2010 Subaru Tribeca Owners Manual

Download PDF Manual
selected indication is not for the driv- ing range on remaining fuel. ” even if Black plate (153,1) Instruments and controls 3-25 & Journey time The journey time shows the time that has elapsed since the ignition switch was turned to the “START” position. The journey time indication flashes each time a complete hour has elapsed. If the – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 3-26 Instruments and controls display is giving an indication other than the journey time, the display switches to the journey time, flashes for 5 seconds, and returns to its original indication each time a complete hour has elapsed. NOTE The journey time is reset when the ignition switch is turned to the “LOCK” position. It is also reset if the ignition switch is turned to the “LOCK” or “Acc” position prior to restarting of the engine. Black plate (154,1) Light control switch & Headlights WARNING To prevent battery discharge result- ing from accidentally leaving your lights on when your vehicle is parked, the light switch operates only when the ignition switch is in the “ON” position. In any other position, the vehicle’s lights will be out. If you park your vehicle on a road- side at night, use the hazard warn- ing flasher to alert the other drivers. The light switch operates only when the ignition switch is in the “ON” position. To turn on the headlights, turn the knob on the end of the turn signal lever. first position Parking lights, instrument panel illumina- tion, tail lights and license plate light are on. second position Headlights, parking lights, instrument pa- nel lights, and license plate light are on. illumination, tail 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (155,1) & Headlight flasher & Daytime running light system Instruments and controls 3-27 & High/low beam change (dim- mer) To change from low beam to high beam, push the turn signal lever forward. When the headlights are on high beam, the high beam indicator light “ ” on the combina- tion meter also illuminates. To switch back to low beam, pull the lever back to the detent position. CAUTION Do not hold the lever in the flashing position for more than just a few seconds. To flash the headlights, pull the lever toward you and then release it. The high beam will remain on for as long as you hold the lever. The headlight flasher works even though the light switch is in the “OFF” position. When the headlights are on high beam, the high beam indicator light “ ” on the combination meter also illuminates. WARNING The brightness of the illumination of the high beam headlights is reduced by the daytime running light system. The light switch must always be turned to the “ ” position when it is dark outside. The high beam headlights will automati- cally illuminate at reduced brightness when the engine has started, under the following conditions. . The select lever is in a position other than the “P” position. . The parking brake is fully released. . The light switch is in the “OFF” or “ position. NOTE When the light switch is in the “ ” position, the front side marker lights, parking lights and license plate lights are also illuminated. ” 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (156,1) 3-28 Instruments and controls Turn signal lever Illumination brightness con- trol NOTE is turned fully When the control dial upward, the illumination brightness becomes the maximum and the auto- matic dimming function does not work at all. To activate the right turn signal, push the lever up. To activate the left turn signal turn signal, push the turn signal lever down. When the turn is finished, the lever will return automatically. If the lever does not return after cornering, return the lever to the neutral position by hand. To signal a lane change, push the turn signal lever up or down slightly and hold it during the lane change. The turn signal indicator lights will flash in the direction of the turn or lane change. The lever will return automatically to the neutral position when you release it. When the light switch is in the “OFF” position, you can adjust the brightness of the instrument panel illumination for better visibility. The brightness of audio, air conditioner, multi-function display (if equipped) and instrument panel illumination automati- cally dims when the light switch is in the “ ” position. You can adjust brightness of the illumination for better visibility. ” or “ To brighten, turn the control dial upward. To darken, turn the control dial downward. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Headlight beam leveler (if equipped) Adjust the headlight beam level with the following dial positions according to the number of passengers and load condition. Black plate (157,1) Instruments and controls 3-29 – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 3-30 Instruments and controls & For 5-seater models Dial position Number of front seat occupants Number of rear seat occupants Load in the luggage compartment area 1 or 2 Not applicable Not applicable Not applicable Not applicable No load No load Not applicable Not applicable Full load Full load Full load Full load Black plate (158,1) Trailer towing No No Not applicable Not applicable No Yes No Yes Not applicable Not applicable Not applicable Not applicable 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (159,1) Instruments and controls 3-31 & For 7-seater models Dial position Number of front seat occupants Number of 2nd seat occupants Number of 3rd seat occupants Load in the luggage compartment area Trailer towing 1 or 2 No load No load No load Full load Full load Full load Full load No No No No Yes No Yes Not applicable Not applicable Not applicable Not applicable Not applicable 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (160,1) 3-32 Instruments and controls Parking light switch Front fog light switch The indicator meter will are illuminated. light on the combination illuminate when the fog lights The parking light switch operates regard- less of the ignition switch position. By pushing the front end of this switch, following lights will illuminate. – Parking lights – Front and rear side marker lights – Tail lights – License plate lights To turn off, push the rear end of parking light switch. Avoid leaving these lights on for a long time because that will run down the battery. the The front fog lights operate only when the light switch is in the “ However, the front fog lights turn off when the headlights are switched to high beam. ” position. To turn on the front fog lights, turn the fog light switch on the turn signal lever upward to the “ To turn off the front fog lights, turn the switch back down to the “OFF” position. ” position. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Wiper and washer WARNING In freezing weather, do not use the windshield washer until the wind- shield is sufficiently warmed by the defroster. Otherwise the washer fluid can freeze on the windshield, blocking your view. CAUTION . Do not operate the washer con- tinuously for more than 10 sec- onds, or when the washer fluid tank is empty. This may cause overheating of the washer motor. Check the washer fluid level frequently, such as at fuel stops. . Do not operate the wipers when the windshield or rear window is dry. This may scratch the glass, damage the wiper blades and cause the wiper motor to burn out. Before operating the wiper on a dry windshield or rear window, always use the wind- shield washer. If . In freezing weather, be sure that the wiper blades are not frozen to the windshield or rear window before switching on the wipers. Attempting to operate the wiper with the blades frozen to the window glass could cause not only the wiper blades to be damaged but also the wiper mo- tor to burn out. the wiper blades are frozen to the window glass, be sure to operate the defroster, wiper deicer (if equipped) or rear window defog- ger before turning on the wiper. . If the wipers stop during opera- tion because of ice or some other obstruction on the window, the wiper motor could burn out even if the wiper switch is turned off. If this occurs, promptly stop the vehicle in a safe place, turn the ignition switch to the “LOCK” position and clean the window glass to allow proper wiper op- eration. . Use clean water if windshield washer fluid is unavailable. In areas where water freezes in winter, use SUBARU Windshield Washer Fluid or the equivalent. Refer to “Windshield washer Black plate (161,1) Instruments and controls 3-33 fluid” F11-32. Also, when driving the vehicle when there are freezing tempera- tures, use non-freezing type wi- per blades. . Do not clean the wiper blades with gasoline or a solvent, such as paint thinner or benzine. This will cause deterioration of the wiper blades. NOTE . The front wiper motor is protected against overloads by a circuit breaker. The motor operates continuously un- der an unusually heavy load, the circuit breaker may trip to stop the motor temporarily. If this happens, park your vehicle in a safe place, turn off the wiper switch, and wait for approxi- mately 10 minutes. The circuit breaker will reset itself, and the wipers will again operate normally. . Clean your wiper blades and win- dow glass periodically with a washer solution to prevent streaking, and to remove accumulations of road salt or road film. Keep the washer button depressed at least for 1 second so that washer solution will be sprinkled all over the windshield or rear window. – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 3-34 Instruments and controls . Grease, wax, insects or other mate- rial on the windshield or the wiper blades results in jerky wiper operation and streaking on the glass. If you cannot remove those streaks after operating the washer or if the wiper operation is jerky, clean the outer sur- face of the windshield or rear window and the wiper blades using a sponge or soft cloth with a neutral detergent or mild-abrasive cleaner. After cleaning, rinse the window glass and wiper blades with clean water. The glass is clean if no beads form on the glass when you rinse with water. . If you cannot eliminate the streaking even after following this procedure, replace the wiper blades with new ones. For replacement instructions, refer to “Replacement of wiper blades” F11-33. & Windshield wiper and washer switches The wiper operates only when the ignition switch is in the “ON” or “Acc” position. Black plate (162,1) ! Windshield wipers ! Mist (for a single wipe) OFF: Off : Intermittent LO: Low speed HI: High speed To turn the wipers on, push the wiper control lever down. To turn the wipers off, return the lever to the “OFF” position. For a single wipe of the wipers, pull the lever toward you. The wipers operate until you release the lever. ! Wiper intermittent time control 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (163,1) Instruments and controls 3-35 & Rear window wiper and washer switch NOTE When the wiper switch is in the “ ” position, turn the dial to adjust the operat- ing interval of the wiper. The operating interval can be adjusted in nine steps. The intermittent operation interval varies depending on the vehicle speed in any of the adjustment steps (longer when the vehicle speed is low; shorter when the vehicle speed is high). ! Washer To wash the windshield, push the washer button at the end of the wiper control lever. The washer fluid sprays until you release the washer button. The wipers operate while you push the button. The windshield washer fluid warning light illuminates when the washer fluid level in the tank has dropped to the lower limit. If the warning light illumi- nates, refill the tank with fluid. For the tank refilling method, refer to “Wind- shield