2001 Subaru Legacy Owners Manual

Download PDF Manual
See the label located under the driver’s door latch. Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Front seats Seat heater (if equipped) Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Armrest (if equipped) Folding down the rear seat — Station wagon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seatbelts Seatbelt safety tips Emergency Locking Retractor (ELR) Automatic/Emergency Locking Retractor (A/ELR) Seatbelt warning light and chime Fastening the seatbelt Seatbelt maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Front seatbelt pretensioners Child restraint systems Top tether anchorages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Built-in child restraint (if equipped) SRS airbag (Supplemental Restraint System airbag) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Vehicle with driver’s and front passenger’s SRS airbags and lap/shoulder restraints SRS frontal airbag SRS side airbag (if equipped) SRS airbag system monitors SRS airbag system servicing Precautions against vehicle modification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2 1-9 1-10 1-10 1-12 1-15 1-15 1-17 1-17 1-18 1-18 1-28 1-28 1-33 1-40 1-43 1-54 1-54 1-58 1-65 1-72 1-73 1-74 Legacy U.S.A..(ENG.)A2280BE–A Front seats WARNING D Never adjust the seat while driving to avoid the possibility of loss of vehicle control and of personal injury. D Never drive the vehicle with the head restraints removed be- cause they are designed to reduce the risk of serious neck injury in the event that the vehicle is struck from the rear. D Before adjusting the seat, make sure the hands and feet of rear seat passengers are clear of the adjusting mechanism. D Seatbelts provide maximum restraint when the occupant sits well back and upright in the seat. To reduce the risk of sliding un- der the seatbelt in a collision, the front seatbacks should be al- ways used in the upright position while the vehicle is running. If the front seatbacks are not used in the upright position in a colli- sion, the risk of sliding under the lap belt and of the lap belt slid- ing up over the abdomen will increase, and both can result in se- rious internal injury or death. D Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or death. D The SRS airbags deploy with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS air- bag needs enough space for deployment, the driver should al- ways sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. D Put children aged 12 and under in the rear seat properly re- strained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or im- properly restrained. Because children are lighter and weaker than 1-2 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags adults, their risk of being injured from deployment is greater. For that reason, we strongly recommend that ALL children (including those in child seats and those that have outgrown child restraint devices) sit in the REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is appropriate for the child’s age, height and weight. Secure ALL types of child restraint devices (including forward fac- ing child seat) in the REAR seats at all times. NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning child re- straint systems, see the “Child restraint systems” section in this chapter. Adjust the seatback to upright position. Sit well back and upright. Adjust the seatback to upright position. Sit well back and upright. Move the seat as far from the steering wheel as practical. HS0233 Move the seat as far back as possible. HB0290 – CONTINUED – 1-3 Legacy U.S.A..(ENG.)A2280BE–A Put children in the rearseat properly restrained at all times. Do not recline the seatback while vehicle is moving. HB0291 HS0247 B Fore and aft adjustment n Manual type HB1058BA Pull the lever upward and slide the seat to the desired position. Then release the lever and move the seatback and forth to make sure that it is securely locked into place. 1-4 Legacy U.S.A..(ENG.)A2280BE–A n Power seat (if equipped) Seat, seatbelt and SRS airbags HB1060BA To adjust the seat forward or backward, move the control switch for- ward or backward. B Seat cushion angle and height adjustment (Power seat only) HB1078BA HB1062BA To adjust the angle and height of the seat cushion, move the control switch in the corresponding direction. – CONTINUED – 1-5 Legacy U.S.A..(ENG.)A2280BE–A B Reclining the seatback n Manual type HB1072BA Pull the reclining lever up and adjust the seatback to the desired posi- tion. Then release the lever and make sure the seat is securely locked into place. The seatback placed in a reclined position can spring back upward with force when released. When operating the reclining lever to return the seatback, hold it lightly so that it may be raised back gradually. n Power seat (if equipped) To adjust the angle of the seatback, move the control switch. HB1084BA 1-6 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags NOTE While adjusting the seatback, you can not at the same time adjust the seat position or the seat cushion angle and height. B Head restraint adjustment HB1016BA OM-H2735 To raise the head restraint, pull it up. To lower it, push the head restraint down while pressing the release button on the top of the seatback. The best position for the head restraint is just above or level with the top of the ears. NOTE If the seatback is reclined rearward to the same level as the rear seat cushion with the head restraint removed, a wide flat bed is made available. WARNING D Never drive your car with the seats converted in a flat bed position. If you do so, occupants will have a greater chance of being injured even during simple deceleration, acceleration and cornering since no firm restraint will be available for them. D Before you lie on the flat bed to take a rest, read the descrip- tion “Parking your vehicle” in Chapter 7 carefully and follow the instructions. – CONTINUED – 1-7 Legacy U.S.A..(ENG.)A2280BE–A HBS011AA 1. Slide the front seat forward as far as possible. 2. Pull off the head restraint while pressing the release button. 3. Recline the seatback rearward up to the lowest position. Remem- ber to reinstall the head restraint whenever the seatback is raised back. B Lumbar support (if equipped) HB1059BA Pull the lever forward or backward. Pulling the lever forward will increase the amount of support for your lower back. 1-8 Legacy U.S.A..(ENG.)A2280BE–A Seat heater (if equipped) Seat, seatbelt and SRS airbags CAUTION D Use of the seat heater for a long period of time while the engine is not running can cause battery discharge. D Do not put anything on the seat which insulates against heat, such as a blanket, cushion, or similar items. This may cause the seat heater to overheat. D When cleaning the seat, do not use benzine, paint thinner, or any similar materials. The seat heater operates when the ignition switch is either in the “ACC” or “ON” position. HB1019BB HB1073BB To turn on the seat heater, push the “LO” or “HI” position on the switch, as desired, depending on the temperature. LO: Normal heating HI: Rapid heating The indicator located on the switch comes on when the seat heater is in operation. When the vehicle’s interior is warmed enough or before you leave the vehicle, be sure to turn the switch off. – CONTINUED – 1-9 Legacy U.S.A..(ENG.)A2280BE–A Rear seats WARNING D Seatbelts provide maximum restraint when the occupant sits well back and upright in the seat. Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or death. D Never allow passengers to ride on the folded rear seatback, in the cargo area. Doing so may result in serious injury or death. D Never stack luggage or other cargo higher than the top of the seatback because it could tumble forward and injure passengers in the event of a sudden stop or accident. D Secure skis and other lengthy items properly to prevent them from being thrown around inside the vehicle and causing serious injury during a sudden stop, a sudden steering or a rapid accel- eration. Sit well back and upright. J Armrest (if equipped) HB0302 WARNING To avoid the possibility of serious injury, passengers must never be allowed to sit on the center armrest while the vehicle is in mo- tion. 1-10 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HB1068BA To lower the armrest, pull on the top edge of the armrest. B Loading long objects WARNING D Secure long objects properly to prevent them from shooting forward and causing serious injury during a sudden stop or sharp cornering. Tie long objects down with a rope or something equivalent. D Avoid loading objects longer than 6.6 ft (2 m) and heavier than 55 lb (25 kg). Such objects can interfere with the driver’s proper operation of the car, possibly causing an accident and serious injury. HB1052BA HB1053BA – CONTINUED – 1-11 Legacy U.S.A..