Login- 2012 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- 2008 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- 2007 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- 2006 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- 2010 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- 2011 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- 2009 Subaru Tribeca Owners Manuals
- Subaru Tribeca Owners Manuals
- Download PDF Manual
-
(5°C) or higher. (cid:121) The vehicle speed remains at 9 mph (15
km/h) or lower for 15 minutes. (cid:121) The battery voltage decreases below the permissible level.Windshield wiper deicer
300515
The windshield wiper deicer operates only when the ignition switch is in the “ON” po- sition.
Before turning on the windshield wiper de- icer, remove any snow from the wind- shield. To turn on the windshield wiper de- icer, push the button. The indicator light located on the button lights up while the windshield wiper deicer is operating. The windshield wiper deicer will automati- cally shut off after approximately 15 min- utes. If the windshield wiper blades have been deiced completely before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If deicing is not
Instruments and controls 3-33
Rear window defogger but- ton
300522
The rear window defogger operates only when the ignition switch is in the “ON” po- sition. The rear window defogger button is locat- ed on the climate control panel.
To turn on the defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the rear window defogger is operating.
The defogger will automatically shut off af- ter approximately 15 minutes. If the win- dow clears before that time, push the but- ton to turn it off. It also turns off when the
– CONTINUED –
A3120BE-B.book 34 ページ ２００６年５月３０日 火曜日 午前９時３２分
3-34 Instruments and controls
ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is desired when you restart your vehicle, you have to push the button to turn it on again. Your SUBARU dealer can set your rear window defogger for continuous opera- tion. Contact your SUBARU dealer for de- tails.
Once the rear window defogger has been set for continuous operation, the rear win- dow defogger repeatedly operates for 15
minutes, stops for two minutes, and again operates for 15 minutes. If the battery volt- age drops below the permissible level, continuous operation is canceled and op- eration stops as described in the follow- ing. (cid:121) If the battery voltage drops below the permissible level within 15 minutes of de- pression of the button, continuous opera- tion is canceled and the rear window de- fogger stops operating 15 minutes later. (cid:121) If the battery voltage drops below the permissible level after the rear window de- fogger has, following depression of the button, operated for 15 minutes, stopped operating for two minutes, and started op- erating again, the rear window defogger immediately stops operating.(cid:121) Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the rear window. They may dam- age the conductors printed on the window.
(cid:121) To prevent the battery from being discharged, do not operate the de- fogger continuously for any long- er than necessary.
NOTE If your vehicle is equipped with the out- side mirror defogger, the outside mir- ror defogger operates while the rear window defogger is operating.
Mirrors
Always check that the inside and outside mirrors are properly adjusted before you start driving.
(cid:132) Inside mirror
300516
The inside mirror has a day and night po- sition. Pull the tab at the bottom of the mir- ror toward you for the night position. Push it away for the day position. The night po- sition reduces glare from headlights.
A3120BE-B.book 35 ページ ２００６年５月３０日 火曜日 午前９時３２分
(cid:132) Auto-dimming mirror/com-
pass (if equipped)
ton, the compass display is toggled on or off. When the compass is on, an illuminat- ed compass reading will appear in the lower part of the mirror.
cover the sensors with stickers, or other similar items. Periodically wipe the sen- sors clean using a piece of dry soft cotton cloth or an applicator.
Instruments and controls 3-35
300517
1) Left button 2) Auto dimming indicator 3) Photosensor 4) Right button
The auto-dimming mirror/compass has an anti-glare feature which automatically re- duces glare coming from headlights of ve- hicles behind you. It also contains a built- in compass. (cid:121) By pressing and releasing the left but- ton, the automatic dimming function is tog- gled on or off. When the automatic dim- ming function is on, the auto dimming indi- cator light (green) located to the right of the button will illuminate. (cid:121) By pressing and releasing the right but-
Even with the mirror in anti-glare mode, the mirror surface turns bright if the trans- mission is shifted into reverse. This is to ensure good rearward visibility during re- versing. (cid:84) Photosensors
300518
The mirror has a photosensor attached on both the front and back sides. If the glare from the headlights of vehicles behind you strikes the mirror, these sensors detect it and make the reflection surface of the mir- ror dimmer to help prevent you from being blinded. For this reason, use care not to
(cid:84) Compass calibration 1. For optimum calibration, switch off all nonessential electrical accessories (rear window defogger, heater/air conditioning system, spotlight, etc.) and ensure all doors are shut. 2. Drive to an open, level area away from large metallic objects or structures and make certain the ignition switch is in the “ON” position. 3. Press and hold the left button for 3 sec- onds then release, and the compass will enter the calibration mode. “CAL” and di- rection will be displayed. 4. Drive slowly in a circle until “CAL” dis- appears from the display (approximately two or three circles). The compass is now calibrated. 5. Further calibration may be necessary should outside influences cause the mirror to read inaccurately. You will know that this has occurred if your compass begins to read in only limited directions. Should you encounter this situation, return to step one of the above procedure and recali- brate the mirror.
– CONTINUED –
A3120BE-B.book 36 ページ ２００６年５月３０日 火曜日 午前９時３２分
3-36 Instruments and controls
(cid:84) Compass zone adjustment 1. The zone setting is factory preset to Zone 8. Refer to the “Compass calibration zone” map attached to the end of this manual to verify that the compass zone setting is correct for your geographical lo- cation. 2. Press and hold the right button for 3
seconds then release, and the word “ZONE” will briefly appear and then the zone number will be displayed. 3. Press the right-hand button repeatedly to cycle the display through all possible zone settings. Stop cycling when the cor- rect zone setting for your location is dis- played. 4. Releasing the button for 3 seconds will exit the zone setting mode.(cid:132) Outside mirrors (cid:84) Convex mirror (Passenger side)
Objects look smaller in a convex mirror and farther away than when viewed in a flat mirror. Do not use the convex mirror to judge the dis- tance of vehicles behind you when changing lanes. Use the inside mir- ror (or glance backwards) to deter- mine the actual size and distance of objects that you view in convex mir- ror.
