2007 Subaru Tribeca Owners Manual

(cid:132) Warranties and maintenance SUBARU warranties do not apply to vehi- cle damage or malfunction caused by trail- er towing. If you use your vehicle to tow a trailer, more frequent maintenance will be required due to the additional load. (Refer to “Maintenance schedule under severe driving conditions” in the “Warranty and Maintenance Booklet”.) Under no circumstances should a trailer be towed with a new vehicle or a vehicle with any new powertrain component (en- gine, transmission, differential, wheel bearings, etc.) for the first 1,000 miles (1,600 km) of driving.

Driving tips 8-17

(cid:132) Maximum load limits

Never exceed the maximum load limits explained in the following. Ex- ceeding the maximum load limits could cause personal injury and/or vehicle damage.

(cid:121) Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight.

(cid:121) Before towing a trailer, check the trailer total weight, GVW, GAWs and tongue load. Make sure the load and its distribution in your vehicle and trailer are acceptable.

Trailer towing

Your vehicle is designed and intended to be used primarily as a passenger-carrying vehicle. Towing a trailer puts additional loads on your vehicle’s engine, drivetrain, brakes, tires and suspension and has an adverse effect on fuel economy. If you do decide to tow a trailer, your safe- ty and satisfaction depend upon proper use of correct equipment and cautious op- eration of your vehicle. Seek the advice of your SUBARU dealer to assist you in pur- chasing a hitch and other necessary tow- ing equipment appropriate for your vehi- cle. In addition, be sure to follow the in- structions on correct installation and use provided by the trailer and other towing equipment manufacturers. SUBARU assumes no responsibility for in- juries or vehicle damage that result from trailer towing equipment, or from any er- rors or omissions in the instructions ac- companying such equipment or for your failure to follow the proper instructions.

– CONTINUED –

A3120BE-B.book 18 ページ ２００６年５月３０日　火曜日　午前９時３２分

8-18 Driving tips

(cid:84) Total trailer weight

800211

Total trailer weight

The total trailer weight (trailer weight plus its cargo load) must never exceed the maximum weight shown in the following table.

A3120BE-B.book 19 ページ ２００６年５月３０日　火曜日　午前９時３２分

Vehicle without cooling kit

Conditions

Maximum total trailer weight

When towing a trailer without brakes.

When towing a trailer with brakes.

When towing a trailer on a long uphill grade con- tinuously for over 5 miles (8 km) with an outside temperature of 104°F (40°C) or above.

Vehicle with cooling kit

1,000 lbs (453 kg)

2,000 lbs (906 kg)

1,000 lbs (453 kg)

Conditions

Maximum total trailer weight

When towing a trailer without brakes.

When towing a trailer with brakes.

When towing a trailer on a long uphill grade con- tinuously for over 5 miles (8 km) with an outside temperature of 104°F (40°C) or above.

1,000 lbs (453 kg)

3,500 lbs (1,587 kg)

1,750 lbs (794 kg)

Driving tips 8-19

(cid:84) Gross Vehicle Weight (GVW) and

Gross Vehicle Weight Rating (GVWR)

800212

Gross Vehicle Weight

The Gross Vehicle Weight (GVW) must never exceed the Gross Vehicle Weight Rating (GVWR). Gross Vehicle Weight (GVW) is the com- bined total of the weight of the vehicle, driver, passengers, luggage, trailer hitch, trailer tongue load and any other optional equipment installed on your vehicle. Therefore, the GVW changes depending on the situation. Determine the GVW each time before going on a trip by putting your vehicle and trailer on a vehicle scale. GVWR is shown on the certification label located on the driver’s door of your vehi-

– CONTINUED –

A3120BE-B.book 20 ページ ２００６年５月３０日　火曜日　午前９時３２分

8-20 Driving tips

cle.

The total weight applied to each axle (GAW) must never exceed the Gross Axle Weight Rating (GAWR). The front and rear GAWs can be adjusted by relocating passengers and luggage inside the vehi- cle. The front and rear GAWR are also shown on the certification label.

(cid:84) Tongue load

800203

Certification label

(cid:84) Gross Axle Weight (GAW) and

Gross Axle Weight Rating (GAWR)

Gross Axle Weight

800213

Tongue load

800214

800203

Certification label

To check both GVWR and GAWR and to confirm that the total weight and weight distribution are within safe driving limits, you should have your vehicle and trailer weighed at a commercial weighing sta- tion. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.

If the trailer is loaded with more weight in the back of trailer’s axle than in the front, the load is taken off the rear axle of the towing vehicle. This may cause the rear wheels to skid, especially during braking or when vehicle speed is reduced dur- ing cornering, resulting in over- steer, spin out and/or jackknifing.

Ensure that the trailer tongue load is from 8 to 11 percent of the total trailer weight and does not exceed the appropriate one of the following maximum values:

A3120BE-B.book 21 ページ ２００６年５月３０日　火曜日　午前９時３２分

Vehicle without cooling kit: 200 lbs (90 kg) Vehicle with cooling kit: 350 lbs (158 kg)

60%

40%

50% 50%

800215

F: Front

800216

1) Jack 2) Bathroom scale

The tongue load can be weighed with a bathroom scale as shown in the illustra- tion above. When weighing the tongue load, be sure to position the towing cou- pler at the height at which it would be dur- ing actual towing, using a jack as shown.

The tongue load can be adjusted by prop- er distribution of the load in the trailer. Never load the trailer with more weight in the back than in the front; approximately 60 percent of the trailer load should be in the front and approximately 40 percent in the rear. Also, distribute the load as even- ly as possible on both the left and right sides. Be sure that all cargo is firmly secured to prevent a change in weight distribution while driving.

Driving tips 8-21

(cid:132) Trailer hitches

Never drill the frame or under-body of your vehicle to install a commer- cial trailer hitch. If you do, danger- ous exhaust gas, water or mud may enter the passenger compartment through the drilled hole. Exhaust gas contains carbon monoxide, a colorless and odorless gas which is dangerous, or even lethal, if inhaled. Also, drilling the frame or under- body of your vehicle could cause deterioration of strength of your ve- hicle and cause corrosion around the drilled hole.

(cid:121) Do not modify the vehicle exhaust system, brake system, or other systems when installing a hitch or other trailer towing equipment.

(cid:121) Do not use axle-mounted hitches as they can cause damage to the axle housing, wheel bearings, wheels or tires.

Choose a proper hitch for your vehicle and trailer.

– CONTINUED –

A3120BE-B.book 22 ページ ２００６年５月３０日　火曜日　午前９時３２分

8-22 Driving tips

is

The use of a genuine SUBARU trailer hitch recommended. A genuine SUBARU hitch is available from your SUBARU dealer. If use of a non-genuine hitch is unavoid- able, be sure the hitch is suited to your ve- hicle and trailer. Consult with a profes- sional hitch supplier to assist you in choosing an appropriate hitch for your ve- hicle. Be sure to follow all of the hitch man- ufacturer’s instructions for installation and use. Never use a hitch that mounts only to the rear bumper. The bumper is not designed to handle that type of load. For all types of hitches, regularly check that the hitch mounting bolts and nuts are tight.

(cid:132) Connecting a trailer (cid:84) Trailer brakes

(cid:84) Trailer safety chains

(cid:121) Adequate size trailer brakes are required when the trailer and its cargo exceed 1,000 lbs (453 kg) total weight.

