and the brake system warning light is off), the anti−lock brake system does not operate so that the wheels could lock up during a sudden braking or braking on slippery road surfaces.

If either of the following conditions oc- curs, this indicates a malfunction some- where in the components monitored by the warning light system. Contact your Toyota dealer as soon as possible to service the vehicle. D The light does not come on when the ignition key is turned to the “ON” posi- tion, or remains on.

D The light comes on while you are driv-

ing.

A warning light turning on briefly during operation does not indicate a problem.

CAUTION

If the “ABS” warning light remains on together with the brake system warn- ing light, immediately stop your ve- hicle at a safe place and contact your Toyota dealer. In this case, not only the anti−lock brake system will fail but also the vehicle will become extremely unsta- ble during braking.

the brakes on,

DRUM−IN−DISC TYPE PARKING BRAKE SYSTEM (on some models) type Your vehicle has a drum−in−disc parking brake system. This type of brake system needs bedding−down of the brake shoes periodically or whenever the parking brake shoes and/or drums are replaced. Have your Toyota dealer perform the bed- ding−down. BRAKE ASSIST SYSTEM (vehicles with vehicle stability control system) the When you slam brake assist system judges as an emer- gency stop and provides more powerful braking for a driver who cannot hold down the brake pedal firmly. When you slam the brakes on, more pow- erful braking will be applied. At this time, you may hear a sound the engine compartment and feel the vibrations of the brake pedal. This does not indicate a mal- function. The brake assist system becomes opera- tive after the vehicle has accelerated to a speed in excess of approximately 10
km/h (6 mph). It stops operating when the vehicle decelerates to a speed below approximately 5 km/h (3 mph).

in

207

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Brake pad wear limit indicators

Your Toyota’s identification— —Vehicle identification number

For an explanation of this system’s warn- ing light, see “Service reminder indicators and warning buzzers” on page 111 in Sec- tion 1−6.

The brake pad wear limit indicators on your disc brakes give a warning noise when the brake pads are worn to where replacement is required. If you hear a squealing or scraping noise while driving, have the brake pads checked and replaced by your Toyota dealer as soon as possible. Expensive ro- tor damage can result if the pads are not replaced when necessary.

The vehicle identification number (VIN) is the legal identifier for your vehicle. This number is on the left top of the instrument panel, and can be seen through the windshield from outside. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

208

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Engine number

The engine number is stamped on the engine block as shown.

The vehicle identification number (VIN) is also on the Certification Label.

2AZ−FE engine

1MZ−FE and 3MZ−FE engines

209

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Suspension and chassis

CAUTION

Do not modify the suspension/chassis with lift kits, spacers, springs, etc. It can cause dangerous vehicle handling characteristics, resulting loss of control.

in

Theft prevention labels Your new vehicle carries theft preven- tion labels which are approximately 56
mm (2.20 in.) by 16 mm (0.63 in.). The purpose of these labels is to reduce the incidence of vehicle thefts by facilitat- ing the tracing and recovery of parts from stolen vehicles. The label is designed so that once it is applied to a surface, any attempt to remove it will result in destroy- ing the integrity of the label. Transferring these labels intact from one part to anoth- er, will be impossible.

NOTICE

You should not attempt to remove the theft prevention labels as it may vio- late certain state or federal laws.

210

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

Tire information— —Tire symbols

’04Camry_U (L/O 0307)

This illustration indicates typical tire symbols. 1. Tire size—For details, see “—Tire

size” on page 213.

2. DOT and Tire

Identification Number (TIN)—For details, see “—DOT and Tire Identification Number (TIN)” on page 212.

tire

quality

3. Uniform

gra- ding—For details, see “Uniform tire quality grading” that follows. 4. The location of the tread wear indicators—For see “Checking and replacing tires” on page 290.

details,

5. Tire ply composition and mate- rials—Plies mean a layer of rub- ber−coated parallel cords. Cords mean the strands forming the plies in the tire.

