2000 Toyota 4runner Owners Manual

the side seatbelts and center of seatbelt and arranged them in their proper position and are ready to use.

Front

Rear

40

2000 4Runner (OM35762U)

For your safety and comfort, adjust the head restraint before driving. To raise: Pull it up. To lower: Push it down while pressing the lock release button. On some models, you can also move the head If such adjustment is desired, pull or push the head restraint. The head restraint is most effective when it is close to your head. Therefore, using a cushion on the seatback is not recom- mended.

forward or backward.

restraint

CAUTION

(cid:1) Adjust the center of the head re- straint so that it is closet to the top of your ears.

(cid:1) After adjusting the head restraint, make sure it is locked in position. the head re-

(cid:1) Do not drive with

straints removed.

Seat belts— —Seat belt precautions Toyota strongly urges that the driver and passengers in the vehicle be properly re- strained at all times with the seat belts provided. Failure to do so could increase the chance of injury and/or the severity of injury in accidents. Child. Use a child restraint system ap- propriate for the child until the child be- comes large enough to properly wear the vehicle’s seat belts. See “Child restraint” for details. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. If a child must sit in the front seat, the seat belts should be worn properly. If an accident occurs and the seat belts are not worn properly, the force of the rapid infla- tion of the airbag may cause death or serious injury to the child.

lap.

Do not allow the child to stand up or kneel on either rear or front seats. An unrestrained child could suffer serious in- jury or death during emergency braking or a collision. Also do not let the child sit on your It does not provide sufficient restraint. Pregnant woman. Toyota recommends the use of a seat belt. Ask your doctor for specific lap belt should be worn securely and as low as possible over the hips and not on the waist. Injured person. Toyota recommends the use of a seat belt. Depending on the inju- ry, first check with your doctor for specific recommendation.

recommendations. The

2000 4Runner (OM35762U)

41

(cid:1) Keep the belts clean and dry.

If they need cleaning, use a mild soap solution or lukewarm water. Never use bleach, dye, or abrasive clean- ers—they may severely weaken the belts. (See “Cleaning the interior” in Section 5.)

(cid:1) Replace the belt assembly (includ- ing bolts) if it has been used in a severe impact. The entire assembly should be replaced even if damage is not obvious.

CAUTION

the vehicle

in their seats Persons should ride their seat belts properly wearing whenever is moving. Otherwise, they are much more likely to suffer serious bodily injury or death in the event of sudden braking or a collision. When using the seat belts, observe the following: (cid:1) Use the belt for only one person at a time. Do not use a single belt for two or more people—even children. (cid:1) Avoid reclining the seatbacks too much. The seat belts provide maxi- mum protection when the seatbacks are in the upright position. (Refer to the seat adjustment instructions.) (cid:1) Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seat or side doors.

(cid:1) Inspect the belt system periodically. Check for cuts, fraying, and loose parts. Damaged parts should be re- placed. Do not disassemble or modify the system.

42

2000 4Runner (OM35762U)

—Front and rear outside seat belts

Adjust the seat as needed (front seats only) and sit up straight and well back in the seat. To fasten your belt, pull it out of the retractor and insert the tab into the buckle. You will hear a click when the tab locks into the buckle. The seat belt length automatically adjusts to your size and the seat position. The retractor will lock the belt during a sudden stop or on impact. It also may lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend, and you can move around freely.

If the seat belt cannot be pulled out of the retractor, firmly pull the belt and release it. You will then be able to smoothly pull the belt out of the retractor. When a passenger’s shoulder belt is com- pletely extended and retracted even slightly, the belt is locked in that position and cannot be extended. This fea- ture is used to hold the child restraint system securely. (For details, see “Child restraint” in this section.) To free the belt again, fully retract the belt and then pull the belt out once more.

then

is

CAUTION

Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause serious injuries in a collision.

Seat belts with an adjustable shoulder anchor— Adjust the shoulder anchor position to your size. To raise: Slide the anchor up. To lower: Push in the lock release button and slide the anchor down. After adjustment make sure the anchor is locked in position.

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

2000 4Runner (OM35762U)

43

Take up slack

Too high

CAUTION

lap

(cid:1) High- positioned

belts

and loose- fitting belts both could cause serious injuries due to sliding un- der the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

Keep as low on hips as possible

(cid:1) For your safety, do not place the

shoulder belt under your arm.

the

lap and

the position of

Adjust shoulder belts. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit by pulling the shoulder portion upward through the latch plate.

To release the belt, press the buckle- re- lease button and allow the belt to re- tract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains untwisted as it re- tracts.

44

2000 4Runner (OM35762U)

—Rear center seat belt

Lengthen

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

Sit up straight and well back in the seat. To fasten your belt, insert the tab into the buckle. You will hear a click when the tab locks into the buckle. If the belt is not long enough for you, hold the tab at a right angle to the belt and pull on the tab.