(ENG.)A2280BE–A Folding down the armrest and opening the seatback panel affords a loading space for long objects. To open the seatback panel, pull the panel down while pressing the release tab down. J Folding down the rear seat — Station wagon WARNING D After returning the rear seat to its original position, be certain to place all of the seatbelts and the tab attached to the seat cush- ion above the seat cushion. And make certain that the shoulder belts are fully visible. D Never permit anyone to ride in the cargo area. B Folding down the seatback HB1022BA HB1023BA Unlock the seatback by pulling the release knob and then fold the seatback down. B Folding down the seat cushion and seatback 1. Move the front seat forward. 2. Close the rear passengers’ cup holder and ashtray. 3. To remove the headrest (if so equipped), pull the headrest up while pressing the release button located on the backside of the seatback. 1-12 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HB1024BA 4. Store the seatbelts in the seatbelt pocket to prevent them from fal- ling below the cushion. HB1074BB 5. Raise the seat cushion by pulling up the tab. Make certain that the rear passenger’s cup holder is fully retracted HB1076BB – CONTINUED – 1-13 Legacy U.S.A..(ENG.)A2280BE–A before raising the seat cushion. HB1025BA 6. Unlock the seatback by pulling the release knob and fold the seat- back down. Confirm that the pin located at the bottom of the seat cushion is inserted into the slot at the top of the seatback. HB1027BA 7. Install the headrest (if so equipped) onto the backside of the seat- back. 1-14 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HB1028BA To return the rear seat to its original position, raise the seatback and seat cushion until they lock into place and make sure that they are securely locked. Make sure that the rear seatbelts are not under the seat cushion or seat- back. Place the headrests (if so equipped) back in their normal position. Seatbelts J Seatbelt safety tips WARNING D All persons in the vehicle should fasten their seatbelts BE- FORE the vehicle starts to move. Otherwise, the possibility of se- rious injury becomes greater in the event of a sudden stop or ac- cident. D All belts should fit snugly in order to provide full restraint. Loose fitting belts are not as effective in preventing or reducing injury. D Each seatbelt is designed to support only one person. Never use a single belt for two or more persons — even children. Other- wise, in an accident, serious injury or death could result. D Replace all seatbelt assemblies including retractors and at- taching hardware worn by occupants of a vehicle that has been in – CONTINUED – 1-15 Legacy U.S.A..(ENG.)A2280BE–A a serious accident. The entire assembly should be replaced even if damage is not obvious. D Put children aged 12 and under in the rear seat properly re- strained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or im- properly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater. For that reason, we strongly recommend that ALL children (including those in child seats and those that have outgrown child restraint devices) sit in the REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is appropriate for the child’s height and weight. Secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning the child restraint system, see the “Child restraint systems” section in this chapter. B Infants or small children Use a child restraint system that is suitable for your vehicle. See in- formation on “Child restraint systems” in this chapter. B Children If a child is too big for a child restraint system, the child should sit in the rear seat and be restrained using the seatbelts. According to ac- cident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. Never allow a child to stand up or kneel on the seat. If the shoulder portion of the belt crosses the face or neck, move the 1-16 1 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags child closer to the belt buckle to help provide a good shoulder belt fit. Care must be taken to securely place the lap belt as low as possible on the hips and not on the child’s waist. If the shoulder portion of the belt cannot be properly positioned, a child restraint system should be used. Never place the shoulder belt under the child’s arm or behind the child’s back. B Expectant mothers Expectant mothers also need to use the seatbelts. They should con- sult their doctor for specific recommendations. The lap belt should be worn securely and as low as possible over the hips, not over the waist. J Emergency Locking Retractor (ELR) The driver’s seatbelt has an Emergency Locking Retractor (ELR). The emergency locking retractor allows normal body movement but the retractor locks automatically during a sudden stop, impact or if you pull the belt very quickly out of the retractor. J Automatic/Emergency Locking Retractor (A/ELR) Each passenger’s seatbelt has an Automatic/Emergency Locking Re- tractor (A/ELR). The Automatic/Emergency Locking Retractor normally functions as an Emergency Locking Retractor (ELR). The A/ELR has an additional locking mode “Automatic Locking Retractor (ALR) mode” in- tended to secure a child restraint system. When the seatbelt is once drawn out completely and is then retracted even slightly, the retractor locks the seatbelt in that position and the seatbelt cannot be extended. As the belt is rewinding, clicks will be heard which indicate the retractor functions as ALR. When the seatbelt is retracted fully, ALR mode is re- leased. When securing a child restraint system on the passengers’ seats, the seatbelt must be changed over to the Automatic Locking Retractor (ALR) mode. When the child restraint system is removed, make sure that the retractor is restored to the Emergency Locking Retractor (ELR) function by allow- ing the seatbelt to retract fully. – CONTINUED – 1-17 Legacy U.S.A..(ENG.)A2280BE–A For instructions on how to convert the retractor to the ALR mode and re- store it to the ELR mode, see the “Child restraint systems” section in this chapter. J Seatbelt warning light and chime Your vehicle is equipped with a seatbelt warning device at the driver’s seat. This device causes the seatbelt warning light on the instrument panel to light up for about six seconds when the ignition switch is turned to the “ON” position to remind the driver to wear the seatbelt. If the driver’s seatbelt is not fastened, a warning chime sounds at the same time. J Fastening the seatbelt WARNING D Never use a belt that is twisted or reversed. In an accident, this can increase the risk or severity of injury. D Never place the shoulder belt under the arm or behind the back. If an accident occurs, this can increase the risk or severity of injury. D Keep the lap belt as low as possible on your hips. In a colli- sion, this spreads the force of the lap belt over stronger hip bones instead of across the weaker abdomen. D Seatbelts provide maximum restraint when the occupant sits well back and upright in the seat. To reduce the risk of sliding un- der the seatbelt in a collision, the front seatbacks should be al- ways used in the upright position while the vehicle is running. If the front seatbacks are not used in the upright position in a colli- sion, the risk of sliding under the lap belt and of the lap belt slid- ing up over the abdomen will increase, and both can result in se- rious internal injury or death. D Do not put cushions or any other materials between occupants and seatbacks or seat cushions. If you do so, the risk of sliding under the lap belt and of the lap belt sliding up over the abdomen will increase, and both can result in serious internal injury or death. 1-18 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Always wear the seatbelts correctly. Never place the shoulder belt under the arm or behind the back. Adjust the seatback to upright position. Sit well back and upright. HS0230 HS0231 CAUTION Metallic parts of the seatbelt can become very hot in a vehicle that has been closed up in sunny weather; they could burn an oc- cupant. Do not touch such hot parts until they cool. B Front seatbelts OM-H0043 OM-H0044 1. Adjust the seat position: Driver’s seat: Adjust the seatback to the upright position. Move the seatback as far from the steering wheel as practical while still main- taining full vehicle control. Front passenger’s seat: Adjust the seatback to the upright position. Move the seat as far back as possible. – CONTINUED – 1-19 Legacy U.S.A..(ENG.)A2280BE–A 2. Sit well back in the seat. 3. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving it a strong pull, then pull it out slowly again. 4. Insert the tongue plate into the buckle until you hear a click. 5. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist. n Adjusting the front seat shoulder belt anchor height WARNING When wearing the seatbelts, make sure the shoulder portion of the webbing does not pass over your neck. If it does, adjust the seatbelt anchor to a lower position. Placing the shoulder belt over the neck may result in neck injury during sudden braking or in a collision. HB1029BB The shoulder belt anchor height should be adjusted to the position best suited for you. To lower the anchor height, push the release but- ton and slide the anchor down. To raise the anchor height, slide the anchor up. Pull down on the anchor to make sure that it is locked in place. 1-20 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Always adjust the anchor height so that the shoulder belt passes over the middle of the shoulder without touching the neck. n Unfastening the seatbelt Push HB0303 Push the button on the buckle. Before closing the door, make sure that the belts are retracted prop- erly to avoid catching the belt webbing in the door. B Rear seatbelts (except rear center seatbelt on wagon) OM-H0043 OM-H0044 1. Sit well back in the seat. 2. Pick up the tongue plate and pull the belt out slowly. Do not let it get twisted. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving a strong pull on it, then pull it out slowly again. – CONTINUED – 1-21 Legacy U.S.A..(ENG.)A2280BE–A 3. Insert the tongue plate into the buckle until you hear a click. 4. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist. n Unfastening the seatbelt Push Push the button on the buckle. HB0303 Before closing the door, make sure that the belts are retracted prop- erly to avoid catching the belt webbing in the door. B Rear center seatbelt on wagon model WARNING D Fastening the seatbelt with the webbing twisted can increase the risk or severity of injury in an accident. When fastening the belt after it is pulled out from the retractor, especially when inserting the connector’s tongue plate into the mating buckle (on right-hand side), always check that the webbing is not twisted. D Be sure to fasten both tongue plates to the respective buckles. If the seatbelt is used only as a shoulder belt (with the connector’s tongue plate not fastened to the connector’s buckle on the right-hand side), it cannot properly restrain the wearer in position in an accident, possibly resulting in serious injury or death. 1-22 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HB1030BA HB1031BA 1. Center seatbelt tongue plate 2. Connector (tongue) 3. Connector (buckle) 4. Center seatbelt buckle HS1017BB 1. Pull out the seatbelt slowly from the overhead retractor. HB1032BA – CONTINUED – 1-23 Legacy U.S.A..(ENG.)A2280BE–A HB1033BA 2. After confirming that the webbing is not twisted, insert the connec- tor (tongue) attached at the webbing end into the buckle on the right- hand side until a click is heard. If the belt stops before reaching the buckle, return the belt slightly and pull it out more slowly. If the belt still cannot be unlocked, let the belt retract slightly after giving it a strong pull, then pull it out slowly again. HB1034BA 3. Insert the center seatbelt tongue plate in the center seatbelt buckle marked “CENTER” on the left-hand side until it clicks. To make the lap part tight, pull up on the shoulder belt. And place the lap belt as low as possible on your hips, not on your waist. 1-24 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HS1019BA n Unfastening the seatbelt Push HS0317 Push the release button of the center seatbelt buckle (on the left-hand side) to unfasten the seatbelt. NOTE When the seatback is folded down for greater luggage space, it is necessary to disconnect the connector. – CONTINUED – 1-25 Legacy U.S.A..(ENG.)A2280BE–A CAUTION D Do not allow the retractor to roll up the seatbelt too quickly. Otherwise, the metal tongue plates may hit against the trim, resulting in damaged trim. D Have the seatbelt fully rolled up so that the tongue plates are neatly stored. A hanging tongue plate can swing and hit against the trim during driving, causing damage to the trim. HB1036BA HB1037BA 1. Insert a key or other hard pointed object into the slot in the con- nector (buckle) on the right-hand side and push it in, and the connec- tor (tongue) plate will disconnect from the buckle. HB1038CA HB1048BA 2. Allow the retractor to roll up the belt. You should hold the webbing end and guide it back into the retractor while it is rolling up. Neatly 1-26 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags store the tongue plates in the recess in the retractor and then insert the connector (tongue) plate into the slot located at the front of the recess. NOTE When folding down the rear seat cushion, store the seatbelts in the seatbelt pocket to prevent them falling below the cushion. HB1074BB HB1076BB – CONTINUED – 1-27 Legacy U.S.A..(ENG.)A2280BE–A J Seatbelt maintenance CAUTION D Keep the belts free of polishes, oils, chemicals and particularly battery acid. D Never attempt to make modifications or changes that will pre- vent the seatbelt from operating properly. To clean the seatbelts, use a mild soap and lukewarm water. Never bleach or dye the belts because this could seriously affect their strength. Inspect the seatbelts and attachments including the webbing and all hardware periodically for cracks, cuts, gashes, tears, damage, loose bolts or worn areas. Replace the seatbelts even if only minor damage is found. Front seatbelt pretensioners WARNING D To obtain maximum protection, occupants should sit in an up- right position with their seatbelts properly fastened. Refer to “Seatbelts” section in this chapter. D Do not modify, remove or strike the front seatbelt retractor as- semblies or surrounding area. This could result in accidental ac- tivation of the seatbelt pretensioners or could make the system inoperative, possibly resulting in serious injury. Seatbelt preten- sioners have no user-serviceable parts. For required servicing of front seatbelt retractors equipped with seatbelt pretensioners, see your nearest SUBARU dealer. D When discarding front seatbelt retractor assemblies or scrap- ping the entire car due to collision damage or for other reasons, consult your SUBARU dealer. 1-28 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Seatbelt retractor assembly (Pretensioner) HB0373 The driver’s and front passenger’s seatbelts have a seatbelt preten- sioner. The seatbelt pretensioners are designed to be activated in the event of an accident involving a moderate to severe frontal collision. The pretensioner sensor also serves as a SRS frontal airbag sensor. If the sensor detects a certain predetermined amount of force during a frontal collision, the front seatbelt is quickly drawn back in by the re- tractor to take up the slack so that the belt more effectively restrains the front seat occupant. When a seatbelt pretensioner is activated, an operating noise will be heard and a small amount of smoke will be released. These occur- rences are normal and not harmful. This smoke does not indicate a fire in the vehicle. Once the seatbelt pretensioner has been activated, the seatbelt re- tractor remains locked. Consequently, the seatbelt can not be pulled out and retracted. NOTE D Seatbelt pretensioners are not designed to activate in minor frontal impacts, in side or rear impacts or in roll-over accidents. D The driver’s seat and passenger’s seat pretensioners and fron- tal airbag operate simultaneously. D Pretensioners are designed to function on a one-time-only ba- sis. In the event that a pretensioner is activated, both the driver’s and front passenger’s seatbelt retractor assemblies must be re- – CONTINUED – 1-29 Legacy U.S.A..