2007 Subaru Tribeca Owners Manual

Download PDF Manual
When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside. (cid:132) Power windows To avoid serious personal injury caused by entrapment, you must do the following. (cid:121) When operating the power win- dows, be extremely careful to pre- vent anyone’s fingers, arms, neck or head from being caught in the window. (cid:121) Always lock the passengers’ win- dows using the lock switch when children are riding in the vehicle. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power win- dow. The power windows operate only when the ignition switch is in the “ON” position. 200727 1) Lock switch 2) For driver’s window 3) For front passenger’s window 4) For rear left window 5) For rear right window All door windows can be controlled by the power window switch cluster at the driver side door. – CONTINUED – A3120BE-B.book 20 ページ２００６年５月３０日　火曜日　午前９時３２分 2-20 Keys and doors (cid:86) Operating the driver’s window 200728 1) Open 2) Automatically open To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and re- lease it, and the window will fully open. To stop the window halfway, pull the switch up lightly. To open the passengers’ windows, push the appropriate switch down and hold it until the window reaches the desired posi- tion. 200729 To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:86) Operating the passengers’ windows 200731 To close the window, pull the switch up and hold it until it reaches the desired po- sition. 200730 A3120BE-B.book 21 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:86) Locking the passengers’ windows (cid:84) Passengers’ side switches Keys and doors 2-21 200732 200733 Front passenger’s window switch 1) Open 2) Close To open the window, push the switch down and hold it until the window reaches the desired position. To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ win- dows cannot be opened or closed. Press the switch again to cancel the pas- sengers’ window locking. NOTE When the lock switch is pushed to the “LOCK” position, the indicator lights in the passenger’s window switches (in- cluded in the power window switch cluster on the driver’s door) all go out. 200734 Rear passengers’ window switches 1) Open 2) Close To close the window, pull the switch up and hold it until the window reaches the desired position. When the lock switch on the power win- dow switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches. A3120BE-B.book 22 ページ２００６年５月３０日　火曜日　午前９時３２分 2-22 Keys and doors Rear gate 200736 200894 200735 The rear gate can be locked and unlocked using either the keyless entry system or the power door locking switch. Refer to the “Power door locking switches” and “Remote keyless entry system” sec- tions in this chapter. To open the rear gate, first unlock the rear gate lock then push the button. To close the rear gate, lower it slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip. (cid:121) To prevent dangerous exhaust gas from entering the vehicle, al- ways keep the rear gate closed while driving. (cid:121) Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip from inside the cargo space. There is a danger of your hand be- ing caught and injured. 1) Reflectors When the rear gate is open, do not place a heavy item on either reflec- tor. Also, do not sit on either reflec- tor. Doing so could break the reflec- tor. A3120BE-B.book 23 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:121) Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open. (cid:121) Be careful not to hit your head or face on the rear gate when open- ing or closing the rear gate and when loading or unloading cargo. NOTE Should the rear gate be unable to be unlocked due to a discharged battery, a fault in the door locking/unlocking system or other causes, you can un- lock it by manually operating the rear gate lock release lever. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” section in chapter 9. Moonroof (if equipped) (cid:121) Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is involved in an accident. To avoid serious personal injury caused by entrapment, you must do the following. (cid:121) Before closing the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moon- roof. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof. (cid:121) Never try to check the anti-entrap- ment function by deliberately placing part of your body in the moonroof. Keys and doors 2-23 (cid:121) Do not sit on the edge of the open moonroof. (cid:121) Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut. (cid:121) The anti-entrapment function does not operate when the moon- roof is being tilted down. Be sure to confirm that it is safe to do so before tilting the moonroof down. The moonroof has both tilting and sliding functions. The moonroof operates only when the ig- nition switch is in the “ON” position. – CONTINUED – A3120BE-B.book 24 ページ２００６年５月３０日　火曜日　午前９時３２分 2-24 Keys and doors (cid:132) Tilt function 200737 1) Tilt up 2) Tilt down The tilting function will only operate when the moonroof is fully closed. Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof. Release the switch after the moonroof has been raised or has been lowered com- pletely. Pushing the switch continuously may cause damage to the moonroof. NOTE One-touch operation does not take place when the moonroof is tilted up and down. Push the switch continu- ously to tilt the moonroof up and down. (cid:132) Sliding function 200738 1) Open 2) Close Push the “Open/Close” switch rearward to open the moonroof. The sun shade will also be opened together with the moon- roof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway. Push it again to close the moonroof completely. To stop the moonroof at a selected mid- way position while opening or closing it, momentarily push the “OPEN” or “CLOSE” side. the switch to After washing the vehicle or after it rains, wipe away water on the roof prior to open- ing the moonroof to prevent drops of water from falling into the passenger compart- ment. (cid:132) Anti-entrapment function When the moonroof senses an object trapped between its glass and the vehi- cle’s roof during closure, it automatically moves back to either of the following posi- tions according to the point at which it senses the object: (cid:121) When the moonroof senses the object at a point between the halfway stop posi- tion and fully closed position, it moves back to the halfway stop position and stops there. (cid:121) When the moonroof senses the object at a point between the halfway stop posi- tion and fully open position, it moves back to the fully open position and stops there. The anti-entrapment function may also be activated by a strong shock on the moon- roof even when there is nothing trapped. NOTE For the sake of safety, it is recommend- ed that you avoid driving with the moonroof fully opened. A3120BE-B.book 25 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:132) Sun shade Keys and doors 2-25 200739 The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back. A3120BE-B.book 26 ページ２００６年５月３０日　火曜日　午前９時３２分 A3120BE-B.book 1 ページ２００６年５月３０日　火曜日　午前９時３２分 Instruments and controls Ignition switch .................................................... LOCK ...................................................................... ACC .......................................................................... ON ............................................................................ START ...................................................................... Key reminder chime ............................................... Ignition switch light ................................................ Hazard warning flasher ...................................... Meters and gauges ............................................. Combination meter illumination ............................ Canceling the function for meter needle/ gauge movement and combination meter sequential illumination upon turning on the ignition switch ...................................................... Speedometer ........................................................... Odometer ................................................................. Double trip meter .................................................... Tachometer ............................................................. Fuel gauge ............................................................... Temperature gauge ................................................ Warning and indicator lights ............................. Seatbelt warning light and chime .......................... SRS airbag system warning light .......................... Front passenger’s frontal airbag ON and OFF indicators .............................................................. CHECK ENGINE warning light/Malfunction indicator lamp ....................................................... Charge warning light .............................................. Oil pressure warning light ..................................... AT OIL TEMPerature warning light ....................... 3-3 3-3 3-4 3-4 3-4 3-5 3-5 3-5 3-5 3-5 3-6 3-7 3-7 3-7 3-8 3-8 3-9 3-9 3-10 3-11 3-12 3-13 3-13 3-13 3-14 Rear differential oil temperature warning light ........................................................................ Low tire pressure warning light ............................ ABS warning light ................................................... Brake system warning light ................................... Low fuel warning light ............................................ Door open warning light ........................................ Windshield washer fluid warning light ................. All-Wheel Drive warning light ................................ Vehicle Dynamics Control operation indicator 3-14 3-14 3-16 3-16 3-17 3-17 3-18 3-18 3-18 light ........................................................................ Vehicle Dynamics Control warning light/Traction Control system OFF indicator light .................... Security indicator light ........................................... SPORT mode indicator light .................................. Selector lever/Gear position indicator .................. Turn signal indicator lights .................................... High beam indicator light ....................................... Cruise control indicator light ................................. Cruise control set indicator light .......................... Headlight indicator light ......................................... Front fog light indicator light ................................. Daytime running light indicator light .................... 3-18 3-19 3-20 3-20 3-20 3-20 3-20 3-21 3-21 3-21 3-21 Clock .................................................................... 3-21 Outside temperature indicator .......................... 3-22 Multi function display (Vehicle without Navigation System) ......................................... 3-23 3-23 Current fuel consumption ...................................... 3-24 Average fuel consumption ..................................... Driving range on remaining fuel ............................ 3-24 A3120BE-B.book 2 ページ２００６年５月３０日　火曜日　午前９時３２分 Instruments and controls Journey time ........................................................... Headlights ............................................................... High/low beam change (dimmer) .......................... Headlight flasher .................................................... Daytime running light system ............................... 3-25 Light control switch ........................................... 3-26 3-26 3-26 3-27 3-27 Turn signal lever ................................................. 3-27 Illumination brightness control ......................... 3-28 Parking light switch ........................................... 3-28 Front fog light switch ......................................... 3-29 Wiper and washer ............................................... 3-29 3-30 3-32 Windshield wiper deicer .................................... 3-33 Rear window defogger button ........................... 3-33 Mirrors ................................................................. 3-34 3-34 3-35 3-36 Tilt steering wheel .............................................. 3-37 Horn ..................................................................... 3-37 Inside mirror ........................................................... Auto-dimming mirror/compass (if equipped) ...... Outside mirrors ....................................................... Windshield wiper and washer switches ............... Rear window wiper and washer switch ................ A3120BE-B.book 3 ページ２００６年５月３０日　火曜日　午前９時３２分 Ignition switch Instruments and controls (cid:121) Never turn the ignition switch to “LOCK” while the vehicle is being driven or towed because that will lock the steering wheel, prevent- ing steering control. And when the engine is turned off, it takes a much greater effort than usual to steer. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child or others. Children could operate the power windows, the moonroof or other controls or even make the vehicle move. Do not attach a large key holder or key case to either key. If it banged against your knees or hands while you were driving, it could turn the ig- nition switch from the “ON” position to the “Acc” or “LOCK” position, thereby stopping the engine. Also, if the key is attached to a keyholder or to a large bunch of other keys, cen- trifugal force may act on it as the ve- hicle moves, resulting in unwanted turning of the ignition switch. The ignition switch has four positions: LOCK, ACC, ON and START. Instruments and controls 3-3 ignition switch NOTE (cid:121) Keep the in the “LOCK” position when the engine is not running. (cid:121) Using electrical accessories for a long time with the ignition switch in the “ON” or “ACC” position can cause the battery to go dead. (cid:121) If the ignition switch will not move from the “LOCK” position to the “ACC” position, turn the steering wheel slight- ly to the left and right as you turn the ignition switch. (cid:132) LOCK The key can only be inserted or removed in this position. The ignition switch will lock the steering wheel when you remove the key. If turning the key is difficult, turn the steer- ing wheel slightly to the right and left as you turn the key. 300500 – CONTINUED – A3120BE-B.book 4 ページ２００６年５月３０日　火曜日　午前９時３２分 3-4 Instruments and controls ing cases: (cid:132) ACC In this position the electrical accessories (radio, accessory power outlet, etc.) can be used. (cid:132) ON This is the normal operating position after the engine is started. (cid:132) START 300501 The key can be turned from “ACC” to “LOCK” only when the selector lever is in the “P” position. Do not turn the ignition switch to the “START” position while the engine is running. The engine is started in this position. The starter cranks the engine to start it. When the key is released (after the engine has started), the key automatically returns to the “ON” position. If your registered key fails to start the en- gine, pull out the key once (the security in- dicator light will blink), and then insert the key in the ignition switch and turn it to the “START” position and again try to start the engine. NOTE The engine may not start in the follow- (cid:121) The key grip is touching another key or a metallic key holder. 