washer fluid” F11-32. : Washer (accompanied by wiper operation) ON: Continuous INT: Intermittent OFF: Off : Washer ! Rear wiper To turn the rear wiper on, turn the knob on the end of the wiper control lever upward to the “INT” or “ON” position. To turn the wiper off, return the knob on the end of the lever to the “OFF” position. With the switch turned to the “INT” position, the rear wiper will operate inter- mittently at intervals corresponding to the vehicle speed (longer when the vehicle – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 3-36 Instruments and controls speed is low; shorter when the vehicle speed is high). When you subsequently move the select lever of the automatic transmission to the “R” position, the rear wiper will switch to continuous operation. When you move the select lever from the “R” position to some other position, the rear wiper will return to intermittent operation. ! Washer To wash the rear window while the rear wiper is operating, turn the knob on the end of the wiper control lever upward to the “ ” position. The washer fluid sprays until you release the knob. To wash the rear window when the rear wiper is not in use, turn the knob on the end of the wiper control lever downward to the “ ” position. The washer fluid sprays and the wiper operates until you release the knob. Windshield wiper deicer The windshield wiper deicer operates only when the ignition switch is in the “ON” position. To turn on the windshield wiper deicer, push the control switch. The indicator light located on the switch illuminates while the windshield wiper deicer is operating. To turn it off, push the control switch again. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. The windshield wiper deicer will automa- tically shut off after approximately 15 minutes. the windshield wiper blades have been deiced completely before that time, push the control switch to turn it off. If If Black plate (164,1) deicing is not complete, you have to push the control switch to turn it on again. Your SUBARU dealer can set your wind- shield wiper deicer to the continuous operation mode. Contact your SUBARU dealer for details. Once the windshield wiper deicer has to the continuous operation been set mode, it should be in the continuous operation mode at any time when the control switch is pushed to the “ON” position. If the battery voltage drops below the permissible level, continuous operation of the windshield wiper deicer is canceled and the system stops operating. CAUTION To prevent the battery from being discharged, do not operate the windshield wiper deicer continu- ously for any longer than necessary. NOTE . Turn on the windshield wiper deicer if the wipers are frozen to the wind- shield. . If the windshield is covered with snow, remove the snow so that the 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 windshield wiper deicer works effec- tively. . While the windshield wiper deicer is in the continuous operation mode, if the vehicle speed remains at 9 mph (15 km/h) or less for 15 minutes, the wind- shield wiper deicer automatically stops operating. Rear window defogger but- ton The rear window defogger operates only when the ignition switch is in the “ON” position. To turn on the defogger, push the control switch that is located on the climate control panel. The indicator light located on the control switch illuminates while the rear window defogger is operating. To turn it off, push the control switch again. It also turns off when the ignition switch is turned to the “Acc” or “LOCK” position. The defogger will automatically shut off after approximately 15 minutes. If the rear window has been cleared completely Black plate (165,1) Instruments and controls 3-37 before that time, push the control switch to turn it off. If defrosting or defogging is not complete, you have to push the control switch to turn it on again. Your SUBARU dealer can set your rear window defogger to the continuous opera- tion mode. Contact your SUBARU dealer for details. Once the rear window defogger has been set to the continuous operation mode, it should be in the continuous operation mode at any time when the control switch is pushed to the “ON” position. the battery voltage drops below the If permissible level, continuous operation of the rear window defogger is canceled and the system stops operating. CAUTION . Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the rear window. They may damage the conductors printed on the window. . To prevent the battery from being discharged, do not operate the defogger continuously for any longer than necessary. – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (166,1) 3-38 Instruments and controls NOTE The outside mirror defogger also oper- ates while the rear window defogger is operating. & Type B inside mirror (if equipped) Mirrors Always check that the inside and outside mirrors are properly adjusted before you start driving. & Type A inside mirror (if equipped) The mirror has a day and night position. Pull the tab at the bottom of the mirror toward you for the night position. Push it away for the day position. The night position reduces glare from headlights. 1) Rear view image display 2) Electronic compass display 3) Auto dimming indicator 4) Multifunction button 5) Photosensor The mirror has the following features. . Rear view image display . Auto-dimming function for anti-glare capability . Electronic compass display You can display the various functions of these features based on how long you press the multifunction button. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Period of time multi- function button is pressed Briefly Gear position R (reverse) Function displayed Rear view display ON/OFF* More than 3 seconds Help lines indica- tion ON/OFF Except R (reverse) Briefly 3 to 6 seconds 6 to 9 seconds 9 to 12 seconds Auto-dimming function ON/OFF* Electronic com- pass display ON/ OFF Enter the com- pass zone setting mode Enter the com- pass calibration mode *: The setting returns to “ON” as a default setting every time the ignition switch is turned to the “ON” position. ! Rear view image display When the ignition switch is “ON” and the select lever is set to “R”, the rear view camera automatically displays the rear view image behind the vehicle on the inside mirror. Also, the following help lines are indicated as a guide to help you realize the actual distance from the display. 1) Vehicle width line (oblique vertical line) 2) Approx. 10 feet (3 m) from the bumper (green horizontal line) 3) Approx. 6.5 feet (2 m) from the bumper (green horizontal line) 4) Approx. 3 feet (1 m) from the bumper (yellow horizontal line) 5) Approx. 1.5 feet (0.5 m) from the bumper (red horizontal line) These help lines are removable. To remove the help lines, perform the follow- ing procedure. 1. Display the rear view image on the mirror. 2. Press the multifunction button for more than 3 seconds to remove the helplines. To display the help lines, press the multi- function button for more than 3 seconds. Black plate (167,1) Instruments and controls 3-39 For precautions about the rear view camera and the rear view image, refer to “Rear view camera” F6-22. ! Auto-dimming function The auto-dimming function is an anti-glare capability which automatically reduces glare coming from headlights of vehicles behind you. By briefly pressing the multifunction but- ton, the auto-dimming function is toggled on or off. When the auto-dimming function is on, the auto dimming indicator light (green) will illuminate. Even with the mirror in anti-glare mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. if – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (168,1) 3-40 Instruments and controls The mirror has a photosensor attached on both the front and back sides. Use care not to cover the sensors with stickers, or other similar items. Periodically wipe the sensors clean using a piece of dry soft cotton cloth or an applicator. NOTE When cleaning the mirror, use a paper towel or similar item dampened with glass cleaner. Do not spray glass cleaner directly on the mirror surface. By doing so, the sprayed glass cleaner could enter the inside of the mirror housing. That may cause a malfunction in the mirror. ! Electronic compass display By pressing the multifunction button for 3 to 6 seconds, the compass display is toggled on or off. When the compass display is on, an illuminated compass reading will appear on the mirror. Using the electronic compass properly, the following compass zone adjustment and compass calibration will be neces- sary. ! Compass zone adjustment 1. The compass zone has been set to zone “8” at the time of shipment from the factory. Refer to the “Compass calibration zones” map, which is attached to the end of this manual to verify that the compass zone setting is correct for your geographi- cal location. 2. Press and hold the multifunction but- ton for 6 to 9 seconds, and then release it. The zone number will be displayed. 3. Press the multifunction button repeat- edly to cycle the display through all possible zone settings. Stop cycling when the correct zone number for your location is displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the multifunction but- ton for 9 to 12 seconds, and then release it. The compass will enter the calibration mode, then “C” and the direction will be displayed. “C” 4. Drive slowly in a circle until disappears from the display. Driving in two or three circles might be necessary. The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the com- pass to read inaccurately. You will notice any outside influence if the compass tends to read in only one particular direction. Should you encounter this situation, return to step 1 of the above procedure and recalibrate the compass. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 & Type C inside mirror (if equipped) or off. When the compass is on, an illuminated compass reading will appear in the lower part of the mirror. Even with the mirror in anti-glare mode, the mirror surface turns bright the transmission is shifted into reverse. This is to ensure good rearward visibility during reversing. ! Photosensors if Left button 1) 2) Auto dimming indicator 3) Photosensor 4) Right button This mirror has an anti-glare feature which automatically reduces glare coming from headlights of vehicles behind you. It also contains a built-in compass. . By pressing and releasing the left button, the automatic dimming function is toggled on or off. When the automatic dimming function is on, the auto dimming indicator light (green) located to the right of the button will illuminate. . By pressing and releasing the right button, the compass display is toggled on The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mirror dimmer to help prevent you from being blinded. For this reason, use care not to cover the sensors with stickers, or other similar items. Periodically wipe the Black plate (169,1) Instruments and controls 3-41 sensors clean using a piece of dry soft cotton cloth or an applicator. ! Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 seconds then release, and the compass will enter the calibration mode. “CAL” and direction will be displayed. 4. Drive slowly in a circle until “CAL” disappears from the display (approxi- mately two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recali- brate the mirror. – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 3-42 Instruments and controls ! Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map attached to the end of this manual to verify that the compass zone setting is correct for your geographical location. 2. Press and hold the right button for 3 seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right-hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the correct zone setting for your location is displayed. 