(ENG.)A2280BE–A placed and only by an authorized SUBARU dealer. When replac- ing seatbelt retractor assemblies, use only genuine SUBARU parts. D If either front seatbelt does not retract or cannot be pulled out due to a malfunction or activation of the pretensioner, contact your SUBARU dealer as soon as possible. D If the front seatbelt retractor assembly or surrounding area has been damaged, contact your SUBARU dealer as soon as pos- sible. D When you sell your vehicle, we urge you to explain to the buy- er that it has seatbelt pretensioners by alerting him to the con- tents of this section. B System monitors HB4010EC A diagnostic system continually monitors the readiness of the seatbelt pretensioner while the vehicle is being driven. The seatbelt preten- sioners share the control module with the airbag system. Therefore, if any malfunction occurs in a seatbelt pretensioner, the SRS airbag sys- tem warning light will illuminate. The SRS airbag system warning light will show normal system operation by lighting for about 6 seconds when the ignition key is turned to the “ON” position. The following components are monitored by the indicator: D Front sub sensor (Right hand side) D Front sub sensor (Left hand side) D Airbag control module (including impact sensors) 1-30 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags D Seatbelt pretensioner (Driver’s side) D Seatbelt pretensioner (Passenger’s side) D All related wiring In the event of a malfunction indicated by any of following, the vehicle should be taken promptly to your nearest SUBARU dealer to have the system checked. Unless checked and repaired, the seatbelt preten- sioners and airbags will not function reliably: D Flashing or flickering of the indicator light. D No illumination of the warning light when the ignition switch is first turned to the “ON” position. D Continuous illumination of the warning light. D Illumination of the warning light while driving. B System servicing WARNING D When discarding a seatbelt retractor assembly or scrapping the entire car damaged by a collision, consult your SUBARU deal- er. D Tampering with or disconnecting the system’s wiring could re- sult in accidental activation of the seatbelt pretensioner and/or airbag or could make the system inoperative, which may result in serious injury. The wiring harnesses of the seatbelt pretensioner and SRS airbag systems are covered with yellow insulation and the connectors of the system are yellow for easy identification. Do not use electrical test equipment on any circuit related to the seatbelt pretensioner and airbag systems. For required servicing of the seatbelt pretensioner, see your nearest SUBARU dealer. CAUTION The front sub sensors are located in both front fenders and the airbag control module including the impact sensors is located under the center console. If you need service or repair in those areas or near the front seatbelt retractors, we recommend that you have an authorized SUBARU dealer perform the work. – CONTINUED – 1-31 Legacy U.S.A..(ENG.)A2280BE–A NOTE If the front part of the vehicle is damaged in an accident to the extent that the seatbelt pretensioner does not operate, contact your SUBARU dealer as soon as possible. B Precautions against vehicle modification CAUTION Do not perform any of the following modifications. Such modifi- cations can interfere with proper operation of the seatbelt perten- sioners. D Attachment of any equipment (bush bar, winches, snow plow, skid plate, etc.) other than SUBARU genuine accessory parts to the front end. D Modification of the suspension system or front end structure. D Installation of a tire of different size and construction from the tires specified on the tire placard attached to the door jamb. Always consult your SUBARU dealer if you want to install any acces- sory parts to your vehicle. 1-32 1 Legacy U.S.A..(ENG.)A2280BE–A Child restraint systems Seat, seatbelt and SRS airbags WARNING D Never let a passenger hold a child on his or her lap while the vehicle is moving. The passenger cannot protect the child from injury in a collision, because the child will be caught between the passenger and objects inside the vehicle. Additionally, holding a child in your lap or arms in the front seat exposes that child to another serious danger. Since the SRS airbag deploys with con- siderable speed and force, the child could be injured or even killed. D Put children aged 12 and under in the rear seat properly re- strained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or im- properly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater. For that reason, be sure to secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. You should choose a restraint device which is appropriate for the child’s age, height and weight. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. D SINCE YOUR VEHICLE IS EQUIPPED WITH A PASSENGER’S SRS AIRBAG, DO NOT INSTALL A REARWARD FACING CHILD SAFETY SEAT IN THE FRONT PASSENGER’S SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Children should be properly restrained in the rear seat at all times. Never allow a child to stand up, or to kneel on the front passenger’s seat. The SRS airbag deploys with considerable force and can injure or even kill the child. – CONTINUED – 1-33 Legacy U.S.A..(ENG.)A2280BE–A Never hold a child on your lap or in your arms in the front passenger’s seat or any other seat. HB0308 HS1031BB Never install rearward facing child safety seat in the front passen- ger’s seat. Never allow a child to stand up, or to kneel on the front passenger’s seat or any other seat HB0306 HB0307 WARNING D Child restraint systems and seatbelts can become hot in a ve- hicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint system before you place a child in it. D Do not leave an unsecured child restraint system in your vehi- cle. Unsecured child restraint systems can be thrown around in- side of the vehicle in a sudden stop, turn or accident; it can strike and injure vehicle occupants as well as result in serious injuries or death to the child. Infants and small children should always be placed in an infant or child restraint system in the rear seat while riding in the vehicle. You should use an infant or child restraint system that meets Federal Motor Vehicle 1-34 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Safety Standards or Canada Motor Vehicle Safety Standards, is compat- ible with your vehicle and is appropriate for the child’s age and size. All child restraint systems are designed to be secured in vehicle seats by lap belts or the lap belt portion of a lap/shoulder belt (except those cov- ered under the section in this manual, entitled “Instruction of child re- straint systems by use of lower and tether anchorages”). Children could be endangered in an accident if their child restraints are not properly secured in the vehicle. When installing the child restraint system, carefully follow the manufacturer’s instructions. According to accident statistics, children are safer when properly re- strained in the rear seating positions than in the front seating positions. All U.S. states and Canadian provinces require that infants and small children be restrained in an approved child restraint system at all times while the vehicle is moving. B Installing child restraint systems with seatbelt NOTE When the child restraint system is no longer in use, remove it and restore the ELR function of the retractor. That function is restored by allowing the seatbelt to retract fully. CAUTION When you install a child restraint system, follow the manufactur- er’s instructions supplied with it. After installing the child re- straint system, check to ensure that it is held securely in posi- tion. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be in- creased. – CONTINUED – 1-35 Legacy U.S.A..(ENG.)A2280BE–A HB1080BA 1. Set the child restraint system in the seating position. 2. Run the lap and shoulder belt through or around the child restraint system following the instructions provided by its manufacturer. If the shoulder belt goes in front of the child’s face or neck, put it behind the child restraint system. 3. Insert the tongue plate into the buckle. 4. Take up the slack in the lap belt. 5. Pull out the seatbelt fully from the retractor to change the retractor over from the Emergency Locking Retractor (ELR) to the Automatic Locking Retractor (ALR) function. Then, allow the belt to rewind into the retractor. As the belt is rewinding, clicks will be heard which indi- cate the retractor functions as ALR. 6. Before having a child sit in the child restraint system, move it back and forth to check if it is firmly secured. Sometimes a child restraint can be more firmly secured by pushing it down into the seat cushion and then tightening the seatbelt. 7. Pull at the shoulder portion of the belt to confirm that it cannot be pulled out (ALR properly functioning). If the child restraint system requires a top tether, latch the hook onto the top tether anchor and tighten the top tether. See the “Top tether anchorages” for additional instructions. 1-36 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HB1083BA HBS065BA 8. To remove the child restraint system, press the release button on the seatbelt buckle and allow the belt to retract completely. The belt will return to the ELR mode. If you have any question concerning this type of child restraint sys- tem, ask your SUBARU dealer. B Installation of child restraint systems by use of lower and teth- er anchorages Some types of child restraint systems can be installed on the rear seat of your vehicle without use of the seatbelts. Such child restraint systems are secured to the dedicated anchorages provided on the vehicle body. HB1086BA Your vehicle is equipped with four lower anchorages (bars) and three upper anchorages (tether anchorages) for accommodating such child restraint systems. – CONTINUED – 1-37 Legacy U.S.A..