2001 Subaru Legacy Owners Manual

Legacy U.S.A..(ENG.)A2280BE–A

Operating tips for heater and air conditioner

B Cleaning ventilator grille

Climate control

HB5019BC

Always keep the front ventilator inlet grille free of snow, leaves, or oth- er obstructions to ensure efficient heating and defrosting. Since the condenser is located in front of the radiator, this area should be kept clean because cooling performance is impaired by any accumulation of insects and leaves on the condenser.

B Efficient cooling after parking in direct sunlight After parking in direct sunlight, drive with the windows open for a few minutes to allow outside air to circulate into the heated interior. This results in quicker cooling by the air conditioner. Keep the windows closed during the operation of the air conditioner for maximum cool- ing efficiency.

B Lubrication oil circulation in the refrigerant circuit Operate the air conditioner compressor at a low engine speed (at idle or low driving speeds) a few minutes each month during the off-sea- son to circulate its oil.

B Checking air conditioning system before summer season Check the air conditioner unit for refrigerant leaks, hose conditions, and proper operation each spring. This check is best performed by your SUBARU dealer.

– CONTINUED –

4-19

Legacy U.S.A..(ENG.)A2280BE–A

B Cooling and dehumidifying in high humidity and low tempera-

ture weather condition

Under certain weather conditions (high relative humidity, low tempera- tures, etc.) a small amount of water vapor emission from the air outlets may be noticed. This condition is normal and does not indicate any problem with the air conditioning system.

B Air conditioner compressor shut-off when engine is heavily

loaded

To improve acceleration and gas mileage, the air conditioner com- pressor is designed to temporarily shut off during air conditioner op- eration whenever the accelerator is fully depressed such as during rapid accerelation or when driving on a steep upgrade.

B Refrigerant for your climate control system Your air conditioner uses ozone friendly refrigerant HFC134a. There- fore, the method of adding, changing or checking the refrigerant is different from the method for CFC12 (freon). Consult your SUBARU dealer for service. Repairs needed as a result of using the wrong refrigerant are not covered under warranty.

Air filtration system (if equipped)

If your vehicle’s air conditioning system is equipped with a optional air filtration system, replace the filter element according to the replacement schedule shown below. This schedule should be followed to maintain the filter’s dust collection ability. Under extremely dusty conditions, the filter should be replaced more frequently. Since the filter element is a viscous type, it is unnecessary to clean or wash the element. Have your filter checked or replaced by your SUBARU dealer.

Replacement schedule:

Every 12 months or 7,500 miles (12,000 km) whichever comes first

NOTE The filter can influence the air conditioning, heating and defroster performance.

4-20

Legacy U.S.A..(ENG.)A2280BE–A

Audio

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Antenna system Installation of accessories Audio set Type A and B audio set (if equipped) Type C audio set (if equipped) Type D audio set (if equipped) McIntosh audio set (if equipped) CD player 1 (if equipped) CD player 2 (if equipped) In-dash 6 CD auto changer (if equipped) Precautions to observe when handling

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . . . . . . . . . .

a compact disc (CD)

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5-2
5-3
5-3
5-7
5-19
5-33
5-39
5-52
5-54
5-57

5-60

Legacy U.S.A..(ENG.)A2280BE–A

Antenna system

B Printed antenna

CAUTION

Do not use sharp instruments or window cleaner containing abra- sives to clean the inner surface of the window on which the antenna is printed. Doing so may damage the antenna printed on the window.

The antenna is printed on the inside of the rear window glass (sedan) or the left side rear quarter window glass (station wagon).

HBF013IA

HB5038AA

B Pillar mounted antenna

Pull the antenna out to extend it to its full length.

OM-H2376

5-2

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B FM reception Although FM is normally static free, reception can be affected by the surrounding area, atmospheric conditions, station strength and trans- mitter distance. Buildings or other obstructions may cause momentary static, flutter or station interference. If reception continues to be unsat- isfactory, switch to a stronger station.

Installation of accessories

Always consult your SUBARU dealer before installing a citizen band ra- dio or other transmitting device in your vehicle. Such devices may cause the electronic control system to malfunction if they are incorrectly installed or if they are not suited for the vehicle.

Audio set

Your SUBARU may be equipped with one of the following audio sets. See the pages indicated in this section for operating details.

B Type A and type B audio set

D Radio operation: refer to page 5-7
D Cassette player operation: refer to page 5-11
D CD player control: refer to page 5-13
D CD changer control: refer to page 5-16

HB5041AA

– CONTINUED –

5-3

Legacy U.S.A..(ENG.)A2280BE–A

B Type C audio set

D Radio operation: refer to page 5-19
D Cassette player operation: refer to page 5-24
D CD (compact disc) player operation: refer to page 5-27
D CD changer control: refer to page 5-30

B Type D audio set

HB5042AA

HB5043AA

D Radio operation: refer to page 5-33
D Cassette player operation: refer to page 5-37
D CD player control: refer to page 5-38

5-4

Legacy U.S.A..(ENG.)A2280BE–A

B McIntosh audio set

Audio

D Radio operation: refer to page 5-39
D Cassette player operation: refer to page 5-44
D CD player operation: refer to page 5-46
D CD changer control: refer to page 5-49

B CD player 1 (Optional audio unit — if equipped)

HB5045AA

D Inserting and removing a disc: refer to page 5-52

HB5039AA

– CONTINUED –

5-5

Legacy U.S.A..(ENG.)A2280BE–A

B CD player 2 (Optional audio unit — if equipped)

D CD (compact disc) player operation: refer to page 5-54

B In-dash 6 CD auto changer (Optional audio unit — if equipped)

HB5044AA

D Inserting and removing a disc or all discs: refer to page 5-57

HB5040AA

5-6

Legacy U.S.A..(ENG.)A2280BE–A

Audio

Type A and B audio set (if equipped)

Type A: Without weather band Type B: With weather band

The audio set will operate only when the ignition switch is in the “ACC” or “ON” position.

Radio operation

HB5041BB

1 Power switch/Volume, Tone, Balance, Fader control dial

2 AUDIO button 3 BAND button

4 Tuning buttons 5 Preset buttons 6 SCAN button

B Power switch and volume/bass/treble/fader/balance control n Power switch and volume control (PWR/VOL) The dial 1 is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial.

– CONTINUED –

5-7

Legacy U.S.A..(ENG.)A2280BE–A

n Tone and balance control (AUDIO) The volume control dial 1 normally functions as a volume control. This dial becomes a control for Bass, Treble, Fader or Balance when you select the appropriate tone and balance control mode. Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5 seconds.