(cid:84) Remote control mirror switch
when the ignition switch is in the “ON” or “ACC” position. 1. Turn the knob to the “L” side to adjust the left-hand mirror or to the “R” side to ad- just the right-hand mirror. 2. Move the knob in the direction you want to move the mirror. 3. Return the knob to the neutral position to prevent unintentional operation.
The mirrors can also be adjusted manual- ly. (cid:84) Outside mirror defogger
The remote control mirrors operate only
300519
300522
The outside mirror defogger shares the button with rear window defogger. The outside mirror defogger operates only when the ignition switch is in the “ON” po- sition.
A3120BE-B.book 37 ページ ２００６年５月３０日 火曜日 午前９時３２分
To turn on the outside mirror defogger, push the button. To turn it off, push the button again. The indicator light located on the button lights up while the outside mirror defogger is op- erating.
The defogger will automatically shut off af- ter approximately 15 minutes. If the mirror clears before that time, push the button to turn it off. It also turns off when the ignition switch is turned to the “ACC” or “LOCK” position. If defrosting or defogging is de- sired when you restart your vehicle, you have to push the button to turn it on again. NOTE (cid:121) While the outside mirror defogger is operating, the rear window defogger also operates. (cid:121) When the rear window defogger has been set for continuous operation, the outside mirror defogger also operates continuously. Refer to the “Rear win- dow defogger button” section in this chapter.
To prevent the battery from being discharged, do not operate the de- fogger continuously for any longer than necessary.
Tilt steering wheel
Horn
Do not adjust the steering wheel tilt position while driving. This may cause loss of vehicle control and re- sult in personal injury.
Instruments and controls 3-37
To sound the horn, push the horn pad.
300521
300520
1. Adjust the seat position. Refer to the “Front seats” section (chapter 1). 2. Pull the tilt lock lever down. 3. Move the steering wheel to the desired level. 4. Push the lever up to lock the steering wheel in place. 5. Make sure that the steering wheel is securely locked by moving it up and down.
A3120BE-B.book 38 ページ ２００６年５月３０日 火曜日 午前９時３２分
A3120BE-B.book 1 ページ ２００６年５月３０日 火曜日 午前９時３２分
Climate control
Ventilator ............................................................. Air flow ..................................................................... Ventilator ................................................................. Automatic climate control system .................... Control panel ........................................................... Rear air conditioner (if equipped) ......................... Temperature sensors .............................................
4-2
4-2
4-4
4-5
4-5
4-9
4-9Operating tips for heater and
air conditioner ................................................. 4-10
Cleaning ventilator grille ........................................ 4-10
Efficient cooling after parking in directsunlight .................................................................
4-10
Lubrication oil circulation in the refrigerant
circuit .....................................................................
Checking air conditioning system before
summer season .................................................... Cooling and dehumidifying in high humidity and low temperature weather conditions ..................
Air conditioner compressor shut-off when
4-10
4-10
4-10
engine is heavily loaded ...................................... Refrigerant for your climate control system ........
4-10
4-10
Air filtration system ............................................ 4-11
4-11Replacing the air filter ............................................
A3120BE-B.book 2 ページ ２００６年５月３０日 火曜日 午前９時３２分
4-2 Climate control
Ventilator
(cid:132) Air flow
Climate control
400739
A3120BE-B.book 3 ページ ２００６年５月３０日 火曜日 午前９時３２分
(cid:84) Air flow mode selection
Climate control 4-3
400740
– CONTINUED –
A3120BE-B.book 4 ページ ２００６年５月３０日 火曜日 午前９時３２分
4-4 Climate control
(cid:132) Ventilator (cid:84) Center ventilators
(cid:84) Side ventilator
(cid:84) Rear ventilators (if equipped)
Move the tab up and down or right and left to adjust the flow direction.
400503
1) Open 2) Close
400504
400505
Move the tab up and down or right and left to adjust the flow direction.
Move the tab up and down or right and left to adjust the flow direction. To open the ventilator, turn the side grille open/close wheel upward. To close it, turn the wheel downward.
A3120BE-B.book 5 ページ ２００６年５月３０日 火曜日 午前９時３２分
Automatic climate control system
NOTE (cid:121) Operate the automatic climate con- trol system when the engine is run- ning. (cid:121) The blower fan rotates at a low speed when the engine coolant temperature is low. For efficient defogging or dehumidify- ing in cold weather, press the “A/C” button. (cid:121) Even when cooling is not necessary, setting the temperature much lower than the current outlet air temperature turns on the air conditioner compres- sor automatically and the “A/C” indica- tor light on the control panel comes on. (cid:121) Seven-seater models each have a rear air conditioner. The fan speed of the rear air conditioner can be adjust- ed, but other adjustments (outlet air temperature, air distribution, etc.) are not possible for the rear air condition- er. For details, refer to “Rear air condi- tioner (if equipped)” in this section.
The automatic climate control system au- tomatically controls outlet air temperature, fan speed, air flow distribution air-inlet control, and air conditioner compressor
Climate control 4-5
operation. It activates when the “AUTO” button is pressed, and is used to maintain a constant, comfortable climate within the passenger compartment. The temperature can be set within a range of 65 to 85°F (18 to 32°C).
9) OFF button 10)AUTO button
(cid:84) AUTO button AUTO mode operation:
(cid:132) Control panel
10 9
400506
1) Temperature control dial (driver’s side) 2) Defroster button 3) Fan speed control dial 4) Rear window defogger button (Refer to
the “Rear window defogger button” in chapter 3.)
5) Temperature control dial (passenger’s
side)
6) Air conditioner button 7) Air flow mode selection button 8) Air inlet selection button
400507
When the “AUTO” button is pressed, the indicator light on the button comes on. In this state, fan speed, air flow distribution, air-inlet control, and air conditioner com- pressor operation are automatically con- trolled. Manual mode operation: If you operate any of the buttons on the control panel other than the “OFF” button and temperature control dial during auto- matic mode operation, the indicator light will go out. You can then manually control the system as desired using the button you operated.