(ENG.)A2280BE–A HB1090BA HB1087BA The lower anchorages (bars) are used for installing a child restraint system only on the rear seat window-side seating positions. For each window-side seating position, two lower anchorages are provided. The tether anchorages (upper anchorages) are provided for all the seating positions (middle and both window-side ones) of the rear seat. HB1085BA HB1088BA You will find marks “Child” at the bottom of the rear seat seatbacks. These marks indicate the positions of the lower anchorages (bars). Each lower anchorage is located where the seat cushion meets the seatback. 1-38 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags CAUTION When you install a child restraint system, follow the manufactur- er’s instructions supplied with it. After installing the child re- straint system, check to ensure that it is held securely in posi- tion. If it is not held tight and secure, the danger of your child suffering personal injury in the event of an accident may be in- creased. 1. Use the “Child” marks to locate the two lower anchorages (bars) for the position where you want to install the child restraint system. NOTE On a vehicle with a built-in child restraint, if you are required to use a child restraint system and the built-in child restraint at the same time, it is recommended that you install the child restraint system on the rear left side (behind the driver’s seat). The built-in child restraint is located toward the right side. For this reason, certain child restraint systems will be tilted if installed on the right side and they cannot be properly secured. 2. While following the instructions supplied by the child restraint sys- tem manufacturer, connect the connectors of the child restraint sys- tem to the lower anchorages. When the connectors are fastened, make sure that the adjacent seat- belts are not caught. If your child restraint system is of a flexible attachment type (which uses tether straps to connect the child restraint system proper to the lower anchorages), firmly tighten the straps after connecting the con- nectors. 3. Connect the top tether hook to the tether anchorage and firmly tighten the tether. For information on how to set the top tether, read the following “Top tether anchorages”. 4. Before seating a child in the child restraint system, try to move seat back and forth to verify that it is held securely in position. If you have any question concerning this type of child restraint sys- tem, ask your SUBARU dealer. – CONTINUED – 1-39 Legacy U.S.A..(ENG.)A2280BE–A J Top tether anchorages B Anchorage location HBS061BB HB1077BC Three anchorages, i.e., ones for the right, center and left positions, are already installed on the rear parcel shelf (on Sedan) or on the rear edge of the roof (on Staion wagon). 1-40 Legacy U.S.A..(ENG.)A2280BE–A B To hook the top tether n Sedan Seat, seatbelt and SRS airbags CAUTION When the child restraint system is to be secured using the top tether, always pass the top tether under the headrest between the headrest stay posts. If the top tether is routed over the headrest, it may not be properly tensioned, resulting in an unsteady child restraint system. HBS063BA HBS064BB 1. Remove the headrest at the seating position where the child seat has been installed with the seatbelt or lower anchorages; lift up the headrest while pressing the release button. 2. Fasten the top tether hook of the child safety to the appropriate up- per anchorage. – CONTINUED – 1-41 Legacy U.S.A..(ENG.)A2280BE–A HBS065BA HB1064BA 3. Tighten the top tether securely. 4. Reinstall the headrest in such a way that the top tether is routed between the headrest stay posts. n Station wagon CAUTION Always remove the headrest when mounting a child restraint sys- tem with a top tether. Otherwise, it may happen that the top tether cannot be fastened tightly. HBS005BA HB1081BB 1. Remove the headrest (if so equipped) at the seating position where the child restraint system has been installed with the seatbelt or lower anchorages; lift up the headrest while pressing the release but- 1-42 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags ton. Store the headrest in the cargo area. Avoid placing the headrest in the passenger compartment to prevent it from being thrown around in the passenger compartment in a sudden stop or a sharp turn. 2. Fasten the top tether hook of the child restraint system to the ap- propriate upper anchorage. 3. Tighten the top tether securely. Built-in child restraint (if equipped) Refer to the diagram below to become familiar with the parts of this built- in child restraint. 1 Lap-shoulder belt 2 Chest clip 3 Release button 4 Crotch belt 5 Warning label 6 Fastening strap HBS067BB 7 Child restraint cushion 8 Belt buckle 9 Tongue plates Q Maximum shoulder height indicator label W Removable pad – CONTINUED – 1-43 Legacy U.S.A..(ENG.)A2280BE–A The child restraint is designed for use only by children who weigh be- tween 9.05 kg (20 lb.) and 18.09 kg (40 lb.), whose height is 110 cm (44.3 in.) or less, who are capable of sitting upright alone and whose shoulder height is below the shoulder belt slot. The child should also be at least one year old. It is important to use a rear-facing child restraint until the child is about a year old. A rear-facing restraint gives the child’s head, neck and body the support they would need in a collision. See the “Child restraint systems” section in this manual. WARNING Do not use the built-in child restraint for infants who require a rear-facing child restraint. In an accident, serious crippling injury or death could result if the built-in restraint is used for the infant. If the child exceeds the maximum weight and height capacities of the built-in child restraint (maximum weight of 18.09 kg (40 lb.) and maxi- mum height of 110 cm (44.3 in.)), do not use the built-in child restraint. The child should use either the vehicle’s seatbelts or an approved after- market booster seat, if necessary. The built-in child restraint system conforms to Federal Motor Vehicle Safety Standard No. 213 and Canada Motor Vehicle Safety Standard No. 213.4. According to accident statistics, children are safer when properly re- strained in the rear seating position than in the front seating position. Children aged 12 and under should not sit in the front seat of a car equipped with a passenger’s SRS airbag. WARNING D Make sure the child is securely restrained with the built-in child restraint. D Failure to follow the manufacturer’s instructions on the use of this child restraint system can result in your child striking the ve- hicle’s interior during a sudden stop or crash. 1-44 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags D Snugly adjust the belts provided with this child restraint around your child. D The built-in child restraint should be used for only one child at a time. Using it for two or more children at the same time could result in serious injury or death in an accident. D Do not use the center lap and shoulder belt with the child re- straint. A child using the center seatbelt could slide forward and out from under the seatbelt in a sudden stop or an accident, re- sulting in serious injury to the child. HBS047BA WARNING D Do not use another child restraint system over the opened built-in child restraint. Because a child restraint system cannot be secured on the built-in restraint cushion, the restraint could fall down during sudden braking, a sharp turn or in an accident, causing serious injury to the child in it. D Always keep the child restraint equipped rear seatback locked securely in place when the child restraint is in use. Otherwise, in an accident, serious injury or death to a child could result if the seatback falls down. D The built-in child restraint, especially metallic parts, can be- come hot in a vehicle that has been closed up in sunny weather; they could burn a small child. Check the child restraint before you place a child in it. – CONTINUED – 1-45 Legacy U.S.A..(ENG.)A2280BE–A CAUTION Be careful not to damage the belt webbing or hardware. Take care that they do not get caught or pinched in the seatback. The lap-shoulder belts of the built-in child restraint are equipped with an automatic locking retractor (ALR) that automatically locks when both tongue plates are latched into the belt buckle and the belts retract. B Placing a child in the built-in child restraint 1. Before using the built-in child restraint, make sure the vehicle’s rear seatback is locked securely in place. HBS068BB 2. Unfasten the fastening strap and lower the child restraint cushion. 