2007 Subaru Tribeca Owners Manual

vehicle.

Do not touch the SRS side airbag system components around the front seat seatback with bare hands right after deployment. Doing so can cause burns because the compo- nents can be very hot as a result of deployment. After deployment, do not touch any part of the SRS curtain airbag sys- tem (from the front pillar to the part of the roof side over the rear seat). Doing so can cause burns because the components can be very hot as a result of deployment.

The SRS side airbag and SRS curtain air- bag are designed to deploy in the event of an accident involving a moderate to se- vere side impact collision. Also, in the case of a rollover, the SRS curtain airbag deploys. They are basically not designed to deploy in a lesser side impact. Also, they are basically not designed to deploy in frontal or rear impacts because SRS side airbag and SRS curtain airbag de- ployment would not help the occupant in those situations. Each SRS side airbag and SRS curtain airbag are designed to function on a one- time-only basis.

SRS side airbag and SRS curtain airbag deployment depend on the level of force experienced in the passenger compart- ment during a side impact collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle it- self. Also, the SRS curtain airbag deploys depending on the vehicle’s position and inclination at the time of the rollover.

(cid:86) Example of the type of accident in

which the SRS side airbag will most likely deploy.

A severe side impact near the front seat activates the SRS side airbag.

200320

A3120BE-B.book 65 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:86) Examples of the types of accidents in which the SRS curtain airbag will most

likely deploy.

Seat, seatbelt and SRS airbags 1-65

1) A severe side impact near the front

seat or the rear seat activates the SRS curtain airbag.

2) The vehicle rolls onto its side or the roof. If the angle of vehicle tip-up is marginal 3) or if the skidding vehicle’s tires hit a curbstone laterally.

100833

– CONTINUED –

A3120BE-B.book 66 ページ ２００６年５月３０日　火曜日　午前９時３２分

1-66 Seat, seatbelt and SRS airbags

(cid:86) Examples of the types of accidents in which it is possible that the SRS side air-

bag and the SRS curtain airbag will deploy.

1) Hitting a curb, edge of pavement or

hard surface

2) Falling into or jumping over a deep

hole

3) Landing hard or vehicle falling

It is possible that the SRS side and curtain airbags will deploy if a serious impact oc- curs to the underside of your vehicle. Some examples are shown in the illustra- tion.

100834

A3120BE-B.book 67 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:86) Examples of the types of accidents in which the SRS side airbag is unlikely to

deploy.

Seat, seatbelt and SRS airbags 1-67

1) The vehicle is involved in an oblique

side-on impact.

2) The vehicle is involved in a side-on

impact in an area outside the vicinity of the passenger compartment.

3) The vehicle strikes a telephone pole

or similar object.

4) The vehicle is involved in a side-on

impact from a motorcycle.

5) The vehicle rolls onto its side or the

roof.

There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of acci- dents like those illustrated, the SRS side airbag may not deploy depending on the level of accident forces involved.

100835

– CONTINUED –

A3120BE-B.book 68 ページ ２００６年５月３０日　火曜日　午前９時３２分

1-68 Seat, seatbelt and SRS airbags

(cid:86) Examples of the types of accidents in which the SRS curtain airbag is unlikely

to deploy.

1) The vehicle is involved in an oblique

side-on impact.

2) The vehicle is involved in a side-on

impact in an area outside the vicinity of the passenger compartment.

3) The vehicle is involved in a side-on

impact from a motorcycle.

There are many types of collisions which might not necessarily require SRS curtain airbag deployment. In the event of acci- dents like those illustrated, the SRS cur- tain airbag may not deploy depending on the level of accident forces involved.

100836

A3120BE-B.book 69 ページ ２００６年５月３０日　火曜日　午前９時３２分

ary).

2) The vehicle is struck from behind.

The SRS side airbag and SRS curtain air- bag are basically not designed to deploy if the vehicle is involved in a frontal collision or is struck from behind. Examples of such accidents are illustrated. (cid:86) Example of the type of accident in which the SRS curtain airbag will basically not deploy.

(cid:86) Examples of the types of accidents

in which the SRS side airbag and SRS curtain airbag will basically not deploy.

100832

The SRS curtain airbags are not basically designed to deploy if the vehicle pitches end over end.

1) The vehicle is involved in frontal collision with another vehicle (moving or station-

100541

Seat, seatbelt and SRS airbags 1-69

100563

1) First impact 2) Second impact A) SRS curtain airbag B) SRS side airbag

In an accident where the vehicle is struck from the side more than once, the SRS side airbag and SRS curtain airbag deploy only once on the first impact.

Example: In the case of a double side im- pact collision, first with one vehicle and immediately followed by another from the same direction, once the SRS side airbag and SRS curtain airbag are activated on the first impact, they will not be activated on the second.

– CONTINUED –

A3120BE-B.book 70 ページ ２００６年５月３０日　火曜日　午前９時３２分

1-70 Seat, seatbelt and SRS airbags

(cid:132) SRS airbag system monitors

100385

A diagnostic system continually monitors the readiness of the SRS airbag system (including front seatbelt pretensioners) while the vehicle is being driven. The SRS airbag system warning light “AIRBAG” will show normal system operation by lighting for approximately 6 seconds when the ig- nition switch is turned to the “ON” position.

The following components are monitored by the indicator: (cid:121) Front sub sensor (Right-hand side) (cid:121) Front sub sensor (Left-hand side) (cid:121) Airbag control module (including impact and rollover sensors) (cid:121) Frontal airbag module (Driver’s side) (cid:121) Frontal airbag module (Front passen- ger’s side)

(cid:121) Side airbag sensor (Center pillar right- hand side) (cid:121) Side airbag sensor (Center pillar left- hand side) (cid:121) Side airbag module (Driver’s side) (cid:121) Side airbag module (Front passenger’s side) (cid:121) Curtain airbag sensor (Rear wheel house right-hand side) (cid:121) Curtain airbag sensor (Rear wheel house left-hand side) (cid:121) Curtain airbag module (Right side) (cid:121) Curtain airbag module (Left side) (cid:121) Seatbelt pretensioner (Driver’s side) (cid:121) Seatbelt pretensioner (Front passen- ger’s side) (cid:121) Seatbelt buckle switch (Driver’s side) (cid:121) Seatbelt buckle switch (Front passen- ger’s side) (cid:121) Driver’s seat position sensor (cid:121) Front passenger’s seatbelt tension sen- sor (cid:121) Front passenger’s occupant detection system weight sensor (cid:121) Front passenger’s occupant detection control module (cid:121) Front passenger’s frontal airbag ON and OFF indicator (cid:121) All related wiring