To change control modes: Each brief press of the “AUDIO” button 2 changes control modes in the following sequence starting from vol- ume control mode. (When the radio is first turned on, the control mode is in the volume control.) Volume

Balance

Treble

Fader

Bass

The “AUDIO” button 2 is used for selecting the following control modes:

Display

Control mode

Turn counterclockwise

Turn clockwise

HB5036BA

BAS

TRE

FAd

Bass control

For less bass

For more bass

Treble control

For less treble

For more treble

Fader control

To increase rear speaker volume and decrease front

To increase front speaker volume and decrease rear

speaker volume

speaker volume

BAL

Balance control

To increase left speaker

volume and decrease right

To increase right speaker volume and decrease left

speaker volume

speaker volume

VOL

Volume control

For less volume

For more volume

5-8

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B Waveband selection n FM/AM selection (P119 type audio set) Push the “BAND” button 3 to select FM1, FM2 or AM reception. The display indicates which one is currently selected.

n FM/AM/Weather band selection (P120 type audio set) Push the “BAND” button 3 to select FM1, FM2, AM or Weather band (WB) reception. The display indicates which is currently selected.

B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.

B Tuning (TUNE) n Manual tuning (TUNE) Press the tuning button 4 marked “Y” to increase the tuning frequen- cy and press the tuning button marked “B” to decrease it. Each time the button is pressed, the frequency interval can be changed between 10 kHz in the AM mode and 0.2 MHz in the FM mode. Constant pressure on the button causes a continuous change in the frequency.

n Manual tuning for weather band When weather band mode is selected, press the tuning button 4
marked “Y” to change the WB channel up and press the tuning but- ton marked “B” to change the WB channel down. Each time the but- ton is pressed, the WB channel changes to the next channel. Constant pressure on the button causes a continuous change in the frequency.

n Automatic tuning (SCAN) Press the “SCAN” button 6 to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while display- ing the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end.

– CONTINUED –

5-9

Legacy U.S.A..(ENG.)A2280BE–A

Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function properly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.

B Selecting preset stations Presetting a station with a “preset button” 5 allows you to select that station in a single operation. Up to six WB (if equipped), AM, FM1 and FM2 stations each may be preset.

B How to preset stations 1. Press the “BAND” button 3 to select FM1, FM2, AM or WB (if equipped) reception. 2. Press the “SCAN” button or tune the radio manually until the desired station frequency is displayed. 3. Press one of the preset buttons for more than 2 seconds to store the frequency. At this time, there will momentarily be no sound from the radio. If the button is pressed for less than 2 seconds, the preced- ing selection will remain in memory.

NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is neces- sary to reset the preset buttons.

5-10

Legacy U.S.A..(ENG.)A2280BE–A

Cassette player operation

Audio

HB5041CB

7 Cassette slot 8 Eject button 9 TAPE button Q TPS (Tape Program Search) W Repeat button

E Fast-forward button R Rewind button T Dolby B NR button Y Program button

NOTE D Only use good quality cassettes (cassettes longer than C-90 are not recommended). D Put cassettes back in their boxes immediately after use to protect them from dust and dirt and to prevent the tape from unwinding. D Never expose cassettes to heat, direct sunlight or moisture. D Clean the tape head (once or twice a month) using a wet-type cleaning cassette.

B Cassette slot Insert a cassette with the exposed tape side facing to the right. After insertion, playback starts.

B TAPE button Press the “TAPE button” 9 when the cassette left in the cassette slot is to be played back again.

– CONTINUED –

5-11

Legacy U.S.A..(ENG.)A2280BE–A

B Tape travel indicators These indicate the direction the cassette tape is moving. " : Indicates that the top side of the cassette is being played back. A : Indicates that the bottom side of the cassette is being played back.

B Program button (PROG) When the program button Y is pressed during playback, the tape travel indicators will switch and the player will begin playing back the opposite side of the tape. The same mechanism is automatically acti- vated when the end of the tape is reached. This allows the opposite side of the tape to play, providing continuous playback.

B Fast-forward button (FF) To fast-forward the tape, press the “FF” button E. To stop fast-for- warding, lightly press the “

” 8 button.

B Rewind button (REW) To rewind the tape, press the “REW” button R. To stop rewinding, lightly press the “

” 8 button.

” button 8 is pressed, playback stops and the cassette

B Eject button ( When “ tape is ejected. The ejection function is also active when the ignition switch is in the “LOCK” position. Always make certain that you remove the cassette tape.

B Repeat (RPT) Press the “RPT” button W while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.

5-12

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B Dolby B NR button ( Press the “ Dolby NR system*. The “ cy noise on the tape will be reduced for clearer sound reproduction.

” button T when playing tapes recorded using the ” indicator will light up and high-frequen-

*Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Licensing Corporation.

CD player control (If optional CD player is connected) An optional CD player can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “CD player 1” in this chapter.

U CD button I RAND (Random) button O RPT (Repeat) button

HB5041DB

P Track selection buttons A SCAN button

B To start playback n When CD is not in the CD player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) on the CD player and the player will automatically pull the disc into position.

– CONTINUED –

5-13

Legacy U.S.A..(ENG.)A2280BE–A

After insertion, the CD player mode indicator “CD” will come on and playback will start.

n When CD is in the CD player Press the “CD” button U. The “CD” indicator will come on, and the track number will appear on the display and the CD player will start playback.

NOTE D If the “CD” button is pressed during a radio broadcast, the disc will interrupt the broadcast. D After playback on the last song finishes, the player will auto- matically return to track 1 (the first song on the disc).

B To select a song from its beginning Briefly press the “""❚ ” button P to skip to the beginning of the next track and briefly press the “❚ AA” button to skip to the beginning of the current track.

B Fast-forwarding and fast-reverse Press the “""❚ ” button P continuously for more than a half second to fast-forward the disc. Press the “❚ AA” button continuously for more than a half second to fast reverse the disc. Release the button to stop fast forwarding or fast reverse.

B Repeat Press the “RPT” button O while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.

B Random playback Press the “RAND” button I while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored.

5-14

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B Scan (a convenient way to become familiar with a disc) 1. Press the “SCAN” button A.

– The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after playing all pro- grams. Then, normal playback starts.

2. Press the “SCAN” button again when you hear a track you like.

– Normal playback resumes.

B To stop playback To stop playback and switch over to the radio mode, press the “BAND” button. To stop playback and switch over to the cassette player mode, press the “TAPE” button.

– CONTINUED –

5-15

Legacy U.S.A..(ENG.)A2280BE–A

CD changer control (If optional in dash CD changer is connected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “In-dash 6 CD auto changer” in this chapter.

