2009 Toyota Camry HV Owners Manual

Connecting the jumper cables

If required, remove all vent plugs from the booster battery. Lay a cloth over the open vents on the booster battery. (This helps reduce the explosion hazard, personal injuries and burns.) Positive (+) battery terminal on your vehicle Positive (+) battery terminal on the second vehicle Negative (-) battery terminal on the second vehicle Connect the jumper cable to ground on your vehicle as shown in the illustration.

385

5-2. Steps to take in an emergency

STEP 3

STEP 4

STEP 5

STEP 6

Start the engine of the second vehicle. Increase the gaso- line engine speed slightly and maintain at that level for approximately 5 minutes to recharge the 12-volt battery of your vehicle. Open and close any of the doors with the “POWER” switch OFF. Maintain the engine speed of the second vehicle and turn the “POWER” switch to ON mode, then start the hybrid sys- tem. Make sure the “READY” indicator comes on. If the indicator does not comes on, contact your Toyota dealer. Once the hybrid system has started, remove the jumper cables in the exact reverse order in which they were con- nected.

Once the hybrid system starts, have the vehicle checked at your Toyota dealer as soon as possible.

n Avoiding a discharged 12-volt battery

l Turn off the headlights and the audio system while the hybrid system is

turned off.

l Turn off any unnecessary electrical components when the vehicle is run- ning at a low speed for an extended period, such as in heavy traffic, etc.

n When the 12-volt battery is removed or discharged

l The hybrid system may not start. (→P. 301) l The tire pressure warning system must be initialized. (→P. 305)

n Starting the hybrid system when the 12-volt battery is discharged

The hybrid system cannot be started by push-starting.

386

5-2. Steps to take in an emergency

CAUTION

n Avoiding 12-volt battery fires or explosions

Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the 12-volt battery. l Make sure each jumper cable is connected to the correct terminal. l Do not allow the ends of the jumper cable used for the “+” terminals to come into contact with any other parts or metal surface in the area, such as brackets or unpainted metal.

l Do not allow the “+” and “-” terminals of the jumper cables to come into

contact with each other.

l Do not smoke, use matches, cigarette lighters or allow open flame near

the 12-volt battery.

n 12-volt battery precautions

The 12-volt battery contains poisonous and corrosive acidic electrolyte, while related parts contain lead and lead compounds. Observe the following precautions when handling the 12-volt battery. l When working with the 12-volt battery, always wear safety glasses and take care not to allow any battery fluids (acid) to come into contact with skin, clothing or the vehicle body.

l Do not lean over the 12-volt battery.

In the event that battery fluid comes into contact with the skin or eyes, immediately wash the affected area with water and seek medical attention. Place a wet sponge or cloth over the affected area until medical attention can be received.

l Always wash your hands after handling the 12-volt battery support, termi-

nals, and other battery-related parts.

l Do not allow children near the 12-volt battery.

387

5-2. Steps to take in an emergency

NOTICE

n When handling jumper cables

Be careful that the jumper cables do not become tangled in the cooling fans or any of the belts when connecting or disconnecting them.

388

5-2. Steps to take in an emergency If your vehicle overheats

The following may indicate that your vehicle is overheating:

“WATER TEMP” is shown on the multi-information display: The engine may be overheating. “HYBRID SYSTEM OVER HEAT” is shown on the multi-informa- tion display: The power control unit may be overheating.

Follow the correction procedure as described below.

Correction procedures

n If “WATER TEMP” is shown on the multi-information display STEP 1

Stop the vehicle in a safe place and turn off the air condition- ing system. Check to see if steam is coming out from under the hood. If you see steam:

STEP 2

Stop the hybrid system. Carefully lift the hood after the steam subsides and then restart the hybrid system.

If you do not see steam:

Leave the hybrid system operating and carefully lift the hood.

STEP 3

Check to see if the cooling fan is operating. If the fans are operating:

Wait until the temperature of the engine (shown on the instrument cluster) begins to fall and then stop the hybrid system.

If the fans are not operating:

Stop the hybrid system immediately and call your Toyota dealer.

389

5-2. Steps to take in an emergency

STEP 4

STEP 5

After the hybrid system has cooled down sufficiently, check the engine coolant level and inspect the radiator core (radia- tor) for any leaks.

