2005 Toyota 4runner Owners Manual

(four−wheel drive models)

D Traction control system

(two−wheel drive models)

D Active traction control system

(four−wheel drive models)

182

than

“HI” (high) mode— The vehicle height is about 40 mm (1.6
in.) higher at rear the “N” mode height. This mode is suitable when driving on the bumpy roads and through water. However, when the vehicle speed exceeds about 30 km/h (19 mph) or over in the “HI” mode, the “N” mode is automatically selected.

CAUTION

The “HI” mode should be used for severe off−road driving condition only. Because the vehicle’s center of gravity is higher in this setting, the vehicle may become unstable when turning abruptly, resulting in accident.

’05 4Runner_U (L/O 0409)

the

rear

than

lower at

“LO” (low) mode— The vehicle height is about 20 mm (0.8
in.) “N” mode height. This mode allows you easy access to the vehicle (getting in and out) and easy load- ing and unloading operation. This mode is available when the vehicle speed is under about 12 km/h (7 mph).

NOTICE

Use the “LO” mode when the vehicle is stopped. Otherwise, when the ve- hicle speed exceeds about 12 km/h (7
mph), “N” mode is selected automati- cally. So be careful when you drive in any place where the overhead height is limited.

(b) Vehicle height mode changing con-

dition

To change the vehicle height, it is neces- sary to meet the following conditions. D The engine should be running. D The height control “OFF” indicator light

should go off.

D When selecting a mode, there is a ve- hicle speed limit. Refer to the following table.

Yes = The mode can be selected. No = The mode cannot be selected.

“LO” mode

“N” mode

“HI” mode

Yes

Yes

Yes

No

Yes

Yes

No

Yes

No

Under about 12 km/h (7 mph) Under about 30 km/h (19 mph)

About 30 km/h (19 mph) or over

In the following cases, the rear height control suspension will not operate. D The underbody of

the vehicle has

touched the surface on bumpy roads.

D The area around the rear suspension

is coated with ice.

183

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

If the vehicle is moved to its usual loca- tion or the ice is removed and the height select switch the vehicle height control cannot be operated. In this case, turn off and restart the engine, then push the control switches.

is pressed,

184

’05 4Runner_U (L/O 0409)

(c) Vehicle height adjustment To change the mode, push the height select switch on either side of “Ɯ” (higher) or “Ɲ” (lower). The height control indicator light indicates which mode is selected. (See “(e) Height control indicator light” described below.) Selecting the “HI” mode— Push the height select switch on the “Ɯ” side when is under about 30 km/h (19 mph). To change the “N” mode to “HI”, push the switch once.

the vehicle speed

To change the “LO” mode to “HI”, push the switch twice. It takes about 30 sec- onds until the “LO” mode changes to the “HI” mode. Selecting the “N” mode— To change the “HI” mode to “N”, push the height select switch on the “Ɲ” side once. To change the “LO” mode to “N”, push the height select switch on the “Ɯ” side once. Selecting the “LO” mode— Push the height select switch on the “Ɲ” side while the vehicle is stopped. To change the “N” mode to “LO”, push the switch once. To change the “HI” mode to “LO”, push the switch twice. Even if the engine is stopped while the vehicle height is being lowered, the opera- tion continues for up to 25 seconds. If, within this 25 seconds, any of the side doors or the back door is opened, opera- tion will continue for a further 15 seconds.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

NOTICE

z If the vehicle height is changed fre- quently when the vehicle is heavily loaded, the compressor may over- heat, causing the vehicle height ad- justment operation to stop.

the vehicle

z Before you lower the vehicle height with the height select switch, check under to make sure nothing to damage the vehicle or no one to be injured is there and that the underbody of the vehicle does not touch the ground.

z After unloading, the height of a ve- hicle equipped with the rear height control air suspension becomes slightly higher than the normal ve- hicle height. Take sufficient care where the overhead height is re- stricted.

z Do not select the “LO” mode in the bumpy roads. If the underbody of the vehicle touches the rugged road surface, the vehicle may be dam- aged.

’05 4Runner_U (L/O 0409)

(d) Turning off the rear height control

air suspension

To turn off the rear height control air suspension with the vehicle stopped, push the “HEIGHT CONTROL OFF” switch. The height control “OFF” indi- cator light comes on and the vehicle height is fixed in the same mode as the height control switch is pushed. This status is memorized in the system even after the engine is stopped. If you push the switch again, the height control “OFF” indicator light goes out and the rear height control air suspension is turned on. Even after the rear height control air sus- pension is turned off with the “HEIGHT the vehicle CONTROL OFF” switch, speed exceeds 30 km/h (19 mph), the rear height control air suspension automat- ically selects the “N” mode.

if

185

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

CAUTION

If you drive through deep water over about 700 mm (28 in.) in depth, put the vehicle height in the “HI” mode with the height select switch and then turn off the rear height control air suspension by pushing the “HEIGHT CONTROL OFF” switch.

NOTICE

the

z When jacking up or installing tire chains, be sure to turn off the rear height control air suspension by pushing “HEIGHT CONTROL OFF” switch and stop the engine. Otherwise, the vehicle height may change because of the automatic leveling function, resulting in an un- expected accident.

z If your vehicle must be towed, put the vehicle height in the “N” mode and turn off the rear height control air suspension. Otherwise, the ve- hicle height may change because of the automatic leveling function, re- sulting in an unexpected accident.