HB5041EB

S CD button D Disc up/down buttons F RAND (Random) button

G RPT (Repeat) button H Track selection buttons J SCAN button

B To start playback Press the “CD” button S. The “CD” indicator will come on and the disc number will appear on the display and the CD changer will start playback.

NOTE D If the “CD” button is pressed during a radio broadcast, the CD changer will interrupt the broadcast. D At the end of the disc, playback automatically continues with the next disc. D After playback on the last disc finishes, the player will auto- matically return to the first disc.

5-16

Legacy U.S.A..(ENG.)A2280BE–A

Audio

D If you have loaded fewer than 6 discs, any missing disc is automatically skipped.

B Selection of a desired disc Briefly press the “Y” button D to skip to the next disc and briefly press the “B” button to skip to the previous disc.

n Operation with the in-dash CD changer unit Press the desired “Disc select” button (numbered from 1 to 6) and the disc will begin to play.

B To select a song from its beginning Briefly press the “""❚ ” button H to skip to the beginning of the next track and briefly press the “❚ AA” button to skip to the beginning of the current track.

B Fast-forwarding and fast-reverse Press the “""❚ ” button H continuously for more than a half second to fast-forward the disc. Press the “❚ AA” button continuously for more than a half second to fast reverse the disc. Release the button to stop fast forwarding or fast reverse.

B Repeat Press the “RPT” button G while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.

B Random playback Press the “RAND” button F while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored.

– CONTINUED –

5-17

Legacy U.S.A..(ENG.)A2280BE–A

B Scan (a convenient way to become familiar with a disc) 1. Press the “SCAN” button J.

– The display shows “SCAN” and the track number being scanned. – You hear the first 10 seconds of each track. – The operation is automatically cleared after playing all pro- grams. Then, normal playback starts.

2. Press the “SCAN” button again when you hear a track you like.

– Normal playback resumes.

B To stop playback To stop playback and switch over to the radio mode, press the “BAND” button. To stop playback and switch over to the cassette player mode, press the “TAPE” button.

5-18

Legacy U.S.A..(ENG.)A2280BE–A

Type C audio set (if equipped)

The radio will operate only when the ignition switch is in the “ACC” or “ON” position.

Audio

Radio operation

1 FM/AM selection button 2 SCAN button 3 WB (weather band) button 4 Tuning buttons 5 Preset buttons

HB5042BB

6 Fader/Balance selection

button

7 Power switch, Volume control, Bass/Middle/Treble control and Fader/Balance control dial

8 AUDIO (audio mode) button

B Power switch and volume/bass/treble/fader/balance control

(PWR/VOL)

The dial 7 is used for both power (ON/OFF) and volume control. The radio is turned ON and OFF by pushing the dial and the volume is controlled by turning the dial.

– CONTINUED –

5-19

Legacy U.S.A..(ENG.)A2280BE–A

This dial is used for bass/middle/treble controls when the “AUDIO” button 8 is in the depressed position. It is also used for fader/balance controls when the “FAD/BAL” button 6 is in the depressed position.

Display

Control mode

HB5036BA

Turn counterclockwise

Turn clockwise

For less bass

For more bass

For less middle note

For more middle note

Bass control

Middle note control

Treble control

For less treble

For more treble

Fader control

To increase rear speaker volume and decrease front

To increase front speaker volume and decrease rear

speaker volume

speaker volume

BAS

MId

TRE

FAd

BAL

Balance control

To increase left speaker

volume and decrease right

To increase right speaker volume and decrease left

speaker volume

speaker volume

VOL

Volume control

For less volume

For more volume

n Tone control The volume control dial 7 normally function as volume control. The dial become a control for Bass, Middle note or Treble when you select the appropriate tone control mode. Choose desired level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5
seconds. To change control modes: Each brief press of the “AUDIO” button 8 changes control modes in the following sequence starting from bass control mode. (When the radio is first turned on, the control mode is in the volume control.)

5-20

Legacy U.S.A..(ENG.)A2280BE–A

Bass Middle Treble Volume (BAS) (MId) (TRE) (VOL)

Audio

n Fader and balance control The volume control dial 7 normally function as volume control. The dial become the controls for Fader or Balance when you select the appropriate fader and balance control mode. Choose desired setting for each mode by turning the volume control dial. The control function returns to volume control mode after about 5
seconds.

To change control modes: Each brief press of the “FAD/BAL” button 6 changes control modes in the following sequence starting from fader control mode. (When the radio is turned on, the control mode is in the volume control.)

Fader Balance Volume (FAd) (BAL) (VOL)

n Display illumination dimness cancellation The brightness of the radio display dims when the light switch is in the “p” or “w” positions. If this makes the display difficult to read, press the volume dial for more than two seconds to return the display to original brightness.

B FM/AM selection button (FM/AM) Push the “FM/AM” button 1 when the radio is off to turn on the radio. Push the “FM/AM” button when the radio is on to select FM1, FM2 or AM reception. Each time this button is pressed, the band will change in the following order:

FM1

FM2

AM

The display indicates which one is currently selected.

– CONTINUED –

5-21

Legacy U.S.A..(ENG.)A2280BE–A

B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.

B Weather band button (WB) Push the “WB” button 3 when the radio is off to turn on the radio in the weather band. Press the “WB” button when the radio is on to select the weather band.

B Manual tuning (TUNE) n Manual tuning for AM and FM waveband Push the tuning button 4 marked “Y” to increase the tuning frequen- cy and press the tuning button marked “B” to decrease it. Each time the button is pressed, the frequency changes 10 KHz in the AM waveband and 0.2 MHz in the FM waveband. Constant pressure on the button causes a continuous change in the frequency.

n Manual tuning for weather band When weather band mode is selected, press the tuning button 4
marked “Y” to change the WB channel up and press the tuning but- ton marked “B” to change the WB channel down. Each time the but- ton is pressed, the WB channel changes to the next channel. Constant pressure on the button causes a continuous change in the channel.

B Automatic tuning (SCAN) Press the “SCAN” button 2 to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while display- ing the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only.

5-22

Legacy U.S.A..(ENG.)A2280BE–A

Audio

Automatic tuning may not function properly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.

B Selecting preset stations Presetting a station with a preset button 5 allows you to select that station in a single operation. Up to six AM, FM1, FM2 and WB stations each may be preset.

B How to preset stations 1. Press the “FM/AM” selection button to select AM, FM1 or FM2 re- ception.

Press the “WB” button 3 to select the weather band.

OR

2. Press the “SCAN” button 2 or tune the radio manually until the de- sired station frequency is displayed. 3. Press one of the preset buttons 5 for at least 1.5 seconds to store the frequency. The frequency of the station will flash once on the dis- play at this time. If the button is pressed for less than 1.5 seconds, the preceding selection will remain in memory.

NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is neces- sary to reset the preset buttons.

– CONTINUED –

5-23

Legacy U.S.A..(ENG.)A2280BE–A

Cassette player operation

9 TAPE (cassette player

selection) button

Q Cassette slot W Eject button E TPS button

HB5042CB

R Repeat button T Fast forward button Y Rewind button U Dolby B NR button I Program switching button

NOTE D Only use good quality cassettes (cassettes longer than C-90 are not recommended). D Put cassettes back in their boxes immediately after use to protect them from dust and dirt and to prevent the tape from unwinding. D Never expose cassettes to heat, direct sunlight or moisture. D Clean the tape head (once or twice a month) using a wet-type cleaning cassette.

B To play back a cassette tape n When cassette tape is not in the player When a cassette is partially inserted, it is automatically drawn in and starts tape playback.

5-24

Legacy U.S.A..(ENG.)A2280BE–A

Audio

n When cassette tape is in the player When the “TAPE” button 9 is pressed, the display will show “PLAY” and the player will start playback.

B Tape travel indicators These indicate the direction the cassette tape is moving. " : indicates that the top side of the cassette is being played back. A : indicates that the bottom side of the cassette is being played back. B Program switching button (PROG) When the program switching button “PROG” I is pressed during playback, the tape travel indicators will switch and the player will be- gin playing back the opposite side of the tape. The same mechanism is automatically activated when the end of the tape is reached. This allows the opposite side of the tape to play, providing continuous playback.

B Fast-forward button (FF) To fast-forward the tape, press the “FF” button T. The display will show “FF”. To stop fast-forwarding, press the “FF” or “TAPE” 9 button.

B Rewind button (REW) To rewind the tape, press the “REW” button Y. The display will indi- cate “REW”. To stop rewinding, press the “REW” or “TAPE” 9 button.

” button W is pressed, play back stops and the cassette

B Eject button ( When “ tape is ejected. The ejection function also operates when the ignition switch is in the “LOCK” position. Always make certain that you remove the cassette tape. B Tape program sensor button (TPS) n Blank skip When the “TPS” button E is pressed, the “TPS” indicator will come on and the player will automatically skip any blank portion of 15 second or more and play the next program, even if it is on the other side. To cancel blank skip mode, press the “TPS” button again.

– CONTINUED –

5-25

Legacy U.S.A..(ENG.)A2280BE–A

n Blank search Press “TPS” button E during playback to return to the beginning of the current selection or to skip to the beginning of the next selection. To use this function, press the “TPS” button to turn on the “TPS” indi- cator. If the fast-forward button “FF” T is then pressed, the player ad- vances the tape to the beginning of the next selection and starts play- ing it. If the rewind button “REW” Y is pressed instead, the player rewinds the tape to the beginning of the current selection and starts replaying it. The “TPS” function may not operate properly under the following conditions: D When the recording level is low. D When there are long pauses in the middle of a selection. D When the tape contains verbal material such as conversations. D When the blanks between selections are shorter than five seconds. D When there are no blanks between selections (live concerts, etc.).

B Repeat button (RPT) Push the “RPT” button R to repeat the piece of music being listened to. To use this function, push the “RPT” button while the piece you want to hear again is being played. “RPT” will be indicated on the dis- play. When the selection ends, the cassette player automatically re- winds to the beginning of the piece and the selection begins again. To cancel the repeat function, push the “RPT” button again. Until the repeat function is cancelled, the same piece of music will be repeated indefinitely. The “RPT” function may not operate properly under the following conditions: D When the recording level is low. D When there are long pauses in the middle of a selection. D When the tape contains verbal material such as conversations. D When the blanks between selections are shorter than five seconds. D When there are no blanks between selections (live concerts, etc).

B Dolby B NR button ( Press “ NR system*. The “ noise on the tape will be reduced for clearer sound reproduction.

” button U when playing tapes recorded using the Dolby ” indicator will light up and high-frequency

5-26

Legacy U.S.A..(ENG.)A2280BE–A

Audio

* Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Licensing Corporation.

B Auto metal sensor The cassette player automatically adjusts for metal or CrO2 tape.

Compact disc player operation

O SCAN button P Disc slot A Eject button S Random button

HB5042DB

D Repeat button F Track selection buttons G CD (CD player selection)

button

B To play back a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. A single CD (8 cm/3 inch CD) may also be used without any adapter.

– CONTINUED –

5-27

Legacy U.S.A..(ENG.)A2280BE–A

After insertion, the DISC indicator “ appear on the display and the player will start playback.

” will come on and “CD” will

NOTE D Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. D After the last song finishes, the player will automatically return to track 1 (the first song on the disc).

n When CD is in the player Press the “CD” button G. The display will show “CD” and the player will start playback.

NOTE After the last song finishes, playback will automatically return to track 1 (the first song on the disc).

B To select a song from its beginning n Forward direction Briefly press the “""❚ ” button F to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase. n Backward direction Briefly press the “❚ AA” button F to skip to the beginning of the cur- rent track. Each time the button is pressed, the indicated truck num- ber will decrease.

B Fast forwarding and fast reverse n Fast forwarding Press the “""❚ ” button F continuously for more than 0.5 second to fast forward the disc. Release the button to stop fast forwarding. n Fast reverse Press the “❚ AA” button F continuously for more than 0.5 second to fast reverse the disc. Release the button to stop fast reverse.

5-28

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B Repeat playback Press the “RPT” button D while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.

B Random playback Press the “RAND” button S while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored.

B Scan When the “SCAN” button O is pressed while the disc is being played back, you can hear the first 10 seconds of each track to seach for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc have been scanned, normal playback mode is restored.

B To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position.

” A. The disc will be ejected.

NOTE Avoid driving the vehicle with a CD sticking out, because vibra- tion might make it fall out.

– CONTINUED –

5-29

Legacy U.S.A..(ENG.)A2280BE–A

CD changer control (If optional in-dash CD changer is connected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information. For procedures for loading and un- loading CDs, refer to “In-dash 6 CD auto changer” in this chapter.

HB5042EB

H SCAN button J Disc up/down button K Random button

L Repeat button Z Track selection buttons X CD button

B To start playback When the “CD” button X is pressed, the CD changer will start play- back. The display shows the current disc number, track number and the elapsed time during playback.

5-30

Legacy U.S.A..(ENG.)A2280BE–A

Audio

NOTE D If a disc is in the player, the “CD” button is used to change from CD player operation to CD changer operation. Each time the “CD” button is pressed, the operating mode will change alter- nately. D At the end of the disc, the player automatically continues with the next disc. D After playback on the last disc finishes, playback will automat- ically return to the first disc. D If you have loaded fewer than 6 discs, any missing disc is automatically skipped.