6. Radial tires or bias−ply tires—A radial tire has “RADIAL” on the sidewall. The tire not marked with “RADIAL” is a bias−ply tire.

211

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—DOT and Tire Identification Number (TIN)

The “DOT” symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.

This illustration indicates typical DOT and Tire Identification Number (TIN). 1. “DOT” symbol 2. Tire Identification Number (TIN) 3. Tire manufacturer’s identification

mark

4. Tire size code 5. Manufacturer’s optional tire type

code

6. Manufacturing week 7. Manufacturing year

7. “TUBELESS”

or

“TUBE TYPE”—A tubeless tire does not have a tube inside the tire and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube maintains the air pressure.

8. Load limit at maximum cold tire inflation pressure—For details, see “Checking and replacing tires” on page 290.

9. Maximum cold

tire

tire

cold

inflation pressure—This means the pres- sure to which a tire may be in- flated. For details about recom- mended inflation pressure, see “Tires” on page 312. tire or all season tire—An all season tire has “M+S” on tire not marked with “M+S” is a summer tire. For details, see “Types of tires” on page 222.

the sidewall. The

10.Summer

212

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Tire size

—Name of each section of tire

This illustration indicates typical tire size. 1. Tire use

(P=Passenger car,

T=Temporary use)

2. Section width (in millimeters) 3. Aspect ratio (tire height to section

width)

4. Tire construction code (R=Radial,

D=Diagonal)

5. Wheel diameter (in inch) 6. Load index (2 digits or 3 digits) 7. Speed symbol (alphabet with one

letter)

1. Section width 2. Tire height 3. Wheel diameter

1. Bead 2. Sidewall 3. Shoulder 4. Tread 5. Belt 6. Inner liner 7. Reinforcing rubber 8. Carcass 9. Rim lines 10.Bead wires 11. Chafer

213

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

—Uniform tire quality grading This information has been prepared in accordance with regulations issued by the National Highway Traffic Safe- ty Administration of the U.S. Depart- ment of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with in- formation on uniform tire quality grad- ing. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades—All passenger vehicle tires must conform to Fed- eral Safety Requirements in addi- tion these grades. Quality grades can be found where appli- cable on the tire sidewall between tread shoulder and maximum sec- tion width. For example: Treadwear 200 Traction AA Temperature A

to

214

’04Camry_U (L/O 0307)

Treadwear—The treadwear grade is a comparative rating based on the wear rate of the tire when tested un- der controlled conditions on a speci- fied government test course. For ex- ample, a tire graded 150 would wear one and a half (1−1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving hab- its, service practices and differences in road characteristics and climate.

Traction AA, A, B, C—The traction grades, from highest to lowest, are AA, A, B, and C, and they represent the tire’s ability to stop on wet pave- ment as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor trac- tion performance. Warning: The traction grade assigned to tire is based on braking (straight ahead) traction tests and does not include cornering (turning) traction.

this

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Temperature A, B, C—The tempera- ture grades are A (the highest), B, and C, representing the tire’s resis- tance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a specified indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C cor- responds to a level of performance which all passenger car tires must meet under the Federal Motor Vehicle Safety Standard No.109. Grades B and A represent higher levels of per- formance on the laboratory test wheel than the minimum required by law. Warning: The temperature grades for this tire are established for a tire that is properly inflated and not over- loaded. Excessive speed, underinfla- tion, or excessive loading, either sep- arately or in combination, can cause heat buildup and possible tire failure.