Too high

Adjust to a snug fit

Keep as low on hips as possible

Remove excess length of the belt and adjust the belt position. To shorten the belt, pull the free end of the belt. Position the lap belt as low as possible on your hips—not on your waist, then ad- just it to a snug fit.

CAUTION

High- positioned and loose- fitting lap belts could cause serious injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

2000 4Runner (OM35762U)

45

—Stowing rear seat belt and buckles

from your Toyota dealer

—Seat belt extender If your seat belt cannot be fastened se- curely because it is not long enough, a personalized seat belt extender is avail- able free of charge. Please contact your local Toyota dealer so that the dealer can order the proper re- quired length for the extender. Bring the heaviest coat you expect to wear for prop- er measurement and selection of length. Additional ordering information is available at your Toyota dealer.

To release the belt, press the buckle- re- lease button.

The rear seat belt and buckles can be stowed when not in use. Seat belt and buckles must be stowed before you fold the seat back. (See “Fold down rear seats” in this section.)

46

2000 4Runner (OM35762U)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the seat belt extender is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function normally, immediately contact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.

CAUTION

When using the seat belt extender, observe the following. Failure to fol- low these instructions could result in less effectiveness of the seat belt re- straint system in case of vehicle acci- dent, increasing the chance of per- sonal injury. (cid:1) Never use the seat belt extender if you can fasten the seat belt without it.

(cid:1) Remember that the extender pro- vided for you may not be safe when used on a different vehicle, or for another person or at a different seating position than the one origi- nally intended for.

To connect the extender to the seat belt, insert the tab into the seat belt buckle so that the “PRESS” signs on the buckle- release buttons of the ex- tender and the seat belt are both facing outward as shown. You will hear a click when the tab locks into the buckle. When releasing the seat belt, press on the buckle- release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and extend- er itself. When not and store in the vehicle for future use.

in use, remove the extender

2000 4Runner (OM35762U)

47

—Front seat belt pretensioners

The driver and front passenger’s seat belt pretensioners are designed to be activated in response to a severe fron- tal impact. When the airbag sensor detects the shock of a severe frontal impact, the front seat belt is quickly drawn back in by the re- tractor so that the belt snugly restrains the front seat occupants. The seat belt pretensioners are activated even with no passenger in the front seat. Collisions occurring at certain speeds and angles may cause the seat belt preten- sioners and SRS airbags not to operate all together.

This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the front seat belt pretensioners are operating proper- ly. This warning the airbag sensor assembly, front airbag sen- sors, seat belt pretensioner assemblies, warning interconnecting wiring and power sources. (For details, see “Service reminder indicators and warning buzzers” in Section 1- 5.)

light system monitors

light,

The seat belt pretensioner system mainly consists of the following components and their locations are shown in the illustra- tion. 1. Front airbag sensors 2. SRS warning light 3. Seat belt pretensioner assemblies 4. Airbag sensor assembly The seat belt pretensioner is controlled by the airbag sensor assembly. The airbag sensor assembly consists of a safing sen- sor and airbag sensor.

48

2000 4Runner (OM35762U)

When a seat belt pretensioner is acti- vated, an operating noise may be heard and a small amount of smoke- like gas may be released. This gas is harmless and does not indicate that a fire is occur- ring. Once the seat belt pretensioner has been activated, the seat belt retractor remains locked.

CAUTION

Do not modify, remove, strike or open the front seat belt pretensioner as- semblies, airbag sensor or surround- ing area or wiring. Doing any of these may cause sudden operation of the front seat belt pretensioners or disable the system, which could re- sult in serious injury. Failure to follow these can result in serious injuries.

instructions

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the seat belt pretensioners in some cases. (cid:1) Installation of electronic devices such as a mobile two-way radio, cassette tape player or compact disc player

(cid:1) Repairs on or near the front seat

belt retractor assemblies

(cid:1) Modification of the suspension sys-

tem

(cid:1) Modification of the front end struc-

ture

(cid:1) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

(cid:1) Repairs made on or near the front fenders, front end structure or con- sole

the

following conditions occurs,

This front seat belt pretensioner system has a service reminder indicator to inform the driver of operating problems. If either of this indicates a malfunction of the airbags or pretensioners. Contact your Toyota dealer as soon as possible the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on. (cid:1) The light comes on or flashes while

to service

driving.

(cid:1) If either front seat belt does not retract or can not be pulled out due to a malfunction or activation of the preten- sioner.

49

2000 4Runner (OM35762U)

SRS driver and front passenger airbags

(cid:1) The front seat belt pretensioner assem- bly or surrounding area has been dam- aged.

(cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause to operate.

the seat belt pretensioners

(cid:1) The front seat belt pretensioner assem- bly is scratched, cracked, or otherwise damaged.