300502 (cid:121) The key is near another key that con- tains an immobilizer transponder. 300503 A3120BE-B.book 5 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:132) Key reminder chime The reminder chime sounds when the driver’s door opens and the key is in the “LOCK” or “ACC” positions. The chime stops when the key is removed from the ignition switch. (cid:132) Ignition switch light For easy access to the ignition switch in the dark, the ignition switch light comes on when the driver’s door is opened. The light remains on for a several seconds and gradually goes out after the driver’s door is closed. Hazard warning flasher Meters and gauges Instruments and controls 3-5 NOTE Liquid-crystal displays are used in some of the meters and gauges in the combination meter. You will find their indications hard to see if you wear po- larized glasses. (cid:132) Combination meter illumina- tion When the ignition switch is turned to the “ON” position, the various parts of the combination meter are illuminated in the following sequence: 1. Warning lights, indicator lights, meter rims, meter needles, odometer, trip meter, and gauge back lights illuminate. 2. Meter needles and gauges each show MAX reading. 3. Meter needles and gauges each show MIN reading. 4. Meter and gauge dials illuminate. 5. Regular illumination (for driving) be- gins. – CONTINUED – 300504 The hazard warning flasher is used to warn other drivers when you have to park your vehicle under emergency conditions. The hazard warning flasher works with the ignition switch in any position. To turn on the hazard warning flasher, push the hazard warning button on the in- strument panel. To turn off the flasher, push the button again. NOTE When the hazard warning flasher is on, the turn signals do not work. A3120BE-B.book 6 ページ２００６年５月３０日　火曜日　午前９時３２分 3-6 Instruments and controls (cid:132) Canceling the function for meter needle/gauge move- ment and combination meter sequential illumination upon turning on the ignition switch change the current setting, press the trip knob for at least two seconds. change the current setting, press the trip knob for at least two seconds. : Activated : Deactivated : Activated : Deactivated With the function deactivated, the combi- nation meter illuminates as follows: 1. Warning lights, indicator lights, meter rims, meter needles, odometer, trip meter, and gauge back lights illuminate. 2. Meter and gauge dials illuminate. 3. Regular illumination (for driving) be- gins. Briefly press the knob to return to the A trip meter indication. If you turn the ignition switch to the “LOCK” position, turn the ignition switch to the “ON” position, or open and close the driver’s door during the setting procedure, the new setting will be canceled. Also, if you do not press the trip knob for a period of 10 seconds, the new setting will be canceled. NOTE (cid:121) It is not possible to cancel sequential illumination of the combination meter while sequential illumination is actual- ly taking place. Cancel sequential illu- mination when regular illumination (for driving) has begun. (cid:121) When you open the driver’s door with the ignition switch in the “LOCK” position, the meters’ needles and rims are lit. The illumination stops working when you shut the driver’s door or au- tomatically after 30 seconds. 300185 It is possible to activate or deactivate the movement of the meter needles and gauges and sequential illumination of the combination meter that takes place when the ignition switch is turned to the “ON” po- sition. Turn the ignition switch to the “ACC” posi- tion. With the A trip meter indication se- lected, briefly press the trip knob twice. You can now establish the activated/deac- tivated setting for movement of the meter needles and gauges when the ignition switch is turned to the “ON” position. To 300543 Briefly press the trip knob again. You can now establish the activated/deactivated setting for sequential illumination of the combination meter when ignition switch is turned to the “ON” position. To the A3120BE-B.book 7 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:132) Speedometer The speedometer shows speed. the vehicle you open and close the driver’s door with- in 10 seconds of illumination of the odom- eter/trip meter. (cid:132) Odometer (cid:132) Double trip meter A trip meter B trip meter Instruments and controls 3-7 300261 300258 This meter displays the odometer when the ignition switch is in the “LOCK”, “ACC” or “ON” position. The odometer shows the total distance that the vehicle has been driven. If you press the trip knob when the ignition switch is in the “LOCK” or “ACC” position, the odometer/trip meter will light up. If you do not press the trip knob within 10 sec- onds of illumination of the odometer/trip meter, the odometer/trip meter will go off. The odometer/trip meter will also go off if This meter display two trip meters when the ignition switch is in the “LOCK”, “ACC” or “ON” position. The trip meter shows the distance that the vehicle has been driven since you last set it to zero. To change the mode indication, briefly push the knob. Each press of the knob changes the mode indication alternately. To set the trip meter to zero, select the A trip or B trip meter by pushing the knob and keep the knob pushed for more than 2 seconds. If you press the trip knob when the ignition switch is in the “LOCK” position, the odometer/trip meter will light up. It is pos- sible to switch between the A trip meter and B trip meter indications while the odometer/trip meter is lit up. If you do not press the trip knob within 10 seconds of il- lumination of the odometer/trip meter, the odometer/trip meter will go off. Also, if you open and close the driver’s door within 10 seconds of illumination of the odometer/ trip meter, the odometer/trip meter will go off. To ensure safety, do not attempt to change the function of the indicator during driving, as an accident could result. – CONTINUED – A3120BE-B.book 8 ページ２００６年５月３０日　火曜日　午前９時３２分 3-8 Instruments and controls NOTE If the connection between the combi- nation meter and battery is broken for any reason such as vehicle mainte- nance or fuse replacement, the data re- corded on the trip meter will be lost. (cid:84) Vehicle communication system fault indication ”. The vehicle communication system car- ries various types of information (vehicle speed, running conditions, etc.) to control modules. In the event of a fault in this communication system, the trip meter will show “ If the trip meter shows “ ”, immedi- ately contact the nearest SUBARU dealer and have the vehicle communication sys- tem inspected. NOTE If you press the trip knob while the trip meter is showing “ ”, the trip meter indication will appear for 10 sec- onds. (cid:132) Tachometer The tachometer shows the engine speed in thousands of revolutions per minute. Do not operate the engine with the pointer of the tachometer in the red zone. In this range, fuel injection will be cut by the engine control module to protect the engine from overrev- ving. The engine will resume run- ning normally after the engine speed is reduced below the red zone. (cid:132) Fuel gauge amount of fuel remaining in the tank. The gauge may move slightly during brak- ing, turning or acceleration due to fuel lev- el movement in the tank. If you press the trip knob while the ignition switch is in the “LOCK” or “ACC” position, the fuel gauge will light up and indicate the amount of fuel remaining in the tank. If, while the fuel gauge is indicating the amount of fuel remaining in the tank, you (a) do not press the trip knob for 10 sec- onds or (b) open and close the driver’s door, the fuel gauge indication will go off. 200253 (cid:84) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty [Approximately 2.6 US gal (10 liters, 2.2 Imp gal)]. 