2011 Toyota 4runner Owners Manual

The engine immobilizer system may not have been deactivated. (→P. 106)

■When the steering lock cannot be released

When starting the engine, the engine switch may seem stuck in the “LOCK” position. To free it, turn the key while turn- ing the steering wheel slightly left and right.

CTH21AS018

■Key reminder function

A buzzer sounds if the driver’s door is opened, while the engine switch is in the “LOCK” or “ACC” position to remind you to remove the key.

165

2-1. Driving procedures

CAUTION

■When starting the engine

Always start the engine while sitting in the driver's seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution when driving

Do not turn the engine switch to the “LOCK” position while driving. If, in an emergency, you must turn the engine off while the vehicle is moving, turn the engine switch only to the “ACC” position to stop the engine. An accident may result if the engine is stopped while driving.

NOTICE

■To prevent battery discharge

Do not leave the engine switch in the “ACC” or “ON” position for long periods of time without the engine running.

■When starting the engine

●Do not crank the engine for more than 30 seconds at a time. This may

overheat the starter and wiring systems.

●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

166

2-1. Driving procedures Engine (ignition) switch (vehicles with a smart key system)

Performing the following operations when carrying the electronic key on your person starts the engine or changes “ENGINE START STOP” switch modes. ■ Starting the engine

STEP 1

STEP 2

STEP 3

Check that the parking brake is set. Check that the shift lever is set in P. Firmly depress the brake pedal. The “ENGINE START STOP” switch indicator will turn green. If the indicator does not turn green, the engine cannot be started.

STEP 4

Press the “ENGINE START STOP” switch.

The engine will crank until it starts or for up to 30 seconds, whichever is less. Continue depressing the brake pedal until the engine is com- pletely started. The engine can be started from any mode.

CTH21AS005

STEP 1

STEP 2

■ Stopping the engine Stop the vehicle. Shift the shift lever to P. Set the parking brake. (→P. 180) Press the “ENGINE START STOP” switch. Release the brake pedal and check that the indicator on the “ENGINE START STOP” switch is off.

STEP 3

STEP 4

STEP 5

167

2-1. Driving procedures

■ Changing “ENGINE START STOP” switch modes Modes can be changed by pressing the “ENGINE START STOP” switch with brake pedal released. (The mode changes each time the switch is pressed.)

Off* The emergency flashers can be used. ACCESSORY mode Some electrical components such as the audio system can be used. The “ENGINE START STOP” switch indicator turns amber. IGNITION ON mode All electrical components can be used. The “ENGINE START STOP” switch indicator turns amber.

*: If the shift lever is in a position other than P when turning off the engine, “ENGINE START STOP” switch will be turned to ACCESSORY mode, not to off.

the

CTH21AS006

168

2

2-1. Driving procedures

When stopping the engine with the shift lever in a position other than P

If the engine is stopped with the shift lever in a position other than P, the “ENGINE START STOP” switch will not be turned off but instead be turned to ACCESSORY mode. Perform the following procedure to turn the switch off:

STEP 1

STEP 2

STEP 3

STEP 4

Check that the parking brake is set. Shift the shift lever to P. Check that the indicator on the “ENGINE START STOP” switch is illuminated in amber and then press the “ENGINE START STOP” switch once. Check that the indicator on the “ENGINE START STOP” switch is off.

■Auto power off function

If the vehicle is left in ACCESSORY or IGNITION ON mode (the engine is not running) for more than an hour with the shift lever in P, the “ENGINE START STOP” switch will automatically turn off. However, this function can- not entirely prevent battery discharge. Do not leave the vehicle with the “ENGINE START STOP” switch in ACCESSORY or IGNITION ON mode for long periods of time when the engine is not running. ■Operation of the “ENGINE START STOP” switch

When operating the “ENGINE START STOP” switch, one short, firm press is enough. If the switch is pressed improperly, the engine may not start or the “ENGINE START STOP” switch mode may not change. It is not necessary to press and hold the switch.

■Electronic key battery depletion

→P. 44

■Conditions affecting operation

→P. 41

■Note for the entry function

→P. 33

169

2-1. Driving procedures

■If the engine does not start

The engine immobilizer system may not have been deactivated. (→P. 106)

■Steering lock

After turning the “ENGINE START STOP” switch off and opening and closing the doors, the steering wheel will be locked due to the steering lock function. Operating the “ENGINE START STOP” switch again automatically cancels the steering lock.

