2009 Toyota Camry HV Owners Manual

l Do not leave the hybrid system operating in an area with snow build-up, or where it is snowing. If snowbanks build up around the vehicle while the hybrid system is operating, exhaust gases may collect and enter the vehi- cle. This may lead to death or a serious health hazard.

n Exhaust gases

Exhaust gases include harmful carbon monoxide (CO) that is colorless and odorless. Inhaling exhaust gases may lead to death or a serious health haz- ard.

If the vehicle is in a poorly ventilated area, stop the hybrid system. In a closed area, such as a garage, exhaust gases may collect and enter the vehicle. This may lead to death or a serious health hazard.

l The exhaust should be checked occasionally. If there is a hole or crack caused by corrosion, damage to a joint or abnormal exhaust noise, be sure to have the vehicle inspected and repaired by your Toyota dealer. Failure to do so may allow exhaust gases to enter the vehicle, resulting in death or a serious health hazard.

127

2-1. Driving procedures

CAUTION

n When taking a nap in the vehicle

Always turn the hybrid system off. Otherwise, you may accidentally move the shift lever or depress the accelerator pedal, which could cause an accident or fire due to hybrid system overheating. Additionally, if the vehicle is parked in a poorly ventilated area, exhaust gases may collect and enter the vehicle, leading to death or a serious health hazard.

n When braking the vehicle

l When the brakes are wet, drive more cautiously. Braking distance increases when the brakes are wet, and may cause one side of the vehicle to brake differently than the other side. Also the parking brake may not securely hold the vehicle. If the electronically controlled brake system does not operate, do not fol- low other vehicles closely and avoid downhills or sharp turns that require braking. In this case, braking is still possible, but it will require more force on the pedal than usual. Braking distance may also increase.

l The brake system consists of 3 individual hydraulic systems: If one of the systems fails, the others will still operate. In this case, the brake pedal should be depressed more firmly than usual and braking distance becomes longer. Do not drive your vehicle if any hydraulic circuit has failed. Have your brakes fixed immediately.

128

2-1. Driving procedures

NOTICE

n When driving the vehicle

Do not use the accelerator pedal or depress the accelerator and brake ped- als together to hold the vehicle on a hill.

n When parking the vehicle

Always put the shift lever in P. Failure to do so may cause the vehicle to move or the vehicle may accelerate suddenly if the accelerator pedal is acci- dentally depressed.

n Avoiding damage to vehicle parts

l Do not turn the steering wheel fully in either direction and hold it there for a

long time. Doing so may damage the power steering motor.

l When driving over bumps in the road, drive as slowly as possible to avoid

damaging the wheels, underside of the vehicle, etc.

n If you hear a squealing or scraping noise (brake pad wear limit indica-

tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage can result if the pads are not replaced when needed. It is dangerous to drive the vehicle when the wear limits of the brake pads and/or that of the brake discs are exceeded.

n If you get a flat tire while driving

A flat or damaged tire may cause the following situations. Hold the steering wheel firmly and gradually press the brake pedal to slow down the vehicle. It may be difficult to control your vehicle. l The vehicle will make abnormal sounds. l The vehicle will behave abnormally. Replace a flat tire with a new one. (→P. 370)

129

2-1. Driving procedures

NOTICE

n When encountering flooded roads

Do not drive on a road that has flooded after heavy rain etc. Doing so may cause the following serious damage to the vehicle. l Engine stalling l Short in electrical components l Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following. l Brake function l Changes in quantity and quality of oil and fluid used for the engine, hybrid

system transaxle, etc.

l Lubricant condition for the bearings and suspension joints (where possi-

ble) and the function of all joints, bearings, etc.

130

2-1. Driving procedures Power (ignition) switch

Modes can be switched by pressing the “POWER” switch when car- rying the electronic key on your person. (The hybrid system can be started in any mode by operating the “POWER” switch at the same time as depressing the brake pedal.) n Starting the hybrid system STEP 1

Check that the parking brake is set. Check that the shift lever is set in P. Sit in the driver’s seat and firmly depress the brake pedal. The “POWER” switch indicator turns green. If the indicator does not turn green, the hybrid system cannot be started.

STEP 2

STEP 3

STEP 4

Press the “POWER” switch.

After a while, the “READY” indicator comes on with a beep sound. The vehicle can move when the “READY” indicator is on even if the engine is stopped.