– CONTINUED –
A3120BE-B.book 6 ページ ２００６年５月３０日 火曜日 午前９時３２分
4-6 Climate control
To change the system back to the AUTO mode, press the “AUTO” button. (cid:84) OFF button
(cid:84) Temperature control dial
Driver’s side
400508
400509
The Automatic Climate Control system turns off (the air conditioner compressor and fan turn off) when the “OFF” button is pressed. When the “OFF” button is pressed, the outside air introduction mode (air inlet se- lection OFF) is automatically selected.
400510
Passenger’s side
It is possible to make separate tempera-
ture settings for the driver’s side and pas- senger’s side. Each temperature setting is shown on the display. With the dial set at your desired temperature, the system au- tomatically adjusts the temperature of air supplied from the outlets such that the de- sired temperature is achieved and main- tained. Turning the dial counterclockwise and re- leasing it reduces the temperature by 1°F (0.5°C). Turning the dial clockwise and re- leasing it increases the temperature by 1°F (0.5°C). Holding the dial in either turned position causes the temperature to change continuously. With the minimum temperature set, the system gives maximum cooling perfor- mance. With the maximum temperature set, the system gives maximum heating performance.
A3120BE-B.book 7 ページ ２００６年５月３０日 火曜日 午前９時３２分
(cid:84) – Defroster button
defroster.
(cid:84) A/C – Air conditioner button
(cid:84) Fan speed control dial
Climate control 4-7
400511
”. When the “
To defrost or dehumidify the windshield and front door windows, push the defrost- er button “ ” button is pushed, regardless whether the air con- ditioner is operating or not, outside air is drawn into the passenger compartment, the air conditioner compressor turns on, air flow is directed towards the windshield and front door windows, and the indicator light on the button comes on. After eliminating the fogging from the windshield, return the climate control sys- tem to the AUTO mode by pushing the “AUTO” button or turn off by pushing the “OFF” button. Alternatively, push the “ ” button again to return the system to the setting that was selected before you activated the
400512
The fan speed control dial has 7 positions: AUTO position and 6 different fan speed positions. The fan speed is shown on the center of the dial. With the fan speed control dial in the AUTO position, the fan speed changes automatically corresponding the various conditions: air temperature inside and out- side of the passenger’s compartment, in- tensity of the sunlight, etc.
400513
If the windshield starts to fog when the cli- mate control system is operated in the AUTO mode, push the air conditioner but- ton to defog and dehumidify. When this button is pushed, the air condi- tioner compressor turns on and the indica- tor light on the button comes on. After eliminating the fogging from the wind- shield, set the system back to the AUTO mode by pushing the “AUTO” button. NOTE The air conditioner compressor does not operate when the outside air tem- perature is below 32°F (0°C).
– CONTINUED –
A3120BE-B.book 8 ページ ２００６年５月３０日 火曜日 午前９時３２分
4-8 Climate control
(cid:84) Air flow mode selection button
er outlets, and the foot outlets.
(cid:84) Air inlet selection button
400514
Select the desired air flow mode by push- ing the air flow mode selection button. The selected air flow mode is shown on the center of the dial.
(Ventilation): Air flows through the in-
strument panel outlets.
(Bi-level): Air flows through the instru-
ment panel outlets and the foot outlets.
(Heat): Air flows through the instru- ment panel outlets, the foot outlets, and some through the windshield defroster outlets.
(Heat-def): Air flows through the instru- ment panel outlets, the windshield defrost-
400515
ON position (Recirculation): Interior air is recirculated inside the vehicle. Push the air inlet selection button to the ON position for fast cooling with the air conditioner or when driving on a dusty road. The indica- tor light will come on. OFF position (Outside Air): Outside air is drawn into the passenger compartment. Push the air inlet selection button to the OFF position when the interior has cooled to a comfortable temperature and the road is no longer dusty. The indicator light will go off.
Continued operation in the ON posi- tion may fog up the windows. Switch to the OFF position as soon as the outside dusty condition clears. NOTE When driving on a dusty road or be- hind a vehicle that emits unpleasant exhaust gases, set the air inlet selec- tion button to the ON position. From time to time, return the air inlet selection button to the OFF position to draw outside air into the passenger compartment.
A3120BE-B.book 9 ページ ２００６年５月３０日 火曜日 午前９時３２分
(cid:132) Rear air conditioner (if
equipped)
cooled air out of the ventilators. (cid:121) The outlet air temperature of the rear air conditioner cannot be adjusted. (cid:121) The rear air conditioner cannot be used as a heater.
(cid:132) Temperature sensors
Climate control 4-9
– Do not cover the sensors.
The sensors are located as follows: – Solar sensor: beside windshield de- froster grille – Interior air temperature sensor: on the side of the driver-side part of the center panel – Outside temperature sensor: behind front grille
400516
The rear air conditioner blows cool air out of the rear ventilators while the “A/C” but- ton on the control panel is in the “ON” po- sition. The fan speed of the rear air condi- tioner can be adjusted using the rear air conditioner dial behind the center console. The fan speed can be adjusted in four steps by turning the dial. Turn the dial to the “OFF” position to stop the fan. NOTE (cid:121) When the “A/C” button is in the “OFF” position and when the “A/C” in- dicator is not illuminated during AUTO- mode operation, the air conditioner compressor does not operate, mean- ing that the system merely blows un-
400517
1) Interior air temperature sensor 2) Solar sensor
The automatic climate control system em- ploys several sensors. These sensors are delicate. If they are treated incorrectly and become damaged, the system may not be able to control the interior temperature correctly. To avoid damaging the sensors, observe the following precautions: – Do not subject the sensors to impact. – Keep water away from the sensors.
A3120BE-B.book 10 ページ ２００６年５月３０日 火曜日 午前９時３２分
4-10 Climate control
Operating tips for heater and air conditioner
(cid:132) Cleaning ventilator grille
low outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air con- ditioner for maximum cooling efficiency.