If the warning light exhibits any of the following conditions, there may be a malfunction in the seatbelt pre- tensioners and/or SRS airbag sys- tem. Immediately take your vehicle to your nearest SUBARU dealer to have the system checked. Unless checked and properly repaired, the seatbelt pretensioners and/or SRS airbags will operate improperly (e.g. SRS airbags may inflate in a very mi- nor collision or not inflate in a se- vere collision), which may increase the risk of injury. (cid:121) Flashing or flickering of the warn-

ing light

(cid:121) No illumination of the warning light when the ignition switch is first turned to the “ON” position

(cid:121) Continuous illumination of the

warning light

(cid:121) Illumination of the warning light

while driving

1

A3120BE-B.book 71 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:132) SRS airbag system servicing

(cid:121) When discarding an airbag mod- ule or scrapping the entire vehicle damaged by a collision, consult your SUBARU dealer.

(cid:121) The SRS airbag has no user-ser- viceable parts. Do not use electri- cal test equipment on any circuit related to the SRS airbag system. For required servicing of the SRS airbag, see your nearest SUBARU dealer. Tampering with or discon- necting the system’s wiring could result in accidental inflation of the SRS airbag or could make the sys- tem inoperative, which may result in serious injury. The wiring har- nesses of the SRS airbag system are covered with yellow insulation and system connectors are yellow for easy identification.

If you need service or repair in areas listed in the following, have an au- thorized SUBARU dealer perform the work. The SRS airbag control module, impact sensors and airbag modules are stored in these areas. (cid:121) Under the center console (cid:121) Inside each front fender (cid:121) Steering wheel and column and

nearby areas

(cid:121) Top of the dashboard on front passenger’s side and nearby ar- eas

(cid:121) Each front seat and nearby area (cid:121) Inside each center pillar (cid:121) In each roof side (from the front pillar to a point over the rear seat) (cid:121) Between the rear seat cushion and rear wheel house on each side

In the event that the SRS airbag is de- ployed, replacement of the system should be performed only by an autho- rized SUBARU dealer. When the com- ponents of the SRS airbag system are replaced, use only genuine SUBARU

Seat, seatbelt and SRS airbags 1-71

parts. NOTE In the following cases, contact your SUBARU dealer as soon as possible. (cid:121) The front part of the vehicle was in- volved in an accident in which only the driver’s SRS frontal airbag or both driv- er’s and front passenger’s SRS frontal airbags did not deploy. (cid:121) The pad of the steering wheel, the cover over the front passenger’s SRS frontal airbag, or either roof side (from the front pillar to a point over the rear seat) is scratched, cracked, or other- wise damaged. (cid:121) Either center pillar and rear wheel house or a nearby area of the vehicle was involved in an accident in which the SRS side airbag and SRS curtain airbag did not deploy. (cid:121) The fabric or leather of either front seatback is cut, frayed, or otherwise damaged.

– CONTINUED –

A3120BE-B.book 72 ページ ２００６年５月３０日　火曜日　午前９時３２分

1-72 Seat, seatbelt and SRS airbags

(cid:132) Precautions against vehicle

modification

(cid:121) To avoid accidental activation of the system or rendering the sys- tem inoperative, which may result in serious injury, no modifications should be made to any compo- nents or wiring of the SRS airbag system. This includes following modifica- tions: (cid:121) Installation of custom steering

wheels

(cid:121) Attachment of a hands-free mi- crophone or any other accesso- ry to a front pillar, a center pillar, a rear pillar, the windshield, a side window, an assist grip, or any other cabin surface that would be near a deploying SRS curtain airbag.

(cid:121) Installation of additional electri- cal/electronic equipment such as a mobile two-way radio on or near the SRS airbag system components and/or wiring is not advisable. This could inter- fere with proper operation of the SRS airbag system.

(cid:121) Installation of a tire of different size and construction from the tires specified on the vehicle plac- ard attached to the driver’s door pillar or specified for individual vehicle models in this Owner’s Manual.

(cid:121) Attachment of any equipment (side steps or side sill protectors, etc.) other than genuine SUBARU accessory parts to the side body.

Always consult your SUBARU dealer if you want to install any accessory parts on your vehicle.

(cid:121) Attachment of additional trim

materials to the dashboard (cid:121) Installation of custom seats (cid:121) Replacement of seat fabric or

leather

(cid:121) Installation of additional fabric

or leather on the front seat

Do not perform any of the following modifications. Such modifications can interfere with proper operation of the SRS airbag system. (cid:121) Attachment of any equipment (bush bar, winches, snow plow, skid plate, etc.) other than genu- ine SUBARU accessory parts.

(cid:121) Modification of the suspension

system or front end structure.

A3120BE-B.book 1 ページ ２００６年５月３０日　火曜日　午前９時３２分

Keys and doors

Valet mode ............................................................... Passive arming ....................................................... Tripped sensor identification ................................ Shock sensors (dealer option) ..............................

2-17
2-17
2-18
2-18
Child safety locks ............................................... 2-19
Windows .............................................................. 2-19
2-19
Rear gate ............................................................. 2-22
Moonroof (if equipped) ...................................... 2-23
2-24
2-24
2-24
2-25

Tilt function ............................................................. Sliding function ....................................................... Anti-entrapment function ....................................... Sun shade ................................................................

Power windows .......................................................

Keys ..................................................................... Key number plate .................................................... Immobilizer ......................................................... Security ID plate ..................................................... Security indicator light ........................................... Key replacement ..................................................... Door locks ........................................................... Locking and unlocking from the outside ............. Locking and unlocking from the inside ................ Battery drainage prevention function ................... Power door locking switches ............................ Key lock-in prevention function ............................ Remote keyless entry system ........................... Locking the doors .................................................. Unlocking the doors ............................................... Unlocking the rear gate .......................................... Illuminated entry ..................................................... Vehicle finder function ........................................... Sounding a panic alarm ......................................... Selecting audible signal operation ....................... Replacing the battery ............................................. Replacing lost transmitters ...................................