The SRS (Supplemental Restraint Sys- tem) airbags are designed to provide further protection for the driver and front passenger in addition to the pri- mary safety protection provided by the seat belts. In response to a severe frontal impact, the SRS airbags work together with the seat belts to help reduce injury by inflat- ing. The SRS airbags help to reduce inju- ries mainly to the driver’s or front passen- ger’s head or chest directly hitting the steering wheel or dashboard. The passen- ger airbag is activated even with no pas- senger in the front seat. Be sure to wear your seat belt.

50

2000 4Runner (OM35762U)

CAUTION

A driver or front passenger too close to the steering wheel or dashboard during airbag deployment can be killed or seriously injured. Toyota strongly recommends that: (cid:1) The driver sit as far back as pos- sible from the steering wheel while still maintaining control of the ve- hicle.

(cid:1) The front passenger sit as far back

as possible from the dashboard.

(cid:1) All vehicle occupants be properly restrained using the available seat belts.

This indicator comes on when the igni- tion key is turned to the “ACC” or “ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. This warning the airbag sensor assembly, front airbag sen- sors, inflators, warning light, interconnect- ing wiring and power sources. (For details, see indicators and warning buzzers” in Section 1- 5.)

light system monitors

reminder

“Service

this

However, threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle or sign pole, which can move or deform on impact, or if it is involved in an underride collision (e.g. a collision in which the nose of the vehicle “underrides”, or goes under, the bed of a truck, etc.). It is possible that in some collisions at the lower zone of airbag sensor detection and activation the SRS airbags and seat belt pretensioners will not operate all together. For the safety of all occupants, always wear your seat belts.

The SRS airbag system is designed to activate in response to a severe frontal impact within the shaded area between the arrows in the illustration. The SRS airbags will deploy if the severi- ty of the impact is above the designed threshold level, comparable to an approxi- mate 25 km/h (15 mph) collision when impacting straight into a fixed barrier that does not move or deform. If the severity of the impact is below the above threshold the SRS airbags may not deploy.

level,

2000 4Runner (OM35762U)

51

Collision from the rear

Hitting a curb, edge of pavement or hard material

Falling into or jumping over a deep hole

Collision from the side

Vehicle rollover

Landing hard or vehicle falling

The SRS airbags are not designed to inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low- speed frontal collision.

The SRS airbags may deploy if a seri- ous impact occurs to the underside of your vehicle. Some examples are shown in the illustration.

52

2000 4Runner (OM35762U)

The SRS airbag system consists mainly of the following components, and their loca- tions are shown in the illustration. 1. Front airbag sensors 2. SRS warning light 3. Airbag module for passenger

(airbag and inflator)

4. Airbag sensor assembly 5. Airbag module for driver

(airbag and inflator)

The airbag sensor assembly consists of a safing sensor and airbag sensor.

the

fills

inflators quickly

In a severe frontal impact, sensors detect deceleration and the system triggers the airbag inflators. Then a chemical reaction in the airbags with non- toxic gas to help restrain the forward motion of the occupants. When the airbags inflate, they produce a fairly loud noise and release some smoke and residue along with non- toxic gas. This does not indicate a fire. This gas is nor- mally harmless; however, for those who have delicate skin, it may cause a minor skin irritation. Be sure to wash off any residue as soon as possible to prevent any potential skin irritation. Deployment of the airbags happens in a fraction of a second, so the airbags must inflate with considerable force. While the system is designed to reduce serious inju- ries, it may also cause minor burns or abrasions and swelling. Parts of the airbag module (steering wheel hub, dashboard) may be hot for several minutes, but the airbags themselves will not be hot. The airbags are designed to inflate only once.

the windshield as

A crash severe enough to inflate the air- bags may break the vehicle buckles. In vehicles with a pas- senger airbag the windshield may also be damaged by absorbing some of the force of the inflating airbag.

CAUTION

(cid:1) The SRS airbag system is designed only as a supplement to the prima- ry protection of the driver side and front passenger side seat belt sys- tems. The front seat occupants can be killed or seriously injured by an inflating airbag if they do not wear the available seat belts. During sud- den braking just before a collision, an unrestrained driver or front pas- senger can move forward into direct contact with or close proximity to the airbag which may then deploy during the collision. To ensure max- imum protection in an accident, the driver and all passengers in the ve- hicle must wear their seat belts. Wearing a seat belt during an acci- dent reduces the chances of death or serious injury or being thrown out of the vehicle. For instructions and precautions concerning the seat belt system, see “Seat belts” in this section.