(cid:121) Do not directly connect your trail- er’s hydraulic brake system to the hydraulic brake system in your vehicle. Direct connection would cause the vehicle’s brake perfor- mance to deteriorate and could lead to an accident.

If your trailer’s total weight (trailer weight plus its cargo weight) exceeds 1,000 lbs (453 kg), the trailer is required to be equipped with its own brake system. Elec- tric brakes or surge brakes are recom- mended, and must be installed properly. Check that your trailer’s brakes conform with Federal, state/province and/or other applicable regulations. Your SUBARU’s brake system is not designed to be tapped into the trailer’s hydraulic brake system. Please ask your SUBARU dealer and pro- fessional trailer supplier for more informa- tion about the trailer’s brake system.

Always use safety chains between your vehicle and the trailer. Towing trailer without safety chains could create a traffic safety hazard if the trailer separates from the hitch due to coupling damage or hitch ball damage.

In case the trailer hitch connector or hitch ball should break or become disconnect- ed, the trailer could get loose and create a traffic safety hazard. For safety, always connect the towing ve- hicle and trailer with trailer safety chains. Pass the chains crossing each other un- der the trailer tongue to prevent the trailer from dropping onto the ground in case the trailer tongue should disconnect from the hitch ball. Allow sufficient slack in the chains taking tight-turn situations into ac- count; however, be careful not to let them drag on the ground. For more information about the safety chain connection, refer to the instructions for your hitch and trailer.

A3120BE-B.book 23 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:84) Side mirrors

Connection of trailer lights to your vehi- cle’s electrical system requires modifica- tions to the vehicle’s lighting circuit to in- crease its capacity and accommodate wir- ing changes. To ensure the trailer lights are connected properly, please consult your SUBARU dealer. Check for proper operation of the turn signals, the brake lights and parking lights each time you hitch up.

(cid:84) Tires

800018

After hitching a trailer to your vehicle, check that the standard side mirrors pro- vide a good rearward field of view without significant blind spots. If significant blind spots occur with the vehicle’s standard side mirrors, use towing mirrors that con- form with Federal, state/province and/or other applicable regulations. (cid:84) Trailer lights

Direct splicing or other improper connection of trailer lights may damage your vehicle’s electrical system and cause a malfunction of your vehicle’s lighting system.

Never tow a trailer when the tempo- rary spare tire is used. The tempo- rary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle.

Make sure that all the tires on your vehicle are properly inflated.

The recommended cold tire pressure un- der trailer towing conditions is shown in chapter 12, “Specifications” and in “GAS STATION REFERENCE” at the end of this manual. Adjust the rear tire pressure to the recommended pressure when the tires are cold. Normal pressure should be

Driving tips 8-23

maintained in the front tires.

Trailer tire condition, size, load rating and proper inflation pressure should be in ac- cordance with the trailer manufacturer’s specifications.

In the event your vehicle gets a flat tire when towing a trailer, ask a commercial road service to repair the flat tire.

If you carry a regular size spare tire in your vehicle or trailer as a precaution against getting a flat tire, be sure that the spare tire is firmly secured.

(cid:132) Trailer towing tips

(cid:121) Never exceed 45 mph (72 km/h) when towing a trailer in hilly coun- try on hot days.

(cid:121) When towing a trailer, steering, stability, stopping distance and braking performance will be dif- ferent from normal operation. For safety’s sake, you should employ extra caution when towing a trail- er and you should never speed. You should also keep the follow- ing tips in mind:

– CONTINUED –

A3120BE-B.book 24 ページ ２００６年５月３０日　火曜日　午前９時３２分

8-24 Driving tips

(cid:84) Before starting out on a trip (cid:121) Check that the vehicle and vehicle-to- hitch mounting are in good condition. If any problems are apparent, do not tow the trailer. (cid:121) Check that the vehicle sits horizontally with the trailer attached. If the vehicle is tipped sharply up at the front and down at the rear, check the total trailer weight, GVW, GAWs and tongue load again, then confirm that the load and its distribution are acceptable. (cid:121) Check that the tire pressures are cor- rect. (cid:121) Check that the vehicle and trailer are connected properly. Confirm that

– the trailer tongue is connected prop- erly to the hitch ball. – the trailer lights connector is connect- ed properly and trailer’s brake lights illu- minate when the vehicle’s brake pedal is pressed, and that the trailer’s turn sig- nal lights flash when the vehicle’s turn signal lever is operated. – the safety chains are connected prop- erly. – all cargo in the trailer is secured safe- ty in position. – the side mirrors provide a good rear- ward field of view without a significant blind spot.

(cid:121) Sufficient time should be taken to learn

the “feel” of the vehicle/trailer combination before starting out on a trip. In an area free of traffic, practice turning, stopping and backing up.

(cid:84) Driving with a trailer (cid:121) You should allow for considerably more stopping distance when towing a trailer. Avoid sudden braking because it may re- sult in skidding or jackknifing and loss of control. (cid:121) Avoid uneven steering, sharp turns and rapid lane changes. (cid:121) Slow down before turning. Make a long- er than normal turning radius because the trailer wheels will be closer than the vehi- cle wheels to the inside of the turn. In a tight turn, the trailer could hit your vehicle. (cid:121) Crosswinds will adversely affect the handling of your vehicle and trailer, caus- ing sway. Crosswinds can be due to weather conditions or the passing of large trucks or buses. If swaying occurs, firmly grip the steering wheel and slow down im- mediately but gradually. (cid:121) When passing other vehicles, consider- able distance is required because of the added weight and length caused by at- taching the trailer to your vehicle.

800217

1) Left turn 2) Right turn

(cid:121) Backing up with a trailer is difficult and takes practice. When backing up with a trailer, never accelerate or steer rapidly. When turning back, grip the bottom of the steering wheel with one hand and turn it to the left for a left turn, and turn it to the right for a right turn. (cid:121) If the ABS warning light illuminates while the vehicle is in motion, stop towing the trailer and have repairs performed im- mediately by the nearest SUBARU dealer.

(cid:84) Driving on grades (cid:121) Before going down a steep hill, slow down and shift into lower gear (if neces- sary, use 1st gear) in order to utilize the engine braking effect and prevent over-

A3120BE-B.book 25 ページ ２００６年５月３０日　火曜日　午前９時３２分

Driving tips 8-25

cle and trailer when parking. Apply the parking brake firmly. You should not park on a hill or slope. But if parking on a hill or slope cannot be avoided, you should take the following steps: 1. Apply the brakes and hold the pedal down. 2. Have someone place wheel blocks un- der both the vehicle and trailer wheels. 3. When the wheel blocks are in place, re- lease the regular brakes slowly until the blocks absorb the load. 4. Apply the regular brakes and then ap- ply the parking brake; slowly release the regular brakes. 5. Shift into “P” and shut off the engine.

heating of your vehicle’s brakes. Do not make sudden downshifts. (cid:121) When driving uphill in hot weather, the air conditioner may turn off automatically to protect the engine from overheating. (cid:121) When driving uphill in hot weather, pay attention to the water temperature gauge pointer and AT OIL TEMP warning light since the engine and transmission are rel- atively prone to overheating under these conditions. If the water temperature gauge pointer approaches the OVERHEAT zone or the AT OIL TEMP warning light illumi- nates, immediately switch off the air con- ditioner and stop the vehicle at the nearest safe place. Refer to the “Engine overheat- ing” section in chapter 9, and “Warning and indicator lights” section in chapter 3. NOTE The temperature of engine coolant is less likely to rise to the OVERHEAT zone in the “D” position than in the manual mode position.