2-2
2-2
2-3
2-3
2-4
2-4
2-4
2-4
2-5
2-6
2-6
2-7
2-8
2-9
2-9
2-9
2-9
2-10
2-10
2-10
2-10
2-11
Alarm system ...................................................... 2-14
2-14
2-15

System operation ................................................... Activating and deactivating the alarm system ..... If you have accidentally triggered the alarm

system ................................................................... Arming the system ................................................. Disarming the system ............................................

2-15
2-15
2-16

A3120BE-B.book 2 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-2 Keys and doors

Keys

Keys and doors

box locked when you leave your vehicle and valet key at a parking facility.

Do not attach a large key holder or key case to either key. If it bangs against your knees while you are driving, it could turn the ignition switch from the ON position to the ACC or OFF position, thereby stop- ping the engine.

Write down the key number and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehicle.

For information on making replacement keys for vehicles with the immobilizer sys- tem, refer to the “Immobilizer” section in this chapter.

(cid:132) Key number plate

200700

1) Master key 2) Submaster key 3) Valet key 4) Key number plate 5) Security ID plate

Three types of keys are provided for your vehicle. Master key, submaster key and valet key.

The master key and submaster key fit all locks on your vehicle. (cid:121) Ignition switch (cid:121) Driver’s door (cid:121) Glove box

The valet key fits only the ignition switch and door locks. You can keep the glove

200701

1) Key number plate 2) Security ID plate

The key number is stamped on the key number plate attached to the key set.

A3120BE-B.book 3 ページ ２００６年５月３０日　火曜日　午前９時３２分

Immobilizer

The immobilizer system is designed to prevent an unauthorized person from starting the engine. Only keys registered with your vehicle’s immobilizer system can be used to operate your vehicle. Even if an unregistered key fits into the ignition switch and can be turned to the “START” position, the engine will automatically stop after several seconds.

Each immobilizer key contains a tran- sponder in which the key’s ID code is stored. When a key is inserted into the ig- nition switch and turned to the “ON” posi- tion, the transponder transmits the key’s ID code to the immobilizer system’s re- ceiver. If the transmitted ID code matches the ID code registered in the immobilizer system, the system allows the engine to be started. Since the ID code is transmit- ted and acted upon almost instantly, the immobilizer system does not impede nor- mal starting of the engine. If the engine fails to start, pull out the key once before trying again. (Refer to the “Ig- nition switch” section [chapter 3].) This device complies with Part 15 of the FCC Rules and with RSS-210 of In- dustry Canada. Operation is subject to the following two conditions: (1) This

device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including in- terference that may cause undesired operation. Changes or modifications not express- ly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE To protect your vehicle from theft, please pay close attention to the fol- lowing security precautions: (cid:121) Never leave your vehicle unattended with its keys inside. (cid:121) Before leaving your vehicle, close all windows and lock the doors and rear gate. (cid:121) Do not leave spare keys or any record of your key number in the vehi- cle.

(cid:121) Do not place the key under direct sunlight or anywhere it may be- come hot.

(cid:121) Do not get the key wet. If the key gets wet, wipe it dry with a cloth immediately.

Keys and doors 2-3

(cid:132) Security ID plate

200701

1) Key number plate 2) Security ID plate

The security ID is stamped on the security ID plate attached to the key set. Write down the security ID and keep it in another safe place, not in the vehicle. This number is needed to make a replacement key if you lose your key or lock it inside the vehi- cle. This number is also needed for replace- ment or repair of the engine control unit, integrated unit, and combination meter.

– CONTINUED –

A3120BE-B.book 4 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-4 Keys and doors

(cid:132) Security indicator light

200702

The security indicator light deters potential thieves by indicating that the vehicle is equipped with an immobilizer system. It begins flashing approximately 60 seconds after the ignition switch is turned from the “ON” position to the “ACC” or “LOCK” po- sition or immediately after the key is pulled out. If the security indicator light does not flash, the immobilizer system may be faulty. this occurs, contact your SUBARU dealer as soon as possible.

If

In case an unauthorized key is used (e.g. an imitation key), the security indicator light comes on.

NOTE Even if the security indicator light flashes irregularly or its fuse blows (the light does not flash if its fuse is blown), the immobilizer system will function normally.

(cid:132) Key replacement Your key number plate and security ID plate will be required if you ever need a re- placement key made. Any new key must be registered for use with your vehicle’s immobilizer system before it can be used. Up to four keys can be registered for use with one vehicle. For security, all the keys registered with your vehicle’s immobilizer system will have their ID codes erased and re-regis- tered when a new key is made. Therefore, all of your vehicle’s keys must be present- ed when a new key is registered. Any key that is not re-registered when a new key is made cannot be used after the other keys are re-registered. For information on re- placement keys and on the registration of keys with your immobilizer system, con- tact your SUBARU dealer.

Door locks

(cid:132) Locking and unlocking from

the outside

200703

To lock the driver’s door from the outside with the key, turn the key toward the front. To unlock the door, turn the key toward the rear.

Lift the outside door handle to open an un- locked door.

A3120BE-B.book 5 ページ ２００６年５月３０日　火曜日　午前９時３２分

200704

Locking without the key

To lock the door from the outside without the key, rotate the lock lever rearward and then close the door.

Keys and doors 2-5

It also helps prevent passengers from falling out if a door is acciden- tally opened, and intruders from un- expectedly opening doors and en- tering your vehicle.

To lock the door from the inside, rotate the lock lever rearward.

200706

To lock the door from the outside using the power door locking switch, push the “ ” sides of the switch and then close the door. In this case, all closed doors and the rear gate are locked at the same time.

Always make sure that all doors and the rear gate are locked before leaving your vehicle. NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside without the key.

(cid:132) Locking and unlocking from

the inside

Keep all doors locked when you drive, especially when small chil- dren are in your vehicle. Along with the proper use of seat- belts and child restraints, locking the doors reduces the chance of be- ing thrown out of the vehicle in an accident.

Locking without the key

200705

– CONTINUED –

A3120BE-B.book 6 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-6 Keys and doors

by the battery drainage prevention func- tion after 10 minutes of illumination to pre- vent the battery from going dead. The op- erational/non-operational setting of this function can be changed by a SUBARU dealer. Contact the nearest SUBARU dealer if you would like to change the set- ting. NOTE (cid:121) When leaving the vehicle, please make sure that all doors and the rear gate are completely closed. (cid:121) The battery drainage prevention function does not operate while the key is in the ignition switch.