■When the steering lock cannot be released

The green indicator light on the “ENGINE START STOP” switch will flash. Press the “ENGINE START STOP” switch again while turning the steering wheel left and right.

CTH21AS019

■Steering lock motor overheating prevention

To prevent the steering lock motor from overheating, the motor may be sus- pended if the engine is turned on and off repeatedly in a short period of time. In this case, refrain from operating the engine. After about 10 seconds, the steering lock motor will resume functioning.

■When the “ENGINE START STOP” switch indicator flashes in amber

The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately.

■If the electronic key battery is depleted

→P. 528

170

2

2-1. Driving procedures

CAUTION

■When starting the engine

Always start the engine while sitting in the driver’s seat. Do not depress the accelerator pedal while starting the engine under any circumstances. Doing so may cause an accident resulting in death or serious injury.

■Caution while driving

If the vehicle begins to slide due to engine failure or other circumstances, do not lock or open the doors until the vehicle reaches a safe and complete stop. Activation of the steering lock in this circumstance may lead to an acci- dent, resulting in death or serious injury. ■Stopping the engine in an emergency

If you want to stop the engine in an emergency while driving the vehicle, press and hold the “ENGINE START STOP” switch for more than 3 seconds. However, do not touch the “ENGINE START STOP” switch while driving unless in an emergency. If the engine stops while driving, this could lead to an unexpected accident.

171

2-1. Driving procedures

NOTICE

■To prevent battery discharge

●Do not leave the “ENGINE START STOP” switch in ACCESSORY or IGNI-

TION ON mode for long periods of time without the engine running.

●If the indicator on the “ENGINE START STOP” switch is illuminated, the “ENGINE START STOP” switch is not off. When exiting the vehicle, always check that the “ENGINE START STOP” switch is off.

●Do not stop the engine when the shift lever is in a position other than P. If the engine is stopped in another shift lever position, the “ENGINE START STOP” switch will not be turned off but instead be turned to ACCESSORY mode. If the vehicle is left in ACCESSORY mode, battery discharge may occur.

■When starting the engine ●Do not race a cold engine. ●If the engine becomes difficult to start or stalls frequently, have the engine

checked immediately.

■Symptoms indicating a malfunction with the “ENGINE START STOP”

switch If the “ENGINE START STOP” seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction. Contact your Toyota dealer immediately.

172

2-1. Driving procedures Automatic transmission

Select a shift position appropriate for the driving conditions. ■ Shifting the shift lever Standard type

While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.

CTH21AS030

173

2-1. Driving procedures

Multi-mode type

CTH21AS014

Vehicles without a smart key system: While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. Vehicles with a smart key system: While the “ENGINE START STOP” switch is in IGNITION ON mode, move the shift lever with the brake pedal depressed. When shifting the shift lever between P and D, make sure that the vehicle is completely stopped.

174

2-1. Driving procedures

■ Shift position purpose

Shift position

Function

Standard type Parking the vehicle/ starting the engine

Multi-mode type

Reversing Neutral

Normal driving*1

⎯

Position for engine

braking

Position for more

powerful engine braking Position for maximum

engine braking

S mode driving*2

(→P. 176)

⎯

⎯

⎯

*1: To improve fuel efficiency and reduce noises, set the shift lever in the D

position for normal driving.

*2: Selecting shift ranges using S mode restricts the upper limit of the pos- sible gear ranges, controls engine braking forces, and prevents unnec- essary upshifting.

175

2-1. Driving procedures

Changing shift ranges in S mode (multi-mode type)

When the shift lever is in the S position, the shift lever can be oper- ated as follows: Non-Optitron type meter

For upshifting For downshifting

For upshifting For downshifting

Optitron type meter

CTH21AS025

CTH21AS015

The initial shift range in S mode is set automatically to “4” according to vehicle speed. However, the initial shift range may be set to “3” if AI-SHIFT has operated while the shift lever was in the D position. (→P. 177) ■ Shift ranges and their functions

● You can choose from 5 levels of engine braking force. ● A lower shift range will provide greater engine braking force than

a higher shift range, and the engine speed will also increase.

176

2-1. Driving procedures

■Downshifting restrictions (standard type)

The maximum allowable speeds are as follows.

Downshifting

Maximum speed mph (km/h)

3 → 2
2 → L

67 (108) 32 (52)

■S mode (multi-mode type)

When the shift range is “3” or lower, holding the shift lever toward “+” sets the shift range to “5”.