2000 4Runner (OM35762U)

53

(cid:1) Improperly seated and/or restrained infants and children can be killed or seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint system. Toyota strongly recommends infants and children be placed in the rear seat of re- strained. The rear seat is the safest for in- structions concerning the installa- tion of a child restraint system, see “Child restraint” in this section.

the vehicle and properly

infants and children. For

that all

(cid:1) Never put a rear- facing child re- straint system in the front seat be- cause the force of the rapid infla- tion of the passenger airbag can cause death or serious injury to the child.

Move seat fully back

(cid:1) A forward- facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child. For instructions concerning the installation of a child restraint system, see “Child restraint” in this section.

54

2000 4Runner (OM35762U)

(cid:1) Do not sit on the edge of the seat or lean over the dashboard when the vehicle is in use. The airbags inflate with considerable speed and force; you may be killed or serious- ly injured. Sit up straight and well back in the seat, and always use your seat belt.

(cid:1) Do not allow a child to stand up, or to kneel on the front passenger seat. The airbag inflates with con- siderable speed and force; the child may be killed or seriously injured. (cid:1) Do not hold a child on your lap or in your arms. Use a child restraint system in the rear seat. For instruc- tions concerning the installation of a child restraint system, see “Child restraint” in this section.

(cid:1) Do not put objects or your pets on or in front of the dashboard or steering wheel pad that houses the airbag system. They might restrict inflation or cause death or serious injury as they are projected rear- ward by the force of deploying air- bags. Likewise, the driver and front passenger should not hold things in their arms or on their knees.

2000 4Runner (OM35762U)

55

(cid:1) Do not modify or remove any wir- ing. Do not modify, remove, strike or open any components such as the steering wheel pad, steering wheel, column cover, front passen- ger airbag cover, front passenger airbag or airbag sensor assembly. Doing any of these may cause sud- den SRS airbag inflation or disable the system, which could result in death or serious injury. instructions Failure to follow these can result in death or serious injury.

NOTICE

Do not perform any of the following changes without consulting your Toyota dealer. Such changes can in- terfere with proper operation of the SRS airbag system in some cases. (cid:1) Installation of electronic devices such as a mobile two-way radio, cassette tape player or compact disc player

(cid:1) Modification of the suspension sys-

tem

(cid:1) Modification of the front end struc-

ture

(cid:1) Attachment of a grille guard (bull bar, kangaroo bar, etc.), snowplow, winches or any other equipment to the front end

(cid:1) Repairs made on or near the front fenders, front end structure, con- sole, steering column, steering wheel or dashboard near the front passenger airbag

56

2000 4Runner (OM35762U)

This SRS airbag system has a service reminder indicator to inform the driver of operating problems. If either of the follow- ing conditions occurs, this indicates a mal- function of the airbags. Contact your Toyota dealer as soon as possible to ser- vice the vehicle. (cid:1) The light does not come on when the ignition key is turned to the “ACC” or “ON” position, or the light remains on.

(cid:1) The light comes on while driving.

Child restraint— —Child restraint precautions Toyota strongly urges the use of child restraint systems for children small enough to use them. The laws of all fifty states in the U.S.A. and Canada now require the use of a child restraint system. Your vehicle conforms to SAE J1819. If a child is too large for a child restraint system, the child should sit in the rear seat and must be restrained using the vehicle’s seat belt. See “Seat belts” for details.

CAUTION

(cid:1) For effective protection in automo- bile accidents and sudden stops, children must be properly re- strained using a seat belt or child restraint system depending on the age and size of the child. Holding a child in your arms is not a sub- stitute for a child restraint system. In an accident, the child can be crushed against the windshield, or between you and the vehicle’s inte- rior.

In the following cases, contact your Toyota dealer as soon as possible: (cid:1) The SRS airbags have been inflated. (cid:1) The front part of the vehicle (shaded in the illustration) was involved in an accident that was not severe enough to cause the SRS airbags to inflate.

front

(cid:1) The pad section of the steering wheel or cover (shaded in the illustration) is scratched, cracked, or otherwise damaged.

passenger

airbag

NOTICE

Do not disconnect the battery cables before contacting your Toyota dealer.

(cid:1) Toyota strongly urges use of a proper child restraint system which conforms to the size of the child, and is put on the rear seat. Accord- ing to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat. (cid:1) Never put a rear- facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear- facing child restraint system is put on the front seat.

(cid:1) Unless it is unavoidable, do not put a forward- facing child restraint sys- tem on the front seat.

(cid:1) A forward- facing child restraint sys- tem should be put on the front seat only when it is unavoidable. Always move the seat as far back as pos- sible, because the force of a de- ploying airbag could cause death or serious injury to the child.