186

’05 4Runner_U (L/O 0409)

z If your vehicle gets ditched, turn off the rear height control air suspen- sion with the “HEIGHT CONTROL OFF” switch. Otherwise, the vehicle height may change because of the automatic leveling function resulting in an unexpected accident.

(e) Height control indicator lights 1. Height control indicator lights 2. Height control “OFF” indicator light When the ignition switch is turned on, all the indicator lights come on. The indicator light showing the present mode only re- mains on and all other lights go off after a few seconds. This means the system operates correctly.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

1. The present mode indicator light goes indicator

the selected mode

off and light blinks.

2. The selected mode indicator light goes (The vehicle height does not indicator

off. change.) The present mode light comes on again.

indicator

In this case, even if the vehicle is moved to its usual location or the ice is removed and the height select switch is pressed, vehicle height control cannot be operated. Turn off the engine once and then restart it. Height control “OFF” light: When the ignition switch is turned on, this light comes on. If it goes out after a few seconds, the rear height control air sus- pension operates correctly. If you push the “HEIGHT CONTROL OFF” switch, the rear height control air suspension is turned off. The height control “OFF” light comes on. In the following cases, there is a problem somewhere in the rear height control air suspension. Although there is no problem to continue normal driving, have the rear height control air suspension checked by your Toyota dealer as soon as possible.

indicator

If you change the vehicle height mode, the indicator lights change as follows: When changing the vehicle height from the “N” mode to “HI”: 1. The “N” mode indicator light goes off and the “HI” mode indicator light blinks. 2. After the vehicle height control reaches the “HI” mode, the “HI” mode indicator light remains on. the underbody of

If the vehicle has touched the surface on bumpy roads or the area around the rear suspension is coated with ice, the vehicle height cannot be lowered with the height select switch. The height control indicator lights change as follows:

D The height control “OFF” indicator light does not come on when the ignition switch is turned on.

D The height control “OFF” indicator light

blinks.

(f) Parking and stopping tips If you immediately stop the engine to park the vehicle after off−road driving, the ve- hicle height is lowered slightly as the ve- hicle becomes cool. When parking, make sure there is nothing that will be in con- tact with the underbody of the vehicle. When you start the engine, the vehicle returns to the previous height. If you park the vehicle for a long time, the vehicle height may be gradually low- ered. When parking for a long time, make sure there is nothing that will be in con- tact with the underbody of the vehicle. When you start the engine, the vehicle returns to the previous height. If you stop the engine, the vehicle height may change the change temperature. When you start the engine, the vehicle returns to the previous height.

in accordance with

the

in

187

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

(g) Rear height control failure warning If there is a problem somewhere in the rear height control air suspension, the “N” mode is automatically selected. If this oc- curs, indicator light blinks and the vehicle height control cannot be activated until the malfunction is corrected. If this is the case, bring your vehicle to your Toyota dealer as soon as possible and have it checked.

the height control “OFF”

Tire pressure warning system— The tire pressure warning system is de- signed to provide warning when tire inflation pressure of one or more of your tires (including the spare tire) is low. The low tire pressure warning light comes on to inform you that low tire inflation pressure may hamper driving.

LOW TIRE PRESSURE WARNING LIGHT This light comes on when the ignition key is turned to the “ON” position. It goes off after a few seconds. This indicates that the tire pressure warning system is func- tioning properly.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

188

’05 4Runner_U (L/O 0409)

tire

If the low tire pressure warning light comes on or blinks, do the following. If the warning light comes on: Stop your vehicle in a safe place as soon as possible and check that the inflation pressure of all tires (including the spare tire) is as specified on the tire and loading information label. (See “Checking inflation pressure” on page 379 in Section 7−2.) If the warning light comes on even after tire inflation pressure adjustment, you may have a flat tire. If you have a flat tire, replace it with the spare tire. For details, see “If you have a flat tire” on page 333 in Section 4. The warning light goes off a few minutes after air is put into the deflated tire. This warning light may turn on due to natural causes such as natural air leaks or tire pressure changes caused by tem- perature. In this case, adjusting the tire pressure will turn off the warning light.

CAUTION

NOTICE

When the tire pressure warning light comes on, observe the following in- structions: D Depending on

the conditions, re- duce to an appropriate speed as soon as possible.

D Adjust the tire pressure to the spe-

cified level as soon as possible.

D Avoid abrupt steering wheel maneu- vering and braking. Tire deteriora- tion may reduce steering wheel con- trol and brake effectiveness. This may lead to serious injury or death. D The tire pressure warning system may not activate immediately if sud- den bursts of air leakage occur.

z Do not use liquid sealants for a flat tire as air pressure sensors will be damaged.

z When the tires must be repaired or replaced, have them repaired or re- placed by the nearest Toyota dealer or authorized tire dealer. The tire pressure sensors will be affected by the installation or removal of tires. z The tire pressure warning system is not to be used as a substitute for regular to check the air pressure in the tires on a regular basis.

inspections. Be sure

z When the tires must be replaced, replace the grommets for air pres- sure sensors as well.