■AI-SHIFT

AI-SHIFT automatically selects the optimal gear according to driver perfor- mance and driving conditions. Standard type AI-SHIFT automatically operates when the shift lever is in the D position. Multi-mode type AI-SHIFT automatically operates when the shift lever is in the D position. (Shifting the shift lever to the S position cancels the function.)

■When driving with the cruise control system

Standard type The engine brake will not operate when downshifting from D to 3. (→P. 209) Multi-mode type Engine braking will not occur in S mode, even when downshifting to “4”. (→P. 209)

■If the shift lever cannot be shifted from P →P. 593
■If the “S” indicator does not come on even after shifting the shift lever

to S (multi-mode type) This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.)

177

2-1. Driving procedures

■Downshift restriction warning buzzer (S mode in multi-mode type)

To help ensure safety and driving performance, downshifting operation may sometimes be restricted. In some circumstances, downshifting may not be possible even when the shift lever is operated. (A buzzer will sound twice.)

CAUTION

■When driving on slippery road surfaces Do not accelerate or shift gears suddenly. Sudden changes in engine braking may cause the vehicle to spin or skid, resulting in an accident.

178

2

2-1. Driving procedures Turn signal lever

The turn signal lever can be used to show the following intentions of the driver:

Right turn Left turn Lane change to the right (push and hold the lever partway) The right hand signals will flash until you release the lever. left Lane change (push and hold the lever partway) The left hand signals will flash until you release the lever.

the

to

CTH21AS028

■Turn signals can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

■If the indicator flashes faster than usual

Check that a light bulb in the front or rear turn signal lights has not burned out.

179

2-1. Driving procedures Parking brake

BRAKE Type A

BRAKE Type B

Type C

CTH21AS026

To set the parking brake, fully depress the parking brake pedal with your left foot while depressing the brake pedal with your right foot. (Depressing the pedal again releases the parking brake.)

■Usage in winter time

See “Winter driving tips” for parking brake usage in winter time. (→P. 275)

NOTICE

■Before driving

Fully release the parking brake. Driving the vehicle with the parking brake set will lead to brake components overheating, which may affect braking performance and increase brake wear.

180

2-1. Driving procedures Horn

To sound the horn, press on or close to the

mark.

CTH21AS022

■After adjusting the steering wheel

Make sure that the steering wheel is securely locked. The horn may not sound if the steering wheel is not securely locked. (→P. 86)

181

2-2. Instrument cluster Gauges and meters

Non-Optitron type meters

Optitron type meters

182

2

2-2. Instrument cluster

Tachometer Displays the engine speed in revolutions per minute Speedometer Displays the vehicle speed Display change button →P. 184
Engine coolant temperature gauge Displays the engine coolant temperature Fuel gauge Displays the quantity of fuel remaining in the tank Eco Driving Indicator Zone Display →P. 185
Odometer, trip meter and average fuel consumption display →P. 184
Shift position and shift range indicators →P. 173
Voltmeter Displays the charge state

183

2-2. Instrument cluster

Switching the display

Items displayed can be switched by pressing the display change button.

■ Odometer

Displays the total distance the vehicle has been driven.

■ Trip meter

Displays the distance the vehicle has been driven since the meter was last reset. Trip meters “A” and “B” can be used to record and display different distances independently. Pressing and holding the display change button will reset the trip meter that is currently displayed.

184

2

2-2. Instrument cluster

■ Eco Driving Indicator and average fuel consumption Non-Optitron type meter

CTH22AS054

Indicator Zone

Eco Driving Indicator Light During Eco-friendly acceleration (Eco driving), Eco Driving Indica- tor Light will turn on. Eco Driving Display Suggests Zone of Eco driving with current Eco driving ratio based on acceleration. Zone of Eco driving Eco driving ratio based on acceleration In case over-use of the accelera- tor causes the vehicle to exceed Zone of Eco driving, the right of Eco Driving Indicator Zone Dis- play will blink and Eco Driving Indicator Light will turn off. Average fuel consumption Displays the average fuel con- sumption since the function was reset. Pressing and holding the display change button will reset the aver- age fuel consumption.