3. Read the information and warnings on the child restraint cushion. Check the child’s size and weight to be sure the child is not too small or too large for the child restraint. 1-46 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HBS049BA 4. If the left and right halves of the chest clip are fastened together, separate them by squeezing the release tabs. HBS050BA HBS051BB 5. Pull down the seatback part of the removable pad. Make sure the child’s shoulders are at or below the maximum shoulder height indi- cated on the label attached to the seatback. The child restraint pad is attached by hook and loop fasteners (VelcroR). WARNING If the child’s shoulders are above the maximum shoulder height indicated on the label, do not use the built-in child restraint. If used, the built-in restraint cannot restrain the child properly, which may result in serious injury to the child in an accident. – CONTINUED – 1-47 Legacy U.S.A..(ENG.)A2280BE–A The child should use eigher the vehicle’s seatbelts or an ap- proved aftermarket booster seat, if necessary. HBS051CB HBS050CB 6. Press the removable pad against the hook and loop fasteners (VelcroR) and install the pad to the seatback. Make sure the belts go through the slots in the pad. WARNING If you remove the removable pad for cleaning or other purposes, do not use the built-in child restraint. If an accident occurs, the absence of the pad can increase the risk or severity of injury to the child. HBS052BA HBS053BB 7. Sit the child on the child restraint. 1-48 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags 8. Pull out one side of the lap-shoulder belt and place it over the child’s shoulder. Insert the tongue plate into the buckle until it clicks. If both sides of the belt are pulled out, the belts will lock. If the belts lock, allow them to fully retract to unlock the retractor. Then pull out only one side of the belt. 9. Pull out the other side of lap-shoulder belt and place it over the child’s shoulder in a single motion. Insert the tongue plate into the buckle until it clicks. Once the belt retracts even slightly, the ALR will be activated and both belts will lock. If the belt stops before the tongue reaches the buckle, allow both belts to fully retract to unlock the retractor and then separately pull out the belts and buckle them again. 10. Allow both belts to tighten snugly against the child’s shoulders. Because of the ALR function, the belts cannot be pulled out simulta- neously from the retractor. The color green must appear in the indicator window on each tongue when buckled. If the color red appears in the window, the tongue is not buckled. WARNING After inserting the tongue plates, make sure the tongue plates and buckle are locked and that the lap-shoulder belts and crotch belt are not twisted. If the restraint is used with the tongues and buckle not locked and/or with the belts twisted, the risk or severi- ty of injury to the child could increase in an accident. CAUTION If the child restraint belts do not function normally, contact your authorized SUBARU dealer immediately. – CONTINUED – 1-49 Legacy U.S.A..(ENG.)A2280BE–A HBS054BA HBS055BB 11. Fasten the right and left halves of the chest clip at the level of the child’s armpits. The color green must appear in the indicator window when fastened. If the color red appears in the window, the clip is not securely latched. The purpose of the clip is to keep the shoulder belts positioned cor- rectly on the shoulders. WARNING An unfastened chest clip will not help keep the belts on the child’s shoulders. In a sudden stop or in an accident, the child may go too far forward and be seriously injured. Make sure the chest clip is fastened at all times. 12. If the belts are loose, pull down on lap parts of the belts to take in the slack of the lap and shoulder belts. 13. Pull the belts toward you to make sure the belt buckle is properly fastened and the retractor is locked. 14. If the belts become too tight, unbuckle the buckle and allow both belts to fully retract to unlock the retractor, then reinsert both tongue plates. 1-50 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags HBS056BA 15. Move the chest clip to the middle of the child’s chest so that the position of the shoulder portion of each belt is centered on the child’s shoulder. The belts should be away from the child’s face and neck, but not falling off the child’s shoulders. B Removing the child from the built-in child restraint HBS057BA HBS058BB 1. Disconnect the chest clip by squeezing the release tabs together and pulling the two sides apart. 2. Press the release button on the buckle. 3. Move both belts off the child’s shoulders. Because the ALR is activated, hold either the left or right shoulder belt out fully while helping slide the child’s arms out of the belts. 4. Allow the belts to fully retract. – CONTINUED – 1-51 Legacy U.S.A..(ENG.)A2280BE–A B Storing the built-in child restraint Always properly store the built-in child restraint before using the regu- lar lap-shoulder belt for the rear-center seating position. HBS066BA HBS069BA 1. Fasten the chest clip. 2. Stow the belt buckle into the recess of the child restraint cushion. 3. Fold the child restraint cushion up into the seatback. 4. Fasten the fastening strap on to the seatback by pressing it against the hook and loop fasteners (VelcroR). B Replacing restraint system parts after a collision WARNING Replace the built-in child restraint equipped vehicle seatback as- sembly if the child restraint was in use during a serious collision. The built-in restraint may be severely weakened. In a subsequent accident, it might not be able to provide adequate protection. The entire assembly should be replaced even if damage is not ob- vious. 1-52 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags B Maintenance CAUTION D Keep the belts free of polishes, oils, chemicals and particularly battery acid as they may weaken the belts. D Never attempt to make modifications or changes that will pre- vent the built-in child restraint from operating properly. The built-in child restraint may be cleaned with mild soap and luke- warm water. Do not use household cleaners. They may weaken the belts or damage plastic parts. Keep the built-in child restraint belts clean and dry. Clean the belts with only a mild soap and lukewarm water. Never bleach or dye the belts because this could seriously affect their strength. The removable pad is attached to the child restraint cushion and seat- back with hook and loop fasteners (VelcroR). It is possible to remove the pad, hand wash it in cold water and dry it in the shade. Never bleach or iron the pad. Periodically inspect the belts, tongue plates, buckle, clip, retractor and anchorages of the built-in child restraint. If these parts are dam- aged and/or do not function properly, contact your authorized SUBARU dealer for replacement parts. – CONTINUED – 1-53 Legacy U.S.A..(ENG.)A2280BE–A *SRS airbag (Supplemental Restraint System airbag) *SRS: This stands for supplemental restraint system. This name is used because the airbag system supplements the vehicle’s seatbelts. J Vehicle with driver’s and front passenger’s SRS air- bags and lap/shoulder restraints WARNING D To obtain maximum protection in the event of an accident, the driver and all passengers in the vehicle should always wear seat- belts when the vehicle is moving. The SRS airbag is designed only as a supplement to the primary protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. In combination with the seatbelts, it offers the best combined protection in case of a serious accident. Not wearing a seatbelt increases the chance of severe injury or death in a crash even when the car has the SRS airbag. For instructions and precautions concerning the seatbelt system, see the “Seatbelts” sections in this chapter. D Do not sit or lean unnecessarily close to the SRS airbag. Be- cause the SRS airbag deploys with considerable speed – faster than the blink of an eye – and force to protect in high speed colli- sions, the force of an airbag can injure an occupant whose body is too close to SRS airbag. It is also important to wear your seatbelt to help avoid injuries that can result when the SRS airbag contacts an occupant not in proper position such as one thrown forward during pre-accident braking. Even when properly positioned, there remains a possibility that an occupant may suffer minor injury such as abrasions and bruises to the face or arms because of the SRS airbag deploy- ment force. 