215

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

—Tire related terms

Cold tire inflation pressure

Maximum inflation pressure

Recommended inflation pressure

Accessory weight

Curb weight

Maximum loaded vehicle weight

Normal occupant weight

Tire inflation pressure when the vehicle has been parked at least 3 hours or more, or it has not been driven more than 1.5 km or 1 mile under that condition The maximum cold inflation pressure to which a tire may be inflated and shown on the sidewall of the tire Cold tire inflation pressure recommended by a manufacturer The combined weight (in excess of those standard items which may be replaced) of automatic transmission, power steering, power brakes, power windows, power seats, radio, and heater, to the extent that these items are available as factory−installed equipment (whether installed or not) The weight of a motor vehicle with standard equipment including the maximum capacity of fuel, oil, and coolant, and, if so equipped, air conditioning and additional weight optional engine The sum of— (a) Curb weight; (b) Accessory weight; (c) Vehicle capacity weight; and (d) Production options weight

68 kg (150 lb.) times the number of occupants specified in the second column of Table 1 on page 218

216

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Production options weight

Vehicle capacity weight (Total load capacity)

Intended outboard sidewall

Occupant distribution

Rim

Rim diameter (Wheel diameter) Rim size designation Rim type designation Rim width

Vehicle maximum load on the tire

The combined weight of those installed regular production options weighing over 2.3 kg (5 lb.) in excess of those standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim The rated cargo and luggage load plus 68 kg (150 lb.) times the vehicle’s designated seating capacity (A) The sidewall that contains a whitewall, bears white lettering or bears

manufacturer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or

(B) The outward facing sidewall of an asymmetrical tire that has a particular

side that must always face outward when mounted on a vehicle

Distribution of occupants in a vehicle as specified in the third column of Table 1 that follows A metal support for a tire or a tire and tube assembly upon which the tire beads are seated Nominal diameter of the bead seat Rim diameter and width The industry of manufacturer’s designation for a rim by style or code Nominal distance between rim flanges The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight and dividing by two

217

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Vehicle normal load on the tire

Weather side

The load on an individual tire that is determined by distributing to each axle its share of the curb weight, accessory weight, and normal occupant weight (distributed in accordance with Table 1 that follows) and dividing by two The surface area of the rim not covered by the inflated tire

Table 1—Occupant loading and distribution for vehicle normal load for various designated seating capacities

Designated seating capacity,

number of occupants

Vehicle normal load, number of

occupants

Occupant distribution in a normally

loaded vehicle

2 through 4
5 through 10

2 in front 2 in front, 1 in second seat

218

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

Vehicle load limits Vehicle load limits include total load capacity, seating capacity, towing ca- pacity and cargo capacity. Follow the load limits shown below. Total load capacity:

410 kg (900 lb.) Total load capacity means com- bined weight of occupants, cargo and luggage. Tongue load is in- cluded when trailer towing.

Seating capacity:

Total 5 (Front 2, Rear 3) Seating capacity means the maxi- mum number of occupants whose weight is supposed to be 68 kg (150
lb.) per person. Depending on the weight of person, the seating ca- pacity given may exceed the total load capacity.

NOTICE

Even if the number of occupants are within the seating capacity, do not exceed the total load ca- pacity.

Towing capacity: 907 kg (2000 lb.) Towing capacity means the maxi- mum gross trailer weight (trailer weight plus its cargo weight) that your vehicle is able to tow.

Cargo capacity Cargo capacity may increase or de- crease depending on the size (weight) and the number of occupants. For de- tails, see “Capacity and distribution” that follows.

CAUTION

Do not apply the load more than each load limit. That may cause not only damage to the tires, but also deterioration to the steering ability and braking ability, which may cause an accident.

Cargo and luggage— —Stowage precautions When stowing cargo and luggage in the vehicle, observe the following: D Put cargo and luggage in the trunk when at all possible. Be sure all items are secured in place.

D Be careful to keep the vehicle bal- anced. Locating the weight as far forward as possible helps maintain balance.

D For better fuel economy, do not

carry unneeded weight.

219

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

D Do not drive with objects left on top of the instrument panel. They may interfere with the driver’s field of view. Or they may move during sharp vehicle acceleration or turning, and im- pair the driver’s control of the vehicle. In an accident they may injure the vehicle occu- pants.

CAUTION

D To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep car- go and luggage low, as close to the floor as possible.