185

Indicator Zone

Eco Driving Indicator Light During Eco-friendly acceleration (Eco driving), Eco Driving Indica- tor Light will turn on. Eco Driving Display Suggests Zone of Eco driving with current Eco driving ratio based on acceleration. Zone of Eco driving Eco driving ratio based on acceleration In case over-use of the accelera- tor causes the vehicle to exceed Zone of Eco driving, the right of Eco Driving Indicator Zone Dis- play will blink and Eco Driving Indicator Light will turn off. Average fuel consumption Displays the average fuel con- sumption since the function was reset. Pressing and holding the display change button will reset the aver- age fuel consumption.

CTH22AS055

2-2. Instrument cluster

Optitron type meter

186

2-2. Instrument cluster

■ Eco Driving Indicator Light customization Non-Optitron type meter

Eco Driving Indicator Light can be activated or deactivated by pressing and holding the display change button.

Optitron type meter

Eco Driving Indicator Light can be activated or deactivated by pressing and holding the display change button.

Instrument panel light control

The brightness of the instrument panel lights can be adjusted.

Brighter Darker

CTH22AS010

187

2-2. Instrument cluster

■The meters and display illuminate when (Optitron type meter)

Vehicles without a smart key system: The engine switch is in the “ON” position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

■Eco Driving Indicator operates when

The vehicle is being driven with the shift lever in D.

■When the average fuel consumption is reset

The average fuel consumption displayed on the accessory meter and “Past Record” screen of the navigation system (if equipped) will be reset at the same time.

■The brightness of the instrument panel lights (Optitron type meter)

When the headlight switch is turned to on, the brightness will be reduced slightly unless the control dial is turned fully upward.

NOTICE

■To prevent damage to the engine and its components

●Do not let the indicator needle of the tachometer enter the red zone, which

indicates the maximum engine speed.

●The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (→P. 604)

■While driving (Optitron type meter)

When the voltmeter indicates more than 19 V or less than 9 V, the battery may be malfunctioning. Have your vehicle checked at your Toyota dealer.

188

2-2. Instrument cluster Indicators and warning lights

The indicator and warning lights on the instrument cluster and cen- ter panel inform the driver of the status of the vehicle’s various sys- tems. Instrument cluster (non-Optitron type meter)

Instrument cluster (Optitron type meter)

CTH22AS052

CTH22AS053

189

2-2. Instrument cluster

Center panel

CTH22AS015

190

2

2-2. Instrument cluster

■ Indicators

The indicators inform the driver of the operating state of the vehicle’s various systems.

Turn signal indicator (→P. 179)

Headlight high beam indicator (→P. 202)

Headlight indicator (→P. 198)

Tail light indicator (→P. 198)

Front fog light indicator (→P. 204)

Cruise control indicator (→P. 209)

Cruise control set indi- cator (→P. 209)

Slip indicator (→P. 254)

VSC off indicator (→P. 255)

(Canada)

(if equipped)

(if equipped)

(if equipped)

(if equipped)

(if equipped)

(if equipped)

(if equipped)

“TRC OFF” indicator (→P. 255)

Roll sensing of curtain shield airbags off indica- tor (→P. 128)

Four-wheel drive indica- tor (→P. 223)

Downhill assist control system indicator (→P. 238)

Low speed four-wheel drive indicator (→P. 223, 226)

Rear differential lock indicator (→P. 235)

Center differential lock indicator (→P. 226)

“A-TRAC” indicator (→P. 230)

“AUTO LSD” indicator (→P. 232)

“TRAC OFF” indicator (→P. 255)

Multi-terrain Select indi- cator (→P. 245)

(if equipped)

(U.S.A.)

(Canada)

(if equipped)

(U.S.A.)

191

2-2. Instrument cluster

(if equipped)

Crawl Control indicator (→P. 241)

Security indicator (→P. 106, 109)

Eco Driving Indicator Light (→P. 185)

Intuitive parking assist indicator (→P. 213)

(if equipped)

SRS airbag on-off indi- cator (→P. 130)

*: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system) to indicate that a system check is being performed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

192

2-2. Instrument cluster

■ Warning lights

Warning lights inform the driver of malfunctions in any of the vehicle’s systems. (→P. 565)

(if equipped) (if equipped) (if equipped)

(Canada)

(U.S.A.)

(U.S.A.)

(Canada)

(if equipped)

(if equipped)

(if equipped)

*: These lights turn on when the “ENGINE START STOP” switch is turned to IGNITION ON mode (vehicles with a smart key system) or the engine switch is turned to the “ON” position (vehicles without a smart key system) to indicate that a system check is being per- formed. They will turn off after the engine is started, or after a few seconds. There may be a malfunction in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer.