(cid:121) Avoid using the accelerator pedal to stay stationary on an uphill slope instead of using the parking brake or foot brake. That may cause the transmission fluid to overheat.

(cid:84) Parking on a grade Always block the wheels under both vehi-

A3120BE-B.book 26 ページ ２００６年５月３０日　火曜日　午前９時３２分

A3120BE-B.book 1 ページ ２００６年５月３０日　火曜日　午前９時３２分

In case of emergency

If you park your vehicle in an emergency ........ Spare tire ............................................................. Removing the spare tire ......................................... Re-storage of spare tire ......................................... Temporary spare tire .......................................... Flat tires .............................................................. Changing a flat tire ................................................. Tire pressure monitoring system (TPMS) ............

9-2
9-2
9-3
9-5
9-6
9-7
9-7
9-11
Jump starting ...................................................... 9-12
9-12
Engine overheating ............................................ 9-15

How to jump start ...................................................

If steam is coming from the engine

compartment .........................................................

9-15

If no steam is coming from the engine

compartment .........................................................

9-15
Towing ................................................................. 9-16
9-16
9-18
9-19

Towing and tie-down hooks .................................. Using a flat-bed truck ............................................. Towing with all wheels on the ground ..................

Rear gate – if the rear gate cannot be

unlocked .......................................................... 9-19
Maintenance tools .............................................. 9-20
9-20

Jack and jack handle ..............................................

A3120BE-B.book 2 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-2 In case of emergency

If you park your vehicle in an emergency

In case of emergency

the turn signals do not work.

Spare tire

300504

The hazard warning flasher should be used in day or night to warn other drivers when you have to park your vehicle under emergency conditions. Avoid stopping on the road. It is best to safely pull off the road if a problem occurs.

The hazard warning flasher can be acti- vated regardless of the ignition switch po- sition. Turn on the hazard warning by pushing the hazard warning flasher switch. Turn it off by pushing the switch again. NOTE When the hazard warning flasher is on,

900201

The spare tire is stored in the spare tire holder located under the cargo area. The spare tire holder has a hoist mecha- nism that can lower and raise the spare tire easily. The spare tire holder is designed to carry only the following kinds of tires: (cid:121) the temporary spare tire that came with your vehicle (cid:121) a full-size flat tire A full size flat tire should be stowed in the spare tire holder in an emergency only. Af- ter having the full-size flat tire repaired, immediately swap it with the temporary spare tire.

Before using the temporary spare tire, see

A3120BE-B.book 3 ページ ２００６年５月３０日　火曜日　午前９時３２分

the “Temporary spare tire” section in this chapter for instructions and precautions.

(cid:132) Removing the spare tire 1. Take the wheel nut wrench and exten- sion out of the tool bag. Refer to the “Main- tenance tools” section in this chapter.

In case of emergency 9-3

900202

2. Remove the subfloor storage lid in the cargo area. 3. Take out the jack.

900204

900206

4. Remove the cap. 5. Locate the hex-headed hoist shaft end inside the hole.

6. Fit the extension onto the hex-headed hoist shaft end.

900205

7. Fit the wheel nut wrench onto the ex- tension. 8. Turn the hoist shaft end counterclock- wise with the wheel nut wrench until the temporary spare tire is on the ground with enough cable slack to allow you to pull it out from under the vehicle.

(cid:121) Be sure to remove (not simply keep it open) the subfloor storage lid before turning the wheel nut wrench, otherwise the lid may be damaged.

– CONTINUED –

A3120BE-B.book 4 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-4 In case of emergency

(cid:121) Do not put your fingers into the center hole of the temporary spare tire while you pulling it out, because they might be pinched in between the wheel and the retain- er.

900208

(cid:121) Do not use the extension when turning the wheel nuts. If you did, you would not be able to achieve sufficient tightening torque. The wheel nuts could then come loose, resulting in a serious acci- dent.

900207

9. Tilt the retainer at the end of the cable and pull it through the center of the tempo- rary spare tire. 10.After the temporary spare tire is re- moved from the cable, the cable must be wound up completely by turning the hoist nut shaft clockwise until you hear a click- ing sound. Also visually inspect the cable to make certain that there is no longer any slack present.

(cid:121) When using the spare tire hoist:

After the temporary spare tire is removed from the cable, wind the cable up completely until the re- tainer at end of the cable sits against the underside of the vehi- cle. Driving with the cable not re- tracted fully could result in dam- age to the adjacent under floor parts and lead to a serious acci- dent.

(cid:121) The spare tire holder is designed to carry only the following kinds of tires: (cid:121) the temporary spare tire that

came with your vehicle

(cid:121) a full-size flat tire A full size flat tire should be stowed in the spare tire holder in an emergency only. After having the full-size flat tire repaired, im- mediately swap it with the tempo- rary spare tire. Never stow a full-size tire that is not flat in the spare tire holder. Doing so can result in damage to adjacent under floor parts and can lead to a serious accident.

A3120BE-B.book 5 ページ ２００６年５月３０日　火曜日　午前９時３２分

When using the spare tire hoist: Do not use air tools or power tools to turn the spare tire hoist shaft end. If you do, it could result in severe mechanical damage to the spare tire hoist.

(cid:132) Re-storage of spare tire 1. Turn the spare tire hoist shaft end counterclockwise with the wheel nut wrench to loosen the cable sufficiently enough to allow the cable end retainer go through center hole of the temporary spare tire. 2. Insert the retainer through the center hole of the temporary tire (with the outside of the tire facing up). 3. Turn the hoist shaft end clockwise with the wheel nut wrench to wind the cable up completely until you hear a few clicking sounds. Confirm that the temporary spare tire holding cable has been wound up completely by shaking the temporary tire.

If the temporary spare tire is not stored securely, it could damage ad- jacent areas of the vehicle and make an abnormal noise.

4. Put the rubber cap on the hoist shaft end hole. 5. Place the wheel nut wrench and exten- sion back into the tool bag and store the jack and tool bag in their storage loca- tions. 6. Fit the lid of the cargo area.

(cid:121) When stowing a flat tire in the spare tire holder, turn the hoist shaft end only slowly. If it is turned quickly, the wheel disc of the flat tire could be damaged.

(cid:121) A full-size flat tire should be stowed in the spare tire holder in an emergency only. After having the flat tire repaired, immediately swap it with the temporary spare tire.

In case of emergency 9-5

(cid:121) Remember that the tread width of a flat tire is wider than that of the temporary spare tire. When carry- ing a flat tire stowed in the spare tire holder, make sure the tire does not touch any obstacles.

A3120BE-B.book 6 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-6 In case of emergency

Temporary spare tire

(cid:121) Never tow a trailer when the tem- porary spare tire is used. The tem- porary spare tire is not designed to sustain the towing load. Use of the temporary spare tire when towing can result in failure of the spare tire and/or less stability of the vehicle and may lead to an ac- cident.