Power door locking switches

200708

Driver’s switch 1) Lock 2) Unlock

200707

To unlock the door from the inside, rotate the lock lever forward.

The red mark on the lock lever appears when the door is unlocked. Pull the inside door handle to open an un- locked door. Always make sure that all doors and the rear gate are closed and locked before starting to drive.

(cid:132) Battery drainage prevention

function

When a door or the rear gate is not com- pletely closed and the map light, dome light, ignition switch light, and door open warning light remain illuminated as a re- sult, the lights are automatically turned off

Keys and doors 2-7

setting can be changed by a SUBARU dealer. Contact a SUBARU dealer for de- tails. NOTE When leaving the vehicle, make sure you are holding the key before locking the doors.

A3120BE-B.book 7 ページ ２００６年５月３０日　火曜日　午前９時３２分

200709

Front passenger’s switch 1) Lock 2) Unlock

All doors and the rear gate can be locked and unlocked by the power door locking switches located at the driver’s side and the front passenger’s side doors.

To lock all doors (including the rear gate), push the “ To unlock all doors (including the rear ” side of the switch. gate), push the “

” side of the switch.

When you close the doors after you set the door locks, the doors remain locked. NOTE Make sure that you do not leave the key inside the vehicle before locking the doors from the outside using the pow-

er door locking switches.

(cid:132) Key lock-in prevention func-

tion

This function prevents the doors from be- ing locked with the key still in the ignition switch. (cid:84) Behavior with key lock-in preven-

tion function operative

With either the driver’s or front passen- ger’s door open, the doors automatically remain unlocked even if the “ ” side of the door locking switch is pushed. (cid:84) Behavior with key lock-in preven-

tion function non-operative

(cid:121) If the lock lever is turned to the rear (“LOCK”) position with the driver’s door open and the driver’s door is then closed with the lock lever in that position, the driv- er’s door is locked. (cid:121) If the spare key is used to lock the driv- er’s door from the outside of the vehicle, the door is locked. (cid:121) It is possible to lock the all doors and the rear gate by holding the “ ” side of the door locking switch pushed for three sec- onds with the driver’s door open and then closing the driver’s door.

This

function’s operative/non-operative

A3120BE-B.book 8 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-8 Keys and doors

Remote keyless entry sys- tem

(cid:121) Do not expose the transmitter to severe shocks, such as those ex- perienced as a result of dropping or throwing.

(cid:121) Do not take the transmitter apart except when replacing the bat- tery.

(cid:121) Do not get the transmitter wet. If it gets wet, wipe it dry with a cloth immediately.

This device complies with Part 15 of the FCC Rules and with RSS-210 of In- dustry Canada. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including in- terference that may cause undesired operation. Changes or modifications not express- ly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Two transmitters are provided for your ve-

hicle.

The keyless entry system has the follow- ing functions. (cid:121) Locking and unlocking the doors (and rear gate) without a key (cid:121) Unlocking the rear gate without key (cid:121) Sounding a panic alarm (cid:121) Arming and disarming the alarm sys- tem. See the next section “Alarm system” for detailed information.

The operable distance of the keyless entry system is approximately 30 feet (10
meters). However, this distance will vary depending on environmental conditions. The system’s operable distance will be shorter in areas near a facility or electronic equipment emitting strong radio waves such as a power plant, broadcast station, TV tower, or remote controller of home electronic appliances.

The keyless entry system does not oper- ate when the key is inserted in the ignition switch.

200898

: Rear gate unlock button : Unlock/disarm button : Lock/arm button

A: Panic button 1) Front 2) Back

A3120BE-B.book 9 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:132) Locking the doors

(cid:132) Unlocking the doors

(cid:132) Unlocking the rear gate

Keys and doors 2-9

200899

200900

200901

Press the “ ” button to lock all doors and rear gate. An electronic chirp will sound once and the turn signal lights will flash once. If any of the doors (or the rear gate) is not fully closed, an electronic chirp will sound five times and the turn signal lights will flash five times to alert you that the doors (or the rear gate) are not properly closed. When you close the door, it will automati- cally lock and then an electronic chirp will sound once and the turn signal lights will flash once.

Press the “ ” button to unlock the driv- er’s door. An electronic chirp will sound twice and the turn signal lights will flash twice. To unlock all doors and the rear gate, briefly press the “ ” button a second time within 5 seconds. NOTE If the interval between the first and sec- ond presses of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the sys- tem may not respond.

” button opens the

Pressing the “ rear gate. An electronic chirp will sound twice and the turn signal lights will flash twice.

(cid:132) Illuminated entry The interior (map, dome and cargo area) light will illuminate when the “ ” button is pressed. This light stays illuminated for approximately 30 seconds if any of the doors or the rear gate is not opened. If the “ ” button is pressed before 30
seconds have elapsed, this light will go out. To activate this function, set the following interior light switches to the indicated po- sitions:

– CONTINUED –

A3120BE-B.book 10 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-10 Keys and doors

Map light: OFF position Dome light: Middle position Cargo area light: DOOR position A SUBARU dealer can change the illumi- nation period setting of the interior light in accordance with your preference. Contact the nearest SUBARU dealer for details.

(cid:132) Vehicle finder function Use this function to find your vehicle parked among many vehicles in a large parking lot. Provided you are within 30
feet (10 meters) of the vehicle, pressing the “ ” button three times in a five-sec- ond period will cause your vehicle’s horn to sound once and its turn signal lights to flash three times. NOTE If the interval between presses is too short when you press the “ ” button three times, the system may not re- spond to the signals from the remote transmitter.

(cid:132) Sounding a panic alarm

200714

A “PANIC” button is located on the back of the transmitter. To activate the alarm, press the “PANIC” button once. The horn will sound and the turn signal lights will flash. To deactivate the panic alarm, press any button on the remote transmitter. Unless a button on the remote is pressed, the alarm will be deactivated after approximately 30
seconds.

the audible signal off. Do the following to deactivate the audible signal. You can also use the same steps to restore the function. 1. Sit in the driver’s seat and shut all doors and the rear gate. 2. Hold down the UNLOCK side of the power door locking switch. 3. While holding down the “UNLOCK” side of the power door locking switch, pull the key out and re-insert it into the ignition switch at least 6 times within 10 seconds after Step 2. 4. While still holding down the UNLOCK side of the power door locking switch, open and close the driver’s door once within 10 seconds after Step 3. 5. The turn signal lights flash 3 times to in- dicate completion of the setting.