CAUTION

■If a safety system warning light does not come on

Should a safety system light such as the ABS or SRS warning light not come on when you start the engine, this could mean that these systems are not available to help protect you in an accident, which could result in death or serious injury. Have the vehicle inspected by your Toyota dealer immediately if this occurs.

193

2-2. Instrument cluster Accessory meter

The accessory meter presents the driver with a variety of driving- related data including the current outside air temperature.

” button

” button

“MODE/ “SET/ Trip information (→P. 195) Displays driving range and average fuel consumption Outside temperature display (→P. 433) Compass (→P. 450) Clock (→P. 431) H (Hour) button (→P. 431) M (Minute) button (→P. 431) Multi-terrain Select display (→P. 245) Automatically displayed when using Multi-terrain Select

194

2

2-2. Instrument cluster

Trip information

Items displayed can be switched by pressing the “MODE/ ■ Driving range

” button.

(vehicles without Multi-terrain Select)

Displays the estimated maximum distance that can be driven with the quantity of fuel remaining • This distance is computed based on your average fuel consumption. As a result, the actual distance that can be driven may differ from that displayed.

• When only a small amount of fuel is added to the

tank, the display may not be updated.

(vehicles with Multi-terrain Select)

■ Average fuel consumption

Displays the average fuel consumption since the function was reset

Pressing and holding the “SET/ the average fuel consumption.

” button will reset

(vehicles without Multi-terrain Select)

(vehicles with Multi-terrain Select)

195

2-2. Instrument cluster

Accessory meter light control

The daytime brightness of the accessory meter can be adjusted.

STEP 1

STEP 2

Turn the headlight switch off. Press and hold the “MODE/ Press the “MODE/

” or “SET/ Vehicles without Multi-terrain Select

STEP 3

” button.

” button.

Vehicles with Multi-terrain Select

STEP 4

Press and hold the “SET/

” button.

196

2

2-2. Instrument cluster

■When the average fuel consumption is reset

The average fuel consumption displayed on the instrument cluster and “Past Record” screen of the navigation system (if equipped) will be reset at the same time.

■Adjusting the brightness of the accessory meter

●If left idle for approximately 6 seconds or more while adjusting, the dis-

play will revert to the trip information display.

●When the parking lights are on, the brightness of the accessory meter

can be adjusted only with the instrument panel light control.

●If the “MODE/

” button is pressed and held when the accessory meter light control is displayed, the display will switch to compass calibration. (→P. 450)

■Liquid crystal display

Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem with continu- ing to use the display.

NOTICE

■The accessory meter at low temperatures

Allow the interior of the vehicle to warm up before using the liquid crystal dis- play. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed.

197

2-3. Operating the lights and wipers Headlight switch

The headlights can be operated manually or automatically. Turning the end of the lever turns on the lights as follows: Type A

The daytime running lights turn on. The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above turn on. The daytime running lights turn off.

CTH23AS033

198

2

2-3. Operating the lights and wipers

Type B

is

(when

The headlights, park- ing lights, daytime run- ning lights and so on turn on and off auto- the matically START “ENGINE STOP” switch in IGNITION ON mode). The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above turn on. The daytime running lights turn off.

CTH23AS034

199

2-3. Operating the lights and wipers

Type C

The daytime running lights turn on. The side marker, park- ing, tail, license plate and instrument panel lights turn on. The headlights and all the lights listed above turn on.

CTH23AS030

200

2

2-3. Operating the lights and wipers

Type D

(when

The daytime running lights turn on. The headlights, park- ing lights, daytime run- ning lights and so on turn on and off auto- matically the START “ENGINE STOP” switch in IGNITION ON mode). The side marker, park- ing, tail, license plate, daytime running lights and instrument panel lights turn on. The headlights and all the lights listed above turn on.

is

CTH23AS031

201

2-3. Operating the lights and wipers

Turning on the high beam headlights

With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off. Pull the lever toward you and release it to flash the high beams once. You can flash the high beams with the headlights on or off.

CTH23AS032

■Daytime running light system

●To make your vehicle more visible to other drivers, the daytime running lights turn on automatically whenever the engine is started and the park- ing brake is released. Daytime running lights are not designed for use at night. Type A and B: Daytime running lights can be turned off by operating the switch.

●Compared to turning on the headlights, the daytime running light system offers greater durability and consumes less electricity, so it can help improve fuel economy.