189

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

CAUTION

D The use of non−genuine wheels will cause the air pressure sensors to transmit the electronic code in dif- ferent manner, resulting in the sys- tem failure.

D The use of different type of tires with genuine wheels may also cause the malfunction of the sys- tem.

If the warning light blinks: The tire pressure warning system may be malfunctioning. Contact your Toyota dealer. SYSTEM MALFUNCTION The tire pressure warning system does not function properly under certain cir- cumstances. In the following cases, the low tire pressure warning light may not come on even if the tire inflation pres- sure is low, or it may come on when the tire is actually normal. D Electric devices or facilities using simi- lar radio wave frequencies are nearby. D A radio set to similar frequencies is in

inflation pressure

use.

D A lot of snow or ice covers the ve- hicle, in particular, around the wheels or wheel housings.

D The tires are not equipped with an air

pressure sensor.

D Snow tires or tire chains are used. D Non−genuine Toyota wheels are used. D The sensor battery is expired. D Radio waves from the air pressure sen- sor installed on the spare tire cannot be received.

190

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

CAUTION

For vehicles sold in U.S.A.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, includ- ing interference that may cause unde- sired operation.

the

tire pressure monitoring When system warning light is lit, one or more of your tires is significantly un- der−inflated. You should stop and check your tires as soon as possible, and inflate them to the proper pres- sure as indicated on the vehicle’s tire information placard. Driving on a sig- nificantly under−inflated tire causes the tire to overheat and can lead to tire failure. Under−inflation also re- duces fuel efficiency and tire tread life, and may affect the vehicle’s han- dling and stopping ability. Each tire, including should be checked monthly when cold and set to the recommended inflation pres- sure as specified in the vehicle plac- ard and owner’s manual.

spare,

the

interference

NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protec- tion against harmful in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruc- tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interfer- ence television reception, which can be determined by turning the equipment off and on, the user is en- couraged to try to correct the interfer- ence by one or more of the following measures:

to radio or

191

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

D Reorient or relocate the receiving an-

tenna.

D Increase the separation between the

equipment and receiver.

D Connect the equipment into an outlet to

on a circuit different which the receiver is connected.

from

that

D Consult the dealer or an experienced

radio/TV technician for help.

FCC WARNING: Changes or modifications not ex- pressly approved by the party respon- sible for compliance could void the user’s authority to operate the equip- ment.

For vehicles sold in Canada

Operation is subject to the following two conditions: (1) this device may not cause interfer- ence, and (2) this device must accept any interference that may cause undesired operation of the device.

interference,

including

192

’05 4Runner_U (L/O 0409)

—Replacing tires and wheels When replacing the wheels, be sure to install air pressure sensors on the wheels. There are 3 ways to set up the air pres- sure sensors: a. Remove the sensor from the old wheel

and install it to the new wheel.

b. Keep the same wheel with air pressure

sensor and replace only the tire.

c. Use a new wheel and sensor. In this case, you have to register an ID code for a new sensor.

CAUTION

Have the tires, wheels or sensors re- placed and ID codes registered by a Toyota dealer. If you need sensors, purchase from a Toyota dealer.

Parking brake

When parking, firmly apply the parking brake to avoid inadvertent creeping. To set: Fully depress the parking brake pedal. For better holding power, first de- press the brake pedal and hold it while setting the parking brake. To release: Depress pedal once again. To remind you that the parking brake is set, the parking brake reminder light in the instrument panel remains on until you release the parking brake.

the parking brake

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

CAUTION

Before driving, be sure the parking brake is fully released and the park- ing brake reminder light is off.

Cruise control The cruise control allows you to cruise the vehicle at a desired speed over 40
km/h (25 mph) even with your foot off the accelerator pedal. Your cruising speed can be maintained up or down grades within the limits of engine performance, although a slight speed change may occur when driving up or down the grades. On steeper hills, a greater speed change will occur so it is better to drive without the cruise control.

CAUTION

D To help maintain maximum control of your vehicle, do not use the cruise control when driving in heavy or varying traffic, or on slip- pery (rainy, icy or snow−covered) or winding roads.

If

D Avoid vehicle speed increases when driving downhill. the vehicle speed is too fast in relation to the cruise control set speed, cancel the cruise control then downshift the transmission to use engine braking to slow down.

TURNING THE SYSTEM ON To operate the cruise control, press the “ON−OFF” button. This turns the system on. The indicator light in the instrument panel shows that you can now set the vehicle at a desired cruising speed. Anoth- er press will turn the system completely off.

CAUTION

To avoid accidental cruise control en- gagement, keep the “ON−OFF” button off when not using the cruise control.

193

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

If you need acceleration—for example, when passing—depress the accelerator pedal enough for the vehicle to exceed the set speed. When you release it, the vehicle will return to the speed set prior to the acceleration. CANCELLING THE PRESET SPEED You can cancel the preset speed by: a. Pulling the lever in the “CANCEL” di-

rection and releasing it.

b. Depressing the brake pedal. c. Pushing the “ON−OFF” button. If the vehicle speed falls below about 40
km/h (25 mph), the preset speed will auto- matically cancel out. If the vehicle speed drops 16 km/h (10
mph) below the preset speed, the preset speed will also automatically cancel out. If the preset speed automatically cancels out other than for the above cases, have your vehicle checked by your Toyota deal- er at the earliest opportunity.