(cid:132) Lubrication oil circulation in
the refrigerant circuit
Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-season to circulate its oil.
(cid:132) Checking air conditioning
system before summer sea- son
Check the air conditioner unit for refriger- ant leaks, hose conditions, and proper op- eration each spring. Have your SUBARU dealer perform this check.
(cid:132) Cooling and dehumidifying in
high humidity and low tem- perature weather conditions Under certain weather conditions (high relative humidity, low temperatures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate
400518
Always keep the front ventilator inlet grille free of snow, leaves, or other obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is im- paired by any accumulation of insects and leaves on the condenser.
(cid:132) Efficient cooling after parking
in direct sunlight
After parking in direct sunlight, drive with the windows open for a few minutes to al-
any problem with the air conditioning sys- tem.
(cid:132) Air conditioner compressor
shut-off when engine is heavily loaded
To improve acceleration and gas mileage, the air conditioner compressor is de- signed to temporarily shut off during air conditioner operation whenever the accel- erator is fully depressed such as during rapid acceleration or when driving on a steep upgrade.
(cid:132) Refrigerant for your climate
control system
Your air conditioner uses ozone friendly refrigerant HFC134a. Therefore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.
A3120BE-B.book 11 ページ ２００６年５月３０日 火曜日 午前９時３２分
Air filtration system
Replace the filter element according to the replacement schedule shown in the fol- lowing. This schedule should be followed to maintain the filter’s dust collection abili- ty. Under extremely dusty conditions, the filter should be replaced more frequently. It is recommended that you have your fil- ter checked or replaced by your SUBARU dealer. For replacement, we recommend the use of a genuine SUBARU air filter kit.
Replacement schedule:
Every 15 months or 15,000 miles (24,000
km) whichever comes firstClimate control 4-11
1. Remove the instrument panel side cov- er. NOTE The instrument panel side cover is held in place with four pins.
3. Remove the glove box by detaching the one clip on the side.
400742
(cid:132) Replacing the air filter
400741
2. Unhook the strap.
400561
4. Remove the air filter cover by detach- ing the five clips.
400596
– CONTINUED –
A3120BE-B.book 12 ページ ２００６年５月３０日 火曜日 午前９時３２分
4-12 Climate control
400564
400741
400566
5. Unhook the air filter and draw it out.
9. Attach the strap to the hook.
400565
400742
6. Replace the air filter with a new one. 7. Install the air filter cover. 8. Install the glove box.
10.Secure the glove box with the one clip. 11.Install the instrument panel side cover.
12.Label installation Attach the caution label to the driver’s door.
Contact your SUBARU dealer if the following occurs, even if it is not yet time to change the filter: – Reduction of the air flow through
the vents.
– Windshield gets easily fogged or
misted.
NOTE The filter can influence the air condi- tioning, heating and defroster perfor- mance if not properly maintained.
A3120BE-B.book 1 ページ ２００６年５月３０日 火曜日 午前９時３２分
Audio
Antenna system .................................................. Printed antenna ....................................................... FM reception ...........................................................
5-2
5-2
5-2XMTM Satellite radio reception
(if equipped) ..................................................... Installation of accessories ................................ Audio set ............................................................. Type A audio set ..................................................... Type B audio set ..................................................... Type A audio set (if equipped) .......................... Radio operation ...................................................... Compact disc player operation .............................
5-2
5-4
5-4
5-4
5-4
5-5
5-5
5-10
Type B audio set (if equipped) .......................... 5-15
5-15
5-20
Audio control buttons ........................................ 5-25
Audio input terminal .......................................... 5-26
Precautions to observe when handling aRadio operation ...................................................... Built-in CD changer operation ...............................
compact disc ................................................... 5-27
MP3 audio ........................................................... 5-29
5-29
5-29
5-29
5-29
5-29
5-30
5-30What is MP3? .......................................................... Creating MP3 files ................................................... Saving MP3 files on a disc ..................................... Supported file systems .......................................... Compression format ............................................... Numbers of folders and files ................................. Copyright issues .....................................................
A3120BE-B.book 2 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-2
Antenna system
(cid:132) Printed antenna
Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.
Audio
any other material over the antenna portion of the rear window glass.
conditions,
(cid:132) FM reception Although FM is normally static free, recep- tion can be affected by the surrounding ar- ea, atmospheric station strength and transmitter distance. Build- ings or other obstructions may cause mo- mentary static, flutter or station interfer- ence. If reception continues to be unsatis- factory, switch to a stronger station. NOTE If a cell phone is placed near the radio, it may cause the radio to emit noise when it receives calls. This noise does not indicate a radio fault.
500200
The antenna is printed on the inner sur- face of the rear window glass. NOTE Antenna performance will deteriorate significantly if you apply tinting film or
XMTM Satellite radio recep- tion (if equipped)
XMTM is a continental U.S. based satellite radio service that offers more than 160
coast to coast channels, including music, news, sports, talk and children’s program- ming. XMTM provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XMTM service. For more in- formation, contact XMTM at www.xmradio.com or call 1-800-XM-RA- DIO (1-800-967-2346). The XMTM satellite radio receiver that is fitted to your vehicle receives the neces- sary signals from two specially designated satellites that are in a geostationary orbit over the equator. One satellite covers the east coast and the other covers the west coast. Both of them direct their signals north. These signals are then relayed throughout the USA by a network of ground repeater stations. The satellite ra- dio signals are transmitted as “line of sight” signals. Line of sight signals can be blocked by objects such as buildings, but the network of repeater stations allows signal coverage within urban areas such as cities. You may experience problems in receiv-A3120BE-B.book 3 ページ ２００６年５月３０日 火曜日 午前９時３２分
ing XMTM satellite radio signals in the fol- lowing situations. (cid:121) If you are driving northward in a coastal area You will notice that the XMTM satellite ra- dio antenna is fixed to the upper right hand corner of your windscreen.