D Never allow anyone to ride in the enlarged trunk. It is not de- signed for passengers. They should ride in their seats with their seat belts properly fas- tened. Otherwise, they are much more likely to suffer seri- ous bodily injury, in the event of sudden braking or a colli- sion.

D Do not place anything on the package tray behind the rear seatback. Such items may be thrown about and possibly in- jure people in the vehicle dur- ing sudden braking or an acci- dent.

220

FOR

—Capacity and distribution Cargo capacity depends on the to- tal weight of the occupants. (Cargo capacity) = (Total load capac- ity) – (Total weight of occupants) STEPS CORRECT LOAD LIMIT 1. Locate the statement “The com- bined weight of occupants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle.

DETERMINING

3. Subtract the combined weight of the driver and passengers from XXX kilograms or XXX pounds.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

4. The resulting figure equals the available amount of cargo and lug- gage load capacity. For example, if the “XXX” amount equals 1400
lbs. and there will be five 150 lb. passengers in your vehicle, the amount of available cargo and lug- gage load capacity is 650 lbs. (1400–750 (5x150)=650 lbs).

5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available car- go and luggage load capacity of your vehicle.

For details about trailer towing, see page 228.

Cargo capacity

Total load capacity

EXAMPLE ON YOUR VEHICLE In case that 2 people with the com- bined weight of 166 kg (366 lb.) are riding in your vehicle with the total load capacity of 410 kg (900 lb.), the available amount of cargo and lug- gage load capacity will be as follows: 410 kg – 166 kg = 244 kg. (900 lb. – 366 lb. = 534 lb.) From this condition, if 3 more passen- gers with the combined weight of 176
kg (388 lb.) get on, the available car- go and luggage load will be reduced as follows:

244 kg – 176 kg = 68 kg. (534 lb. – 388 lb. = 146 lb.) As shown in the above example, if the number of occupants increases, the cargo and luggage load equaling the combined weight of occupants who got on later must be reduced. In other words, if the increase in the number of occupants causes the excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you have to reduce the cargo and luggage on your vehicle. For details about total load capacity, see “Vehicle load limits” on page 219.

221

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

CAUTION

Even if the total load of occu- pant’s weight and the cargo load is less than the total load capac- ity, do not apply the load uneven- ly. That may cause not only dam- age to the tire but also deteriora- tion to the steering ability due to unbalance of the vehicle, causing an accident.

’04Camry_U (L/O 0307)

Types of tires Determine what kind of tires your vehicle is originally equipped with. 1. Summer tires Summer tires are high−speed capabil- ity tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow−covered or icy roads. For driving on snow−covered or icy roads, we recommend using snow tires. If installing snow tires, be sure to replace all four tires. 2. All season tires All season tires are designed to pro- vide better traction in snow and to be adequate for driving in most winter conditions, as well as for use all year round.

traction

All season tires, however, do not have adequate performance compared with snow tires in heavy or loose snow. Also, all season tires fall short in acceleration and handling performance compared with summer tires in highway driving. The details about how to distinguish summer tires from all season tires are described on page 211.

CAUTION

D Do not mix summer and all sea- son tires on your vehicle as this can cause dangerous han- dling characteristics, resulting in loss of control.

D Do not use tires other than the manufacturer’s designated tires, and never mix tires or wheels of the sizes different from the originally equipped tires and wheels.

222

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

SECTION 3

STARTING AND DRIVING Starting and driving Before starting the engine How to start the engine Tips for driving in various conditions Winter driving tips Dinghy towing Trailer towing How to save fuel and make your vehicle last longer

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

224
224
225
226
227
228
234

223

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

How to start the engine— (a) Before cranking 1. Apply the parking brake firmly. 2. Turn off unnecessary lights and acces-

sories.

into neutral. Hold

3. Manual transmission: Press the clutch pedal to the floor and shift the trans- mission the clutch pedal to the floor until the engine is started. A starter safety device will pre- vent the starter from operating if the clutch pedal is not fully depressed. Automatic transmission: Put the se- lector lever in “P”. If you need to re- start the engine while the vehicle is moving, put the selector lever in “N”. A starter safety device will prevent the starter the selector lever is in any drive position.

from operating if

4. Automatic

transmission only: De- press the brake pedal and hold it to the floor until driving off.