You may have the above settings done by your SUBARU dealer.

(cid:132) Replacing the battery

(cid:132) Selecting audible signal op-

eration

Using an electronic chirp, the system will give you an audible signal when the doors lock and unlock. If desired, you may turn

Do not let dust, oil or water get on or in the transmitter when replacing the battery.

When the transmitter battery begins to get weak, transmitter range will begin to de-

A3120BE-B.book 11 ページ ２００６年５月３０日　火曜日　午前９時３２分

crease. Replace the battery as soon as possible. To replace the battery:

er.

200717

200715

1) Negative (–) side facing up

1. Open the transmitter case using a flat- head screwdriver.

2. Remove the old battery from the hold-

200716

3. Replace with a new battery (Type CR2025 or equivalent) making sure to in- stall the new battery with the negative (–) side facing up. 4. Refit the removed half of the transmit- ter case. After the battery is replaced, the trans- mitter must be synchronized with the keyless entry system’s control unit. Press either the “ ” button six times to synchronize the unit.

” or “

(cid:132) Replacing lost transmitters If you lose a transmitter or want to pur- chase additional transmitters (up to four

Keys and doors 2-11

can be programmed), you should re-pro- gram all of your transmitters for security reasons. It is recommended that you have your dealer program all of your transmit- ters into your system. (cid:84) Programming the transmitters The keyless entry system is equipped with a special code learning feature that allows you to program new transmitter codes into the system or to delete old ones. The sys- tem can learn up to four unique transmitter codes. The four transmitter codes may be the same or different. Programming transmitter codes into system:

Bag containing transmitter

200718

– CONTINUED –

A3120BE-B.book 12 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-12 Keys and doors

then turn it from the “LOCK” position to the “ON” position 10 times within 15
seconds.

NOTE (cid:121) When you complete step 2), an elec- tronic tone will sound once, a buzzer will continue to sound and the interior light will continue to flash until the transmitter codes are completely regis- tered. (cid:121) If you do not perform steps 1) and 2) within 45 seconds, an error will occur. Neither an electronic tone nor the buzz- er will sound, and the interior lamp will not flash. In this event, perform the whole procedure again beginning with part 1.

4. Open and close the door once within 15 seconds. NOTE (cid:121) When part 4 of the procedure is com- pleted, an electronic tone will sound for 30 seconds. (cid:121) If you do not perform the operations in part 4 within 15 seconds, an error will occur and the electronic tone will not sound. In this event, perform the registration steps again beginning with part 3 of the procedure.

200719

200720

Transmitter circuit board

To register a new transmitter with the key- less entry system, it is necessary to pro- gram the transmitter’s code (identification number) into the system. A label showing the code is affixed to the bag containing the transmitter, and another is affixed to the circuit board inside the transmitter. If there is no bag, open the transmitter case and make a note of the eight-digit number. Program the number into the system in accordance with the following procedure: 1. Firmly close the doors and the rear gate or trunk lid. 2. Open the driver’s door, sit on the driv- er’s seat, and close the door. 3. Perform the following steps within 45
seconds.

1)Open and close the driver’s door once.

200721

1) LOCK 2) ON

2)Insert the key into the ignition switch,

A3120BE-B.book 13 ページ ２００６年５月３０日　火曜日　午前９時３２分

the knob and the next exceeds 5 sec- onds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.

200722

5. Before the electronic tone stops sound- ing, push the “ ” side of the power door locking switch the same number of times as the leftmost digit of the transmitter code. For example, push the locking switch eight times if the leftmost digit of the code is 8. NOTE (cid:121) The electronic tone will stop sound- ing when you start entering the num- ber. (cid:121) If you do not start entering the num- ber using the lock knob before the electronic tone stops sounding, an er- ror will occur. In this event, perform the registration steps again beginning with part 3 of the procedure. (cid:121) If the interval between one push of

200723

6. When you have finished entering the number, push the “ ” side of the lock- ing switch within 5 seconds. NOTE (cid:121) An electronic tone will sound. (cid:121) If you push the “ ” side of the locking switch when more than 5 sec- onds have passed, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the proce- dure again starting with part 3.

Keys and doors 2-13

7. Perform parts 5 and 6 of the procedure for each of the remaining digits of the transmitter code beginning with the sec- ond digit (counting from the left) and fin- ishing with the eighth digit. NOTE (cid:121) When you finish entering the eighth digit, an electronic tone will sound for 30 seconds. (cid:121) If the interval between one push of the switch and the next exceeds 5 sec- onds, an error will occur. In this event, perform the procedure again beginning with part 4. If an error occurs six times, perform the procedure again starting with part 3.

8. Before the electronic tone stops sound- ing, use the power door locking switch to reenter the transmitter code beginning with the leftmost digit. NOTE If you do not start entering the number using the lock knob before the elec- tronic tone stops sounding, an error will occur. In this event, perform the procedure again beginning with part 3.

9. When you have finished entering the code a second time, an electronic tone will sound for one second and automatic door locking and unlocking operation will take

– CONTINUED –

A3120BE-B.book 14 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-14 Keys and doors

place once to indicate completion of regis- tration, provided the code entered the sec- ond time is identical to that entered the first time. NOTE If the code entered the second time is not identical to the code entered the first time, an error will occur. In this event, perform the procedure again be- ginning with part 5. If an error occurs five times, perform the procedure again starting with part 3.

10.If you wish to program another trans- mitter code into the system (up to four transmitter codes can be programmed into the system), perform the procedure beginning with part 4. When you have fin- ished programming all of the necessary transmitter codes into the system, remove the key from the ignition switch. 11.Test every registered transmitter to confirm correct operation.