(cid:121) When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/trans- mitter being transferred, the low tire pressure warning light will flash. This indicates the tire pres- sure monitoring system (TPMS) is unable to monitor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replacement and/or system resetting.

900209

1) Tread wear indicator bar 2) Indicator location mark

(cid:121) When the wear indicator appears on the tread, replace the tire. (cid:121) The temporary spare tire must be used only on a rear wheel. If a front wheel tire gets punctured, replace the wheel with a rear wheel and install the temporary spare tire in place of the removed rear wheel.

Never use any temporary spare tire other than the original. Using other sizes may result in severe mechani- cal damage to the drive train of your vehicle.

The temporary spare tire is smaller and lighter than a conventional tire and is de- signed for emergency use only. Remove the temporary spare tire and re-install the conventional tire as soon as possible be- cause the spare tire is designed only for temporary use.

Check the inflation pressure of the tempo- rary spare tire periodically to keep the tire ready for use. The correct pressure is 60
psi (420 kPa, 4.2 kgf/cm2). When using the temporary spare tire, note the following. (cid:121) Do not exceed 50 mph (80 km/h). (cid:121) Do not put a tire chain on the temporary spare tire. Because of the smaller tire size, a tire chain will not fit properly. (cid:121) Do not use two or more temporary spare tires at the same time. (cid:121) Do not drive over obstacles. This tire has a smaller diameter, so road clearance is reduced.

A3120BE-B.book 7 ページ ２００６年５月３０日　火曜日　午前９時３２分

In case of emergency 9-7

(cid:121) Always turn off the engine before raising the flat tire off the ground using the jack. Never swing or push the vehicle supported with the jack. The jack can come out of the jacking point due to a jolt and this can result in a severe acci- dent.

1. Park on a hard, level surface, whenev- er possible, then stop the engine. 2. Set the parking brake securely and shift in the “P” (Park) position. 3. Turn on the hazard warning flasher and have everyone get out of the vehicle.

7 seater models 1) Jack handle 2) Jack 3) Spare tire

900261

Flat tires

If you have a flat tire while driving, never brake suddenly; keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place.

(cid:132) Changing a flat tire

(cid:121) Do not jack up the vehicle on an incline or a loose road surface. The jack can come out of the jack- ing point or sink into the ground and this can result in a severe ac- cident.

(cid:121) Use only the jack provided with your vehicle. The jack supplied with the vehicle is designed only for changing a tire. Never get un- der the vehicle while supporting the vehicle with this jack.

4. Put wheel blocks at the front and rear of the tire diagonally opposite the flat tire.

600122

– CONTINUED –

A3120BE-B.book 8 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-8 In case of emergency

nut wrench but do not remove the nuts.

900262

5 seater models 1) Jack handle 2) Jack 3) Spare tire

5. Take out the jack and jack handle. The jack and jack handle are stored under the floor of the cargo area. 6. Remove the spare tire. Refer to the sections “Spare tire” in this chapter for its location, instructions and precautions.

Carefully read the section “Temporary spare tire” in this chapter and strictly fol- low the instructions. NOTE Make sure the jack is well lubricated before using it.

900211

7. Insert the tip (wrapped in vinyl tape or a cloth) of a flat-head screwdriver into the slot between the wheel and cap. Use it to remove the cap.

900213

9. Place the jack under the side sill at the front or rear jack-up point closest to the flat tire.

8. Loosen the wheel nuts using the wheel

Turn the jackscrew by hand until the jack

900212

900214

A3120BE-B.book 9 ページ ２００６年５月３０日　火曜日　午前９時３２分

head engages firmly into the jack-up point.

900215

10.Insert the jack handle into the jack- screw, and turn the handle until the tire clears the ground. Do not raise the vehicle higher than necessary. 11.Remove the wheel nuts and the flat tire.

900009

600162

12.Before putting the spare tire on, clean the mounting surface of the wheel and hub with a cloth. 13.Put on the spare tire. Replace the wheel nuts. Tighten them by hand.

In case of emergency 9-9

Do not use oil or grease on the wheel studs or nuts when the spare tire is installed. This could cause the nuts to become loose and lead to an accident.

14.Turn the jack handle counterclockwise to lower the vehicle.

There are 2 types of wheel nut wrenches that apply to different lengths. For an aluminum wheel vehicle, the 11.2-inch (285 mm) wheel nut wrench is equipped as a mainte- nance tool. And for a chrome plated wheel vehicle, the 13.2-inch (335
mm) wheel nut wrench is equipped as well. Confirm the equipped wheel nut wrench type when you replace a tire. If the wheel nut wrench is the different type, it cannot be tightened to the specified torque.

– CONTINUED –

A3120BE-B.book 10 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-10 In case of emergency

(cid:31)

900292
900208

600192

1) The length of the wheel nut wrench

15.Confirm the length of the equipped wheel nut wrench. For an aluminum wheel vehicle, the 11.2- inch (285 mm) wheel nut wrench is equipped as a maintenance tool. And for a chrome plated wheel vehicle, the 13.2- inch (335 mm) wheel nut wrench is equipped as well.

16.Use the wheel nut wrench to securely tighten the wheel nuts to the specified torque, following the tightening order in the illustration. Wheel nuts tightening torque for tem- porary spare tire: 74 to 89 lbf·ft (100 to 120 N·m, 10 to 12
kgf·m) This torque is equivalent to applying the following load on the edge of the wheel nut wrench. When you use a wheel nut wrench of the 11.2-inch (285 mm) length: Approximately 88 to 110 lbs (40 to 50
kg)

When you use a wheel nut wrench of the 13.2-inch (335 mm) length: Approximately 73 to 87 lbs (33 to 38 kg)

Never use your foot on the wheel nut wrench or a pipe extension on the wrench because you may exceed the specified torque. Have torque checked at the nearest automotive service facility.

the wheel nut

900208

Do not use the extension when turn- ing the wheel nuts. If you did, you would not be able to achieve suffi- cient tightening torque. The wheel nuts could then come loose, result- ing in a serious accident.

A3120BE-B.book 11 ページ ２００６年５月３０日　火曜日　午前９時３２分

17.Store the flat tire in the spare tire hold- er. Refer to the sections “Spare tire” in this chapter for its location, instructions and precautions.

(cid:121) When stowing a flat tire in the spare tire holder, turn the hoist shaft end only slowly. If it is turned quickly, the wheel disc of the flat tire could be damaged.

(cid:121) A full-size flat tire should be stowed in the spare tire holder in an emergency only. After having the flat tire repaired, immediately swap it with the temporary spare tire.

(cid:121) Remember that the tread width of a flat tire is wider than that of the temporary spare tire. When carry- ing a flat tire stowed in the spare tire holder, make sure the tire does not touch any obstacles.

Never place a tire or tire changing tools in the passenger compartment after changing wheels. In a sudden stop or collisions, loose equipment could strike occupants and cause injury. Store the tire and all tools in the proper place.

(cid:132) Tire pressure monitoring sys-

tem (TPMS)

700318

The tire pressure monitoring system pro- vides the driver with the warning message indicated by sending a signal from a sen- sor that is installed in each wheel when tire pressure is severely low. The tire pressure monitoring system will

In case of emergency 9-11

activate only when the vehicle is driven. Also, this system may not react immedi- ately to a sudden drop in tire pressure (for example, a blow-out caused running over a sharp object).