(cid:1) Make sure that you have complied with all installation instructions pro- vided restraint manufacturer and that the system is properly secured.

child

the

by

2000 4Runner (OM35762U)

57

the manufacturer’s

—Child restraint system A child restraint system for a small child or baby must itself be properly restrained on the seat with either the lap belt or the lap portion of the lap/ shoulder belt. You must carefully con- sult instructions which accompany the child restraint system. To provide proper restraint, use a child restraint system following the manufactur- er’s instructions about the appropriate age and size of the child for the child restraint system. Install the child restraint system correctly following the instructions provided by its manufacturer of the system. General directions are also provided under the fol- lowing illustrations. The child restraint system should be installed on the rear seat. According to accident statistics, the child is safer when properly restrained in the rear seat than in the front seat.

CAUTION

(cid:1) Never put a rear- facing child re- straint system on the front seat. In the event of an accident, the force of the rapid inflation of the airbag can cause death or serious injury if a rear- facing child restraint system is put on the front seat.

(cid:1) Unless it is unavoidable, do not put a forward- facing child restraint sys- tem on the front seat.

(cid:1) A forward- facing child restraint sys- tem should be put on the front seat only when it is unavoidable. Always move the seat as far back as pos- sible, because the force of a de- ploying airbag could cause death or serious injury to the child.

(cid:1) After

installing the child restraint system, make sure it is secured in place following the manufacturer’s instructions. If it is not restrained securely, it may cause death or se- rious the event of a sudden stop or accident.

the child

injury

to

in

than

When not using the child restraint system, keep it secured with the seat belt or place it somewhere other the passenger compartment. This will prevent it from in- juring passengers in the event of a sud- den stop or accident. Your vehicle has anchors for securing the top strap of a child restraint system. The anchor nuts are welded beneath the sheet metal to permit installation of an anchor bracket for a child restraint system. To install an anchor bracket, use an 8 mm (cid:1) 30 mm (cid:1) 1.25 mm coarse thread met- ric bolt and a 10 mm (0.4 in.) spacer. Note that the bolts accompanying many child restraint systems are not metric. You can damage the anchor nuts on your ve- hicle force bolts with different thread into the anchor nuts. For instructions about how to install the anchor bracket, see “—Top strap anchors and locations”.

if you

58

2000 4Runner (OM35762U)

If your child restraint system does not provide any of the necessary parts, you can purchase the from your Toyota dealer. (cid:1) CRS installation kit

following

items

(Part No. 04731- 22012)—contains 1
bolt, 3 types of spacers and 1 locking clip.

(cid:1) Bolt (Part No. 91511- 60830)

—Types of child restraint system Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system following the instructions provided by its manufac- turer.

(A) Infant seat

(B) Convertible seat

2000 4Runner (OM35762U)

59

—Installation with 2- point type seat belt

(C) Booster seat

(A) INFANT SEAT INSTALLATION An infant seat is used in rear- facing position only.

CAUTION

Do not put a rear- facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passen- ger in case of sudden braking or a collision.

60

2000 4Runner (OM35762U)

1. Run

the

lap belt

the center

infant seat

through or around the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the lap belt.

following

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

2. While pressing the infant seat

firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the infant seat securely.

2000 4Runner (OM35762U)

61

CAUTION

3. To remove the infant seat, press the

buckle- release button.

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward- facing and rear- facing position depend- ing on the child’s age and size. When installing, the manufacturer’s instructions about the applicable child’s age and size as well as direction for installing of a child restraint system.

follow

62

2000 4Runner (OM35762U)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap belt is not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, injury. Contact your child Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

CAUTION

Do not put a rear- facing child re- straint system on the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passen- ger in case of sudden braking or a collision.

1. Run

lap belt

the center

through or following around its by the instructions tab into manufacturer and the buckle taking care not to twist the lap belt.

the convertible seat provided insert the

2000 4Runner (OM35762U)

63

2. While pressing

the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the convertible seat securely.

CAUTION

3. To remove the convertible seat, press

the buckle- release button.

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

64

2000 4Runner (OM35762U)

—Installation with 3- point type seat belt

(A) INFANT SEAT INSTALLATION An infant seat is used in rear- facing position only.

CAUTION

(cid:1) Never put a rear- facing child re- straint system in the front seat be- cause the force of the rapid infla- tion of the passenger airbag can cause death or serious injury to the child.

(cid:1) Do not put a rear- facing child re- straint system in the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden brak- ing or a collision.

2000 4Runner (OM35762U)

65

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

1. Run the lap and shoulder belt through or around the infant seat following the instructions provided by its manufactur- er and insert the tab into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended.

the

To hold infant seat securely, make sure the belt is in the lock mode before letting the belt retract.

66

2000 4Runner (OM35762U)

3. While pressing the infant seat

firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the infant seat secure- ly.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

4. To remove the infant seat, press the buckle- release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

2000 4Runner (OM35762U)

67

(B) CONVERTIBLE SEAT INSTALLATION A convertible seat is used in forward- facing and rear- facing position depend- ing on the child’s age and size. When installing, follow the manufacturer’s in- structions about the applicable child’s age and size as well as directions for installing a child restraint system.