(cid:84) Deleting old transmitter codes The control unit of the keyless entry sys- tem has four memory locations to store transmitter codes, giving it the ability to operate with up to four transmitters. When you lose a transmitter, the lost transmit- ter’s code remains in the memory. For se- curity reasons, lost transmitter codes

should be deleted from the memory. To delete old transmitter codes, program four transmitter codes into the system. If you have only one current transmitter, program it four times. If you have two cur- rent transmitters, program each one twice. If you have three current transmitters, pro- gram two of them once and the third one twice. This process will leave only current transmitter codes in the system’s memory. NOTE Make sure no one else is operating their keyless entry system within range of your vehicle when programming transmitters. If someone else were to operate their remote transmitter while you are programming your transmit- ters, it is possible that their transmitter code will be programmed into your system, allowing them unauthorized access to your vehicle.

Alarm system

The alarm system helps to protect your vehicle and valuables from theft. The horn sounds and the turn signal lights flash if someone attempts to break into your vehi- cle.

The system can be armed and disarmed with the remote transmitter. The system does not operate when the key is inserted into the ignition switch.

Your vehicle’s alarm system has been set for activation at the time of shipment from the factory. You can set the system for de- activation yourself or have it done by your SUBARU dealer.

(cid:132) System operation The alarm system will give the following alarms when triggered: (cid:121) The vehicle’s horn will sound and the turn signal lights will flash for 30 seconds. (cid:121) If any door (or the rear gate) remains open after the 30-second period, the horn will continue to sound for a maximum of 3
minutes. If the door (or the rear gate) is closed while the horn is sounding, the horn will stop sounding with a delay of up to 30 seconds.

The alarm is triggered by:

A3120BE-B.book 15 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:121) Opening a door or the rear gate (cid:121) Physical impact to the vehicle, such as forced entry (only vehicles with shock sen- sors (dealer option))

(cid:132) Activating and deactivating

the alarm system

To change the setting of your vehicle’s alarm system for activation or deactiva- tion, do the following. 1. Disarm the alarm system (see “Disarm- ing the system” in this section). 2. Sit in the driver’s seat and shut all doors (and the rear gate). 3. Turn the ignition switch to the “ON” po- sition. 4. Hold down the UNLOCK side of the driver’s power door locking switch, open the driver’s door within the following 1 sec- ond, and wait 10 seconds without releas- ing the switch. The setting will then be changed as follows:

If the system was previously activated: The odometer/trip meter screen displays “AL oF” and the horn sounds twice, indi- cating that the system is now deactivated.

If the system was previously deactivated: The odometer/trip meter screen displays “AL on” and the horn sounds once, indi- cating that the system is now activated.

NOTE You may have the above setting change done by your SUBARU dealer.

(cid:132) If you have accidentally trig-

gered the alarm system

(cid:84) To stop the alarm Do any of the following operations: (cid:121) Press any button on the remote trans- mitter. (cid:121) Turn the ignition switch to the “ON” po- sition.

(cid:132) Arming the system (cid:84) To arm the system using remote

transmitter

1. Close all windows and the moonroof. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehi- cle. 4. Make sure that the engine hood is locked. 5. Close all doors (and the rear gate).

Keys and doors 2-15

200918

: Press to Arm the system. : Press to Disarm the system.

200702

6. Briefly press the “ ” button (for less than two seconds). All doors (and the rear gate) will lock, an electronic chirp will

– CONTINUED –

A3120BE-B.book 16 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-16 Keys and doors

sound once, the turn signal lights will flash once and the indicator lights will start flashing rapidly. After rapid flashing for 30
seconds (standby time), the indicator lights will then flash slowly (twice approxi- mately every two seconds), indicating that the system has been armed for surveil- lance.

If any of the doors, (or the rear gate) is not fully closed, an electronic chirp sounds five times, the turn signal lights flash five times to alert you that the doors (or the rear gate) are not properly closed. When you close the door, the system will auto- matically arm and doors will automatically lock.

(cid:84) To arm the system using power

door locking switches

1. Close all windows. 2. Remove the key from the ignition switch. 3. Open the doors and get out of the vehi- cle. 4. Make sure that the engine hood is locked. 5. Close the doors and the rear gate but leave only the driver’s door or the front passenger’s door open.

(cid:121) The system is in the standby mode for a 30-second period after locking the doors with the remote transmitter. The security indicator light will flash at short intervals during this period. (cid:121) If any of the following actions is done during the standby period, the system will not switch to the surveillance state. (cid:121) Doors are unlocked using the re- mote transmitter. (cid:121) Any door (including the rear gate) is opened. (cid:121) Ignition switch is turned to the “ON” position.

(cid:132) Disarming the system Briefly press the “ ” button (for less than two seconds) on the remote transmit- ter. The driver’s door will unlock, an elec- tronic chirp will sound twice, the turn sig- nal lights will flash twice and the indicator light will go off.

To unlock all other doors and the rear gate, briefly press the “ ” button a second time within 5 seconds. NOTE If the interval between the first and sec- ond presses of the “ ” button (for unlocking of all of the doors and the rear gate) is extremely short, the sys-

200705

6. Push the front side (“LOCK” side) of the power door locking switch to set the door locks. 7. Close the door. An electronic chirp will sound once, the turn signal lights will flash once and the indicator light will start flash- ing slowly (approximately once every two seconds) to inform you that the system has armed. NOTE (cid:121) The system can be armed even if the engine hood, the windows and/or moonroofs are opened. Always make sure that they are fully closed before arming the system. (cid:121) The 30-second standby time can be eliminated if you prefer. Have it per- formed by your SUBARU dealer.

A3120BE-B.book 17 ページ ２００６年５月３０日　火曜日　午前９時３２分

tem may not respond.

(cid:84) Emergency disarming If you cannot disarm the system using the transmitter (i.e. the transmitter is lost, bro- ken or the transmitter battery is too weak), you can disarm the system without using the transmitter. The system can be disarmed if you turn the ignition switch from the “LOCK” to the “ON” position with a registered key.

(cid:132) Valet mode When you choose the valet mode, the alarm system does not operate. In valet mode, the remote transmitter is used only for locking and unlocking the doors and rear gate and panic activation.

To enter the valet mode, change the set- ting of your vehicle’s alarm system for de- activation mode. (Refer to “Activating and deactivating the alarm system” in this sec- tion.) The security indicator light will con- tinue to flash once every three seconds in- dicating that the system is in the valet mode.

To exit valet mode, change the setting of your vehicle’s alarm system for activation mode. (Refer to “Activating and deactivat- ing the alarm system” in this section.)