If the low tire pressure warning light comes on while driving, never brake suddenly and keep driving straight ahead while gradually reducing speed. Then slowly pull off the road to a safe place. Otherwise an acci- dent involving serious vehicle dam- age and serious personal injury could occur. Check the pressure for all four tires and adjust the pressure to the COLD tire pressure shown on the vehicle placard on the door pillar on the driver’s side. If this light still comes on while driving after adjusting the tire pressure, a tire may have signif- icant damage and a fast leak that causes the tire to lose air rapidly. If you have a flat tire, replace it with a spare tire as soon as possible.

– CONTINUED –

A3120BE-B.book 12 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-12 In case of emergency

When a spare tire is mounted or a wheel rim is replaced without the original pressure sensor/transmitter being transferred, the low tire pres- sure warning light will flash. This in- dicates the TPMS is unable to moni- tor all four road wheels. Contact your SUBARU dealer as soon as possible for tire and sensor replace- ment and/or system resetting. Do not inject any tire liquid or aero- sol tire sealant into the tires, as this may cause a malfunction of the tire pressure sensors. If the light flashes, promptly contact a SUBARU dealer to have the sys- tem inspected.

Jump starting

(cid:121) Battery fluid is SULFURIC ACID. Do not let it come in contact with the eyes, skin, clothing or the ve- hicle. If battery fluid gets on you, thor- oughly flush the exposed area with water immediately. Get medi- cal help if the fluid has entered your eyes. is accidentally If battery fluid swallowed, immediately drink a large amount of milk or water, and obtain immediate medical help. Keep everyone including children away from the battery.

(cid:121) The gas generated by a battery ex- plodes if a flame or spark is brought near it. Do not smoke or light a match while jump starting. (cid:121) Never attempt jump starting if the discharged battery is frozen. It could cause the battery to burst or explode.

(cid:121) Whenever working on or around a battery, always wear suitable eye protectors, and remove metal ob- jects such as rings, bands or oth- er metal jewelry.

(cid:121) Be sure the jumper cables and clamps on them do not have loose or missing insulation. Do not jump start unless cables in suitable condition are available.

(cid:121) A running engine can be danger- ous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any oth- er moving engine parts. Remov- ing rings, watches and ties is ad- visable.

(cid:121) Jump starting is dangerous if it is done incorrectly. If you are unsure about the proper procedure for jump starting, consult a compe- tent mechanic.

When your vehicle does not start due to a run down (discharged) battery, the vehicle may be jump started by connecting your battery to another battery (called the booster battery) with jumper cables.

(cid:132) How to jump start 1. Make sure the booster battery is 12

A3120BE-B.book 13 ページ ２００６年５月３０日　火曜日　午前９時３２分

volts and the negative terminal is ground- ed. 2. If the booster battery is in another vehi- cle, do not let the two vehicles touch. 3. Turn off all unnecessary lights and ac- cessories. 4. Connect the jumper cables exactly in the sequence illustrated.

In case of emergency 9-13

– CONTINUED –

A3120BE-B.book 14 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-14 In case of emergency

(4)

(1)

(3)

(2)

1)Connect one jumper cable to the pos- itive (+) terminal on the discharged bat- tery. 2)Connect the other end of the jumper cable to the positive (+) terminal of the booster battery. 3)Connect one end of the other cable to the negative (–) terminal of the booster battery. 4)Connect the other end of the cable to the strut mounting nut.

Make sure that the cables are not near any moving parts and that the cable clamps are not in contact with any other metal.

900216

A3120BE-B.book 15 ページ ２００６年５月３０日　火曜日　午前９時３２分

5. Start the engine of the vehicle with the booster battery and run it at moderate speed. Then start the engine of the vehi- cle that has the discharged battery. 6. When finished, carefully disconnect the cables in exactly the reverse order.

In case of emergency 9-15

the engine and contact your authorized dealer for repair. 3. After the engine coolant temperature has dropped, turn off the engine. If the temperature gauge stays at the overheated zone, turn off the engine. 4. After the engine has fully cooled down, check the coolant level in the reserve tank. If the coolant level is below the “LOW” mark, add coolant up to the “FULL” mark. 5. If there is no coolant in the reserve tank, add coolant to the reserve tank. Then remove the radiator cap and fill the radiator with coolant.

If you remove the radiator cap from a hot radiator, first wrap a thick cloth around the radiator cap, then turn the cap counter- clockwise slowly without pressing down until it stops. Release the pressure from the radiator. After the pressure has been fully released, remove the cap by pressing down and turning it.

Engine overheating

Never attempt to remove the radia- tor cap until the engine has been shut off and has fully cooled down. When the engine is hot, the coolant is under pressure. Removing the cap while the engine is still hot could release a spray of boiling hot coolant, which could burn you very seriously.

If the engine overheats, safely pull off the road and stop the vehicle in a safe place.

(cid:132) If steam is coming from the

engine compartment

Turn off the engine and get everyone away from the vehicle until it cools down.

(cid:132) If no steam is coming from

the engine compartment

1. Keep the engine running at idling speed. 2. Open the hood to ventilate the engine compartment. Confirm that the cooling fan is turning. If the fan is not turning, immediately turn off

A3120BE-B.book 16 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-16 In case of emergency

Towing

Never tow AWD vehicles with the front wheels raised off the ground while the rear wheels are on the ground, or with the rear wheels raised off the ground while the front wheels are on the ground. This will cause the vehicle to spin away due to the operation or deterioration of the center differential.

900217

If towing is necessary, it is best done by your SUBARU dealer or a commercial towing service. Observe the following pro- cedures for safety.

(cid:132) Towing and tie-down hooks The towing hooks should be used only in an emergency (e.g., to free a stuck vehicle from mud, sand or snow).

(cid:121) Use only the specified towing hooks and tie-down hooks. Never use suspension parts or other parts of the body for towing or tie- down purposes.

(cid:121) Never use the tie-down hook clos- est to the muffler under the vehi- cle for towing purposes.

(cid:121) To prevent deformation to the bumper and the towing hook, do not apply excessive lateral load to the towing hooks.

Front towing hook: 1. Take out the towing hook, screwdriver and wheel nut wrench from the tool bag.

900218

2. Wrap a flat-head screwdriver in vinyl tape or cloth, insert it into the gap between the cover and the front bumper, and use it to pry the cover open. NOTE The cover is attached to the front bumper with five lugs.

A3120BE-B.book 17 ページ ２００６年５月３０日　火曜日　午前９時３２分

In case of emergency 9-17

After towing, remove the towing hook from the vehicle and stow it in the tool bag. Fit the towing hook cover on the bumper.

2. Pry off the cover on the rear bumper using a screwdriver, and you will find a threaded hole for attaching the towing hook.

900219

3. Screw the towing hook into the thread hole until the threads can no longer be seen.

(cid:121) Do not use the towing hook ex-

cept when towing your vehicle.

(cid:121) Be sure to remove the towing hook after towing. Leaving the towing hook mounted on the vehi- cle could interfere with proper op- eration of the SRS airbag system in a frontal collision.

Rear towing hook: 1. Take out the towing hook, screwdriver and wheel nut wrench from the on board tool bag.