RESETTING TO A FASTER SPEED Push the lever up in the “+ RES” direction and hold it. Release the lever when the desired speed is attained. While the lever is held up, the vehicle will gradually gain speed. However, a faster way to reset is to ac- celerate the vehicle and then push the lever down in the “− SET” direction. RESETTING TO A SLOWER SPEED Push the lever down in the “− SET” direc- tion and hold it. Release the lever when the desired speed is attained. While the lever is held down, the vehicle speed will gradually decrease. However, a faster way to reset is to de- press the brake pedal and then push the lever down in the “− SET” direction. Even if you downshift from “D” to “4”, with the cruise control on, engine braking will not be enabled because the cruise control is not cancelled. To decrease the vehicle speed, reset to a slower speed with the cruise control lever or depress the brake pedal. If you use the brake pedal, cruise control is cancelled.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

SETTING AT A DESIRED SPEED The transmission must be in “D” before you set the cruise control speed. Bring your vehicle to the desired speed, push the lever down in the “− SET” direc- tion and release it. This sets the vehicle at that speed. If the speed is not satisfac- tory, tap the lever up for a faster speed, or tap it down for a slower speed. Each tap changes the set speed by 1.6 km/h (1.0 mph). You can now take your foot off the accelerator pedal.

194

’05 4Runner_U (L/O 0409)

lever or by depressing

RESUMING THE PRESET SPEED If the preset speed is cancelled by pulling the control the brake pedal, pushing the lever up in the “+ RES” direction will restore the speed set prior to cancellation. 2UZ−FE engine only— However, once the vehicle speed falls be- low about 40 km/h (25 mph), the preset speed will not be resumed. CRUISE CONTROL FAILURE WARNING If the instrument cluster flashes when using the cruise control, press the “ON−OFF” button to turn the system off and then press it again to turn it on. If any of the following conditions then oc- curs, there is some trouble in the cruise control system. D The indicator light does not come on. D The indicator light flashes again. D The

light goes out after

“CRUISE”

indicator

indicator

light

the

in

it

comes on.

If this is the case, contact your Toyota dealer and have your vehicle inspected.

195

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

196

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

SECTION 1− 8

OPERATION OF INSTRUMENTS AND CONTROLS Audio system Reference Using your audio system Audio remote controls Rear seat audio system Audio system operating hints

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

198
198
215
217
225

For vehicle equipped with Navigation system, please refer to the separate “Navigation System Owner’s Manual”.

197

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

Reference

Type 1: AM·FM radio/cassette player/com- pact disc player (with compact disc changer controller)

Type 2: AM·FM radio/cassette player/com- pact disc player with changer

“FM”,

“AM”,

“TAPE”,

Using your audio system— —Some basics This section describes some of the basic features on Toyota audio systems. Some information may not pertain to your sys- tem. Your audio system works when the ignition key is in the “ACC” or “ON” position. TURNING THE SYSTEM ON AND OFF Push “PWR·VOL” to turn the audio system on and off. Push “DISC” or “LOAD” to turn on that function without pushing “PWR·VOL”. To turn on the cas- sette or compact disc player, a cassette or compact disc must be loaded in the player. You can turn on each player by inserting a cassette tape or compact disc. You can turn off each player by ejecting the cassette tape or compact disc. If the audio system was previously off, then the entire audio system will be turned off when you eject the cassette tape or com- pact disc. If the another function was pre- viously playing, it will come on again. SWITCHING BETWEEN FUNCTIONS Push “DISC” or “LOAD” if the system is already on but you want to switch from one function to another.

“TAPE”,

“AM”,

“FM”,

198

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

TONE AND BALANCE For details about your system’s tone and balance controls, see the description of your own system. Tone How good an audio program sounds to you is largely determined by the mix of the treble, midrange and bass levels. In fact, different kinds of music and vocal programs usually sound better with differ- ent mixes of treble, midrange and bass. Balance A good balance of the left and right stereo channels and of the front and rear sound levels is also important. Keep in mind that if you are listening to a stereo recording or broadcast, changing the right/left balance will increase the vol- ume of one group of sounds while de- creasing the volume of another.

YOUR RADIO ANTENNA Your vehicle has an antenna printed on the inside of the rear quarter window.

NOTICE

Attaching the film (especially conduc- tive or metallic the rear quarter glass will noticeably reduce the sensitivity of the radio.

type) on

YOUR CASSETTE PLAYER When you insert a cassette, the exposed tape should face to the right.

NOTICE

Do not oil any part of the player and do not insert anything other than cas- sette tapes into the slot, or the tape player may be damaged.

YOUR COMPACT DISC PLAYER (type 1) When you insert a disc, gently push it in with the label side up. (The player will automatically eject a disc if the label side is down.) The player will play from track 1 through the end of the disc. Then it will play from track 1 again.

NOTICE

Never try to disassemble or oil any part of the compact disc player. Do not insert anything other than com- pact discs into the slot.

The player is intended for use with 12 cm (4.7 in.) discs only.