5-3
500331
500332
500330
The signal comes from the south and may not be able to reach the antenna in some circumstances when you are driving north.
(cid:121) If you are driving in a tunnel or a cov- ered parking area (cid:121) If you are driving beneath the top level of a multi-level freeway (cid:121) If you drive under a bridge (cid:121) If you are driving next to a tall vehicle (such as a truck or a bus) that blocks the signal (cid:121) If you are driving in a valley where the surrounding hills or peaks block the signal from the south (cid:121) If you are driving on a mountain road where the southern direction is blocked by mountains
(cid:121) If you are driving in an area with tall trees that block the signal (10 m or more), for example on a road that goes through a dense forest (cid:121) The signal can become weak in some areas that are not covered by the repeater station network.
Please note that these may be other un- foreseen circumstances when there are problems with the reception of XMTM sat- ellite radio signals.
A3120BE-B.book 4 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-4
Installation of accessories
Audio set
(cid:132) Type B audio set
Always consult your SUBARU dealer be- fore installing a citizen band radio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrect- ly installed or if they are not suited for the vehicle.
Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating de- tails.
(cid:132) Type A audio set
500263
(cid:121) Radio operation: refer to page 5-15 (cid:121) Built-in CD changer operation: refer to page 5-20
500262
(cid:121) Radio operation: refer to page 5-5 (cid:121) CD (compact disc) player operation: re- fer to page 5-10
A3120BE-B.book 5 ページ ２００６年５月３０日 火曜日 午前９時３２分
Type A audio set (if equipped)
The audio set will operate only when the ignition switch is in the “ACC” or “ON” position.
(cid:132) Radio operation
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(10)
500264
5-5
1) SAT button 2) FM AM button 3) AUX RSE button 4) TUNE TRACK button 5) AUDIO button 6) Power switch, volume control dial 7) SEEK FLDR button 8) SCAN button 9) TONE BAL button 10) Preset button
(cid:84) Power switch and volume control The dial (6) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and balance adjustment. (cid:84) Tone and balance control The volume control dial (6) normally func- tions as a volume control. This dial be- comes a control for Bass, Midrange, Tre- ble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 sec- onds.
– CONTINUED –
A3120BE-B.book 6 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-6
(cid:86) To change tone and balance control
modes
Each brief press of the “TONE BAL” but- ton (9) changes control modes in the fol- lowing sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the vol- ume control.)
Volume
(VOLUME)
Bass (BASS)
Midrange (MIDDLE)
Balance
(BALANCE)
Fader
(FADER)
Treble
(TREBLE)
The “TONE BAL” button is used for select- ing the following control modes:
A3120BE-B.book 7 ページ ２００６年５月３０日 火曜日 午前９時３２分
Control mode (Range of levels)
Turn counterclockwise
Turn clockwise
500204
Bass control (–6 to +6)
For less bass sound
For more bass sound
Midrange control (–6 to +6)
For less midrange sound
For more midrange sound
Treble control (–6 to +6)
For less treble sound
For more treble sound
Fader control (R9 to F9)
To increase rear speaker volume and decrease front speaker vol-
ume
To increase front speaker volume and decrease rear speaker vol-
ume
Balance control (L9 to R9)
To increase left speaker volume and decrease right speaker vol-
ume
To increase right speaker volume
and decrease left speaker vol-
ume
Volume control (0 to 40)
For less volume
For more volume
5-7
(cid:84) FM/AM radio
(cid:86) FM/AM selection button Push the “FM AM” button (2) when the ra- dio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2 or AM reception. (cid:86) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
(cid:86) Manual tuning Press the “ ” side of the TUNE TRACK button (4) to increase the tuning frequency and press the “ ” side of the button to decrease it. Each time the button is pressed, the fre- quency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode. If you hold down the “ ” side of the but- ton, the tuning frequency will increase continuously, and if you hold down the “ ” side of the button, the tuning fre- quency will decrease continuously. Re- lease the button when your desired fre- quency is reached. NOTE While you are holding down either side of the TUNE TRACK button, the tuning frequency will not stop changing even
– CONTINUED –
A3120BE-B.book 8 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-8
” or “
if the frequency of a receivable station is reached. (cid:86) Seek tuning If you press the “ ” side of the SEEK FLDR button (7), the radio will auto- matically search for a receivable station and stop at the first one it finds. This func- tion may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the de- sired station.
(cid:86) Automatic tuning (SCAN) Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any dis- played frequency. Press the “ ” side of the SEEK FLDR (7) button again to cancel the scan mode and to stop on any displayed fre- quency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high fre- quencies only.
” or “
Automatic tuning may not function proper- ly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.
(cid:86) Selecting preset stations Presetting a station with a preset button (10) allows you to select that station in a single operation. Up to six, AM, FM1 and FM2 stations each may be preset. (cid:86) How to preset stations 1. Press the “FM AM” button (2) to select FM1, FM2, or AM reception. 2. Press the “SCAN” button (8) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons (10) for more than 1.5 seconds to store the fre- quency. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory. NOTE (cid:121) If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the pre- set buttons are cleared. If this occurs, it is necessary to reset the preset but- tons. (cid:121) If a cell phone is placed near the ra- dio, it may cause the radio to emit
noise when it receives calls. This noise does not indicate a radio fault. (cid:84) XM Satellite radio To receive satellite radio, it is necessary to install the Subaru genuine satellite receiv- er (option part) and to enter into a con- tract. For details, please contact your SUBARU dealer. (cid:86) XMTM satellite radio XMTM is a continental U.S. based satellite radio service that offers more than 160
coast to coast channels, including music, news, sports, talk and children’s program- ming. XMTM provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XMTM service. For more in- formation, contact XMTM at www.xmradio.com or call 1-800-XM-RA- DIO (1-800-967-2346). (cid:86) Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may ob- struct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result in signal loss in- clude driving near a wall, steep cliff, hill or driving on the lower level of a multi-tieredA3120BE-B.book 9 ページ ２００６年５月３０日 火曜日 午前９時３２分
road or inside of a parking garage. To help reduce this condition, satellite ra- dio providers have installed ground-based repeaters in heavily populated areas. However, you may still experience recep- tion problems in some areas. (cid:86) Band selection button Push the “SAT” button (1) when the radio is off to turn on the radio. Push the “SAT” button when the radio is on to select SAT1, SAT2 or SAT3 recep- tion. (cid:86) Channel selection Press “ ” of the TUNE TRACK button (4) to select the next channel and press “ ” of the button to select the previous channel. ” of the button to Keep pressing “ change to the next channel continuously and keep pressing “ ” of the button to change to the previous channel continu- ously. (cid:86) Category selection Press “ ” of the SEEK FLDR button (7) to display the current category. ” again to select the next cate- Press “ gory, and press “ ” again to select the previous category.