3. Screw the towing hook into the thread hole until its thread can no longer be seen.

900222

4. Tighten the towing hook securely using a wheel nut wrench.

900220

900221

900223

– CONTINUED –

A3120BE-B.book 18 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-18 In case of emergency

4. Tighten the towing hook securely using a wheel nut wrench.

After towing, remove the towing hook from the vehicle and stow it in the tool bag. Put the thread hole cover on the rear bumper.

(cid:121) Do not use the towing hook ex-

cept when towing your vehicle.

(cid:121) Be sure to remove the towing hook after towing. Leaving the towing hook mounted on the vehi- cle could interfere with proper op- eration of the SRS airbag system in a frontal collision.

Front tie-down hooks:

900224

The front tie-down hooks are located be- tween each of the front tires and the front bumper.

Rear tie-down hooks:

(cid:132) Using a flat-bed truck

900226

This is the best way to transport your vehi- cle. Use the following procedures to en- sure safe transportation. 1. Shift the selector lever into the “P” po- sition. 2. Press the parking brake pedal firmly. 3. Secure the vehicle onto the carrier properly with safety chains. Each safety chain should be equally tightened and care must be taken not to pull the chains so tightly that the suspension bottoms out.

The rear tie-down hooks are located near each of the jack-up reinforcements.

900225

Use the rear tie-down hooks only for downward anchoring. If they are used to anchor the vehicle in any other direction, cables may slip off the hooks, possibly causing a dan- gerous situation.

A3120BE-B.book 19 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:132) Towing with all wheels on the

ground

900227

(cid:121) Never turn the ignition switch to the “LOCK” position while the ve- hicle is being towed because the steering wheel and the direction of the wheels will be locked.

(cid:121) Remember that the brake booster and power steering do not func- tion when the engine is not run- ning. Because is turned off, it will take greater ef- fort to operate the brake pedal and steering wheel.

the engine

(cid:121) If transmission failure occurs, transport your vehicle on a flat- bed truck.

(cid:121) Do not run the engine while being towed using this method. Trans- mission damage could result if the vehicle is towed with the en- gine running.

(cid:121) The traveling speed must be limit- ed to less than 20 mph (30 km/h) and the traveling distance to less than 31 miles (50 km). For greater speeds and distances, transport your vehicle on a flat-bed truck.

1. Check the transmission and differential oil levels and add oil to bring it to the upper level if necessary. 2. Release the parking brake and put the transmission in neutral. 3. The ignition switch should be in the “ACC” position while the vehicle is being towed. 4. Take up slack in the towline slowly to prevent damage to the vehicle.

In case of emergency 9-19

Rear gate – if the rear gate cannot be unlocked

In the event that you cannot unlock the rear gate by operating the power door locking switches or the remote keyless en- try system, you can unlock it from inside the cargo area.

900228

1. Remove the access cover at the bot- tom-center of the rear gate trim using flat- head screwdriver. 2. Locate the rear gate lock release lever behind the rear gate trim panel.

– CONTINUED –

A3120BE-B.book 20 ページ ２００６年５月３０日　火曜日　午前９時３２分

9-20 In case of emergency

Maintenance tools

(cid:132) Jack and jack handle

900263

3. Unlock the rear gate by moving the le- ver to the right. 4. Open the rear gate from outside by raising the rear gate handle.

Your vehicle is equipped with the following maintenance tools:

900230

7 seater models

900264

Screwdriver Towing hook (eye bolt) Wheel nut wrench Extension

900240

5 seater models

The jack and jack handle is stored under

A3120BE-B.book 21 ページ ２００６年５月３０日　火曜日　午前９時３２分

the cargo area.

For how to use the jack, refer to the “Flat tires” section in this chapter.

In case of emergency 9-21

A3120BE-B.book 22 ページ ２００６年５月３０日　火曜日　午前９時３２分

A3120BE-B.book 1 ページ ２００６年５月３０日　火曜日　午前９時３２分

Appearance care

Most common causes of corrosion ...................... To help prevent corrosion .....................................

Washing ................................................................... Waxing and polishing ............................................. Cleaning aluminum wheels ....................................

Exterior care ....................................................... 10-2
10-2
10-3
10-3
Corrosion protection .......................................... 10-3
10-3
10-4
Cleaning the interior .......................................... 10-4
10-4
10-4
10-5

Seat fabric ............................................................... Leather seat materials ............................................ Synthetic leather upholstery ................................. Climate control panel, audio panel, instrument panel, console panel, switches, combination meter, and other plastic surfaces .......................

10-5

10

A3120BE-B.book 2 ページ ２００６年５月３０日　火曜日　午前９時３２分

10-2 Appearance care

Exterior care

(cid:132) Washing

Appearance care

(cid:121) When washing the vehicle, the brakes may get wet. As a result, the brake stopping distance will be longer. To dry the brakes, drive the vehicle at a safe speed while lightly pressing the brake pedal to heat up the brakes.

(cid:121) Do not wash the engine compart- ment and areas adjacent to it. If water enters the engine air intake, electrical parts or the power steer- ing fluid reservoir, it will cause en- gine trouble or faulty power steer- ing respectively.

(cid:121) Since your vehicle is equipped with a rear wiper, automatic car- wash brushes could become tan- gled around it, damaging the wip- er arm and other components. Ask the automatic car-wash oper- ator not to let the brushes touch the wiper arm or to fix the wiper arm on the rear window glass with adhesive tape before operating the machine.

NOTE When having your vehicle washed in an automatic car wash, make sure be- forehand that the car wash is of suit- able type.

The best way to preserve your vehicle’s beauty is frequent washing. Wash the ve- hicle at least once a month to avoid con- tamination by road grime.

Wash dirt off with a wet sponge and plenty of lukewarm or cold water. Do not wash the vehicle with hot water and in direct sunlight.

Salt, chemicals, insects, tar, soot, tree sap, and bird droppings should be washed off by using a light detergent, as required. If you use a light detergent, make certain that it is a neutral detergent. Do not use strong soap or chemical detergents. All cleaning agents should be promptly flushed from the surface and not allowed to dry there. Rinse the vehicle thoroughly with plenty of lukewarm water. Wipe the remaining water off with a chamois or soft cloth. (cid:84) Washing the underbody Chemicals, salts and gravel used for deic- ing road surfaces are extremely corrosive, accelerating the corrosion of underbody

components, such as the exhaust system, fuel and brake lines, brake cables, floor pan and fenders, and suspension. Thoroughly flush the underbody and in- side of the fenders with lukewarm or cold water at frequent intervals to reduce the harmful effects of such agents.

Mud and sand adhering to the underbody components may accelerate their corro- sion. After driving off-road or muddy or sandy roads, wash the mud and sand off the un- derbody. Carefully flush the suspension and axle parts, as they are particularly prone to mud and sand buildup. Do not use a sharp-edged tool to remove caked mud. NOTE Be careful not to damage brake hoses, sensor harnesses, and other parts when washing suspension compo- nents.

(cid:84) Using a warm water washer (cid:121) Keep a good distance of 12 in (30 cm) or more between the washer nozzle and the vehicle. (cid:121) Do not wash the same area continuous- ly. (cid:121) If a stain will not come out easily, wash by hand. Some warm water washers are

A3120BE-B.book 3 ページ ２００６年５月３０日　火曜日　午前９時３２分

of the high temperature, high pressure type, and they can damage or deform the resin parts such as mouldings, or cause water to leak into the vehicle.