Add engine coolant if necessary. Water can be used in an emer- gency if engine coolant is unavail- able. (→P. 401)

n If “HYBRID SYSTEM OVER HEAT” is shown on the multi-infor-

mation display

STEP 1

STEP 2

STEP 3

Stop the vehicle in a safe place and turn off the air condition- ing system. Leave the hybrid system operating and carefully lift the hood. Check if the cooling fans are operating. If the fans are operating:

Wait until “HYBRID SYSTEM OVER HEAT” disappears and then stop the hybrid system. If the message does not disappear, call your Toyota dealer.

If the fans are not operating:

Stop the hybrid system immediately and call your local Toyota dealer.

390

STEP 4

STEP 5

5-2. Steps to take in an emergency

After the hybrid system has cooled down, check the power control unit coolant level and inspect the cooling system for leaks.

Add power control unit coolant if necessary.

Water can be used in an emer- gency if power control unit cool- ant is unavailable. (→P. 401)

Have the vehicle checked at the nearest Toyota dealer as soon as possible.

n Overheating

The following symptoms may occur when your vehicle is overheating: l Hybrid system output decreases. l Steam is coming from the engine area.

391

5-2. Steps to take in an emergency

CAUTION

n To prevent an accident or injury when inspecting under the hood of

your vehicle

If steam is seen coming from under the hood, do not open the hood until the steam has subsided. The engine compartment may be very hot, caus- ing serious injury such as burns.

l With a hybrid vehicle, there are times when the gasoline engine automati- cally starts to run or the cooling fans suddenly start to operate. Do not touch or approach the rotating parts of the belt or fans. Doing so may lead to fingers, clothes or tools getting caught, resulting in an accidental injury. l Do not loosen the coolant reservoir cap while the hybrid system and radia-

tor are hot. Serious injury, such as burns, may result from hot coolant and steam released under pressure.

NOTICE

n When adding engine/power control unit coolant

Wait until the hybrid system has cooled down before adding engine/power control unit coolant. When adding coolant, do so slowly. Adding cool coolant to a hot hybrid sys- tem too quickly can cause damage to the hybrid system.

392

5-2. Steps to take in an emergency If the vehicle becomes stuck

Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt, or snow. STEP 1

Stop the hybrid system. Set the parking brake and put the shift lever in P. Remove the mud, snow, or sand from around the stuck tire. Place wood, stones or some other material to help provide traction under the tires. Restart the hybrid system. Shift the shift lever to the D or R position and carefully apply the accelerator to free the vehicle.

STEP 2

STEP 3

STEP 4

STEP 5

n Emergency hooks (if equipped)

When your vehicle becomes stuck and cannot move, the emergency hooks are used for another vehicle to pull your vehi- cle out in an emergency. Your vehicle is not designed to tow another vehicle.

CAUTION

n When attempting to free a stuck vehicle

If you choose to rock the vehicle back and forth to free it, make sure the sur- rounding area is clear, to avoid striking other vehicles, objects or persons. The vehicle may also lunge forward or lunge back suddenly as it becomes free. Use extreme caution.

n When shifting the shift lever

Be careful not to shift the shift lever with the accelerator pedal depressed. This may lead to unexpected rapid acceleration of the vehicle that may cause an accident and result in death or serious injury.

393

5-2. Steps to take in an emergency

NOTICE

n To avoid damaging the transmission and other components

l Avoid spinning the wheels.

If the vehicle remains stuck after trying these procedures, the vehicle may require towing to be freed.

394

6-1. Specifications Maintenance data (fuel, oil level, etc.)

Dimensions and weights

Overall length Overall width Overall height* Wheelbase

Tread

Front Rear

Vehicle capacity weight (Occupants + luggage) *: Unladen vehicles

Vehicle identification

189.2 in. (4805 mm) 71.7 in. (1820 mm) 57.9 in. (1470 mm) 109.3 in. (2775 mm) 62.0 in. (1575 mm) 61.6 in. (1565 mm)

900 lb. (410 kg)

n Vehicle identification number The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle.

This number is stamped on the top left of the instrument panel.

396

6-1. Specifications

This number is also on the Certi- fication label on the driver’s side center pillar.

n Gasoline engine number and electric motor (traction motor)

number

The gasoline engine number and electric motor (traction motor) num- ber are stamped as shown.