4. Releasing the button for 3 seconds will exit the zone setting mode. Black plate (170,1) & Outside mirrors ! Remote control mirror switch ! Convex mirror (passenger side) WARNING Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the distance of vehicles behind you when changing lanes. Use the inside mirror (or glance backwards) to determine the actual size and dis- tance of objects that you view in convex mirror. The remote control mirrors operate only when the ignition switch is in the “ON” or “Acc” position. 1. Turn the knob to the “L” side to adjust the left-hand mirror or to the “R” side to adjust the right-hand mirror. 2. Move the knob in the direction you want to move the mirror. 3. Return the knob to the neutral position to prevent unintentional operation. The mirrors can also be adjusted manu- ally. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 ! Outside mirror defogger than necessary. ! Power folding mirror switch (if equipped) The outside mirror defogger shares the control switch with the rear window de- fogger. Therefore, the outside mirror de- fogger always operates with the rear window defogger. If the rear window defogger is set to the continuous operation mode, the outside mirror defogger also follows the contin- uous setting. For details, refer to “Rear window defog- ger button” F3-37. CAUTION To prevent the battery from being discharged, do not operate the de- fogger continuously for any longer 1) Power folding mirror switch The power folding mirror switch operates only when the ignition switch is in the “ON” or “Acc” position. To fold the outside mirrors, push the power folding mirror switch. To unfold the mirrors, push the switch again. NOTE . When the temperature is low, the outside mirrors may stop during opera- tion. Push the switch again. When the outside mirrors do not work by switch operation, move them several times Black plate (171,1) Instruments and controls 3-43 manually. This makes it possible to operate them by switch operation. . When you operate the power folding mirror switch continuously, it may temporarily stop working. This is not a malfunction. Operate it again after waiting for a short period of time. . When you unfold the outside mirrors manually, the mirrors may become unstable. Be sure to unfold the mirrors the outside by switch operation. mirrors are still unstable, fold the mirrors again manually and then unfold them by switch operation. If 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (172,1) 3-44 Instruments and controls Tilt steering wheel 5. Make sure that the steering wheel is securely locked by moving it up and down. Horn WARNING Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and result in personal injury. to the seat position. Refer 1. Adjust “Front seats” F1-2. 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Pull the lever up to lock the steering wheel in place. To sound the horn, push the horn pad. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Ventilator.............................................................. Airflow ................................................................ Ventilator ............................................................ Automatic climate control system ..................... Control panel ...................................................... Rear air conditioner (if equipped)......................... Temperature sensors........................................... 4-2 4-2 4-4 4-5 4-5 4-8 4-9 Operating tips for heater and air conditioner....................................................... 4-10 Cleaning ventilator grille..................................... 4-10 Efficient cooling after parking in direct sunlight ........................................................... 4-10 Black plate (7,1) Climate control Lubrication oil circulation in the refrigerant circuit.............................................................. Checking air conditioning system before summer season ............................................................ Cooling and dehumidifying in high humidity and low temperature weather conditions ................. Air conditioner compressor shut-off when engine is heavily loaded.............................................. Refrigerant for your climate control system ........ Air filtration system ........................................... Replacing the air filter........................................ 4-10 4-10 4-10 4-10 4-10 4-11 4-11 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 4-2 Climate control Ventilator & Airflow Ventilator and airflow : Standard : If equipped Black plate (176,1) 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 ! Airflow mode selection *: If equipped Black plate (177,1) Climate control 4-3 – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (178,1) 4-4 Climate control & Ventilator ! Center ventilators ! Side ventilators ! Rear ventilators (if equipped) Move the tab up and down or right and left to adjust the flow direction. 1) Open 2) Close Move the tab up and down or rotate right and left to adjust the flow direction. Move the tab up and down or right and left to adjust the flow direction. To open the ventilator, turn the side grille open/close wheel upward. To close it, turn the wheel downward. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Automatic climate control system NOTE . Operate the automatic climate con- trol system when the engine is running. . The blower fan rotates at a low speed when the engine coolant tem- perature is low. For efficient defogging or dehumidify- ing in cold weather, press the “A/C” button. . Even when cooling is not necessary, setting the temperature much lower than the current outlet air temperature turns on the air conditioner compres- sor automatically and the indicator light on the “A/C” button illuminates. . 