Before starting the engine 1. Check the area around the vehicle be-

fore entering it.

2. Adjust seat position, seatback angle, restraint

seat cushion height, head height and steering wheel angle.

3. Vehicles with the power adjustable ped- als—Adjust the position of the acceler- ator and brake pedals.

4. Adjust the inside and outside rear view

mirrors.

5. Lock all doors. 6. Fasten seat belts.

224

(b) Starting the engine Before starting the engine, be sure to fol- low the instructions in “(a) Before crank- ing”. Normal starting procedure The multiport fuel injection system/sequen- tial multiport fuel injection system in your engine automatically controls the proper air−fuel mixture for starting. You can start a cold or hot engine as follows: With your foot off the accelerator pedal, crank the engine by turning the key to “START”. Release the engine starts. Engine should be warmed up by driving, not in idle. For warming up, drive with smoothly turning engine until engine cool- ant temperature is within normal range. If the engine stalls... Simply restart it, using the correct proce- dure given in normal starting. If the engine will not start... See “If your vehicle will not start” on page 238 in Section 4.

it when

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

NOTICE

z Do not crank for more than 30 se- conds at a time. This may overheat the starter and wiring systems.

z Do not race a cold engine. z If the engine becomes difficult to start or stalls frequently, have the engine checked immediately.

Tips for driving in various conditions D Always slow down in gusty crosswinds. This will allow you much better control. D Drive slowly onto curbs and, if pos- sible, at a right angle. Avoid driving onto high, sharp−edged objects and other road hazards. Failure to do so can lead to severe tire damage such as a tire burst. Drive slowly when passing over bumps or travelling on a bumpy road. Other- wise, the impact could cause severe damage to the tires and/or wheels.

they

D When parking on a hill, turn the front wheels until touch the curb so that the vehicle will not roll. Apply the parking brake, and place the transmis- sion in “P” (automatic) or in first or reverse (manual). If necessary, block the wheels.

D Washing your vehicle or driving through deep water may get the brakes wet. To see whether they are wet, check that there is no traffic near you, and then press the pedal lightly. If you do not feel a normal braking force, the brakes are probably wet. To dry them, drive the vehicle cautiously while lightly pressing the brake pedal with the park- ing brake applied. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.

CAUTION

D Before driving off, make sure that the parking brake is fully released and reminder light is off.

the parking brake

D Do not

leave your vehicle unat- tended while the engine is running. D Do not rest your foot on the brake pedal while driving. It can cause dangerous overheating, needless wear, and poor fuel economy.

D To drive down a long or steep hill, reduce your speed and downshift. Remember, if you ride the brakes excessively, they may overheat and not work properly.

225

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

D Be careful when accelerating, up- shifting, downshifting or braking on a slippery surface. Sudden accelera- tion or engine braking could cause the vehicle to spin or skid.

tire dealer

D Do not drive in excess of the speed limit. Even if the legal speed limit permits it, do not drive over 140
km/h (85 mph) unless your vehicle has high−speed capability tires. Driving over 140 km/h (85 mph) may result in tire failure, loss of control and possible injury. Be sure to con- sult a to determine whether the tires on your vehicle are high−speed capability tires or not before driving at such speeds. D Do not continue normal driving when the brakes are wet. If they are require a wet, your vehicle will longer stopping distance, and it may pull the brakes are applied. Also, the park- ing brake will not hold the vehicle securely.

to one side when

226

’04Camry_U (L/O 0307)

Winter driving tips Make sure your coolant is properly pro- tected against freezing. Only use “Toyota Super Long Life Coolant” or similar high quality ethylene glycol based non−silicate, non−amine, non−nitrite, and non−borate coolant with long−life hy- brid organic acid technology. See “Checking the engine coolant level” on page 284 in Section 7−2 for details of coolant type selection. “Toyota Super Long Life Coolant” is pre− mixed with 50% coolant and 50% deion- ized water. This coolant provides protec- tion down to about −35_C (−31_F).