■Headlight control sensor (if equipped)

The sensor may not function properly if an object is placed on the sensor, or any- thing that blocks the sensor is affixed to the windshield. the sensor Doing so detecting the level of ambient light and may cause the automatic headlight sys- tem to malfunction.

interferes with

CTH23AS012

202

2-3. Operating the lights and wipers

■Automatic light off system

Vehicles without a smart key system ●When the headlights come on: The headlights and tail lights turn off 30
seconds after a door is opened and closed if the engine switch is turned to the “ACC” or “LOCK” position. (The lights turn off immediately if

on the key is pressed after all the doors are locked.)

●When only the tail lights come on: The tail lights turn off automatically if the engine switch is turned to the “ACC” or “LOCK” position and the driver’s door is opened.

or

To turn the lights on again, turn the engine switch to the “ON” position, or turn the lights off and then back to Vehicles with a smart key system ●When the headlights come on: The headlights and tail lights turn off 30
seconds after a door is opened and closed if the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. (The lights turn off immediately if on the key is pressed after all the doors are locked.)

●When only the tail lights come on: The tail lights turn off automatically if the “ENGINE START STOP” switch is turned off and the driver’s door is opened.

To turn the lights on again, turn the “ENGINE START STOP” switch to IGNI- TION ON mode, or turn the light switch off and then back to or

■Customization that can be configured at Toyota dealer

Settings (e.g. light sensor sensitivity) can be changed. (Customizable features →P. 640)

NOTICE

■To prevent battery discharge

Do not leave the lights on longer than necessary when the engine is not run- ning.

203

2-3. Operating the lights and wipers Fog light switch∗

The fog lights secure excellent visibility in difficult driving condi- tions, such as in rain and fog.

Turns the front fog lights off Turns the front fog lights on

CTH23AS010

■Fog lights can be used when

The headlights are on in low beam.

204

∗: If equipped

2

2-3. Operating the lights and wipers Windshield wipers and washer

When intermittent windshield wiper operation is selected, the wiper interval can be adjusted. The wiper operation is selected by moving the lever as follows.

windshield

Intermittent wiper operation Low speed windshield wiper operation High wiper operation Temporary operation

speed windshield

the

Increases intermittent windshield wiper frequency Decreases the intermittent windshield wiper frequency

CTH23AS027

CTH23AS028

205

2-3. Operating the lights and wipers

Washer/wiper dual opera- tion The wipers will automatically operate a couple of times after the washer squirts.

CTH23AS029

■The windshield wipers and washer can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

■If no windshield washer fluid sprays

Check that the washer nozzles are not blocked if there is washer fluid in the windshield washer fluid reservoir.

NOTICE

■When the windshield is dry

Do not use the wipers, as they may damage the windshield.

■When the washer fluid tank is empty

Do not operate the switch continually as the washer fluid pump may over- heat.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

206

2

2-3. Operating the lights and wipers Rear window wiper and washer

Before operating the rear window wiper and washer switch, make sure the back window is completely closed. (→P. 94) The wiper operation is selected by moving the lever as follows:

Intermittent window wiper operation Normal window wiper oper- ation Washer/wiper dual opera- tion Washer/wiper dual opera- tion The wiper will automatically operate a couple of times after the washer squirts. (After operating several times, the wiper operates one more time after a short delay to pre- vent dripping.)

CTH23AS035

■The rear window wiper and washer can be operated when

●Vehicles without a smart key system: The engine switch is in the “ON”

position. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode.

●The back window is completely closed.

■Intermittent window wiper operation

●When intermittent window wiper operation mode is selected, the wiper

will operate a couple of times and then switch to intermittent operation.

●During intermittent operation, the wiper stops temporarily at the reversing

position.

207

2-3. Operating the lights and wipers

■When the rear window wiper and washer switch is turned off

The rear wiper will stop operation, and return to the retracted position after approximately 3 seconds. However, if the engine switch is turned to the “ACC” or “LOCK” position (vehicles without a smart key system) or the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off (vehicles with a smart key sys- tem) while the rear wiper is operating, the rear wiper will stop at that position and will not return to the retracted position.

■If no washer fluid sprays

Check that the washer nozzle is not blocked if there is washer fluid in the washer fluid reservoir.

■Customization that can be configured at Toyota dealer

Settings (e.g. drip prevention function) can be changed. (Customizable features →P. 640)

NOTICE

■When the rear window is dry

Do not use the wiper, as it may damage the rear window.