1-54 1 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags D The SRS airbags deploy with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS air- bag needs enough space for deployment, the driver should al- ways sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. D Do not place any objects over or near the SRS airbag cover or between you and the SRS airbag. If the SRS airbag deploys, those objects could interfere with its proper operation and could be propelled inside the car and cause injury. D Put children aged 12 and under in the rear seat properly re- strained at all times. The SRS airbag deploys with considerable speed and force and can injure or even kill children, especially if they are 12 years of age and under and are not restrained or im- properly restrained. Because children are lighter and weaker than adults, their risk of being injured from deployment is greater. For that reason, we strongly recommend that ALL children (in- cluding those in child seats and those that have outgrown child restraint devices) sit in the REAR seat properly restrained at all times in a child restraint device or in a seatbelt, whichever is ap- propriate for the child’s age, height and weight. Secure ALL types of child restraint devices (including forward facing child seats) in the REAR seats at all times. According to accident statistics, children are safer when properly restrained in the rear seating positions than in the front seating positions. For instructions and precautions concerning the child restraint system, see the “Child restraint systems” section in this chapter. D NEVER INSTALL A REARWARD FACING CHILD SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Never allow a child to stand up, or to kneel on the front pas- senger’s seat, or never hold a child on your lap or in your arms. – CONTINUED – 1-55 Legacy U.S.A..(ENG.)A2280BE–A The SRS airbag deploys with considerable force and can injure or even kill the child. Put children in the REAR seat prop- erly restrained at all times. HB0291 CAUTION D When the SRS airbag deploys, some smoke will be released. This smoke could cause breathing problems for people with a history of asthma or other breathing trouble. If you or your pas- sengers have breathing problems after SRS airbag deploys, get fresh air promptly. D A deploying SRS airbag releases hot gas. Occupants could get burnt if they come into direct contact with the hot gas. The supplemental restraint system (SRS) consists of two airbags (driver’s and front passenger’s frontal airbags) or four airbags (driver’s and front passenger’s frontal airbags and driver’s and front passenger’s side air- bags). These SRS airbags are designed only as a supplement to the prima- ry protection provided by the seatbelt. The system also controls front seatbelt pretensioners. For operation, instructions are precautions concerning the seatbelt pretensioner, see the “Front seatbelt pretensioner” section in this chapter. 1-56 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags NOTE When you sell your vehicle, we urge you to explain to the buyer that it is equipped with SRS airbags by alerting him to the applicable section in this owner’s manual. B Components 1 Airbag control module (including impact sensors) 2 Airbag module (driver’s side) 3 Airbag module 7 Seatbelt pretensioner (passenger’s side) 8 Side airbag module (driver’s side — if equipped) HB1079DB (passenger’s side) 4 Front sub sensor (left hand side) 5 Front sub sensor (right hand side) 6 Seatbelt pretensioner (driver’s side) 9 Side airbag module (passenger’s side — if equipped) Q Side airbag sensor (driver’s side) W Side airbag sensor (passenger’s side) E Airbag wiring (yellow) – CONTINUED – 1-57 Legacy U.S.A..(ENG.)A2280BE–A J SRS frontal airbag WARNING D NEVER INSTALL A REARWARD FACING CHILD SAFETY SEAT IN THE FRONT SEAT. DOING SO RISKS SERIOUS INJURY OR DEATH TO THE CHILD BY PLACING THE CHILD’S HEAD TOO CLOSE TO THE SRS AIRBAG. D Never allow a child to stand up, or to kneel on the front pas- senger’s seat, or never hold a child on your lap or in your arms. The SRS airbag deploys with considerable force and can injure or even kill the child. D The SRS airbag deploys with considerable speed and force. Occupants who are out of proper position when the SRS airbag deploys could suffer very serious injuries. Because the SRS air- bag needs enough space for deployment, the driver should al- ways sit upright and well back in the seat as far from the steering wheel as practical while still maintaining full vehicle control and the front passenger should move the seat as far back as possible and sit upright and well back in the seat. It is also important to wear your seatbelt to help avoid injuries that can result when the SRS airbag contacts an occupant not in proper position such as one thrown toward the front of the car during pre-accident braking. Never install rearward facing child restraint system in the front passen- ger’s seat. Never allow a child to stand up, or to kneel on the front passenger’s seat HB0306 HB0307 1-58 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Never hold a child on your lap or in your arms. Adjust the seatback to upright position. Sit well back and upright. HB0308 Move the seat as far from the steering wheel as practical. HS0233 Adjust the seatback to upright position. Sit well back and upright. Move the seat as far back as possible. HB0290 WARNING D Do not put any objects over the steering wheel pad and dash- board. If the SRS frontal airbag deploys, those objects could in- terfere with its proper operation and could be propelled inside the vehicle and cause injury. D Do not attach accessories to the windshield, or fit an extra- wide mirror over the rear view mirror. If the SRS airbag deploys, those objects could become projectiles that could seriously in- jure vehicle occupants. – CONTINUED – 1-59 Legacy U.S.A..(ENG.)A2280BE–A HB1047BB The driver’s SRS frontal airbag is stowed in the center portion of the steering wheel. The passenger’s SRS frontal airbag is stowed near the top of the dashboard under an “SRS AIRBAG” mark. In a moderate to severe frontal collision, the driver’s and front passen- ger’s SRS frontal airbags deploy and supplement the seatbelts by reduc- ing the impact on the driver’s and front passenger’s head and chest. B Operation CAUTION Do not touch the SRS airbag system components around the steering wheel and dashboard with bare hands right after deploy- ment. Doing so can cause burns because the components can be very hot as a result of deployment. 1-60 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Driver’s side Passenger’s side SRS airbags deploy as soon as a collision occurs. After deployment, SRS airbags start to deflate immediately so that the driver’s vision is not obstructed. OM-H0384 The SRS airbag can function only when the ignition switch is in the “ON” position. If the front sub sensors inside the both front fenders and the impact sensors in the airbag control module detect a certain predetermined amount of force during a frontal collision, the control module sends signals to the frontal airbag modules instructing them to inflate the SRS frontal airbags. Then both airbag modules produce gas, which instantly inflates driver’s and passenger’s SRS frontal airbags. After the deployment, the SRS airbags immediately start to deflate so that the driver’s vision is not obstructed. The time required from detecting impact to the deflating SRS airbag after deployment is shorter than the blink of an eye. The front passenger’s SRS frontal airbag deploys together with driv- er’s SRS frontal airbag even when no one occupies the front passen- ger’s seat. When the SRS frontal airbags deploy, the driver’s and front passen- ger’s seatbelt pretensioners operate at the same time. Although it is highly unlikely that the SRS airbag would activate in a non-accident situation, should it occur, the SRS airbag will deflate quickly, not obscuring vision and will not interfere with the driver’s ability to maintain control of the vehicle. – CONTINUED – 1-61 Legacy U.S.A..