199

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

YOUR COMPACT DISC PLAYER WITH CHANGER (type 2) When you insert a disc, push the “LOAD” button and gently push the disc in with the label side up. (The player will auto- matically eject a disc if the label side is down.) This compact disc player can store up to six discs. The player will play from track 1 through the end of the disc. Then it will play from track 1 of the next disc. The player is intended for use with 12 cm (4.7 in.) discs only.

NOTICE

z Do not stack up two discs for in- sertion, or it will cause damage to the compact disc player. Insert only one compact disc into slot at a time.

z Never try to disassemble or oil any part of the compact disc player. Do not insert anything except a com- pact disc into the slot.

200

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

—Controls and features "Type 1

Details of specific buttons, controls and features are described in the alphabetical list that follows.

201

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK/TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The button num- ber will appear on the display. To recall a preset station: Push the button for the station you want. The button num- ber and station frequency will appear on the display. These systems can store one AM and two FM stations for each button. (The display will show “AM”, “FM1” or “FM2” when you push “AM” or “FM” button.)

(Eject button) the cassette

Push tape eject button to eject a cassette. Push the compact disc eject button to eject a compact disc.

202

’05 4Runner_U (L/O 0409)

(Program)

Compact disc player

” indicates the top side, “

Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates the bottom side). Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

(Reverse/Fast forward button)

Cassette player

Push “ ” (preset button 6) to fast for- ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto−reverse feature.

” (preset button 6) or Push and hold “ “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) By using the “AUDIO CONTROL” knob, you can adjust the tone and sound bal- ance. On some models, you can also turn on or off the surround function. Each time you push this knob, the mode changes. To adjust the tone and balance and turn on or off the surround function, turn the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID: Adjusts mid−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

ON”

“SURROUND

FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. SURROUND: Turn on or off the surround function. or “SURROUND OFF” will appear on the display. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it.

incorrectly

inserted

’05 4Runner_U (L/O 0409)

“NO DISC”: The compact disc changer of separate unit is empty. Insert a disc. “ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. Ɲ DISC Ɯ With compact disc changer only— Use these buttons to select the disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push “ ” will appear on the display. Push the button again to turn off Dolbyr B NR.

” (preset button 3). “

B NR∗

The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM Push the “FM” button to turn on the radio and select the FM band. “FM1” or “FM2” will appear on the display. This system allows you to set twelve FM stations, two for each of the preset button. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order.

in random order, or

203

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

the

track

Compact disc player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again. With compact disc changer only— Repeating a disc: Push and hold “RPT” (preset button 2) until you hear a beep. “ ” will ap- pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again.

To play the tracks on one disc in random order: Quickly push and release “RAND” (preset button 1). “ ” will appear on the display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. With compact disc changer only— To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again. RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. 204

feature, push

the repeat

random

SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold the “SCAN” button until you hear a beep. The radio will tune in the next preset station up the band, stay there for 5 seconds, and then move to the next preset station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release the “SCAN” but- ton. The radio will find the next station up the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

listening

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release the “SCAN” but- ton. “SCAN” will appear on the display and the player will scan all the tracks on the disc you are to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. With compact disc changer only— Scanning the first tracks of all the discs in the magazine: Push the “SCAN” button until you hear a ·SCAN” will appear on the dis- beep. “ play and the player will scan the first track of the next disc. To stop scanning, push this button again. If the player has scanned all the discs, it will stop scan- ning.

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “Ɯ” or “Ɲ” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When the beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.

Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “Ɯ” or “Ɲ” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.

205

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

to

to

title,

track

then back

TEXT This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

206

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

"Type 2

Details of specific buttons, controls and features are described in the alphabetical list that follows.

207

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

(See

to preset and

1 2 3 4 5 6 (Preset buttons) These buttons are used tune in radio stations. To preset a station to a button: Tune in the desired station. “TUNE” or “SEEK/TRACK”.) Push and hold down the button until you hear a beep—this will set the station to the button. The preset but- ton number will appear on the display. RDS stations will be preset to the buttons when you turn on the RDS. (See “RDS” button.) To recall a preset station: Push the button for the station you want. The preset but- ton number and station frequency will ap- pear on the display. This radio can store one AM, two FM and RDS stations for each button. (The display will show “FM TYPE” when you push “AM” or “FM” but- ton.)

“FM2” or

“FM1”,

“AM”,

208

’05 4Runner_U (L/O 0409)

(Eject button)

(Program)

Cassette player This button is used to eject a cassette. Compact disc player This button is used to eject one or all compact discs. To eject the current compact disc, push and release the compact disc eject button. To eject a specific disc, push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to eject is displayed. Push and release the eject but- ton. To eject all discs at a time, press and hold the eject button until you hear a beep. The last compact disc played before pushing the button will be ejected first. If the ejected disc is not removed for a long time, the eject function will be cancelled.