■When the washer fluid tank is empty

Do not operate the switch continually as the washer fluid pump may over- heat.

■When a nozzle becomes blocked

Do not try to clear it with a pin or other object. The nozzle will be damaged.

208

2-4. Using other driving systems Cruise control

Use cruise control to maintain a set speed without depressing the accelerator pedal.

Indicators Cruise control switch

■ Setting the vehicle speed

CTH24AS001

STEP 1

Press the “ON-OFF” button to activate the cruise control. the button again

Press deactivate the cruise control.

to

STEP 2

Accelerate or decelerate to the desired speed, and push the lever down to set the speed.

CTH24AS002

CTH24AS057

209

2-4. Using other driving systems

■ Adjusting the set speed

Increases the speed Decreases the speed Hold the lever until the desired speed setting is obtained. Fine adjustment of the set speed can be made by lightly pushing the lever up or down and releasing it.

CTH24AS004

■ Canceling and resuming the constant speed control

Pulling the lever toward you cancels the constant speed control. The speed setting is also can- celed when the brakes are applied. Pushing resumes speed control.

lever up constant

the the

CTH24AS005

210

2-4. Using other driving systems

■Cruise control can be set when

●The shift lever is in D or “3” (standard type), or in D, or “4” or “5” range of

S has been selected (multi-mode type).

●Vehicle speed is above 25 mph (40 km/h).

■Accelerating

The vehicle can be accelerated normally. After acceleration, the set speed resumes.

■Automatic cruise control cancelation

Cruise control will stop maintaining the vehicle speed in any of the following situations: ●Actual vehicle speed falls more than 10 mph (16 km/h) below the preset

vehicle speed. At this time, the memorized set speed is not retained.

●Actual vehicle speed is below 25 mph (40 km/h). ●VSC is activated.

■If the cruise control indicator light flashes

Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. If the cruise control speed cannot be set or if the cruise control cancels immediately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer.

211

2-4. Using other driving systems

CAUTION

■To avoid operating the cruise control by mistake

Switch the cruise control off using the “ON-OFF” button when not in use.

■Situations unsuitable for cruise control

Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury. ●In heavy traffic ●On roads with sharp bends ●On winding roads ●On slippery roads, such as those covered with rain, ice or snow ●On steep hills

Vehicle speed may exceed the set speed when driving down a steep hill.

●When your vehicle is towing anything

212

2-4. Using other driving systems Intuitive parking assist∗

The distance from your vehicle to nearby obstacles when parallel parking or maneuvering into a garage is measured by the sensors and communicated via an indicator and a buzzer. Always check the surrounding area when using this system. ■ Types of sensors

Rear corner sensors Rear center sensors

■ Intuitive parking assist switch

intuitive parking

Turns the assist on/off When on, the indicator light comes on and the buzzer sounds to inform the driver that the system is operational.

CTH24AS008

∗: If equipped 213

2-4. Using other driving systems

The indicator and buzzer

When a sensor detects an obstacle, the direction of the obstacle is indicated and the buzzer sounds. ■ Sensor operation and distance to an obstacle

The system operates when the vehicle approaches an obstacle, as shown by the following table.

Rear corner sensors

Distance to an obstacle ft. (cm) Approximately 1.6 - 1.2 (50 - 37.5) Approximately 1.2 - 0.8 (37.5 - 25) Approximately 0.8 or less (25 or less)

Rear center sensors

Indicator and buzzer

Intermittent

Fast intermittent

Continuously

Distance to an obstacle ft. (cm)

Indicator and buzzer

Approximately 4.9 - 2.0 (150 - 60) Approximately 2.0 - 1.5 (60 - 45) Approximately 1.5 - 1.2 (45 - 35) Approximately 1.2 or less (35 or less)

Intermittent

Fast intermittent

Very fast intermittent

Continuously

214

2

Detection range of the sensors

2-4. Using other driving systems

Approximately 1.6 ft. (50 cm) Approximately 4.9 ft. (150 cm) The diagram shows the detection range of the sensors. Note that the sensors cannot detect obsta- cles that are extremely close to the vehicle. The range of the sensors may change depending on the shape of the object etc.

■Intuitive parking assist can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion and the shift lever is in R. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode and the shift lever is in R.