131

2-1. Driving procedures

n Changing “POWER” switch mode

OFF* Emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “POWER” switch indicator turns amber. ON mode All electrical components can be used. The “POWER” switch indicator turns amber. *: If the shift lever is in a posi- tion other than P when turn- ing off the hybrid system, the “POWER” switch will be turned to ACCESSORY mode, not to OFF.

132

n Steering lock release

2-1. Driving procedures

Make sure that the steering wheel lock is released. To release the steering wheel lock, gently turn the wheel left or right while pressing the “POWER” switch. If the steering wheel lock does not release, the “POWER” switch indicator will flash green.

n If the hybrid system does not start

The immobilizer system may not have been deactivated. (→P. 83)

n When the “POWER” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toy- ota dealer immediately.

n If the “READY” indicator does not come on

If the “READY” indicator does not come on when you press the “POWER” switch with the shift lever in P and the brake pedal depressed, contact your Toyota dealer immediately. n Auto power off function

If the vehicle is left in ACCESSORY mode for more than an hour with the shift lever in P, the “POWER” switch will automatically turn off.

n When the ambient temperature is low, such as during winter driving

conditions It may take time until the “READY” indicator comes on. n Sounds and vibrations specific to a hybrid vehicle

→P. 24

n When the hybrid system is malfunctioning

→P. 349

n Electronic key battery depletion

→P. 42

133

2-1. Driving procedures

n When the electronic key battery is discharged

→P. 322

n Conditions affecting operation

→P. 40

n Note for the smart key system

→P. 42

CAUTION

n When starting the hybrid system

Always start the hybrid system while sitting in the driver's seat. Do not depress the accelerator pedal while starting the hybrid system under any cir- cumstances. Doing so may cause an accident resulting in death or serious injury.

n Stopping the hybrid system in an emergency

If you want to stop the hybrid system in an emergency while driving the vehi- cle, push and hold the “POWER” switch for more than 3 seconds. However, do not touch the “POWER” switch while driving except in an emer- gency. If the hybrid system stops while the vehicle is being driven, this could lead to an unexpected accident.

NOTICE

n To prevent the 12-volt battery from being discharged

Do not leave the “POWER” switch in ACCESSORY or ON mode for long periods without the hybrid system on.

n When starting the hybrid system

l Do not race a cold engine.

If the hybrid system becomes difficult to start, have the hybrid system checked immediately.

134

2-1. Driving procedures Transmission

Select a shift position appropriate for the driving conditions. n Shifting the shift lever

the

While “POWER” switch is in ON mode, depress brake pedal and move the shift lever.

the

135

2-1. Driving procedures

n Shift position uses

Shift position

Function

Parking the vehicle or starting the hybrid system

Reversing Neutral

Normal driving

Position for engine braking

n When in heavy traffic

If the shift lever is in N, the hybrid battery (traction battery) will not be charged. To help prevent the battery from discharging, avoid putting the shift lever in N for an extended period of time.

n If the shift lever cannot be shifted from P

→P. 380

136

2

2-1. Driving procedures Turn signal lever

Left turn Right turn Move and hold the lever partway to signal a lane change. The left hand signal will flash until you release the lever. Move and hold the lever partway to signal a lane change. The right hand signal will flash until you release the lever.

n Turn signals can be operated when The “POWER” switch is in ON mode.

n If the indicators flash faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

137

2-1. Driving procedures Parking brake

U.S.A. Canada

Sets the parking brake* (Depressing the pedal again releases the parking brake.)

*: Fully depress

the parking brake pedal with your left foot while depressing the brake pedal with your right foot.

NOTICE

n Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

138

2-2. Instrument cluster Gauges and meters

The following gauges, meters and displays illuminate when the “POWER” switch is in ON mode.

Engine coolant temperature gauge Displays the engine coolant temperature. Fuel economy meter Displays the current fuel consumption in analog form when the hybrid system is operating. When only the electric motor (traction motor) powers the vehicle, the needle indicates “E-MODE”. Speedometer Displays the vehicle speed. Fuel gauge Displays the quantity of fuel remaining in the tank. Odometer/trip meter/instrument panel light control and trip meter reset button Switches between odometer and trip meter. Pushing and holding the button when the trip meter is being displayed will reset the trip meter. Instrument panel light control: →P. 145
Multi-information display →P. 145

139

2-2. Instrument cluster

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker When the headlight switch is turned on, the brightness will be reduced slightly unless the control dial fully clockwise.

turned

is

n Eco drive level

The brightness of the arcs around the fuel economy meter speedometer change according to the eco drive level. The higher the fuel economy, the brighter the light becomes.

and

Average fuel consumption

The brightness of the arcs

25 MPG or less (9.0 L/100km or more) 26 to 30 MPG (8.8 to 8.0 L/100km) 31 to 35 MPG (7.8 to 7.0 L/100km) 36 MPG or more (6.8 L/100km or less)

Does not illuminate Illuminates weakly Illuminates brightly Illuminates most brightly

140

2-2. Instrument cluster

NOTICE

n To prevent damage to the engine and its components

The gasoline engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place. Check the gasoline engine after it has cooled completely. (→P. 389)

141

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems.