B Selection of a desired disc Briefly press the “Y” button D to skip to the next disc and briefly press the “B” button to skip to the previous disc.

n Operation with the in-dash CD changer unit Press the desired “Disc select” button (numbered from 1 to 6) and the disc will begin to play.

B To select the desired disc Press either the disc up button “DISC Y” J or disc down button “DISC B” to select the desired disc. Each time the “DISC Y” J but- ton is pressed, the indicated disc number will increase. Each time the “DISC B” button is pressed, the indicated disc number will decrease. Constant pressure on these buttons causes a continuous change in the disc number.

B To select a song from its beginning n Forward direction Briefly press the “""❚ ” button Z to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase.

n Backward direction Briefly press the “❚ AA” button Z to skip to the beginning of the cur- rent track. Each time the button is pressed, the indicated track num- ber will decrease.

– CONTINUED –

5-31

Legacy U.S.A..(ENG.)A2280BE–A

B Fast forwarding and fast reverse n Fast forwarding Press the “""❚ ” button Z continuously for more than 0.5 second to fast forward the disc. Release the button to stop fast forwarding. If you continue fast forwarding to the end of the disc, the CD changer will automatically stop fast forwarding and start playback beginning with the first track on the current disc.

n Fast reverse Press the “❚ AA” button Z continuously for more than 0.5 second to fast reverse the disc. Release the button to stop fast reverse. If you continue fast reverse to the beginning of the disc, the CD changer will automatically stop fast reverse and start playback begin- ning with the first track on the current disc.

B Repeat playback Press the “RPT” button L while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.

B Random playback Press the “RAND” button K while a disc is being played back to play all songs on the disc in a random order. The “RAND” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RAND” indicator goes out, and normal playback mode is restored.

B Scan When the “SCAN” button H is pressed while the disc is being played back, you can hear the first 10 seconds of each track to search for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc have been scanned, normal playback mode is restored.

5-32

Legacy U.S.A..(ENG.)A2280BE–A

Type D audio set (if equipped)

The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions.

Audio

Radio operation

1 Tuning buttons 2 SCAN button 3 FM/AM selection button 4 Preset buttons

HB5043BB

5 AUDIO button 6 Power switch and volume

control

B Power switch and volume/bass/treble/fader/balance control n Power switch and volume control (PWR/VOL) The dial 6 is used for both power (on/off) and volume control. The radio is turned on and off by pushing the dial and the volume is con- trolled by turning the dial.

B Tone and balance control The volume control dial 6 normally functions as a volume control. This dial becomes a control for Bass, Treble, Fader or Balance when you select the appropriate tone and balance control mode.

– CONTINUED –

5-33

Legacy U.S.A..(ENG.)A2280BE–A

Choose desired volume level for each mode by turning the volume control dial. The control function returns to volume control mode after about 5 seconds.

To change control modes: Each brief press of the “AUDIO” button 5 changes control modes in the following sequence starting from vol- ume control mode. (When the radio is first turned on, the control mode is in the volume control.)

Volume (VOL)

Bass (BAS)

Treble (TRE)

Fader (FAD)

Balance (BAL)

The “AUDIO” button 5 is used for selecting the following control modes:

Display

Control mode

HB5036BA

BAS

TRE

FAD

Turn counterclockwise

Turn clockwise

Bass control

For less bass

For more bass

Treble control

For less treble

For more treble

Fader control

To increase rear speaker volume and decrease front

To increase front speaker volume and decrease rear

speaker volume

speaker volume

BAL

Balance control

To increase left speaker

volume and decrease right

To increase right speaker volume and decrease left

speaker volume

speaker volume

VOL

Volume control

For less volume

For more volume

5-34

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B FM/AM selection button (FM/AM) Push the “FM/AM” button 3 when the radio is on to select FM1, FM2
or AM reception. Each time this button is pressed, the band will change in the following order:

FM1

FM2

AM

The display indicates which one is currently selected.

B Stereo indicator The stereo indicator “ST” will come on when an FM stereo broadcast is received.

B Manual tuning (TUNING) Press the tuning button 1 marked “∧” to increase the tuning frequen- cy and press the tuning button marked “∨” to decrease it. Each time the button is pressed, the frequency changes 10 kHz in the AM mode and 0.2 MHz in the FM mode. Constant pressure on the button causes a continuous change in the frequency.

B Automatic tuning (SCAN) Press the “SCAN” button 2 to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while display- ing the frequency, after which scanning will continue until the entire band has been scanned from the low end to the high end. Press the “SCAN” button again to cancel the SCAN mode and to stop on any displayed frequency. When the “SCAN” button is pressed for automatic tuning, stations are scanned in the direction of low frequencies to high frequencies only. Automatic tuning may not function properly if the station reception is weakened by distance from the station or proximity to tall buildings and hills.

– CONTINUED –

5-35

Legacy U.S.A..(ENG.)A2280BE–A

B Selecting preset stations Presetting a station with a preset button 4 allows you to select that station in a single operation. Up to six AM, FM1 and FM2 stations each may be preset.

B How to preset stations 1. Press the “FM/AM” selection button 3 to select FM1, FM2 or AM reception. 2. Press the “SCAN” button 2 or tune the radio manually until the de- sired station frequency is displayed. 3. Press one of the preset buttons 4 for at least two seconds to store the frequency. The frequency of the station will flash once on the display at this time. If the button is pressed for less than two seconds, the preceding selection will remain in memory.

NOTE If the connection between the radio and battery is broken for any reason such as vehicle maintenance or radio removal, all stations stored in the preset buttons are cleared. If this occurs, it is neces- sary to reset the preset buttons.

5-36

Legacy U.S.A..(ENG.)A2280BE–A

Cassette player operation

Audio

HB5043CB

7 Eject button 8 Cassette slot

9 Fast-forward/Rewind button (Program switching buttons)

Q Dolby B NR button

NOTE D Only use good quality cassettes (cassettes longer than C-90 are not recommended). D Put cassettes back in their boxes immediately after use to protect them from dust and dirt and to prevent the tape from unwinding. D Never expose cassettes to heat, direct sunlight or moisture. D Clean the tape head (once or twice a month) using a wet-type cleaning cassette.

B Cassette slot Insert a cassette with the exposed tape side facing to the right. After inserting, playback starts.

B Tape travel indicators The tape travel indicators indicate the direction the cassette tape is moving. " : Indicates that the top side of the cassette is being played back. A : Indicates that the bottom side of the cassette is being played back.