Gasoline engine number Electric motor (traction motor) number

397

6-1. Specifications

Engine

Model Type Bore and stroke Displacement Drive belt tension Valve clearance (engine cold) Intake Exhaust

Fuel

2AZ-FXE engine 4 cylinder in-line, 4 cycle, gasoline 3.48 × 3.78 in. (88.5 × 96.0 mm) 144.1 cu.in. (2362 cm3) Automatic adjustment

0.007 ⎯ 0.011 in. (0.19 ⎯ 0.29 mm) 0.015 ⎯ 0.019 in. (0.38 ⎯ 0.48 mm)

Fuel type Octane rating Fuel tank capacity

Unleaded gasoline only 87 (Research Octane Number 91) or higher 17.2 gal. (65 L, 14.3 lmp.gal.)

Electric motor (traction motor)

Type Maximum output Maximum torque

Permanent magnet synchronous motor 105 kW 199 ft•lbf (270 N•m, 27.5 kgf•m)

398

6-1. Specifications

Hybrid battery (traction battery)

Type Voltage Capacity Quantity Overall voltage

Nickel-Metal hydride battery 7.2 V/module 6.5 Ah (3HR) 34 modules 244.8 V

399

6-1. Specifications

Lubrication system

Oil capacity (drain and refill)

With filter Without filter

Oil grade

Recommended oil viscosity

4.5 qt. (4.3 L, 3.8 Imp.qt.) 4.3 qt. (4.1 L, 3.6 Imp.qt.) ILSAC multi-grade engine oil Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to satisfy the grade and vis- cosity shown below.

Outside temperature

*: 0W-20 is the oil that provides the optimal level of fuel efficiency. Oil viscosity l The 0W portion of the oil viscosity rating indicates the characteristic of the oil which allows cold startability. Oils with a lower value before the W allow for easier starting of the engine in cold weather.

l The 20 in 0W-20 indicates the oil viscosity when the oil is at its oper- ating temperature. An oil with a higher viscosity may be better suited if the vehicle is operated at high speeds, or under extreme load con- ditions.

400

6-1. Specifications

6.6 qt. (6.2 L, 5.5 Imp.qt.) 3.1 qt. (2.9 L, 2.6 Imp.qt.)

Use either of the following. • “Toyota Super Long Life Coolant” • Similar high-quality ethylene glycol-based non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology

Do not use plain water alone.

DENSO SK20R11
NGK IFR6A11

Cooling system

Gasoline engine Power control unit

Coolant type

Ignition system

Spark plug Make

Gap

0.043 in. (1.1 mm)

NOTICE

n Iridium-tipped spark plugs

Use only iridium-tipped spark plugs. Do not adjust spark plug gap.

401

6-1. Specifications

Electrical system

12-volt battery

Open voltage at 68°F (20°C):

Charging rates

Transaxle

12.6 ⎯ 12.8 V Fully charged 12.2 ⎯ 12.4 V Half charged 11.8 ⎯ 12.0 V Discharged (Voltage checked 20 minutes after the hybrid system and all the lights are turned off) 5 A max.

Fluid capacity (drain and refill) Fluid type *: The fluid capacity is the quantity of reference. If replacement is nec-

4.3 qt. (4.1 L, 3.7 Imp.qt.)*

Toyota Genuine ATF WS

essary, contact your Toyota dealer.

NOTICE

n Transmission fluid type

Using transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of your transmission accompanied by vibration, and ultimately damage the transmission of your vehicle.

402

6-1. Specifications

Brakes

Pedal clearance *1
Pedal free play Brake pad wear limit Parking brake pedal travel *2
Fluid type *1: Minimum pedal clearance when depressed with a force of 110 lbf (490 N,

3.1 in. (80 mm) 0.04 ⎯ 0.08 in. (1 ⎯ 2 mm) 0.04 in. (1.0 mm) 7 ⎯ 10 clicks SAE J1703 or FMVSS No.116 DOT 3

50 kgf) while the hybrid system is running

*2: Parking brake pedal travel when depressed with a force of 67 lbf (300 N, 31

kgf).