Instrument cluster

Center panel

142

2-2. Instrument cluster

n Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Turn signal indicator (→P. 137)

Headlight high beam indicator (→P. 150)

*1

Slip indicator (→P. 159)

(U.S.A.)

(CANADA) *1

Shift position indicators (→P. 135)

Immobilizer indicator (→P. 83)

(if equipped)

Headlight indicator (→P. 149)

Tail light indicator (→P. 149)

SRS airbag on-off indi- cator (→P. 100)

Cruise control indicator (→P. 155)

Driving ready indicator (→P. 131)

143

2-2. Instrument cluster

n Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 348)

*1, 3

*1, 2

*1

*1, 3

*1, 2

*1

*1

*1, 3

*1, 2

*1, 2

(red indicator) *1

(yellow indicator)

*1: These lights turn on when the “POWER” switch is turned to ON mode to indicate that a system check is being performed. They will turn off after the hybrid system is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer for details.

*2: For vehicles sold in U.S.A. *3: For vehicles sold in Canada

CAUTION

n If a safety system warning light does not come on

Should a safety system light such as the ABS or the SRS warning light not come on when you start the hybrid system, this could mean that these sys- tems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

144

2

2-2. Instrument cluster Multi-information display

The multi-information display presents the driver with a variety of driving-related data, including the outside temperature.

l Outside

temperature dis- (→P. 146) play Indicates the outside tempera- ture.

l Trip information

(→P. 146) Displays driving range, fuel consumption and other cruis- ing-related information.

l Warning messages

(→P. 357) Automatically displayed when a malfunction occurs in one of the vehicle’s systems.

l Odometer and trip meter

display Odometer: Displays the total distance the vehicle has been driven. Trip meter: Displays the dis- tance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances indepen- dently.

145

2-2. Instrument cluster

Switch the display

Display items can be switched by pressing the “DISP” button.

The display will return to the out- side temperature display when the “DISP” button is pressed and held.

l Outside temperature

l Cruising range

Displays the outside air temperature.

The temperature range that can be displayed is from -40°F (-40°C) to 122°F (50°C).

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining.

• This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed. • When only a small amount of fuel is added to the

tank, the display may not be updated.

l Average fuel consumption after refueling

Displays the average fuel consumption since the vehicles was last refueled.

146

2-2. Instrument cluster

l Driving distance

Displays the driving distance since the hybrid sys- tem was started.

l Average vehicle speed

Displays the average vehicle speed since the hybrid system was started.

l Cruise information off

Displays the odometer and trip meters only.

l Zoom display of odometer and trip meter

Displays the odometer and one of the trip meters simultaneously.

l Energy monitor

l Eco drive level

Displays the operating condition of the hybrid sys- tem. (→P. 27)

Displays the eco drive level and the average fuel consumption since the hybrid system was started.

147

2-2. Instrument cluster

NOTICE

n The multi-information display at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed.

148

2

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically.

For U.S.A.

The headlights and parking lights turn on and off automatically. (When the “POWER” switch is in ON mode) The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. Daytime running light system is off.

149

2-3. Operating the lights and wipers

For Canada

The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all lights listed above turn on. The headlights and parking lights turn on and off automatically. (When the “POWER” switch is in ON mode)

Turning on the high beam headlights

With the headlights on, push the lever forward to turn on the high beams. Pull the lever back to the center position to turn the high beams off. Pull the lever toward you to turn on the high beams. Release the lever to turn them off. You can flash the high beams with the headlights on or off.

150

2

2-3. Operating the lights and wipers

n Daytime running light system

To make your vehicle more visible to other drivers, the headlights turn on automatically (at a reduced intensity) whenever the hybrid system is started and the parking brake is released. Daytime running lights are not designed for use at night. For U.S.A.: Daytime running lights can be turned off by operating the switch.

n Headlight control sensor

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. the sensor Doing so detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

n Automatic light off system

l When the headlights are on: The headlights and tail lights turn off 30 sec- onds after all doors are closed with the “POWER” switch OFF. (The lights turn off immediately if the button on the key is pressed after all doors are locked.)

l When only the tail lights are on: The tail lights turn off automatically if the “POWER” switch is turned to ACCESSORY mode or turned OFF and the driver’s door is opened. If any of the doors or trunk lid is left open, the lights automatically turn off after 20 minutes.