(cid:132) Waxing and polishing Always wash and dry the vehicle before waxing and polishing. Use a good quality polish and wax and ap- ply them according to the manufacturer’s instructions. Wax or polish when the paint- ed surface is cool.

Be sure to polish and wax the chrome trim, as well as the painted surfaces. Loss of wax on a painted surface leads to loss of the original luster and also quickens the deterioration of the surface. It is recom- mended that a coat of wax be applied at least once a month, or whenever the sur- face no longer repels water.

If the appearance of the paint has dimin- ished to the point where the luster or tone cannot be restored, lightly polish the sur- face with a fine-grained compound. Never polish just the affected area, but include the surrounding area as well. Always pol- ish in only one direction. A No. 2000 grain compound is recommended. Never use a coarse-grained compound. Coarser grained compounds have a smaller grain-

size number and could damage the paint. After polishing with a compound, coat with wax to restore the original luster. Frequent polishing with a compound or an incorrect polishing technique will result in removing the paint layer and exposing the under- coat. When in doubt, it is always best to contact your SUBARU dealer or an auto paint specialist. NOTE Be careful not to block the windshield washer nozzles with wax when waxing the vehicle.

(cid:132) Cleaning aluminum wheels (cid:121) Promptly wipe the aluminum wheels clean of any kind of grime or agent. If dirt is left on too long, it may be difficult to clean off. (cid:121) Do not use soap containing grit to clean the wheels. Be sure to use a neutral clean- ing agent, and later rinse thoroughly with water. Do not clean the wheels with a stiff brush or expose them to a high-speed washing device. (cid:121) Clean the vehicle (including the alumi- num wheels) with water as soon as possi- ble when it has been splashed with sea water, exposed to sea breezes, or driven on roads treated with salt or other agents.

Appearance care 10-3

Corrosion protection

Your SUBARU has been designed and built to resist corrosion. Special materials and protective finishes have been used on most parts of the vehicle to help maintain fine appearance, strength, and reliable operation.

(cid:132) Most common causes of cor-

rosion

The most common causes of corrosion are: 1. The accumulation of moisture retaining dirt and debris in body panel sections, cavities, and other areas. 2. Damage to paint and other protective coatings caused by gravel and stone chips or minor accidents.

Corrosion is accelerated on the vehicle when: 1. It is exposed to road salt or dust control chemicals, or used in coastal areas where there is more salt in the air, or in areas where there is considerable industrial pol- lution. 2. It is driven in areas of high humidity, es- pecially when temperatures range just above freezing. 3. Dampness in certain parts of the vehi- cle remains for a long time, even though – CONTINUED –

10

A3120BE-B.book 4 ページ ２００６年５月３０日　火曜日　午前９時３２分

10-4 Appearance care

other parts of the vehicle may be dry. 4. High temperatures will cause corrosion to parts of the vehicle which cannot dry quickly due to lack of proper ventilation.

(cid:132) To help prevent corrosion Wash the vehicle regularly to prevent cor- rosion of the body and suspension com- ponents. Also, wash the vehicle promptly after driving on any of the following surfac- es: (cid:121) roads that have been salted to prevent them from freezing in winter (cid:121) mud, sand, or gravel (cid:121) coastal roads

After the winter has ended, it is recom- mended that the underbody be given a very thorough washing.

Before the beginning of winter, check the condition of underbody components, such as the exhaust system, fuel and brake lines, brake cables, suspension, steering system, floor pan, and fenders. If any of them are found to be rusted, they should be given an appropriate rust prevention treatment or should be replaced. Contact your SUBARU dealer to perform this kind of maintenance and treatment if you need assistance.

Repair chips and scratches in the paint as

soon as you find them.

Cleaning the interior

Check the interior of the vehicle for water and dirt accumulation under the floor mats because that could cause corrosion. Oc- casionally check under the mats to make sure the area is dry.

Keep your garage dry. Do not park your vehicle in a damp, poorly ventilated ga- rage. In such a garage, corrosion can be caused by dampness. If you wash the ve- hicle in the garage or put the vehicle into the garage when wet or covered with snow, that can cause dampness.

If your vehicle is operated in cold weather and/or in areas where road salts and other corrosive materials are used, the door hinges and locks, trunk lid lock, and hood latch should be inspected and lubricated periodically.

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. (Do not use or- ganic solvents.)

(cid:132) Seat fabric Remove loose dirt, dust or debris with a vacuum cleaner. If the dirt is caked on the fabric or hard to remove with a vacuum cleaner, use a soft blush then vacuum it. Wipe the fabric surface with a tightly wrung cloth and dry the seat fabric thor- oughly. If the fabric is still dirty, wipe using a solution of mild soap and lukewarm wa- ter then dry thoroughly.

If the stain does not come out, try a com- mercially-available fabric cleaner. Use the cleaner on a hidden place and make sure it does not affect the fabric adversely. Use the cleaner according to its instructions. NOTE When cleaning the seat, do not use benzine, paint thinner, or any similar materials.

(cid:132) Leather seat materials The leather used by SUBARU is a high

A3120BE-B.book 5 ページ ２００６年５月３０日　火曜日　午前９時３２分

Appearance care 10-5

quality natural product which will retain its distinctive appearance and feel for many years with proper care. Allowing dust or road dirt to build up on the surface can cause the material to become brittle and to wear prematurely. Regular cleaning with a soft, moist, natural fiber cloth should be performed monthly, taking care not to soak the leather or allow water to penetrate the stitched seams. A mild detergent suitable for cleaning woolen fabrics may be used to remove dif- ficult dirt spots, rubbing with a soft, dry cloth afterwards to restore the luster. If your SUBARU is to be parked for a long time in bright sunlight, it is recommended that the seats and headrests be covered, or the windows shaded, to prevent fading or shrinkage. Minor surface blemishes or bald patches may be treated with a commercial leather spray lacquer. You will discover that each leather seat section will develop soft folds or wrinkles, which is characteristic of gen- uine leather.

(cid:132) Synthetic leather upholstery The synthetic leather material used on the SUBARU may be cleaned using mild soap or detergent and water, after first vacuum- ing or brushing away loose dirt. Allow the soap to soak in for a few minutes and wipe

off with a clean, damp cloth. Commercial foam-type cleaners suitable for synthetic leather materials may be used when nec- essary. NOTE Strong cleaning agents such as sol- vents, paint thinners, window cleaner or gasoline must never be used on leather or synthetic interior materials.

(cid:132) Climate control panel, audio panel, instrument panel, con- sole panel, switches, combi- nation meter, and other plas- tic surfaces

Use a soft, damp cloth to clean the climate control panel, audio equipment, instru- ment panel, center console, combination meter panel, and switches. NOTE Do not use organic solvents such as paint thinners or gasoline, or strong cleaning agents that contain those sol- vents.

10

A3120BE-B.book 6 ページ ２００６年５月３０日　火曜日　午前９時３２分

A3120BE-B.book 1 ページ ２００６年５月３０日　火曜日　午前９時３２分

Maintenance schedule ....................................... 11-3
Maintenance precautions .................................. 11-3

Before checking or servicing in the engine

compartment ........................................................