” indicates the top side, “

Push “ ” (preset button 4) to select the other side of a cassette tape. The display indicates which side is currently selected (“ ” indicates the bottom side). Auto−reverse the cassette player reaches the end of a tape side, it automatically reverses and begins to play the other side. This is true whether the cassette was playing or fast forwarding.

feature: After

(Reverse/Fast forward button)

Cassette player

Push “ ” (preset button 6) to fast for- ward a cassette tape. “FF” will appear on the display. Push “ ” (preset button 5) to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ” or “TAPE” button. To stop ing, push “ the tape while it is rewinding, push “ ” or “TAPE” button. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto−reverse feature.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

Compact disc player

” (preset button 6) or Push and hold “ “ ” (preset button 5) to fast forward or reverse within a compact disc. When you release the button, the compact disc play- er will resume playing. AM Push the “AM” button to turn on the radio and select the AM band. “AM” will appear on the display. AUDIO CONTROL (Tone and sound bal- ance adjustment function) By using the “AUDIO CONTROL” knob, you can adjust the tone and sound bal- ance, and the surround function. Each time you push this knob, the mode changes. To adjust the tone and balance and turn on or off the surround function, turn the knob. BAS: Adjusts low−pitched tones. The dis- play ranges from −5 to 5. MID: Adjusts mid−pitched tones. The dis- play ranges from −5 to 5. TRE: Adjusts high−pitched tones. The dis- play ranges from −5 to 5.

turn on or off

“SURROUND ON” or

FAD: Adjusts the sound balance between the front and rear speakers. The display ranges from F7 to R7. BAL: Adjusts the sound balance between the right and left speakers. The display ranges from L7 to R7. SURROUND: Turn on or off the surround function. “SUR- ROUND OFF” will appear on the display. DISC (Compact disc) Push the “DISC” button to play a compact disc. When the audio system is set into com- pact disc operation, the display shows the track, or track and disc number currently being played. Error messages If the player malfunctions, your audio sys- tem will display one of the six following error messages. “WAIT”: The compact disc player unit may be too hot. Allow the player to cool down. “ERROR 1”: The disc may be dirty, dam- aged or (up−side down). Clean the disc and re−insert it. “NO DISC”: The compact disc changer of separate unit is empty. Insert a disc.

incorrectly

inserted

“ERROR 3”: There is a problem inside the system. Eject the disc or magazine. Set the disc or magazine again. “ERROR 4”: Over−current. Ask your Toyota dealer to inspect. “CD OPEN”: The compact disc changer lid of separate unit is open. Close the compact disc changer lid. If the malfunction still exists, take your vehicle to your Toyota dealer. Ɲ DISC Ɯ Use these buttons to select a disc you want to listen to. Push “Ɲ” (preset button 3) or “Ɯ” (preset button 4) until the number of the disc you want to listen appears on the display. Dolbyr If you are listening to a tape that was recorded with Dolbyr B Noise Reduction, push “ ” will appear on the display. Push the button again to turn off Dolbyr B NR.

” (preset button 3). “

B NR∗

209

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

The Dolby NR mode reduces tape noise by about 10 dB. For best sound reproduc- tion, play your tapes with this button on or off according to the mode used to re- cord the tape. ∗ : Dolby noise reduction manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double D symbol are trademarks of Dolby Laboratories Licensing Corporation. FM Push the “FM” button to turn on the radio and select the FM band. “FM1”, “FM2” or “FM TYPE” will appear on the display. This system allows you to set twelve FM and six RDS stations, three for each of the preset button. If the RDS is off or RDS stations are not preset to the preset buttons, “FM TYPE” will not appear on the display. LOAD This button is used to load the compact discs the compact disc player. This player can store up to six discs. To load one compact disc only, quickly push and release the button, then insert a compact disc. After the disc is loaded, the shutter of the slot will close. If no compact disc is inserted, the shutter will close after 15 seconds.

in

210

To load multiple compact discs, push and hold the button (until you hear a beep when the audio system is on), then insert the first compact disc. After the disc is loaded, the shutter of the slot will close. After a few seconds, the shutter will auto- matically open again so the next disc can be inserted. The same process can be applied for loading the rest of the discs. If the player is full of discs, “DISC FULL” will appear on the display. If no compact disc is inserted, the shutter will close after 15 seconds. PWR·VOL (Power and Volume) Push “PWR·VOL” to turn the audio system on and off. Turn “PWR·VOL” to adjust the volume. RDS (Radio Data System) Your audio system is equipped with Radio Data System (RDS). RDS station providing good reception is automatically selected if current reception worsens. The “RDS” button turns the RDS on and off. This button is operational except in AM mode.

turns on,

the radio starts

To turn on the RDS, push and hold this button until you hear a beep and “RDS” will appear on the display. At this time, the radio starts to search the RDS sta- tions and “RDS SEARCH” will flash on the display. Quickly push and release this button when the RDS to search “RDS the RDS stations and SEARCH” will flash on the display. When found, stations are “FOUND” and the number of the RDS sta- tions will appear on the display, and you will hear two beeps. The stations will be preset to the preset buttons. If the RDS stations can not be found, “NO RDS ST” will appear on the display and you will hear a beep, and the display returns to the previous mode. To turn the RDS off, push the button until you hear a beep again.

the RDS

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

in random order, or

RAND (Random) There are two random features—you can either listen to the tracks on one compact to disc the listen tracks on all the compact discs in the magazine in random order. To play the tracks on one disc in random order: Quickly push and release “RAND” (preset ” will appear on the button 1). “ display and the player will perform the tracks on the disc you are listening to in random order. To turn off the random fea- ture, push this button again. To play all the tracks in the magazine in random order: Push and hold “RAND” (preset button 1) ” will ap- until you hear a beep. “ pear on the display and the player will perform all the tracks on all the discs in the magazine in random order. To turn off the this button again.