NOTICE

Do not use plain water alone.

Check the condition of the battery and cables. Cold temperatures reduce the capacity of any battery, so it must be in top shape to provide enough power for winter start- ing. Section 7−3 tells you how to visually inspect the battery. Your Toyota dealer and most service stations will be pleased to check the level of charge.

Make sure the engine oil viscosity is suitable for the cold weather. See page 282 in Section 7−2 for recom- mended viscosity. Leaving a heavy sum- mer oil in your vehicle during winter months may cause harder starting. If you are not sure about which oil to use, call your Toyota dealer—he will be pleased to help. Keep the door locks from freezing. Squirt lock de−icer or glycerine into the locks to keep them from freezing. Use a washer fluid containing an anti- freeze solution. This product is available at your Toyota dealer and most auto parts stores. Follow the manufacturer’s directions for how much to mix with water.

NOTICE

Do not use engine antifreeze or any other substitute because it may dam- age your vehicle’s paint.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

into

in and around

Do not use your parking brake when there is a possibility it could freeze. When parking, put the transmission into “P” (automatic) or first or reverse (manual) and block the rear wheels. Do not use the parking brake, or snow or water accumulated the freeze, parking brake mechanism may making it hard to release. Keep ice and snow from accumulating under the fenders. Ice and snow built up under your fenders can make steering difficult. During bad winter driving, stop and check under the fenders occasionally. Depending on where you are driving, we recommend you carry some emer- gency equipment. Some of the things you might put in the vehicle are tire chains, window scraper, bag of sand or salt, flares, small shovel, jumper cables, etc.

’04Camry_U (L/O 0307)

Dinghy towing (with automatic transmission)

Dinghy towing (with manual transmission)

Your vehicle to be dinghy towed (with four wheels on the ground) behind a motorhome.

is not designed

Your vehicle can be dinghy towed (with four wheels on the ground) from the front behind a motorhome.

NOTICE

CAUTION

Do not tow your vehicle with four wheels on the ground. This may cause serious damage to your vehicle.

Dinghy towing requires special equip- ment and accessories. Please refer to your service outlet of the motorhome manufacture recommended equipment.

the

for

NOTICE

Dinghy towing does not eliminate the possibility of damage to your vehicle.

227

2004 CAMRY from Jul. ’03 Prod. (OM33616U)

’04Camry_U (L/O 0307)

DINGHY TOWING TIPS Before dinghy towing, be sure to ob- serve the following in order to reduce the damage to your vehicle. 1. Put the shift lever in neutral. 2. Turn the ignition switch to the “ACC” position. Make sure the audio is turned off and any item is not plugged into the power outlet.

NOTICE

To avoid the locking of the steering wheel, turn the ignition switch to the “ACC” position.

3. Release the parking brake. After dinghy towing, let the engine idle for more than 3 minutes before driving the vehicle.

228

NOTICE

Do not tow your vehicle from the rear. This may cause serious damage to your vehicle.

vehicle. Towing

Trailer towing Your vehicle is designed primarily as a passenger−carrying trailer will have an adverse effect on handling, performance, braking, durability and driving economy (fuel consumption, etc.). Your safety and satisfaction depend on the proper use of correct equipment and cautious driving habits. For your safety and the safety of others, you must not overload your vehicle or trailer. Toyota warranties do not apply to damage or malfunction caused by towing a trailer for commercial purposes. Ask your local further details before Toyota dealer towing.

for

NOTICE

When towing a trailer, be sure to con- sult your Toyota dealer for further in- formation on additional requirements such as a towing kit, etc.

2004 CAMRY from Jul. ’03 Prod. (OM33616U)