To turn the lights on again, turn the “POWER” switch to ON mode, or turn the headlight switch off and then back to the

position.

or

n Customization that can be configured at Toyota dealer

Settings of light sensor sensitivity can be changed. (Customizable features →P. 421)

151

2-3. Operating the lights and wipers

NOTICE

n To prevent the 12-volt battery from being discharged

Do not leave the lights on longer than necessary when the hybrid system is off.

152

2

2-3. Operating the lights and wipers Windshield wipers and washer

Wiper intervals can be adjusted for intermittent operation (when “INT” is selected).

the

Decreases the intermittent windshield wiper frequency Increases intermittent windshield wiper frequency Intermittent windshield wiper operation Low speed windshield wiper operation High wiper operation Temporary operation Wash/wipe operation Wipers operate automatically.

speed windshield

n The windshield wipers and washer can be operated when

The “POWER” switch is in ON mode.

n If no windshield washer fluid sprays

Check that the washer nozzles are not blocked and if there is washer fluid in the windshield washer fluid reservoir.

153

2-3. Operating the lights and wipers

NOTICE

n When the windshield is dry

Do not use the wipers, as they may damage the windshield.

n When there is no washer fluid spray from the nozzle

Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually.

n When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

154

2-4. Using other driving systems Cruise control

Use cruise control to maintain a set speed without using the acceler- ator. n Set the vehicle speed STEP 1

Press the “ON-OFF” button to activate the cruise control.

Press the button once more to deactivate the cruise control.

STEP 2

Accelerate or decelerate to the desired speed and push the lever down to set the cruise control speed.

n Adjusting the speed setting

Increase speed Decrease speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed can be made by lightly pushing the lever up or down and releasing it.

155

2-4. Using other driving systems

n Canceling and resuming regular acceleration

Cancel Pull the lever towards you to cancel cruise control. The speed setting is also can- celed when the brakes are applied. Resume To resume cruise control and return to the set speed, push the lever up.

n Fine adjustment of the set speed

Adjustment of the set speed by approximately 1.0 mph (1.6 km/h) can be made by lightly pressing the lever up or down and releasing it.

n Cruise control can be set when

l The shift lever is in D. l Vehicle speed is between approximately 25 mph and 125 mph (40 km/h

and 200 km/h).

n Accelerating

The vehicle can be accelerated normally. n Automatic cruise control cancellation

The set speed is automatically canceled in any of the following situations. l Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

l Actual vehicle speed is below 25 mph (40 km/h). l VSC is activated.

156

2

2-4. Using other driving systems

n If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Contact your Toyota dealer and have your Toyota inspected.

CAUTION

n To avoid operating the cruise control by mistake

Keep the “ON-OFF” button off when not in use.

n Situations unsuitable for cruise control

In heavy traffic

Do not use cruise control in any of the following situations. Doing so may result in control of the vehicle being lost and could cause seri- ous or fatal accident. l On roads with sharp bends l On winding roads l On slippery roads, such as those covered with rain, ice or snow l On steep hills

157

2-4. Using other driving systems Driving assist systems

To help enhance driving safety and performance, the following sys- tems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle. n ABS (Anti-lock Brake System)

Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface

n Brake assist

Generates an increased level of braking force after the brake pedal is depressed, when the system detects a panic stop situation.

n VSC (Vehicle Stability Control)

Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

n TRAC (Traction Control)

Maintains drive power and prevents the front wheels from spinning when starting the vehicle or accelerating on slippery roads.

n EPS (Electric Power Steering)

Employs an electric motor to reduce the amount of effort needed to turn the steering wheel.

n VDIM (Vehicle Dynamics Integrated Management)

Provides integrated control of the ABS, VSC, TRAC and EPS systems. Maintains vehicle stability when swerving on slippery road surfaces by controlling the brakes, hybrid system output, and steering assist.