300542 The fuel gauge shows the approximate A3120BE-B.book 9 ページ２００６年５月３０日　火曜日　午前９時３２分 It only operates when the ignition switch is in the “ON” position. NOTE This light does not go out unless the tank is replenished up to an internal fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal). We recommend that you drive moderately until the pointer of the temperature gauge reaches near the middle of the range. En- gine operation is optimum with the engine coolant at this temperature range and high revving operation when the engine is not warmed up enough should be avoided. (cid:132) Temperature gauge If the pointer exceeds the normal operating range, safely stop the ve- hicle as soon as possible. See the “In case of emergency” in chapter 9. 300541 1) Normal operating range The temperature gauge shows engine coolant temperature when the ignition switch is in the “ON” position. The coolant temperature will vary in ac- cordance with the outside temperature and driving conditions. Instruments and controls 3-9 Warning and indicator lights Several of the warning and indicator lights come on momentarily and then go out when the ignition switch is initially turned to the “ON” position. This permits check- ing the operation of the bulbs. Apply the parking brake and turn the igni- tion switch to the “ON” position. The fol- lowing lights come on: : Driver’s seatbelt warning light (The seatbelt warning light goes out only when the driver fastens the seatbelt.) : Front passenger’s seatbelt warn- ing light (The seatbelt warning light goes out only when the front seat passenger fastens the seatbelt.) : SRS airbag system warning light : CHECK ENGINE warning light/ Malfunction indicator lamp : Charge warning light : Oil pressure warning light : AT OIL temperature warning light – CONTINUED – A3120BE-B.book 10 ページ２００６年５月３０日　火曜日　午前９時３２分 3-10 Instruments and controls : ABS warning light : Vehicle Dynamics Control operation indicator light : Vehicle Dynamics Control warning light/Traction Control system OFF indica- tor light : Rear differential oil temperature warning light : Windshield washer fluid warning light : Door open warning light : Security indicator light : Brake system warning light : AWD warning light light : Daytime running light indicator : Low tire pressure warning light : SPORT mode indicator light : Front passenger’s frontal airbag ON indicator light : Front passenger’s frontal airbag OFF indicator light : Low fuel warning light : Cruise control indicator light : Cruise control set indicator light If any lights fail to come on, it indicates a burned-out bulb or a malfunction of the corresponding system. Consult your authorized SUBARU dealer for repair. (cid:132) Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver’s and front passenger’s seat. With the ignition switch turned to the “ON” position, this device reminds the driver and front passenger to fasten their seat- belts by illuminating the warning lights in the locations indicated in the following il- lustrations and sounding a chime. Driver’s warning light 100372 PASS 100373 Front passenger’s warning light (cid:84) Operation If the driver and/or front passenger have/ A3120BE-B.book 11 ページ２００６年５月３０日　火曜日　午前９時３２分 has not yet fastened the seatbelt(s) when the ignition switch is turned to the “ON” po- sition, the seatbelt warning light(s) will flash for 6 seconds, to warn that the seat- belt(s) is/are unfastened. If the driver’s seatbelt is not fastened, a chime will also sound simultaneously. If the driver’s and/or front passenger’s seatbelt(s) are/is still not fastened 6 sec- onds later, both warning lights or the warning light for the unfastened seatbelt will remain lit for 15 seconds. If the driver’s and/or front passenger’s seatbelt(s) are/is still not fastened even 15 seconds later (21 seconds after turning ON the ignition switch), the warning lights will alternate between flashing and steady illumination at 15-second intervals, and the chime will sound while the warning light(s) is/are flashing. Alternate flashing and steady illumination of the warning lights and sounding of the chime will continue until both driver and front passenger fasten their seatbelts. NOTE (cid:121) If the driver and/or front passenger unfasten(s) the seatbelt(s) after fasten- ing, the seatbelt warning device oper- ates as follows according to the vehi- cle speed. (cid:121) At speeds lower than approximate- ly 9 mph (15 km/h) The warning light(s) for unfastened seatbelt(s) will alternate between flashing and steady illumination at 15-second intervals. The chime will not sound. (cid:121) At speeds higher than approxi- mately 9 mph (15 km/h) The warning light(s) for unfastened seatbelt(s) will alternate between flashing and steady illumination at 15-second intervals and the chime will sound while the warning light(s) is/are flashing. (cid:121) It is possible to cancel the warning operation that follows the 6-second warning after turning ON the ignition switch. When the ignition switch is turned ON next time, however, the complete sequence of the warning op- eration resumes. For further details about canceling the warning operation, please contact your SUBARU dealer. If there is no passenger on the front pas- senger’s seat, the seatbelt warning device for the front passenger’s seat will be deac- tivated. The front passenger’s occupant detection system monitors whether or not there is a passenger on the front passen- ger’s seat. Observe the following precau- tions. Failure to do so may prevent the de- vice from functioning correctly or cause the device to fail. Instruments and controls 3-11 (cid:121) Do not install any accessory such as a table or TV onto the seatback. (cid:121) Do not store a heavy load in the seat- back pocket. (cid:121) Do not allow the rear seat occupant to place his/her hands or legs on the front passenger’s seatback, or allow him/her to pull the seatback. If the seatbelt warning device for the front passenger’s seat does not function cor- rectly (e.g., it is activated even when the front passenger’s seat is empty or it is de- activated even when the front passenger has not fastened his/her seatbelt), take the following actions. (cid:121) Ensure that no article is placed on the seat other than a child restraint system and its child occupant. (cid:121) Ensure that there is no article left in the seatback pocket. If still the seatbelt warning device for front passenger’s seat does not function cor- rectly after taking relevant corrective ac- tions described above, immediately con- tact your SUBARU dealer for an inspec- tion. (cid:132) SRS airbag system warn- ing light When the ignition switch is turned to the – CONTINUED – A3120BE-B.book 12 ページ２００６年５月３０日　火曜日　午前９時３２分 3-12 Instruments and controls “ON” position, the SRS airbag system warning light will come on for approxi- mately 6 seconds and go out. This shows the SRS frontal airbag and SRS side air- bag and SRS curtain