Steering

Free play

Less than 1.2 in. (30 mm)

403

6-1. Specifications

Tires and wheels

Tire size

Tire inflation pressure (Recommended cold tire inflation pressure)

P215/60R16 94V, T155/70D17 110M Driving under normal conditions Front: 32 psi (220 kPa, 2.2 kgf/cm2 or bar)* Rear: 32 psi (220 kPa, 2.2 kgf/cm2 or bar)* Spare: 60 psi (420 kPa, 4.2 kgf/cm2 or bar) *: When driving at high speeds above

100 mph (160 km/h), in countries where such speeds are permitted by law, add 3 psi (20 kPa, 0.2 kgf/cm2 or bar) to the front tires and rear tires. Never exceed the maximum cold tire inflation pressure indicated on the tire sidewall.

Wheel size Wheel nut torque

16 × 6 1/2 J, 17 × 4 T (compact spare) 76 ft•lbf (103 N•m, 10.5 kgf•m)

404

6-1. Specifications

Light bulbs

Light Bulbs

Bulb No.

Exterior

Interior

Headlights Low beam High beam Front side marker lights Front turn signal/park- ing lights Rear turn signal lights License plate lights Back-up lights Personal lights Interior light Door courtesy lights Vanity lights Glove box light Trunk light

55
60

⎯ 9005

⎯

3457NAK

27/8

⎯

⎯ 921
⎯

21
16
1.2
3.8
B: HB3 halogen bulbs D: Wedge base bulbs (amber)

⎯ 168
⎯

⎯

⎯

A: H11 halogen bulbs C: Wedge base bulbs (clear) E: Double end bulbs

Type

405

6-1. Specifications Fuel information

You must only use unleaded gasoline in your vehicle. Unleaded gasoline with an Octane Rating of 87 (Research Octane Number 91) or higher is required for optimum engine performance. At minimum, the gasoline you use should meet the specifications of ASTM D4814 in the U.S.A. and CGSB3.5-M93 in Canada.

n Fuel tank opening for unleaded gasoline

To help prevent incorrect fueling, your Toyota has a fuel tank opening that only accommodates the special nozzle on unleaded fuel pumps.

n If your engine knocks

l Consult your Toyota dealer. l You may occasionally notice light knocking for a short time while acceler-

ating or driving uphill. This is normal and there is no need for concern.

n Gasoline quality

In very few cases, driveability problems may be caused by the brand of gas- oline you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer.

n Gasoline quality standards

l Automotive manufacturers in the U.S., Europe and Japan have devel- oped a specification for fuel quality called the World-Wide Fuel Charter (WWFC) that is expected to be applied worldwide.

l The WWFC consists of four categories that are based on required emis-

sion levels. In the U.S., category 4 has been adopted.

l The WWFC improves air quality by lowering emissions in vehicle fleets,

and improves customer satisfaction through better performance.

406

6-1. Specifications

n Toyota recommends the use of gasoline containing detergent additives l Toyota recommends the use of gasoline that contains detergent additives

to avoid build-up of engine deposits.

l All gasoline sold in the U.S. contains detergent additives to clean and/or

keep clean intake systems.

n Toyota recommends the use of cleaner burning gasoline

Cleaner burning gasoline, including reformulated gasoline that contains oxy- genates such as ethanol or MTBE (Methyl Tertiary Butyl Ether) is available in many areas. Toyota recommends the use of cleaner burning gasoline and appropriately blended reformulated gasoline. These types of gasoline provide excellent vehicle performance, reduce vehicle emissions and improve air quality.

n Toyota does not recommend blended gasoline

l Toyota allows the use of oxygenate blended gasoline where the oxygen-

ate content is up to 10% ethanol or 15% MTBE. If you use gasohol in your Toyota, be sure that it has an octane rating no lower than 87.

l Toyota does not recommend the use of gasoline containing methanol.

n Toyota does not recommend gasoline containing MMT

Some gasoline contains octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected. The malfunction indicator lamp on the instrument cluster may come on. If this happens, contact your Toyota dealer for service.

407

6-1. Specifications

NOTICE

n Notice on gasoline quality

l Do not use leaded gasoline.

Leaded gasoline can cause damage to your vehicle’s catalytic converters causing the emission control system to malfunction.

l Do not use gasohol other than that stated here.

Other gasohol may cause fuel system damage or vehicle performance problems.

n Fuel-related poor driveability

If after using a different type of fuel, poor driveability is encountered (poor hot starting, vaporization, engine knocking, etc.), discontinue the use of that type of fuel.

n When refueling with gasohol

Take care not to spill gasohol. It can damage your vehicle's paint.