CAUTION

(cid:1) Never put a rear- facing child re- straint system in the front seat be- cause the force of the rapid infla- tion of the passenger airbag can cause death or serious injury to the child.

(cid:1) A forward- facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child.

Move seat fully back

68

2000 4Runner (OM35762U)

CAUTION

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

(cid:1) If the seat belt does not function it cannot protect your normally, child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

(cid:1) Do not put a rear- facing child re- straint system in the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden brak- ing or a collision.

1. Run the lap and shoulder belt through or around the convertible seat following its the instructions manufacturer and into the buckle taking care not to twist the belt. Keep the lap portion of the belt tight.

provided insert the

by tab

2000 4Runner (OM35762U)

69

2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be ex- tended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.

3. While pressing

the convertible seat firmly against the seat cushion and seatback, let the shoulder belt retract as far as it will go to hold the convert- ible seat securely.

CAUTION

Push and pull the child restraint sys- tem in different directions to be sure it is secure. Follow all the installation instructions provided by its manufac- turer.

70

2000 4Runner (OM35762U)

4. To remove the convertible seat, press the buckle- release button and allow the belt to retract completely. The belt will move to work for an adult or older child passen- ger.

freely again and be ready

(C) BOOSTER SEAT INSTALLATION A booster seat is used in forward- fac- ing position only.

Move seat fully back

CAUTION

A forward- facing child restraint sys- tem should be allowed to be put on the front seat only when it is un- avoidable. Always move the seat as far back as possible, because the force of a deploying airbag could cause death or serious injury to the child.

2000 4Runner (OM35762U)

71

(cid:1) If the seat belt does not function normally, it cannot protect your child injury. Contact your Toyota dealer immediately. Do not use the seat until the seat belt is fixed.

from

CAUTION

(cid:1) Always make sure the shoulder belt is positioned across the center of child’s shoulder. The belt should be kept away from child’s neck, but not falling off child’s shoulder. Fail- ure the amount of protection in an accident and cause serious injuries in a col- lision.

to do so could reduce

(cid:1) Both high- positioned lap belts and loose- fitting belts could cause seri- ous injuries due to sliding under the lap belt during a collision or other unintended result. Keep the lap belt positioned as low on hips as possible.

(cid:1) For child’s safety, do not place the

shoulder belt under child’s arm.

(cid:1) After inserting the tab, make sure the tab and buckle are locked and that the lap and shoulder portions of the belt are not twisted.

(cid:1) Do not insert coins, clips, etc. in the buckle as this may prevent you from properly latching the tab and buckle.

1. Sit the child on a booster seat. Run the lap and shoulder belt through or around the booster seat and child fol- lowing the instructions provided by its manufacturer and into the buckle taking care not to twist the belt.

insert

tab

the

Make sure the shoulder belt is correctly across the child’s shoulder and that the lap belt is positioned as low as possible on child’s hips. See “Seat belts” for de- tails.

72

2000 4Runner (OM35762U)

—Top strap anchors and locations

Anchor bracket

Bolt

Spacer

730 mm (28.7 in.)

380 mm (15.0 in.)

380 mm (15.0 in.)

2. To remove the child restraint system, press the buckle- release button and al- low the belt to retract.

If your child restraint system requires the use of a top strap, latch the hook onto the anchor bracket and tighten the top strap. See the following instructions to install the anchor bracket.

On the luggage compartment floor a. Using the illustration as a guide, run your fingers across the trim of the filler panel itself to locate the position of the holes underneath.

b. Make a hole in the covering directly above the hole in the luggage compart- ment floor.

c. Insert a 15 mm (0.6 in.) spacer and tighten down for your child restraint system with a bolt. to 16.5—24.7 N⋅m Torque (1.68—2.52 kgf⋅m, 12.2—18.2 ft⋅lbf).

the anchor bracket

the bolt

2000 4Runner (OM35762U)

73

Tilt steering wheel

Outside rear view mirrors—

This model sold in Canada is provided with a bracket set in the glove box, de- signed for use with any of the 2 anchor locations shown in the illustration. If your child restraint system does not provide any of the necessary parts, ask your Toyota dealer. (See “—Child restraint system”.)

To change the steering wheel angle, hold the steering wheel, pull the lock release lever toward you, tilt the steer- ing wheel to the desired angle and re- turn the lever to its original position. When the steering wheel is in a low posi- tion, it will spring up as you release the lock release lever.

CAUTION

(cid:1) Do not adjust the steering wheel

while the vehicle is moving.

(cid:1) After adjusting the steering wheel, try moving it up and down to make sure it is locked in position.