158

When VSC and TRAC are operating

2-4. Using other driving systems

If the vehicle is in danger of slip- ping or the front wheels spin, the indicator flashes to indicate that VSC/TRAC have been engaged. A buzzer (intermittent) sounds to indicate that VSC is operating.

n Sounds and vibrations caused by ABS, brake assist, VSC and TRAC l A sound may be heard from the engine compartment when the hybrid system is started or just after the vehicle begins to move. This sound does not indicate that a malfunction has occurred in any of these sys- tems.

l Any of the following conditions may occur when the above systems are

operating. None of these indicates that a malfunction has occurred. • Vibrations may be felt through the vehicle body and steering. • A motor sound may be heard after the vehicle comes to a stop.

n Reduced effectiveness of EPS

The effectiveness of EPS is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result. Should this occur, refrain from excessive steering input or stop the vehicle and turn the hybrid system off. The system should return to normal within 10 minutes.

159

2-4. Using other driving systems

CAUTION

n ABS does not operate effectively when

l Tires with inadequate gripping ability are used (such as excessively worn

tires on a snow covered road).

l The vehicle hydroplanes while driving at high speed on the wet or slick

road.

n Stopping distance when ABS is operating on the wet or slick roads

ABS is not designed to shorten the vehicle's stopping distance. Always maintain a safe distance from the vehicle in front of you in the following situ- ations. l When driving on dirt, gravel or snow-covered roads l When driving with tire chains l When driving over bumps in the road l When driving over roads with potholes or uneven roads

n TRAC may not operate effectively when

Directional control and power may not be achievable while driving on slip- pery road surfaces, even if the TRAC system is operating. Do not drive the vehicle in conditions where stability and power may be lost.

160

2

2-4. Using other driving systems

CAUTION

n When VSC is activated

The slip indicator light flashes and a warning buzzer sounds. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes and a buzzer sounds.

n Replacing tires

Make sure that all tires are of the same size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recom- mended tire pressure level. The ABS and VSC system will not function correctly if different tires are fitted on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.

n Handling of tires and suspension

Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause the system to malfunction.

161

2-5. Driving information Cargo and luggage

Take notice of the following information about storage precau- tions, cargo capacity and load. l Stow cargo and luggage in the trunk whenever possible. l Be sure all items are secured in place. l Be careful to keep the vehicle level. Placing the weight as far for-

ward as possible helps maintain vehicle balance.

l For better fuel economy, do not carry unnecessary weight.

Capacity and distribution

Cargo capacity depends on the total weight of the occupants. (Cargo capacity) = (Total load capacity) - (Total weight of occupants) Steps for Determining Correct Load Limit ⎯ (1) Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehi- cle’s placard.

(2) Determine the combined weight of the driver and passengers

that will be riding in your vehicle.

(3) Subtract the combined weight of the driver and passengers from

XXX kg or XXX lbs.

(4) The resulting figure equals the available amount of cargo and

luggage load capacity. For example, if the XXX amount equals 1400 lbs. and there will be five 150 lb passengers in your vehicle, the amount of avail- able cargo and luggage load capacity is 650 lbs. (1400 - 750
(150 × 5) = 650 lbs.)

(5) Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in Step 4.

162

2

2-5. Driving information

(6)

If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle. Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing.

Example on your vehicle

Cargo capacity Total load capacity

When 2 people with the combined weight of 366 lb. (166 kg) are riding in your vehicle, which has a total load capacity of 900 lb. (410
kg), the available amount of cargo and luggage load capacity will be as follows: 900 lb. - 366 lb. = 534 lb. (410 kg -166 kg = 244 kg)

In this condition, if 3 more passengers with the combined weight of 388 lb. (176 kg) get on, the available cargo and luggage load will be reduced as follows:

534 lb. - 388 lb. = 146 lb. (244 kg - 176 kg = 68 kg) As shown in the above example, if the number of occupants increases, the cargo and luggage load will be reduced by an amount that equals the increased weight due to the additional occupants. In other words, if an increase in the number of occupants causes an excess of the total load capacity (combined weight of occupants plus cargo and luggage load), you must reduce the cargo and luggage on your vehicle.

163

2-5. Driving information

CAUTION

n Storage precautions

l To prevent cargo and luggage from sliding forward during braking, do not stack anything in the enlarged trunk. Keep cargo and luggage low, as close to the floor as possible.

l Never allow anyone to ride in the enlarged trunk. It is not designed for passengers. They should ride in their seats with their seat belts prop- erly fastened. Otherwise, they are much more likely to suffer death or serious bodily injury, in the event of sudden braking or a collision.

l Do not place anything on the package tray behind the rear seatback. Such items may be thrown about and possibly injure people in the vehicle during sudden braking or in an accident.

l Do not drive with objects on top of the instrument panel.