airbag and seatbelt pretensioners are in normal operation. (cid:121) Illumination of the warning light while driving (cid:132) Front passenger’s frontal air- bag ON and OFF indicators If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pre- tensioners and/or SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g. SRS airbags may inflate in a very mi- nor collision or not inflate in a se- vere collision), which may increase the risk of injury. (cid:121) Flashing or flickering of the warn- ing light (cid:121) No illumination of the warning light when the ignition switch is first turned to the “ON” position (cid:121) Continuous illumination of the warning light PASS AIR BAG 100533 : Front passenger’s frontal airbag : Front passenger’s frontal airbag ON indicator OFF indicator The front passenger’s frontal airbag ON and OFF indicators show you the status of the front passenger’s SRS frontal airbag. The indicators are located in the center portion of the dashboard. When the ignition switch is turned to the “ON” position, both the ON and OFF indi- cators illuminate for 6 seconds during which time the system is checked. Follow- ing the system check, both indicators ex- tinguish for 2 seconds. After that, one of the indicators illuminates depending on the status of the front passenger’s SRS frontal airbag determined by the Subaru advanced frontal airbag system monitor- ing. If the front passenger’s SRS frontal airbag is activated, the passenger’s frontal airbag ON indicator will illuminate while the OFF indicator will remain extinguished. If the front passenger’s SRS frontal airbag is deactivated, the passenger’s frontal air- bag ON indicator will remain extinguished while the OFF indicator will illuminate. If both the ON and OFF indicators remain lit or extinguished simultaneously, the sys- tem is faulty. Contact your SUBARU deal- er immediately for an inspection. A3120BE-B.book 13 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:132) CHECK ENGINE warn- ing light/Malfunction in- dicator lamp If the CHECK ENGINE light comes on while you are driving, have your vehicle checked/repaired by your SUBARU dealer as soon as possi- ble. Continued vehicle operation without having the emission control system checked and repaired as necessary could cause serious damage, which may not be covered by your vehicle’s warranty. If this light comes on steadily or blinks while the engine is running, it may indicate that there is a problem or potential prob- lem somewhere in the emission control system. (cid:84) If the light comes on steadily: If the light comes on steadily while driving or does not go out after the engine starts, an emission control system malfunction has been detected. You should have your vehicle checked by an authorized SUBARU dealer immedi- ately. NOTE This light also comes on when the fuel filler cap is not tightened until it clicks. If you have recently refueled your vehicle, the cause of the CHECK ENGINE warning light/malfunction indicator lamp coming on could be a loose or missing fuel filler cap. Remove the cap and retighten it until it clicks. Make sure nothing is interfering with the sealing of the cap. Tightening the cap will not make the CHECK ENGINE warning light turn off immediately. It may take several driving trips. If the light does not go out, take your vehicle to your au- thorized SUBARU dealer immediately. (cid:84) If the light is blinking: If the light is blinking while driving, an en- gine misfire condition has been detected which may damage the emission control system. To prevent serious damage to the emis- sion control system, you should do the fol- lowing. (cid:121) Reduce vehicle speed. (cid:121) Avoid hard acceleration. (cid:121) Avoid steep uphill grades. (cid:121) Reduce the amount of cargo, if possi- ble. (cid:121) Stop towing a trailer as soon as possi- ble. Instruments and controls 3-13 The CHECK ENGINE warning light may stop blinking and come on steadily after several driving trips. You should have your vehicle checked by an authorized SUBARU dealer immediately. (cid:132) Charge warning light If this light comes on when the engine is running, it may indicate that the charging system is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the alternator belt. If the belt is loose, broken or if the belt is in good con- dition but the light remains on, contact your nearest SUBARU dealer immediate- ly. (cid:132) Oil pressure warning light Do not operate the engine with the oil pressure warning light on. This may cause serious engine damage. If this light comes on when the engine is running, it may indicate that the engine oil pressure is low and the lubricating system – CONTINUED – A3120BE-B.book 14 ページ２００６年５月３０日　火曜日　午前９時３２分 3-14 Instruments and controls is not working properly. If the light comes on while driving or does not go out after the engine starts, stop the engine at the first safe opportunity and check the engine oil level. If the oil level is low, add oil immediately. If the engine oil is at the proper level but the light remains on, contact your nearest SUBARU dealer immediately. (cid:132) AT OIL TEMPerature warning light The AT oil temperature warning light comes on when the ignition switch is turned to the “ON” position and goes out after approximately 2 seconds. If this light comes on when the engine is running, it may indicate that the automatic transmission fluid temperature is too hot. If the light comes on while driving, it is un- necessary to stop the vehicle, but avoid driving up steep grades or in stop and go traffic. (cid:132) Rear differential oil tem- perature warning light Reduce vehicle speed and park the vehicle in a safe place as soon as possible if the R.DIFF TEMP light comes on. Continued driving with this light on can damage the rear dif- ferential and other parts of the pow- ertrain. If this light comes on when the engine is running, it may indicate that the rear differ- ential oil temperature is too hot. If the light comes on while driving, reduce vehicle speed and stop the vehicle at the nearest safe place. Park the vehicle for several minutes. After the light goes out, you can start driving. If the light does not go out, contact the nearest SUBARU dealer for service. NOTE (cid:121) If the tire pressures are not correct and/or the tires are not all the same size and brand, the rear differential will be heavily loaded when the vehicle is driven, resulting in an abnormally high oil temperature. (cid:121) The rear differential oil will deterio- if its temperature rate increases enough for the rear differential oil tem- perature warning light to come on. It is advisable to have the rear differential oil replaced as soon as possible. (cid:132) Low tire pressure warn- ing light When the ignition switch is turned to the “ON” position, the low tire pressure warn- ing light will come on for approximately 2 seconds to check that the tire pressure monitoring system (TPMS) is functioning properly. If there is no problem and all tires are properly inflated, the light will go out. Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure rec- ommended by the vehicle manufacturer on the vehicle placard or tire inflation pres- sure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard or tire inflation pres- sure label, you should determine the prop- er inflation pressure for those tires.) As an added safety feature, your vehicle has been equipped with a tire pressure moni- toring system (TPMS) that illuminates a low tire pressure telltale when one or more of your tires is significantly under-inflated. Accordingly, when the low tire pressure A3120BE-B.book 15 ページ２００６年５月３０日　火曜日　午前９時３２分 telltale illuminates, you should stop and check your tires as soon as possible, and inflate them to the proper pressure. Driv- ing on a significantly under-inflated tire causes the tire to overheat and can lead to tire failure. Under-inflation also reduces fuel efficiency and tire tread life, and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to main- tain correct tire pressure, even if under-in- flation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. The TPMS gives warning both when a tire is significantly under-inflated and when there is a problem in the TPMS. The low tire pressure warning light operates differ- ently according to these conditions as fol- lows: When a tire is significantly under-inflat- ed: Steady illumination When there is a problem in the TPMS: Flashing Should the warning light flash, have the system inspected by your nearest SUBA- RU dealer as soon as possible. If this light does not come on briefly after the ignition switch is turned ON or the light is flashing, you should have your Tire Pressure Monitoring System checked at a SUBARU dealer as soon as possi- ble. If this light comes on while driving, never brake suddenly and keep driv- ing straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place. Otherwise an accident involving serious vehi- cle damage and serious personal in- jury could occur. If this light still comes on while driv- ing after adjusting the tire pressure, a tire may have significant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible. Instruments and controls 3-15 When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the Low tire pres- sure warning light will flash. This in- dicates the TPMS is unable to moni- tor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replace- ment and/or system resetting. If the light flashes, promptly contact a SUBARU dealer to have the system inspected. The tire pressure monitoring system is NOT a substitute for manually checking tire pressure. The tire pressure should be checked period- ically (at least monthly) using a tire gauge. After any change to tire pres- sure(s), the tire pressure monitoring system will not re-check tire infla- tion pressures until the vehicle is first driven more than 20 mph (32 km/h). Be sure to install the speci- fied size for the front and rear tires. – CONTINUED – A3120BE-B.book 16 ページ２００６年５月３０日　火曜日　午前９時３２分 3-16 Instruments and controls (cid:132) ABS warning light (U.S.) (Canada) The ABS warning light comes on when the ignition switch is turned to the “ON” posi- tion and goes out after approximately 2 seconds. This is an indication that the ABS system is working properly. If the warning light behaves as fol- lows, the ABS system may not work properly. When the warning light is on, the ABS function shuts down; however, the conventional brake system con- tinues to operate normally. (cid:121) The warning light does not come on when the ignition switch is turned to the “ON” position. (cid:121) The warning light comes on when the ignition switch is turned to the “ON” position, but it does not go out even when the vehicle speed exceeds approximately 8 mph (12 km/h). (cid:121) The warning light comes on dur- ing driving. If any of these conditions occur, have the ABS system repaired at the first available opportunity by your SUBARU dealer. The ABS warning light comes on together with the brake system warning light if the EBD system becomes faulty. For further details of the EBD system fault warning, refer to “Brake system warning light”. NOTE If the warning light behavior is as de- scribed in the following, the ABS sys- tem may be considered normal. (cid:121) The warning light comes on right af- ter the engine is started but goes out immediately, remaining off. (cid:121) The warning light remains on after the engine has been started, but it goes out when the vehicle speed reaches approximately 8 mph (12 km/h). (cid:121) The warning light comes on during driving, but it goes out immediately and remains off. When driving with an insufficient battery voltage such as when the engine is jump started, the ABS warning light may come on. This is due to the low battery voltage and does not indicate a malfunction. When the battery becomes fully charged, the light will go out. (cid:132) Brake system warning light (U.S.) (Canada) (cid:121) Driving with the brake system warning light on is dangerous. This indicates your brake system may not be working properly. If the light remains on, have the brakes inspected by a SUBARU dealer immediately. (cid:121) If at all in doubt about whether the brakes are operating properly, do not drive the vehicle. Have your vehicle the nearest SUBARU dealer for repair. towed to This light has the following three func- tions: (cid:84) Parking brake warning The light comes on with the parking brake applied while the ignition switch is in the “ON” position. It goes out when the park- ing brake is fully released. (cid:84) Brake fluid level warning This light comes on when the brake fluid level has dropped to near the “MIN” level of the brake fluid reservoir with the ignition switch in the “ON” position and with the A3120BE-B.book 17 ページ２００６年５月３０日　火曜日　午前９時３２分 parking brake fully released. If the brake system warning light should come on while driving (with the parking brake fully released and with the ignition switch positioned in “ON”), it could be an indication of leaking of brake fluid or worn brake pads. If this occurs, immediately stop the vehicle at the nearest safe place and check the brake fluid level. If the fluid level is below the “MIN” mark in the reser- voir, do not drive the vehicle. Have the ve- hicle towed to the nearest SUBARU deal- er for repair. (cid:84) Electronic Brake Force Distribution (EBD) system warning The brake system warning light also illu- minates if a malfunction occurs in the EBD system. In that event, it comes on together with the ABS warning light. The EBD system may be faulty if the brake system warning light and ABS warning light illuminate simultaneously during driv- ing. Even if the EBD system fails, the conven- tional braking system will still function. However, the rear wheels will be more prone to locking when the brakes are ap- plied harder than usual and the vehicle’s motion may therefore become somewhat harder to control. If the brake system warning light and ABS warning light illuminate simultaneously, take the following steps: 1. Stop the vehicle in the nearest safe, flat place. 2. Shut down the engine, apply the park- ing brake, and then restart it. 3. Release the parking brake. If both warning lights go out, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system inspected. 4. If both warning lights come on again and stay illuminated after the engine has been restarted, shut down the engine again, apply the parking brake, and check the brake fluid level. 5. If the brake fluid level is not below the “MIN” mark, the EBD system may be faulty. Drive carefully to the nearest SUBARU dealer and have the system in- spected. 