(ENG.)A2280BE–A When the SRS airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occurrences are normal result of the deployment. This smoke does not indicate a fire in the vehicle. The SRS frontal airbag is designed to deploy in the event of an acci- dent involving a moderate to severe frontal collision. It is basically not designed to deploy in lesser frontal impacts because the necessary protection can be achieved by the seatbelt alone. Also, it is basically not designed to deploy in side or rear impacts or in roll-over acci- dents because deployment of the SRS frontal airbag would not help the occupant in those situations. The SRS airbag is designed to func- tion on a one-time-only basis. SRS airbag deployment depends on the level of force experienced in the passenger compartment during a collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle itself. n Examples of accident in which the SRS frontal airbag will most likely deploy. A head-on collision against a thick concrete wall at a vehicle speed of 12 to 19 mph (20 to 30 km/h) activates the SRS frontal airbag. The SRS frontal airbag will also be activated when the vehicle is exposed to a frontal impact similar in fashion and magnitude to the above-men- tioned collision. HB1055BA 1-62 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags n Examples of the types of accidents in which it is possible that the SRS frontal airbag will deploy. The SRS frontal airbag may be activated when the vehicle sustains a hard impact in the undercarriage area from the road surface (such as when the vehicle plunges into a deep ditch, is severely bumped or knocked hard against an obstacle on the road such as a curb). HB1056BA HB1057BA n Examples of the types of accidents in which the SRS frontal airbag is unlikely to deploy. There are many types of collisions which might not necessarily require SRS frontal airbag deployment. If the vehicle strikes an object, such as a telephone pole or sign pole, or if it slides under a truck’s load bed, or if it sustains an oblique offset frontal impact, the SRS frontal airbag may not deploy depending on the level of accident forces in- volved. The vehicle sustains an oblique offset frontal impact. HB1041AB HB1042BB HB0311 – CONTINUED – 1-63 Legacy U.S.A..(ENG.)A2280BE–A n Examples of the types of accidents in which the SRS frontal airbag will basically not deploy. The SRS frontal airbag is basically not designed to deploy if the vehicle is struck from side or from behind, or if it rolls onto its side or roof, or if it is involved in a low-speed frontal collision. The vehicle is struck from the side. HB1043BB HB0313 HB1044AB In an accident where the vehicle is impacted more than once, the SRS frontal airbag deploys only once on the first impact. Example: In the case of a double collision, first with another vehicle, then against a concrete wall in immediate succession, the SRS frontal airbag is activated on the first impact but not on the second. HB1070BB 1-64 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags J SRS side airbag (if equipped) WARNING D The SRS aide airbag is designed as only a supplement to the primary protection provided by the seatbelt. It does not do away with the need to fasten seatbelts. It is also important to wear your seatbelt to help avoid injuries that can result when an occupant is not seated in a proper upright position. D Do not sit or lean unnecessarily close to either front door. The SRS side airbag is stored in both front seat seatbacks next to the door, and it provides protection by deploying rapidly (faster than the blink of an eye) in the event of a side impact collision. Howev- er, the force of SRS side airbag deployment may cause injuries if your head or other body parts are too close to the SRS side air- bag. D Do not rest your arm on either front door or its internal trim. It could be injured in the event of SRS side airbag deployment. D Never allow a child to kneel on the front passenger’s seat fac- ing the side window or to wrap his/her arms around the front seat seatback. In the event of an accident, the force of SRS side airbag deployment could seriously injure or even kill the child because his/her head or arms or other body parts are close to the side air- bag. Since your vehicle is also equipped with a passenger’s SRS frontal airbag, children aged 12 and under should be placed in the rear seat anyway and should be properly restrained at all times. – CONTINUED – 1-65 Legacy U.S.A..(ENG.)A2280BE–A Do not sit or lean unnecessary close to the front door. Do not rest your arm on either front door or its internal trim. HB0352 HB0353 Never allow a child to kneel on the front passenger’s seat facing the side window. Never allow a child to wrap his/her arms around the front seatback. HB0354 HB0355 WARNING D Do not attach accessories to the door trim or near either SRS side airbags and do not place objects near the SRS side airbags. In the event of the SRS side airbag deployment, they could be propelled dangerously toward the vehicle’s occupants and cause injuries. D Do not put any kind of cover or clothes or other objects over either front seatback and do not attach labels or stickers to the front seat surface on or near the SRS side airbag. They could pre- vent proper deployment of the SRS side airbag, reducing protec- tion available to the front seat’s occupant. 1-66 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags Do not put any kind of cover over either seatback. Do not attach accessories to the door trim or near either side airbag and do not place objects near either side air- bag. HB0366 HS0353 The SRS side airbag is stored in the door side of each front seatback, which bears an “SRS AIRBAG” label. In a moderate to severe side impact collision, the SRS side airbag on the impacted side of the vehicle deploys between the occupant and the door panel and supplements the seatbelt by reducing the impact on the occupant’s chest. B Operation CAUTION Do not touch the SRS side airbag system components around the front seatback with bare hands right after deployment. Doing so can cause burns because the components can be very hot as a result of deployment. – CONTINUED – 1-67 Legacy U.S.A..(ENG.)A2280BE–A SRS side airbag deploys as soon as a collision occurs. After deployment, SRS side airbag starts to deflate immedi- ately. HB0359 The SRS side airbag can function only when the ignition switch is in the “ON” position. The driver’s and front passenger’s SRS side airbags deploy indepen- dently of each other since each has its own impact sensor. Also, the SRS side airbag deploys independently of the frontal airbags in the steering wheel and instrument panel. An impact sensor is incorporated into each of the vehicle’s center pil- lars. If either sensor detects a certain predetermined amount of force during a side impact collision, the control module sends a signal to the side airbag module on the impacted side of the vehicle, instruct- ing it to inflate the SRS side airbag. Then the side airbag module pro- duces gas, which instantly inflates the SRS side airbag. After the de- ployment, the SRS side airbag immediately starts to deflate. The time required from detecting impact to deflating of the SRS side airbag af- ter deployment is shorter than the blink of an eye. The SRS side airbag deploys even when no one occupies the seat on the side of which an impact is applied. 1-68 Legacy U.S.A..(ENG.)A2280BE–A Seat, seatbelt and SRS airbags When the SRS side airbag deploys, a sudden, fairly loud inflation noise will be heard and some smoke will be released. These occur- rences are normal result of the deployment. This smoke does not indi- cate a fire in the vehicle. The SRS side airbag is designed to deploy in the event of an accident involving a moderate to severe side impact collision. It is basically not designed to deploy in lesser side impact. Also, it is basically not de- signed to deploy in frontal or rear impacts because SRS side airbag deployment would not help the occupant in those situations. Each SRS side airbag is designed to function on a one-time-only ba- sis. SRS side airbag deployment depends on the level of force experi- enced in the passenger compartment during a side impact collision. That level differs from one type of collision to another, and it may have no bearing on the visible damage done to the vehicle itself. n Example of the type of accident in which the SRS side airbag will most likely deploy. A severe side impact near the front seat activates the SRS side air- bag. HB0313 – CONTINUED – 1-69 Legacy U.S.A..(ENG.)A2280BE–A n Examples of the types of accidents in which the SRS side air- bag is unlikely to deploy. There are many types of collisions which might not necessarily require SRS side airbag deployment. In the event of accidents like those illus- trated below, the SRS side airbag may not deploy depending on the level of accident forces involved. The vehicle is involved in an oblique side impact. The vehicle is involved in a side impact in an area outside the passenger compartment. The vehicle strikes a telephone pole or similar object. HB0361 HB0362 HB0363 HB1045AB HB1044AB

Boost Classifieds - Car Advice, Reviews, Events & Classifieds

2001 Subaru Legacy Owners Manual