They may interfere with the driver’s field of view or move during sharp acceleration or turning, thus impairing the driver’s control of the vehi- cle. In an accident they may injure the vehicle occupants.

l Secure all items in the occupant compartment, as they may shift and

injure someone during an accident or sudden braking.

n Capacity and distribution

l Do not exceed the maximum axle weight rating or the total vehicle

weight rating.

l Even if the total load of occupant's weight and the cargo load is less

than the total load capacity, do not apply the load unevenly. Improper loading may cause deterioration of steering or braking con- trol which may cause death or serious injury.

164

2-5. Driving information Vehicle load limits

Vehicle load limits include total load capacity, seating capacity, towing capacity and cargo capacity. n Total load capacity: 900 lb. (410 kg)

Total load capacity means the combined weight of occupants, cargo and luggage.

n Seating capacity: 5 occupants (Front 2, Rear 3)

Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person.

n Towing capacity

Toyota does not recommend towing a trailer with your vehicle.

n Cargo capacity

Cargo capacity may increase or decrease depending on the weight and the number of occupants.

n Total load capacity and seating capacity

These details are also described on the tire and loading information label. (→P. 313)

CAUTION

n Overloading the vehicle

Do not overload the vehicle. It may not only cause damage to the tires, but also degrade steering and braking ability, resulting in an accident.

165

2-5. Driving information Winter driving tips

Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a manner appropri- ate to the prevailing weather conditions. n Pre-winter preparations

l Use fluids that are appropriate to the prevailing outside tem-

peratures. • Engine oil • Engine/power control unit coolant • Washer fluid

l Have a service technician inspect the level and specific grav-

ity of battery electrolyte.

l Have the vehicle fitted with four snow tires or purchase a set

of tire chains for the front tires. Ensure that all tires are the same size and brand, and that chains match the size of the tires. n Before driving the vehicle

Perform the following according to the driving conditions. l Do not try to forcibly open a window or move a wiper that is frozen. Pour warm water over the frozen area to melt the ice. Wipe away the water immediately to prevent it from freezing. l To ensure proper operation of the climate control system fan, remove any snow that has accumulated on the air inlet vents in front of the windshield.

l Remove any ice that has accumulated on the vehicle chassis. l Periodically check for and remove any excess ice or snow that may have accumulated in the wheel well or on the brakes.

166

2-5. Driving information

n When driving the vehicle

Accelerate the vehicle slowly and drive at a reduced speed suit- able to road conditions.

n When parking the vehicle

Park the vehicle and move the shift lever to P without setting the parking brake. The parking brake may freeze up, preventing it from being released.

Selecting tire chains

Use the correct tire chain size when mounting the snow chains. Chain size is regulated for each tire size.

Side chain:

0.12 in. (3 mm) in diameter 0.39 in. (10 mm) in width 1.18 in. (30 mm) in length

Cross chain:

0.16 in. (4 mm) in diameter 0.55 in. (14 mm) in width 0.98 in. (25 mm) in length

Regulations on the use of snow chains

l Regulations regarding the use of tire chains vary according to loca- tion and type of road. Always check local regulations before install- ing chains. Install the chains on the front tires.

l Retighten the chains after driving 1/4 - 1/2 mile (0.5 - 1.0 km).

167

2-5. Driving information

n Tire chains

Observe the following precautions when installing and removing chains.

Install and remove tire chains in a safe location. Install tire chains on the front tires only. Do not install tire chains on rear tires. Install tire chains following the instructions provided in the accompanying manual.

CAUTION

n Driving with snow tires

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in a loss of vehicle control and cause death or serious injury. l Use tires of the size specified for your vehicle. l Maintain the recommended level of air pressure. l Do not drive in excess of 75 mph (120 km/h), regardless of the type of

snow tires being used.

l Use snow tires on all, not just some wheels.

n Driving with tire chains

Observe the following precautions to reduce the risk of accidents. Failing to do so may result in the vehicle being unable to be driven safely, and may cause death or serious injury. l Do not drive in excess of the speed limit specified for the tire chains being

used or 30 mph (50 km/h), whichever is lower.

l Avoid driving on bumpy road surfaces or over potholes. l Avoid sudden turns and braking, as use of chains may adversely affect

vehicle handling.

l Slow down sufficiently before entering a curve to ensure that vehicle con-

trol is maintained.

168

2-5. Driving information

NOTICE

n Repairing or replacing snow tires

Request repairs of and obtain replacement snow tires from Toyota dealers or legitimate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.

n Fitting tire chains

The tire pressure warning valves and transmitters may not function correctly when tire chains are fitted.