– CONTINUED –

5-37

Legacy U.S.A..(ENG.)A2280BE–A

B Program switching buttons When the program switching buttons “ ” 9, are pressed at the same time during playback, the tape travel indicators will switch and the player will begin playing back the opposite side of the tape. The same mechanism is automatically activated when the end of the tape is reached. This allows the opposite side of the tape to play, providing continuous playback.

” and “

B Fast-forward button To fast-forward the tape, press the “ ” button 9 in the same direction as the tape travel indicator. To stop fast-forwarding, lightly press the opposite side of the “

” button.

” or “

” or “

B Rewind button ” button 9 in the direc- To rewind the tape, press the “ tion opposite to the tape travel indicator. To stop rewinding, lightly press the opposite side of the “

” button.

” or “

” or “

” button 7 is pressed, playback stops and the cassette

B Eject button ( When the “ tape is ejected. Before the ignition switch is turned to the “OFF” position, eject the tape from the player. Always make certain that you remove the cas- sette tape.

B Dolby BNR button (BNR) Press “BNR” button Q when playing tapes recorded using the Dolby NR system*. The “BNR” indicator will light up and high-frequency noise on the tape will be reduced for clearer sound reproduction.

* Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and the double-D Symbol are trade marks of Dolby Laboratories Licensing Corporation.

CD player operation (if optional CD player is connected) An optional CD player can be connected to this audio unit. See your SUBARU dealer for more information. For CD player operation proce- dures, refer to “CD player 2” in this chapter.

5-38

Legacy U.S.A..(ENG.)A2280BE–A

Audio

McIntosh audio set (if equipped)

The audio set will operate only when the ignition switch is in the “ACC” or “ON” positions.

CAUTION

The power amplifier for this audio set is mounted under the front passenger’s seat. The amplifier will become hot if the audio con- tinues to operate. Never touch the amplifier. Doing so could cause burns.

Radio operation

1 POWER ON/OFF button 2 FM/AM selection button 3 Tuning/FF⋅FB dial 4 Weather band button 5 Preset buttons

HB5045BB

6 Treble sound control knob 7 Volume and fader/balance

control dial

8 Bass sound control knob

– CONTINUED –

5-39

Legacy U.S.A..(ENG.)A2280BE–A

B ON-OFF switch The audio system can be turned on by pressing the POWER button when the ignition key is in the ACC or ON position. Pressing the POWER button once again will turn off the power. In addition, the fol- lowing six operations will also result in the audio system’s power be- ing turned on: D Pressing the FM/AM selector button D Pressing the Tape Mode selector button D Pressing the Disc Mode selector button (provided that a CD has been inserted or that a CD multi-changer is connected to the system) D Inserting a cassette D Inserting a CD D Pressing the Traffic information button

B Volume control

HBS040BB

Turn clockwise to increase the audio-system volume. Turn counterclockwise to reduce the audio-system volume.

B Tone control Bass and treble control is operated using the same knob. Use that knob for the separate adjustment of low pitch and high pitch sounds.

5-40

Legacy U.S.A..(ENG.)A2280BE–A

Audio

HBS041AA

n BASS control The bass control adjusts the level of low pitch sounds. The bass is adjusted by turning the knob from left to right in this condition. Turn clockwise to increase the level of bass tones. Turn counterclockwise to reduce the level of bass tones.

n TREBLE control The treble control adjusts the level of high pitch sounds. The treble is adjusted by turning the knob from left to right in this condition. Turn clockwise to increase the level of treble tones. Turn counterclockwise to reduce the level of treble tones.

B Balance control

HBS042BC

– CONTINUED –

5-41

Legacy U.S.A..(ENG.)A2280BE–A

n FADER control The balance control adjusts the balance between the front and rear speakers. The balance is adjusted by turning the knob from left to right in this condition. Turn clockwise to increase the relative sound volume in the front of the vehicle. Turn counterclockwise to increase the relative sound volume in the rear of the vehicle.

n BALANCE control The balance control adjusts the balance between the left and right speakers. Pull the knob out until it stops. The balance is adjusted by turning the knob from left to right in this condition. Turn clockwise to make the sound louder on the right of the vehicle. Turn counterclockwise to make the sound louder on the left of the ve- hicle.

B FM/AM selection button Press the FM/AM selector button to choose either FM or AM broad- casts. The display will show FM or AM accordingly. Use the tuning dial to select the station to which you wish to listen.

B Manual tuning Turn the tuning dial’s outer tuner to increase or decrease the reception frequency in individual steps.

FM band: 0.2 MHz steps AM band: 10 kHz steps

B Seek tuning (SEEK) If the Tuning dial’s outer tuner is turned for longer than half of a se- cond, the radio will begin to automatically search for receivable fre- quencies and will stop at the first one found. This function may not be available, however, when radio signals are weak. In such a situation, perform manual tuning to select the desired station.

5-42

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B Scan tuning (SCAN) Turn the tuning dial inner tuner to change the radio to the SCAN mode. In this mode, the radio scans through the radio band until a station is found. The radio will stop at the station for five seconds while displaying the frequency, after which scanning will continue until the entire band has been scanned. Turn the tuning dial’s inner tuner again to cancel the SCAN mode and to stop on any displayed frequency. Scan tuning may not function properly if the station reception is weak- ened by distance from the station or proximity to tall buildings and hills.

B Preset tuning Press any one of the preset buttons to select the corresponding, pre- viously-registered radio station. The LED at the top of that button will turn on.

n Manual preset D Use the tuning dial to select the radio station which you wish to register. D Choose the preset button to which you wish to assign that station and press it continuously for a period of more than 2 seconds. When the radio station has been successfully registered, the display will flash the corresponding radio frequency on and off once.

NOTE D Each preset button can be used to store both an FM station and an AM station. D If the power supply is interrupted by disconnection of the bat- tery, memory presets will be cleared and will be required to be re- input.

B Weather band button (WB) Push the “WB” button when the radio is off to turn on the radio in the weather band. Press the “WB” button when the radio is on to select the weather band.

– CONTINUED –

5-43

Legacy U.S.A..(ENG.)A2280BE–A

Cassette player operation

9 Cassette slot Q Eject button W TAPE (cassette player

selection) button

E Repeat button

HB5045CB

R Fast forward button T Play button Y Rewind button U Program switching button I Dolby B NR button

If a cassette is inserted into the cassette slot while the ignition switch is in the ACC or the ON position, that tape will start to play automatically. Press the TAPE button when you want to play a cassette that has pre- viously been inserted.