feature, push

random

the repeat

RPT (Repeat) Cassette player Push “RPT” (preset button 2) while the ” will appear on track is playing. “ the display. When the track ends, it will automatically rewind and replay. To turn off feature, push this button again. There must be at least 3 seconds of blank space between tracks in order for the re- peat feature to work correctly. Compact disc player There are two repeat features—You can either replay a disc track or a whole com- pact disc. Repeating a track: Quickly push and release “RPT” (preset button 2) while is playing. ” will appear on the display. When “ the track ends, it will automatically replay. To turn off the repeat feature, push this button again.

track

the

Repeating a disc: Push and hold “RPT” (preset button 2) ” will ap- until you hear a beep. “ pear on the display. The player will repeat all the tracks on the disc you are listening to. When the disc ends, the player will automatically go back to the first track on the disc and replay. To turn off the repeat feature, push this button again. SCAN Radio You can either scan all the frequencies on a band or scan only the preset stations for that band. To scan the preset stations: Push and hold “Ɯ” or “Ɲ” side of the “SCAN” button until you hear a beep. The radio will tune in the next preset station up or down the band, stay there for 5
seconds, and then move to the next pre- set station. To stop scanning, push this button again. To scan all the frequencies: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. The radio will find the next station up or down the station band, stay there for 5 seconds, and then scan again to the next station. To stop scanning, push this button again.

211

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

Compact disc player There are two scan features—you can ei- ther scan the tracks on a specific disc or scan the first tracks of all the discs in the magazine. Scanning the tracks on a disc: Quickly push and release “Ɯ” or “Ɲ” side of the “SCAN” button. “SCAN” will appear on the display and the player will scan up or down all the tracks on the disc you are listening to. To stop scanning, push this button again. If the player scanned all the tracks on the disc, it will stop scanning. Scanning the first tracks of all the discs in the magazine: Push “Ɯ” or “Ɲ” side of the “SCAN” but- ·SCAN” will ton until you hear a beep. “ appear on the display and the player will scan up or down the first track of the next disc. To stop scanning, push this button again. the auto changer has scanned all the discs, it will stop scan- ning.

If

212

the seek mode,

the radio finds and the next station up or down the

SEEK/TRACK (Seeking/Track up/down) Radio In plays station band. To seek the next station, quickly push and release “Ɯ” or “Ɲ” side of the “SEEK/ TRACK” button. Do this again to find the station after that. Cassette Player Use this button to skip up or down to locate a song or recording. You can select up to nine recordings (in- cluding current one). A blank space of at least 3 seconds is considered to be a start of a recording. When the beginning of a tape is reached, the player automatically resumes play. When the end of the tape is reached, the player automatically reverses sides and resumes normal play. In addition, the feature may not work well with some spoken word, live, or classical recordings.

Compact disc player Use this button to skip up or down to a different track. the “SEEK/ Push “Ɯ” or “Ɲ” side of TRACK” button until the number of the track you want to listen to appears on the display. If you want to return to the begin- ning of the current track, quickly push the down side of the button one time. ST (Stereo reception) display Your radio automatically changes to stereo reception when a stereo broadcast is re- ceived. “ST” appears on the display. If the signal becomes weak, the radio reduces the amount of channel separation to prev- ent the weak signal from creating noise. If the signal becomes extremely weak, the radio switches from stereo to mono recep- tion. TAPE Push the “TAPE” button to play a cassette tape.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

in RDS

is operational only

TEXT Radio This button mode. When an RDS radio station transmits a text message, “TEXT” will be displayed. At this time, push the “TEXT” button to view the text message. The message display will be canceled if any button that affects the display is pushed. To view the mes- sage again, push this button again. After the entire message has been displayed, the message will disappear. The RDS audio system has memory to store three 64−character messages. To store a message in memory, push and hold the “TEXT” button until you hear a beep. If three messages are already stored in memory, the oldest message will be over- written by the new message. To recall a radio text message, push the “TEXT” button momentarily. This will dis- play the most recent message. Each push of the button will display messages in the order of most to least recent.

If no messages have been stored, or if there are no more messages to be re- called, “NO MESSAGE” will appear on the display, and the message display will be canceled. The message display will be canceled if you activate any function that affects the display. Compact disc player This button is used to change the display for the compact disc that contains text data. To change the display, quickly push and release the “TEXT” button while the com- pact disc is playing. The display changes in the order from the elapsed time to disc title the elapsed time. If this button is pushed while a compact disc that does not contain text data is playing, “NO TITLE” will appear on the display. If the entire disc or track title does not appear on the display, push and hold the button until you hear a beep. The rest of the title will appear.

then back

track

title,

to

to

the

“TRAF” button,

TRAF (Traffic) This button turns the traffic announcement (TA) feature on and off. This button is operational only in FM mode. By pushing “TRAF SEEK” will flash on the display and the radio will start seeking any traffic program station. When a traffic program station is found, “TRAF” will be displayed and you will hear a beep. After the traffic announcement program is over, the display returns to the previous mode. If no traffic program station is found, “NO TRAF INFO” appears on the display for a few seconds and the display returns to the previous mode. To cancel the traffic announcement, push this button again. TUNE (Tuning) Turn the “TUNE” knob clockwise to step up the frequency. Turn the knob counter- clockwise to step down the frequency.