11-4

When you do checking or servicing in the engine compartment while the engine is running ..................................................................

11-4
Engine hood ....................................................... 11-4
Engine compartment overview ......................... 11-6
Engine oil ............................................................ 11-7
11-7
11-7
11-9

Checking the oil level ............................................. Changing the oil and oil filter ................................ Recommended grade and viscosity ..................... Recommended grade and viscosity under severe

driving conditions ................................................ 11-10
Cooling system .................................................. 11-10
Hose and connections ........................................... 11-11
Engine coolant ........................................................ 11-11
Air cleaner element ............................................ 11-13
Replacing the air cleaner element ......................... 11-13
Spark plugs ......................................................... 11-14
Recommended spark plugs ................................... 11-14
Drive belts ........................................................... 11-15
Automatic transmission fluid ............................ 11-15
Checking the fluid level ......................................... 11-15
Recommended fluid ............................................... 11-16
Front differential gear oil ................................... 11-16
Checking the oil level ............................................. 11-16

Maintenance and service

Recommended grade and viscosity ..................... 11-17
Rear differential gear oil .................................... 11-17
Checking the gear oil level .................................... 11-17
Recommended grade and viscosity ..................... 11-18
Power steering fluid ........................................... 11-19
Checking the fluid level .......................................... 11-19
Recommended fluid ............................................... 11-19
Brake fluid ........................................................... 11-20
Checking the fluid level .......................................... 11-20
Recommended brake fluid ..................................... 11-20
Brake booster ..................................................... 11-21
Brake pedal ......................................................... 11-21
Checking the brake pedal free play ...................... 11-21
Checking the brake pedal reserve distance ......... 11-21
Replacement of brake pad and lining ............... 11-22
Breaking-in of new brake pads and linings .......... 11-22
Parking brake stroke .......................................... 11-23
Tires and wheels ................................................ 11-23
Types of tires .......................................................... 11-23
Tire pressure monitoring system (TPMS) ............ 11-23
Tire inspection ........................................................ 11-25
Tire pressures and wear ........................................ 11-25
Wheel balance ......................................................... 11-27
Wear indicators ....................................................... 11-27
Tire rotation direction mark ................................... 11-28
Tire rotation ............................................................. 11-28
Tire replacement ..................................................... 11-29
Wheel replacement ................................................. 11-30

11

A3120BE-B.book 2 ページ ２００６年５月３０日　火曜日　午前９時３２分

Maintenance and service

Aluminum wheels ............................................... 11-30
Chrome plated wheels (if equipped) ................. 11-31
Windshield washer fluid .................................... 11-32
Replacement of wiper blades ............................ 11-33
Windshield wiper blade assembly ........................ 11-34
Windshield wiper blade rubber ............................. 11-34
Rear window wiper blade assembly ..................... 11-35
Rear window wiper blade rubber .......................... 11-36
Battery ................................................................. 11-37
Fuses ................................................................... 11-38
Main fuse ............................................................. 11-40
Installation of accessories ................................ 11-40
Replacing bulbs .................................................. 11-41
Headlight ................................................................. 11-42
Parking light ............................................................ 11-45
Front turn signal light ............................................ 11-45
Front fog light ......................................................... 11-45
Rear combination lights ......................................... 11-46
Backup light/Tail light ............................................ 11-46
Rear gate light ......................................................... 11-47
License plate light .................................................. 11-47
Dome light ............................................................... 11-48
Map light .................................................................. 11-48
Door step light ........................................................ 11-49
Cargo area light ...................................................... 11-49

A3120BE-B.book 3 ページ ２００６年５月３０日　火曜日　午前９時３２分

Maintenance schedule

Maintenance and service

Maintenance precautions

The scheduled maintenance items re- quired to be serviced at regular intervals are shown in the “Warranty and Mainte- nance Booklet”.

For details of your maintenance schedule, read the separate “Warranty and Mainte- nance Booklet”.

When maintenance and service are re- quired, it is recommended that all work be done by an authorized SUBARU dealer.

If you perform maintenance and service by yourself, you should familiarize your- self with the information provided in this section on general maintenance and ser- vice for your SUBARU.

Incorrect or incomplete service could cause improper or unsafe vehicle opera- tion. Any problems caused by improper maintenance and service performed by you are not eligible for warranty coverage.

(cid:121) Testing of an All-Wheel Drive ve- hicle must NEVER be performed on a single two-wheel dynamome- ter or similar apparatus. Attempt- ing to do so will result in transmis- sion damage and in uncontrolled vehicle movement and may cause an accident or injuries to persons nearby.

(cid:121) Always select a safe area when performing maintenance on your vehicle.

Maintenance and service 11-3

(cid:121) Always be very careful to avoid in- jury when working on the vehicle. Remember that some of the mate- rials in the vehicle may be hazard- ous if improperly used or handled, for example, battery acid.

(cid:121) Your vehicle should only be ser- viced by persons fully competent to do so. Serious personal injury may result to persons not experi- enced in servicing vehicles.

(cid:121) Always use the proper tools and make certain that they are well maintained.

(cid:121) Never get under the vehicle sup- ported only by a jack. Always use a safety stands to support the ve- hicle.

(cid:121) Never keep the engine running in a poorly ventilated area, such as a garage or other closed areas.

(cid:121) Do not smoke or allow open flames around the fuel or battery. This will cause a fire.

(cid:121) Because the fuel system is under pressure, replacement of the fuel filter should be performed only by your SUBARU dealer.

– CONTINUED –

11

A3120BE-B.book 4 ページ ２００６年５月３０日　火曜日　午前９時３２分

11-4 Maintenance and service

(cid:121) Wear adequate eye protection to guard against getting oil or fluids in your eyes. If something does get in your eyes, thoroughly wash them out with clean water.

(cid:121) Do not tamper with the wiring of the SRS airbag system or seatbelt pretensioner system, or attempt to take its connectors apart, as that may activate the system or it can render it inoperative. The wir- ing and connectors of these sys- tems are yellow for easy identifi- cation. NEVER use a circuit tester for these wiring. If your SRS airbag or seatbelt pre- tensioner needs service, consult your nearest SUBARU dealer.

(cid:132) Before checking or servicing

in the engine compartment

(cid:121) Always stop the engine and set the parking brake firmly to pre- vent the vehicle from moving.

(cid:121) Always let the engine cool down. Engine parts become very hot when the engine is running and remain hot for some time after the engine is stopped.

(cid:121) Do not spill engine oil, engine coolant, brake fluid or any other fluid on hot engine components. This may cause a fire.

(cid:121) Always remove the key from the ignition switch. When the ignition switch is in the “ON” position, the cooling fan may operate suddenly even when the engine is stopped.

(cid:132) When you do checking or ser- vicing in the engine compart- ment while the engine is run- ning

A running engine can be dangerous. Keep your fingers, hands, clothing, hair and tools away from the cooling fan, belts and any other moving en- gine parts. Removing rings, watch- es and ties is advisable.

Engine hood

B00300

To open the hood: 1. If the wiper blades are lifted off the windshield, return them to their original positions. 2. Pull the hood release knob under the instrument panel.

A3120BE-B.book 5 ページ ２００６年５月３０日　火曜日　午前９時３２分

Maintenance and service 11-5