7-seater models each have a rear air conditioner. The fan speed of the rear air conditioner can be adjusted, but other adjustments (outlet air tempera- ture, air distribution, etc.) are not possible for the rear air conditioner. For details, refer to “Rear air condi- tioner” F4-8. The automatic climate control system automatically controls outlet air tempera- ture, fan speed, airflow distribution, air inlet control, and air conditioner compres- sor operation. It activates when the Black plate (179,1) Climate control 4-5 ! AUTO button AUTO mode operation: “AUTO” button is pressed, and is used to maintain a constant, comfortable climate within the passenger compartment. The temperature can be set within a range of 65 to 858F (18 to 328C). & Control panel Fan speed control dial Temperature control dial (driver’s side) 1) 2) Defroster button 3) 4) Rear window defogger button (Refer to “Rear window defogger button” F3-37.) (passenger’s Temperature control dial side) 5) 6) Air conditioner button 7) Airflow mode selection button 8) Air inlet selection button 9) OFF button 10) AUTO button When the “AUTO” button is pressed, the indicator light on the button illuminates. In this state, fan speed, airflow distribution, air inlet control, and air conditioner com- pressor operation are automatically con- trolled. Manual mode operation: If you operate any of the buttons on the control panel other than the “OFF” button and temperature control dial during auto- matic mode operation, the indicator light will turn off. You can then manually control the system as desired using the button you operated. To change the system back to the AUTO mode, press the “AUTO” button. – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 4-6 Climate control ! OFF button ! Temperature control dial The Automatic Climate Control system turns off (the air conditioner compressor and fan turn off) when the “OFF” button is pressed. When the “OFF” button is pressed, the outside air inlet selection OFF) is automatically selected. introduction mode (air Driver’s side Black plate (180,1) passenger’s side. Each temperature setting is shown on the display. With the dial set at your desired temperature, the system automatically adjusts the tempera- ture of air supplied from the outlets such that the desired temperature is achieved and maintained. Turning the dial counterclockwise and releasing it reduces the temperature by 18F (0.58C). Turning the dial clockwise and releasing it increases the temperature by 18F (0.58C). Holding the dial in either turned position causes the temperature to change continuously. With the minimum temperature set, the system gives maximum cooling perfor- mance. With the maximum temperature set, the system gives maximum heating performance. Passenger’s side It is possible to make separate tempera- the driver’s side and ture settings for 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 ! – Defroster button system to the AUTO mode by pushing the “AUTO” button or turn off by pushing the “OFF” button. Alternatively, push the “ ” button again to return the system to the setting that was selected before you activated the defros- ter. ! Fan speed control dial ”. When the “ To defrost or dehumidify the windshield and front door windows, push the defros- ter button “ ” button is pushed, the indicator light on the button illuminates and the following operation is performed. . The outside air is drawn into the passenger compartment and the airflow is directed towards the windshield and the front door windows. . The air conditioner compressor auto- matically operates to quickly defog the windshield. However, the indicator light on the air conditioner button will not illumi- nate. After eliminating the fogging from the windshield, return the climate control The fan speed control dial has 7 positions: AUTO position and 6 different fan speed positions. The fan speed is shown on the center of the dial. in the With the fan speed control dial AUTO position, the fan speed changes automatically corresponding the various conditions: air temperature inside and outside of the passenger’s compartment, Black plate (181,1) Climate control 4-7 intensity of the sunlight, etc. ! A/C – Air conditioner button If the windshield starts to fog when the climate control system is operated in the AUTO mode, push the air conditioner button to defog and dehumidify. When this button is pushed, the air conditioner compressor turns on and the indicator light on the button illuminates. After eliminating the fogging from the windshield, set the system back to the AUTO mode by pushing the “AUTO” button. NOTE The air conditioner compressor does not operate when the outside air tem- perature is below 328F (08C). – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (182,1) to the OFF position as soon as the outside dusty condition clears. NOTE When driving on a dusty road or behind a vehicle that emits unpleasant exhaust gases, set the air inlet selection button to the ON position. From time to time, return the air inlet selection button to the OFF position to draw outside air into the passenger compartment. & Rear air conditioner (if equipped) 4-8 Climate control ! Airflow mode selection button ! Air inlet selection button Select the desired airflow mode by push- ing the airflow mode selection button. The selected airflow mode is shown on the center of the dial. (Ventilation): Airflows through the instrument panel outlets. (Bi-level): Airflows through the instru- ment panel outlets and the foot outlets. (Heat): Airflows through the instrument panel outlets, the foot outlets, and some through the windshield defroster outlets. (Heat-def): Airflows through the instru- ment panel outlets, the windshield defros- ter outlets, and the foot outlets. ON position (recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. The indicator light will illuminate. OFF position (outside air): Outside air is drawn into the passenger compartment. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. The indicator light will turn off. WARNING Continued operation in the ON posi- tion may fog up the windows. Switch The rear air conditioner blows cool air out the rear ventilators while the “A/C” of 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 button on the control panel is in the “ON” position. The fan speed of the rear air conditioner can be adjusted using the rear air conditioner dial behind the center console. The fan speed can be adjusted in four steps by turning the dial. Turn the dial to the “OFF” position to stop the fan. NOTE . When the “A/C” button is in the “OFF” position and when the “A/C” indicator is not illuminated during AUTO mode operation, the air condi- tioner compressor does not operate, meaning that the system merely blows uncooled air out of the ventilators. . The outlet air temperature of the rear air conditioner cannot be adjusted. . The rear air conditioner cannot be used as a heater. & Temperature sensors Interior air temperature sensor 1) 2) Solar sensor The automatic climate control system employs several sensors. These sensors are delicate. If they are treated incorrectly and become damaged, the system may not be able to control the interior tempera- ture correctly. To avoid damaging the sensors, observe the following precau- tions. – Do not subject the sensors to impact. – Keep water away from the sensors. – Do not cover the sensors. The sensors are located as follows. – Solar sensor: beside windshield defroster grille Black plate (183,1) Climate control 4-9 – Interior air temperature sensor: on the side of the driver-side part of the center panel – Outside temperature sensor: behind front grille 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 4-10 Climate control Operating tips for heater and air conditioner & Cleaning ventilator grille Always keep the front ventilator inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any accumulation of insects and leaves on the condenser. & Efficient cooling after parking in direct sunlight After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cooling efficiency. & Lubrication oil circulation in the refrigerant circuit Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-season to circulate its oil. & Checking air conditioning system before summer sea- son Check the air conditioner unit for refriger- ant leaks, hose conditions, and proper operation each spring. Have the air con- ditioning system checked by your SUBARU dealer. & Cooling and dehumidifying in high humidity and low tem- perature weather conditions Under certain weather conditions (high relative humidity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning Black plate (184,1) system. & Air conditioner compressor shut-off when engine is heavily loaded To improve acceleration and gas mileage, the air conditioner compressor is designed to temporarily shut off during air condi- tioner operation whenever the accelerator is fully depressed such as during rapid acceleration or when driving on a steep upgrade. & Refrigerant for your climate control system Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the meth- od of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (185,1) Climate control 4-11 Air filtration system & Replacing the air filter Replace the filter element according to the replacement schedule shown in the fol- lowing. This schedule should be followed to maintain the filter’s dust collection ability. Under extremely dusty conditions, the filter should be replaced more fre- quently. It is recommended that you have your filter checked or replaced by your SUBARU dealer. For replacement, we recommend the use of a genuine SUBARU air filter kit. Replacement schedule: Every 15 months or 15,000 miles (24,000 km) whichever comes first 2. Unhook the strap. 1. Remove the instrument panel side cover. NOTE The instrument panel side cover is held in place with four pins. 3. Remove the glove box by detaching the one clip on the side. – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 4-12 Climate control Black plate (186,1) 4. Remove the air filter cover by detach- ing the five clips. 6. Replace the air filter with a new one. 7. 8. Install the air filter cover. Install the glove box. 10. Secure the glove box with the one clip. 11. Install the instrument panel side cover. 5. Unhook the air filter and draw it out. 9. Attach the strap to the hook. 12. Label installation Attach the caution label door. to the driver’s 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 CAUTION Contact your SUBARU dealer if the following occurs, even if it is not yet time to change the filter. – Reduction of the airflow through the vents. – Windshield gets easily fogged or misted. NOTE The filter can influence the air condi- tioning, heating and defroster perfor- mance if not properly maintained. Black plate (187,1) Climate control 4-13 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (2,1) — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — Left Page Model "ALL_MODEL_MEMO" EDITED: 2007/ 6/ 22 Black plate (9,1) Audio 5-2 Antenna system .................................................. 5-2 Printed antenna................................................... 5-2 FM reception ....................................................... 5-2 Installation of accessories.................................. 5-3 Audio set ............................................................. 5-3 Type A audio set ................................................. 5-3 Type B audio set ................................................. 5-4 Type A audio set (if equipped) ........................... Radio operation................................................... 5-4 Compact disc player operation ........................... 