Adjust the mirror so that you can see the side of your vehicle in the mirror. Be careful when judging the size or dis- tance of any object seen in the outside rear view mirror on the passenger’s side. It is a convex mirror with a curved sur- face. Any object seen in a convex mirror will look smaller and farther away than when seen in a flat mirror. On some models, when you push the back window defogger switch, the heater panels in the outside rear view mirrors will quickly clear the surface. To turn on the back window defogger, see “Back window and outside rear view mirror defoggers” in Section 1- 4.

74

2000 4Runner (OM35762U)

CAUTION

(cid:1) Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries.

(cid:1) On some models, since the mirror surfaces can get hot, keep your hands off them when the defogger switch is on.

—Power Rear view mirror control

To adjust a mirror, use the switches. 1. Master switch—To select the mirror to

be adjusted Place the switch at “L” (left) or “R” (right). 2. Control

switch—To move

the mir- the desired

ror P ush direction.

the switch

in

With power windows (door armrest)

Mirror can be adjusted when key is in the “ACC” or “ON” position.

NOTICE

If ice should jam the mirror, do not operate the control or scrape the mir- ror face. Use a spray de-icer to free the mirror.

Without power windows (instrument panel)

2000 4Runner (OM35762U)

75

—Folding rear view mirrors

Anti- glare inside rear view mirror

CAUTION

Do not adjust the mirror while the vehicle is moving. It may cause the driver to mishandle the vehicle and an accident may occur resulting in personal injuries.

for parking

The rear view mirrors can be folded backward restricted areas. To fold the rear view mirror, push back- ward.

in

CAUTION

Do not drive with the mirrors folded backward. Both the driver and pas- senger side rear view mirrors must be extended and properly adjusted before driving.

Adjust the mirror so that you can just see the rear of your vehicle in the mir- ror. To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1
The reflection in the mirror has greater clarity at this position. Night driving—Lever at position 2
Remember that by reducing glare you also lose some rear view clarity.

76

2000 4Runner (OM35762U)

Vanity mirror (front passenger’s side only)

To use the vanity mirrors, swing down the sun visor and open the cover. Type B only—The vanity light comes on when you open the cover.

Type A

Type B

2000 4Runner (OM35762U)

77

78

2000 4Runner (OM35762U)

SECTION 1- 4

OPERATION OF INSTRUMENTS AND CONTROLS Lights, Wipers and Defogger Headlights and turn signals Emergency flashers Instrument panel light control Front fog lights Interior light Personal lights Luggage compartment light Ignition switch light Windshield wipers and washer Back window wiper and washer Back window and outside rear view mirror defoggers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80
81
82
82
82
83
83
84
84
85
86

2000 4Runner (OM35762U)

79

Headlights and turn signals

tail,

license plate,

HEADLIGHTS To turn on the following lights: Twist the headlight/turn signal lever knob. Position 1—Parking, side marker and instrument panel lights Position 2—Headlights and all of above The lights automatically turn off when the driver’s door is opened with the ignition switch turned off. To turn them on again, turn the key to the “ON” position or actu- ate the headlight switch. If you are going to park for over one week, make sure the headlight switch is off.

the

NOTICE

To prevent the battery from being dis- charged, do not leave the lights on for a long period when the engine is not running.

Daytime running light system (on some models) The headlights turn on when the parking brake is released with the engine started, even with the light switch in the “OFF” position. They will not go off until the ignition switch is turned off. To turn on the other exterior lights and instrument panel lights, twist the knob to the position 1. Under the daytime running light system, the headlights turn on at reduced intensity. Twist the knob to the position 2 to turn to full intensity for driving at night.

High- Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever to- ward you (position 2) for low beams. The headlight high beam light indicator (blue light) on the instrument panel will tell you that the high beams are on. Flashing the high beam headlights (position 3)—Pull the way back. The high beam headlights turn off when you release the lever. You can flash the high beam headlights with the knob turned to “OFF”.

the lever all

80

2000 4Runner (OM35762U)

Emergency flashers

NOTICE

To prevent the battery from being dis- charged, do not leave the switch on longer than necessary when the en- gine is not running.

TURN SIGNALS To signal a turn, push the headlight/ turn signal lever up or down to position 1. The key must be in the “ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes. To signal a lane change, move the lever up or down to the pressure point (position 2) and hold it. If the turn signal indicator lights (green lights) on the instrument panel flash faster than normal, a front or rear turn signal bulb is burned out.

flashers,

turn on

the emergency

To push the switch. All the turn signal lights will flash. To turn them off, push the switch once again. Turn on the emergency flashers to warn other drivers if your vehicle must be stopped where it might be a traffic hazard. Always pull as far off the road as pos- sible. The turn signal light switch will not work when the emergency flashers are operat- ing.