408

6-1. Specifications Tire information

Typical tire symbols (standard tire)

Typical tire symbols (compact spare tire)

Tire size DOT and Tire Identification Number (TIN) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators

(→P. 412) (→P. 411)

(→P. 304)

409

6-1. Specifications

Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire. Radial tires or bias-ply tires A radial tire has “RADIAL” on the sidewall. A tire not marked “RADIAL” is a bias-ply tire. “TUBELESS” or “TUBE TYPE” A tubeless tire does not have a tube and air is directly filled in the tire. A tube type tire has a tube inside the tire and the tube main- tains the air pressure. Load limit at maximum cold tire inflation pressure Maximum cold tire inflation pressure This means the pressure to which a tire may be inflated. Summer tires or all season tires (→P. 309) An all season tire has “M+S” on the sidewall. A tire not marked “M+S” is a summer tire. “TEMPORARY USE ONLY” (→P. 373) A compact spare tire is identified by the phrase “TEMPORARY USE ONLY” molded into its sidewall. This tire is designed for temporary emergency use only.

(→P. 308) (→P. 404)

410

6-1. Specifications

Typical DOT and Tire Identification Number (TIN)

Identification Number

DOT symbol* Tire (TIN) Tire manufacturer's identifica- tion mark Tire size code Manufacturer's optional type code (3 or 4 letters) Manufacturing week Manufacturing year *: The DOT symbol certifies that to applicable Federal Motor Vehicle Safety Standards.

tire conforms

the

tire

411

The illustration indicates typical tire size.

Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 or 3 digits) Speed symbol (alphabet with one letter)

Section width Tire height Wheel diameter

6-1. Specifications

Tire size

n Typical tire size information

n Tire dimensions

412

6-1. Specifications

Tire section names

Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer

Uniform Tire Quality Grading

This information has been prepared in accordance with regulations issued by the National Highway Traffic Safety Administration of the U.S.A. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading.

Your Toyota dealer will help answer any questions you may have as you read this information.

n DOT quality grades

All passenger vehicle tires must conform to Federal Safety Requirements in addition to these grades. Quality grades can be found where applicable on the tire sidewall between tread shoulder and maximum section width. For example: Treadwear 200 Traction AA Temperature A

413

6-1. Specifications

n Treadwear

The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a speci- fied government test course. For example, a tire graded 150 would wear one and a half (1-1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however, and may depart significantly from the norm due to variations in driving habits, service practices and differences in road characteristics and climate.

n Traction AA, A, B, C

The traction grades, from highest to lowest, are AA, A, B and C, and they represent the tire's ability to stop on wet pavement as measured under controlled conditions on specified government test surfaces of asphalt and concrete. A tire marked C may have poor traction performance. Warning: The traction grade assigned to this tire is based on braking (straight ahead) traction tests and does not include cornering (turn- ing) traction.

n Temperature A, B, C

The temperature grades are A (the highest), B, and C, represent- ing the tire's resistance to the generation of heat and its ability to dissipate heat when tested under controlled conditions on a speci- fied indoor laboratory test wheel. Sustained high temperature can cause the material of the tire to degenerate and reduce tire life, and excessive temperature can lead to sudden tire failure. The grade C corresponds to a level of performance which all passen- ger car tires must meet under the Federal Motor Vehicle Safety Stan- dard No. 109. Grades B and A represent higher levels of performance on the labo- ratory test wheel than the minimum required by law.

414

6-1. Specifications

Warning: The temperature grades for this tire are established for a tire that is properly inflated and not overloaded. Excessive speed, underinflation, or excessive loading, either sepa- rately or in combination, can cause heat buildup and possible tire fail- ure.