” or “
(cid:86) Channel scan Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the channels until a station is found. The radio will stop at the station for five seconds while displaying the channel number, after which scanning will continue until the entire channel has been scanned from the low end to the high end. Also during the category selection, chan- nel scan can be performed in that catego- ry. Press the “SCAN” button again to cancel the SCAN mode and to stop on any dis- played channel. (cid:86) Selecting preset channels Presetting a channel with a preset button (10) allows you to select that channel in a single operation. Up to six, SAT1, SAT2
and SAT3 channels each may be preset.(cid:86) How to preset channels 1. Press the “SAT” button (1) to select SAT1, SAT2 and SAT3 reception. 2. Press the “SCAN” button (8) or the TUNE TRACK button (4) to select the channel. 3. Press one of the preset buttons (10) for more than 1.5 seconds to store the chan- nel. If the button is pressed for less than
5-9
1.5 seconds, the preceding selection will remain in memory. NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all channels stored in the pre- set buttons are cleared. If this occurs, it is necessary to reset the preset but- tons.
(cid:86) Display selection Press the “AUDIO” (5) button while receiv- ing satellite radio to change the display as follows:
CHANNEL
CATEGORY
TITLE
NAME
(cid:84) Rear seat entertainment If your vehicle is equipped with a Rear Seat Entertainment System, you can en- joy audio outputs from the system through the vehicle’s speakers by pressing the “RSE AUX” button (3). Press the button again to return to the audio set sound.
– CONTINUED –
A3120BE-B.book 10 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-10
(cid:132) Compact disc player operation
(1)
(2)
(3)
(4)
(5) (6)
(7)
1) CD button 2) TUNE TRACK button 3) AUDIO button 4) SEEK FLDR button 5) RDM button 6) RPT button 7) SCAN button 8) Eject button
(cid:84) To playback a compact disc (cid:86) When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. NOTE (cid:121) DO NOT INSERT TWO DISCS INTO THE DISC INSERTION SLOT AT A TIME. (cid:121) Be sure to insert a disc with the label side up. If you insert the disc the label side down, “CHECK DISC” will appear on the display and the player will not play anything. (cid:121) After the last song finishes, the play- er will automatically return to track 1
(the first song on the disc). (cid:121) If you insert a disc that cannot be played by the player, “CHECK DISC”(8)
500266
A3120BE-B.book 11 ページ ２００６年５月３０日 火曜日 午前９時３２分
will appear on the display and the play- er will revert to the previously selected mode. (cid:121) The player is designed to be able to play music CD-Rs and music CD-RWs, but it may not be able to play certain ones. (cid:121) Single CDs (i.e., 8 cm/3 inch CDs) are not supported, and if inserted, they will be immediately ejected.
(cid:86) When CD is in the player When the “CD” button (1) is pressed, the player will start playback. NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc).
the
“POWER-VOL” button
(cid:84) To stop playback of a CD When is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again. (cid:84) To select a song from its beginning (cid:86) Forward direction Briefly press the “ ” side of the TUNE TRACK button (2) to skip to the beginning of the next track/file (track). Each time this side of the button is pressed, the indicated track/file (track) number will increase.
NOTE In an MP3 folder, skipping past the last track/file (track) will take you back to the first track/file (track) in the folder. (cid:86) Backward direction Briefly press the “ ” side of the TUNE TRACK button (2) to skip to the beginning of the current track/file (track). Each time this side of the button is pressed, the indi- cated track/file (track) number will de- crease. NOTE In an MP3 folder, skipping past the last track/file (track) will take you back to the first track/file (track) in the folder.
(cid:84) Fast-forwarding and fast-reversing (cid:86) Fast-forwarding Press the “ ” side of the TUNE TRACK button (2) continuously to fast-forward the track/file. Release the button to stop fast-forward- ing. NOTE If you fast-forward past the last track/ file (track) on the disc, the player will select the first track/file (track) on the disc and start playing it.
5-11
(cid:86) Fast-reversing Press the “ ” side of the TUNE TRACK button (2) continuously to fast-reverse the track/file (track). Release the button to stop fast-reversing. NOTE If you fast-reverse to the beginning of the first track/file (track) on the disc, the fast-reversing will stop and the player will start playing the first track/ file (track) on the disc.
(cid:84) Folder selection (MP3 disc) ” side of the SEEK FLDR Press the “ button (2) briefly to select the next folder. Pressing the “ ” side of the same button the first time makes the player go back to the beginning of the currently selected file; pressing it a second time makes it go back to the previously selected file. NOTE Only MP3 folders are recognized when an attempt to select the next or previ- ous folder is made. If no appropriate folder exists on the disc, pressing the “ ” side of the SEEK FLDR button has no effect.