6. If the brake fluid level is below the “MIN” mark, DO NOT drive the vehicle. In- stead, have the vehicle towed to the near- est SUBARU dealer for repair. (cid:132) Low fuel warning light The low fuel warning light comes on when the tank is nearly empty approximately 2.6 US gal (10 liters, or 2.2 Imp gal). It only op- erates when the ignition switch is in the “ON” position. Instruments and controls 3-17 NOTE This light does not go out unless the tank is replenished up to an internal fuel quantity of approximately 4.0 US gal (15 liters, 3.3 Imp gal). (cid:132) Door open warning light 300505 The indicators are located in the center portion of the dashboard. When any of the doors or the rear gate is not fully closed, it is indicated by the corre- sponding part of the door warning light. Always make sure this light is out before you start to drive. – CONTINUED – A3120BE-B.book 18 ページ２００６年５月３０日　火曜日　午前９時３２分 3-18 Instruments and controls (cid:132) Windshield washer fluid warning light This light comes on when the fluid level in the windshield washer fluid tank falls to the lower limit (approximately 0.6 US qt, 0.6 liter, 0.5 Imp qt). (cid:132) All-Wheel Drive warn- ing light Continued driving with the AWD warning light flashing can lead to powertrain damage. If the AWD warning light flashes, promptly park in a safe place then check whether all four tires are the same diameter and whether any of the tires has a puncture or has lost air pressure for some other reason. The All-Wheel Drive warning light comes on when the ignition switch is turned to the “ON” position and goes out after the en- gine has started. This light flashes if the vehicle is driven with tires of different diameters fitted on its wheels or with the air pressure excessive- ly low in any of its tires. (cid:132) Vehicle Dynamics Con- trol operation indicator light This light comes on when the ignition switch is ON and goes out approximately 2 seconds later. It blinks when the skid suppression func- tion is activated. It illuminates when only the traction control function is operating. The Vehicle Dynamics Control system is probably faulty under any of the following conditions. Have your vehicle checked at a SUBARU dealer immediately. (cid:121) The light does not come on when the ig- nition switch is turned to the “ON” position. (cid:121) The light does not go out even after a period of approximately 2 seconds after the ignition switch has been turned to the “ON” position. (cid:132) Vehicle Dynamics Con- trol warning light/Trac- tion Control system OFF indicator light This warning light has both the function of indicating faults in the Vehicle Dynamics Control system and the function of indicat- ing that the Traction Control system has been deactivated. It comes on in the event of a fault in the system and is on when the system is not operating. This warning light comes on when the ig- nition switch is turned to the “ON” position and goes out after the engine has started. It indicates that the Vehicle Dynamics Control system is in normal operation. (cid:84) Vehicle Dynamics Control warning light The Vehicle Dynamics Control system is probably inoperative under any of the fol- lowing conditions. Have your vehicle checked at a SUBARU dealer immediate- ly. (cid:121) The warning light does not come on when the ignition switch is turned to the “ON” position. (cid:121) The warning light comes on while the vehicle is running. (cid:121) If the electrical circuit of the Vehicle Dy- namics Control system itself becomes faulty, the warning light only comes on. At this time, the ABS (Anti-lock Brake Sys- tem) remains fully operational. (cid:121) The warning light comes on when the electronic control system of the ABS/Vehi- cle Dynamics Control system becomes faulty. The Vehicle Dynamics Control system provides its ABS control through the elec- trical circuit of the ABS system. Accord- A3120BE-B.book 19 ページ２００６年５月３０日　火曜日　午前９時３２分 (cid:121) It also comes on when the Traction Control system is deactivated. NOTE (cid:121) The light may stay on for a while after the engine has been started, especially in cold weather. This does not indicate the existence of a problem. The light should go out as soon as the engine has warmed up. (cid:121) The indicator light comes on when the engine has developed a problem and the CHECK ENGINE warning light/ Malfunction indicator lamp is on. The Vehicle Dynamics Control system is probably faulty under the following condi- tion. Have your vehicle checked at a SUBARU dealer as soon as possible. (cid:121) The light does not go out even after the lapse of several minutes (the engine has warmed up) after the engine has started. ingly, if the ABS is inoperative, the Vehicle Dynamics Control system becomes un- able to provide ABS control. As a result, the Vehicle Dynamics Control system also becomes inoperative, causing the warning light to come on. Though both the Vehicle Dynamics Control and ABS systems are inoperative in this case, the ordinary func- tions of the brake system are still avail- able. You will be safe while driving with this condition, but have your vehicle checked at a SUBARU dealer as soon as possible. NOTE If the warning light behavior is as shown in the following, the Vehicle Dy- namics Control system may be consid- ered normal. (cid:121) The warning light comes on right af- ter the engine is started but goes out immediately, remaining off. (cid:121) The warning light comes on after en- gine startup and goes off while the ve- hicle is subsequently being driven. (cid:121) The warning light comes on during driving, but it goes out immediately and remains off. (cid:84) Traction Control system OFF indica- tor light (cid:121) It comes on when the Traction Control system OFF switch is pressed. Instruments and controls 3-19 (cid:132) Security indicator light 200702 The indicators are located in the center portion of the dashboard. This indicator light shows the status of the alarm system. It also indicates operation of the immobilizer system. (cid:84) Alarm system It blinks to show the driver the operational status of the alarm system. For detailed information, refer to the “Alarm system” section in chapter 2. (cid:84) Immobilizer system This light blinks approximately 60 seconds after the ignition switch is turned from “ON” position to the “ACC” or “LOCK” po- sition or immediately after the key is pulled out. (Refer to the “Door locks” section in – CONTINUED – A3120BE-B.book 20 ページ２００６年５月３０日　火曜日　午前９時３２分 3-20 Instruments and controls chapter 2.) If the indicator light does not flash, it may indicate that immobilizer system may be faulty. Contact your nearest SUBARU dealer immediately. In the event that an unauthorized key (for example, an unauthorized duplicate) is used, the security indicator light comes on. (cid:132) SPORT mode indicator light This light comes on when the ignition switch is turned to the “ON” position and goes out after the engine has started. When the selector lever is moved to the manual gate, the SPORT mode is select- ed and the indicator light comes on. (Refer to the “Automatic transmission” section in chapter 7.) (cid:84) Automatic transmission control system warning If the light flashes after the engine starts, it may indicate that the automatic trans- mission control system is not working properly. Contact your nearest SUBARU dealer for service immediately. (cid:132) Selector lever/Gear position indicator possible. Refer to the “Replacing bulbs” section in chapter 11. (cid:132) High beam indicator light This light shows that the headlights are in the high beam mode. This indicator light also comes on when the headlight flasher is operated. (cid:132) Cruise control indica- tor light The cruise control indicator light comes on when the ignition switch is turned to the “ON” position and goes out after approxi- mately 3 seconds. This light comes on when the “CRUISE” main switch is pressed. NOTE If you move the cruise control lever or press the main switch button while turning the ignition switch “ON”, the cruise control function is deactivated and the “CRUISE” indicator light flash- es. To reactivate the cruise control function, turn the ignition switch back to the “ACC” or “LOCK” position, and then turn it again to the “ON” position. 