” button is pressed, playback stops and the cassette tape

B Cassette tape stop and eject button When “ is ejected. Before the ignition switch is turned to the “OFF” position, eject the tape from the player. Always make certain that you remove the cas- sette tape.

5-44

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B Program button (PROG) If a cassette is currently being played, the PROG button can be pressed to switch from the A-side to the B-side or vice-versa.

B Fast-forward button (FF) To fast-forward the tape, press the “FF” button. To stop fast-forward- ing, lightly press the “PLAY” button. If the “FF” button is pressed twice successively during playback, the player will fast-forward the tape to the end of the current song and resume the playback from the beginning of the next song.

B Rewind button (REW) To rewind the tape, press the “REW” button. To stop rewinding, lightly press the “PLAY” button. If the “REW” button is pressed twice successively during playback, the player will rewind the tape up to the beginning of the current song and resume the playback from its beginning.

B Repeat button (RPT) If the RPT button is pressed while a song on a cassette tape is being played, the cassette player will then begin to play that song repeated- ly. Press the RPT button once again to return to normal playback.

B Dolby B NR button (B NR) Press “B NR” button when playing tapes recorded using the Dolby NR system*. High-frequency noise on the tape will be reduced for clearer sound reproduction.

*Noise reduction system manufactured under license from Dolby Laboratories Licensing Corporation. “Dolby” and double-D Symbol are trade marks of Dolby Laboratories Licensing Corporation.

– CONTINUED –

5-45

Legacy U.S.A..(ENG.)A2280BE–A

Compact disc player operation

O DISC IN indicator light P Disc slot A Disc button

S Eject button D FF·FB dial F Repeat button

HB5045DB

B To play back a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. Single CDs (8 cm/3 inch CD) may also be used without an adapter. After inserting, the DISC IN indicator (LED) will come on and playback start.

NOTE D Make sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off.

5-46

Legacy U.S.A..(ENG.)A2280BE–A

Audio

D If a disc is inserted during a radio broadcast, the disc will interrupt the broadcast. D After the last song finishes, the disc will automatically return to track 1 (the first song on the disc) and will automatically play back.

n When CD is in the player When the “DISC” button is pressed, the player will start playback.

B To select a song from its beginning

HBS044CA

n Forward direction Turn the “FF⋅FB” dial clockwise and release it immediately to skip to the beginning of the next track. Each time the knob is turned and released, the indicated track number will increase.

n Backward direction Turn the “FF⋅FB” dial counterclockwise and release it immediately to skip to the beginning of the current track. If you continue to turn and release the knob, the indicated a number will decrease.

– CONTINUED –

5-47

Legacy U.S.A..(ENG.)A2280BE–A

B Fast forwarding and fast reverse

HBS044BA

n Fast forward Turn the “FF⋅FB” dial clockwise and hold it continuously for more than 2 seconds to fast forward the disc. Release the knob to stop fast forwarding.

n Fast reverse Turn the “FF⋅FB” dial counterclockwise and hold it continuously for more than 2 seconds to fast reverse the disc. Release the knob to stop fast reverse.

B Repeat Press the “A.S/RPT” button while a song is playing to play the song repeatedly. The “RPT” indicator will come on and the song will be played continuously. To cancel the repeat mode, press the button again. Then the “RPT” indicator goes out, and normal playback mode is restored.

B To stop playback Press the power switch to stop playback.

B To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position.

”. The disc will be ejected.

5-48

Legacy U.S.A..(ENG.)A2280BE–A

Audio

NOTE Avoid driving the vehicle with a CD sticking out, because vibra- tion might make it fall out.

CD changer control (If optional CD changer is con- nected) An optional CD changer can be connected to this audio unit. See your SUBARU dealer for more information.

G Disc button H FF·FB dial J Repeat button

HB5045EB

K Disc select button

(Disc 1 to 6)

B To start playback When the “DISC” button is pressed, the CD changer will start play- back.

NOTE D If the “DISC” button is pressed during a radio broadcast, the

– CONTINUED –

5-49

Legacy U.S.A..(ENG.)A2280BE–A

CD changer will interrupt the broadcast. D At the end of the disc, playback automatically continues with the next disc. D After playback on the last disc finishes, the disc will automati- cally return to the first disc (or first disc of the first magazine) and will automatically play back. D If you have loaded fewer than 6 discs, any missing disc is automatically skipped.

B Selection of a desired disc You can select a desired disc from among the discs contained in the magazines only by pressing the corresponding number one of the disc select buttons. If you are to listen to the 7th disc in the double magazine (12 discs), for example, it is selected first by selecting “M2” (“M2” means 2nd magazine) with the “DISC” button and then press- ing the “1” button of the disc select buttons. All other discs in the magazines can also be selected in a similar way.

NOTE D No disc change takes place if the button corresponding to the magazine slot in which no disc is loaded is pressed. D If the direct disc button corresponding to the disc now in play- back is pressed again, the disc will be replayed from its begin- ning.

B To select a song from its beginning

HBS044CA

5-50

Legacy U.S.A..(ENG.)A2280BE–A

Audio

n Forward direction Turn the “FF⋅FB” dial clockwise and release it immediately to skip to the beginning of the next track. Each time the knob is turned and released, the indicated track number will increase.

n Backward direction Turn the “FF⋅FB” dial counterclockwise and release it immediately to skip to the beginning of the current track. If you continue to turn and release the knob, the indicated truck number will decrease.

B Fast forwarding and fast reverse

HBS044BA

n Fast forward Turn the “FF⋅FB” dial clockwise and hold it continuously for more than 2 seconds to fast forward the disc. Release the knob to stop fast forwarding.

n Fast reverse Turn the “FF⋅FB” dial counterclockwise and hold it continuously for more than 2 seconds to fast reverse the disc.

B Repeat Press the “RPT” button briefly while a song is playing to play the song repeatedly. To cancel the repeat mode, press the button again.

B To stop playback Press the power switch to stop playback.

– CONTINUED –

5-51

Legacy U.S.A..(ENG.)A2280BE–A

CD player 1 (if equipped)

1 Disc slot 2 Disc indicator

3 Eject button

HB5039BB

CAUTION

D Use only music CDs identified by D Do not use CDs listed below which could cause damage to the CD player.

mark.

D Any disc with a peel-off or seal on it. D Any disc with scratches and/or dust. D Bent disc. D Cleaning disc. D CD accessory. (E.g., 3-inch (8 cm) disc adapter)

D Do not insert or remove any disc when the automatic transmis- sion selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).