Glossary of tire terminology

Tire related term

Meaning

Cold tire inflation pres- sure

Maximum inflation pressure

Recommended infla- tion pressure

Accessory weight

Curb weight

Maximum loaded vehi- cle weight

Tire pressure when the vehicle has been parked for three hours or more, or has not been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which a tire may be inflated, shown on the sidewall of the tire Cold tire inflation pressure recommended by a manufacturer The combined weight (in excess of those stan- dard items which may be replaced) of auto- matic transmission, power steering, power brakes, power windows, power seats, radio and heater, to the extent that these items are available as factory-installed equipment (whether installed or not) The weight of a motor vehicle with standard equipment, including the maximum capacity of fuel, oil and coolant, and if so equipped, air conditioning and additional weight optional engine The sum of: (a) Curb weight (b) Accessory weight (c) Vehicle capacity weight (d) Production options weight

415

6-1. Specifications

Tire related term

Normal occupant weight

Occupant distribution

Production options weight

Rim

Rim diameter (Wheel diameter) Rim size designation

Rim type designation

Rim width Vehicle capacity weight (Total load capacity)

Vehicle maximum load on the tire

Vehicle normal load on the tire

416

Meaning

150 lb. (68 kg) times the number of occupants specified in the second column of Table 1* that follows Distribution of occupants in a vehicle as speci- fied in the third column of Table 1* below The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they replace, not previously considered in curb weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube assembly upon which the tire beads are seated

Nominal diameter of the bead seat

Rim diameter and width The industry manufacturer's designation for a rim by style or code Nominal distance between rim flanges The rated cargo and luggage load plus 150 lb. (68 kg) times the vehicle's designated seating capacity The load on an individual tire that is determined by distributing to each axle its share of the maximum loaded vehicle weight, and dividing by two The load on an individual tire that is determined by distributing to each axle its share of curb weight, accessory weight, and normal occu- pant weight (distributed in accordance with Table 1* below), and dividing by two

Tire related term

Weather side

Bead

Bead separation

Bias ply tire

Carcass

Chunking

Cord

Cord separation

Cracking

CT

Extra load tire

Groove

Innerliner

6-1. Specifications

Meaning

The surface area of the rim not covered by the inflated tire The part of the tire that is made of steel wires, wrapped or reinforced by ply cords and that is shaped to fit the rim A breakdown of the bond between components in the bead A pneumatic tire in which the ply cords that extend to the beads are laid at alternate angles substantially less than 90 degrees to the cen- terline of the tread The tire structure, except tread and sidewall rubber which, when inflated, bears the load The breaking away of pieces of the tread or sidewall The strands forming the plies in the tire The parting of cords from adjacent rubber com- pounds Any parting within the tread, sidewall, or inner- liner of the tire extending to cord material A pneumatic tire with an inverted flange tire and rim system in which the rim is designed with rim flanges pointed radially inward and the tire is designed to fit on the underside of the rim in a manner that encloses the rim flanges inside the air cavity of the tire A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire The space between two adjacent tread ribs The layer(s) forming the inside surface of a tubeless tire that contains the inflating medium within the tire

417

6-1. Specifications

Tire related term

Innerliner separation

Intended outboard sidewall

Light truck (LT) tire

Load rating

Maximum load rating

Maximum permissible inflation pressure

Measuring rim

Open splice

Outer diameter

Overall width

Passenger car tire

418

Meaning

The parting of the innerliner from cord material in the carcass (a) The sidewall that contains a whitewall, bears white lettering, or bears manufac- turer, brand, and/or model name molding that is higher or deeper than the same molding on the other sidewall of the tire, or

(b) The outward facing sidewall of an asym-

metrical tire that has a particular side that must always face outward when mounted on a vehicle

A tire designated by its manufacturer as prima- rily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry for a given inflation pressure The load rating for a tire at the maximum per- missible inflation pressure for that tire The maximum cold inflation pressure to which a tire may be inflated The rim on which a tire is fitted for physical dimension requirements Any parting at any junction of tread, sidewall, or innerliner that extends to cord material The overall diameter of an inflated new tire The linear distance between the exteriors of the sidewalls of an inflated tire, including eleva- tions due to labeling, decorations, or protective bands or ribs A tire intended for use on passenger cars, mul- tipurpose passenger vehicles, and trucks, that have a gross vehicle weight rating (GVWR) of 10,000 lb. or less.