169

2-5. Driving information Trailer towing

Toyota does not recommend towing a trailer with your vehicle. Toy- ota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicycle, etc. Your Toyota is not designed for trailer towing or for the use of tow hitch mounted carriers.

170

2-5. Driving information Dinghy towing

Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home.

NOTICE

n To avoid serious damage to your vehicle

Do not tow your vehicle with four wheels on the ground.

171

3-1. Using the air conditioning system and defogger Automatic air conditioning system

Air outlets are automatically selected and fan speed is automatically adjusted according to the temperature setting.

Air outlet display

Fan speed display

Driver’s side temperature setting display Driver’s side temper- ature control

“DUAL” button

Front passenger’s side temperature setting display

Change the air outlets used (air flow selector button)

Front passenger’s side temperature control

Automatic mode

Off

Windshield defogger

Air conditioning on/off switch

Fan speed (fan speed selector)

Outside air or recirculated air mode

n “ECO HEAT/COOL” switch “ECO HEAT/COOL” mode enables the air conditioning to be oper- ated at a reduced capacity in order to limit use of the hybrid battery (traction battery). The effectiveness of the air conditioning will be lower than normal.

On/off

“ECO HEAT/COOL” When mode is turned on, the switch indicator will come on and the “ECO” indicator will appear on the air conditioning display.

174

3-1. Using the air conditioning system and defogger

Using the automatic mode

STEP 1

Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting.

STEP 2

Turning

to the right increases the temperature and

to the left decreases the temperature on the

turning driver’s side. The temperature for the driver and passenger seats can be set sep- arately.

Adjusting the settings

n Adjusting the temperature setting

Turning

to the right increases the temperature and turning

to the left decreases the temperature on the driver’s side.

Turning to the left (decrease) on the passenger’s side to separately adjust the temperature for the pas-

to the right (increase) or

senger’s and driver’s side (dual mode). Press to return the driver's and passenger side temperatures to the same setting (simulta- neous mode). The air conditioning system switches between dual and simultaneous

mode each time

is pressed.

175

3-1. Using the air conditioning system and defogger

n Adjusting the fan speed

Press “∧” (increase) or “∨” (decrease) on the fan speed selector. The fan speed is shown on the display. (7 levels) Press

to turn the fan off.

n Changing the air outlets

Press the air flow selector button. The air outlets switch each time the button is pressed. The air flow shown on the display indicates the following.

Air flows to the upper body.

Air flows to the upper body and feet.

Air flows to the feet.

176

3-1. Using the air conditioning system and defogger

Air flows to the feet and the windshield defogger operates.

Recirculated air mode will auto- matically switch to outside air mode.

n Switching between outside air and recirculated air modes

Press The mode switches between outside air mode (indicator off) and recirculated air mode (indicator on) modes each time the button is pressed.

Defogging the windshield

Defogging

The air conditioning system con- trol operates automatically. Recirculated air mode will auto- matically switch to outside air mode. It is not possible to return to recirculated air mode when the windshield defogger switch is on.

177

3-1. Using the air conditioning system and defogger

Adjusting the position of and opening and closing the air outlets

Center outlets

Direct air flow to the left or right, up or down.

Direct air flow to the left or right, up or down. Turn the knob right to open the vent and left to close the vent.

Direct air flow to the left or right, up or down. Turn the knob up to open the vent and down to close the vent.

Right and left side outlets

Rear outlets

178

3-1. Using the air conditioning system and defogger

Steering wheel switches

Some air conditioning features can be controlled using the switches on the steering wheel.

Temperature selector “DUAL” button indicator on: Indi- vidual setting on the driver's side only. “DUAL” button Simultaneous setting on driver’s and sides. Automatic mode Off

indicator off: the front passenger’s

n Using the automatic mode STEP 1

Press The air conditioning system will begin to operate. Air outlets and fan speed are automatically adjusted according to the temperature setting. (→P. 180) Press “∧” to increase the temperature and “∨” to decrease the temperature on the The temperature for the driver and passenger seat can be set sepa- rately.

switch.

STEP 2

n Adjusting the temperature setting

Press “∧” to increase the temperature and “∨” to decrease the tem- perature on the

switch.

n Turning off the air conditioning system

Press

179

3-1. Using the air conditioning system and defogger

n Using the automatic mode

Fan speed is adjusted automatically in accordance with the temperature set- ting and ambient conditions. As a result, the following may occur. l The system may switch automatically to recirculated air mode when the

coolest temperature setting is selected in summer.