300266 The selector lever/gear position indicator shows the position of the selector lever. When manual mode is selected, the gear position indicator shows the current gear position and the upshift/downshift indica- tor illuminates. (Refer to the “Automatic transmission” section in chapter 7.) (cid:132) Turn signal indicator lights These lights show the operation of the turn signal or lane change signal. If the indicator lights do not blink or blink rapidly, the turn signal bulb may be burned out. Replace the bulb as soon as A3120BE-B.book 21 ページ２００６年５月３０日　火曜日　午前９時３２分 Clock NOTE If your vehicle is equipped with a navi- gation system, refer to the separate “Operating Instructions for Monitor System”. CLOCK 300603 The clock shows the time while the igni- tion switch is in the “ACC” or “ON” posi- tion. (cid:132) Cruise control set indica- tor light The cruise control set indicator light comes on when the ignition switch is turned to the “ON” position and goes out after approximately 3 seconds. This light comes on when vehicle speed has been set. (cid:132) Headlight indicator light This indicator light comes on when the light switch is turned to the “ ” posi- tion (to turn on the parking lights) or to the “ ” position (to turn on the headlights). (cid:132) Front fog light indicator light This indicator light is on while the front fog lights are on. (cid:132) Daytime running light indicator light (U.S.) (Canada) The daytime running light indicator light comes on when the daytime running light system is operating. Refer to the “Light control switch” section in this chapter. Instruments and controls 3-21 300602 If you keep To adjust the time shown by the clock, press the “+” button or the “–” button. The indicated time will change in one-minute increments. the button pressed, the rate at which the indicated time changes will speed up. When you keep either the “+” or “– “ button pressed, time change will pause for 1 sec- ond at the end of each 30-minute change. The clock will start going forward or back- ward again quickly after this 1-second pause. To ensure safety, do not attempt to set the time during driving, as an ac- cident could result. A3120BE-B.book 22 ページ２００６年５月３０日　火曜日　午前９時３２分 3-22 Instruments and controls Outside temperature indica- tor NOTE If your vehicle is equipped with a navi- gation system, refer to the separate “Operating Instructions for Monitor System”. U.S.-spec. vehicles 300550 300551 Canada-spec. vehicles The outside temperature indicator shows the outside temperature in a range from –22 to 122°F (–30 to 50°C). The indicator can give a false reading un- der any of the following conditions: (cid:121) When there is too much sun. (cid:121) During idling; while running at low speeds in a traffic jam; when the engine is restarted immediately following a shut- down. (cid:121) When the actual outside temperature falls outside the specified indicator range. (cid:84) Low outside temperature warning U.S.-spec. vehicles 300552 300553 Canada-spec. vehicles When the outside temperature drops to A3120BE-B.book 23 ページ２００６年５月３０日　火曜日　午前９時３２分 37°F (3°C) or lower, the temperature indi- cation flashes to show that the road sur- face may be frozen. If the outside temperature drops to 37°F (3°C) or lower while the display is giving an indication other than the outside tem- perature, the display switches to the out- side temperature indication and flashes for five seconds before returning to its original indication. If the display is already indicating an out- side temperature of 37°F (3°C) or lower when the ignition switch is turned to the “ON” position, the indication does not flash. NOTE The outside temperature indication may differ from the actual outside tem- perature. The road surface freeze warn- ing indication should be treated only as a guide. Be sure to check the condi- tion of the road surface before driving. Multi function display (Vehi- cle without Navigation Sys- tem) NOTE (cid:121) If your vehicle is equipped with a navigation system, refer to the sepa- rate “Operating Instructions for Moni- tor System”. (cid:121) A liquid-crystal display is used in the multi function display. You will find its indications hard to see if you wear po- larized glasses. With the ignition switch in the “ON” posi- tion, each successive push of the “INFO” button toggles the display in the following sequence: Current fuel con- sumption Journey time Average fuel con- sumption Driving range on remaining fuel Press the “INFO” button for more than 1 second to turn off the display. The display will turn on again if you press either the “INFO” button or “AUDIO” button. Instruments and controls 3-23 (cid:132) Current fuel consumption U.S.-spec. vehicles 300554 300555 Canada-spec. vehicles This indication shows the rate of fuel con- – CONTINUED – A3120BE-B.book 24 ページ２００６年５月３０日　火曜日　午前９時３２分 3-24 Instruments and controls sumption at the present moment. (cid:132) Average fuel consumption U.S.-spec. vehicles 300556 300791 Canada-spec. vehicles This indication shows the average rate of fuel consumption since the trip meter was last reset. Pressing the trip knob toggles the indica- tion between the average fuel consump- tion corresponding to the A trip meter indi- cation and the average fuel consumption corresponding to the B trip meter indica- tion. When either of the trip meter indications is reset, the corresponding average fuel consumption value is also reset. NOTE (cid:121) The indicated values vary in accor- dance with changes in the vehicle’s running conditions. Also, the indicated values may differ slightly from the ac- tual values and should thus be treated only as a guide. (cid:121) When either trip meter indication is reset, the average fuel consumption corresponding to that trip meter indica- tion is not shown until the vehicle has subsequently covered a distance of 1 mile (or 1 km). (cid:132) Driving range on remaining fuel U.S.-spec. vehicles 300558 A3120BE-B.book 25 ページ２００６年５月３０日　火曜日　午前９時３２分 Canada-spec. vehicles U.S.-spec. vehicles 300559 300560 The driving range indicates the distance that can be driven taking into account the amount of fuel remaining in the tank and the average rate of fuel consumption. When the low fuel warning light comes on, the driving range indication flashes for five seconds. (The display first switches to the driving range indication if it was originally giving some other indication.) Instruments and controls 3-25 tank. You must refuel the vehicle immedi- ately. NOTE (cid:121) The driving range on remaining fuel is only a guide. The indicated value may differ from the actual driving range on remaining fuel, so you must immediately fill the tank when the low fuel warning light comes on. (cid:121) When the low fuel warning light is lit, the display automatically shows “ ” even if the currently selected indication is not for the driving range on remaining fuel. (cid:132) Journey time 300561 Canada-spec. vehicles If the driving range is shown as “ ”, there is only a tiny amount of fuel left in the 300562 The journey time shows the time that has elapsed since the ignition switch was – CONTINUED – A3120BE-B.book 26 ページ２００６年５月３０日　火曜日　午前９時３２分

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2007 Subaru Tribeca Owners Manual