Tire related term

Ply

Ply separation

Pneumatic tire

Radial ply tire

Reinforced tire

Section width

Sidewall

Sidewall separation

Snow tire

Test rim

6-1. Specifications

Meaning

A layer of rubber-coated parallel cords A parting of rubber compound between adja- cent plies A mechanical device made of rubber, chemi- cals, fabric and steel or other materials, that, when mounted on an automotive wheel, pro- vides the traction and contains the gas or fluid that sustains the load A pneumatic tire in which the ply cords that extend to the beads are laid at substantially 90 degrees to the centerline of the tread A tire designed to operate at higher loads and at higher inflation pressures than the corre- sponding standard tire The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and bead The parting of the rubber compound from the cord material in the sidewall A tire that attains a traction index equal to or greater than 110, compared to the ASTM-E 1136 Standard Reference Test Tire, when using the snow traction test as described in ASTM F-1805-00, Standard Test Method for Signal Wheel Driving Traction in a Straight Line on Snow-and Ice-Covered Surfaces, and which is marked with an Alpine Symbol ( ) on at least one sidewall The rim on which a tire is fitted for testing, and may be any rim listed as appropriate for use with that tire

419

6-1. Specifications

Tire related term

Meaning

Tread

Tread rib

Tread separation

Treadwear indicators (TWI)

That portion of a tire that comes into contact with the road A tread section running circumferentially around a tire Pulling away of the tread from the tire carcass The projections within the principal grooves designed to give a visual indication of the degrees of wear of the tread The fixture used to hold the wheel and tire assembly securely during testing

Wheel-holding fixture *: Table 1 ⎯ Occupant loading and distribution for vehicle normal load

for various designated seating capacities

Designated seating capacity, Number of

occupants 2 through 4

5 through 10

11 through 15

16 through 20

Vehicle normal load, Number of occupants

Occupant distribution in a normally loaded vehi-

cle

2 in front

2 in front, 1 in second

seat

2 in front, 1 in second seat, 1 in third seat, 1

in fourth seat

2 in front, 2 in second seat, 2 in third seat, 1

in fourth seat

420

6-2. Customization Customizable features

Your vehicle includes a variety of electronic features that can be per- sonalized to your preferences. Programming these preferences requires specialized equipment and may be performed by your Toy- ota dealer. Some function settings are changed simultaneously with other functions being customized. Contact your Toyota dealer.

Item

Function

Default setting

Smart key system (→P. 36)

Smart key system Operation signal (Emergency flashers) Operation signal (Buzzer)

On

On

On

Customized

setting

Off

Off

Off

421

6-2. Customization

Item

Function

Default setting

Wireless remote control

On

Customized

setting

Off

Unlocking operation

Automatic door lock function to be activated if door is not opened after being unlocked Time elapsed before automatic door lock function is activated if door is not opened after being unlocked Operation signal (Emergency flashers) Operation signal (Buzzer) Door lock buzzer Panic function Trunk unlocking func- tion

Driver's door unlocked in one step, all doors unlocked in two

steps

All doors

unlocked in one

step.

On

Off

60 seconds

30 seconds

120 seconds

On

On

On On

On

Off

Off

Off Off

Off

Trunk unlocking opera- tion

Press and hold

Press twice

One short press

Wireless remote con- trol (→P. 47)

422

6-2. Customization

Item

Function

Default setting

Customized

setting

Unlocking using a key

Speed-detecting auto- matic door lock function Opening driver's door unlocks all doors Shifting gears to P unlocks all doors. Shifting gears to posi- tion other than P locks all doors. Light sensor sensitivity Time elapsed before headlights automati- cally turn off after doors are closed Daytime running light system (U.S.A. only)

Time elapsed before lights turn off

Operation when the doors are unlocked Operation after the hybrid system is off Vehicle speed linked seat belt reminder buzzer

Door lock (→P. 50)

Automatic light control system (→P. 149)

Lights (→P. 149)

Illumination (→P. 244)

Seat belt reminder (→P. 351)

Driver's door unlocked in one step, all doors unlocked in two

steps

Off

Off

On

On

All doors

unlocked in one

step.

On

On

Off

Off

Level 3

30 seconds

Level 1 to 5
0 seconds 60 seconds 90 seconds

On

Off

15 seconds

7.5 seconds

30 seconds

On

On

On

Off

Off

Off

423

6-3. Initialization Items to initialize

The following items must be initialized for normal system operation in cases such as after the 12-volt battery is reconnected, or mainte- nance is performed on the vehicle.

Item

When to initialize

Reference

Engine oil mainte- nance data (U.S.A.)

Tire pressure warn- ing system

After changing engine oil

When the tire inflation pressure is charged (such as when changing traveling speed).