Immediately after warm or cool air is ready to flow.

is pressed, the fan may stop for a while until

l Cool air may flow to the area around the upper body when the heater is

on.

n Using the system in recirculated air mode

The windows will fog up more easily if the recirculated air mode is used for an extended period.

n When the “ECO HEAT/COOL” mode is canceled

l The temperature control is set at “LO” (the lowest temperature) or “HI”

(the highest temperature).

l The air flow is set in the floor/windshield mode or windshield mode. l The “ECO HEAT/COOL” switch is pushed again.

n Window defogger feature

Recirculated air mode may automatically switch to outside air mode in situa- tions where the windows need to be defogged.

n When outside air temperature approaches 32°F (0°C) The air conditioning system may not operate even when

n When the indicator light on

flashes

is pressed.

and turn off the air conditioning system before turning it on Press once more. There may be a problem in the air conditioning system if the indi- cator light continues to flash. Turn the air conditioning system off and have it inspected by your Toyota dealer.

n Windshield air flow button

When the “POWER” switch is set at ON mode after the 12-volt battery is reconnected, the indicator light on the button may flash and a motor sound may be heard. This does not indicate a malfunction.

180

3-1. Using the air conditioning system and defogger

n Plasmacluster™*

This air conditioning system adopts plasmacluster technology, which helps to keep good air quality in the cabin by emitting positive and negative ions through the driver's side vent. A slight noise may be heard during operation. This is not a malfunction. Also, static electricity may be discharged near the driver's side vent due to the high voltage used to operate the system. To clean the drive's side vent, turn the system off and wipe the vent using a soft cloth. *Plasmacluster technology is manufactured under license from the SHARP Corporation. “Plasmacluster™” is a trademark of the SHARP Corporation.

CAUTION

n To prevent the windshield from fogging up

during cool air operation in extremely humid weather. Do not use The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, blocking your vision.

n Plasmacluster™

Do not disassemble or repair the system because it contains high voltage parts. Call your Toyota dealer if the system needs repair.

NOTICE

n To prevent the 12-volt battery from being discharged

Do not leave the air conditioning system on longer than necessary when the hybrid system is off.

n To prevent damage to the Plasmacluster™

Do not insert anything into the driver's side vent, attach anything to it, or use sprays around the drive's side vent. These things may cause the system not to work properly.

181

3-1. Using the air conditioning system and defogger Rear window and outside rear view mirror defoggers

Clear the rear window using the defogger.

On/off

turn off

The defoggers will automati- cally the operation time. The operation time is between 15 minutes and 1
hour depending on the ambient temperature vehicle speed.

and

n Outside rear view mirror defoggers (if equipped)

Turning the rear window defogger on will turn the outside rear view mirror defoggers on.

CAUTION

n Outside rear view mirror defoggers (if equipped)

The surfaces of the outside rear view mirrors become hot. Do not touch them to prevent from burning yourself.

182

3-2. Using the audio system Audio system types

Owners of models equipped with a navigation system should refer to the “Navigation System Owner's Manual”.

CD player and AM/FM radio

CD player with changer and AM/FM radio

183

3-2. Using the audio system

Title

Using the radio Using the CD player Playing MP3 and WMA discs Optimal use of the audio system Using the AUX adapter Using the steering wheel audio switches

Page P. 186
P. 192
P. 199
P. 207
P. 210
P. 211

n Using cellular phones

Interference may be heard through the audio system's speakers if a cellular phone is being used inside or close to the vehicle while the audio system is operating.

CAUTION

n For vehicles sold in U.S.A. and Canada

l Part 15 of the FCC Rules

FCC Warning: Any unauthorized changes or modifications to this equipment will void the user’s authority to operate this device.

l Laser products

• Do not take this unit apart or attempt to make any changes yourself.

This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs. The laser is carefully shielded so that its rays remain inside the cabinet. Therefore, never try to disas- semble the player or alter any of its parts since you may be exposed to laser rays and dangerous voltages.

• This product utilizes a laser.

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation expo- sure.

184

3-2. Using the audio system

NOTICE

n To prevent the 12-volt battery from being discharged

Do not leave the audio system on longer than necessary with the hybrid sys- tem off.

n To avoid damaging the audio system

Take care not to spill drinks or other fluids over the audio system.

185

3-2. Using the audio system Using the radio

Power

Volume

the

Adjusting frequency (AM, FM mode) or channel (SAT mode)

Scanning for receivable stations (“SCAN” button) Seeking the frequency Changing the channel