(cid:132) Passive arming When passive arming mode has been programmed by the dealer, arming of the system is automatically accomplished without using the remote transmitter. Note that in this mode, DOORS MUST BE MANUALLY LOCKED. (cid:84) To enter the passive mode If you wish to program the passive arming mode, have it done by your SUBARU dealer. (cid:84) Arming the system

In passive mode, the system will au- tomatically activate the alarm but WILL NOT automatically lock the doors. In order to lock the doors you must either lock them as indicated in step 4 below or with the key once they have been closed. Failure to lock the doors manually will result in a higher security risk.

1. Turn the ignition switch to the “ON” po- sition.

Keys and doors 2-17

200721

1) LOCK 2) ON

2. Turn the ignition switch from “ON” to “LOCK” position and remove the key from the ignition switch. 3. Open the doors and get out of the vehi- cle.

– CONTINUED –

A3120BE-B.book 18 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-18 Keys and doors

(cid:132) Tripped sensor identification The security indicator light flashes when the alarm system has been triggered. Al- so, the number of flashes indicates the lo- cation of unauthorized intrusion or the se- verity of impact on the vehicle. (cid:121) When the ignition switch is turned to the “ON” position, the indicator light will light for 1 second and then flash as follows:

When a door or rear gate was opened: 5 times When the ignition switch was turned to the “ON” position by using a key not reg- istered with your immobilizer system: 3
times When a strong impact or multiple im- pacts were sensed: twice (only vehicles with shock sensors (dealer option)) When a light impact was sensed: once (only vehicles with shock sensors (deal- er option))

(cid:132) Shock sensors (dealer op-

tion)

The shock sensors trigger the alarm sys- tem when they sense impacts applied to the vehicle and when any of their electric wires is cut. The alarm system causes the horn to sound and the turn signal lights to flash for a short time when the sensed im- pact is weak, but it warns of a strong im-

200704

4. Before closing the doors, lock all doors with the inside door lock levers. 5. Close the doors. The system will auto- matically arm after one minute.

In the passive mode, the system can also be armed with the remote transmitter or with the power door locking switches. If the remote transmitter or power door lock- ing switch is used to lock the vehicle, arm- ing will take place immediately regardless of whether or not the passive mode has been selected.

(cid:84) Disarming the system To disarm the system, briefly press the “

” button on the transmitter.

pact or multiple impacts by sounding the horn and flashing the turn signal lights, both lasting approximately 30 seconds. If you desire, your SUBARU dealer can connect them and set them for activation or deactivation. NOTE (cid:121) The shock sensors are not always able to sense impacts caused by breaking in, and cannot sense an im- pact that does not cause vibration (such as breaking the glass using a rescue hammer). (cid:121) The shock sensors may sense vibra- tion like those shown in the following and trigger the alarm system. Select the settings of the alarm system and shock sensors appropriately depend- ing on where you usually park your ve- hicle. Example:

Vibration from construction site Vibration in multistory car park Vibration from trains

(cid:121) You can have the sensitivity of the shock sensors adjusted to your prefer- ence by your SUBARU dealer.

A3120BE-B.book 19 ページ ２００６年５月３０日　火曜日　午前９時３２分

Child safety locks

Windows

(cid:84) Driver’s side switches

Keys and doors 2-19

Always use the child safety lock whenever a child rides in the rear. Serious injury could result if a child accidentally opened the door and fell out.

LOCK

200726

Each rear door has a child safety lock that prevents the doors from being opened even if the inside door handle is pulled.

When the child safety lock lever is in the lock position, the door cannot be opened from inside regardless of the position of the inner door handle lock lever. The door can only be opened from the outside.

(cid:132) Power windows

To avoid serious personal injury caused by entrapment, you must do the following. (cid:121) When operating the power win- dows, be extremely careful to pre- vent anyone’s fingers, arms, neck or head from being caught in the window.

(cid:121) Always lock the passengers’ win- dows using the lock switch when children are riding in the vehicle. (cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the power win- dow.

The power windows operate only when the ignition switch is in the “ON” position.

200727

1) Lock switch 2) For driver’s window 3) For front passenger’s window 4) For rear left window 5) For rear right window

All door windows can be controlled by the power window switch cluster at the driver side door.

– CONTINUED –

A3120BE-B.book 20 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-20 Keys and doors

(cid:86) Operating the driver’s window

200728

1) Open 2) Automatically open

To open: Push the switch down lightly and hold it. The window will open as long as the switch is held. This switch also has a one-touch auto down feature that allows the window to be opened fully without holding the switch. Push the switch down until it clicks and re- lease it, and the window will fully open. To stop the window halfway, pull the switch up lightly.

To open the passengers’ windows, push the appropriate switch down and hold it until the window reaches the desired posi- tion.

200729

To close: Pull the switch up lightly and hold it. The window will close as long as the switch is held. (cid:86) Operating the passengers’ windows

200731

To close the window, pull the switch up and hold it until it reaches the desired po- sition.

200730

A3120BE-B.book 21 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:86) Locking the passengers’ windows

(cid:84) Passengers’ side switches

Keys and doors 2-21

200732

200733

Front passenger’s window switch 1) Open 2) Close

To open the window, push the switch down and hold it until the window reaches the desired position.

To lock the passengers’ windows, push the lock switch. When the lock switch is in the “LOCK” position, the passengers’ win- dows cannot be opened or closed. Press the switch again to cancel the pas- sengers’ window locking. NOTE When the lock switch is pushed to the “LOCK” position, the indicator lights in the passenger’s window switches (in- cluded in the power window switch cluster on the driver’s door) all go out.

200734

Rear passengers’ window switches 1) Open 2) Close

To close the window, pull the switch up and hold it until the window reaches the desired position.

When the lock switch on the power win- dow switch cluster, located on the driver’s side door, is in the “LOCK” position, the passengers’ windows cannot be operated with the passengers’ switches.

A3120BE-B.book 22 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-22 Keys and doors

Rear gate

200736

200894

200735

The rear gate can be locked and unlocked using either the keyless entry system or the power door locking switch. Refer to the “Power door locking switches” and “Remote keyless entry system” sec- tions in this chapter. To open the rear gate, first unlock the rear gate lock then push the button.