P. 295

P. 304

424

Reporting safety defects for U.S. owners

If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway Traffic Safety Administration (NHTSA) in addition to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800-331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign. However, NHTSA can- not become involved in individual problems between you, your dealer, or Toyota Motor Sales, U.S.A., Inc. To contact NHTSA, you may call the Vehicle Safety Hotline toll-free at 1-888-327-4236 to http:// www.safercar.gov ; or write to: Administrator, NHTSA, 1200 New Jersey Ave, S.E., Washington, DC 20590. You can also obtain other from http:// www.safercar.gov.

information about motor vehicle safety

(TTY: 1-800-424-9153); go

426

Seat belt instructions for Canadian owners (in French)

The following is a French explanation of seat belt instructions

extracted from the seat belt section in this manual.

See the seat belt section for more detailed seat belt instructions in English.

Utilisation correcte des ceintures de sécurité

qu'elle

● Tendez la sangle diagonale de sorte couvre complètement l'épaule, sans entrer en contact avec le cou ou glisser de l'épaule.

● Placez la sangle abdominale le plus bas possible sur les hanches.

● Réglez la position du dossier de siège. Asseyez-vous le dos le plus droit possible et calez- vous bien dans le siège.

● Ne vrillez pas la ceinture de

sécurité.

427

Guide de confort de ceinture de sécurité (siège arrière extérieur)

Si la sangle diagonale gêne la personne au niveau du cou, utilisez le guide confort de la ceinture de sécurité.

Sortez le guide confort de sa poche.

Engagez guide.

la ceinture dans

le

Le cordon élastique doit passer sous la ceinture de sécurité.

Bouclez, positionnez et lâchez la ceinture de sécurité.

ÉTAPE

ÉTAPE

ÉTAPE

428

■ Ceintures de sécurité arrière

Si la ceinture de sécurité est sortie de son guide, repassez-la dedans avant de l'utiliser.

Entretien et soin

■ Ceintures de sécurité

Nettoyez avec un chiffon ou une éponge humectée d'eau savonneuse tiède. Profitez de l'occasion pour vérifier régulièrement que les ceintures ne sont pas effilochées, entaillées, ou ne paraissent pas exagérément usées.

ATTENTION

■ Détérioration et usure des ceintures de sécurité

Inspectez les ceintures de sécurité périodiquement. Contrôlez qu'elles ne sont pas entaillées, effilochées, et que leurs ancrages ne sont pas desserrés. N'utilisez pas une ceinture de sécurité défectueuse avant qu'elle ne soit remplacée. Une ceinture de sécurité défectueuse n'apporte aucune garantie de protection de l'occupant en cas d'accident.

429

430

Alphabetical index Alphabetical index

A/C............................................ 174
ABS........................................... 158
Air conditioning filter.............. 319
Air conditioning system

Air conditioning filter............. 319
Automatic air conditioning

system................................ 174

Airbags

Airbag operating conditions.... 91
Airbag precautions for your

child...................................... 95
Airbag warning light.............. 349
Curtain shield airbag

operating conditions............. 92

Curtain shield airbag

precautions .......................... 95

Front passenger occupant

classification system .......... 100
General airbag precautions.... 95
Locations of airbags ............... 88
Modification and disposal of

airbags ................................. 99
Proper driving posture...... 86, 95
Side airbag operating

conditions............................. 92
Side airbag precautions.......... 95
SRS airbags ........................... 88
Antenna.................................... 189
Anti-lock brake system........... 158
Armrest .................................... 261
Ashtray..................................... 256
Audio input .............................. 210
Audio system

Antenna................................ 189
Audio input ........................... 210
AUX adapter......................... 210
CD player/changer ............... 192
MP3/WMA disc..................... 199
Optimal use .......................... 207

Portable music player............210
Radio.....................................186
Steering wheel audio

switch..................................211
Type ......................................183

Automatic air conditioning system ....................................174
Automatic light control system ....................................149
AUX adapter .............................210
Auxiliary boxes ........................251

Back-up lights

Wattage.................................405

Battery

Checking ...............................300
Hybrid battery

(traction battery)....................25

If the vehicle has discharged

12-volt battery.....................385

Preparing and checking before

winter ..................................166
Bluetooth® ................................213
Brake