5-52

Legacy U.S.A..(ENG.)A2280BE–A

Audio

B To insert a disc Be sure to hold a disc with the label side (the side where titles are printed) up. Push the disc into the slot. The disc will be automatically set in position by the auto-loading mechanism and begin playing. The disc indicator will turn on as the CD begins playing.

n Disc indicator Lit: A disc is in the slot (When the ignition switch is in the “ON” or “ACC” position). OFF: No disc is loaded or the ignition switch is in the “Lock” position.

B To remove disc left in slot Simply press the “Eject button” 3 and the disc will be ejected. This procedures is effective even when the ignition switch is in the “LOCK” position.

n Function control Refer to CD player control operating instructions described in the “Type A and B audio sets” section.

– CONTINUED –

5-53

Legacy U.S.A..(ENG.)A2280BE–A

CD player 2 (if equipped)

Compact disc player operation

1 Eject button 2 Repeat/random button 3 Scan/top button 4 Disc slot

HB5044BB

5 Fast forward and track up

button

6 Play/pause button 7 Fast reverse and track down

button

B To playback a compact disc n When CD is not in the player Hold a disc with a finger in the center hole while gripping the edge of the disc, then insert it in to the slot (with the label side up) and the player will automatically pull the disc into position. A 8 cm/3 inch CD may also be used without any adapter.

NOTE D DO NOT INSERT TWO DISCS INTO THE DISC INSERTION SLOT AT A TIME. D Be sure to always insert a disc with the label side up. If a disc is inserted with the label side down, it might be ejected or the player might shut off. D After the last song finishes, the player will automatically return to track 1 (the first song on the disc).

5-54

Legacy U.S.A..(ENG.)A2280BE–A

Audio

n When CD is in the player When the “"/❚

” button 6 is pressed, the player will start playback.

NOTE After the last song finishes, the player will automatically return to track 1 (the first song on the disc).

B To stop playback of a CD When the “"/❚ ” button 6 is pressed during playback of a CD, the CD stops playing temporarily. To let the CD resume playing, press the button again.

B To select a song from its beginning n Forward direction Briefly press the “""❚ ” button 5 to skip to the beginning of the next track. Each time the button is pressed, the indicated track number will increase.

n Backward direction Briefly press the “❚ AA” button 7 to skip to the beginning of the cur- rent track. Each time the button is pressed, the indicated truck num- ber will decrease.

B Fast forwarding and fast reverse n Fast forward Press the “""❚ ” button 5 continuously for more than 0.5 second to fast forward the disc. Release the button to stop fast forwarding.

n Fast reverse Press the “❚ AA” button 7 continuously for more than 0.5 second to fast reverse the disc. Release the button to stop fast reverse.

B Repeat playback Use this to play a certain track repeatedly. During playback, press the “RPT/RDM” button 2 and release it in less than 2 seconds. The “RPT” indicator will come on and the song will be played continuously. To

– CONTINUED –

5-55

❚ ❚ Legacy U.S.A..(ENG.)A2280BE–A

cancel the repeat mode, press the button again. Then the “RPT” indi- cator goes out, and normal playback mode is restored.

B Random playback Use this to play the tracks on the disc in random order. During play- back, press the “RPT/RDM” button 2 and hold it in for more than 2
seconds. The “RDM” indicator will come on and all songs on the disc will be played in a random order. To cancel the random mode, press the button again. Then the “RDM” indicator goes out, and normal playback mode is restored.

B Scan Press the “SCN/TOP” button 3 and release it in less than 2 seconds, and you can hear the first 10 seconds of each track to seach for the desired program. To continue listening to the program, press the “SCAN” button again. After all tracks on the disc has been scanned, normal playback mode is restored.

B Top Use this to return to the first track on the disc during playback. Press the “SCN/TOP” button 3 and hold it in for more than 2 seconds. Play- back returns to the beginning of the first track on the disc.

B To eject a disc from the player When a disc is being played back or when a disc is in the player, press the eject button “ The disc may be removed even when the ignition switch is in the “LOCK” position.

”. The disc will be ejected.

NOTE D Avoid driving the vehicle with a CD sticking out, because vibration might make it fall out. D To protect the disc, the disc is automatically loaded if it is left in the ejected position for more than approximately 15 seconds (Auto Reload). In this case, the disc is not played.

5-56

Legacy U.S.A..(ENG.)A2280BE–A

In-dash 6 CD auto changer (if equipped)

Audio

1 Disc slot 2 Disc indicators (disc No.1 to 6)

3 Disc select buttons

(disc No.1 to 6)

4 Eject button

HB5040BB

CAUTION

D Do not attempt to insert two or more discs into the slot at a time. Doing so can cause mechanical damage to the CD changer. D Use only music CDs identified by a D Do not use CDs listed below which could cause damage to the CD player.

mark.

D 3-inch (8 cm) compact disc. D Any disc with a peel-off or seal on it. D Any disc with scratches and/or dust. D Bent disc. D Cleaning disc. D CD accessory. (E.g., 3-inch (8 cm) disc adapter)

D Do not insert or remove any disc when the automatic transmis- sion selector lever is in the park position; the selector lever in that position can interfere with disc insertion or removal, causing scratches on the disc surface (for AT vehicles).

– CONTINUED –

5-57

Legacy U.S.A..(ENG.)A2280BE–A

B To insert a disc 1. Press one of the “Disc select” buttons 3 (numbered from 1 to 6) for which the disc indicator light 2 is “OFF”. The Disc indicator lights are located directly above the corresponding “Disc select” buttons. 2. The indicator will begin blinking. The blinking will last for 15 se- conds. During this period, insert a desired disc, and the disc will begin to play. (If any disc is not inserted during this period, the “Disc slot” 1
door will close. Repeat step 1.) Be sure to hold a disc with the label side (the side where titles are printed) up. 3. To insert another disc, repeat step 1 and 2 choosing a different disc select button.

B To insert six discs at a time 1. Press and hold the “Disc select” button number 1 until all disc indi- cators begin blinking (about 1.5 seconds). 2. The indicators will blink for 15 seconds. During this period, insert desired six discs. 3. When all discs are loaded, the first disc will begin to play. (If no disc is inserted within this 15 seconds, the entire disc load sequence will be canceled.)

B To remove a disc 1. Press the desired one of the “Disc select” buttons 3 (numbered from 1 to 6) for which the disc indicator light is on. 2. Press the “Eject button” 4. The selected disc will be ejected and the indicator light will begin blinking. 3. To remove another disc, repeat step 1 and 2 choosing a different “Disc select” button. (To remove discs when the ignition switch is in the “Lock” position, press the “Eject” button, and the first disc will be ejected. Press the “Eject” button again, and the next disc will be ejected and so on. At this time, the “Disc select” buttons are disabled.)

5-58

Legacy U.S.A..(ENG.)A2280BE–A