5-10 Type B audio set (if equipped).......................... Radio operation ................................................. Built in CD changer operation ............................ Audio control buttons ....................................... MODE button..................................................... Auxiliary input jack............................................ Rear Seat Entertainment (RSE) system operation (if equipped) ................................... Precautions to observe when handling a compact disc................................................... 5-15 5-15 5-21 5-26 5-26 5-28 5-29 5-29 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Black plate (190,1) any other material over the antenna portion of the rear window glass. Installation of accessories Always consult your SUBARU dealer before installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or they are not suited for the vehicle. if & FM reception Although FM is normally static free, reception can be affected by the surround- ing area, atmospheric conditions, station strength and transmitter distance. Build- ings or other obstructions may cause momentary static, flutter or station inter- ference. reception continues to be unsatisfactory, switch to a stronger station. NOTE If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio malfunction. If 5-2 Audio Antenna system & Printed antenna CAUTION Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window. The antenna is printed on the inner surface of the rear window glass. NOTE Antenna performance will deteriorate significantly if you apply tinting film or 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 Audio set & Type B audio set Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details. & Type A audio set . Radio operation: refer to page 5-15 . Built-in CD changer operation: refer to page 5-21 . Radio operation: refer to page 5-4 . CD (compact disc) player operation: refer to page 5-10 Black plate (191,1) Audio 5-3 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 5-4 Audio Type A audio set (if equipped) The audio set will operate only when the ignition switch is in the “Acc” or “ON” position. & Radio operation Black plate (192,1) (1) Satellite radio mode button (2) FM AM mode button (3) Auxiliary audio unit and Rear seat entertainment selection button (4) Tuning button (5) AUDIO button (6) Power switch, volume control dial (7) Seek button (8) Scan button (9) Tone and Balance button (10) Preset button ! Power switch and volume control The dial (6) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and balance adjustment. ! Tone and balance control The volume control dial (6) normally functions as a volume control. This dial becomes a control for Bass, Midrange, Treble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 sec- onds. 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 ! To change tone and balance control modes the “TONE BAL” Each brief press of button (9) changes control modes in the following sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the volume control.) The “TONE BAL” button is used for selecting the following control modes. Black plate (193,1) Audio 5-5 – CONTINUED – 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 5-6 Audio Control mode (range of le- vels) Bass control (−6 to +6) Midrange control (−6 to +6) Treble control (−6 to +6) Fader control (R9 to F9) Balance control (L9 to R9) Turn counterclockwise Turn clockwise For less bass sound For more bass sound For less midrange sound For more midrange sound For less treble sound For more treble sound To increase rear speaker vo- lume and decrease front speak- er volume To increase front speaker vo- lume and decrease rear speaker volume To increase left speaker volume and decrease right speaker vo- lume To increase right speaker vo- lume and decrease left speaker volume Volume control (0 to 40) For less volume AUX volume control* (0 to 40) For less volume *: Only when an AUX audio product is connected. For more volume For more volume Black plate (194,1) ! FM/AM radio ! FM/AM selection button Push the “FM AM” button (2) when the radio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2 or AM reception. ! Stereo indicator The stereo indicator “ST” will illuminate when an FM stereo broadcast is received. ! Manual tuning Press the “ ” side of the “TUNE TRACK” button (4) to increase the tuning frequency and press the “ ” side of the button to decrease it. Each time the button is pressed, the frequency interval can be changed be- tween 10 kHz in the AM mode and 0.2 MHz in the FM mode. If you hold down the “ the button, the tuning frequency will increase continuously, and if you hold down the “ ” side of the button, the tuning frequency will decrease continuously. Release the button when your desired frequency is reached. ” side of 北米Model "A3150BE-A" EDITED: 2009/ 6/ 23 the “TUNE TRACK” button, NOTE While you are holding down either side of the tuning frequency will not stop chan- ging even if the frequency of a recei- vable station is reached. ! Seek tuning If you press the “ ” side of the ” or “ “SEEK FLDR” button (7), the radio will automatically search for a receivable station and stop at the first one it finds. This function may not be available, how- ever, when radio signals are weak. In such a situation, perform manual tuning to select the desired station. ! Automatic tuning (SCAN) Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for 5 seconds while displaying the frequency, after which scanning will con- tinue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. Press the “ ” side of the “SEEK FLDR” button (7) again to cancel the scan mode and to stop on any displayed ” or “ frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function prop-

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2010 Subaru Tribeca Owners Manual