” or “
– CONTINUED –
A3120BE-B.book 12 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-12
(cid:84) Repeating
(cid:86) To repeat the currently playing
track/file (track)
To repeat a track/file (track), briefly press the “RPT” button (6) while the track/file (track) is playing. The display will show “RPT”, and the track/file (track) will be re- peated. To cancel the track/file (track) repeat-play mode: Press the “RPT” button once (non-MP3
disc) Press the “RPT” button twice (MP3 disc) The “RPT” indication will go off, and the normal playback mode will be resumed. NOTE (cid:121) With an MP3 disc inserted, each time you briefly press the button, the mode will change to the next one in the fol- lowing sequence.RPT
D-RPT
CANCEL
If you accidentally press the button and cancel the track/file (track) repeat- play mode, press it again to reselect the repeat-play mode. (cid:121) The repeat-play mode will be can- celed if you perform any of the follow- ing steps:
” button
(cid:121) Press the “RDM” button (cid:121) Press the “SCAN” button (cid:121) Press the “ (cid:121) Select the radio mode (cid:121) Press the “RSE AUX” button (cid:121) Press the “ the SEEK FLDR button (MP3 disc) (cid:121) Turn off the power of the audio equipment. (cid:121) Turn the ignition switch to the “OFF” position.
” side of
” or “
(cid:86) To repeat the currently playing fold-
er (MP3 disc)
To repeat the currently playing folder, press the “RPT” (6) button twice while a file (track) is playing. The display will show “F-RPT”, and the folder will be played re- peatedly. To cancel the folder repeat-play mode, press the “RPT” button once more. The “F-RPT” indication will go off, and the nor- mal playback mode will be resumed. NOTE (cid:121) Each time you briefly press the but- ton, the mode will change to the next one in the following sequence.
RPT
F-RPT
CANCEL
the
If you accidentally press the button and cancel folder repeat-play mode, press it again to reselect the folder repeat-play mode. (cid:121) The folder repeat-play mode will be cancelled if you perform any of the fol- lowing steps:
” button
(cid:121) Press the “RDM” button (cid:121) Press the “SCAN” button (cid:121) Press the “ (cid:121) Select the radio mode (cid:121) Press the “RSE AUX” button (cid:121) Press the “ the SEEK FLDR button (MP3 disc) (cid:121) Turn off the power of the audio equipment. (cid:121) Turn the ignition switch to the “OFF” position.
” side of
” or “
(cid:84) Random playback
(cid:86) Non-MP3 disc Press the “RDM” button (5) briefly during disc playback to play all of the tracks on the disc in a random order. The display will show “RDM”, and all of the tracks on the disc will be played in a random order. To cancel random mode, press the button again. The “RDM” indication will go off, and the normal playback mode will be re- sumed.
A3120BE-B.book 13 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-13
” button
NOTE Random playback will be cancelled if you perform any of the following steps: (cid:121) Press the “RPT” button (cid:121) Press the “SCAN” button (cid:121) Press the “ (cid:121) Select the radio mode (cid:121) Press the “RSE AUX” button (cid:121) Press the “ SEEK FLDR button (cid:121) Turn off the power of the audio equipment. (cid:121) Turn the ignition switch to the “OFF” position.
” side of the
” or “
(cid:86) MP3 disc Press the “RDM” button (5) during disc playback to play all of the tracks in the folder currently being played in random or- der. Press the “RDM” button again to play all of the tracks on the disc in random or- der. The display will show “RDM” during the random mode. To cancel the random mode, press the “RDM” button during “in-disc” random playback. The “RDM” indication will go off, and the normal playback mode will be re- sumed. NOTE (cid:121) Each time you briefly press the but- ton, the mode will change to the next one in the following sequence.
CANCEL
If you accidentally press the button and cancel the random mode, press it again to reselect the random mode. (cid:121) Random playback will be cancelled if you perform any of the following steps:
” button
(cid:121) Press the “RPT” button (cid:121) Press the “SCAN” button (cid:121) Press the “ (cid:121) Select the radio mode (cid:121) Press the “RSE AUX” button (cid:121) Press the “ ” or “ the SEEK FLDR button (cid:121) Turn off the power of the audio equipment. (cid:121) Turn the ignition switch to the “OFF” position.
” side of
in succession. Press
(cid:84) Scan The scan mode lets you listen to the first 10 seconds of each track/file (track) on the disc/folder the “SCAN” button (7) to start scanning through all tracks upward beginning with the track/file (track) following the currently selected one. After all tracks/files (tracks) on the disc/folder has been scanned, nor- mal playback mode is restored.
” or “
” side of the
” side of the
To cancel a scan, press the button again. NOTE The scan mode will be cancelled if you perform any of the following opera- tions: (cid:121) Press the “RPT” button (cid:121) Press the “RDM” button ” button (cid:121) Press the “ (cid:121) Press the “ ” or “ TUNE TRACK button (cid:121) Press the “ SEEK FLDR button (MP3 disc) (cid:121) Select the radio mode (cid:121) Press the “RSE AUX” button (cid:121) Turn off the power of the audio equipment. (cid:121) Turn the ignition switch to the “OFF” position. (cid:84) To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject but- ton “ NOTE (cid:121) Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. (cid:121) If the disc is left ejected for more than approximately 15 seconds after the ignition switch is turned to the “OFF” position, a disc protection func-
” (8). The disc will be ejected.
– CONTINUED –
A3120BE-B.book 14 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-14
tion will operate, automatically reload- ing the disc. In this case, the disc is not played. (cid:84) Display selection (MP3 disc) If you press the “AUDIO” button (3) during playback, the indication will change to the next one in the following sequence.
File title
Time
Folder title
(cid:84) Page (track/folder title) scroll (MP3
disc)
If, having pressed the “AUDIO” button (3) to select track title or folder title display, you press the “AUDIO” button again for less than 0.5 second, the title will be scrolled so you can see all of it. You will see eight characters at a time. NOTE The display is designed to show titles for up to three pages (64 characters in total).
A3120BE-B.book 15 ページ ２００６年５月３０日 火曜日 午前９時３２分
Type B audio set (if equipped)
The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions.
(cid:132) Radio operation
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(10)
500265
5-15
1) SAT button 2) FM AM button 3) AUX RSE button 4) TUNE TRACK button 5) AUDIO button 6) Power switch, volume control dial 7) SEEK FLDR button 8) SCAN button 9) TONE BAL button 10) Preset button
(cid:84) Power switch and volume control The dial (6) is used for both power (ON/ OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial. The dial can also be used for tone and balance adjustment. (cid:84) Tone and balance control The volume control dial (6) normally func- tions as a volume control. This dial be- comes a control for Bass, Midrange, Tre- ble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after approximately 5 sec- onds.