2000 4Runner (OM35762U)

81

Instrument panel light control

Front fog lights

Interior light

To adjust the brightness of the instru- ment panel lights, turn the knob.

To turn on the front fog lights, twist the band of the headlight and turn sig- nal switch lever. They will come on only when the headlights are on low beam.

To turn on the interior light, slide the switch. The interior light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the light on when any of the side door is opened. The light goes off when all the side doors are closed.

82

2000 4Runner (OM35762U)

Personal lights (with moon roof)

Personal lights (without moon roof)

Luggage compartment light

To turn on the personal light, push the switch on 1 side. To turn the light off, push the switch on 2 side.

To turn on the personal light, push the switch. To turn the lights off, push the switch once again.

luggage compartment

To turn on the light, slide the switch. The luggage compartment light switch has the following positions: “ON”—Keeps the light on all the time. “OFF”—Turns the light off. “DOOR”—Turns the back door is opened. The light goes off when the back door is closed.

light on when

the

2000 4Runner (OM35762U)

83

Ignition switch light

Windshield wipers and washer (intermittent type)

For easy access to the ignition switch, the ignition switch light comes on when the driver’s door is opened. The light remains on for some time after driver’s door is closed.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Position 3

Intermittent

Slow

Fast

The “INT TIME” band lets you adjust the wiping time interval when the wiper lever is in the intermittent position (position 1). Twist increase the time between sweeps, and downward to decrease it.

the band upward to

84

2000 4Runner (OM35762U)

To squirt washer fluid, pull the lever toward you. If the windshield wipers are off, they will operate a couple of times after the washer squirts. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7- 3. In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

Windshield wipers and washer (mist type)

Back window wiper and washer

In freezing weather, warm the windshield with the defroster before using the washer. This will help prevent fluid from freezing on your windshield, which can block your vision.

the washer

NOTICE

Do not operate the wipers if the wind- shield is dry. It may scratch the glass.

To turn on the windshield wipers, move the lever to the desired setting. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Slow

Fast

the windshield,

For a single sweep of push the lever up and release it. To squirt washer fluid, pull the lever toward you. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7- 3.

To turn on the back window wiper, twist the lever knob upward. The key must be in the “ON” position.

Lever position

Speed setting

Position 1

Position 2

Intermittent

Normal

To squirt washer fluid on the back window, twist the knob upward or downward as far as it will go (position 3 or 4). The knob automatically returns from these positions after you release it. For instructions on adding washer fluid, see “Adding washer fluid” in Section 7- 3.

2000 4Runner (OM35762U)

85

Back window and outside rear view mirror defoggers

NOTICE

Do not operate the back window wip- er if the back window is dry. It may scratch the glass.

To defog or defrost the back window, push the switch with the back window closed. The key must be in the “ON” position. The thin heater wires on the inside of the back window will quickly clear the surface. An indicator light will illuminate to indicate the defogger is operating. On some models, heater panels in the outside rear view mirrors will also quickly clear the surfaces. Push the switch once again to turn the defogger off. The system will automatically shut off af- ter the defoggers have operated about 15
minutes.

2000 4Runner (OM35762U)

86

turn

Make sure you the defoggers off when the surfaces are clear. Leaving the defoggers on for a long time could cause the battery to discharge, especially during stop- and- go driving. The defoggers are not designed for drying rain water or for melting snow.

CAUTION

On some models, since the mirror surfaces can get hot, keep your hands off them when the defogger switch is on.

NOTICE

When cleaning the inside of the back window, be careful not to scratch or damage the heater wires.

SECTION 1- 5

OPERATION OF INSTRUMENTS AND CONTROLS Gauges, Meters and Service reminder indicators Fuel gauge Engine coolant temperature gauge Tachometer Odometer and two trip meters Service reminder indicators and warning buzzers

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

88
88
89
89
90

2000 4Runner (OM35762U)

87

Fuel gauge

Engine coolant temperature gauge

If the fuel tank is completely empty, the malfunction indicator lamp comes on. Fill the fuel tank immediately. The indicator lamp goes off after driving several times. If the indicator lamp does not go off, contact your Toyota dealer as soon as possible.

the

The gauge works when ignition switch is on and indicates the approxi- mate quantity of fuel remaining in the tank. Nearly full—Needle at “F” Nearly empty—Needle at “E” It is a good idea to keep the tank over 1/4 full. If the fuel level approaches “E” or the low fuel level warning light comes on, fill the fuel tank as soon as possible. On inclines or curves, due to the move- ment of fuel in the tank, the fuel gauge needle may fluctuate or the low fuel level warning light may come on earlier than usual.

88

2000 4Runner (OM35762U)

The gauge indicates the engine coolant temperature when the ignition switch is on. The engine operating temperature will vary with changes in weather and engine load. If the needle moves into the red zone, your engine is too hot. If your vehicle