215

2-4. Using other driving systems

■Sensor detection information

●Certain vehicle conditions and the surrounding environment may affect the ability of a sensor to correctly detect an obstacle. Particular instances where this may occur are listed below. • There is dirt, snow or ice on a sensor. • A sensor is frozen. • A sensor is covered in any way. • The vehicle is leaning considerably to one side. • On an extremely bumpy road, on an incline, on gravel, or on grass • The vicinity of the vehicle is noisy due to vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.

• There is another vehicle equipped with parking assist sensors in the

• A sensor is coated with a sheet of spray or heavy rain. • A bumper or sensor receives a strong impact. • The vehicle is approaching a tall or right-angled curb. • In harsh sunlight or intense cold weather • A non-genuine Toyota suspension (lowered suspension etc.) is

vicinity.

installed.

In addition to the examples above, there are instances in which, because of their shape, signs and other objects may be judged by a sensor to be closer than they are. ●The shape of the obstacle may prevent a sensor from detecting it. Pay

particular attention to the following obstacles: • Wires, fences, ropes, etc. • Cotton, snow and other materials that absorb sound waves • Sharply-angled objects • Low obstacles • Tall obstacles with upper sections projecting outwards in the direction

of your vehicle

216

2

2-4. Using other driving systems

■When the system malfunctions

If a malfunction occurs and no obstacles have been detected, the indicator flashes and the buzzer sounds for approximately 7 seconds. If the indicator comes on and stays on after that, have the vehicle inspected by your Toyota dealer.

■Customization that can be configured at Toyota dealer

Settings (e.g. buzzer volume) can be changed. (Customizable features →P. 640)

■Certification

For vehicles sold in the U.S.A. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions; (1) This device may not cause harmful interfer- ence, and (2) This device must accept any interference received, including interference that may cause undesired operation. For vehicles sold in Canada This ISM device complies with Canadian ICES-001. Cet appareil ISM est conforme a la norme NMB-001 du Canada.

CAUTION

■Caution when using the intuitive parking assist-sensor

Do not attach any accessories within the sensor range. Doing so may result in the vehicle being unable to be driven safely and pos- sibly cause an accident.

NOTICE

■Notes when washing the vehicle

Do not apply intensive bursts of water or steam to the sensor area. Doing so may result in the sensor malfunctioning.

217

2-4. Using other driving systems Rear view monitor system (rear view mirror-attached type)∗

The rear view monitor assists the driver by displaying an image of the area behind the vehicle while reversing. The image is displayed in reverse on the screen. This reversed image is a similar image to the one on the inside rear view mirror.

The rear view image is dis- played when the shift lever is in R. •

If the shift lever is shifted out of R, the screen is turned off.

• The screen remains on for

approximately 5 minutes.

Multi-mode type

Standard type

CTH24AS063

218

∗: If equipped

2

2-4. Using other driving systems

■The rear view monitor system can be operated when

Vehicles without a smart key system: The engine switch is in the “ON” posi- tion and the shift lever is in R. Vehicles with a smart key system: The “ENGINE START STOP” switch is in IGNITION ON mode and the shift lever is in R.

■Switching the screen on/off

CTH24AS014

When the screen is displayed, press the “AUTO” button on the inside rear view mirror to switch the screen on/off. Screen on: Green indicator comes on. Screen off: Orange indicator comes on.

In the following situation, the display will be re-enabled if it has been turned off: Vehicles without a smart key system The engine switch is turned to the “ON” position. Vehicles with a smart key system The “ENGINE START STOP” switch is turned to IGNITION ON mode.

219

2-4. Using other driving systems

■Displayed area

The area covered by the camera is lim- ited. Objects that are close to either cor- ner of the bumper or under the bumper cannot be seen on the screen. The area displayed on the screen may vary depending on vehicle orientation or road conditions.

Corners of bumper

CTH24AS059

■Rear view monitor system camera

CTH24AS067

The rear view monitor system camera is located on the back door as shown in the illustration. The camera uses a special lens. The distance of the image that appears on the screen differs from the actual distance. In the following cases, it may become dif- ficult to see images on the screen even when the system is functioning correctly: ●The vehicle is in a dark area, such as at

night. ●The

temperature near

the

lens

is

extremely high or low.

CTH24AS012

220

2-4. Using other driving systems

●Water droplets are on the camera lens or humidity is high, such as when it rains.

●Foreign matter, such as snow or mud,

adheres to the camera lens.

●When the camera has scratches or dirt

on it.

●The sun or headlights are shining

directly into the camera lens.

■Smear effect

●A bright object such as a white wall is reflected in the mirror surface over the monitor.