213

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

TYPE (Program Types) When you push the “TYPE” button while receiving an RDS station, the current pro- gram type appears on the display. Each time you push this button, the pro- gram type changes as in the following: D ROCK D EASY LIS (Easy listening) D CLS/JAZZ (Classical music and Jazz) D R&B (Rhythm and Blues) D INFORM (Information) D RELIGION D MISC (Miscellaneous) D ALERT (Emergency message)

214

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

Audio remote controls (steering switches)

’05 4Runner_U (L/O 0409)

Some parts of the audio system can be adjusted using the switches on the steer- ing wheel. Details of the specific switches, controls, and features are described below. 1. Volume control switch 2. “ƜƝ” switch 3. “MODE” switch

215

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

to

increase while

1. Volume control switch Push “+” to increase the volume. The vol- ume continues the switch is being pushed. Push “−” the volume. The to decrease volume continues to decrease while the switch is being pushed. 2. “ƜƝ” switch Radio This switch has the following features— To select a preset station: Quickly push and release the “Ɯ” or “Ɲ” side of the switch. Do this again to select the next preset station. To seek a station: Push and hold the “Ɯ” or “Ɲ” side of the switch until you hear a beep. Do this again to find the next station. If you push the switch on either side during the seek mode, seeking will be cancelled. Cassette player This switch has the following features— To skip to a different track in either direc- tion: Quickly push and release the “Ɯ” or “Ɲ” side of the switch. “FF 1” or “REW 1” will appear on the display.

216

Next, push either side of the track switch until the track you want to listen to is set. If you push the switch ten times, the skip function will turn off. (You can skip up to nine tracks at a time.) When counting the number of the tracks you want to rewind, remember to count the current track as well. For example, if you want to rewind to a song that is two tracks before the song you are listening to, push the “Ɲ” side of the switch three times. If you push the track switch further than you wanted to, push the other side of the switch. The in- creased or reduced. The track number you select is not valid if the tracks remaining on the current side of the cassette. D When the tape reaches to the begin- ning, the player will automatically start playing that side.

track number will be

the number of

is higher

than

it

D After the tape reaches to the end, the reverse and

player will automatically start playing the other side.

There must be at least 3 seconds of blank space between tracks for the track switch to work correctly. In addition, the feature may not work well with some spoken, live, or classical recordings. To fast forward or reverse: Push and hold the “Ɯ” side of the switch to fast forward a cassette tape. “FF” will appear on the display. Push and hold the “Ɲ” side of the switch to rewind a tape. “REW” will appear on the display. To stop the tape while it is fast forward- ing, push the “Ɯ” side of the switch. To stop the tape while it is rewinding, push the “Ɲ” side of the switch. If a tape rewinds completely, the cassette player will stop and then play that same side. If a tape fast forwards completely, the cassette will play the other side of the tape using the auto−reverse feature. Compact disc player Use this switch to skip up or down to a different track in either direction. Quickly push and release the “Ɯ” or “Ɲ” side of the switch until the track you want to listen to is set. If you want to return to the beginning of the current track, push the “Ɲ” side of the switch once, quickly.

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

With compact disc changer only— Push and hold the “Ɯ” or “Ɲ” side of the switch until the disc you want to listen to is set. 3. “MODE” switch Push “MODE” switch to select an audio mode. Each push changes the mode se- quentially if the desired mode is ready to use. To turn the audio system on, push the “MODE” switch. To turn the audio system off, push and hold the “MODE” switch until the system turns off.

’05 4Runner_U (L/O 0409)

if

the

front audio system

Rear seat audio system— The rear seat audio system is designed for the rear seat passengers to enjoy the audio sound separately between the front seats and rear seats. The rear seat audio system can be turned on with the rear audio system controller even is off. When the front audio is turned off, the rear audio system will be turned off simul- taneously. The rear passengers can enjoy all the modes (AM and FM radio, cassette tape player, compact disc player and compact disc player with changer) with the rear seat audio system when a cassette tape and discs are loaded in the front audio system. When the same mode is selected on the front and rear audio systems at the same time, the system can be operated on the front audio system. If the radio mode is selected on the front and rear audio systems at the same time, AM and FM modes cannot be changed on the rear seat audio system. You can enjoy the rear seat audio system with a special headphone. For details, re- fer to the manufacturer’s instructions.

The wireless headphone can be used with- in a radius of approximately 7 m (23 ft.) from the rear seat audio system. If the signal becomes weak, the headphone will mute. You can purchase a wireless headphone at a Toyota dealer.

CAUTION

Do not drive with using the head- phone. Otherwise, you may be hard to hear the sound from the outside while using the headphone and may cause an accident.

217

2005 4RUNNER from Sep. ’04 Prod. (OM35843U)

’05 4Runner_U (L/O 0409)

The rear seat audio system consists of following components. 1. Front audio system 2. Rear seat audio system display