To close the rear gate, lower it slowly and push down firmly until the latch engages. The rear gate can be lowered easily if you pull it down holding the recessed grip.

(cid:121) To prevent dangerous exhaust gas from entering the vehicle, al- ways keep the rear gate closed while driving.

(cid:121) Do not attempt to shut the rear gate while holding the recessed grip. Also avoid closing the rear gate by pulling on the recessed grip from inside the cargo space. There is a danger of your hand be- ing caught and injured.

1) Reflectors

When the rear gate is open, do not place a heavy item on either reflec- tor. Also, do not sit on either reflec- tor. Doing so could break the reflec- tor.

A3120BE-B.book 23 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:121) Do not jam a plastic bag in or place cellophane tape on the rear gate stays or scratch the stays while loading or unloading cargo. That could cause leakage of gas from the stays, which may result in their inability to hold the rear gate open.

(cid:121) Be careful not to hit your head or face on the rear gate when open- ing or closing the rear gate and when loading or unloading cargo.

NOTE Should the rear gate be unable to be unlocked due to a discharged battery, a fault in the door locking/unlocking system or other causes, you can un- lock it by manually operating the rear gate lock release lever. For the procedure, refer to “Rear gate – if the rear gate cannot be unlocked” section in chapter 9.

Moonroof (if equipped)

(cid:121) Never let anyone’s hands, arms, head or any objects protrude from the moonroof. A person could be seriously injured if the vehicle stops suddenly or turns sharply or if the vehicle is involved in an accident. To avoid serious personal injury caused by entrapment, you must do the following. (cid:121) Before closing

the moonroof, make sure that no one’s hands, arms, head or other objects will be accidentally caught in the moon- roof.

(cid:121) Before leaving the vehicle, always remove the key from the ignition switch for safety and never allow an unattended child to remain in the vehicle. Failure to follow this procedure could result in injury to a child operating the moonroof.

(cid:121) Never try to check the anti-entrap- ment function by deliberately placing part of your body in the moonroof.

Keys and doors 2-23

(cid:121) Do not sit on the edge of the open

moonroof.

(cid:121) Do not operate the moonroof if falling snow or extremely cold conditions have caused it to freeze shut.

(cid:121) The

anti-entrapment

function does not operate when the moon- roof is being tilted down. Be sure to confirm that it is safe to do so before tilting the moonroof down.

The moonroof has both tilting and sliding functions.

The moonroof operates only when the ig- nition switch is in the “ON” position.

– CONTINUED –

A3120BE-B.book 24 ページ ２００６年５月３０日　火曜日　午前９時３２分

2-24 Keys and doors

(cid:132) Tilt function

200737

1) Tilt up 2) Tilt down

The tilting function will only operate when the moonroof is fully closed.

Push the rear side of the “Tilt” switch to raise the moonroof. Push the front side of the “Tilt” switch to lower the moonroof.

Release the switch after the moonroof has been raised or has been lowered com- pletely. Pushing the switch continuously may cause damage to the moonroof. NOTE One-touch operation does not take place when the moonroof is tilted up

and down. Push the switch continu- ously to tilt the moonroof up and down.

(cid:132) Sliding function

200738

1) Open 2) Close

Push the “Open/Close” switch rearward to open the moonroof. The sun shade will also be opened together with the moon- roof. Push the “Open/Close” switch forward to close the moonroof. The moonroof will stop halfway. Push it again to close the moonroof completely. To stop the moonroof at a selected mid- way position while opening or closing it, momentarily push the “OPEN” or “CLOSE” side.

the switch

to

After washing the vehicle or after it rains, wipe away water on the roof prior to open- ing the moonroof to prevent drops of water from falling into the passenger compart- ment.

(cid:132) Anti-entrapment function When the moonroof senses an object trapped between its glass and the vehi- cle’s roof during closure, it automatically moves back to either of the following posi- tions according to the point at which it senses the object: (cid:121) When the moonroof senses the object at a point between the halfway stop posi- tion and fully closed position, it moves back to the halfway stop position and stops there. (cid:121) When the moonroof senses the object at a point between the halfway stop posi- tion and fully open position, it moves back to the fully open position and stops there.

The anti-entrapment function may also be activated by a strong shock on the moon- roof even when there is nothing trapped. NOTE For the sake of safety, it is recommend- ed that you avoid driving with the moonroof fully opened.

A3120BE-B.book 25 ページ ２００６年５月３０日　火曜日　午前９時３２分

(cid:132) Sun shade

Keys and doors 2-25

200739

The sun shade can be slid forward or backward by hand while the moonroof is closed. If the moonroof is opened, the sun shade also moves back.

A3120BE-B.book 26 ページ ２００６年５月３０日　火曜日　午前９時３２分

A3120BE-B.book 1 ページ ２００６年５月３０日　火曜日　午前９時３２分

Instruments and controls

Ignition switch .................................................... LOCK ...................................................................... ACC .......................................................................... ON ............................................................................ START ...................................................................... Key reminder chime ............................................... Ignition switch light ................................................ Hazard warning flasher ...................................... Meters and gauges ............................................. Combination meter illumination ............................ Canceling the function for meter needle/

gauge movement and combination meter sequential illumination upon turning on the ignition switch ...................................................... Speedometer ........................................................... Odometer ................................................................. Double trip meter .................................................... Tachometer ............................................................. Fuel gauge ............................................................... Temperature gauge ................................................ Warning and indicator lights ............................. Seatbelt warning light and chime .......................... SRS airbag system warning light .......................... Front passenger’s frontal airbag ON and OFF

indicators ..............................................................

CHECK ENGINE warning light/Malfunction

indicator lamp ....................................................... Charge warning light .............................................. Oil pressure warning light ..................................... AT OIL TEMPerature warning light .......................

3-3
3-3
3-4
3-4
3-4
3-5
3-5
3-5
3-5
3-5

3-6
3-7
3-7
3-7
3-8
3-8
3-9
3-9
3-10
3-11

3-12

3-13
3-13
3-13
3-14

Rear differential oil temperature warning

light ........................................................................ Low tire pressure warning light ............................ ABS warning light ................................................... Brake system warning light ................................... Low fuel warning light ............................................ Door open warning light ........................................ Windshield washer fluid warning light ................. All-Wheel Drive warning light ................................ Vehicle Dynamics Control operation indicator