– CONTINUED –
A3120BE-B.book 16 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-16
(cid:86) To change tone and balance control
modes
Each brief press of the “TONE BAL” but- ton (9) changes control modes in the fol- lowing sequence starting from volume control mode. (When the radio is first turned on, the control mode is in the vol- ume control.)
Volume
(VOLUME)
Bass (BASS)
Midrange (MIDDLE)
Balance
(BALANCE)
Fader
(FADER)
Treble
(TREBLE)
The “TONE BAL” button is used for select- ing the following control modes:
A3120BE-B.book 17 ページ ２００６年５月３０日 火曜日 午前９時３２分
Control mode (Range of levels)
Turn counterclockwise
Turn clockwise
500204
Bass control (–6 to +6)
For less bass sound
For more bass sound
Midrange control (–6 to +6)
For less midrange sound
For more midrange sound
Treble control (–6 to +6)
For less treble sound
For more treble sound
Fader control (R9 to F9)
To increase rear speaker volume and decrease front speaker vol-
ume
To increase front speaker volume and decrease rear speaker vol-
ume
Balance control (L9 to R9)
To increase left speaker volume and decrease right speaker vol-
ume
To increase right speaker volume
and decrease left speaker vol-
ume
Volume control (0 to 40)
For less volume
For more volume
5-17
(cid:84) FM/AM radio
(cid:86) FM/AM selection button Push the “FM AM” (2) button when the ra- dio is off to turn on the radio. Push the “FM AM” button when the radio is on to select FM1, FM2 or AM reception. (cid:86) Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.
(cid:86) Manual tuning Press the “ ” side of the TUNE TRACK button (4) to increase the tuning frequency and press the tuning button marked “ ” to decrease it. Each time the button is pressed, the fre- quency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode. If you hold down the “ ” side of the but- ton, the tuning frequency will increase continuously, and if you hold down the “ ” side of the button, the tuning fre- quency will decrease continuously. Re- lease the button when your desired fre- quency is reached. NOTE While you are holding down either side of the TUNE/TRACK button, the tuning frequency will not stop changing even
– CONTINUED –
A3120BE-B.book 18 ページ ２００６年５月３０日 火曜日 午前９時３２分
5-18
” or “
if the frequency of a receivable station is reached. (cid:86) Seek tuning (SEEK) If you press the “ ” side of the SEEK FLDR button (7), the radio will auto- matically search for a receivable station and stop at the first one it finds. This func- tion may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the de- sired station.
(cid:86) Scan tuning (SCAN) Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any dis- played frequency. Press the “ ” side of the SEEK FLDR button (7) again to cancel the scan mode and to stop on any displayed fre- quency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high fre- quencies only.
” or “
Automatic tuning may not function proper- ly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.
(cid:86) Selecting preset stations Presetting a station with a preset button allows you to select that station in a single operation. Up to six AM, FM1 and FM2
stations each may be preset. (cid:86) How to preset stations 1. Press the “FM AM” button (2) to select FM1, FM2 or AM reception. 2. Press the “SCAN” button (8) or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons for more than 1.5 seconds to store the fre- quency. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory. NOTE (cid:121) If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the pre- set buttons are cleared. If this occurs, it is necessary to reset the preset but- tons. (cid:121) If a cell phone is placed near the ra- dio, it may cause the radio to emitnoise when it receives calls. This noise does not indicate a radio fault. (cid:84) XM Satellite radio To receive satellite radio, it is necessary to install the Subaru genuine satellite receiv- er (option part) and to enter into a con- tract. For details, please contact your SUBARU dealer. (cid:86) XMTM satellite radio XMTM is a continental U.S. based satellite radio service that offers more than 160
coast to coast channels, including music, news, sports, talk and children’s program- ming. XMTM provides digital quality audio and text information, including song title and artist name. A service fee is required to receive the XMTM service. For more in- formation, contact XMTM at www.xmradio.com or call 1-800-XM-RA- DIO (1-800-967-2346). (cid:86) Satellite radio reception Satellite radio signals are best received in areas with a clear view of the open sky. In areas where there are tall buildings, trees, tunnels or other structures that may ob- struct the signal of the satellites, there may be signal interruptions. Other circum- stances that may result in signal loss in- clude driving near a wall, steep cliff, hill or driving on the lower level of a multi-tieredA3120BE-B.book 19 ページ ２００６年５月３０日 火曜日 午前９時３２分
road or inside of a parking garage. To help reduce this condition, satellite ra- dio providers have installed ground-based repeaters in heavily populated areas. However, you may still experience recep- tion problems in some areas. (cid:86) Band selection button Push the “SAT” button (1) when the radio is off to turn on the radio. Push the “SAT” button when the radio is on to select SAT1, SAT2 or SAT3 recep- tion. (cid:86) Channel selection Press “ ” of the TUNE TRACK button (4) to select the next channel and press “ ” of the button to select the previous channel. ” of the button to Keep pressing “ change to the next channel continuously and keep pressing “ ” of the button to change to the previous channel continu- ously. (cid:86) Category selection Press “ ” of the SEEK FLDR button (7) to display the current category. ” again to select the next cate- Press “ gory, and press “ ” again to select the previous category.
” or “
(cid:86) Channel scan Press the “SCAN” button (8) to change the radio to the SCAN mode. In this mode, the radio scans through the channels until a station is found. The radio will stop at the station for five seconds while displaying the channel number, after which scanning will continue until the entire channel has been scanned from the low end to the high end. Also during the category selection, chan- nel scan can be performed in that catego- ry. Press the “SCAN” button again to cancel the SCAN mode and to stop on any dis- played channel. (cid:86) Selecting preset channels Presetting a channel with a preset button
